/*
* Calculate the Au1x00's LCD clock based on the current
* cpu clock and the system bus clock, and try to keep it
* below 40 MHz (the Pb1000 board can lock-up if the LCD
* clock is over 40 MHz).
*/
void set_au1x00_lcd_clock(void)
{
unsigned int static_cfg0;
unsigned int sys_busclk =
(get_au1x00_speed()/1000) /
((int)(au_readl(SYS_POWERCTRL)&0x03) + 2);
static_cfg0 = au_readl(MEM_STCFG0);
if (static_cfg0 & (1<<11))
lcd_clock = sys_busclk / 5; /* note: BCLK switching fails with D5 */
else
lcd_clock = sys_busclk / 4;
if (lcd_clock > 50000) /* Epson MAX */
printk(__FUNCTION__
": warning: LCD clock too high (%d KHz)\n",
lcd_clock);
}
static int pm_do_freq(ctl_table * ctl, int write, struct file *file,
void *buffer, size_t * len)
{
int retval = 0, i;
unsigned long val, pll;
#define TMPBUFLEN 64
#define MAX_CPU_FREQ 396
char buf[TMPBUFLEN], *p;
unsigned long flags, intc0_mask, intc1_mask;
unsigned long old_baud_base, old_cpu_freq, baud_rate, old_clk,
old_refresh;
unsigned long new_baud_base, new_cpu_freq, new_clk, new_refresh;
spin_lock_irqsave(&pm_lock, flags);
if (!write) {
*len = 0;
} else {
/* Parse the new frequency */
if (*len > TMPBUFLEN - 1) {
spin_unlock_irqrestore(&pm_lock, flags);
return -EFAULT;
}
if (copy_from_user(buf, buffer, *len)) {
spin_unlock_irqrestore(&pm_lock, flags);
return -EFAULT;
}
buf[*len] = 0;
p = buf;
val = simple_strtoul(p, &p, 0);
if (val > MAX_CPU_FREQ) {
spin_unlock_irqrestore(&pm_lock, flags);
return -EFAULT;
}
pll = val / 12;
if ((pll > 33) || (pll < 7)) { /* 396 MHz max, 84 MHz min */
/* revisit this for higher speed cpus */
spin_unlock_irqrestore(&pm_lock, flags);
return -EFAULT;
}
old_baud_base = get_au1x00_uart_baud_base();
old_cpu_freq = get_au1x00_speed();
new_cpu_freq = pll * 12 * 1000000;
new_baud_base = (new_cpu_freq / (2 * ((int)(au_readl(SYS_POWERCTRL)&0x03) + 2) * 16));
set_au1x00_speed(new_cpu_freq);
set_au1x00_uart_baud_base(new_baud_base);
old_refresh = au_readl(MEM_SDREFCFG) & 0x1ffffff;
new_refresh =
((old_refresh * new_cpu_freq) /
old_cpu_freq) | (au_readl(MEM_SDREFCFG) & ~0x1ffffff);
au_writel(pll, SYS_CPUPLL);
au_sync_delay(1);
au_writel(new_refresh, MEM_SDREFCFG);
au_sync_delay(1);
for (i = 0; i < 4; i++) {
if (au_readl
(UART_BASE + UART_MOD_CNTRL +
i * 0x00100000) == 3) {
old_clk =
au_readl(UART_BASE + UART_CLK +
i * 0x00100000);
// baud_rate = baud_base/clk
baud_rate = old_baud_base / old_clk;
/* we won't get an exact baud rate and the error
* could be significant enough that our new
* calculation will result in a clock that will
* give us a baud rate that's too far off from
* what we really want.
*/
if (baud_rate > 100000)
baud_rate = 115200;
else if (baud_rate > 50000)
baud_rate = 57600;
else if (baud_rate > 30000)
baud_rate = 38400;
else if (baud_rate > 17000)
baud_rate = 19200;
else
(baud_rate = 9600);
// new_clk = new_baud_base/baud_rate
new_clk = new_baud_base / baud_rate;
au_writel(new_clk,
UART_BASE + UART_CLK +
i * 0x00100000);
au_sync_delay(10);
}
}
}
/* We don't want _any_ interrupts other than
* match20. Otherwise our calibrate_delay()
* calculation will be off, potentially a lot.
*/
intc0_mask = save_local_and_disable(0);
intc1_mask = save_local_and_disable(1);
local_enable_irq(AU1000_TOY_MATCH2_INT);
spin_unlock_irqrestore(&pm_lock, flags);
calibrate_delay();
restore_local_and_enable(0, intc0_mask);
restore_local_and_enable(1, intc1_mask);
return retval;
}
