int __init cbus_bus_init(void)
{
struct cbus_host *chost;
int ret;
chost = kmalloc(sizeof (*chost), GFP_KERNEL);
if (chost == NULL)
return -ENOMEM;
memset(chost, 0, sizeof (*chost));
spin_lock_init(&chost->lock);
/* REVISIT: Pass these from board-*.c files in platform_data */
if (machine_is_nokia770()) {
chost->clk_gpio = OMAP_MPUIO(11);
chost->dat_gpio = OMAP_MPUIO(10);
chost->sel_gpio = OMAP_MPUIO(9);
} else if (machine_is_nokia_n800() || machine_is_nokia_n810() ||
machine_is_nokia_n810_wimax()) {
chost->clk_gpio = 66;
chost->dat_gpio = 65;
chost->sel_gpio = 64;
} else {
printk(KERN_ERR "cbus: Unsupported board\n");
ret = -ENODEV;
goto exit1;
}
#ifdef CONFIG_ARCH_OMAP1
if (!OMAP_GPIO_IS_MPUIO(chost->clk_gpio) ||
!OMAP_GPIO_IS_MPUIO(chost->dat_gpio) ||
!OMAP_GPIO_IS_MPUIO(chost->sel_gpio)) {
printk(KERN_ERR "cbus: Only MPUIO pins supported\n");
ret = -ENODEV;
goto exit1;
}
#endif
if ((ret = gpio_request(chost->clk_gpio, "CBUS clk")) < 0)
goto exit1;
if ((ret = gpio_request(chost->dat_gpio, "CBUS data")) < 0)
goto exit2;
if ((ret = gpio_request(chost->sel_gpio, "CBUS sel")) < 0)
goto exit3;
gpio_direction_output(chost->clk_gpio, 0);
gpio_direction_input(chost->dat_gpio);
gpio_direction_output(chost->sel_gpio, 1);
gpio_set_value(chost->clk_gpio, 1);
gpio_set_value(chost->clk_gpio, 0);
cbus_host = chost;
return 0;
exit3:
gpio_free(chost->dat_gpio);
exit2:
gpio_free(chost->clk_gpio);
exit1:
kfree(chost);
return ret;
}
static int ohci_omap_reset(struct usb_hcd *hcd)
{
struct ohci_hcd *ohci = hcd_to_ohci(hcd);
struct omap_usb_config *config = dev_get_platdata(hcd->self.controller);
int need_transceiver = (config->otg != 0);
int ret;
dev_dbg(hcd->self.controller, "starting USB Controller\n");
if (config->otg) {
hcd->self.otg_port = config->otg;
/* default/minimum OTG power budget: 8 mA */
hcd->power_budget = 8;
}
/* boards can use OTG transceivers in non-OTG modes */
need_transceiver = need_transceiver
|| machine_is_omap_h2() || machine_is_omap_h3();
/* XXX OMAP16xx only */
if (config->ocpi_enable)
config->ocpi_enable();
#ifdef CONFIG_USB_OTG
if (need_transceiver) {
hcd->phy = usb_get_phy(USB_PHY_TYPE_USB2);
if (!IS_ERR_OR_NULL(hcd->phy)) {
int status = otg_set_host(hcd->phy->otg,
&ohci_to_hcd(ohci)->self);
dev_dbg(hcd->self.controller, "init %s phy, status %d\n",
hcd->phy->label, status);
if (status) {
usb_put_phy(hcd->phy);
return status;
}
} else {
dev_err(hcd->self.controller, "can't find phy\n");
return -ENODEV;
}
ohci->start_hnp = start_hnp;
}
#endif
omap_ohci_clock_power(1);
if (cpu_is_omap15xx()) {
omap_1510_local_bus_power(1);
omap_1510_local_bus_init();
}
ret = ohci_setup(hcd);
if (ret < 0)
return ret;
if (config->otg || config->rwc) {
ohci->hc_control = OHCI_CTRL_RWC;
writel(OHCI_CTRL_RWC, &ohci->regs->control);
}
/* board-specific power switching and overcurrent support */
if (machine_is_omap_osk() || machine_is_omap_innovator()) {
u32 rh = roothub_a (ohci);
/* power switching (ganged by default) */
rh &= ~RH_A_NPS;
/* TPS2045 switch for internal transceiver (port 1) */
if (machine_is_omap_osk()) {
ohci_to_hcd(ohci)->power_budget = 250;
rh &= ~RH_A_NOCP;
/* gpio9 for overcurrent detction */
omap_cfg_reg(W8_1610_GPIO9);
gpio_request(9, "OHCI overcurrent");
gpio_direction_input(9);
/* for paranoia's sake: disable USB.PUEN */
omap_cfg_reg(W4_USB_HIGHZ);
}
ohci_writel(ohci, rh, &ohci->regs->roothub.a);
ohci->flags &= ~OHCI_QUIRK_HUB_POWER;
} else if (machine_is_nokia770()) {
/* We require a self-powered hub, which should have
* plenty of power. */
ohci_to_hcd(ohci)->power_budget = 0;
}
/* FIXME khubd hub requests should manage power switching */
omap_ohci_transceiver_power(1);
/* board init will have already handled HMC and mux setup.
* any external transceiver should already be initialized
* too, so all configured ports use the right signaling now.
*/
return 0;
}
static int ohci_omap_init(struct usb_hcd *hcd)
{
struct ohci_hcd *ohci = hcd_to_ohci(hcd);
struct omap_usb_config *config = hcd->self.controller->platform_data;
int need_transceiver = (config->otg != 0);
int ret;
dev_dbg(hcd->self.controller, "starting USB Controller\n");
if (config->otg) {
ohci_to_hcd(ohci)->self.otg_port = config->otg;
/* default/minimum OTG power budget: 8 mA */
ohci_to_hcd(ohci)->power_budget = 8;
}
/* boards can use OTG transceivers in non-OTG modes */
need_transceiver = need_transceiver
|| machine_is_omap_h2() || machine_is_omap_h3();
if (cpu_is_omap16xx())
ocpi_enable();
#ifdef CONFIG_ARCH_OMAP_OTG
if (need_transceiver) {
ohci->transceiver = otg_get_transceiver();
if (ohci->transceiver) {
int status = otg_set_host(ohci->transceiver,
&ohci_to_hcd(ohci)->self);
dev_dbg(hcd->self.controller, "init %s transceiver, status %d\n",
ohci->transceiver->label, status);
if (status) {
if (ohci->transceiver)
put_device(ohci->transceiver->dev);
return status;
}
} else {
dev_err(hcd->self.controller, "can't find transceiver\n");
return -ENODEV;
}
}
#endif
omap_ohci_clock_power(1);
if (cpu_is_omap1510()) {
omap_1510_local_bus_power(1);
omap_1510_local_bus_init();
}
if ((ret = ohci_init(ohci)) < 0)
return ret;
/* board-specific power switching and overcurrent support */
if (machine_is_omap_osk() || machine_is_omap_innovator()) {
u32 rh = roothub_a (ohci);
/* power switching (ganged by default) */
rh &= ~RH_A_NPS;
/* TPS2045 switch for internal transceiver (port 1) */
if (machine_is_omap_osk()) {
ohci_to_hcd(ohci)->power_budget = 250;
rh &= ~RH_A_NOCP;
/* gpio9 for overcurrent detction */
omap_cfg_reg(W8_1610_GPIO9);
omap_request_gpio(9);
omap_set_gpio_direction(9, 1 /* IN */);
/* for paranoia's sake: disable USB.PUEN */
omap_cfg_reg(W4_USB_HIGHZ);
}
ohci_writel(ohci, rh, &ohci->regs->roothub.a);
distrust_firmware = 0;
} else if (machine_is_nokia770()) {
/* We require a self-powered hub, which should have
* plenty of power. */
ohci_to_hcd(ohci)->power_budget = 0;
}
/* FIXME khubd hub requests should manage power switching */
omap_ohci_transceiver_power(1);
/* board init will have already handled HMC and mux setup.
* any external transceiver should already be initialized
* too, so all configured ports use the right signaling now.
*/
return 0;
}
static int ohci_omap_init(struct usb_hcd *hcd)
{
struct ohci_hcd *ohci = hcd_to_ohci(hcd);
struct omap_usb_config *config = hcd->self.controller->platform_data;
int need_transceiver = (config->otg != 0);
int ret;
dev_dbg(hcd->self.controller, "starting USB Controller\n");
if (config->otg) {
ohci_to_hcd(ohci)->self.otg_port = config->otg;
/* */
ohci_to_hcd(ohci)->power_budget = 8;
}
/* */
need_transceiver = need_transceiver
|| machine_is_omap_h2() || machine_is_omap_h3();
if (cpu_is_omap16xx())
ocpi_enable();
#ifdef CONFIG_USB_OTG
if (need_transceiver) {
ohci->transceiver = usb_get_transceiver();
if (ohci->transceiver) {
int status = otg_set_host(ohci->transceiver->otg,
&ohci_to_hcd(ohci)->self);
dev_dbg(hcd->self.controller, "init %s transceiver, status %d\n",
ohci->transceiver->label, status);
if (status) {
if (ohci->transceiver)
put_device(ohci->transceiver->dev);
return status;
}
} else {
dev_err(hcd->self.controller, "can't find transceiver\n");
return -ENODEV;
}
ohci->start_hnp = start_hnp;
}
#endif
omap_ohci_clock_power(1);
if (cpu_is_omap15xx()) {
omap_1510_local_bus_power(1);
omap_1510_local_bus_init();
}
if ((ret = ohci_init(ohci)) < 0)
return ret;
/* */
if (machine_is_omap_osk() || machine_is_omap_innovator()) {
u32 rh = roothub_a (ohci);
/* */
rh &= ~RH_A_NPS;
/* */
if (machine_is_omap_osk()) {
ohci_to_hcd(ohci)->power_budget = 250;
rh &= ~RH_A_NOCP;
/* */
omap_cfg_reg(W8_1610_GPIO9);
gpio_request(9, "OHCI overcurrent");
gpio_direction_input(9);
/* */
omap_cfg_reg(W4_USB_HIGHZ);
}
ohci_writel(ohci, rh, &ohci->regs->roothub.a);
ohci->flags &= ~OHCI_QUIRK_HUB_POWER;
} else if (machine_is_nokia770()) {
/*
*/
ohci_to_hcd(ohci)->power_budget = 0;
}
/* */
omap_ohci_transceiver_power(1);
/*
*/
return 0;
}