C++ (Cpp) has_usb示例

示例#1

文件： split_util.c 项目： Fahrradflucht/qmk_firmware

static void setup_handedness(void) {
  #ifdef EE_HANDS
    isLeftHand = eeprom_read_byte(EECONFIG_HANDEDNESS);
  #else
    #ifdef I2C_MASTER_RIGHT
      isLeftHand = !has_usb();
    #else
      isLeftHand = has_usb();
    #endif
  #endif
}

示例#2

文件： split_util.c 项目： 0tsuki/qmk_firmware

static void setup_handedness(void) {
  #ifdef EE_HANDS
    isLeftHand = eeprom_read_byte(EECONFIG_HANDEDNESS);
  #else
    // I2C_MASTER_RIGHT is deprecated, use MASTER_RIGHT instead, since this works for both serial and i2c
    #if defined(I2C_MASTER_RIGHT) || defined(MASTER_RIGHT)
      isLeftHand = !has_usb();
    #else
      isLeftHand = has_usb();
    #endif
  #endif
}

示例#3

文件： split_util.c 项目： Fahrradflucht/qmk_firmware

// this code runs before the usb and keyboard is initialized
void matrix_setup(void) {
    split_keyboard_setup();

    if (!has_usb()) {
        keyboard_slave_loop();
    }
}

示例#4

文件： split_util.c 项目： anechiporuk/qmk_firmware

// this code runs before the usb and keyboard is initialized
void matrix_setup(void) {
    split_keyboard_setup();

    if (!has_usb()) {
        //rgblight_init();
        keyboard_slave_loop();
    }
}

示例#5

文件： split_util.c 项目： ju0/qmk_firmware

static void setup_handedness(void) {
  #ifdef SPLIT_HAND_PIN
    // Test pin SPLIT_HAND_PIN for High/Low, if low it's right hand
    pinMode(SPLIT_HAND_PIN, PinDirectionInput);
    isLeftHand = digitalRead(SPLIT_HAND_PIN);
  #else
    #ifdef EE_HANDS
      isLeftHand = eeprom_read_byte(EECONFIG_HANDEDNESS);
    #else
      #ifdef MASTER_RIGHT
        isLeftHand = !has_usb();
      #else
        isLeftHand = has_usb();
      #endif
    #endif
  #endif
}

示例#6

文件： split_util.c 项目： anechiporuk/qmk_firmware

static void setup_handedness(void) {
  #ifdef SPLIT_HAND_PIN
    // Test pin SPLIT_HAND_PIN for High/Low, if low it's right hand
    pinMode(SPLIT_HAND_PIN, PinDirectionInput);
    isLeftHand = digitalRead(SPLIT_HAND_PIN);
  #else
    #ifdef EE_HANDS
      isLeftHand = eeprom_read_byte(EECONFIG_HANDEDNESS);
    #else
      // I2C_MASTER_RIGHT is deprecated, use MASTER_RIGHT instead, since this works for both serial and i2c
      #if defined(I2C_MASTER_RIGHT) || defined(MASTER_RIGHT)
        isLeftHand = !has_usb();
      #else
        isLeftHand = has_usb();
      #endif
    #endif
  #endif
}

示例#7

文件： keymap.c 项目： Depariel/qmk_firmware

void matrix_init_user(void) {
    #ifdef RGBLIGHT_ENABLE
      RGB_current_mode = rgblight_config.mode;
    #endif
    //SSD1306 OLED init, make sure to add #define SSD1306OLED in config.h
    #ifdef SSD1306OLED
        iota_gfx_init(!has_usb());   // turns on the display
    #endif
}

示例#8

文件： split_util.c 项目： anechiporuk/qmk_firmware

void split_keyboard_setup(void) {
   setup_handedness();

   if (has_usb()) {
      keyboard_master_setup();
   } else {
      keyboard_slave_setup();
   }
   sei();
}

示例#9

文件： keymap.c 项目： j-chan-hkust/qmk_firmware

void matrix_init_user(void) {
    #ifdef AUDIO_ENABLE
        startup_user();
    #endif
    #ifdef RGBLIGHT_ENABLE
      RGB_current_mode = rgblight_config.mode;
    #endif
    //SSD1306 OLED init, make sure to add #define SSD1306OLED in config.h
    #ifdef SSD1306OLED
        TWI_Init(TWI_BIT_PRESCALE_1, TWI_BITLENGTH_FROM_FREQ(1, 800000));
        iota_gfx_init(!has_usb());   // turns on the display
    #endif
}

示例#10

文件： keymap.c 项目： bellwood4486/qmk_firmware

void matrix_init_keymap(void) {
    #ifdef RGBLIGHT_ENABLE
      RGB_current_mode = rgblight_config.mode;
    #endif
    //SSD1306 OLED init, make sure to add #define SSD1306OLED in config.h
    #ifdef SSD1306OLED
        iota_gfx_init(!has_usb());   // turns on the display
    #endif

  DDRD &= ~(1<<5);
  PORTD &= ~(1<<5);

  DDRB &= ~(1<<0);
  PORTB &= ~(1<<0);}

示例#11

文件： matrix.c 项目： climbalima/Split_QMK

int main(void)
{
    setup_hardware();
    setup_set_handedness();
    sei();

    /* wait for USB startup to get ready for debug output */
    uint8_t timeout = 200;  // timeout when USB is not available
    while (timeout-- && USB_DeviceState != DEVICE_STATE_Configured) {
        wait_ms(5);
#if defined(INTERRUPT_CONTROL_ENDPOINT)
        ;
#else
        USB_USBTask();
#endif
    }

    /* if (USB_DeviceState != DEVICE_STATE_Configured) { */
    if (!has_usb()) {
        // USB failed to connect, so run this device in slave mode.
        matrix_init();
        serial_slave_init();

        while (1) {
            matrix_slave_scan();
        }
    }

    /* init modules */
    keyboard_init();
    host_set_driver(&lufa_driver);

#ifdef SLEEP_LED_ENABLE
    sleep_led_init();
#endif

    while (1) {
        keyboard_task();

#if !defined(INTERRUPT_CONTROL_ENDPOINT)
        USB_USBTask();
#endif
    }
}

示例#12

文件： keymap.c 项目： 0xdec/qmk_firmware

void matrix_init_keymap(void) {
  //SSD1306 OLED init, make sure to add #define SSD1306OLED in config.h
  iota_gfx_init(!has_usb());   // turns on the display
}

示例#13

文件： keymap.c 项目： Xyverz/qmk_firmware

oled_rotation_t oled_init_user(oled_rotation_t rotation) {
  if (!has_usb())
    return OLED_ROTATION_180;  // flip 180 for offhand
  return rotation;
}