void MyMIWI_Init(void) {
// Configure Pins for MRF24J40MB
mPORTESetBits(RST_MIWI);
mPORTESetPinsDigitalOut(RST_MIWI);
mPORTBSetBits(MIWI_WAKE);
mPORTBSetPinsDigitalOut(MIWI_WAKE);
// Configure the INT3 controller for MIWI
// Set RD10/INT3 as input
mPORTDSetPinsDigitalIn(BIT_10);
// Clear corresponding bits in INTCON for falling edge trigger
INTCONCLR = _INTCON_INT3EP_MASK;
// Set up interrupt prioirty and sub-priority
INTSetVectorPriority(INT_EXTERNAL_3_VECTOR, My_INT_EXTERNAL_3_PRIORITY);
INTSetVectorSubPriority(INT_EXTERNAL_3_VECTOR, My_INT_EXTERNAL_3_SUB_PRIORITY);
// Clear the interrupt flags
INTClearFlag(INT_INT3);
// Enable INT3
INTEnable(INT_INT3, INT_ENABLED);
// WARNING : Change in file MRF24J40.c in Microchip Application Library
// the line : void __ISR(_EXTERNAL_1_VECTOR, ipl4) _INT1Interrupt(void)
// by : void __ISR(_EXTERNAL_3_VECTOR, ipl4) _INT3Interrupt(void)
}
void MyWIFI_Init(void) {
// Configure Pins for MRF24J40MB
mPORTESetBits(RST_WIFI);
mPORTESetPinsDigitalOut(RST_WIFI);
mPORTBSetBits(WIFI_HIB);
mPORTBSetPinsDigitalOut(WIFI_HIB);
mPORTBClearBits(WIFI_WP); // Has to be pulled low
mPORTBSetPinsDigitalOut(WIFI_WP);
/*
// Configure the INT4 controller for WIFI
// Set RD11/INT4 as input
mPORTDSetPinsDigitalIn(BIT_11);
// Clear corresponding bits in INTCON for falling edge trigger
INTCONCLR = _INTCON_INT4EP_MASK;
// Set up interrupt prioirty and sub-priority
INTSetVectorPriority(INT_EXTERNAL_4_VECTOR, My_INT_EXTERNAL_4_PRIORITY);
INTSetVectorSubPriority(INT_EXTERNAL_4_VECTOR, My_INT_EXTERNAL_4_SUB_PRIORITY);
// Clear the interrupt flags
INTClearFlag(INT_INT4);
// Enable INT4
INTEnable(INT_INT4, INT_ENABLED);
*/
}
void lcdconfig()
{
PORTSetPinsDigitalOut(IOPORT_D,BIT_4 | BIT_5);
mPORTESetPinsDigitalOut(BIT_0 | BIT_1 | BIT_2 | BIT_3 | BIT_4 | BIT_5 | BIT_6 | BIT_7);
lcdcmnd(0x38); //init lcd 2 line 5x7 matrix
delay(10);
lcdcmnd(0x0E); //display on cursor blink
delay(10);
lcdcmnd(0x01); // clear display
delay(10);
lcdcmnd(0x06); // shift cursor right
delay(10);
lcdcmnd(0x84); // cursor at line 1 pos. 4
delay(10);
}
void lcdini()
{
mPORTESetPinsDigitalOut(BIT_0 | BIT_1 | BIT_2 | BIT_3 | BIT_4 | BIT_5 | BIT_6 | BIT_7);
PORTSetPinsDigitalOut(IOPORT_D,BIT_5 | BIT_4);
lcdcmd(0x38);
msdelay(10);
lcdcmd(0x0E);
msdelay(10);
lcdcmd(0x01);
msdelay(10);
lcdcmd(0x06);
msdelay(10);
lcdcmd(0x80);
return;
}
void InitializeSystem()
{
SYSTEMConfigWaitStatesAndPB(CLOCK_FREQ);
mOSCSetPBDIV(OSC_PB_DIV_4); // Set to get 20MHz PB clock
//mOSCSetPBDIV(OSC_PB_DIV_2);
CheKseg0CacheOn();
mJTAGPortEnable(0);
// Initialize the pins to all digital output and driven to ground.
// Exception is RE7 and RE6 which are switch inputs
PORTSetPinsDigitalIn(IOPORT_E, BIT_6);
PORTSetPinsDigitalIn(IOPORT_E, BIT_7);
mPORTASetPinsDigitalOut(0xFFFF);
mPORTBSetPinsDigitalOut(0xFFFF);
mPORTCSetPinsDigitalOut(0xFFFF);
mPORTDSetPinsDigitalOut(0xFFFF);
mPORTESetPinsDigitalOut(0xFF3F);
mPORTFSetPinsDigitalOut(0xFFFF);
mPORTGSetPinsDigitalOut(0xFFFF);
mPORTAClearBits(0xFFFF);
mPORTBClearBits(0xFFFF);
mPORTCClearBits(0xFFFF);
mPORTDClearBits(0xFFFF);
mPORTEClearBits(0xFF3F);
mPORTESetBits(0x000F); // LED latches need to be set high for off
mPORTFClearBits(0xFFFF);
mPORTGClearBits(0xFFFF);
INTEnableSystemMultiVectoredInt();
#ifdef SANITY_CHECK
mLED_Green_On();
#endif
//LCD_Initialize();
//WIFI_Initialize();
//SPRINKLER_Initialize();
//RTCC_Initialize();
//SERIALUSB_Initialize();
SDCARD_Initialize();
TCPIP_Initialize();
}
int main(void)
{
//LOCALS
unsigned int temp;
unsigned int channel1, channel2;
M1_stepPeriod = M2_stepPeriod = M3_stepPeriod = M4_stepPeriod = 50; // in tens of u-seconds
unsigned char M1_state = 0, M2_state = 0, M3_state = 0, M4_state = 0;
SYSTEMConfig(GetSystemClock(), SYS_CFG_WAIT_STATES | SYS_CFG_PCACHE);
/* TIMER1 - now configured to interrupt at 10 khz (every 100us) */
OpenTimer1(T1_ON | T1_SOURCE_INT | T1_PS_1_1, T1_TICK);
ConfigIntTimer1(T1_INT_ON | T1_INT_PRIOR_2);
/* TIMER2 - 100 khz interrupt for distance measure*/
OpenTimer2(T2_ON | T2_SOURCE_INT | T2_PS_1_1, T2_TICK);
ConfigIntTimer2(T2_INT_ON | T2_INT_PRIOR_3); //It is off until trigger
/* PORTA b2 and b3 for servo-PWM */
mPORTAClearBits(BIT_2 | BIT_3);
mPORTASetPinsDigitalOut(BIT_2 | BIT_3);
/* ULTRASONICS: some bits of PORTB for ultrasonic sensors */
PORTResetPins(IOPORT_B, BIT_8 | BIT_9| BIT_10 | BIT_11 );
PORTSetPinsDigitalOut(IOPORT_B, BIT_8 | BIT_9| BIT_10 | BIT_11); //trigger
/* Input Capture pins for echo signals */
//interrupt on every risging/falling edge starting with a rising edge
PORTSetPinsDigitalIn(IOPORT_D, BIT_8| BIT_9| BIT_10| BIT_11); //INC1, INC2, INC3, INC4 Pin
mIC1ClearIntFlag();
OpenCapture1( IC_EVERY_EDGE | IC_INT_1CAPTURE | IC_TIMER2_SRC | IC_ON );//front
ConfigIntCapture1(IC_INT_ON | IC_INT_PRIOR_4 | IC_INT_SUB_PRIOR_3);
OpenCapture2( IC_EVERY_EDGE | IC_INT_1CAPTURE | IC_TIMER2_SRC | IC_ON );//back
ConfigIntCapture2(IC_INT_ON | IC_INT_PRIOR_4 | IC_INT_SUB_PRIOR_3);
OpenCapture3( IC_EVERY_EDGE | IC_INT_1CAPTURE | IC_TIMER2_SRC | IC_ON );//left
ConfigIntCapture3(IC_INT_ON | IC_INT_PRIOR_4 | IC_INT_SUB_PRIOR_3);
OpenCapture4( IC_EVERY_EDGE | IC_INT_1CAPTURE | IC_TIMER2_SRC | IC_ON );//right
ConfigIntCapture4(IC_INT_ON | IC_INT_PRIOR_4 | IC_INT_SUB_PRIOR_3);
/* PINS used for the START (RD13) BUTTON */
PORTSetPinsDigitalIn(IOPORT_D, BIT_13);
#define CONFIG (CN_ON | CN_IDLE_CON)
#define INTERRUPT (CHANGE_INT_ON | CHANGE_INT_PRI_2)
mCNOpen(CONFIG, CN19_ENABLE, CN19_PULLUP_ENABLE);
temp = mPORTDRead();
/* PORT D and E for motors */
//motor 1
mPORTDSetBits(BIT_4 | BIT_5 | BIT_6 | BIT_7); // Turn on PORTD on startup.
mPORTDSetPinsDigitalOut(BIT_4 | BIT_5 | BIT_6 | BIT_7); // Make PORTD output.
//motor 2
mPORTCSetBits(BIT_1 | BIT_2 | BIT_3 | BIT_4); // Turn on PORTC on startup.
mPORTCSetPinsDigitalOut(BIT_1 | BIT_2 | BIT_3 | BIT_4); // Make PORTC output.
//motor 3 and 4
mPORTESetBits(BIT_0 | BIT_1 | BIT_2 | BIT_3 |
BIT_4 | BIT_5 | BIT_6 | BIT_7); // Turn on PORTE on startup.
mPORTESetPinsDigitalOut(BIT_0 | BIT_1 | BIT_2 | BIT_3 |
BIT_4 | BIT_5 | BIT_6 | BIT_7); // Make PORTE output.
// UART2 to connect to the PC.
// This initialization assumes 36MHz Fpb clock. If it changes,
// you will have to modify baud rate initializer.
UARTConfigure(UART2, UART_ENABLE_PINS_TX_RX_ONLY);
UARTSetFifoMode(UART2, UART_INTERRUPT_ON_TX_NOT_FULL | UART_INTERRUPT_ON_RX_NOT_EMPTY);
UARTSetLineControl(UART2, UART_DATA_SIZE_8_BITS | UART_PARITY_NONE | UART_STOP_BITS_1);
UARTSetDataRate(UART2, GetPeripheralClock(), BAUD);
UARTEnable(UART2, UART_ENABLE_FLAGS(UART_PERIPHERAL | UART_RX | UART_TX));
// Configure UART2 RX Interrupt
INTEnable(INT_SOURCE_UART_RX(UART2), INT_ENABLED);
INTSetVectorPriority(INT_VECTOR_UART(UART2), INT_PRIORITY_LEVEL_2);
INTSetVectorSubPriority(INT_VECTOR_UART(UART2), INT_SUB_PRIORITY_LEVEL_0);
/* PORTD for LEDs - DEBUGGING */
mPORTDClearBits(BIT_0 | BIT_1 | BIT_2);
mPORTDSetPinsDigitalOut(BIT_0 | BIT_1 | BIT_2);
// Congifure Change/Notice Interrupt Flag
ConfigIntCN(INTERRUPT);
// configure for multi-vectored mode
INTConfigureSystem(INT_SYSTEM_CONFIG_MULT_VECTOR);
// enable interrupts
INTEnableInterrupts();
counterDistanceMeasure=600; //measure ULTRASONICS distance each 60 ms
while (1) {
/***************** Robot MAIN state machine *****************/
unsigned char ret = 0;
switch (Robo_State) {
case 0:
MotorsON = 0;
Robo_State = 0;
InvInitialOrientation(RESET);
TestDog(RESET);
GoToRoom4short(RESET);
BackToStart(RESET);
InitialOrientation(RESET);
GoToCenter(RESET);
GoToRoom4long(RESET);
break;
case 1:
ret = InvInitialOrientation(GO);
if (ret == 1) {
Robo_State = 2;
}
break;
case 2:
ret = TestDog(GO);
if (ret == 1) {
Robo_State = 3; //DOG not found
} else if (ret == 2) {
Robo_State = 4; //DOG found
}
break;
case 3:
ret = GoToRoom4short(GO);
if (ret == 1) {
Robo_State = 0;
}
break;
case 4:
ret = BackToStart(GO);
if (ret == 1) {
Robo_State = 5;
}
break;
case 5:
ret = GoToCenter(GO);
if (ret == 1) {
Robo_State = 6;
}
break;
case 6:
ret = GoToRoom4long(GO);
if (ret == 1) {
Robo_State = 0;
}
break;
}
if (frontDistance < 30 || backDistance < 30 || leftDistance < 30 || rightDistance < 30)
mPORTDSetBits(BIT_0);
else
mPORTDClearBits(BIT_0);
/***************************************************************/
/***************** Motors State Machine ************************/
if (MotorsON) {
/****************************
MOTOR MAP
M1 O-------------O M2 ON EVEN MOTORS, STEPS MUST BE INVERTED
| /\ | i.e. FORWARD IS BACKWARD
| / \ |
| || |
| || |
M3 O-------------O M4
*****************************/
if (M1_counter == 0) {
switch (M1_state) {
case 0: // set 0011
step (0x3 , 1);
if (M1forward)
M1_state = 1;
else
M1_state = 3;
break;
case 1: // set 1001
step (0x9 , 1);
if (M1forward)
M1_state = 2;
else
M1_state = 0;
break;
case 2: // set 1100
step (0xC , 1);
if (M1forward)
M1_state = 3;
else
M1_state = 1;
break;
case 3: // set 0110
default:
step (0x6 , 1);
if (M1forward)
M1_state = 0;
else
M1_state = 2;
break;
}
M1_counter = M1_stepPeriod;
step_counter[0]--;
if (directionNow == countingDirection)
step_counter[1]--;
}
if (M2_counter == 0) {
switch (M2_state) {
case 0: // set 0011
step (0x3 , 2);
if (M2forward)
M2_state = 1;
else
M2_state = 3;
break;
case 1: // set 0110
step (0x6 , 2);
if (M2forward)
M2_state = 2;
else
M2_state = 0;
break;
case 2: // set 1100
step (0xC , 2);
if (M2forward)
M2_state = 3;
else
M2_state = 1;
break;
case 3: // set 1001
default:
step (0x9 , 2);
if (M2forward)
M2_state = 0;
else
M2_state = 2;
break;
}
M2_counter = M2_stepPeriod;
}
if (M3_counter == 0) {
switch (M3_state) {
case 0: // set 0011
step (0x3 , 3);
if (M3forward)
M3_state = 1;
else
M3_state = 3;
break;
case 1: // set 1001
step (0x9 , 3);
if (M3forward)
M3_state = 2;
else
M3_state = 0;
break;
case 2: // set 1100
step (0xC , 3);
if (M3forward)
M3_state = 3;
else
M3_state = 1;
break;
case 3: // set 0110
default:
step (0x6 , 3);
if (M3forward)
M3_state = 0;
else
M3_state = 2;
break;
}
M3_counter = M3_stepPeriod;
}
if (M4_counter == 0) {
switch (M4_state) {
case 0: // set 0011
step (0x3 , 4);
if (M4forward)
M4_state = 1;
else
M4_state = 3;
break;
case 1: // set 0110
step (0x6 , 4);
if (M4forward)
M4_state = 2;
else
M4_state = 0;
break;
case 2: // set 1100
step (0xC , 4);
if (M4forward)
M4_state = 3;
else
M4_state = 1;
break;
case 3: // set 1001
default:
step (0x9 , 4);
if (M4forward)
M4_state = 0;
else
M4_state = 2;
break;
}
M4_counter = M4_stepPeriod;
}
} else {
//motors off
mPORTDSetBits(BIT_4 | BIT_5 | BIT_6 | BIT_7);
mPORTCSetBits(BIT_1 | BIT_2 | BIT_3 | BIT_4);
mPORTESetBits(BIT_0 | BIT_1 | BIT_2 | BIT_3 |
BIT_4 | BIT_5 | BIT_6 | BIT_7);
}
/************************************************************/
/******* TEST CODE, toggles the servos (from 90 deg. to -90 deg.) every 1 s. ********/
/* if (auxcounter == 0) {
servo1_angle = 0;
if (servo2_angle == 90)
servo2_angle = -90;
else
servo2_angle = 90;
auxcounter = 20000; // toggle angle every 2 s.
}
*/
servo1_angle = 0;
servo2_angle = -90;
/*
if (frontDistance > 13 && frontDistance < 17) {
servo2_angle = 90;
}
else
servo2_angle = -90;
*/
/*******************************************************************/
/****************** SERVO CONTROL ******************/
/*
Changing the global servoX_angle at any point in the code will
move the servo to the desired angle.
*/
servo1_counter = (servo1_angle + 90)*(18)/180 + 6; // between 600 and 2400 us
if (servo1_period == 0) {
mPORTASetBits(BIT_2);
servo1_period = SERVOMAXPERIOD; /* 200 * 100us = 20000us period */
}
servo2_counter = (servo2_angle + 90)*(18)/180 + 6; // between 600 and 2400 us
if (servo2_period == 0) {
mPORTASetBits(BIT_3);
servo2_period = SERVOMAXPERIOD; /* 200 * 100us = 20000us period */
}
/*****************************************************/
} /* end of while(1) */
return 0;
}
/****************************************************************************
Function:
static void InitializeBoard(void)
Description:
This routine initializes the hardware. It is a generic initialization
routine for many of the Microchip development boards, using definitions
in HardwareProfile.h to determine specific initialization.
Precondition:
None
Parameters:
None - None
Returns:
None
Remarks:
None
***************************************************************************/
static void InitializeBoard(void) {
// WiFi Module hardware Initialization handled by Library
// Enable multi-vectored interrupts
INTEnableSystemMultiVectoredInt();
// Enable optimal performance
SYSTEMConfigPerformance(GetSystemClock());
mOSCSetPBDIV(OSC_PB_DIV_1); // Use 1:1 CPU Core:Peripheral clocks
// Disable JTAG port so we get our I/O pins back, but first
// wait 50ms so if you want to reprogram the part with
// JTAG, you'll still have a tiny window before JTAG goes away.
// The PIC32 Starter Kit debuggers use JTAG and therefore must not
// disable JTAG.
DelayMs(50);
DDPCONbits.JTAGEN = 0;
// LEDs
LEDS_OFF();
mPORTESetPinsDigitalOut(BIT_5 | BIT_6 | BIT_7);
// Switches
mPORTDSetPinsDigitalIn(BIT_4 | BIT_5 | BIT_6);
ConfigCNPullups(CN13_PULLUP_ENABLE | CN14_PULLUP_ENABLE | CN15_PULLUP_ENABLE);
// LCD
mPORTESetPinsDigitalOut(BIT_0 | BIT_1 | BIT_2 | BIT_3);
//Configure LCD SPI pins
mPORTFSetPinsDigitalOut(BIT_8);
mPORTDSetPinsDigitalOut(BIT_15);
//SPI Flash
mPORTDSetPinsDigitalOut(BIT_14);
//UART
mPORTFSetPinsDigitalOut(BIT_5);
mPORTFSetPinsDigitalIn(BIT_4);
//MiWi
#if defined(MRF24J40) || defined(MRF49XA)
PHY_CS = 1;
mPORTDSetPinsDigitalOut(BIT_9);
PHY_RESETn = 1;
mPORTDSetPinsDigitalOut(BIT_11);
#endif
#if defined(MRF49XA)
nFSEL_TRIS = 0;
FINT_TRIS = 1;
nFSEL = 1;
#elif defined(MRF24J40)
PHY_WAKE = 1;
mPORTBSetPinsDigitalOut(BIT_9);
#else
Data_nCS_TRIS = 0;
Config_nCS_TRIS = 0;
Data_nCS = 1;
Config_nCS = 1;
IRQ1_INT_TRIS = 1;
IRQ0_INT_TRIS = 1;
#endif
/* Set the Port Directions of SDO, SDI, Clock & Slave Select Signal */
/* Set SCK port pin to output */
mPORTDSetPinsDigitalOut(BIT_10);
/* Set SDO port pin to output */
mPORTDSetPinsDigitalOut(BIT_0);
/* Set SDI port pin to input */
mPORTCSetPinsDigitalIn(BIT_4);
/* Set INT1, INT2 port pins to input */
mPORTESetPinsDigitalIn(BIT_8 | BIT_9);
/* Clear SPI1CON register */
SPI1CONCLR = 0xFFFFFFFF;
#ifdef HARDWARE_SPI
unsigned int pbFreq;
/* Enable SPI1, Set to Master Mode & Set CKE bit : Serial output data changes on transition
from active clock state to Idle clock state */
SPI1CON = 0x00008120;
/* Peripheral Bus Frequency = System Clock / PB Divider */
pbFreq = (DWORD) CLOCK_FREQ / (1 << mOSCGetPBDIV());
/* PB Frequency can be maximum 40 MHz */
if (pbFreq > (2 * MAX_SPI_CLK_FREQ_FOR_P2P)) {
{
unsigned int SPI_Clk_Freq;
unsigned char SPI_Brg1 = 1;
//For the SPI1
/* Continue the loop till you find SPI Baud Rate Register Value */
while (1) {
/* SPI Clock Calculation as per PIC32 Manual */
SPI_Clk_Freq = pbFreq / (2 * (SPI_Brg1 + 1));
if (SPI_Clk_Freq <= MAX_SPI_CLK_FREQ_FOR_P2P) {
break;
}
SPI_Brg1++;
}
mSpiChnSetBrg(1, SPI_Brg1);
}
} else {
/* Set SPI1 Baud Rate */
mSpiChnSetBrg(1, 0);
}
#endif
/* Set the Interrupt Priority */
mINT2SetIntPriority(4);
#if defined(MRF89XA)
mINT1SetIntPriority(4);
#endif
/* Set Interrupt Subpriority Bits for INT2 */
mINT2SetIntSubPriority(2);
#if defined(MRF89XA)
mINT2SetIntSubPriority(1);
#endif
/* Set INT2 to falling edge */
mINT2SetEdgeMode(0);
#if defined(MRF89XA)
mINT1SetEdgeMode(1);
mINT2SetEdgeMode(1);
#endif
/* Enable INT2 */
mINT2IntEnable(1);
#if defined(MRF89XA)
mINT2IntEnable(1);
#endif
/* Enable Multi Vectored Interrupts */
// INTEnableSystemMultiVectoredInt();
#if defined(MRF89XA)
PHY_IRQ1 = 0;
PHY_IRQ0 = 0;
PHY_RESETn_TRIS = 1;
#else
RFIF = 0;
if (RF_INT_PIN == 0) {
RFIF = 1;
}
#endif
// Initialize the EEPROM
XEEInit();
// UART Initialization
#if defined(STACK_USE_UART)
UARTTX_TRIS = 0;
UARTRX_TRIS = 1;
UMODE = 0x8000; // Set UARTEN. Note: this must be done before setting UTXEN
USTA = 0x00001400; // RXEN set, TXEN set
#define CLOSEST_UBRG_VALUE ((GetPeripheralClock()+8ul*BAUD_RATE)/16/BAUD_RATE-1)
#define BAUD_ACTUAL (GetPeripheralClock()/16/(CLOSEST_UBRG_VALUE+1))
#define BAUD_ERROR ((BAUD_ACTUAL > BAUD_RATE) ? BAUD_ACTUAL-BAUD_RATE : BAUD_RATE-BAUD_ACTUAL)
#define BAUD_ERROR_PRECENT ((BAUD_ERROR*100+BAUD_RATE/2)/BAUD_RATE)
#if (BAUD_ERROR_PRECENT > 3)
#warning UART frequency error is worse than 3%
#elif (BAUD_ERROR_PRECENT > 2)
#warning UART frequency error is worse than 2%
#endif
UBRG = CLOSEST_UBRG_VALUE;
#endif
}
//********************************
//********************************
//********** INITIALISE **********
//********************************
//********************************
void initialise (void)
{
BYTE data;
//##### GENERAL NOTE ABOUT PIC32'S #####
//Try and use the peripheral libraries instead of special function registers for everything (literally everything!) to avoid
//bugs that can be caused by the pipeline and interrupts.
//---------------------------------
//----- CONFIGURE PERFORMANCE -----
//---------------------------------
//----- SETUP EVERYTHING FOR OPTIMUM PERFORMANCE -----
SYSTEMConfigPerformance(80000000ul); //Note this sets peripheral bus to '1' max speed (regardless of configuration bit setting)
//Use PBCLK divider of 1:1 to calculate UART baud, timer tick etc
//----- SET PERIPHERAL BUS DIVISOR -----
//To minimize dynamic power the PB divisor should be chosen to run the peripherals at the lowest frequency that provides acceptable system performance
mOSCSetPBDIV(OSC_PB_DIV_2); //OSC_PB_DIV_1, OSC_PB_DIV_2, OSC_PB_DIV_4, OSC_PB_DIV_8,
//----- SETUP INTERRUPTS -----
INTEnableSystemMultiVectoredInt();
//-------------------------
//----- SETUP IO PINS -----
//-------------------------
//(Device will powerup with all IO pins as inputs)
//----- TURN OFF THE JTAG PORT -----
//(JTAG is on by default)
//mJTAGPortEnable(0); //Must be on for Microchip Multimedia Development board
#define PORTA_IO 0xc2ff //Setup the IO pin type (0 = output, 1 = input)
mPORTAWrite(0xc033); //Set initial ouput pin states
mPORTASetPinsDigitalIn(PORTA_IO); //(Sets high bits as input)
mPORTASetPinsDigitalOut(~PORTA_IO); //(Sets high bits as output)
#define PORTB_IO 0xfbff //Setup the IO pin type (0 = output, 1 = input)
mPORTBWrite(0x6d13); //Set initial ouput pin states
mPORTBSetPinsDigitalIn(PORTB_IO); //(Sets high bits as input)
mPORTBSetPinsDigitalOut(~PORTB_IO); //(Sets high bits as output)
mPORTBSetPinsDigitalIn(BIT_0 | BIT_1 | BIT_3 | BIT_4 | BIT_15); //Joystick inputs
#define PORTC_IO 0xf01e //Setup the IO pin type (0 = output, 1 = input)
mPORTCWrite(0x3018); //Set initial ouput pin states
mPORTCSetPinsDigitalIn(PORTC_IO); //(Sets high bits as input)
mPORTCSetPinsDigitalOut(~PORTC_IO); //(Sets high bits as output)
#define PORTD_IO 0x7bfe //Setup the IO pin type (0 = output, 1 = input)
mPORTDWrite(0xbdaf); //Set initial ouput pin states
mPORTDSetPinsDigitalIn(PORTD_IO); //(Sets high bits as input)
mPORTDSetPinsDigitalOut(~PORTD_IO); //(Sets high bits as output)
mPORTDSetPinsDigitalOut(BIT_2 | BIT_1); //LED's 2 and 3
mPORTDSetPinsDigitalIn(BIT_9);
#define PORTE_IO 0x03ff //Setup the IO pin type (0 = output, 1 = input)
mPORTEWrite(0x02a2); //Set initial ouput pin states
mPORTESetPinsDigitalIn(PORTE_IO); //(Sets high bits as input)
mPORTESetPinsDigitalOut(~PORTE_IO); //(Sets high bits as output)
#define PORTF_IO 0x111f //Setup the IO pin type (0 = output, 1 = input)
mPORTFWrite(0x0039); //Set initial ouput pin states
mPORTFSetPinsDigitalIn(PORTF_IO); //(Sets high bits as input)
mPORTFSetPinsDigitalOut(~PORTF_IO); //(Sets high bits as output)
#define PORTG_IO 0xd3cf //Setup the IO pin type (0 = output, 1 = input)
mPORTGWrite(0xf203); //Set initial ouput pin states
mPORTGSetPinsDigitalIn(PORTG_IO); //(Sets high bits as input)
mPORTGSetPinsDigitalOut(~PORTG_IO); //(Sets high bits as output)
//Read pins using:
// mPORTAReadBits(BIT_0);
//Write pins using:
// mPORTAClearBits(BIT_0);
// mPORTASetBits(BIT_0);
// mPORTAToggleBits(BIT_0);
//----- INPUT CHANGE NOTIFICATION CONFIGURATION -----
//EnableCN0();
ConfigCNPullups(CN2_PULLUP_ENABLE | CN3_PULLUP_ENABLE | CN5_PULLUP_ENABLE | CN6_PULLUP_ENABLE | CN12_PULLUP_ENABLE); //Joystick pins
//----- SETUP THE A TO D PINS -----
ENABLE_ALL_DIG;
//---------------------
//----- SETUP USB -----
//---------------------
//The USB specifications require that USB peripheral devices must never source current onto the Vbus pin. Additionally, USB peripherals should not source
//current on D+ or D- when the host/hub is not actively powering the Vbus line. When designing a self powered (as opposed to bus powered) USB peripheral
//device, the firmware should make sure not to turn on the USB module and D+ or D- pull up resistor unless Vbus is actively powered. Therefore, the
//firmware needs some means to detect when Vbus is being powered by the host. A 5V tolerant I/O pin can be connected to Vbus (through a resistor), and
//can be used to detect when Vbus is high (host actively powering), or low (host is shut down or otherwise not supplying power). The USB firmware
//can then periodically poll this I/O pin to know when it is okay to turn on the USB module/D+/D- pull up resistor. When designing a purely bus powered
//peripheral device, it is not possible to source current on D+ or D- when the host is not actively providing power on Vbus. Therefore, implementing this
//bus sense feature is optional. This firmware can be made to use this bus sense feature by making sure "USE_USB_BUS_SENSE_IO" has been defined in the
//HardwareProfile.h file.
// #if defined(USE_USB_BUS_SENSE_IO)
// tris_usb_bus_sense = INPUT_PIN; // See HardwareProfile.h
// #endif
//If the host PC sends a GetStatus (device) request, the firmware must respond and let the host know if the USB peripheral device is currently bus powered
//or self powered. See chapter 9 in the official USB specifications for details regarding this request. If the peripheral device is capable of being both
//self and bus powered, it should not return a hard coded value for this request. Instead, firmware should check if it is currently self or bus powered, and
//respond accordingly. If the hardware has been configured like demonstrated on the PICDEM FS USB Demo Board, an I/O pin can be polled to determine the
//currently selected power source. On the PICDEM FS USB Demo Board, "RA2" is used for this purpose. If using this feature, make sure "USE_SELF_POWER_SENSE_IO"
//has been defined in HardwareProfile.h, and that an appropriate I/O pin has been mapped to it in HardwareProfile.h.
// #if defined(USE_SELF_POWER_SENSE_IO)
// tris_self_power = INPUT_PIN; // See HardwareProfile.h
// #endif
//Enable the USB port now - we will check to see if Vbus is powered at the end of init and disable it if not.
//USBDeviceInit(); //usb_device.c. Initializes USB module SFRs and firmware variables to known states.
//------------------------
//----- SETUP TIMERS -----
//------------------------
//(INCLUDE THE USAGE OF ALL TIMERS HERE EVEN IF NOT SETUP HERE SO THIS IS THE ONE POINT OF
//REFERENCE TO KNOW WHICH TIMERS ARE IN USE AND FOR WHAT).
//----- SETUP TIMER 1 -----
//Used for: Available
//OpenTimer1((T1_ON | T1_IDLE_CON | T1_GATE_OFF | T1_PS_1_4 | T1_SOURCE_INT), 20000);
//----- SETUP TIMER 2 -----
//Used for:
//OpenTimer2((T2_ON | T2_IDLE_CON | T2_GATE_OFF | T2_PS_1_1 | T2_SOURCE_INT), 0xffff); //0xffff = 305Hz
//----- SETUP TIMER 3 -----
//Used for:
//OpenTimer3((T3_ON | T3_IDLE_CON | T3_GATE_OFF | T3_PS_1_1 | T3_SOURCE_INT), PIEZO_TIMER_PERIOD);
//----- SETUP TIMER 4 -----
//Used for:
//OpenTimer4((T4_ON | T4_IDLE_CON | T4_GATE_OFF | T4_PS_1_1 | T4_SOURCE_INT), 20000);
//----- SETUP TIMER 5 -----
//Used for: Heartbeat
OpenTimer5((T5_ON | T5_IDLE_CON | T5_GATE_OFF | T5_PS_1_1 | T5_SOURCE_INT), 40000); //1mS with 80MHz osc and PB_DIV_2
ConfigIntTimer5(T5_INT_ON | T5_INT_PRIOR_7); //1=lowest priority to 7=highest priority. ISR function must specify same value
//---------------------------------
//----- SETUP EVAL BOARD CPLD -----
//---------------------------------
//Graphics bus width = 16
mPORTGSetPinsDigitalOut(BIT_14);
mPORTGSetBits(BIT_14);
//SPI source select = SPI3 (not used)
mPORTGSetPinsDigitalOut(BIT_12);
mPORTGClearBits(BIT_12);
//SPI peripheral destination select = Expansion Slot (not used)
mPORTASetPinsDigitalOut(BIT_7 | BIT_6);
mPORTASetBits(BIT_7);
mPORTAClearBits(BIT_6);
//--------------------------------------
//----- PARALLEL MASTER PORT SETUP -----
//--------------------------------------
PMMODE = 0;
PMAEN = 0;
PMCON = 0;
PMMODE = 0x0610;
PMCONbits.PTRDEN = 1; //Enable RD line
PMCONbits.PTWREN = 1; //Enable WR line
PMCONbits.PMPEN = 1; //Enable PMP
//------------------------------
//----- INITIALISE DISPLAY -----
//------------------------------
display_initialise();
display_test();
//LOAD OUR GLOBAL HTML STYLES FILE READY FOR DISPLAY HTML PAGES
BYTE dummy_styles_count;
DWORD file_size;
if (display_html_setup_read_file(global_css, 0, &file_size))
{
dummy_styles_count = 0;
display_html_read_styles(&file_size, &dummy_styles_count, 1); //1 = this is global styles file
}
}
int main(void)
{
DBINIT();
DBPRINTF("MAIN.... \n");
unsigned int temp;
int POWER;
//bool RELAY;
//~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
//STEP 1. Configure cache, wait states and peripheral bus clock
SYSTEMConfig(SYS_FREQ, SYS_CFG_WAIT_STATES | SYS_CFG_PCACHE);
//~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
// STEP 2. configure the port registers
mPORTDSetPinsDigitalOut(BIT_0 | BIT_1 | BIT_2 | BIT_9);
mPORTESetPinsDigitalOut(BIT_0 | BIT_1 | BIT_2);
//~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
// STEP 3. initialize the port pin states = outputs low
mPORTDClearBits(BIT_0 | BIT_1 | BIT_2);
//~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
// STEP 4. enable change notice, enable discrete pins and weak pullups
mCNOpen(CONFIG, PINS, PULLUPS);
//~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
// STEP 5. read port(s) to clear mismatch on change notice pins
temp = mPORTDRead();
//~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
// STEP 6. clear change notice interrupt flag
ConfigIntCN(INTERRUPT);
//~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
// STEP 7. enable multi-vector interrupts
INTEnableSystemMultiVectoredInt();
//~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
// STEP 8. configure SPI port and MCP3909
OpenSPI1(FRAME_ENABLE_ON | ENABLE_SDO_PIN | SPI_MODE32_ON | SPI_CKE_ON | SLAVE_ENABLE_OFF | CLK_POL_ACTIVE_LOW | MASTER_ENABLE_ON , SPI_ENABLE | SPI_FRZ_CONTINUE | SPI_IDLE_STOP | SPI_RX_OVFLOW_CLR);
CONFIG_3909();
DBPRINTF("CONFIGURED.... \n");
while(1)
{
// Toggle LED's to signify code is looping
mPORTDToggleBits(BIT_0); // toggle LED1 (same as LATDINV = 0x0002)
SAMPLE();
POWER = MEASURE_POWER();
DBPRINTF("power measured! \n");
DelayMs(1000);
/************************
*ETHERNET COMMUNICATIONS*
************************/
};
}
int main(int argc, char** argv) {
uchar status = 0;
mPORTAClearBits(BIT_6); //Clear bits to ensure the LED is off.
//mPORTASetPinsDigitalOut(BIT_6); //Set port as output
// lets set the digital IO bits for the ethernet module
mPORTASetPinsDigitalOut(BIT_7|BIT_6);
mPORTGSetPinsDigitalOut(BIT_8 | BIT_9 | BIT_14 | BIT_0);
mPORTBSetPinsDigitalOut(0x0000FFFF);
mPORTESetPinsDigitalOut(0x000000FF);
// set the control bits high
mPORTASetBits(BIT_7);
mPORTGSetBits(BIT_8 | BIT_9 | BIT_14);
mPORTGClearBits(BIT_0);
//mPORTGClearBits(BIT_0);
//mPORTGClearBits(0x0000FFFF);
//mPORTEClearBits(0x0000FFFF);
//mPORTAClearBits(0x0000FFFF);
//mPORTBClearBits(0x0000FFFF);
//while(1){}
// lets init the W5100
struct W5100Context_t context;
context.Mode = MR_RST;
context.InterruptMask = 0xFF;
context.RetryTimeValue = 0x0FA0; // 400 ms
context.RetryCount = 1;
context.GateAdd[0] = 10;
context.GateAdd[1] = 1;
context.GateAdd[2] = 1;
context.GateAdd[3] = 3;
context.SHardAdd[0] = 0;
context.SHardAdd[1] = 1;
context.SHardAdd[2] = 2;
context.SHardAdd[3] = 3;
context.SHardAdd[4] = 4;
context.SHardAdd[5] = 5;
context.Subnet[0] = 255;
context.Subnet[1] = 255;
context.Subnet[2] = 255;
context.Subnet[3] = 0;
context.SourceIP[0] = 10;
context.SourceIP[1] = 1;
context.SourceIP[2] = 1;
context.SourceIP[3] = 2;
context.sockets[0].Mem = MEM_2K;
context.sockets[1].Mem = MEM_2K;
context.sockets[2].Mem = MEM_2K;
context.sockets[3].Mem = MEM_2K;
ShortDelay_ms(100);
W5100Init( &context );
W5100ReadData(SHAR0, &status, 1);
W5100ReadData(SHAR1, &status, 1);
W5100ReadData(SHAR2, &status, 1);
W5100ReadData(SHAR3, &status, 1);
W5100ReadData(SHAR4, &status, 1);
W5100ReadData(SHAR5, &status, 1);
EstablishServer(&context);
// lets try a random write
//W5100WriteData(0x001A, 0x07, 1);
//mPORTEWrite(0x07);
while(1)
{
status = W5100PollStatus(&context, 0);
if( status == SOCK_ESTABLISH)
mPORTGSetBits(BIT_0);
else
mPORTGClearBits(BIT_0);
if( status == SOCK_CLOSE_WAIT)
EstablishServer(&context);
//PORTAbits.RA2 = ~PORTAbits.RA2;
mPORTAToggleBits(BIT_6);
ShortDelay(US_TO_CT_TICKS*1000000);
//delay_millis(1000);
}
return (EXIT_SUCCESS);
}
/*******************************************************************************
* Function: BoardInit(void)
* PreCondition:None
* Input: None
* Output: None
* Overview: SPI pins and SFR, Maintenance Tasks Timer, External Interrupts,
* and other board issues initialization.
* Note: This routine needs to be called before initialising MiWi stack
* or invoking other function that operates on MiWi stack.
******************************************************************************/
void BoardInit(void){
#if defined(__PIC32MX__)
// RADIO INTERFACES & SPI INIT -------------------------------------------//
#if defined HARDWARE_SPI
/* Peripheral Bus Frequency = System Clock / PB Divider */
unsigned int pbFreq;
pbFreq = (DWORD) CLOCK_FREQ/(1 << mOSCGetPBDIV());
unsigned int SPI_Clk_Freq;
unsigned char SPI_Brg;
#endif
#if defined MRF24J40
PHY_CS_TRIS = 0;
PHY_CS = 1;
PHY_RESETn_TRIS = 0;
PHY_RESETn = 1;
MRF24J40_INT_TRIS = 1;
SDI_TRIS = 1;
SDO_TRIS = 0;
SCK_TRIS = 0;
SPI_SDO = 0;
SPI_SCK = 0;
PHY_WAKE_TRIS = 0;
PHY_WAKE = 1;
SPICONCLR = 0xFFFFFFFF; // Clear SPIxCON register
#ifdef HARDWARE_SPI
/* Enable SPI, Set to Master Mode & Set CKE bit : Serial output
* data changes on transition from active clock state to Idle
* clock state */
SPICON = 0x00008120;
/* PB Frequency can be maximum 40 MHz */
if(pbFreq > (2 * MAX_SPI_CLK_FREQ_FOR_P2P)){
SPI_Brg = 1;
/* Continue the loop till you find SPI Baud Rate Reg Value */
while(1){
/* SPI Clock Calculation as per PIC32 Manual */
SPI_Clk_Freq = pbFreq / (2 * (SPI_Brg + 1));
if(SPI_Clk_Freq <= MAX_SPI_CLK_FREQ_FOR_P2P){
break;
}
SPI_Brg++;
}
#if defined MRF24J40_IN_SPI1
mSpiChnSetBrg (1, SPI_Brg);
#elif defined MRF24J40_IN_SPI2
mSpiChnSetBrg (2, SPI_Brg);
#elif defined MRF24J40_IN_SPI3
mSpiChnSetBrg (1A, SPI_Brg);
#elif defined MRF24J40_IN_SPI4
mSpiChnSetBrg (3A, SPI_Brg);
#endif
}
else{
#if defined MRF24J40_IN_SPI1
mSpiChnSetBrg (1, 0);
#elif defined MRF24J40_IN_SPI2
mSpiChnSetBrg (2, 0);
#elif defined MRF24J40_IN_SPI3
mSpiChnSetBrg (1A, 0);
#elif defined MRF24J40_IN_SPI4
mSpiChnSetBrg (3A, SPI_Brg);
#endif
}
#endif
#endif
#if defined(MRF49XA_1)
//Configuration for Guilja's Expansion Board, Connection SLot 1 --//
mPORTESetPinsDigitalOut(BIT_1); //nCS
mPORTBSetPinsDigitalIn(BIT_2); //FINT //Juan: Added.
//----------------------------------------------------------------//
MRF49XA_1_PHY_CS_TRIS = 0;
MRF49XA_1_PHY_CS = 1;
MRF49XA_1_PHY_RESETn_TRIS = 0;
MRF49XA_1_PHY_RESETn = 1;
MRF49XA_1_INT_TRIS = 1;
MRF49XA_1_SDI_TRIS = 1;
MRF49XA_1_SDO_TRIS = 0;
MRF49XA_1_SCK_TRIS = 0;
MRF49XA_1_SPI_SDO = 0;
MRF49XA_1_SPI_SCK = 0;
MRF49XA_1_nFSEL_TRIS = 0;
MRF49XA_1_FINT_TRIS = 1;
MRF49XA_1_nFSEL = 1; // nFSEL inactive
MRF49XA_1_SPICONCLR = 0xFFFFFFFF; //Clear SPIxCON register
#ifdef HARDWARE_SPI
/* Enable SPI1, Set to Master Mode & Set CKE bit : Serial output
* data changes on transition from active clock state to Idle
* clock state */
MRF49XA_1_SPICON = 0x00008120;
/* PB Frequency can be maximum 40 MHz */
if(pbFreq > (2 * MAX_SPI_CLK_FREQ_FOR_P2P)){
SPI_Brg = 1;
/* Continue the loop till you find SPI Baud Rate Reg Value */
while(1){
/* SPI Clock Calculation as per PIC32 Manual */
SPI_Clk_Freq = pbFreq / (2 * (SPI_Brg + 1));
if(SPI_Clk_Freq <= MAX_SPI_CLK_FREQ_FOR_P2P){
break;
}
SPI_Brg++;
}
#if defined MRF49XA_1_IN_SPI1
mSpiChnSetBrg (1, SPI_Brg);
#elif defined MRF49XA_1_IN_SPI2
mSpiChnSetBrg (2, SPI_Brg);
#elif defined MRF49XA_1_IN_SPI3
mSpiChnSetBrg (1A, SPI_Brg);
#endif
}
else{
#if defined MRF49XA_1_IN_SPI1
mSpiChnSetBrg (1, 0);
#elif defined MRF49XA_1_IN_SPI2
mSpiChnSetBrg (2, 0);
#elif defined MRF49XA_1_IN_SPI3
mSpiChnSetBrg (1A, 0);
#endif
}
#endif
#endif
#if defined(MRF49XA_2)
MRF49XA_2_PHY_CS_TRIS = 0;
MRF49XA_2_PHY_CS = 1;
MRF49XA_2_PHY_RESETn_TRIS = 0;
MRF49XA_2_PHY_RESETn = 1;
MRF49XA_2_INT_TRIS = 1;
MRF49XA_2_SDI_TRIS = 1;
MRF49XA_2_SDO_TRIS = 0;
MRF49XA_2_SCK_TRIS = 0;
MRF49XA_2_SPI_SDO = 0;
MRF49XA_2_SPI_SCK = 0;
MRF49XA_2_nFSEL_TRIS = 0;
MRF49XA_2_FINT_TRIS = 1;
MRF49XA_2_nFSEL = 1; // nFSEL inactive
MRF49XA_2_SPICONCLR = 0xFFFFFFFF; // Clear SPIxCON register
#ifdef HARDWARE_SPI
/* Enable SPI1, Set to Master Mode & Set CKE bit : Serial output
* data changes on transition from active clock state to Idle
* clock state */
MRF49XA_2_SPICON = 0x00008120;
/* PB Frequency can be maximum 40 MHz */
if(pbFreq > (2 * MAX_SPI_CLK_FREQ_FOR_P2P)){
SPI_Brg = 1;
/* Continue the loop till you find SPI Baud Rate Reg Value */
while(1){
/* SPI Clock Calculation as per PIC32 Manual */
SPI_Clk_Freq = pbFreq / (2 * (SPI_Brg + 1));
if(SPI_Clk_Freq <= MAX_SPI_CLK_FREQ_FOR_P2P){
break;
}
SPI_Brg++;
}
#if defined MRF49XA_2_IN_SPI1
mSpiChnSetBrg (1, SPI_Brg);
#elif defined MRF49XA_2_IN_SPI2
mSpiChnSetBrg (2, SPI_Brg);
#elif defined MRF49XA_2_IN_SPI3
mSpiChnSetBrg (1A, SPI_Brg);
#endif
}
else{
#if defined MRF49XA_2_IN_SPI1
mSpiChnSetBrg (1, 0);
#elif defined MRF49XA_2_IN_SPI2
mSpiChnSetBrg (2, 0);
#elif defined MRF49XA_2_IN_SPI3
mSpiChnSetBrg (1A, 0);
#endif
}
#endif
#endif
// SPI & EXTERNAL INTERRUPTS PINS AND CONFIGURATION ----------------------//
#if (defined __32MX675F256L__ || defined ____32MX675F512__)
/* Set the SPI Port Directions (SDO, SDI, SCK) for every SPI module.*/
#if defined MRF49XA_1_IN_SPI1 || defined MRF49XA_2_IN_SPI1 || \
defined MRF89XA_IN_SPI1 || defined MRF24J40_IN_SPI1 || \
defined MRF24WB0M_IN_SPI1
mPORTDSetPinsDigitalOut(BIT_0); //SDO1
mPORTDSetPinsDigitalOut(BIT_10); //SCK1
mPORTCSetPinsDigitalIn(BIT_4); //SDI1
#endif
#if defined MRF49XA_1_IN_SPI2 || defined MRF49XA_2_IN_SPI2 || \
defined MRF89XA_IN_SPI2 || defined MRF24J40_IN_SPI2 || \
defined MRF24WB0M
mPORTGSetPinsDigitalOut(BIT_8); //SDO2
mPORTGSetPinsDigitalOut(BIT_6); //SCK2
mPORTGSetPinsDigitalIn(BIT_7); //SDI2
#endif
#if defined MRF49XA_1_IN_SPI3 || defined MRF49XA_2_IN_SPI3 || \
defined MRF89XA_IN_SPI3 || defined MRF24J40_IN_SPI3 || \
defined MRF24WB0M
mPORTFSetPinsDigitalOut(BIT_8); //SDO3
mPORTDSetPinsDigitalOut(BIT_15); //SCK3
mPORTFSetPinsDigitalIn(BIT_2); //SDI3
#endif
// #if defined MRF24WB0M_IN_SPI4
// mPORTFSetPinsDigitalOut(BIT_5); //SDO4
// mPORTFSetPinsDigitalOut(BIT_13); //SCK4
// mPORTFSetPinsDigitalIn(BIT_4); //SDI4
// #endif
#endif
#endif
// TIMER 1 FOR TIME_SYNC -------------------------------------------------//
#if defined(ENABLE_TIME_SYNC)
//TIMER 1 MAY BE USED FOR SLEEP MODE AND/OR FOR STACKS MAINTENANCE. IT
//NEEDS ADAPTATION BEFORE ENABLING TIME_SYNC WITH TIMER 1 TOO!
T1CON = 0;
T1CON = 0x0012;
T1CONSET = 0x8000;
PR1 = 0xFFFF;
IFS0bits.T1IF = 0;
mT1IntEnable(1);
mT1SetIntPriority(4);
while(T1CONbits.TWIP);
TMR1 = 0;
#endif
// TIMER 1 FOR NODE STACKS AUTO-MAINTENANCE ------------------------------//
#if defined NODE_DOES_MAINTENANCE_TASKS
T1CON = 0x0070; //Disable timer, PBCLK source, PS=256
TMR1 = 0x0000; //Reset count
PR1 = MAINTENANCE_PERIOD; //Set period.
IPC1SET = 0x00000005; //Set Priority level 1, Subpriority level 1
IFS0CLR = 0x00000010; //Clear T1IF
IEC0SET = 0x00000010; //Set T1IE
//Timer will be triggered after initialization.
#endif
// IOPORT CN - For waking up the node manually. --------------------------//
mPORTDSetPinsDigitalIn(BIT_5); // CN14
CNCON = 0x8000; //Module enabled.
CNEN = 0x00004000; //Enable CN14
CNPUE = 0x00004000; //Enable CN14 weak pull-up.
ReadBUTTONS(); //Clear PORT mismatch condition.
IFS1CLR = 0x00000001; //Clear the CN interrupt flag status bit
IPC6SET = 0x00180000; //Set CN priority 6, subpriority 0.
//It will be enabled only during sleep mode time interval
//------------------------------------------------------------------------//
// Lo modifico en el wifi config
#if defined(ENABLE_NVM) //REVIEW
//EE_nCS_TRIS = 0;//FERNANDO, CUIDADO NO SE SI LA PILA REALMENTE FUNCIONA CON FLASH MEMORY
//EE_nCS = 1;
#endif
// INTERRUPTION FLAGS AND EXT_INT PIN FINAL SETTINGS ---------------------//
#if defined MRF49XA_1
MRF49XA_1_IF = 0;
if(MRF49XA_1_INT_PIN == 0){
MRF49XA_1_IF = 1;
}
#endif
#if defined MRF49XA_2
MRF49XA_2_IF = 0;
if(MRF49XA_2_INT_PIN == 0){
MRF49XA_2_IF = 1;
}
#endif
#if defined MRF89XA
PHY_IRQ1 = 0;
#endif
#if defined MRF24J40
MRF24J40_IF = 0;
if(MRF24J40_INT_PIN == 0){
MRF24J40_IF = 1;
}
#endif
}
