/**
* @brief This function initializes the USB controller in host mode and
* the associated variables.
*
* This function enables the USB controller for host mode operation.
*
* @param none
*
* @return none
*
*/
void usb_host_task_init(void)
{
Pll_start_auto();
Wait_pll_ready();
Usb_disable();
Usb_enable();
Usb_unfreeze_clock();
Usb_attach();
Usb_enable_uvcon_pin();
Usb_select_host();
Usb_disable_vbus_hw_control(); // Force Vbus generation without timeout
Host_enable_device_disconnection_interrupt();
device_state=DEVICE_UNATTACHED;
init_usb_tree();
}
__interrupt void usb_general_interrupt()
#endif
{
#if (USB_HOST_PIPE_INTERRUPT_TRANSFER == ENABLE)
U8 i;
U8 save_pipe_nb;
#endif
// ---------- DEVICE events management -----------------------------------
#if (USB_DEVICE_FEATURE == ENABLED)
// - Device start of frame received
if (Is_usb_sof() && Is_sof_interrupt_enabled())
{
Usb_ack_sof();
Usb_sof_action();
}
#ifdef WA_USB_SUSPEND_PERTUBATION
// - Device Suspend event (no more USB activity detected)
if (Is_usb_suspend() && Is_suspend_interrupt_enabled())
{
usb_suspended=TRUE;
Usb_ack_wake_up(); // clear wake up to detect next event
Usb_send_event(EVT_USB_SUSPEND);
Usb_ack_suspend();
Usb_enable_wake_up_interrupt();
Usb_disable_resume_interrupt();
Usb_freeze_clock();
Stop_pll();
Usb_suspend_action();
}
// - Wake up event (USB activity detected): Used to resume
if (Is_usb_wake_up() && Is_wake_up_interrupt_enabled())
{
if(Is_pll_ready()==FALSE)
{
Pll_start_auto();
Wait_pll_ready();
}
Usb_unfreeze_clock();
Usb_ack_wake_up();
if(usb_suspended)
{
Usb_enable_resume_interrupt();
Usb_enable_reset_interrupt();
while(Is_usb_wake_up())
{
Usb_ack_wake_up();
}
usb_delay_ms(2);
if(Is_usb_sof() || Is_usb_resume() || Is_usb_reset() )
{
Usb_disable_wake_up_interrupt();
Usb_wake_up_action();
Usb_send_event(EVT_USB_WAKE_UP);
Usb_enable_suspend_interrupt();
Usb_enable_resume_interrupt();
Usb_enable_reset_interrupt();
}
else // Workarround to make the USB enter power down mode again (spurious transcient detected on the USB lines)
{
Usb_ack_wake_up(); // clear wake up to detect next event
Usb_send_event(EVT_USB_SUSPEND);
Usb_enable_wake_up_interrupt();
Usb_disable_resume_interrupt();
Usb_freeze_clock();
Stop_pll();
Usb_suspend_action();
}
}
}
// - Resume state bus detection
if (Is_usb_resume() && Is_resume_interrupt_enabled())
{
usb_suspended = FALSE;
Usb_disable_wake_up_interrupt();
Usb_ack_resume();
Usb_disable_resume_interrupt();
Usb_resume_action();
Usb_send_event(EVT_USB_RESUME);
}
#else
// - Device Suspend event (no more USB activity detected)
if (Is_usb_suspend() && Is_suspend_interrupt_enabled())
{
// Remote wake-up handler
if ((remote_wakeup_feature == ENABLED) && (usb_configuration_nb != 0))
{
Usb_disable_suspend_interrupt();
Usb_ack_wake_up();
Usb_enable_wake_up_interrupt();
Stop_pll();
Usb_freeze_clock();
Usb_suspend_action();
// After that user can execute "Usb_initiate_remote_wake_up()" to initiate a remote wake-up
// Note that the suspend interrupt flag SUSPI must still be set to enable upstream resume
// So the SUSPE enable bit must be cleared to avoid redundant interrupt
// ****************
// Please note also that is Vbus is lost during an upstream resume (Host disconnection),
// the RMWKUP bit (used to initiate remote wake up and that is normally cleared by hardware when sent)
// remains set after the event, so that a good way to handle this feature is :
// Usb_unfreeze_clock();
// Usb_initiate_remote_wake_up();
// while (Is_usb_pending_remote_wake_up())
// {
// if (Is_usb_vbus_low())
// {
// // Emergency action (reset macro, etc.) if Vbus lost during resuming
// break;
// }
// }
// Usb_ack_remote_wake_up_start();
// ****************
}
else
{
// No remote wake-up supported
Usb_ack_wake_up(); // clear wake up to detect next event
Usb_send_event(EVT_USB_SUSPEND);
Usb_ack_suspend(); // must be executed last (after Usb_suspend_action()) to allow upstream resume
Usb_enable_wake_up_interrupt();
Usb_freeze_clock();
Stop_pll();
Usb_suspend_action();
}
}
// - Wake up event (USB activity detected): Used to resume
if (Is_usb_wake_up() && Is_wake_up_interrupt_enabled())
{
if(Is_pll_ready()==FALSE)
{
Pll_start_auto();
Wait_pll_ready();
}
Usb_unfreeze_clock();
Usb_ack_wake_up();
Usb_disable_wake_up_interrupt();
Usb_wake_up_action();
Usb_send_event(EVT_USB_WAKE_UP);
Usb_enable_suspend_interrupt();
}
// - Resume state bus detection
if (Is_usb_resume() && Is_resume_interrupt_enabled())
{
Usb_disable_wake_up_interrupt();
Usb_ack_resume();
Usb_disable_resume_interrupt();
Usb_resume_action();
Usb_send_event(EVT_USB_RESUME);
}
#endif
// - USB bus reset detection
if (Is_usb_reset()&& Is_reset_interrupt_enabled())
{
Usb_ack_reset();
usb_init_device();
Usb_reset_action();
Usb_send_event(EVT_USB_RESET);
}
#endif// End DEVICE FEATURE MODE
// ---------- HOST events management -----------------------------------
#if (USB_HOST_FEATURE == ENABLED && USB_DEVICE_FEATURE == ENABLED)
// - ID pin change detection
if(Is_usb_id_transition()&&Is_usb_id_interrupt_enabled())
{
if(Is_usb_id_device())
{ g_usb_mode=USB_MODE_DEVICE;}
else
{ g_usb_mode=USB_MODE_HOST;}
Usb_ack_id_transition();
if( g_usb_mode != g_old_usb_mode) // Basic Debounce
{
if(Is_usb_id_device()) // Going to device mode
{
Usb_send_event(EVT_USB_DEVICE_FUNCTION);
}
else // Going to host mode
{
Usb_send_event(EVT_USB_HOST_FUNCTION);
}
Usb_id_transition_action();
LOG_STR_CODE(log_id_change);
#if ( ID_PIN_CHANGE_GENERATE_RESET == ENABLE)
// Hot ID transition generates wdt reset
wdtdrv_enable(WDTO_16MS);
while(1);
#endif
}
}
#endif
#if (USB_HOST_FEATURE == ENABLED)
// - The device has been disconnected
if(Is_device_disconnection() && Is_host_device_disconnection_interrupt_enabled())
{
host_disable_all_pipe();
Host_ack_device_disconnection();
device_state=DEVICE_DISCONNECTED;
Usb_send_event(EVT_HOST_DISCONNECTION);
init_usb_tree();
LOG_STR_CODE(log_device_disconnect);
Host_device_disconnection_action();
}
// - Device connection
if(Is_device_connection() && Is_host_device_connection_interrupt_enabled())
{
Host_ack_device_connection();
host_disable_all_pipe();
Host_device_connection_action();
}
// - Host Start of frame has been sent
if (Is_host_sof() && Is_host_sof_interrupt_enabled())
{
Host_ack_sof();
Usb_send_event(EVT_HOST_SOF);
private_sof_counter++;
#if (USB_HUB_SUPPORT==ENABLE)
hub_interrupt_sof++;
#endif
// delay timeout management for interrupt tranfer mode in host mode
#if ((USB_HOST_PIPE_INTERRUPT_TRANSFER==ENABLE) && (TIMEOUT_DELAY_ENABLE==ENABLE))
if (private_sof_counter>=250) // Count 1/4 sec
{
private_sof_counter=0;
for(i=0;i<MAX_EP_NB;i++)
{
if(it_pipe_str[i].enable==ENABLE)
{
save_pipe_nb=Host_get_selected_pipe();
Host_select_pipe(i);
if((++it_pipe_str[i].timeout>TIMEOUT_DELAY) && (Host_get_pipe_type()!=TYPE_INTERRUPT))
{
it_pipe_str[i].enable=DISABLE;
it_pipe_str[i].status=PIPE_DELAY_TIMEOUT;
Host_stop_pipe_interrupt(i);
if (is_any_interrupt_pipe_active()==FALSE) // If no more transfer is armed
{
if (g_sav_int_sof_enable==FALSE)
{
Host_disable_sof_interrupt();
}
}
it_pipe_str[i].handle(PIPE_DELAY_TIMEOUT,it_pipe_str[i].nb_byte_processed);
}
Host_select_pipe(save_pipe_nb);
}
}
}
#endif // (USB_HOST_PIPE_INTERRUPT_TRANSFER==ENABLE) && (TIMEOUT_DELAY_ENABLE==ENABLE))
Host_sof_action();
}
// - Host Wake-up has been received
if (Is_host_hwup() && Is_host_hwup_interrupt_enabled())
{
Host_disable_hwup_interrupt(); // Wake up interrupt should be disable host is now wake up !
// CAUTION HWUP can be cleared only when USB clock is active (not frozen)!
Pll_start_auto(); // First Restart the PLL for USB operation
Wait_pll_ready(); // Get sure pll is lock
Usb_unfreeze_clock(); // Enable clock on USB interface
Host_ack_hwup(); // Clear HWUP interrupt flag
Usb_send_event(EVT_HOST_HWUP); // Send software event
Host_hwup_action(); // Map custom action
}
#endif // End HOST FEATURE MODE
}
