int main(void)
{
setClock();
lcdPortConfig();
lcdInit();
clearLCD(black);
while(1)
{
if(boxes._1)
makeOpenBox(220,80,yellow);
else
makeBox(220,80,yellow);
if(boxes._2)
makeOpenBox(120,80,green);
else
makeBox(120,80,green);
if(boxes._3)
makeOpenBox(20,80,red);
else
makeBox(20,80,red);
}
}
void Clock::stopwatch()
{
mvprintw(4, 80, "Setting stopwatch...");
is24 = true;
setClock();
int input = 0;
Colon colon1(5, 30), colon2(5, 55);
bool oneSec = true;
while((input = kbinput()) != 268 && !(hr == 0 && min == 0 && sec == 0))
{
if(oneSec)
lessSec(1);
oneSec = !oneSec;
colon1.display(true);
colon2.display(true);
display(true);
}
if(hr == 0 && min == 0 && sec == 0)
{
mvprintw(4, 80, "Time's up!!");
for(int i = 0; i<7; i++)
std::cout<<(char)7;
}
else
mvprintw(4, 80, "Exiting timer");
clrtoeol();
}
void UI::initializeGame ()
{
score = 0;
level = 0;
fallInterval = 1000 - (10 * level);
totalLines = 0;
lineProgress = 0;
timeEvent = true;
keyEvent = false;
setClock ();
updateClock ();
engine = new GameEngine ();
nextPiece = new GameEngine (2, 2, 7, 6);
nextPieceCode = rand()%7;
if (nextPieceCode<3)
engine->placeNewPiece(nextPieceCode, 4, 19);
else
engine->placeNewPiece(nextPieceCode, 5, 19);
nextPieceCode = rand()%7;
nextPiece->placeNewPiece (nextPieceCode, 3, 3);
}
void TwoWire::begin(void)
{
//serial_begin(BAUD2DIV(115200));
//serial_print("\nWire Begin\n");
slave_mode = 0;
SIM_SCGC4 |= SIM_SCGC4_I2C0; // TODO: use bitband
I2C0_C1 = 0;
// On Teensy 3.0 external pullup resistors *MUST* be used
// the PORT_PCR_PE bit is ignored when in I2C mode
// I2C will not work at all without pullup resistors
// It might seem like setting PORT_PCR_PE & PORT_PCR_PS
// would enable pullup resistors. However, there seems
// to be a bug in chip while I2C is enabled, where setting
// those causes the port to be driven strongly high.
if (sda_pin_num == 18) {
CORE_PIN18_CONFIG = PORT_PCR_MUX(2)|PORT_PCR_ODE|PORT_PCR_SRE|PORT_PCR_DSE;
} else if (sda_pin_num == 17) {
CORE_PIN17_CONFIG = PORT_PCR_MUX(2)|PORT_PCR_ODE|PORT_PCR_SRE|PORT_PCR_DSE;
}
if (scl_pin_num == 19) {
CORE_PIN19_CONFIG = PORT_PCR_MUX(2)|PORT_PCR_ODE|PORT_PCR_SRE|PORT_PCR_DSE;
} else if (scl_pin_num == 16) {
CORE_PIN16_CONFIG = PORT_PCR_MUX(2)|PORT_PCR_ODE|PORT_PCR_SRE|PORT_PCR_DSE;
}
setClock(100000);
I2C0_C2 = I2C_C2_HDRS;
I2C0_C1 = I2C_C1_IICEN;
//pinMode(3, OUTPUT);
//pinMode(4, OUTPUT);
}
// Public Methods //////////////////////////////////////////////////////////////
void TwoWire::begin(uint8_t address)
{
rxBufferIndex = 0;
rxBufferLength = 0;
txBufferIndex = 0;
txBufferLength = 0;
slaveBufferIndex = 0;
slaveBufferLength = 0;
transmitting_master = false;
transmitting_slave = false;
receiving_slave = false;
SIM_HAL_EnableClock(SIM, gate_name);
PORT_CLOCK_ENABLE(sda);
PORT_CLOCK_ENABLE(scl);
PORT_BWR_PCR_ODE(PERIPH_PORT(sda), PINS_PIN(sda), true); //set as open drain
PORT_BWR_PCR_ODE(PERIPH_PORT(scl), PINS_PIN(scl), true); //set as open drain
PORT_SET_MUX_I2C(sda);
PORT_SET_MUX_I2C(scl);
I2C_HAL_Init(instance);
I2C_HAL_SetAddress7bit(instance, address);
I2C_HAL_SetStartStopIntCmd(instance, true);
I2C_HAL_SetIntCmd(instance, true);
NVIC_EnableIRQ(irqNumber);
I2C_HAL_Enable(instance);
setClock(100000);
}
//
// Constructor
//
// The pins are not activated until begin() is called.
//
SoftwareWire::SoftwareWire(uint8_t sdaPin, uint8_t sclPin, boolean pullups, boolean detectClockStretch)
{
_sdaPin = sdaPin;
_sclPin = sclPin;
_pullups = pullups;
_stretch = detectClockStretch;
setClock( 100000UL); // set default 100kHz
// Set default timeout to 1000 ms.
// 1 second is very long, 10ms would be more appropriate.
// However, the Arduino libraries use often a default timeout of 1 second.
setTimeout( 1000L);
// Turn Arduino pin numbers into PORTx, DDRx, and PINx
uint8_t port;
port = digitalPinToPort(_sdaPin);
_sdaBitMask = digitalPinToBitMask(_sdaPin);
_sdaPortReg = portOutputRegister(port);
_sdaDirReg = portModeRegister(port);
_sdaPinReg = portInputRegister(port); // PinReg is the input register, not the Arduino pin.
port = digitalPinToPort(_sclPin);
_sclBitMask = digitalPinToBitMask(_sclPin);
_sclPortReg = portOutputRegister(port);
_sclDirReg = portModeRegister(port);
_sclPinReg = portInputRegister(port);
}
Stage::Stage():_statUpdate(0), _statRender(0), _clipOuter(false), _viewport(0,0,0,0)
{
spClock clock = new Clock();
setClock(clock);
setName("Stage");
//addEventHandler(new EventHandler());
}
void UI::inGameLoop ()
{
initializeGame();
bool quit = false;
while (!quit)
{
if (keyEvent || timeEvent)
{
string canvas = buildLayout();
system ("cls");
cout << canvas;
}
updateClock ();
timeEvent = false;
keyEvent = false;
if (timePassed >= fallInterval)
{
if (engine->translatePiece (0, -1) );
else
{
int cleared = engine->clearCompleteLines();
if (cleared > 0)
{
totalLines += cleared;
lineProgress += cleared;
score += 15 * (level+1) * (calculateExpo(2 , cleared) );
}
if (lineProgress >= 10)
{
lineProgress = lineProgress - 10;
level++;
fallInterval = 1000 - (100 * level);
}
if (engine->placeNewPiece(nextPieceCode, 4, 19) )
{
nextPiece->clearPiece ();
nextPieceCode = rand()%7;
nextPiece->placeNewPiece (nextPieceCode, 3, 3);
}
else
quit = true;
}
timeEvent = true;
setClock ();
updateClock ();
}
keyEvent = keyHandler();
Sleep (1);
}
}
parallelDo()
{
cls();
Program_Num = 4;
CurrentPCBno = 1;
freeAll();
initPro();
setClock();
do2();
}
/**
\param[in] busNumber The number of the SPI bus to open (0 or 1)
\param[in] mode The SPI mode (clock polarity and phase: 0, 1, 2 or 3)
\param[in] clockKhz The clock speed to use for the SPI bus
\param[in] dataBits The size of an SPI transfer in bits
\return HRESULT success or error code.
*/
HRESULT QuarkSpiControllerClass::begin(ULONG busNumber, ULONG mode, ULONG clockKhz, ULONG dataBits)
{
HRESULT hr = S_OK;
PWCHAR deviceName = nullptr;
PVOID baseAddress = nullptr;
// If this object does not yet have the SPI bus open:
if (m_hController == INVALID_HANDLE_VALUE)
{
// Get the name of the PCI device that describes the SPI controller.
switch (busNumber)
{
case ADC_SPI_BUS:
deviceName = galileoSpi0DeviceName;
break;
case EXTERNAL_SPI_BUS:
deviceName = galileoSpi1DeviceName;
break;
default: // Only support the two SPI busses
hr = DMAP_E_SPI_BUS_REQUESTED_DOES_NOT_EXIST;
}
if (SUCCEEDED(hr))
{
// Open the Dmap device for the SPI controller.
hr = GetControllerBaseAddress(deviceName, m_hController, baseAddress);
if (SUCCEEDED(hr))
{
m_registers = (PSPI_CONTROLLER)baseAddress;
}
}
if (SUCCEEDED(hr))
{
// We now "own" the SPI controller, intialize it.
m_registers->SSCR0.ALL_BITS = 0; // Disable controller (and also clear other bits)
m_registers->SSCR0.DSS = dataBits - 1; // Use the specified data width
m_registers->SSCR1.ALL_BITS = 0; // Clear all register bits
m_registers->SSSR.ROR = 1; // Clear any RX Overrun Status bit currently set
hr = setMode(mode);
}
if (SUCCEEDED(hr))
{
hr = setClock(clockKhz);
}
}
return hr;
}
void Clock::initialize()
{
bool toggle = true;
int input = 0;
while((input = kbinput()) != 270)
{
display(toggle);
toggle = !toggle;
if(toggle)
addSec(1);
}
display(true);
setClock();
}
Stage::Stage(bool autoReset) : _statUpdate(0), _statRender(0), _clipOuter(false), _viewport(0, 0, 0, 0) //, _active(true)
{
spClock clock = new Clock();
setClock(clock);
setName("Stage");
//each mobile application should handle focus lost
//and free/restore GPU resources
if (autoReset)
{
addEventListener(Stage::DEACTIVATE, CLOSURE(this, &Stage::onDeactivate));
addEventListener(Stage::ACTIVATE, CLOSURE(this, &Stage::onActivate));
}
_stage = this;
#ifdef OXYGINE_SDL
_window = 0;
#endif
}
//run the clock state machine. call this function frequently from the main loop.
void GoldieClock::run(time_t utc)
{
static clockStates_t CLOCK_STATE;
btnSet.read();
btnIncr.read();
switch ( CLOCK_STATE)
{
case RUN_CLOCK:
if ( btnSet.pressedFor(SET_LONGPRESS) )
{
CLOCK_STATE = SET_CLOCK;
}
else if ( btnIncr.wasReleased() ) //toggle the quarter-hour rainbows
{
if ( _showRainbows = !_showRainbows )
{
rainbowCycle(2, 1); //show a rainbow if rainbow mode is on
}
else
{
clear(); //else just blank the display for a second
show();
delay(1000);
}
}
else
{
displayClock(utc);
}
break;
case SET_CLOCK:
if ( setClock() ) //returns true when setting complete
{
CLOCK_STATE = RUN_CLOCK;
}
break;
}
}
void checkSwing(float div, float del){
setDivide(div);
setDelay(del);
setDelayMode();
loop();
int cycles = divider.value*2+1;
int time = delay.value/2+1;
int ticks = delay.value-time;
int i;
for(i=0; clockIsHigh() == combinedIsHigh() && i<1000; ++i)
toggleClock();
BOOST_CHECK_EQUAL(i, cycles);
BOOST_CHECK(swinger.running == true);
BOOST_CHECK(clockIsHigh());
callTimer(time);
setClock(false);
for(i=0; !combinedIsHigh() && i<1000; ++i)
callTimer();
BOOST_CHECK_EQUAL(i, ticks);
for(i=0; combinedIsHigh() && i<1000; ++i)
callTimer();
BOOST_CHECK_EQUAL(i, time);
}
void TwoWire::begin(void)
{
//serial_begin(BAUD2DIV(115200));
//serial_print("\nWire Begin\n");
rxBufferIndex = 0;
rxBufferLength = 0;
txBufferIndex = 0;
txBufferLength = 0;
transmitting = 0;
user_onRequest = NULL;
user_onReceive = NULL;
slave_mode = 0;
hardware.clock_gate_register |= hardware.clock_gate_mask;
port().C1 = 0;
// On Teensy 3.0 external pullup resistors *MUST* be used
// the PORT_PCR_PE bit is ignored when in I2C mode
// I2C will not work at all without pullup resistors
// It might seem like setting PORT_PCR_PE & PORT_PCR_PS
// would enable pullup resistors. However, there seems
// to be a bug in chip while I2C is enabled, where setting
// those causes the port to be driven strongly high.
uint32_t mux;
volatile uint32_t *reg;
reg = portConfigRegister(hardware.sda_pin[sda_pin_index]);
mux = PORT_PCR_MUX(hardware.sda_mux[sda_pin_index]);
*reg = mux|PORT_PCR_ODE|PORT_PCR_SRE|PORT_PCR_DSE;
reg = portConfigRegister(hardware.scl_pin[scl_pin_index]);
mux = PORT_PCR_MUX(hardware.scl_mux[scl_pin_index]);
*reg = mux|PORT_PCR_ODE|PORT_PCR_SRE|PORT_PCR_DSE;
setClock(100000);
port().C2 = I2C_C2_HDRS;
port().C1 = I2C_C1_IICEN;
//pinMode(3, OUTPUT);
//pinMode(4, OUTPUT);
}
void setHours(const uint08 hours)
{
setClock(hours, getMinutes(), getSeconds());
}
void cci_process()
{
CCI_DISPLAY_ENV = request_msg_env();
MsgEnv *cci_env = request_msg_env();
MsgEnv* a_env = request_msg_env(); // this wont be released as process A will release it later
char formatted_msg[1000];
int retVal;
while(1)
{
const int twait = 500000;
cci_print("CCI: ");
//cci_env = request_msg_env();
get_console_chars(cci_env);
cci_env = receive_message();
while(cci_env->msg_type != CONSOLE_INPUT)
{
release_message_env(cci_env);
cci_env = receive_message();
}
//Obtained keyboard input
char command [MAXCHAR];
int offset = sprintf(command, cci_env->data);
// Check atleast 2 characters even if user entered 1.
if (offset < 2)
offset = 2;
// Send a message to process A. This only happens once. If it has already been sent, then prompt user.
if (strncasecmp(command, "s", offset) == 0)
{
if (a_env != NULL)
{
retVal = send_message(PROCA_ID, a_env);
if (retVal != SUCCESS)
cci_print("Failed to send message envlope and start A\n");
a_env = NULL;
}
else
{
cci_print("A has already started.\n");
}
}
else if(strncasecmp(command, "ps", offset ) == 0)
{
retVal = request_process_status(cci_env);
if (retVal != SUCCESS)
cci_print("Failed to request process status");
sprintf(formatted_msg, cci_env->data);
cci_print(formatted_msg);
}
else if(strncasecmp(command, "cd", offset) == 0)
{
displayClock(1);
}
else if(strncasecmp(command, "ct", offset) == 0)
{
displayClock(0);
}
// Display Trace Buffers
else if(strncasecmp(command, "b", offset) == 0)
{
retVal = get_trace_buffers(cci_env);
if (retVal != SUCCESS)
cci_print("Failed to get trace buffers");
sprintf(formatted_msg, "%s", cci_env->data);
cci_print(formatted_msg);
}
else if(strncasecmp(command, "c", 2) == 0)
{
if(command[4] != ':' || command[7] != ':' || strlen(command) != 10)
{
sprintf(formatted_msg, "Invalid format for command %s. It should be: c <hh>:<mm>:<ss>\n", "c");
cci_print(formatted_msg);
}
else
{
const char * rawTimeString = command+2;
char hourString [3] = { '0', '0', '\0'};
char minString [3] = { '0', '0', '\0'};
char secString [3] = { '0', '0', '\0'};
int i, hr, min, sec;
for (i=0;i<2;i++)
{
hourString[i] =rawTimeString[i];
minString[i]=rawTimeString[3+i];
secString[i]=rawTimeString[6+i];
}
hour = atoi(hourString);
min = atoi(minString);
sec = atoi(secString);
if (hour>23 || min>59 || sec > 59)
{
sprintf(formatted_msg, "Invalid input."
" Ensure hh not greater than 23, mm not greater than 59, ss not greater than 59.\n");
cci_print(formatted_msg);
}
else
setClock(hour, min, sec); // offset the "c " (c-space)
}
}
else if(strncasecmp(command, "n", 1) == 0)
{
int priority, pid;
// extract priority and pid from the command
if (sscanf(command, "%*s %i %i", &priority, &pid)!=2)
{
sprintf(formatted_msg, "Invalid format for command %s. It should be: n <priority> <process id>\n", "n");
cci_print(formatted_msg);
}
else
{
retVal = change_priority(priority, pid);
sprintf(formatted_msg, "Priority: %i, Pid: %i\n", priority, pid);
cci_print(formatted_msg);
if (retVal == ILLEGAL_ARGUMENT)
{
sprintf(formatted_msg, "Invalid arguments. Ensure that the priority is between [0-3], and the process ID is a valid"
"process ID other than the NULL process ID\n");
cci_print(formatted_msg);
}
else if (retVal != SUCCESS)
{
cci_print("Priority of specified process could not be changed\n");
}
}
}
else if(strncasecmp(command, "t", offset) == 0)
{
// no need to release envelopes as terminate will free all memory from MSG_LIST
terminate();
}
// debugging function. find where all the envelopes are.
else if(strncasecmp(command, "en", offset) == 0)
{
int offset = sprintf(formatted_msg, "\nEnvelope Num\tHeld By\n");
int i;
for (i = 0; i < MSG_ENV_COUNT; ++i)
{
const char* pcb_name;
switch(MSG_LIST[i]->dest_pid)
{
case(-1):
pcb_name = "NONE\0";
break;
default:
pcb_name = PCB_LIST[MSG_LIST[i]->dest_pid]->name;
}
offset += sprintf(formatted_msg+offset, "%i\t\t%s\n", i+1, pcb_name);
}
cci_print(formatted_msg);
}
// debugging, check all queues
else if(strncasecmp(command, "cq", offset) == 0)
{
int offset = 0;
offset += sprintf(formatted_msg, "\nREADY QUEUE");
int rdy_queues = proc_pq_get_num_prorities(RDY_PROC_QUEUE);
int i;
for (i = 0; i < rdy_queues; ++i)
{
offset+= sprintf(formatted_msg+offset, "\nPriority %i: ", i);
pcb* head = RDY_PROC_QUEUE->priority_queues[i]->head;
while (head != NULL)
{
offset += sprintf(formatted_msg+offset, "%s->", head->name);
head = head->next;
}
}
offset += sprintf(formatted_msg+offset, "\n\nBLOCKED QUEUE: ");
pcb* head = BLOCKED_QUEUE->head;
while(head!=NULL)
{
offset += sprintf(formatted_msg+offset, "%s->", head->name);
head = head->next;
}
offset += sprintf(formatted_msg + offset, "\n\n");
cci_print(formatted_msg);
}
// One space and enter results in CCI: being printed again
else if(strncasecmp(command, " ", offset) == 0)
{
}
// If enter is directly pressed, display a different error
else if(strcmp(command, "") == 0)
{
cci_print("Enter a command!\n");
}
// Default error message
else
{
sprintf(formatted_msg, "The command %s is not supported\n", command);
cci_print(formatted_msg);
}
//printf("releasing %p\n", cci_env);
//release_message_env(cci_env);
}
fflush(stdout);
printf("=====================WTH! CCI came out of while loop!");
fflush(stdout);
terminate();
}
int GPSDriverAshtech::handleMessage(int len)
{
char *endp;
if (len < 7) { return 0; }
int uiCalcComma = 0;
for (int i = 0 ; i < len; i++) {
if (_rx_buffer[i] == ',') { uiCalcComma++; }
}
char *bufptr = (char *)(_rx_buffer + 6);
int ret = 0;
if ((memcmp(_rx_buffer + 3, "ZDA,", 3) == 0) && (uiCalcComma == 6)) {
/*
UTC day, month, and year, and local time zone offset
An example of the ZDA message string is:
$GPZDA,172809.456,12,07,1996,00,00*45
ZDA message fields
Field Meaning
0 Message ID $GPZDA
1 UTC
2 Day, ranging between 01 and 31
3 Month, ranging between 01 and 12
4 Year
5 Local time zone offset from GMT, ranging from 00 through 13 hours
6 Local time zone offset from GMT, ranging from 00 through 59 minutes
7 The checksum data, always begins with *
Fields 5 and 6 together yield the total offset. For example, if field 5 is -5 and field 6 is +15, local time is 5 hours and 15 minutes earlier than GMT.
*/
double ashtech_time = 0.0;
int day = 0, month = 0, year = 0, local_time_off_hour __attribute__((unused)) = 0,
local_time_off_min __attribute__((unused)) = 0;
if (bufptr && *(++bufptr) != ',') { ashtech_time = strtod(bufptr, &endp); bufptr = endp; }
if (bufptr && *(++bufptr) != ',') { day = strtol(bufptr, &endp, 10); bufptr = endp; }
if (bufptr && *(++bufptr) != ',') { month = strtol(bufptr, &endp, 10); bufptr = endp; }
if (bufptr && *(++bufptr) != ',') { year = strtol(bufptr, &endp, 10); bufptr = endp; }
if (bufptr && *(++bufptr) != ',') { local_time_off_hour = strtol(bufptr, &endp, 10); bufptr = endp; }
if (bufptr && *(++bufptr) != ',') { local_time_off_min = strtol(bufptr, &endp, 10); bufptr = endp; }
int ashtech_hour = static_cast<int>(ashtech_time / 10000);
int ashtech_minute = static_cast<int>((ashtech_time - ashtech_hour * 10000) / 100);
double ashtech_sec = static_cast<float>(ashtech_time - ashtech_hour * 10000 - ashtech_minute * 100);
/*
* convert to unix timestamp
*/
struct tm timeinfo;
timeinfo.tm_year = year - 1900;
timeinfo.tm_mon = month - 1;
timeinfo.tm_mday = day;
timeinfo.tm_hour = ashtech_hour;
timeinfo.tm_min = ashtech_minute;
timeinfo.tm_sec = int(ashtech_sec);
#ifndef NO_MKTIME
time_t epoch = mktime(&timeinfo);
if (epoch > GPS_EPOCH_SECS) {
uint64_t usecs = static_cast<uint64_t>((ashtech_sec - static_cast<uint64_t>(ashtech_sec))) * 1000000;
// FMUv2+ boards have a hardware RTC, but GPS helps us to configure it
// and control its drift. Since we rely on the HRT for our monotonic
// clock, updating it from time to time is safe.
timespec ts;
ts.tv_sec = epoch;
ts.tv_nsec = usecs * 1000;
setClock(ts);
_gps_position->time_utc_usec = static_cast<uint64_t>(epoch) * 1000000ULL;
_gps_position->time_utc_usec += usecs;
} else {
_gps_position->time_utc_usec = 0;
}
#else
_gps_position->time_utc_usec = 0;
#endif
_last_timestamp_time = gps_absolute_time();
}
void VideoStateInfo::setClockSpeed(Clock *c, double speed) {
setClock(c, getClock(c), c->serial);
c->speed = speed;
}
void VideoStateInfo::initClock(Clock *c, int *queue_serial) {
c->speed = 1.0;
c->paused = 0;
c->queue_serial = queue_serial;
setClock(c, NAN, -1);
}
/* 测试大对象 ,loop小于 500000*/
VOID testBig(WORD page, WORD field, DWORD loop)
{
_DB_RET ret;
_db_tuple_no tupleNo;
DWORD mem, time;
_db_t_object_handle objectHandle;
initDb(page);
ret = initTable(field);
if (_DB_SUCCESS != ret)
{
printf("%d, init initTable error ret= %x\n", __LINE__, ret);
dropDb();
return;
}
/* test new */
setClock();
setMem();
for (tupleNo = 0; tupleNo < loop; ++tupleNo)
{
ret = _db_put_tuple(tranHandle, dbHandle, tableHandle, (BYTE*) record);
if (ret != _DB_SUCCESS)
{
printf("_db_put_tuple error ret= %x\n", ret);
break;
}
}
time = getUsedTimes();
mem = getUsedMem();
writeLog("testNew: ", page, field, tupleNo, mem >> 10, time);
/*delete given no object */
setClock();
for (tupleNo = 0; tupleNo < loop; ++tupleNo)
{
ret = _db_delete_tuple_by_tupleno(tranHandle, dbHandle, tableHandle, tupleNo);
if (ret != _DB_SUCCESS)
{
printf("_db_delete_tuple_by_tupleno= %x\n", ret);
break;
}
}
time = getUsedTimes();
mem = getUsedMem();
writeLog("testDelGiven: ", page, field, tupleNo, mem >> 10, time);
/*test new given */
setClock();
setMem();
for (tupleNo = 0; tupleNo < loop; ++tupleNo)
{
ret = _db_put_tuple_by_tupleno(tranHandle, dbHandle, tableHandle, (BYTE*) record, tupleNo);
if (ret != _DB_SUCCESS)
{
printf("_db_put_tuple_by_tupleno error ret= %x\n", ret);
break;
}
}
time = getUsedTimes();
mem = getUsedMem();
writeLog("testNewGiven: ", page, field, tupleNo, mem >> 10, time);
/* get given no object */
setClock();
for (tupleNo = 0; tupleNo < loop; ++tupleNo)
{
ret = _db_get_tuplehandle_by_tupleno(dbHandle, tableHandle, tupleNo, &objectHandle);
if (ret != _DB_FOUND)
{
printf("_db_get_tuplehandle_by_tupleno error ret= %x, objectNo=%d\n", ret, tupleNo);
break;
}
}
time = getUsedTimes();
writeLog("testGetGiven: ", page, field, tupleNo, mem >> 10, time);
dropDb();
}
void VideoStateInfo::updateVideoPts(double pts, int64_t pos, int serial) {
/* update current video pts */
setClock(vidClk, pts, serial);
syncClock2Slave(extClk, vidClk);
}
void VideoStateInfo::syncClock2Slave(Clock *c, Clock *slave) {
double clock = getClock(c);
double slave_clock = getClock(slave);
if (!isnan(slave_clock) && (isnan(clock) || fabs(clock - slave_clock) > AV_NOSYNC_THRESHOLD))
setClock(c, slave_clock, slave->serial);
}
int main(void)
{
int spiFd;
int fdPot;
uint32_t updateUserTick = 0;
ftmCfg_t ftmPWM = {
.mode = FTM_MODE_PWM,
.mod = 0,
.initCount = 0,
.channels = { FTM_CH_0, FTM_CH_1, FTM_CH_2,
FTM_CH_3, FTM_CH_4, FTM_CH_5,
FTM_CH_NONE},
.pwmFreq = PWM_FREQ,
.pwmCfgBits = FTM_PWM_CFG_COMBINED_MODE_CHS_0_1
| FTM_PWM_CFG_COMBINED_MODE_CHS_2_3
| FTM_PWM_CFG_COMBINED_MODE_CHS_4_5
| FTM_PWM_CFG_COMPLEMENTARY_CH_0_1
| FTM_PWM_CFG_COMPLEMENTARY_CH_2_3
| FTM_PWM_CFG_COMPLEMENTARY_CH_4_5
| FTM_PWM_CFG_OUTPUT_MASK
| FTM_PWM_CFG_CENTER_ALINGNED
,
.triggerBits = FTM_TRIGGER_INIT, /* TODO setup PDB off this trigger
* to run ADC captures of current.
*/
.deadTime = 1, /* 1/10 uSec */
.dutyScaled = { 0.6 * UNITY, 0.6 * UNITY , 0.6 * UNITY ,
0.6 * UNITY, 0.6 * UNITY , 0.6 * UNITY},
.activeLow = { TRUE, FALSE, TRUE, FALSE, TRUE, FALSE },
};
ftmCfg_t ftmCh2QD = {
.mode = FTM_MODE_QUADRATURE_DECODE,
.mod = QUAD_CALL_BACK_COUNT,
.initCount = 0,
.quadCfg = FTM_QUAD_CONFIG_FILTER_MED,
};
setClock();
uart_install();
spi_install();
adc_install();
/*
* Register the standard I/O streams with a particular deivce driver.
*/
int fd1 = fdevopen(stdout, "uart3", 0, 0);
ioctl(fd1, IO_IOCTL_UART_BAUD_SET, 115200);
assert(fd1 != -1);
gpioConfig(FET_DRIVER_ENABLE_PORT, FET_DRIVER_ENABLE_PIN,
GPIO_OUTPUT | GPIO_DSE | GPIO_PULLUP);
gpioClear(FET_DRIVER_ENABLE_PORT, FET_DRIVER_ENABLE_PIN);
gpioConfig(FET_DRIVER_RESET_PORT, FET_DRIVER_RESET_PIN,
GPIO_OUTPUT | GPIO_DSE | GPIO_PULLUP);
gpioClear(FET_DRIVER_RESET_PORT, FET_DRIVER_RESET_PIN);
gpioConfig(ENCODER_INDEX_PORT, ENCODER_INDEX_PIN, GPIO_INPUT
| GPIO_PULLUP);
#if 0
gpioConfig(HALL_A_PORT, HALL_A_PIN, GPIO_INPUT | GPIO_PULLDOWN);
gpioConfig(HALL_B_PORT, HALL_B_PIN, GPIO_INPUT | GPIO_PULLDOWN);
gpioConfig(HALL_C_PORT, HALL_C_PIN, GPIO_INPUT | GPIO_PULLDOWN);
#endif
gpioConfig(IRQ_PORT, IRQ_PIN, GPIO_INPUT | GPIO_PULLDOWN);
/* Install irq handler for driver and over current interrupts (PTA27)
* and phase B,C Hall sensors */
PORT_PCR(IRQ_PORT, IRQ_PIN) |= PORT_IRQC_INT_RISING_EDGE;
PORT_PCR(ENCODER_INDEX_PORT, ENCODER_INDEX_PIN)
|= PORT_IRQC_INT_RISING_EDGE;
#if 0
PORT_PCR(HALL_A_PORT, HALL_A_PIN) |= PORT_IRQC_INT_EITHER_EDGE;
PORT_PCR(HALL_B_PORT, HALL_B_PIN) |= PORT_IRQC_INT_EITHER_EDGE;
PORT_PCR(HALL_C_PORT, HALL_C_PIN) |= PORT_IRQC_INT_EITHER_EDGE;
#endif
hwInstallISRHandler(ISR_GPIO_A, portAIsr);
hwInstallISRHandler(ISR_GPIO_B, indexIsr);
#if 0
hwInstallISRHandler(ISR_GPIO_D, portAIsr);
#endif
/* LEDs */
gpioConfig(N_LED_ORANGE_PORT, N_LED_ORANGE_PIN, GPIO_OUTPUT | GPIO_LOW);
gpioConfig(N_LED_YELLOW_PORT, N_LED_YELLOW_PIN, GPIO_OUTPUT | GPIO_LOW);
gpioConfig(N_LED_GREEN_PORT, N_LED_GREEN_PIN, GPIO_OUTPUT | GPIO_LOW);
gpioConfig(N_LED_BLUE_PORT, N_LED_BLUE_PIN, GPIO_OUTPUT | GPIO_LOW);
/* setup pit */
pitInit(PIT_0, pit0ISR, 5000);
hwSetISRPriority(IRQ_PIT0, 0x0F);
/* setup ftm */
ftmInit(FTM_0, callBackFtm0, &ftmPWM);
#if 0
ftmInit(FTM_2, callBackFtm2, &ftmCh2QD);
#else
ftmInit(FTM_2, 0, &ftmCh2QD);
#endif
hwSetISRPriority(IRQ_FTM0, 0x0F);
hwSetISRPriority(IRQ_FTM2, 0x0F);
ftmWrite(FTM_2, 1000, 0);
/* Install spi into the device table before using it */
spiFd = open("spi2", 0, 0);
assert(spiFd != -1);
ioctl(spiFd, IO_IOCTL_SPI_SET_PORT_PCRS, 0);
ioctl(spiFd, IO_IOCTL_SPI_SET_BAUD, SPI_BAUDRATE_CLKDIV_32);
ioctl(spiFd, IO_IOCTL_SPI_SET_SCLK_MODE, SPI_SCLK_MODE_2);
ioctl(spiFd, IO_IOCTL_SPI_SET_FMSZ, 8);
ioctl(spiFd, IO_IOCTL_SPI_SET_OPTS, SPI_OPTS_MASTER);
ioctl(spiFd, IO_IOCTL_SPI_SET_CS, SPI_CS_0);
ioctl(spiFd, IO_IOCTL_SPI_SET_CS_INACT_STATE, SPI_CS_0_INACT_HIGH);
ioctl(spiFd, IO_IOCTL_SPI_SET_METHOD, SPI_METHOD_POLLED);
initFetPreDriver(FTM_0, spiFd);
/* ADC Setup */
fdPot = open("adc0", 0, 0);
if (fdPot==-1) {
assert(0);
}
ioctl(fdPot, IO_IOCTL_ADC_CALIBRATE, TRUE);
ioctl(fdPot, IO_IOCTL_ADC_SAMPLE_SIZE_SET, 1);
ioctl(fdPot, IO_IOCTL_ADC_CALL_BACK_SET, (int)potCallBackHandler);
ioctl(fdPot, IO_IOCTL_ADC_VREF_SELECT, IO_IOCTL_ADC_VREF_FLAGS_DEFAULT);
ioctl(fdPot, IO_IOCTL_ADC_TRIGGER_SELECT, IO_IOCTL_ADC_TRIGGER_SELECT_SW);
ioctl(fdPot, IO_IOCTL_ADC_CONVERSION_CONTINUOUS, TRUE);
ioctl(fdPot, IO_IOCTL_ADC_CONVERSION_TIME_SELECT,
IO_IOCTL_ADC_CONVERSION_TIME_FLAGS_ADLSTS_ADCK_2);
ioctl(fdPot, IO_IOCTL_ADC_AVERAGE_SELECT, IO_IOCTL_ADC_FLAGS_AVGS_4);
ioctl(fdPot, IO_IOCTL_ADC_RESOLUTION_SELECT, IO_IOCTL_ADC_RES_FLAGS_12_BIT);
ioctl(fdPot, IO_IOCTL_ADC_CLOCK_SELECT, IO_IOCTL_ADC_FLAGS_ADICLK_BUS);
ioctl(fdPot, IO_IOCTL_ADC_DIFFERENTIAL_SET,
(IO_IOCTL_ADC_CHANNEL_FLAGS_REGISTER_A
| IO_IOCTL_ADC_DIFF_FLAGS_SINGLE_ENDED));
ioctl(fdPot, IO_IOCTL_ADC_CHANNEL_SELECT,
(IO_IOCTL_ADC_CHANNEL_FLAGS_REGISTER_A
| (IO_IOCTL_ADC0_CHANNEL_FLAGS_ADC0_DP0
// | (IO_IOCTL_ADC1_CHANNEL_FLAGS_ADC1_DM1
& IO_IOCTL_ADC_CHANNEL_FLAGS_CH_MASK)));
hwSetISRPriority(IRQ_ADC0, 0x0A);
while(1){
switch (motorState) {
default:
/* Do nothing */
break;
case MOTOR_STATE_OFF:
/* Turn off motor outputs */
ftmSetOutputMask(FTM_0, MASK_ALL_OUTPUTS, TRUE);
taskDelay(1000);
motorState = MOTOR_STATE_ALIGN;
break;
case MOTOR_STATE_ALIGN:
{
svm_t svmAlign;
svmAlign = resolveSVM(MOTOR_ALIGN_DRIVE, 0);
ftmPwmWrite(FTM_0, FTM_CH_1, svmAlign.pwmADuty, FALSE);
ftmPwmWrite(FTM_0, FTM_CH_3, svmAlign.pwmBDuty, FALSE);
ftmPwmWrite(FTM_0, FTM_CH_5, svmAlign.pwmCDuty, FALSE);
/* Turn on motor outputs */
ftmSetOutputMask(FTM_0, MASK_NO_OUTPUTS, TRUE);
taskDelay(250);
printf("Aligning %f %f %f \n", svmAlign.pwmADuty / 32768.0,
svmAlign.pwmBDuty /32768.0, svmAlign.pwmCDuty / 32768.0);
printf("Set encoder count %d \n", ftmWrite(FTM_2, 1000, 0));
motorOutput = MOTOR_ALIGN_DRIVE;
motorState = MOTOR_STATE_RUN;
}
break;
}
if (updateFlags & UPDATE_HALT) {
updateFlags &= ~UPDATE_HALT;
break;
}
#if 0
if (tickGet() > updateStatusTick) {
updateStatusTick = tickGet() + 5;
#if 0
if (pwmRampUp) {
motorOutput += 0.0005 * UNITY;
} else {
motorOutput -= 0.0005 * UNITY;
}
if (motorOutput > 0.4 * UNITY) {
motorOutput = 0.4 * UNITY;
updateStatusTick = tickGet() + 1000;
pwmRampUp = FALSE;
} else if (motorOutput < 0.1 * UNITY) {
motorOutput = 0.1 * UNITY;
pwmRampUp = TRUE;
updateStatusTick = tickGet() + 1000;
}
#endif
}
#endif
if (tickGet() > updateUserTick) {
int count = ftmRead(FTM_2);
printf("%d,[%3.2f], %3.2f, %3.2f, 0000, "
"%d, <<%3.2f>>%3.2f, %3.2f, %3.2f\n",
// angleSetPoint / 32768.0,
count,
angleSetPoint / 32768.0,
mechTheta / 32768.0,
theta / 32768.0,
svmOutput.sinLUTIdx,
motorOutput / 32768.0,
svmOutput.pwmADuty/32768.0,
svmOutput.pwmBDuty/32768.0,
svmOutput.pwmCDuty/32768.0);
updateUserTick = tickGet() + 20;
}
}
close(fdPot);
printf("Application Fatal Error! \n");
while(1) {};
return 0;
}
void setPerf(short cpu, short mem, short gpu )
{
switch(cpu)
{
case 0:
setClock(k1008MHz_CPU);
break;
case 1:
setClock(k800MHz_CPU);
break;
default:
setClock(k1008MHz_CPU);
}
switch(mem)
{
case 0:
setClock(k200MHz_L3);
setClock(k400MHz_DDR);
break;
case 1:
setClock(k100MHz_L3);
setClock(k200MHz_DDR);
break;
default:
setClock(k200MHz_L3);
setClock(k400MHz_DDR);
}
switch(gpu)
{
case 0:
setClock(k307MHz_SGX);
break;
case 1:
setClock(k192MHz_SGX);
break;
default:
setClock(k307MHz_SGX);
}
// system("omapconf opp");
}
void initTimer(void) {
registerISR(8, timerISR); /* register ISR i vector table */
setClock(50,40); /* set clock to 200ms */
startClock(); /* start clock */
}
/**
\param[in] busNumber The number of the SPI bus to open (0 or 1)
\param[in] mode The SPI mode (clock polarity and phase: 0, 1, 2 or 3)
\param[in] clockKhz The clock speed to use for the SPI bus
\param[in] dataBits The size of an SPI transfer in bits
\return HRESULT success or error code.
*/
HRESULT BtSpiControllerClass::begin(ULONG busNumber, ULONG mode, ULONG clockKhz, ULONG dataBits)
{
HRESULT hr = S_OK;
PWCHAR deviceName = nullptr;
PVOID baseAddress = nullptr;
_SSCR0 sscr0;
_SSSR sssr;
// If this object does not yet have the SPI bus open:
if (m_hController == INVALID_HANDLE_VALUE)
{
// Get the name of the PCI device that describes the SPI controller.
switch (busNumber)
{
case EXTERNAL_SPI_BUS:
deviceName = mbmSpiDeviceName;
break;
default: // Only support one SPI bus
hr = DMAP_E_SPI_BUS_REQUESTED_DOES_NOT_EXIST;
}
if (SUCCEEDED(hr))
{
// Open the Dmap device for the SPI controller.
hr = GetControllerBaseAddress(deviceName, m_hController, baseAddress);
if (SUCCEEDED(hr))
{
m_registers = (PSPI_CONTROLLER)baseAddress;
m_registersUpper = (PSPI_CONTROLLER_UPPER)(((PBYTE)baseAddress) + SPI_CONTROLLER_UPPER_OFFSET);
}
}
if (SUCCEEDED(hr))
{
// We now "own" the SPI controller, intialize it.
sscr0.ALL_BITS = 0;
m_registers->SSCR0.ALL_BITS = sscr0.ALL_BITS; // Disable controller
sscr0.DSS = (dataBits - 1) & 0x0F; // Data width ls4bits
sscr0.EDSS = ((dataBits - 1) >> 4) & 0x01; // Data width msbit
sscr0.RIM = 1; // Mask RX FIFO Over Run interrupts
sscr0.TIM = 1; // Mask TX FIFO Under Run interrupts
m_registers->SSCR0.ALL_BITS = sscr0.ALL_BITS;
m_registers->SSCR1.ALL_BITS = 0; // Master mode, interrupts disabled
sssr.ALL_BITS = 0;
sssr.ROR = 1; // Clear any Receive Overrun int
sssr.PINT = 1; // Clear any Peripheral Trailing Byte int
sssr.TINT = 1; // Clear any Receive Time-out int
sssr.EOC = 1; // Clear any End of Chain int
sssr.TUR = 1; // Clear any Transmit FIFO Under Run int
sssr.BCE = 1; // Clear any Bit Count Error
m_registers->SSSR.ALL_BITS = sssr.ALL_BITS;
hr = setMode(mode);
}
if (SUCCEEDED(hr))
{
hr = setClock(clockKhz);
}
}
return hr;
}
void setMinutes(const uint08 minutes)
{
setClock(getHours(), minutes, getSeconds());
}
void setSeconds(const uint08 seconds)
{
setClock(getHours(), getMinutes(), seconds);
}
/**
\param[in] busNumber The number of the SPI bus to open (0 or 1)
\param[in] mode The SPI mode (clock polarity and phase: 0, 1, 2 or 3)
\param[in] clockKhz The clock speed to use for the SPI bus
\param[in] dataBits The size of an SPI transfer in bits
\return HRESULT success or error code.
*/
HRESULT BcmSpiControllerClass::begin(ULONG busNumber, ULONG mode, ULONG clockKhz, ULONG dataBits)
{
HRESULT hr = S_OK;
PWCHAR deviceName = nullptr;
PVOID baseAddress = nullptr;
_CS cs;
// If this object does not yet have the SPI bus open:
if (m_hController == INVALID_HANDLE_VALUE)
{
// Get the name of the PCI device that describes the SPI controller.
switch (busNumber)
{
case EXTERNAL_SPI_BUS:
deviceName = pi2Spi0DeviceName;
break;
case SECOND_EXTERNAL_SPI_BUS:
deviceName = pi2Spi1DeviceName;
break;
default: // Only support two SPI buses
hr = DMAP_E_SPI_BUS_REQUESTED_DOES_NOT_EXIST;
}
if (SUCCEEDED(hr))
{
// Open the Dmap device for the SPI controller for exclusive access.
hr = GetControllerBaseAddress(deviceName, m_hController, baseAddress);
if (SUCCEEDED(hr))
{
m_registers = (PSPI_CONTROLLER)baseAddress;
}
}
//
// We now "own" the SPI controller, intialize it.
//
if (SUCCEEDED(hr))
{
hr = setClock(clockKhz);
}
if (SUCCEEDED(hr))
{
hr = setMode(mode);
}
if (SUCCEEDED(hr))
{
cs.ALL_BITS = 0;
cs.CPHA = m_clockPhase;
cs.CPOL = m_clockPolarity;
cs.CLEAR = 3; // Clear both FIFOs,
cs.TA = 1; // then start transfers.
m_registers->CS.ALL_BITS = cs.ALL_BITS;
}
}
return hr;
}