static void rt2800pci_kick_tx_queue(struct rt2x00_dev *rt2x00dev,
const enum data_queue_qid queue_idx)
{
struct data_queue *queue;
unsigned int idx, qidx = 0;
u32 reg;
if (queue_idx == QID_BEACON) {
rt2800_register_read(rt2x00dev, BCN_TIME_CFG, ®);
if (!rt2x00_get_field32(reg, BCN_TIME_CFG_BEACON_GEN)) {
rt2x00_set_field32(®, BCN_TIME_CFG_TSF_TICKING, 1);
rt2x00_set_field32(®, BCN_TIME_CFG_TBTT_ENABLE, 1);
rt2x00_set_field32(®, BCN_TIME_CFG_BEACON_GEN, 1);
rt2800_register_write(rt2x00dev, BCN_TIME_CFG, reg);
}
return;
}
if (queue_idx > QID_HCCA && queue_idx != QID_MGMT)
return;
queue = rt2x00queue_get_queue(rt2x00dev, queue_idx);
idx = queue->index[Q_INDEX];
if (queue_idx == QID_MGMT)
qidx = 5;
else
qidx = queue_idx;
rt2800_register_write(rt2x00dev, TX_CTX_IDX(qidx), idx);
}
void rt2x00usb_kick_tx_queue(struct rt2x00_dev *rt2x00dev,
const enum data_queue_qid qid)
{
struct data_queue *queue = rt2x00queue_get_queue(rt2x00dev, qid);
unsigned long irqflags;
unsigned int index;
unsigned int index_done;
unsigned int i;
/*
* Only protect the range we are going to loop over,
* if during our loop a extra entry is set to pending
* it should not be kicked during this run, since it
* is part of another TX operation.
*/
spin_lock_irqsave(&queue->lock, irqflags);
index = queue->index[Q_INDEX];
index_done = queue->index[Q_INDEX_DONE];
spin_unlock_irqrestore(&queue->lock, irqflags);
/*
* Start from the TX done pointer, this guarentees that we will
* send out all frames in the correct order.
*/
if (index_done < index) {
for (i = index_done; i < index; i++)
rt2x00usb_kick_tx_entry(&queue->entries[i]);
} else {
for (i = index_done; i < queue->limit; i++)
rt2x00usb_kick_tx_entry(&queue->entries[i]);
for (i = 0; i < index; i++)
rt2x00usb_kick_tx_entry(&queue->entries[i]);
}
}
void rt2x00usb_kill_tx_queue(struct rt2x00_dev *rt2x00dev,
const enum data_queue_qid qid)
{
struct data_queue *queue = rt2x00queue_get_queue(rt2x00dev, qid);
struct queue_entry_priv_usb *entry_priv;
struct queue_entry_priv_usb_bcn *bcn_priv;
unsigned int i;
bool kill_guard;
/*
* When killing the beacon queue, we must also kill
* the beacon guard byte.
*/
kill_guard =
(qid == QID_BEACON) &&
(test_bit(DRIVER_REQUIRE_BEACON_GUARD, &rt2x00dev->flags));
/*
* Cancel all entries.
*/
for (i = 0; i < queue->limit; i++) {
entry_priv = queue->entries[i].priv_data;
usb_kill_urb(entry_priv->urb);
/*
* Kill guardian urb (if required by driver).
*/
if (kill_guard) {
bcn_priv = queue->entries[i].priv_data;
usb_kill_urb(bcn_priv->guardian_urb);
}
}
}
int rt2x00mac_conf_tx(struct ieee80211_hw *hw, u16 queue_idx,
const struct ieee80211_tx_queue_params *params)
{
struct rt2x00_dev *rt2x00dev = hw->priv;
struct data_queue *queue;
queue = rt2x00queue_get_queue(rt2x00dev, queue_idx);
if (unlikely(!queue))
return -EINVAL;
/*
* The passed variables are stored as real value ((2^n)-1).
* Ralink registers require to know the bit number 'n'.
*/
if (params->cw_min > 0)
queue->cw_min = fls(params->cw_min);
else
queue->cw_min = 5; /* cw_min: 2^5 = 32. */
if (params->cw_max > 0)
queue->cw_max = fls(params->cw_max);
else
queue->cw_max = 10; /* cw_min: 2^10 = 1024. */
queue->aifs = params->aifs;
queue->txop = params->txop;
INFO(rt2x00dev,
"Configured TX queue %d - CWmin: %d, CWmax: %d, Aifs: %d, TXop: %d.\n",
queue_idx, queue->cw_min, queue->cw_max, queue->aifs, queue->txop);
return 0;
}
void rt2x00usb_kill_tx_queue(struct rt2x00_dev *rt2x00dev,
const enum data_queue_qid qid)
{
struct data_queue *queue = rt2x00queue_get_queue(rt2x00dev, qid);
struct queue_entry_priv_usb *entry_priv;
struct queue_entry_priv_usb_bcn *bcn_priv;
unsigned int i;
bool kill_guard;
kill_guard =
(qid == QID_BEACON) &&
(test_bit(DRIVER_REQUIRE_BEACON_GUARD, &rt2x00dev->flags));
for (i = 0; i < queue->limit; i++) {
entry_priv = queue->entries[i].priv_data;
usb_kill_urb(entry_priv->urb);
if (kill_guard) {
bcn_priv = queue->entries[i].priv_data;
usb_kill_urb(bcn_priv->guardian_urb);
}
}
}
void rt2x00usb_kick_tx_queue(struct rt2x00_dev *rt2x00dev,
const enum data_queue_qid qid)
{
struct data_queue *queue = rt2x00queue_get_queue(rt2x00dev, qid);
unsigned long irqflags;
unsigned int index;
unsigned int index_done;
unsigned int i;
spin_lock_irqsave(&queue->lock, irqflags);
index = queue->index[Q_INDEX];
index_done = queue->index[Q_INDEX_DONE];
spin_unlock_irqrestore(&queue->lock, irqflags);
if (index_done < index) {
for (i = index_done; i < index; i++)
rt2x00usb_kick_tx_entry(&queue->entries[i]);
} else {
for (i = index_done; i < queue->limit; i++)
rt2x00usb_kick_tx_entry(&queue->entries[i]);
for (i = 0; i < index; i++)
rt2x00usb_kick_tx_entry(&queue->entries[i]);
}
}
/*
* Interrupt functions.
*/
static void rt2400pci_txdone(struct rt2x00_dev *rt2x00dev,
const enum ieee80211_tx_queue queue_idx)
{
struct data_queue *queue = rt2x00queue_get_queue(rt2x00dev, queue_idx);
struct queue_entry_priv_pci_tx *priv_tx;
struct queue_entry *entry;
struct txdone_entry_desc txdesc;
u32 word;
while (!rt2x00queue_empty(queue)) {
entry = rt2x00queue_get_entry(queue, Q_INDEX_DONE);
priv_tx = entry->priv_data;
rt2x00_desc_read(priv_tx->desc, 0, &word);
if (rt2x00_get_field32(word, TXD_W0_OWNER_NIC) ||
!rt2x00_get_field32(word, TXD_W0_VALID))
break;
/*
* Obtain the status about this packet.
*/
txdesc.status = rt2x00_get_field32(word, TXD_W0_RESULT);
txdesc.retry = rt2x00_get_field32(word, TXD_W0_RETRY_COUNT);
rt2x00pci_txdone(rt2x00dev, entry, &txdesc);
}
}
/*
* Interrupt functions.
*/
static void rt2800pci_wakeup(struct rt2x00_dev *rt2x00dev)
{
struct ieee80211_conf conf = { .flags = 0 };
struct rt2x00lib_conf libconf = { .conf = &conf };
rt2800_config(rt2x00dev, &libconf, IEEE80211_CONF_CHANGE_PS);
}
static void rt2800pci_txdone(struct rt2x00_dev *rt2x00dev)
{
struct data_queue *queue;
struct queue_entry *entry;
u32 status;
u8 qid;
while (kfifo_get(&rt2x00dev->txstatus_fifo, &status)) {
qid = rt2x00_get_field32(status, TX_STA_FIFO_PID_QUEUE);
if (qid >= QID_RX) {
/*
* Unknown queue, this shouldn't happen. Just drop
* this tx status.
*/
WARNING(rt2x00dev, "Got TX status report with "
"unexpected pid %u, dropping\n", qid);
break;
}
queue = rt2x00queue_get_queue(rt2x00dev, qid);
if (unlikely(queue == NULL)) {
/*
* The queue is NULL, this shouldn't happen. Stop
* processing here and drop the tx status
*/
WARNING(rt2x00dev, "Got TX status for an unavailable "
"queue %u, dropping\n", qid);
break;
}
if (rt2x00queue_empty(queue)) {
/*
* The queue is empty. Stop processing here
* and drop the tx status.
*/
WARNING(rt2x00dev, "Got TX status for an empty "
"queue %u, dropping\n", qid);
break;
}
entry = rt2x00queue_get_entry(queue, Q_INDEX_DONE);
rt2800_txdone_entry(entry, status);
}
}
static void rt2800pci_txstatus_tasklet(unsigned long data)
{
rt2800pci_txdone((struct rt2x00_dev *)data);
}
/*
* Interrupt functions.
*/
static void rt2400pci_txdone(struct rt2x00_dev *rt2x00dev,
const enum data_queue_qid queue_idx)
{
struct data_queue *queue = rt2x00queue_get_queue(rt2x00dev, queue_idx);
struct queue_entry_priv_pci *entry_priv;
struct queue_entry *entry;
struct txdone_entry_desc txdesc;
u32 word;
while (!rt2x00queue_empty(queue)) {
entry = rt2x00queue_get_entry(queue, Q_INDEX_DONE);
entry_priv = entry->priv_data;
rt2x00_desc_read(entry_priv->desc, 0, &word);
if (rt2x00_get_field32(word, TXD_W0_OWNER_NIC) ||
!rt2x00_get_field32(word, TXD_W0_VALID))
break;
/*
* Obtain the status about this packet.
*/
txdesc.flags = 0;
switch (rt2x00_get_field32(word, TXD_W0_RESULT)) {
case 0: /* Success */
case 1: /* Success with retry */
__set_bit(TXDONE_SUCCESS, &txdesc.flags);
break;
case 2: /* Failure, excessive retries */
__set_bit(TXDONE_EXCESSIVE_RETRY, &txdesc.flags);
/* Don't break, this is a failed frame! */
default: /* Failure */
__set_bit(TXDONE_FAILURE, &txdesc.flags);
}
txdesc.retry = rt2x00_get_field32(word, TXD_W0_RETRY_COUNT);
rt2x00lib_txdone(entry, &txdesc);
}
}
/*
* Interrupt functions.
*/
static void rt2800pci_txdone(struct rt2x00_dev *rt2x00dev)
{
struct data_queue *queue;
struct queue_entry *entry;
struct queue_entry *entry_done;
struct queue_entry_priv_pci *entry_priv;
struct txdone_entry_desc txdesc;
u32 word;
u32 reg;
u32 old_reg;
unsigned int type;
unsigned int index;
u16 mcs, real_mcs;
/*
* During each loop we will compare the freshly read
* TX_STA_FIFO register value with the value read from
* the previous loop. If the 2 values are equal then
* we should stop processing because the chance it
* quite big that the device has been unplugged and
* we risk going into an endless loop.
*/
old_reg = 0;
while (1) {
rt2800_register_read(rt2x00dev, TX_STA_FIFO, ®);
if (!rt2x00_get_field32(reg, TX_STA_FIFO_VALID))
break;
if (old_reg == reg)
break;
old_reg = reg;
/*
* Skip this entry when it contains an invalid
* queue identication number.
*/
type = rt2x00_get_field32(reg, TX_STA_FIFO_PID_TYPE) - 1;
if (type >= QID_RX)
continue;
queue = rt2x00queue_get_queue(rt2x00dev, type);
if (unlikely(!queue))
continue;
/*
* Skip this entry when it contains an invalid
* index number.
*/
index = rt2x00_get_field32(reg, TX_STA_FIFO_WCID) - 1;
if (unlikely(index >= queue->limit))
continue;
entry = &queue->entries[index];
entry_priv = entry->priv_data;
rt2x00_desc_read((__le32 *)entry->skb->data, 0, &word);
entry_done = rt2x00queue_get_entry(queue, Q_INDEX_DONE);
while (entry != entry_done) {
/*
* Catch up.
* Just report any entries we missed as failed.
*/
WARNING(rt2x00dev,
"TX status report missed for entry %d\n",
entry_done->entry_idx);
txdesc.flags = 0;
__set_bit(TXDONE_UNKNOWN, &txdesc.flags);
txdesc.retry = 0;
rt2x00lib_txdone(entry_done, &txdesc);
entry_done = rt2x00queue_get_entry(queue, Q_INDEX_DONE);
}
/*
* Obtain the status about this packet.
*/
txdesc.flags = 0;
if (rt2x00_get_field32(reg, TX_STA_FIFO_TX_SUCCESS))
__set_bit(TXDONE_SUCCESS, &txdesc.flags);
else
__set_bit(TXDONE_FAILURE, &txdesc.flags);
/*
* Ralink has a retry mechanism using a global fallback
* table. We setup this fallback table to try immediate
* lower rate for all rates. In the TX_STA_FIFO,
* the MCS field contains the MCS used for the successfull
* transmission. If the first transmission succeed,
* we have mcs == tx_mcs. On the second transmission,
* we have mcs = tx_mcs - 1. So the number of
* retry is (tx_mcs - mcs).
*/
mcs = rt2x00_get_field32(word, TXWI_W0_MCS);
real_mcs = rt2x00_get_field32(reg, TX_STA_FIFO_MCS);
__set_bit(TXDONE_FALLBACK, &txdesc.flags);
txdesc.retry = mcs - min(mcs, real_mcs);
rt2x00lib_txdone(entry, &txdesc);
}
}
int rt2x00mac_add_interface(struct ieee80211_hw *hw,
struct ieee80211_vif *vif)
{
struct rt2x00_dev *rt2x00dev = hw->priv;
struct rt2x00_intf *intf = vif_to_intf(vif);
struct data_queue *queue = rt2x00queue_get_queue(rt2x00dev, QID_BEACON);
struct queue_entry *entry = NULL;
unsigned int i;
/*
* Don't allow interfaces to be added
* the device has disappeared.
*/
if (!test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags) ||
!test_bit(DEVICE_STATE_STARTED, &rt2x00dev->flags))
return -ENODEV;
switch (vif->type) {
case NL80211_IFTYPE_AP:
/*
* We don't support mixed combinations of
* sta and ap interfaces.
*/
if (rt2x00dev->intf_sta_count)
return -ENOBUFS;
/*
* Check if we exceeded the maximum amount
* of supported interfaces.
*/
if (rt2x00dev->intf_ap_count >= rt2x00dev->ops->max_ap_intf)
return -ENOBUFS;
break;
case NL80211_IFTYPE_STATION:
case NL80211_IFTYPE_ADHOC:
case NL80211_IFTYPE_MESH_POINT:
case NL80211_IFTYPE_WDS:
/*
* We don't support mixed combinations of
* sta and ap interfaces.
*/
if (rt2x00dev->intf_ap_count)
return -ENOBUFS;
/*
* Check if we exceeded the maximum amount
* of supported interfaces.
*/
if (rt2x00dev->intf_sta_count >= rt2x00dev->ops->max_sta_intf)
return -ENOBUFS;
break;
default:
return -EINVAL;
}
/*
* Loop through all beacon queues to find a free
* entry. Since there are as much beacon entries
* as the maximum interfaces, this search shouldn't
* fail.
*/
for (i = 0; i < queue->limit; i++) {
entry = &queue->entries[i];
if (!test_and_set_bit(ENTRY_BCN_ASSIGNED, &entry->flags))
break;
}
if (unlikely(i == queue->limit))
return -ENOBUFS;
/*
* We are now absolutely sure the interface can be created,
* increase interface count and start initialization.
*/
if (vif->type == NL80211_IFTYPE_AP)
rt2x00dev->intf_ap_count++;
else
rt2x00dev->intf_sta_count++;
spin_lock_init(&intf->lock);
spin_lock_init(&intf->seqlock);
mutex_init(&intf->beacon_skb_mutex);
intf->beacon = entry;
/*
* The MAC adddress must be configured after the device
* has been initialized. Otherwise the device can reset
* the MAC registers.
* The BSSID address must only be configured in AP mode,
* however we should not send an empty BSSID address for
* STA interfaces at this time, since this can cause
* invalid behavior in the device.
*/
memcpy(&intf->mac, vif->addr, ETH_ALEN);
if (vif->type == NL80211_IFTYPE_AP) {
memcpy(&intf->bssid, vif->addr, ETH_ALEN);
rt2x00lib_config_intf(rt2x00dev, intf, vif->type,
intf->mac, intf->bssid);
} else {
rt2x00lib_config_intf(rt2x00dev, intf, vif->type,
intf->mac, NULL);
}
/*
* Some filters depend on the current working mode. We can force
* an update during the next configure_filter() run by mac80211 by
* resetting the current packet_filter state.
*/
rt2x00dev->packet_filter = 0;
return 0;
}
int rt2x00mac_tx(struct ieee80211_hw *hw, struct sk_buff *skb)
{
struct rt2x00_dev *rt2x00dev = hw->priv;
struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(skb);
enum data_queue_qid qid = skb_get_queue_mapping(skb);
struct data_queue *queue;
/*
* Mac80211 might be calling this function while we are trying
* to remove the device or perhaps suspending it.
* Note that we can only stop the TX queues inside the TX path
* due to possible race conditions in mac80211.
*/
if (!test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags))
goto exit_fail;
/*
* Determine which queue to put packet on.
*/
if (tx_info->flags & IEEE80211_TX_CTL_SEND_AFTER_DTIM &&
test_bit(DRIVER_REQUIRE_ATIM_QUEUE, &rt2x00dev->flags))
queue = rt2x00queue_get_queue(rt2x00dev, QID_ATIM);
else
queue = rt2x00queue_get_queue(rt2x00dev, qid);
if (unlikely(!queue)) {
ERROR(rt2x00dev,
"Attempt to send packet over invalid queue %d.\n"
"Please file bug report to %s.\n", qid, DRV_PROJECT);
goto exit_fail;
}
/*
* If CTS/RTS is required. create and queue that frame first.
* Make sure we have at least enough entries available to send
* this CTS/RTS frame as well as the data frame.
* Note that when the driver has set the set_rts_threshold()
* callback function it doesn't need software generation of
* either RTS or CTS-to-self frame and handles everything
* inside the hardware.
*/
if ((tx_info->control.rates[0].flags & (IEEE80211_TX_RC_USE_RTS_CTS |
IEEE80211_TX_RC_USE_CTS_PROTECT)) &&
!rt2x00dev->ops->hw->set_rts_threshold) {
if (rt2x00queue_available(queue) <= 1)
goto exit_fail;
if (rt2x00mac_tx_rts_cts(rt2x00dev, queue, skb))
goto exit_fail;
}
if (rt2x00queue_write_tx_frame(queue, skb, false))
goto exit_fail;
if (rt2x00queue_threshold(queue))
ieee80211_stop_queue(rt2x00dev->hw, qid);
return NETDEV_TX_OK;
exit_fail:
ieee80211_stop_queue(rt2x00dev->hw, qid);
dev_kfree_skb_any(skb);
return NETDEV_TX_OK;
}
/*
* Interrupt functions.
*/
static void rt2800pci_wakeup(struct rt2x00_dev *rt2x00dev)
{
struct ieee80211_conf conf = { .flags = 0 };
struct rt2x00lib_conf libconf = { .conf = &conf };
rt2800_config(rt2x00dev, &libconf, IEEE80211_CONF_CHANGE_PS);
}
static void rt2800pci_txdone(struct rt2x00_dev *rt2x00dev)
{
struct data_queue *queue;
struct queue_entry *entry;
u32 status;
u8 qid;
while (kfifo_get(&rt2x00dev->txstatus_fifo, &status)) {
qid = rt2x00_get_field32(status, TX_STA_FIFO_PID_QUEUE);
if (qid >= QID_RX) {
/*
* Unknown queue, this shouldn't happen. Just drop
* this tx status.
*/
WARNING(rt2x00dev, "Got TX status report with "
"unexpected pid %u, dropping\n", qid);
break;
}
queue = rt2x00queue_get_queue(rt2x00dev, qid);
if (unlikely(queue == NULL)) {
/*
* The queue is NULL, this shouldn't happen. Stop
* processing here and drop the tx status
*/
WARNING(rt2x00dev, "Got TX status for an unavailable "
"queue %u, dropping\n", qid);
break;
}
if (rt2x00queue_empty(queue)) {
/*
* The queue is empty. Stop processing here
* and drop the tx status.
*/
WARNING(rt2x00dev, "Got TX status for an empty "
"queue %u, dropping\n", qid);
break;
}
entry = rt2x00queue_get_entry(queue, Q_INDEX_DONE);
rt2800_txdone_entry(entry, status);
}
}
static void rt2800pci_enable_interrupt(struct rt2x00_dev *rt2x00dev,
struct rt2x00_field32 irq_field)
{
unsigned long flags;
u32 reg;
/*
* Enable a single interrupt. The interrupt mask register
* access needs locking.
*/
spin_lock_irqsave(&rt2x00dev->irqmask_lock, flags);
rt2800_register_read(rt2x00dev, INT_MASK_CSR, ®);
rt2x00_set_field32(®, irq_field, 1);
rt2800_register_write(rt2x00dev, INT_MASK_CSR, reg);
spin_unlock_irqrestore(&rt2x00dev->irqmask_lock, flags);
}
