static int orinoco_cs_config(struct pcmcia_device *link) { struct orinoco_private *priv = link->priv; struct hermes *hw = &priv->hw; int ret; void __iomem *mem; link->config_flags |= CONF_AUTO_SET_VPP | CONF_AUTO_CHECK_VCC | CONF_AUTO_SET_IO | CONF_ENABLE_IRQ; if (ignore_cis_vcc) link->config_flags &= ~CONF_AUTO_CHECK_VCC; ret = pcmcia_loop_config(link, orinoco_cs_config_check, NULL); if (ret) { if (!ignore_cis_vcc) printk(KERN_ERR PFX "GetNextTuple(): No matching " "CIS configuration. Maybe you need the " "ignore_cis_vcc=1 parameter.\n"); goto failed; } mem = ioport_map(link->resource[0]->start, resource_size(link->resource[0])); if (!mem) goto failed; /* */ hermes_struct_init(hw, mem, HERMES_16BIT_REGSPACING); ret = pcmcia_request_irq(link, orinoco_interrupt); if (ret) goto failed; ret = pcmcia_enable_device(link); if (ret) goto failed; /* */ if (orinoco_init(priv) != 0) { printk(KERN_ERR PFX "orinoco_init() failed\n"); goto failed; } /* */ if (orinoco_if_add(priv, link->resource[0]->start, link->irq, NULL) != 0) { printk(KERN_ERR PFX "orinoco_if_add() failed\n"); goto failed; } return 0; failed: orinoco_cs_release(link); return -ENODEV; } /* */
static int orinoco_cs_config(struct pcmcia_device *link) { struct orinoco_private *priv = link->priv; hermes_t *hw = &priv->hw; int ret; void __iomem *mem; link->config_flags |= CONF_AUTO_SET_VPP | CONF_AUTO_CHECK_VCC | CONF_AUTO_SET_IO | CONF_ENABLE_IRQ; if (ignore_cis_vcc) link->config_flags &= ~CONF_AUTO_CHECK_VCC; ret = pcmcia_loop_config(link, orinoco_cs_config_check, NULL); if (ret) { if (!ignore_cis_vcc) printk(KERN_ERR PFX "GetNextTuple(): No matching " "CIS configuration. Maybe you need the " "ignore_cis_vcc=1 parameter.\n"); goto failed; } ret = pcmcia_request_irq(link, orinoco_interrupt); if (ret) goto failed; /* We initialize the hermes structure before completing PCMCIA * configuration just in case the interrupt handler gets * called. */ mem = ioport_map(link->resource[0]->start, resource_size(link->resource[0])); if (!mem) goto failed; hermes_struct_init(hw, mem, HERMES_16BIT_REGSPACING); ret = pcmcia_enable_device(link); if (ret) goto failed; /* Initialise the main driver */ if (orinoco_init(priv) != 0) { printk(KERN_ERR PFX "orinoco_init() failed\n"); goto failed; } /* Register an interface with the stack */ if (orinoco_if_add(priv, link->resource[0]->start, link->irq, NULL) != 0) { printk(KERN_ERR PFX "orinoco_if_add() failed\n"); goto failed; } return 0; failed: orinoco_cs_release(link); return -ENODEV; } /* orinoco_cs_config */
static int airport_attach(struct macio_dev *mdev, const struct of_device_id *match) { struct orinoco_private *priv; struct net_device *dev; struct airport *card; unsigned long phys_addr; hermes_t *hw; if (macio_resource_count(mdev) < 1 || macio_irq_count(mdev) < 1) { printk(KERN_ERR PFX "Wrong interrupt/addresses in OF tree\n"); return -ENODEV; } /* Allocate space for private device-specific data */ dev = alloc_orinocodev(sizeof(*card), airport_hard_reset); if (! dev) { printk(KERN_ERR PFX "Cannot allocate network device\n"); return -ENODEV; } priv = netdev_priv(dev); card = priv->card; hw = &priv->hw; card->mdev = mdev; if (macio_request_resource(mdev, 0, "airport")) { printk(KERN_ERR PFX "can't request IO resource !\n"); free_orinocodev(dev); return -EBUSY; } SET_MODULE_OWNER(dev); SET_NETDEV_DEV(dev, &mdev->ofdev.dev); macio_set_drvdata(mdev, dev); /* Setup interrupts & base address */ dev->irq = macio_irq(mdev, 0); phys_addr = macio_resource_start(mdev, 0); /* Physical address */ printk(KERN_DEBUG PFX "Physical address %lx\n", phys_addr); dev->base_addr = phys_addr; card->vaddr = ioremap(phys_addr, AIRPORT_IO_LEN); if (!card->vaddr) { printk(KERN_ERR PFX "ioremap() failed\n"); goto failed; } hermes_struct_init(hw, card->vaddr, HERMES_16BIT_REGSPACING); /* Power up card */ pmac_call_feature(PMAC_FTR_AIRPORT_ENABLE, macio_get_of_node(mdev), 0, 1); ssleep(1); /* Reset it before we get the interrupt */ hermes_init(hw); if (request_irq(dev->irq, orinoco_interrupt, 0, dev->name, dev)) { printk(KERN_ERR PFX "Couldn't get IRQ %d\n", dev->irq); goto failed; } card->irq_requested = 1; /* Tell the stack we exist */ if (register_netdev(dev) != 0) { printk(KERN_ERR PFX "register_netdev() failed\n"); goto failed; } printk(KERN_DEBUG PFX "Card registered for interface %s\n", dev->name); card->ndev_registered = 1; return 0; failed: airport_detach(mdev); return -ENODEV; } /* airport_attach */
static int orinoco_tmd_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) { int err; struct orinoco_private *priv; struct orinoco_pci_card *card; void __iomem *hermes_io, *bridge_io; err = pci_enable_device(pdev); if (err) { ; return err; } err = pci_request_regions(pdev, DRIVER_NAME); if (err) { ; goto fail_resources; } bridge_io = pci_iomap(pdev, 1, 0); if (!bridge_io) { ; err = -EIO; goto fail_map_bridge; } hermes_io = pci_iomap(pdev, 2, 0); if (!hermes_io) { ; err = -EIO; goto fail_map_hermes; } /* Allocate network device */ priv = alloc_orinocodev(sizeof(*card), &pdev->dev, orinoco_tmd_cor_reset, NULL); if (!priv) { ; err = -ENOMEM; goto fail_alloc; } card = priv->card; card->bridge_io = bridge_io; hermes_struct_init(&priv->hw, hermes_io, HERMES_16BIT_REGSPACING); err = request_irq(pdev->irq, orinoco_interrupt, IRQF_SHARED, DRIVER_NAME, priv); if (err) { ; err = -EBUSY; goto fail_irq; } err = orinoco_tmd_cor_reset(priv); if (err) { ; goto fail; } err = orinoco_init(priv); if (err) { ; goto fail; } err = orinoco_if_add(priv, 0, 0, NULL); if (err) { ; goto fail; } pci_set_drvdata(pdev, priv); return 0; fail: free_irq(pdev->irq, priv); fail_irq: pci_set_drvdata(pdev, NULL); free_orinocodev(priv); fail_alloc: pci_iounmap(pdev, hermes_io); fail_map_hermes: pci_iounmap(pdev, bridge_io); fail_map_bridge: pci_release_regions(pdev); fail_resources: pci_disable_device(pdev); return err; }
static int orinoco_cs_config(struct pcmcia_device *link) { struct net_device *dev = link->priv; struct orinoco_private *priv = netdev_priv(dev); struct orinoco_pccard *card = priv->card; hermes_t *hw = &priv->hw; int last_fn, last_ret; u_char buf[64]; config_info_t conf; tuple_t tuple; cisparse_t parse; void __iomem *mem; /* Look up the current Vcc */ CS_CHECK(GetConfigurationInfo, pcmcia_get_configuration_info(link, &conf)); /* * In this loop, we scan the CIS for configuration table * entries, each of which describes a valid card * configuration, including voltage, IO window, memory window, * and interrupt settings. * * We make no assumptions about the card to be configured: we * use just the information available in the CIS. In an ideal * world, this would work for any PCMCIA card, but it requires * a complete and accurate CIS. In practice, a driver usually * "knows" most of these things without consulting the CIS, * and most client drivers will only use the CIS to fill in * implementation-defined details. */ tuple.Attributes = 0; tuple.TupleData = buf; tuple.TupleDataMax = sizeof(buf); tuple.TupleOffset = 0; tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY; CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(link, &tuple)); while (1) { cistpl_cftable_entry_t *cfg = &(parse.cftable_entry); cistpl_cftable_entry_t dflt = { .index = 0 }; if ( (pcmcia_get_tuple_data(link, &tuple) != 0) || (pcmcia_parse_tuple(link, &tuple, &parse) != 0)) goto next_entry; if (cfg->flags & CISTPL_CFTABLE_DEFAULT) dflt = *cfg; if (cfg->index == 0) goto next_entry; link->conf.ConfigIndex = cfg->index; /* Use power settings for Vcc and Vpp if present */ /* Note that the CIS values need to be rescaled */ if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) { if (conf.Vcc != cfg->vcc.param[CISTPL_POWER_VNOM] / 10000) { DEBUG(2, "orinoco_cs_config: Vcc mismatch (conf.Vcc = %d, cfg CIS = %d)\n", conf.Vcc, cfg->vcc.param[CISTPL_POWER_VNOM] / 10000); if (!ignore_cis_vcc) goto next_entry; } } else if (dflt.vcc.present & (1 << CISTPL_POWER_VNOM)) { if (conf.Vcc != dflt.vcc.param[CISTPL_POWER_VNOM] / 10000) { DEBUG(2, "orinoco_cs_config: Vcc mismatch (conf.Vcc = %d, dflt CIS = %d)\n", conf.Vcc, dflt.vcc.param[CISTPL_POWER_VNOM] / 10000); if(!ignore_cis_vcc) goto next_entry; } } if (cfg->vpp1.present & (1 << CISTPL_POWER_VNOM)) link->conf.Vpp = cfg->vpp1.param[CISTPL_POWER_VNOM] / 10000; else if (dflt.vpp1.present & (1 << CISTPL_POWER_VNOM)) link->conf.Vpp = dflt.vpp1.param[CISTPL_POWER_VNOM] / 10000; /* Do we need to allocate an interrupt? */ link->conf.Attributes |= CONF_ENABLE_IRQ; /* IO window settings */ link->io.NumPorts1 = link->io.NumPorts2 = 0; if ((cfg->io.nwin > 0) || (dflt.io.nwin > 0)) { cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt.io; link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO; if (!(io->flags & CISTPL_IO_8BIT)) link->io.Attributes1 = IO_DATA_PATH_WIDTH_16; if (!(io->flags & CISTPL_IO_16BIT)) link->io.Attributes1 = IO_DATA_PATH_WIDTH_8; link->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK; link->io.BasePort1 = io->win[0].base; link->io.NumPorts1 = io->win[0].len; if (io->nwin > 1) { link->io.Attributes2 = link->io.Attributes1; link->io.BasePort2 = io->win[1].base; link->io.NumPorts2 = io->win[1].len; } /* This reserves IO space but doesn't actually enable it */ if (pcmcia_request_io(link, &link->io) != 0) goto next_entry; } /* If we got this far, we're cool! */ break; next_entry: pcmcia_disable_device(link); last_ret = pcmcia_get_next_tuple(link, &tuple); if (last_ret == CS_NO_MORE_ITEMS) { printk(KERN_ERR PFX "GetNextTuple(): No matching " "CIS configuration. Maybe you need the " "ignore_cis_vcc=1 parameter.\n"); goto cs_failed; } } /* * Allocate an interrupt line. Note that this does not assign * a handler to the interrupt, unless the 'Handler' member of * the irq structure is initialized. */ CS_CHECK(RequestIRQ, pcmcia_request_irq(link, &link->irq)); /* We initialize the hermes structure before completing PCMCIA * configuration just in case the interrupt handler gets * called. */ mem = ioport_map(link->io.BasePort1, link->io.NumPorts1); if (!mem) goto cs_failed; hermes_struct_init(hw, mem, HERMES_16BIT_REGSPACING); /* * This actually configures the PCMCIA socket -- setting up * the I/O windows and the interrupt mapping, and putting the * card and host interface into "Memory and IO" mode. */ CS_CHECK(RequestConfiguration, pcmcia_request_configuration(link, &link->conf)); /* Ok, we have the configuration, prepare to register the netdev */ dev->base_addr = link->io.BasePort1; dev->irq = link->irq.AssignedIRQ; card->node.major = card->node.minor = 0; SET_NETDEV_DEV(dev, &handle_to_dev(link)); /* Tell the stack we exist */ if (register_netdev(dev) != 0) { printk(KERN_ERR PFX "register_netdev() failed\n"); goto failed; } /* At this point, the dev_node_t structure(s) needs to be * initialized and arranged in a linked list at link->dev_node. */ strcpy(card->node.dev_name, dev->name); link->dev_node = &card->node; /* link->dev_node being non-NULL is also used to indicate that the net_device has been registered */ /* Finally, report what we've done */ printk(KERN_DEBUG "%s: " DRIVER_NAME " at %s, irq %d, io " "0x%04x-0x%04x\n", dev->name, dev->dev.parent->bus_id, link->irq.AssignedIRQ, link->io.BasePort1, link->io.BasePort1 + link->io.NumPorts1 - 1); return 0; cs_failed: cs_error(link, last_fn, last_ret); failed: orinoco_cs_release(link); return -ENODEV; } /* orinoco_cs_config */ /* * After a card is removed, orinoco_cs_release() will unregister the * device, and release the PCMCIA configuration. If the device is * still open, this will be postponed until it is closed. */ static void orinoco_cs_release(struct pcmcia_device *link) { struct net_device *dev = link->priv; struct orinoco_private *priv = netdev_priv(dev); unsigned long flags; /* We're committed to taking the device away now, so mark the * hardware as unavailable */ spin_lock_irqsave(&priv->lock, flags); priv->hw_unavailable++; spin_unlock_irqrestore(&priv->lock, flags); pcmcia_disable_device(link); if (priv->hw.iobase) ioport_unmap(priv->hw.iobase); } /* orinoco_cs_release */ static int orinoco_cs_suspend(struct pcmcia_device *link) { struct net_device *dev = link->priv; struct orinoco_private *priv = netdev_priv(dev); struct orinoco_pccard *card = priv->card; int err = 0; unsigned long flags; /* This is probably racy, but I can't think of a better way, short of rewriting the PCMCIA layer to not suck :-( */ if (! test_bit(0, &card->hard_reset_in_progress)) { spin_lock_irqsave(&priv->lock, flags); err = __orinoco_down(dev); if (err) printk(KERN_WARNING "%s: Error %d downing interface\n", dev->name, err); netif_device_detach(dev); priv->hw_unavailable++; spin_unlock_irqrestore(&priv->lock, flags); } return 0; } static int orinoco_cs_resume(struct pcmcia_device *link) { struct net_device *dev = link->priv; struct orinoco_private *priv = netdev_priv(dev); struct orinoco_pccard *card = priv->card; int err = 0; if (! test_bit(0, &card->hard_reset_in_progress)) { err = orinoco_reinit_firmware(dev); if (err) { printk(KERN_ERR "%s: Error %d re-initializing firmware\n", dev->name, err); return -EIO; } spin_lock(&priv->lock); netif_device_attach(dev); priv->hw_unavailable--; if (priv->open && ! priv->hw_unavailable) { err = __orinoco_up(dev); if (err) printk(KERN_ERR "%s: Error %d restarting card\n", dev->name, err); } spin_unlock(&priv->lock); } return err; } /********************************************************************/ /* Module initialization */ /********************************************************************/ /* Can't be declared "const" or the whole __initdata section will * become const */ static char version[] __initdata = DRIVER_NAME " " DRIVER_VERSION " (David Gibson <*****@*****.**>, " "Pavel Roskin <*****@*****.**>, et al)"; /* * PCMCIA IDs that are also defined in hostap_cs. */ static struct pcmcia_device_id orinoco_overlap_cs_ids[] = { PCMCIA_DEVICE_MANF_CARD(0x000b, 0x7100), /* SonicWALL Long Range Wireless Card */ PCMCIA_DEVICE_MANF_CARD(0x000b, 0x7300), /* Sohoware NCP110, Philips 802.11b */ PCMCIA_DEVICE_MANF_CARD(0x0101, 0x0777), /* 3Com AirConnect PCI 777A */ PCMCIA_DEVICE_MANF_CARD(0x0126, 0x8000), /* PROXIM RangeLAN-DS/LAN PC CARD */ PCMCIA_DEVICE_MANF_CARD(0x0138, 0x0002), /* Compaq WL100 11 Mbps Wireless Adapter */ PCMCIA_DEVICE_MANF_CARD(0x0250, 0x0002), /* Samsung SWL2000-N 11Mb/s WLAN Card */ PCMCIA_DEVICE_MANF_CARD(0x0274, 0x1612), /* Linksys WPC11 Version 2.5 */ PCMCIA_DEVICE_MANF_CARD(0x0274, 0x1613), /* Linksys WPC11 Version 3 */ PCMCIA_DEVICE_MANF_CARD(0x028a, 0x0002), /* Compaq HNW-100 11 Mbps Wireless Adapter */ PCMCIA_DEVICE_MANF_CARD(0x02aa, 0x0002), /* ASUS SpaceLink WL-100 */ PCMCIA_DEVICE_MANF_CARD(0x50c2, 0x7300), /* Airvast WN-100 */ PCMCIA_DEVICE_MANF_CARD(0xd601, 0x0002), /* Safeway 802.11b, ZCOMAX AirRunner/XI-300 */ PCMCIA_DEVICE_MANF_CARD(0xd601, 0x0005), /* D-Link DCF660, Sandisk Connect SDWCFB-000 */ PCMCIA_DEVICE_PROD_ID12("INTERSIL", "HFA384x/IEEE", 0x74c5e40d, 0xdb472a18), PCMCIA_DEVICE_PROD_ID12("Intersil", "PRISM 2_5 PCMCIA ADAPTER", 0x4b801a17, 0x6345a0bf), PCMCIA_DEVICE_PROD_ID123("Intersil", "PRISM Freedom PCMCIA Adapter", "ISL37100P", 0x4b801a17, 0xf222ec2d, 0x630d52b2), PCMCIA_DEVICE_PROD_ID12("Addtron", "AWP-100 Wireless PCMCIA", 0xe6ec52ce, 0x08649af2), PCMCIA_DEVICE_PROD_ID12("D", "Link DRC-650 11Mbps WLAN Card", 0x71b18589, 0xf144e3ac), PCMCIA_DEVICE_PROD_ID12("D", "Link DWL-650 11Mbps WLAN Card", 0x71b18589, 0xb6f1b0ab), PCMCIA_DEVICE_PROD_ID123("Instant Wireless ", " Network PC CARD", "Version 01.02", 0x11d901af, 0x6e9bd926, 0x4b74baa0), PCMCIA_DEVICE_PROD_ID12("SMC", "SMC2532W-B EliteConnect Wireless Adapter", 0xc4f8b18b, 0x196bd757), PCMCIA_DEVICE_PROD_ID12("SMC", "SMC2632W", 0xc4f8b18b, 0x474a1f2a), PCMCIA_DEVICE_PROD_ID12("BUFFALO", "WLI-PCM-L11G", 0x2decece3, 0xf57ca4b3), PCMCIA_DEVICE_PROD_ID12("BUFFALO", "WLI-CF-S11G", 0x2decece3, 0x82067c18), PCMCIA_DEVICE_PROD_ID12("Compaq", "WL200_11Mbps_Wireless_PCI_Card", 0x54f7c49c, 0x15a75e5b), PCMCIA_DEVICE_PROD_ID12("INTERSIL", "I-GATE 11M PC Card / PC Card plus", 0x74c5e40d, 0x8304ff77), PCMCIA_DEVICE_PROD_ID12("Linksys", "Wireless CompactFlash Card", 0x0733cc81, 0x0c52f395), PCMCIA_DEVICE_PROD_ID12("ZoomAir 11Mbps High", "Rate wireless Networking", 0x273fe3db, 0x32a1eaee), PCMCIA_DEVICE_PROD_ID12("Allied Telesyn", "AT-WCL452 Wireless PCMCIA Radio", 0x5cd01705, 0x4271660f), PCMCIA_DEVICE_NULL, }; static struct pcmcia_driver orinoco_overlap_driver = { .owner = THIS_MODULE, .drv = { .name = OVERLAP_DRIVER_NAME, }, .probe = orinoco_cs_probe, .remove = orinoco_cs_detach, .id_table = orinoco_overlap_cs_ids, .suspend = orinoco_cs_suspend, .resume = orinoco_cs_resume, };
static int orinoco_cs_config(struct pcmcia_device *link) { struct orinoco_private *priv = link->priv; struct orinoco_pccard *card = priv->card; hermes_t *hw = &priv->hw; int last_fn, last_ret; void __iomem *mem; last_ret = pcmcia_loop_config(link, orinoco_cs_config_check, NULL); if (last_ret) { if (!ignore_cis_vcc) printk(KERN_ERR PFX "GetNextTuple(): No matching " "CIS configuration. Maybe you need the " "ignore_cis_vcc=1 parameter.\n"); cs_error(link, RequestIO, last_ret); goto failed; } CS_CHECK(RequestIRQ, pcmcia_request_irq(link, &link->irq)); mem = ioport_map(link->io.BasePort1, link->io.NumPorts1); if (!mem) goto cs_failed; hermes_struct_init(hw, mem, HERMES_16BIT_REGSPACING); CS_CHECK(RequestConfiguration, pcmcia_request_configuration(link, &link->conf)); card->node.major = card->node.minor = 0; if (orinoco_init(priv) != 0) { printk(KERN_ERR PFX "orinoco_init() failed\n"); goto failed; } if (orinoco_if_add(priv, link->io.BasePort1, link->irq.AssignedIRQ) != 0) { printk(KERN_ERR PFX "orinoco_if_add() failed\n"); goto failed; } strcpy(card->node.dev_name, priv->ndev->name); link->dev_node = &card->node; return 0; cs_failed: cs_error(link, last_fn, last_ret); failed: orinoco_cs_release(link); return -ENODEV; }
static int spectrum_cs_config(struct pcmcia_device *link) { struct orinoco_private *priv = link->priv; hermes_t *hw = &priv->hw; int ret; void __iomem *mem; /* * In this loop, we scan the CIS for configuration table * entries, each of which describes a valid card * configuration, including voltage, IO window, memory window, * and interrupt settings. * * We make no assumptions about the card to be configured: we * use just the information available in the CIS. In an ideal * world, this would work for any PCMCIA card, but it requires * a complete and accurate CIS. In practice, a driver usually * "knows" most of these things without consulting the CIS, * and most client drivers will only use the CIS to fill in * implementation-defined details. */ ret = pcmcia_loop_config(link, spectrum_cs_config_check, NULL); if (ret) { if (!ignore_cis_vcc) printk(KERN_ERR PFX "GetNextTuple(): No matching " "CIS configuration. Maybe you need the " "ignore_cis_vcc=1 parameter.\n"); goto failed; } ret = pcmcia_request_irq(link, orinoco_interrupt); if (ret) goto failed; /* We initialize the hermes structure before completing PCMCIA * configuration just in case the interrupt handler gets * called. */ mem = ioport_map(link->io.BasePort1, link->io.NumPorts1); if (!mem) goto failed; hermes_struct_init(hw, mem, HERMES_16BIT_REGSPACING); hw->eeprom_pda = true; /* * This actually configures the PCMCIA socket -- setting up * the I/O windows and the interrupt mapping, and putting the * card and host interface into "Memory and IO" mode. */ ret = pcmcia_request_configuration(link, &link->conf); if (ret) goto failed; /* Reset card */ if (spectrum_cs_hard_reset(priv) != 0) goto failed; /* Initialise the main driver */ if (orinoco_init(priv) != 0) { printk(KERN_ERR PFX "orinoco_init() failed\n"); goto failed; } /* Register an interface with the stack */ if (orinoco_if_add(priv, link->io.BasePort1, link->irq, NULL) != 0) { printk(KERN_ERR PFX "orinoco_if_add() failed\n"); goto failed; } return 0; failed: spectrum_cs_release(link); return -ENODEV; } /* spectrum_cs_config */
static int orinoco_cs_config(struct pcmcia_device *link) { struct net_device *dev = link->priv; struct orinoco_private *priv = netdev_priv(dev); struct orinoco_pccard *card = priv->card; hermes_t *hw = &priv->hw; int last_fn, last_ret; void __iomem *mem; /* * In this loop, we scan the CIS for configuration table * entries, each of which describes a valid card * configuration, including voltage, IO window, memory window, * and interrupt settings. * * We make no assumptions about the card to be configured: we * use just the information available in the CIS. In an ideal * world, this would work for any PCMCIA card, but it requires * a complete and accurate CIS. In practice, a driver usually * "knows" most of these things without consulting the CIS, * and most client drivers will only use the CIS to fill in * implementation-defined details. */ last_ret = pcmcia_loop_config(link, orinoco_cs_config_check, NULL); if (last_ret) { if (!ignore_cis_vcc) printk(KERN_ERR PFX "GetNextTuple(): No matching " "CIS configuration. Maybe you need the " "ignore_cis_vcc=1 parameter.\n"); cs_error(link, RequestIO, last_ret); goto failed; } /* * Allocate an interrupt line. Note that this does not assign * a handler to the interrupt, unless the 'Handler' member of * the irq structure is initialized. */ CS_CHECK(RequestIRQ, pcmcia_request_irq(link, &link->irq)); /* We initialize the hermes structure before completing PCMCIA * configuration just in case the interrupt handler gets * called. */ mem = ioport_map(link->io.BasePort1, link->io.NumPorts1); if (!mem) goto cs_failed; hermes_struct_init(hw, mem, HERMES_16BIT_REGSPACING); /* * This actually configures the PCMCIA socket -- setting up * the I/O windows and the interrupt mapping, and putting the * card and host interface into "Memory and IO" mode. */ CS_CHECK(RequestConfiguration, pcmcia_request_configuration(link, &link->conf)); /* Ok, we have the configuration, prepare to register the netdev */ dev->base_addr = link->io.BasePort1; dev->irq = link->irq.AssignedIRQ; card->node.major = card->node.minor = 0; SET_NETDEV_DEV(dev, &handle_to_dev(link)); /* Tell the stack we exist */ if (register_netdev(dev) != 0) { printk(KERN_ERR PFX "register_netdev() failed\n"); goto failed; } /* At this point, the dev_node_t structure(s) needs to be * initialized and arranged in a linked list at link->dev_node. */ strcpy(card->node.dev_name, dev->name); link->dev_node = &card->node; /* link->dev_node being non-NULL is also * used to indicate that the * net_device has been registered */ /* Finally, report what we've done */ printk(KERN_DEBUG "%s: " DRIVER_NAME " at %s, irq %d, io " "0x%04x-0x%04x\n", dev->name, dev_name(dev->dev.parent), link->irq.AssignedIRQ, link->io.BasePort1, link->io.BasePort1 + link->io.NumPorts1 - 1); return 0; cs_failed: cs_error(link, last_fn, last_ret); failed: orinoco_cs_release(link); return -ENODEV; } /* orinoco_cs_config */
/* * Initialise a card. Mostly similar to PLX code. */ static int orinoco_pci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) { int err = 0; unsigned long pci_iorange; u16 __iomem *pci_ioaddr = NULL; unsigned long pci_iolen; struct orinoco_private *priv = NULL; struct orinoco_pci_card *card; struct net_device *dev = NULL; err = pci_enable_device(pdev); if (err) { printk(KERN_ERR PFX "Cannot enable PCI device\n"); return err; } err = pci_request_regions(pdev, DRIVER_NAME); if (err != 0) { printk(KERN_ERR PFX "Cannot obtain PCI resources\n"); goto fail_resources; } /* Resource 0 is mapped to the hermes registers */ pci_iorange = pci_resource_start(pdev, 0); pci_iolen = pci_resource_len(pdev, 0); pci_ioaddr = ioremap(pci_iorange, pci_iolen); if (!pci_iorange) { printk(KERN_ERR PFX "Cannot remap hardware registers\n"); goto fail_map; } /* Allocate network device */ dev = alloc_orinocodev(sizeof(*card), orinoco_pci_cor_reset); if (! dev) { err = -ENOMEM; goto fail_alloc; } priv = netdev_priv(dev); card = priv->card; card->pci_ioaddr = pci_ioaddr; dev->mem_start = pci_iorange; dev->mem_end = pci_iorange + pci_iolen - 1; SET_MODULE_OWNER(dev); SET_NETDEV_DEV(dev, &pdev->dev); hermes_struct_init(&priv->hw, pci_ioaddr, HERMES_32BIT_REGSPACING); printk(KERN_DEBUG PFX "Detected device %s, mem:0x%lx-0x%lx, irq %d\n", pci_name(pdev), dev->mem_start, dev->mem_end, pdev->irq); err = request_irq(pdev->irq, orinoco_interrupt, SA_SHIRQ, dev->name, dev); if (err) { printk(KERN_ERR PFX "Cannot allocate IRQ %d\n", pdev->irq); err = -EBUSY; goto fail_irq; } dev->irq = pdev->irq; /* Perform a COR reset to start the card */ err = orinoco_pci_cor_reset(priv); if (err) { printk(KERN_ERR PFX "Initial reset failed\n"); goto fail; } err = register_netdev(dev); if (err) { printk(KERN_ERR PFX "Failed to register net device\n"); goto fail; } pci_set_drvdata(pdev, dev); return 0; fail: free_irq(pdev->irq, dev); fail_irq: pci_set_drvdata(pdev, NULL); free_orinocodev(dev); fail_alloc: iounmap(pci_ioaddr); fail_map: pci_release_regions(pdev); fail_resources: pci_disable_device(pdev); return err; }
static struct net_device * airport_attach(struct device_node *of_node) { struct orinoco_private *priv; struct net_device *dev; struct airport *card; unsigned long phys_addr; hermes_t *hw; if (of_node->n_addrs < 1 || of_node->n_intrs < 1) { printk(KERN_ERR "airport: wrong interrupt/addresses in OF tree\n"); return NULL; } /* Allocate space for private device-specific data */ dev = alloc_orinocodev(sizeof(*card), airport_hard_reset); if (! dev) { printk(KERN_ERR "airport: can't allocate device datas\n"); return NULL; } priv = dev->priv; card = priv->card; hw = &priv->hw; card->node = of_node; if (! request_OF_resource(of_node, 0, " (airport)")) { printk(KERN_ERR "airport: can't request IO resource !\n"); kfree(dev); return NULL; } dev->name[0] = '\0'; /* register_netdev will give us an ethX name */ SET_MODULE_OWNER(dev); /* Setup interrupts & base address */ dev->irq = of_node->intrs[0].line; phys_addr = of_node->addrs[0].address; /* Physical address */ printk(KERN_DEBUG "Airport at physical address %lx\n", phys_addr); dev->base_addr = phys_addr; card->vaddr = ioremap(phys_addr, AIRPORT_IO_LEN); if (! card->vaddr) { printk("airport: ioremap() failed\n"); goto failed; } hermes_struct_init(hw, (ulong)card->vaddr, HERMES_MEM, HERMES_16BIT_REGSPACING); /* Power up card */ pmac_call_feature(PMAC_FTR_AIRPORT_ENABLE, card->node, 0, 1); current->state = TASK_UNINTERRUPTIBLE; schedule_timeout(HZ); /* Reset it before we get the interrupt */ hermes_init(hw); if (request_irq(dev->irq, orinoco_interrupt, 0, "Airport", (void *)priv)) { printk(KERN_ERR "airport: Couldn't get IRQ %d\n", dev->irq); goto failed; } card->irq_requested = 1; /* Tell the stack we exist */ if (register_netdev(dev) != 0) { printk(KERN_ERR "airport: register_netdev() failed\n"); goto failed; } printk(KERN_DEBUG "airport: card registered for interface %s\n", dev->name); card->ndev_registered = 1; #ifdef CONFIG_PMAC_PBOOK pmu_register_sleep_notifier(&airport_sleep_notifier); #endif return dev; failed: airport_detach(dev); return NULL; } /* airport_attach */
static int spectrum_cs_config(struct pcmcia_device *link) { struct orinoco_private *priv = link->priv; struct hermes *hw = &priv->hw; int ret; void __iomem *mem; #if 0 /* Not in RHEL */ link->config_flags |= CONF_AUTO_SET_VPP | CONF_AUTO_CHECK_VCC | CONF_AUTO_SET_IO | CONF_ENABLE_IRQ; if (ignore_cis_vcc) link->config_flags &= ~CONF_AUTO_CHECK_VCC; #endif ret = pcmcia_loop_config(link, spectrum_cs_config_check, NULL); if (ret) { if (!ignore_cis_vcc) printk(KERN_ERR PFX "GetNextTuple(): No matching " "CIS configuration. Maybe you need the " "ignore_cis_vcc=1 parameter.\n"); goto failed; } #if 0 /* Not in RHEL */ mem = ioport_map(link->resource[0]->start, resource_size(link->resource[0])); #else mem = ioport_map(link->io.BasePort1, link->io.NumPorts1); #endif if (!mem) goto failed; /* We initialize the hermes structure before completing PCMCIA * configuration just in case the interrupt handler gets * called. */ hermes_struct_init(hw, mem, HERMES_16BIT_REGSPACING); hw->eeprom_pda = true; #if 0 /* Not in RHEL */ ret = pcmcia_request_irq(link, orinoco_interrupt); #else ret = pcmcia_request_irq(link, &link->irq); #endif if (ret) goto failed; ret = pcmcia_enable_device(link); if (ret) goto failed; /* Reset card */ if (spectrum_cs_hard_reset(priv) != 0) goto failed; /* Initialise the main driver */ if (orinoco_init(priv) != 0) { printk(KERN_ERR PFX "orinoco_init() failed\n"); goto failed; } /* Register an interface with the stack */ #if 0 /* Not in RHEL */ if (orinoco_if_add(priv, link->resource[0]->start, link->irq, NULL) != 0) { #elif 0 /* Not in RHEL */ if (orinoco_if_add(priv, link->io.BasePort1, link->irq, NULL) != 0) { #else if (orinoco_if_add(priv, link->io.BasePort1, link->irq.AssignedIRQ, NULL) != 0) { #endif printk(KERN_ERR PFX "orinoco_if_add() failed\n"); goto failed; } return 0; failed: spectrum_cs_release(link); return -ENODEV; } /* spectrum_cs_config */ static void spectrum_cs_release(struct pcmcia_device *link) { struct orinoco_private *priv = link->priv; unsigned long flags; /* We're committed to taking the device away now, so mark the * hardware as unavailable */ priv->hw.ops->lock_irqsave(&priv->lock, &flags); priv->hw_unavailable++; priv->hw.ops->unlock_irqrestore(&priv->lock, &flags); pcmcia_disable_device(link); if (priv->hw.iobase) ioport_unmap(priv->hw.iobase); } /* spectrum_cs_release */ static int spectrum_cs_suspend(struct pcmcia_device *link) { struct orinoco_private *priv = link->priv; int err = 0; /* Mark the device as stopped, to block IO until later */ orinoco_down(priv); return err; } static int spectrum_cs_resume(struct pcmcia_device *link) { struct orinoco_private *priv = link->priv; int err = orinoco_up(priv); return err; } /********************************************************************/ /* Module initialization */ /********************************************************************/ static struct pcmcia_device_id spectrum_cs_ids[] = { PCMCIA_DEVICE_MANF_CARD(0x026c, 0x0001), /* Symbol Spectrum24 LA4137 */ PCMCIA_DEVICE_MANF_CARD(0x0104, 0x0001), /* Socket Communications CF */ PCMCIA_DEVICE_PROD_ID12("Intel", "PRO/Wireless LAN PC Card", 0x816cc815, 0x6fbf459a), /* 2011B, not 2011 */ PCMCIA_DEVICE_NULL, }; MODULE_DEVICE_TABLE(pcmcia, spectrum_cs_ids); static struct pcmcia_driver orinoco_driver = { .owner = THIS_MODULE, #if 0 /* Not in RHEL */ .name = DRIVER_NAME, #else .drv = { .name = DRIVER_NAME, }, #endif .probe = spectrum_cs_probe, .remove = spectrum_cs_detach, .suspend = spectrum_cs_suspend, .resume = spectrum_cs_resume, .id_table = spectrum_cs_ids, }; static int __init init_spectrum_cs(void) { return pcmcia_register_driver(&orinoco_driver); } static void __exit exit_spectrum_cs(void) { pcmcia_unregister_driver(&orinoco_driver); }
/* * Initialise a card. Mostly similar to PLX code. */ static int orinoco_pci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) { int err = 0; unsigned long pci_iorange; u16 *pci_ioaddr = NULL; unsigned long pci_iolen; struct orinoco_private *priv = NULL; struct net_device *dev = NULL; int netdev_registered = 0; err = pci_enable_device(pdev); if (err) return -EIO; /* Resource 0 is mapped to the hermes registers */ pci_iorange = pci_resource_start(pdev, 0); pci_iolen = pci_resource_len(pdev, 0); pci_ioaddr = ioremap(pci_iorange, pci_iolen); if (! pci_iorange) goto fail; /* Usual setup of structures */ dev = alloc_orinocodev(0, NULL); if (! dev) { err = -ENOMEM; goto fail; } priv = dev->priv; dev->base_addr = (int) pci_ioaddr; dev->mem_start = (unsigned long) pci_iorange; dev->mem_end = ((unsigned long) pci_iorange) + pci_iolen - 1; SET_MODULE_OWNER(dev); printk(KERN_DEBUG "Detected Orinoco/Prism2 PCI device at %s, mem:0x%lX to 0x%lX -> 0x%p, irq:%d\n", pdev->slot_name, dev->mem_start, dev->mem_end, pci_ioaddr, pdev->irq); hermes_struct_init(&(priv->hw), dev->base_addr, HERMES_MEM, HERMES_32BIT_REGSPACING); pci_set_drvdata(pdev, dev); err = request_irq(pdev->irq, orinoco_interrupt, SA_SHIRQ, dev->name, dev); if (err) { printk(KERN_ERR "orinoco_pci: Error allocating IRQ %d.\n", pdev->irq); err = -EBUSY; goto fail; } dev->irq = pdev->irq; /* Perform a COR reset to start the card */ if(orinoco_pci_cor_reset(priv) != 0) { printk(KERN_ERR "%s: Failed to start the card\n", dev->name); err = -ETIMEDOUT; goto fail; } /* Override the normal firmware detection - the Prism 2.5 PCI * cards look like Lucent firmware but are actually Intersil */ priv->firmware_type = FIRMWARE_TYPE_INTERSIL; err = register_netdev(dev); if (err) { printk(KERN_ERR "%s: Failed to register net device\n", dev->name); goto fail; } netdev_registered = 1; return 0; /* succeeded */ fail: if (dev) { if (netdev_registered) unregister_netdev(dev); if (dev->irq) free_irq(dev->irq, dev); kfree(dev); } if (pci_ioaddr) iounmap(pci_ioaddr); return err; }
static int nortel_pci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) { int err; struct orinoco_private *priv; struct nortel_pci_card *card; struct net_device *dev; void __iomem *iomem; err = pci_enable_device(pdev); if (err) { printk(KERN_ERR PFX "Cannot enable PCI device\n"); return err; } err = pci_request_regions(pdev, DRIVER_NAME); if (err != 0) { printk(KERN_ERR PFX "Cannot obtain PCI resources\n"); goto fail_resources; } iomem = pci_iomap(pdev, 2, 0); if (!iomem) { err = -ENOMEM; goto fail_map_io; } /* Allocate network device */ dev = alloc_orinocodev(sizeof(*card), nortel_pci_cor_reset); if (!dev) { printk(KERN_ERR PFX "Cannot allocate network device\n"); err = -ENOMEM; goto fail_alloc; } priv = netdev_priv(dev); card = priv->card; card->iobase1 = pci_resource_start(pdev, 0); card->iobase2 = pci_resource_start(pdev, 1); dev->base_addr = pci_resource_start(pdev, 2); SET_MODULE_OWNER(dev); SET_NETDEV_DEV(dev, &pdev->dev); hermes_struct_init(&priv->hw, iomem, HERMES_16BIT_REGSPACING); printk(KERN_DEBUG PFX "Detected Nortel PCI device at %s irq:%d, " "io addr:0x%lx\n", pci_name(pdev), pdev->irq, dev->base_addr); err = request_irq(pdev->irq, orinoco_interrupt, SA_SHIRQ, dev->name, dev); if (err) { printk(KERN_ERR PFX "Cannot allocate IRQ %d\n", pdev->irq); err = -EBUSY; goto fail_irq; } dev->irq = pdev->irq; err = nortel_pci_hw_init(card); if (err) { printk(KERN_ERR PFX "Hardware initialization failed\n"); goto fail; } err = nortel_pci_cor_reset(priv); if (err) { printk(KERN_ERR PFX "Initial reset failed\n"); goto fail; } err = register_netdev(dev); if (err) { printk(KERN_ERR PFX "Cannot register network device\n"); goto fail; } pci_set_drvdata(pdev, dev); return 0; fail: free_irq(pdev->irq, dev); fail_irq: pci_set_drvdata(pdev, NULL); free_orinocodev(dev); fail_alloc: pci_iounmap(pdev, iomem); fail_map_io: pci_release_regions(pdev); fail_resources: pci_disable_device(pdev); return err; }
static int orinoco_tmd_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) { int err = 0; u32 reg, addr; struct orinoco_private *priv = NULL; unsigned long pccard_ioaddr = 0; unsigned long pccard_iolen = 0; struct net_device *dev = NULL; err = pci_enable_device(pdev); if (err) return -EIO; printk(KERN_DEBUG "TMD setup\n"); pccard_ioaddr = pci_resource_start(pdev, 2); pccard_iolen = pci_resource_len(pdev, 2); if (! request_region(pccard_ioaddr, pccard_iolen, dev_info)) { printk(KERN_ERR "orinoco_tmd: I/O resource at 0x%lx len 0x%lx busy\n", pccard_ioaddr, pccard_iolen); pccard_ioaddr = 0; err = -EBUSY; goto fail; } addr = pci_resource_start(pdev, 1); outb(COR_VALUE, addr); mdelay(1); reg = inb(addr); if (reg != COR_VALUE) { printk(KERN_ERR "orinoco_tmd: Error setting TMD COR values %x should be %x\n", reg, COR_VALUE); err = -EIO; goto fail; } dev = alloc_orinocodev(0, NULL); if (! dev) { err = -ENOMEM; goto fail; } priv = dev->priv; dev->base_addr = pccard_ioaddr; SET_MODULE_OWNER(dev); printk(KERN_DEBUG "Detected Orinoco/Prism2 TMD device at %s irq:%d, io addr:0x%lx\n", pci_name(pdev), pdev->irq, pccard_ioaddr); hermes_struct_init(&(priv->hw), dev->base_addr, HERMES_IO, HERMES_16BIT_REGSPACING); pci_set_drvdata(pdev, dev); err = request_irq(pdev->irq, orinoco_interrupt, SA_SHIRQ, dev->name, dev); if (err) { printk(KERN_ERR "orinoco_tmd: Error allocating IRQ %d.\n", pdev->irq); err = -EBUSY; goto fail; } dev->irq = pdev->irq; err = register_netdev(dev); if (err) goto fail; return 0; /* succeeded */ fail: printk(KERN_DEBUG "orinoco_tmd: init_one(), FAIL!\n"); if (dev) { if (dev->irq) free_irq(dev->irq, dev); kfree(dev); } if (pccard_ioaddr) release_region(pccard_ioaddr, pccard_iolen); pci_disable_device(pdev); return err; }
static int orinoco_nortel_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) { int err; struct orinoco_private *priv; struct orinoco_pci_card *card; struct net_device *dev; void __iomem *hermes_io, *bridge_io, *attr_io; err = pci_enable_device(pdev); if (err) { printk(KERN_ERR PFX "Cannot enable PCI device\n"); return err; } err = pci_request_regions(pdev, DRIVER_NAME); if (err) { printk(KERN_ERR PFX "Cannot obtain PCI resources\n"); goto fail_resources; } bridge_io = pci_iomap(pdev, 0, 0); if (!bridge_io) { printk(KERN_ERR PFX "Cannot map bridge registers\n"); err = -EIO; goto fail_map_bridge; } attr_io = pci_iomap(pdev, 1, 0); if (!attr_io) { printk(KERN_ERR PFX "Cannot map PCMCIA attributes\n"); err = -EIO; goto fail_map_attr; } hermes_io = pci_iomap(pdev, 2, 0); if (!hermes_io) { printk(KERN_ERR PFX "Cannot map chipset registers\n"); err = -EIO; goto fail_map_hermes; } /* Allocate network device */ dev = alloc_orinocodev(sizeof(*card), &pdev->dev, orinoco_nortel_cor_reset, NULL); if (!dev) { printk(KERN_ERR PFX "Cannot allocate network device\n"); err = -ENOMEM; goto fail_alloc; } priv = netdev_priv(dev); card = priv->card; card->bridge_io = bridge_io; card->attr_io = attr_io; SET_NETDEV_DEV(dev, &pdev->dev); hermes_struct_init(&priv->hw, hermes_io, HERMES_16BIT_REGSPACING); err = request_irq(pdev->irq, orinoco_interrupt, IRQF_SHARED, dev->name, dev); if (err) { printk(KERN_ERR PFX "Cannot allocate IRQ %d\n", pdev->irq); err = -EBUSY; goto fail_irq; } err = orinoco_nortel_hw_init(card); if (err) { printk(KERN_ERR PFX "Hardware initialization failed\n"); goto fail; } err = orinoco_nortel_cor_reset(priv); if (err) { printk(KERN_ERR PFX "Initial reset failed\n"); goto fail; } err = register_netdev(dev); if (err) { printk(KERN_ERR PFX "Cannot register network device\n"); goto fail; } pci_set_drvdata(pdev, dev); printk(KERN_DEBUG "%s: " DRIVER_NAME " at %s\n", dev->name, pci_name(pdev)); return 0; fail: free_irq(pdev->irq, dev); fail_irq: pci_set_drvdata(pdev, NULL); free_orinocodev(dev); fail_alloc: pci_iounmap(pdev, hermes_io); fail_map_hermes: pci_iounmap(pdev, attr_io); fail_map_attr: pci_iounmap(pdev, bridge_io); fail_map_bridge: pci_release_regions(pdev); fail_resources: pci_disable_device(pdev); return err; }
static int orinoco_plx_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) { int err = 0; u16 *attr_mem = NULL; u32 reg, addr; struct orinoco_private *priv = NULL; unsigned long pccard_ioaddr = 0; unsigned long pccard_iolen = 0; struct net_device *dev = NULL; int i; err = pci_enable_device(pdev); if (err) return -EIO; /* Resource 2 is mapped to the PCMCIA space */ attr_mem = ioremap(pci_resource_start(pdev, 2), PAGE_SIZE); if (! attr_mem) goto fail; printk(KERN_DEBUG "orinoco_plx: CIS: "); for (i = 0; i < 16; i++) { printk("%02X:", (int)attr_mem[i]); } printk("\n"); /* Verify whether PC card is present */ /* FIXME: we probably need to be smarted about this */ if (memcmp(attr_mem, cis_magic, sizeof(cis_magic)) != 0) { printk(KERN_ERR "orinoco_plx: The CIS value of Prism2 PC card is invalid.\n"); err = -EIO; goto fail; } /* PCMCIA COR is the first byte following CIS: this write should * enable I/O mode and select level-triggered interrupts */ attr_mem[COR_OFFSET] = COR_VALUE; mdelay(1); reg = attr_mem[COR_OFFSET]; if (reg != COR_VALUE) { printk(KERN_ERR "orinoco_plx: Error setting COR value (reg=%x)\n", reg); goto fail; } iounmap(attr_mem); attr_mem = NULL; /* done with this now, it seems */ /* bjoern: We need to tell the card to enable interrupts, in case the serial eprom didn't do this already. See the PLX9052 data book, p8-1 and 8-24 for reference. */ addr = pci_resource_start(pdev, 1); reg = 0; reg = inl(addr+PLX_INTCSR); if (reg & PLX_INTCSR_INTEN) printk(KERN_DEBUG "orinoco_plx: " "Local Interrupt already enabled\n"); else { reg |= PLX_INTCSR_INTEN; outl(reg, addr+PLX_INTCSR); reg = inl(addr+PLX_INTCSR); if(!(reg & PLX_INTCSR_INTEN)) { printk(KERN_ERR "orinoco_plx: " "Couldn't enable Local Interrupts\n"); goto fail; } } /* and 3 to the PCMCIA slot I/O address space */ pccard_ioaddr = pci_resource_start(pdev, 3); pccard_iolen = pci_resource_len(pdev, 3); if (! request_region(pccard_ioaddr, pccard_iolen, DRIVER_NAME)) { printk(KERN_ERR "orinoco_plx: I/O resource 0x%lx @ 0x%lx busy\n", pccard_iolen, pccard_ioaddr); pccard_ioaddr = 0; err = -EBUSY; goto fail; } /* Allocate network device */ dev = alloc_orinocodev(0, NULL); if (! dev) { err = -ENOMEM; goto fail; } priv = netdev_priv(dev); dev->base_addr = pccard_ioaddr; SET_MODULE_OWNER(dev); SET_NETDEV_DEV(dev, &pdev->dev); printk(KERN_DEBUG PFX "Detected Orinoco/Prism2 PLX device " "at %s irq:%d, io addr:0x%lx\n", pci_name(pdev), pdev->irq, pccard_ioaddr); hermes_struct_init(&(priv->hw), dev->base_addr, HERMES_IO, HERMES_16BIT_REGSPACING); pci_set_drvdata(pdev, dev); err = request_irq(pdev->irq, orinoco_interrupt, SA_SHIRQ, dev->name, dev); if (err) { printk(KERN_ERR PFX "Error allocating IRQ %d.\n", pdev->irq); err = -EBUSY; goto fail; } dev->irq = pdev->irq; err = register_netdev(dev); if (err) goto fail; return 0; fail: printk(KERN_DEBUG PFX "init_one(), FAIL!\n"); if (dev) { if (dev->irq) free_irq(dev->irq, dev); free_netdev(dev); } if (pccard_ioaddr) release_region(pccard_ioaddr, pccard_iolen); if (attr_mem) iounmap(attr_mem); pci_disable_device(pdev); return err; }
static int orinoco_plx_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) { int err = 0; u8 __iomem *attr_mem = NULL; u32 csr_reg, plx_addr; struct orinoco_private *priv = NULL; struct orinoco_plx_card *card; unsigned long pccard_ioaddr = 0; unsigned long pccard_iolen = 0; struct net_device *dev = NULL; void __iomem *mem; int i; err = pci_enable_device(pdev); if (err) { printk(KERN_ERR PFX "Cannot enable PCI device\n"); return err; } err = pci_request_regions(pdev, DRIVER_NAME); if (err != 0) { printk(KERN_ERR PFX "Cannot obtain PCI resources\n"); goto fail_resources; } /* Resource 1 is mapped to PLX-specific registers */ plx_addr = pci_resource_start(pdev, 1); /* Resource 2 is mapped to the PCMCIA attribute memory */ attr_mem = ioremap(pci_resource_start(pdev, 2), pci_resource_len(pdev, 2)); if (!attr_mem) { printk(KERN_ERR PFX "Cannot remap PCMCIA space\n"); goto fail_map_attr; } /* Resource 3 is mapped to the PCMCIA I/O address space */ pccard_ioaddr = pci_resource_start(pdev, 3); pccard_iolen = pci_resource_len(pdev, 3); mem = pci_iomap(pdev, 3, 0); if (!mem) { err = -ENOMEM; goto fail_map_io; } /* Allocate network device */ dev = alloc_orinocodev(sizeof(*card), orinoco_plx_cor_reset); if (!dev) { printk(KERN_ERR PFX "Cannot allocate network device\n"); err = -ENOMEM; goto fail_alloc; } priv = netdev_priv(dev); card = priv->card; card->attr_mem = attr_mem; dev->base_addr = pccard_ioaddr; SET_MODULE_OWNER(dev); SET_NETDEV_DEV(dev, &pdev->dev); hermes_struct_init(&priv->hw, mem, HERMES_16BIT_REGSPACING); printk(KERN_DEBUG PFX "Detected Orinoco/Prism2 PLX device " "at %s irq:%d, io addr:0x%lx\n", pci_name(pdev), pdev->irq, pccard_ioaddr); err = request_irq(pdev->irq, orinoco_interrupt, SA_SHIRQ, dev->name, dev); if (err) { printk(KERN_ERR PFX "Cannot allocate IRQ %d\n", pdev->irq); err = -EBUSY; goto fail_irq; } dev->irq = pdev->irq; /* bjoern: We need to tell the card to enable interrupts, in case the serial eprom didn't do this already. See the PLX9052 data book, p8-1 and 8-24 for reference. */ csr_reg = inl(plx_addr + PLX_INTCSR); if (!(csr_reg & PLX_INTCSR_INTEN)) { csr_reg |= PLX_INTCSR_INTEN; outl(csr_reg, plx_addr + PLX_INTCSR); csr_reg = inl(plx_addr + PLX_INTCSR); if (!(csr_reg & PLX_INTCSR_INTEN)) { printk(KERN_ERR PFX "Cannot enable interrupts\n"); goto fail; } } err = orinoco_plx_cor_reset(priv); if (err) { printk(KERN_ERR PFX "Initial reset failed\n"); goto fail; } printk(KERN_DEBUG PFX "CIS: "); for (i = 0; i < 16; i++) { printk("%02X:", readb(attr_mem + 2*i)); } printk("\n"); /* Verify whether a supported PC card is present */ /* FIXME: we probably need to be smarted about this */ for (i = 0; i < sizeof(cis_magic); i++) { if (cis_magic[i] != readb(attr_mem +2*i)) { printk(KERN_ERR PFX "The CIS value of Prism2 PC " "card is unexpected\n"); err = -EIO; goto fail; } } err = register_netdev(dev); if (err) { printk(KERN_ERR PFX "Cannot register network device\n"); goto fail; } pci_set_drvdata(pdev, dev); return 0; fail: free_irq(pdev->irq, dev); fail_irq: pci_set_drvdata(pdev, NULL); free_orinocodev(dev); fail_alloc: pci_iounmap(pdev, mem); fail_map_io: iounmap(attr_mem); fail_map_attr: pci_release_regions(pdev); fail_resources: pci_disable_device(pdev); return err; }
static int airport_attach(struct macio_dev *mdev, const struct of_device_id *match) { struct orinoco_private *priv; struct airport *card; unsigned long phys_addr; hermes_t *hw; if (macio_resource_count(mdev) < 1 || macio_irq_count(mdev) < 1) { printk(KERN_ERR PFX "Wrong interrupt/addresses in OF tree\n"); return -ENODEV; } /* Allocate space for private device-specific data */ priv = alloc_orinocodev(sizeof(*card), &mdev->ofdev.dev, airport_hard_reset, NULL); if (!priv) { printk(KERN_ERR PFX "Cannot allocate network device\n"); return -ENODEV; } card = priv->card; hw = &priv->hw; card->mdev = mdev; if (macio_request_resource(mdev, 0, DRIVER_NAME)) { printk(KERN_ERR PFX "can't request IO resource !\n"); free_orinocodev(priv); return -EBUSY; } macio_set_drvdata(mdev, priv); /* Setup interrupts & base address */ card->irq = macio_irq(mdev, 0); phys_addr = macio_resource_start(mdev, 0); /* Physical address */ printk(KERN_DEBUG PFX "Physical address %lx\n", phys_addr); card->vaddr = ioremap(phys_addr, AIRPORT_IO_LEN); if (!card->vaddr) { printk(KERN_ERR PFX "ioremap() failed\n"); goto failed; } hermes_struct_init(hw, card->vaddr, HERMES_16BIT_REGSPACING); /* Power up card */ pmac_call_feature(PMAC_FTR_AIRPORT_ENABLE, macio_get_of_node(mdev), 0, 1); ssleep(1); /* Reset it before we get the interrupt */ hermes_init(hw); if (request_irq(card->irq, orinoco_interrupt, 0, DRIVER_NAME, priv)) { printk(KERN_ERR PFX "Couldn't get IRQ %d\n", card->irq); goto failed; } card->irq_requested = 1; /* Initialise the main driver */ if (orinoco_init(priv) != 0) { printk(KERN_ERR PFX "orinoco_init() failed\n"); goto failed; } /* Register an interface with the stack */ if (orinoco_if_add(priv, phys_addr, card->irq) != 0) { printk(KERN_ERR PFX "orinoco_if_add() failed\n"); goto failed; } card->ndev_registered = 1; return 0; failed: airport_detach(mdev); return -ENODEV; } /* airport_attach */
static dldwd_priv_t* airport_attach(struct device_node* of_node) { dldwd_priv_t *priv; struct net_device *ndev; dldwd_card_t* card; hermes_t *hw; TRACE_ENTER("dldwd"); if (of_node->n_addrs < 1 || of_node->n_intrs < 1) { printk(KERN_ERR "airport: wrong interrupt/addresses in OF tree\n"); return NULL; } /* Allocate space for private device-specific data */ card = kmalloc(sizeof(*card), GFP_KERNEL); if (!card) { printk(KERN_ERR "airport: can't allocate device datas\n"); return NULL; } memset(card, 0, sizeof(*card)); priv = &(card->priv); priv->card = card; ndev = &priv->ndev; hw = &priv->hw; card->node = of_node; /* Setup the common part */ if (dldwd_setup(priv) < 0) { kfree(card); return NULL; } /* Overrides */ ndev->init = airport_init; ndev->open = airport_open; ndev->stop = airport_stop; /* Setup interrupts & base address */ ndev->irq = of_node->intrs[0].line; ndev->base_addr = (unsigned long)ioremap(of_node->addrs[0].address, 0x1000) - _IO_BASE; hermes_struct_init(hw, ndev->base_addr); /* Power up card */ feature_set_airport_power(card->node, 1); current->state = TASK_UNINTERRUPTIBLE; schedule_timeout(HZ); /* Reset it before we get the interrupt */ hermes_reset(hw); if (request_irq(ndev->irq, dldwd_interrupt, 0, "Airport", (void *)priv)) { printk(KERN_ERR "airport: Couldn't get IRQ %d\n", ndev->irq); goto failed; } card->irq_requested = 1; /* register_netdev will give us an ethX name */ ndev->name[0] = '\0'; /* Tell the stack we exist */ if (register_netdev(ndev) != 0) { printk(KERN_ERR "airport: register_netdev() failed\n"); goto failed; } printk(KERN_DEBUG "airport: card registered for interface %s\n", ndev->name); card->ndev_registered = 1; SET_MODULE_OWNER(ndev); /* And give us the proc nodes for debugging */ if (dldwd_proc_dev_init(priv) != 0) printk(KERN_ERR "airport: Failed to create /proc node for %s\n", ndev->name); #ifdef CONFIG_PMAC_PBOOK pmu_register_sleep_notifier(&airport_sleep_notifier); #endif return priv; failed: airport_detach(priv); return NULL; } /* airport_attach */
static void orinoco_cs_config(dev_link_t * link) { client_handle_t handle = link->handle; struct orinoco_private *priv = link->priv; struct orinoco_pccard *card = (struct orinoco_pccard *)priv->card; hermes_t *hw = &priv->hw; struct net_device *ndev = &priv->ndev; tuple_t tuple; cisparse_t parse; int last_fn, last_ret; u_char buf[64]; config_info_t conf; cistpl_cftable_entry_t dflt = { 0 }; cisinfo_t info; TRACE_ENTER("orinoco"); CS_CHECK(ValidateCIS, handle, &info); /* This reads the card's CONFIG tuple to find its configuration registers. */ tuple.DesiredTuple = CISTPL_CONFIG; tuple.Attributes = 0; tuple.TupleData = buf; tuple.TupleDataMax = sizeof(buf); tuple.TupleOffset = 0; CS_CHECK(GetFirstTuple, handle, &tuple); CS_CHECK(GetTupleData, handle, &tuple); CS_CHECK(ParseTuple, handle, &tuple, &parse); link->conf.ConfigBase = parse.config.base; link->conf.Present = parse.config.rmask[0]; /* Configure card */ link->state |= DEV_CONFIG; /* Look up the current Vcc */ CS_CHECK(GetConfigurationInfo, handle, &conf); link->conf.Vcc = conf.Vcc; DEBUG(0, "orinoco_cs_config: ConfigBase = 0x%x link->conf.Vcc = %d\n", link->conf.ConfigBase, link->conf.Vcc); /* In this loop, we scan the CIS for configuration table entries, each of which describes a valid card configuration, including voltage, IO window, memory window, and interrupt settings. We make no assumptions about the card to be configured: we use just the information available in the CIS. In an ideal world, this would work for any PCMCIA card, but it requires a complete and accurate CIS. In practice, a driver usually "knows" most of these things without consulting the CIS, and most client drivers will only use the CIS to fill in implementation-defined details. */ tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY; CS_CHECK(GetFirstTuple, handle, &tuple); while (1) { cistpl_cftable_entry_t *cfg = &(parse.cftable_entry); CFG_CHECK(GetTupleData, handle, &tuple); CFG_CHECK(ParseTuple, handle, &tuple, &parse); DEBUG(0, "orinoco_cs_config: index = 0x%x, flags = 0x%x\n", cfg->index, cfg->flags); if (cfg->flags & CISTPL_CFTABLE_DEFAULT) dflt = *cfg; if (cfg->index == 0) goto next_entry; link->conf.ConfigIndex = cfg->index; /* Does this card need audio output? */ if (cfg->flags & CISTPL_CFTABLE_AUDIO) { link->conf.Attributes |= CONF_ENABLE_SPKR; link->conf.Status = CCSR_AUDIO_ENA; } /* Use power settings for Vcc and Vpp if present */ /* Note that the CIS values need to be rescaled */ if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) { if (conf.Vcc != cfg->vcc.param[CISTPL_POWER_VNOM] / 10000) { DEBUG(2, "orinoco_cs_config: Vcc mismatch (conf.Vcc = %d, CIS = %d)\n", conf.Vcc, cfg->vcc.param[CISTPL_POWER_VNOM] / 10000); if(!ignore_cis_vcc) goto next_entry; } } else if (dflt.vcc.present & (1 << CISTPL_POWER_VNOM)) { if (conf.Vcc != dflt.vcc.param[CISTPL_POWER_VNOM] / 10000) { DEBUG(2, "orinoco_cs_config: Vcc mismatch (conf.Vcc = %d, CIS = %d)\n", conf.Vcc, dflt.vcc.param[CISTPL_POWER_VNOM] / 10000); if(!ignore_cis_vcc) goto next_entry; } } if (cfg->vpp1.present & (1 << CISTPL_POWER_VNOM)) link->conf.Vpp1 = link->conf.Vpp2 = cfg->vpp1.param[CISTPL_POWER_VNOM] / 10000; else if (dflt.vpp1.present & (1 << CISTPL_POWER_VNOM)) link->conf.Vpp1 = link->conf.Vpp2 = dflt.vpp1.param[CISTPL_POWER_VNOM] / 10000; DEBUG(0, "orinoco_cs_config: We seem to have configured Vcc and Vpp\n"); /* Do we need to allocate an interrupt? */ if (cfg->irq.IRQInfo1 || dflt.irq.IRQInfo1) link->conf.Attributes |= CONF_ENABLE_IRQ; /* IO window settings */ link->io.NumPorts1 = link->io.NumPorts2 = 0; if ((cfg->io.nwin > 0) || (dflt.io.nwin > 0)) { cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt.io; link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO; if (!(io->flags & CISTPL_IO_8BIT)) link->io.Attributes1 = IO_DATA_PATH_WIDTH_16; if (!(io->flags & CISTPL_IO_16BIT)) link->io.Attributes1 = IO_DATA_PATH_WIDTH_8; link->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK; link->io.BasePort1 = io->win[0].base; link->io.NumPorts1 = io->win[0].len; if (io->nwin > 1) { link->io.Attributes2 = link->io.Attributes1; link->io.BasePort2 = io->win[1].base; link->io.NumPorts2 = io->win[1].len; } /* This reserves IO space but doesn't actually enable it */ CFG_CHECK(RequestIO, link->handle, &link->io); } /* If we got this far, we're cool! */ break; next_entry: if (link->io.NumPorts1) CardServices(ReleaseIO, link->handle, &link->io); CS_CHECK(GetNextTuple, handle, &tuple); } /* Allocate an interrupt line. Note that this does not assign a handler to the interrupt, unless the 'Handler' member of the irq structure is initialized. */ if (link->conf.Attributes & CONF_ENABLE_IRQ) { int i; link->irq.Attributes = IRQ_TYPE_EXCLUSIVE | IRQ_HANDLE_PRESENT; link->irq.IRQInfo1 = IRQ_INFO2_VALID | IRQ_LEVEL_ID; if (irq_list[0] == -1) link->irq.IRQInfo2 = irq_mask; else for (i=0; i<4; i++) link->irq.IRQInfo2 |= 1 << irq_list[i]; link->irq.Handler = orinoco_interrupt; link->irq.Instance = priv; CS_CHECK(RequestIRQ, link->handle, &link->irq); } /* We initialize the hermes structure before completing PCMCIA configuration just in case the interrupt handler gets called. */ hermes_struct_init(hw, link->io.BasePort1); /* This actually configures the PCMCIA socket -- setting up the I/O windows and the interrupt mapping, and putting the card and host interface into "Memory and IO" mode. */ CS_CHECK(RequestConfiguration, link->handle, &link->conf); ndev->base_addr = link->io.BasePort1; ndev->irq = link->irq.AssignedIRQ; /* register_netdev will give us an ethX name */ ndev->name[0] = '\0'; /* Tell the stack we exist */ if (register_netdev(ndev) != 0) { printk(KERN_ERR "orinoco_cs: register_netdev() failed\n"); goto failed; } strcpy(card->node.dev_name, ndev->name); /* Finally, report what we've done */ printk(KERN_DEBUG "%s: index 0x%02x: Vcc %d.%d", ndev->name, link->conf.ConfigIndex, link->conf.Vcc / 10, link->conf.Vcc % 10); if (link->conf.Vpp1) printk(", Vpp %d.%d", link->conf.Vpp1 / 10, link->conf.Vpp1 % 10); if (link->conf.Attributes & CONF_ENABLE_IRQ) printk(", irq %d", link->irq.AssignedIRQ); if (link->io.NumPorts1) printk(", io 0x%04x-0x%04x", link->io.BasePort1, link->io.BasePort1 + link->io.NumPorts1 - 1); if (link->io.NumPorts2) printk(" & 0x%04x-0x%04x", link->io.BasePort2, link->io.BasePort2 + link->io.NumPorts2 - 1); printk("\n"); /* And give us the proc nodes for debugging */ if (orinoco_proc_dev_init(priv) != 0) { printk(KERN_ERR "orinoco_cs: Failed to create /proc node for %s\n", ndev->name); goto failed; } /* Note to myself : this replace MOD_INC_USE_COUNT/MOD_DEC_USE_COUNT */ SET_MODULE_OWNER(ndev); /* Allow cor_reset, /proc & ioctls to act */ priv->hw_ready = 1; /* Do a Pcmcia soft reset of the card (optional) */ if(reset_cor) orinoco_cs_cor_reset(priv); /* At this point, the dev_node_t structure(s) need to be initialized and arranged in a linked list at link->dev. */ card->node.major = card->node.minor = 0; link->dev = &card->node; link->state &= ~DEV_CONFIG_PENDING; TRACE_EXIT("orinoco"); return; cs_failed: cs_error(link->handle, last_fn, last_ret); failed: orinoco_cs_release((u_long) link); TRACE_EXIT("orinoco"); } /* orinoco_cs_config */
static int orinoco_pci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) { int err; struct orinoco_private *priv; struct orinoco_pci_card *card; void __iomem *hermes_io; err = pci_enable_device(pdev); if (err) { printk(KERN_ERR PFX "Cannot enable PCI device\n"); return err; } err = pci_request_regions(pdev, DRIVER_NAME); if (err) { printk(KERN_ERR PFX "Cannot obtain PCI resources\n"); goto fail_resources; } hermes_io = pci_iomap(pdev, 0, 0); if (!hermes_io) { printk(KERN_ERR PFX "Cannot remap chipset registers\n"); err = -EIO; goto fail_map_hermes; } /* Allocate network device */ priv = alloc_orinocodev(sizeof(*card), &pdev->dev, orinoco_pci_cor_reset, NULL); if (!priv) { printk(KERN_ERR PFX "Cannot allocate network device\n"); err = -ENOMEM; goto fail_alloc; } card = priv->card; hermes_struct_init(&priv->hw, hermes_io, HERMES_32BIT_REGSPACING); err = request_irq(pdev->irq, orinoco_interrupt, IRQF_SHARED, DRIVER_NAME, priv); if (err) { printk(KERN_ERR PFX "Cannot allocate IRQ %d\n", pdev->irq); err = -EBUSY; goto fail_irq; } err = orinoco_pci_cor_reset(priv); if (err) { printk(KERN_ERR PFX "Initial reset failed\n"); goto fail; } err = orinoco_init(priv); if (err) { printk(KERN_ERR PFX "orinoco_init() failed\n"); goto fail; } err = orinoco_if_add(priv, 0, 0, NULL); if (err) { printk(KERN_ERR PFX "orinoco_if_add() failed\n"); goto fail_wiphy; } pci_set_drvdata(pdev, priv); return 0; fail_wiphy: wiphy_unregister(priv_to_wiphy(priv)); fail: free_irq(pdev->irq, priv); fail_irq: free_orinocodev(priv); fail_alloc: pci_iounmap(pdev, hermes_io); fail_map_hermes: pci_release_regions(pdev); fail_resources: pci_disable_device(pdev); return err; }
static void orinoco_cs_config(dev_link_t *link) { struct net_device *dev = link->priv; client_handle_t handle = link->handle; struct orinoco_private *priv = netdev_priv(dev); struct orinoco_pccard *card = priv->card; hermes_t *hw = &priv->hw; int last_fn, last_ret; u_char buf[64]; config_info_t conf; cisinfo_t info; tuple_t tuple; cisparse_t parse; void __iomem *mem; CS_CHECK(ValidateCIS, pcmcia_validate_cis(handle, &info)); /* * This reads the card's CONFIG tuple to find its * configuration registers. */ tuple.DesiredTuple = CISTPL_CONFIG; tuple.Attributes = 0; tuple.TupleData = buf; tuple.TupleDataMax = sizeof(buf); tuple.TupleOffset = 0; CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(handle, &tuple)); CS_CHECK(GetTupleData, pcmcia_get_tuple_data(handle, &tuple)); CS_CHECK(ParseTuple, pcmcia_parse_tuple(handle, &tuple, &parse)); link->conf.ConfigBase = parse.config.base; link->conf.Present = parse.config.rmask[0]; /* Configure card */ link->state |= DEV_CONFIG; /* Look up the current Vcc */ CS_CHECK(GetConfigurationInfo, pcmcia_get_configuration_info(handle, &conf)); link->conf.Vcc = conf.Vcc; /* * In this loop, we scan the CIS for configuration table * entries, each of which describes a valid card * configuration, including voltage, IO window, memory window, * and interrupt settings. * * We make no assumptions about the card to be configured: we * use just the information available in the CIS. In an ideal * world, this would work for any PCMCIA card, but it requires * a complete and accurate CIS. In practice, a driver usually * "knows" most of these things without consulting the CIS, * and most client drivers will only use the CIS to fill in * implementation-defined details. */ tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY; CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(handle, &tuple)); while (1) { cistpl_cftable_entry_t *cfg = &(parse.cftable_entry); cistpl_cftable_entry_t dflt = { .index = 0 }; if ( (pcmcia_get_tuple_data(handle, &tuple) != 0) || (pcmcia_parse_tuple(handle, &tuple, &parse) != 0)) goto next_entry; if (cfg->flags & CISTPL_CFTABLE_DEFAULT) dflt = *cfg; if (cfg->index == 0) goto next_entry; link->conf.ConfigIndex = cfg->index; /* Does this card need audio output? */ if (cfg->flags & CISTPL_CFTABLE_AUDIO) { link->conf.Attributes |= CONF_ENABLE_SPKR; link->conf.Status = CCSR_AUDIO_ENA; } /* Use power settings for Vcc and Vpp if present */ /* Note that the CIS values need to be rescaled */ if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) { if (conf.Vcc != cfg->vcc.param[CISTPL_POWER_VNOM] / 10000) { DEBUG(2, "orinoco_cs_config: Vcc mismatch (conf.Vcc = %d, CIS = %d)\n", conf.Vcc, cfg->vcc.param[CISTPL_POWER_VNOM] / 10000); if (!ignore_cis_vcc) goto next_entry; } } else if (dflt.vcc.present & (1 << CISTPL_POWER_VNOM)) { if (conf.Vcc != dflt.vcc.param[CISTPL_POWER_VNOM] / 10000) { DEBUG(2, "orinoco_cs_config: Vcc mismatch (conf.Vcc = %d, CIS = %d)\n", conf.Vcc, dflt.vcc.param[CISTPL_POWER_VNOM] / 10000); if(!ignore_cis_vcc) goto next_entry; } } if (cfg->vpp1.present & (1 << CISTPL_POWER_VNOM)) link->conf.Vpp1 = link->conf.Vpp2 = cfg->vpp1.param[CISTPL_POWER_VNOM] / 10000; else if (dflt.vpp1.present & (1 << CISTPL_POWER_VNOM)) link->conf.Vpp1 = link->conf.Vpp2 = dflt.vpp1.param[CISTPL_POWER_VNOM] / 10000; /* Do we need to allocate an interrupt? */ link->conf.Attributes |= CONF_ENABLE_IRQ; /* IO window settings */ link->io.NumPorts1 = link->io.NumPorts2 = 0; if ((cfg->io.nwin > 0) || (dflt.io.nwin > 0)) { cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt.io; link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO; if (!(io->flags & CISTPL_IO_8BIT)) link->io.Attributes1 = IO_DATA_PATH_WIDTH_16; if (!(io->flags & CISTPL_IO_16BIT)) link->io.Attributes1 = IO_DATA_PATH_WIDTH_8; link->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK; link->io.BasePort1 = io->win[0].base; link->io.NumPorts1 = io->win[0].len; if (io->nwin > 1) { link->io.Attributes2 = link->io.Attributes1; link->io.BasePort2 = io->win[1].base; link->io.NumPorts2 = io->win[1].len; } /* This reserves IO space but doesn't actually enable it */ if (pcmcia_request_io(link->handle, &link->io) != 0) goto next_entry; } /* If we got this far, we're cool! */ break; next_entry: if (link->io.NumPorts1) pcmcia_release_io(link->handle, &link->io); last_ret = pcmcia_get_next_tuple(handle, &tuple); if (last_ret == CS_NO_MORE_ITEMS) { printk(KERN_ERR PFX "GetNextTuple(): No matching " "CIS configuration. Maybe you need the " "ignore_cis_vcc=1 parameter.\n"); goto cs_failed; } } /* * Allocate an interrupt line. Note that this does not assign * a handler to the interrupt, unless the 'Handler' member of * the irq structure is initialized. */ CS_CHECK(RequestIRQ, pcmcia_request_irq(link->handle, &link->irq)); /* We initialize the hermes structure before completing PCMCIA * configuration just in case the interrupt handler gets * called. */ mem = ioport_map(link->io.BasePort1, link->io.NumPorts1); if (!mem) goto cs_failed; hermes_struct_init(hw, mem, HERMES_16BIT_REGSPACING); /* * This actually configures the PCMCIA socket -- setting up * the I/O windows and the interrupt mapping, and putting the * card and host interface into "Memory and IO" mode. */ CS_CHECK(RequestConfiguration, pcmcia_request_configuration(link->handle, &link->conf)); /* Ok, we have the configuration, prepare to register the netdev */ dev->base_addr = link->io.BasePort1; dev->irq = link->irq.AssignedIRQ; SET_MODULE_OWNER(dev); card->node.major = card->node.minor = 0; SET_NETDEV_DEV(dev, &handle_to_dev(handle)); /* Tell the stack we exist */ if (register_netdev(dev) != 0) { printk(KERN_ERR PFX "register_netdev() failed\n"); goto failed; } /* At this point, the dev_node_t structure(s) needs to be * initialized and arranged in a linked list at link->dev. */ strcpy(card->node.dev_name, dev->name); link->dev = &card->node; /* link->dev being non-NULL is also used to indicate that the net_device has been registered */ link->state &= ~DEV_CONFIG_PENDING; /* Finally, report what we've done */ printk(KERN_DEBUG "%s: index 0x%02x: Vcc %d.%d", dev->name, link->conf.ConfigIndex, link->conf.Vcc / 10, link->conf.Vcc % 10); if (link->conf.Vpp1) printk(", Vpp %d.%d", link->conf.Vpp1 / 10, link->conf.Vpp1 % 10); printk(", irq %d", link->irq.AssignedIRQ); if (link->io.NumPorts1) printk(", io 0x%04x-0x%04x", link->io.BasePort1, link->io.BasePort1 + link->io.NumPorts1 - 1); if (link->io.NumPorts2) printk(" & 0x%04x-0x%04x", link->io.BasePort2, link->io.BasePort2 + link->io.NumPorts2 - 1); printk("\n"); return; cs_failed: cs_error(link->handle, last_fn, last_ret); failed: orinoco_cs_release(link); } /* orinoco_cs_config */ /* * After a card is removed, orinoco_cs_release() will unregister the * device, and release the PCMCIA configuration. If the device is * still open, this will be postponed until it is closed. */ static void orinoco_cs_release(dev_link_t *link) { struct net_device *dev = link->priv; struct orinoco_private *priv = netdev_priv(dev); unsigned long flags; /* We're committed to taking the device away now, so mark the * hardware as unavailable */ spin_lock_irqsave(&priv->lock, flags); priv->hw_unavailable++; spin_unlock_irqrestore(&priv->lock, flags); /* Don't bother checking to see if these succeed or not */ pcmcia_release_configuration(link->handle); if (link->io.NumPorts1) pcmcia_release_io(link->handle, &link->io); if (link->irq.AssignedIRQ) pcmcia_release_irq(link->handle, &link->irq); link->state &= ~DEV_CONFIG; if (priv->hw.iobase) ioport_unmap(priv->hw.iobase); } /* orinoco_cs_release */ /* * The card status event handler. Mostly, this schedules other stuff * to run after an event is received. */ static int orinoco_cs_event(event_t event, int priority, event_callback_args_t * args) { dev_link_t *link = args->client_data; struct net_device *dev = link->priv; struct orinoco_private *priv = netdev_priv(dev); struct orinoco_pccard *card = priv->card; int err = 0; unsigned long flags; switch (event) { case CS_EVENT_CARD_REMOVAL: link->state &= ~DEV_PRESENT; if (link->state & DEV_CONFIG) { unsigned long flags; spin_lock_irqsave(&priv->lock, flags); netif_device_detach(dev); priv->hw_unavailable++; spin_unlock_irqrestore(&priv->lock, flags); } break; case CS_EVENT_CARD_INSERTION: link->state |= DEV_PRESENT | DEV_CONFIG_PENDING; orinoco_cs_config(link); break; case CS_EVENT_PM_SUSPEND: link->state |= DEV_SUSPEND; /* Fall through... */ case CS_EVENT_RESET_PHYSICAL: /* Mark the device as stopped, to block IO until later */ if (link->state & DEV_CONFIG) { /* This is probably racy, but I can't think of a better way, short of rewriting the PCMCIA layer to not suck :-( */ if (! test_bit(0, &card->hard_reset_in_progress)) { spin_lock_irqsave(&priv->lock, flags); err = __orinoco_down(dev); if (err) printk(KERN_WARNING "%s: %s: Error %d downing interface\n", dev->name, event == CS_EVENT_PM_SUSPEND ? "SUSPEND" : "RESET_PHYSICAL", err); netif_device_detach(dev); priv->hw_unavailable++; spin_unlock_irqrestore(&priv->lock, flags); } pcmcia_release_configuration(link->handle); } break; case CS_EVENT_PM_RESUME: link->state &= ~DEV_SUSPEND; /* Fall through... */ case CS_EVENT_CARD_RESET: if (link->state & DEV_CONFIG) { /* FIXME: should we double check that this is * the same card as we had before */ pcmcia_request_configuration(link->handle, &link->conf); if (! test_bit(0, &card->hard_reset_in_progress)) { err = orinoco_reinit_firmware(dev); if (err) { printk(KERN_ERR "%s: Error %d re-initializing firmware\n", dev->name, err); break; } spin_lock_irqsave(&priv->lock, flags); netif_device_attach(dev); priv->hw_unavailable--; if (priv->open && ! priv->hw_unavailable) { err = __orinoco_up(dev); if (err) printk(KERN_ERR "%s: Error %d restarting card\n", dev->name, err); } spin_unlock_irqrestore(&priv->lock, flags); } } break; } return err; } /* orinoco_cs_event */
static int orinoco_plx_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) { int err = 0; u16 *attr_mem = NULL; u32 reg, addr; struct orinoco_private *priv = NULL; unsigned long pccard_ioaddr = 0; unsigned long pccard_iolen = 0; struct net_device *dev = NULL; int netdev_registered = 0; int i; TRACE_ENTER("orinoco_plx"); err = pci_enable_device(pdev); if (err) return -EIO; /* Resource 2 is mapped to the PCMCIA space */ attr_mem = ioremap(pci_resource_start(pdev, 2), PAGE_SIZE); if (! attr_mem) goto fail; printk(KERN_DEBUG "orinoco_plx: CIS: "); for (i = 0; i < 16; i++) { printk("%02X:", (int)attr_mem[i]); } printk("\n"); /* Verify whether PC card is present */ /* FIXME: we probably need to be smarted about this */ if (memcmp(attr_mem, cis_magic, sizeof(cis_magic)) != 0) { printk(KERN_ERR "orinoco_plx: The CIS value of Prism2 PC card is invalid.\n"); err = -EIO; goto fail; } /* PCMCIA COR is the first byte following CIS: this write should * enable I/O mode and select level-triggered interrupts */ attr_mem[COR_OFFSET] = COR_VALUE; mdelay(1); reg = attr_mem[COR_OFFSET]; if (reg != COR_VALUE) { printk(KERN_ERR "orinoco_plx: Error setting COR value (reg=%x)\n", reg); goto fail; } iounmap(attr_mem); attr_mem = NULL; /* done with this now, it seems */ /* bjoern: We need to tell the card to enable interrupts, in case the serial eprom didn't do this already. See the PLX9052 data book, p8-1 and 8-24 for reference. */ addr = pci_resource_start(pdev, 1); reg = 0; reg = inl(addr+PLX_INTCSR); if(reg & PLX_INTCSR_INTEN) printk(KERN_DEBUG "orinoco_plx: " "Local Interrupt already enabled\n"); else { reg |= PLX_INTCSR_INTEN; outl(reg, addr+PLX_INTCSR); reg = inl(addr+PLX_INTCSR); if(!(reg & PLX_INTCSR_INTEN)) { printk(KERN_ERR "orinoco_plx: " "Couldn't enable Local Interrupts\n"); goto fail; } } /* and 3 to the PCMCIA slot I/O address space */ pccard_ioaddr = pci_resource_start(pdev, 3); pccard_iolen = pci_resource_len(pdev, 3); if (! request_region(pccard_ioaddr, pccard_iolen, dev_info)) { printk(KERN_ERR "orinoco_plx: I/O resource 0x%lx @ 0x%lx busy\n", pccard_iolen, pccard_ioaddr); pccard_ioaddr = 0; err = -EBUSY; goto fail; } priv = kmalloc(sizeof(*priv), GFP_KERNEL); if (! priv) { err = -ENOMEM; goto fail; } memset(priv, 0, sizeof(*priv)); dev = &priv->ndev; err = orinoco_setup(priv); if (err) goto fail; dev->base_addr = pccard_ioaddr; dev->open = orinoco_plx_open; dev->stop = orinoco_plx_stop; priv->card_reset_handler = NULL; /* We have no reset handler */ SET_MODULE_OWNER(dev); printk(KERN_DEBUG "Detected Orinoco/Prism2 PLX device at %s irq:%d, io addr:0x%lx\n", pdev->slot_name, pdev->irq, pccard_ioaddr); hermes_struct_init(&(priv->hw), dev->base_addr); pci_set_drvdata(pdev, priv); err = request_irq(pdev->irq, orinoco_plx_interrupt, SA_SHIRQ, dev->name, priv); if (err) { printk(KERN_ERR "orinoco_plx: Error allocating IRQ %d.\n", pdev->irq); err = -EBUSY; goto fail; } dev->irq = pdev->irq; err = register_netdev(dev); if (err) goto fail; netdev_registered = 1; err = orinoco_proc_dev_init(priv); if (err) goto fail; priv->hw_ready = 1; TRACE_EXIT("orinoco_plx"); return 0; /* succeeded */ fail: printk(KERN_DEBUG "orinoco_plx: init_one(), FAIL!\n"); if (priv) { orinoco_proc_dev_cleanup(priv); if (netdev_registered) unregister_netdev(dev); if (dev->irq) free_irq(dev->irq, priv); kfree(priv); } if (pccard_ioaddr) release_region(pccard_ioaddr, pccard_iolen); if (attr_mem) iounmap(attr_mem); pci_disable_device(pdev); TRACE_EXIT("orinoco_plx"); return err; }
static int orinoco_cs_config(struct pcmcia_device *link) { struct orinoco_private *priv = link->priv; struct hermes *hw = &priv->hw; int ret; void __iomem *mem; #if 0 /* Not in RHEL */ link->config_flags |= CONF_AUTO_SET_VPP | CONF_AUTO_CHECK_VCC | CONF_AUTO_SET_IO | CONF_ENABLE_IRQ; if (ignore_cis_vcc) link->config_flags &= ~CONF_AUTO_CHECK_VCC; #endif ret = pcmcia_loop_config(link, orinoco_cs_config_check, NULL); if (ret) { if (!ignore_cis_vcc) printk(KERN_ERR PFX "GetNextTuple(): No matching " "CIS configuration. Maybe you need the " "ignore_cis_vcc=1 parameter.\n"); goto failed; } #if 0 /* Not in RHEL */ mem = ioport_map(link->resource[0]->start, resource_size(link->resource[0])); #else mem = ioport_map(link->io.BasePort1, link->io.NumPorts1); #endif if (!mem) goto failed; /* We initialize the hermes structure before completing PCMCIA * configuration just in case the interrupt handler gets * called. */ hermes_struct_init(hw, mem, HERMES_16BIT_REGSPACING); #if 0 /* Not in RHEL */ ret = pcmcia_request_irq(link, orinoco_interrupt); #else ret = pcmcia_request_irq(link, &link->irq); #endif if (ret) goto failed; ret = pcmcia_enable_device(link); if (ret) goto failed; /* Initialise the main driver */ if (orinoco_init(priv) != 0) { printk(KERN_ERR PFX "orinoco_init() failed\n"); goto failed; } /* Register an interface with the stack */ #if 0 /* Not in RHEL */ if (orinoco_if_add(priv, link->resource[0]->start, link->irq, NULL) != 0) { #elif 0 /* Not in RHEL */ if (orinoco_if_add(priv, link->io.BasePort1, link->irq, NULL) != 0) { #else if (orinoco_if_add(priv, link->io.BasePort1, link->irq.AssignedIRQ, NULL) != 0) { #endif printk(KERN_ERR PFX "orinoco_if_add() failed\n"); goto failed; } return 0; failed: orinoco_cs_release(link); return -ENODEV; } /* orinoco_cs_config */ static void orinoco_cs_release(struct pcmcia_device *link) { struct orinoco_private *priv = link->priv; unsigned long flags; /* We're committed to taking the device away now, so mark the * hardware as unavailable */ priv->hw.ops->lock_irqsave(&priv->lock, &flags); priv->hw_unavailable++; priv->hw.ops->unlock_irqrestore(&priv->lock, &flags); pcmcia_disable_device(link); if (priv->hw.iobase) ioport_unmap(priv->hw.iobase); } /* orinoco_cs_release */ static int orinoco_cs_suspend(struct pcmcia_device *link) { struct orinoco_private *priv = link->priv; struct orinoco_pccard *card = priv->card; /* This is probably racy, but I can't think of a better way, short of rewriting the PCMCIA layer to not suck :-( */ if (!test_bit(0, &card->hard_reset_in_progress)) orinoco_down(priv); return 0; } static int orinoco_cs_resume(struct pcmcia_device *link) { struct orinoco_private *priv = link->priv; struct orinoco_pccard *card = priv->card; int err = 0; if (!test_bit(0, &card->hard_reset_in_progress)) err = orinoco_up(priv); return err; } /********************************************************************/ /* Module initialization */ /********************************************************************/ static struct pcmcia_device_id orinoco_cs_ids[] = { PCMCIA_DEVICE_MANF_CARD(0x0101, 0x0777), /* 3Com AirConnect PCI 777A */ PCMCIA_DEVICE_MANF_CARD(0x016b, 0x0001), /* Ericsson WLAN Card C11 */ PCMCIA_DEVICE_MANF_CARD(0x01eb, 0x080a), /* Nortel Networks eMobility 802.11 Wireless Adapter */ PCMCIA_DEVICE_MANF_CARD(0x0261, 0x0002), /* AirWay 802.11 Adapter (PCMCIA) */ PCMCIA_DEVICE_MANF_CARD(0x0268, 0x0001), /* ARtem Onair */ PCMCIA_DEVICE_MANF_CARD(0x0268, 0x0003), /* ARtem Onair Comcard 11 */ PCMCIA_DEVICE_MANF_CARD(0x026f, 0x0305), /* Buffalo WLI-PCM-S11 */ PCMCIA_DEVICE_MANF_CARD(0x02aa, 0x0002), /* ASUS SpaceLink WL-100 */ PCMCIA_DEVICE_MANF_CARD(0x02ac, 0x0002), /* SpeedStream SS1021 Wireless Adapter */ PCMCIA_DEVICE_MANF_CARD(0x02ac, 0x3021), /* SpeedStream Wireless Adapter */ PCMCIA_DEVICE_MANF_CARD(0x14ea, 0xb001), /* PLANEX RoadLannerWave GW-NS11H */ PCMCIA_DEVICE_PROD_ID12("3Com", "3CRWE737A AirConnect Wireless LAN PC Card", 0x41240e5b, 0x56010af3), PCMCIA_DEVICE_PROD_ID12("Allied Telesyn", "AT-WCL452 Wireless PCMCIA Radio", 0x5cd01705, 0x4271660f), PCMCIA_DEVICE_PROD_ID12("ASUS", "802_11B_CF_CARD_25", 0x78fc06ee, 0x45a50c1e), PCMCIA_DEVICE_PROD_ID12("ASUS", "802_11b_PC_CARD_25", 0x78fc06ee, 0xdb9aa842), PCMCIA_DEVICE_PROD_ID12("Avaya Communication", "Avaya Wireless PC Card", 0xd8a43b78, 0x0d341169), PCMCIA_DEVICE_PROD_ID12("BENQ", "AWL100 PCMCIA ADAPTER", 0x35dadc74, 0x01f7fedb), PCMCIA_DEVICE_PROD_ID12("Cabletron", "RoamAbout 802.11 DS", 0x32d445f5, 0xedeffd90), PCMCIA_DEVICE_PROD_ID12("D-Link Corporation", "D-Link DWL-650H 11Mbps WLAN Adapter", 0xef544d24, 0xcd8ea916), PCMCIA_DEVICE_PROD_ID12("ELSA", "AirLancer MC-11", 0x4507a33a, 0xef54f0e3), PCMCIA_DEVICE_PROD_ID12("HyperLink", "Wireless PC Card 11Mbps", 0x56cc3f1a, 0x0bcf220c), PCMCIA_DEVICE_PROD_ID12("Intel", "PRO/Wireless 2011 LAN PC Card", 0x816cc815, 0x07f58077), PCMCIA_DEVICE_PROD_ID12("LeArtery", "SYNCBYAIR 11Mbps Wireless LAN PC Card", 0x7e3b326a, 0x49893e92), PCMCIA_DEVICE_PROD_ID12("Lucent Technologies", "WaveLAN/IEEE", 0x23eb9949, 0xc562e72a), PCMCIA_DEVICE_PROD_ID12("MELCO", "WLI-PCM-L11", 0x481e0094, 0x7360e410), PCMCIA_DEVICE_PROD_ID12("MELCO", "WLI-PCM-L11G", 0x481e0094, 0xf57ca4b3), PCMCIA_DEVICE_PROD_ID12("NCR", "WaveLAN/IEEE", 0x24358cd4, 0xc562e72a), PCMCIA_DEVICE_PROD_ID12("Nortel Networks", "emobility 802.11 Wireless LAN PC Card", 0x2d617ea0, 0x88cd5767), PCMCIA_DEVICE_PROD_ID12("OTC", "Wireless AirEZY 2411-PCC WLAN Card", 0x4ac44287, 0x235a6bed), PCMCIA_DEVICE_PROD_ID12("PROXIM", "LAN PC CARD HARMONY 80211B", 0xc6536a5e, 0x090c3cd9), PCMCIA_DEVICE_PROD_ID12("PROXIM", "LAN PCI CARD HARMONY 80211B", 0xc6536a5e, 0x9f494e26), PCMCIA_DEVICE_PROD_ID12("SAMSUNG", "11Mbps WLAN Card", 0x43d74cb4, 0x579bd91b), PCMCIA_DEVICE_PROD_ID12("Symbol Technologies", "LA4111 Spectrum24 Wireless LAN PC Card", 0x3f02b4d6, 0x3663cb0e), PCMCIA_DEVICE_MANF_CARD_PROD_ID3(0x0156, 0x0002, "Version 01.01", 0xd27deb1a), /* Lucent Orinoco */ #ifdef CONFIG_HERMES_PRISM /* Only entries that certainly identify Prism chipset */ PCMCIA_DEVICE_MANF_CARD(0x000b, 0x7100), /* SonicWALL Long Range Wireless Card */ PCMCIA_DEVICE_MANF_CARD(0x000b, 0x7300), /* Sohoware NCP110, Philips 802.11b */ PCMCIA_DEVICE_MANF_CARD(0x0089, 0x0002), /* AnyPoint(TM) Wireless II PC Card */ PCMCIA_DEVICE_MANF_CARD(0x0126, 0x8000), /* PROXIM RangeLAN-DS/LAN PC CARD */ PCMCIA_DEVICE_MANF_CARD(0x0138, 0x0002), /* Compaq WL100 11 Mbps Wireless Adapter */ PCMCIA_DEVICE_MANF_CARD(0x01ff, 0x0008), /* Intermec MobileLAN 11Mbps 802.11b WLAN Card */ PCMCIA_DEVICE_MANF_CARD(0x0250, 0x0002), /* Samsung SWL2000-N 11Mb/s WLAN Card */ PCMCIA_DEVICE_MANF_CARD(0x0274, 0x1612), /* Linksys WPC11 Version 2.5 */ PCMCIA_DEVICE_MANF_CARD(0x0274, 0x1613), /* Linksys WPC11 Version 3 */ PCMCIA_DEVICE_MANF_CARD(0x028a, 0x0002), /* Compaq HNW-100 11 Mbps Wireless Adapter */ PCMCIA_DEVICE_MANF_CARD(0x028a, 0x0673), /* Linksys WCF12 Wireless CompactFlash Card */ PCMCIA_DEVICE_MANF_CARD(0x50c2, 0x7300), /* Airvast WN-100 */ PCMCIA_DEVICE_MANF_CARD(0x9005, 0x0021), /* Adaptec Ultra Wireless ANW-8030 */ PCMCIA_DEVICE_MANF_CARD(0xc001, 0x0008), /* CONTEC FLEXSCAN/FX-DDS110-PCC */ PCMCIA_DEVICE_MANF_CARD(0xc250, 0x0002), /* Conceptronic CON11Cpro, EMTAC A2424i */ PCMCIA_DEVICE_MANF_CARD(0xd601, 0x0002), /* Safeway 802.11b, ZCOMAX AirRunner/XI-300 */ PCMCIA_DEVICE_MANF_CARD(0xd601, 0x0005), /* D-Link DCF660, Sandisk Connect SDWCFB-000 */ PCMCIA_DEVICE_PROD_ID123("Instant Wireless ", " Network PC CARD", "Version 01.02", 0x11d901af, 0x6e9bd926, 0x4b74baa0), PCMCIA_DEVICE_PROD_ID12("ACTIONTEC", "PRISM Wireless LAN PC Card", 0x393089da, 0xa71e69d5), PCMCIA_DEVICE_PROD_ID12("Addtron", "AWP-100 Wireless PCMCIA", 0xe6ec52ce, 0x08649af2), PCMCIA_DEVICE_PROD_ID12("BUFFALO", "WLI-CF-S11G", 0x2decece3, 0x82067c18), PCMCIA_DEVICE_PROD_ID12("BUFFALO", "WLI-PCM-L11G", 0x2decece3, 0xf57ca4b3), PCMCIA_DEVICE_PROD_ID12("Compaq", "WL200_11Mbps_Wireless_PCI_Card", 0x54f7c49c, 0x15a75e5b), PCMCIA_DEVICE_PROD_ID12("corega K.K.", "Wireless LAN PCC-11", 0x5261440f, 0xa6405584), PCMCIA_DEVICE_PROD_ID12("corega K.K.", "Wireless LAN PCCA-11", 0x5261440f, 0xdf6115f9), PCMCIA_DEVICE_PROD_ID12("corega_K.K.", "Wireless_LAN_PCCB-11", 0x29e33311, 0xee7a27ae), PCMCIA_DEVICE_PROD_ID12("Digital Data Communications", "WPC-0100", 0xfdd73470, 0xe0b6f146), PCMCIA_DEVICE_PROD_ID12("D", "Link DRC-650 11Mbps WLAN Card", 0x71b18589, 0xf144e3ac), PCMCIA_DEVICE_PROD_ID12("D", "Link DWL-650 11Mbps WLAN Card", 0x71b18589, 0xb6f1b0ab), PCMCIA_DEVICE_PROD_ID12(" ", "IEEE 802.11 Wireless LAN/PC Card", 0x3b6e20c8, 0xefccafe9), PCMCIA_DEVICE_PROD_ID12("INTERSIL", "HFA384x/IEEE", 0x74c5e40d, 0xdb472a18), PCMCIA_DEVICE_PROD_ID12("INTERSIL", "I-GATE 11M PC Card / PC Card plus", 0x74c5e40d, 0x8304ff77), PCMCIA_DEVICE_PROD_ID12("Intersil", "PRISM 2_5 PCMCIA ADAPTER", 0x4b801a17, 0x6345a0bf), PCMCIA_DEVICE_PROD_ID12("Linksys", "Wireless CompactFlash Card", 0x0733cc81, 0x0c52f395), PCMCIA_DEVICE_PROD_ID12("Microsoft", "Wireless Notebook Adapter MN-520", 0x5961bf85, 0x6eec8c01), PCMCIA_DEVICE_PROD_ID12("NETGEAR MA401RA Wireless PC", "Card", 0x0306467f, 0x9762e8f1), PCMCIA_DEVICE_PROD_ID12("NETGEAR MA401 Wireless PC", "Card", 0xa37434e9, 0x9762e8f1), PCMCIA_DEVICE_PROD_ID12("OEM", "PRISM2 IEEE 802.11 PC-Card", 0xfea54c90, 0x48f2bdd6), PCMCIA_DEVICE_PROD_ID12("PLANEX", "GeoWave/GW-CF110", 0x209f40ab, 0xd9715264), PCMCIA_DEVICE_PROD_ID12("PLANEX", "GeoWave/GW-NS110", 0x209f40ab, 0x46263178), PCMCIA_DEVICE_PROD_ID12("SMC", "SMC2532W-B EliteConnect Wireless Adapter", 0xc4f8b18b, 0x196bd757), PCMCIA_DEVICE_PROD_ID12("SMC", "SMC2632W", 0xc4f8b18b, 0x474a1f2a), PCMCIA_DEVICE_PROD_ID12("ZoomAir 11Mbps High", "Rate wireless Networking", 0x273fe3db, 0x32a1eaee), PCMCIA_DEVICE_PROD_ID3("HFA3863", 0x355cb092), PCMCIA_DEVICE_PROD_ID3("ISL37100P", 0x630d52b2), PCMCIA_DEVICE_PROD_ID3("ISL37101P-10", 0xdd97a26b), PCMCIA_DEVICE_PROD_ID3("ISL37300P", 0xc9049a39), /* This may be Agere or Intersil Firmware */ PCMCIA_DEVICE_MANF_CARD(0x0156, 0x0002), #endif PCMCIA_DEVICE_NULL, }; MODULE_DEVICE_TABLE(pcmcia, orinoco_cs_ids); static struct pcmcia_driver orinoco_driver = { .owner = THIS_MODULE, #if 0 /* Not in RHEL */ .name = DRIVER_NAME, #else .drv = { .name = DRIVER_NAME, }, #endif .probe = orinoco_cs_probe, .remove = orinoco_cs_detach, .id_table = orinoco_cs_ids, .suspend = orinoco_cs_suspend, .resume = orinoco_cs_resume, }; static int __init init_orinoco_cs(void) { return pcmcia_register_driver(&orinoco_driver); } static void __exit exit_orinoco_cs(void) { pcmcia_unregister_driver(&orinoco_driver); }