/**
* @brief Low level HAL driver initialization.
*
* @notapi
*/
void hal_lld_init(void) {
/* Reset of all peripherals. AHB3 is not reseted because it could have
been initialized in the board initialization file (board.c).*/
rccResetAHB1(~0);
rccResetAHB2(~0);
rccResetAPB1(~RCC_APB1RSTR_PWRRST);
rccResetAPB2(~0);
/* SysTick initialization using the system clock.*/
SysTick->LOAD = STM32_HCLK / CH_FREQUENCY - 1;
SysTick->VAL = 0;
SysTick->CTRL = SysTick_CTRL_CLKSOURCE_Msk |
SysTick_CTRL_ENABLE_Msk |
SysTick_CTRL_TICKINT_Msk;
/* DWT cycle counter enable.*/
SCS_DEMCR |= SCS_DEMCR_TRCENA;
DWT_CTRL |= DWT_CTRL_CYCCNTENA;
/* PWR clock enabled.*/
rccEnablePWRInterface(FALSE);
/* Initializes the backup domain.*/
hal_lld_backup_domain_init();
#if defined(STM32_DMA_REQUIRED)
dmaInit();
#endif
/* Programmable voltage detector enable.*/
#if STM32_PVD_ENABLE
PWR->CR |= PWR_CR_PVDE | (STM32_PLS & STM32_PLS_MASK);
#endif /* STM32_PVD_ENABLE */
}
/**
* @brief Low level HAL driver initialization.
*
* @notapi
*/
void hal_lld_init(void) {
/* Reset of all peripherals. AHB3 is not reseted because it could have
been initialized in the board initialization file (board.c).
Note, GPIOs are not reset because initialized before this point in
board files.*/
rccResetAHB1(~STM32_GPIO_EN_MASK);
#if !defined(STM32F410xx)
rccResetAHB2(~0);
#endif
rccResetAPB1(~RCC_APB1RSTR_PWRRST);
rccResetAPB2(~0);
/* PWR clock enabled.*/
rccEnablePWRInterface(true);
/* Initializes the backup domain.*/
hal_lld_backup_domain_init();
/* DMA subsystems initialization.*/
#if defined(STM32_DMA_REQUIRED)
dmaInit();
#endif
/* IRQ subsystem initialization.*/
irqInit();
/* Programmable voltage detector enable.*/
#if STM32_PVD_ENABLE
PWR->CR |= PWR_CR_PVDE | (STM32_PLS & STM32_PLS_MASK);
#endif /* STM32_PVD_ENABLE */
}
/**
* @brief Low level HAL driver initialization.
*
* @notapi
*/
void hal_lld_init(void) {
/* Reset of all peripherals. AHB3 is not reseted because it could have
been initialized in the board initialization file (board.c).*/
rccResetAHB1(~0);
rccResetAHB2(~0);
rccResetAHB3(~0);
rccResetAPB1R1(~RCC_APB1RSTR1_PWRRST);
rccResetAPB1R2(~0);
rccResetAPB2(~0);
/* PWR clock enabled.*/
rccEnablePWRInterface(FALSE);
/* Initializes the backup domain.*/
hal_lld_backup_domain_init();
#if defined(STM32_DMA_REQUIRED)
dmaInit();
#endif
/* Programmable voltage detector enable.*/
#if STM32_PVD_ENABLE
PWR->CR1 |= PWR_CR1_PVDE | (STM32_PLS & STM32_PLS_MASK);
#endif /* STM32_PVD_ENABLE */
}
static void stm32_gpio_init(void) {
/* Enabling GPIO-related clocks, the mask comes from the
registry header file.*/
#if defined(STM32H7)
rccResetAHB4(STM32_GPIO_EN_MASK);
rccEnableAHB4(STM32_GPIO_EN_MASK, true);
#else
rccResetAHB1(STM32_GPIO_EN_MASK);
rccEnableAHB1(STM32_GPIO_EN_MASK, true);
#endif
/* Initializing all the defined GPIO ports.*/
#if STM32_HAS_GPIOA
gpio_init(GPIOA, &gpio_default_config.PAData);
#endif
#if STM32_HAS_GPIOB
gpio_init(GPIOB, &gpio_default_config.PBData);
#endif
#if STM32_HAS_GPIOC
gpio_init(GPIOC, &gpio_default_config.PCData);
#endif
#if STM32_HAS_GPIOD
gpio_init(GPIOD, &gpio_default_config.PDData);
#endif
#if STM32_HAS_GPIOE
gpio_init(GPIOE, &gpio_default_config.PEData);
#endif
#if STM32_HAS_GPIOF
gpio_init(GPIOF, &gpio_default_config.PFData);
#endif
#if STM32_HAS_GPIOG
gpio_init(GPIOG, &gpio_default_config.PGData);
#endif
#if STM32_HAS_GPIOH
gpio_init(GPIOH, &gpio_default_config.PHData);
#endif
#if STM32_HAS_GPIOI
gpio_init(GPIOI, &gpio_default_config.PIData);
#endif
#if STM32_HAS_GPIOJ
gpio_init(GPIOJ, &gpio_default_config.PJData);
#endif
#if STM32_HAS_GPIOK
gpio_init(GPIOK, &gpio_default_config.PKData);
#endif
}
