uint16_t LSM9DS0_begin( LSM9DS0_t* lsm_t, LMS9DS0_Init_t* init_t )
{
#if (DEBUG0==1)
uint8_t test[8];
#endif
uint8_t gTest, xmTest;
if(init_t==NULL)
init_t = &LMS_Device_Defaults;
// Store the given scales in class variables. These scale variables
// are used throughout to calculate the actual g's, DPS,and Gs's.
lsm_t->gScale = init_t->gScl;
lsm_t->aScale = init_t->aScl;
lsm_t->mScale = init_t->mScl;
// Once we have the scale values, we can calculate the resolution
// of each sensor. That's what these functions are for. One for each sensor
calcgRes(lsm_t); // Calculate DPS / ADC tick, stored in gRes variable
calcmRes(lsm_t); // Calculate Gs / ADC tick, stored in mRes variable
calcaRes(lsm_t); // Calculate g / ADC tick, stored in aRes variable
// Now, initialize our hardware interface.
#if(LSM_I2C_SUPPORT==1)
if (lsm_t->interfaceMode == MODE_I2C) // If we're using I2C
LSM_initI2C(); // Initialize I2C
else if (lsm_t->interfaceMode == MODE_SPI) // else, if we're using SPI
#endif
//LSM_initSPI(); // Initialize SPI
// To verify communication, we can read from the WHO_AM_I register of
// each device. Store those in a variable so we can return them.
gTest = gReadByte(lsm_t,WHO_AM_I_G); // Read the gyro WHO_AM_I
xmTest = xmReadByte(lsm_t,WHO_AM_I_XM); // Read the accel/mag WHO_AM_I
// Gyro initialization stuff:
initGyro(lsm_t); // This will "turn on" the gyro. Setting up interrupts, etc.
setGyroODR(lsm_t,init_t->gODR); // Set the gyro output data rate and bandwidth.
setGyroScale(lsm_t,lsm_t->gScale); // Set the gyro range
// Accelerometer initialization stuff:
initAccel(lsm_t); // "Turn on" all axes of the accel. Set up interrupts, etc.
setAccelODR(lsm_t,init_t->aODR); // Set the accel data rate.
setAccelScale(lsm_t,lsm_t->aScale); // Set the accel range.
// Magnetometer initialization stuff:
initMag(lsm_t); // "Turn on" all axes of the mag. Set up interrupts, etc.
setMagODR(lsm_t,init_t->mODR); // Set the magnetometer output data rate.
setMagScale(lsm_t,lsm_t->mScale); // Set the magnetometer's range.
LSM9DS0_Update_Ctrl(lsm_t);
lsm_t->update=UPDATE_ON_SET;
#if (DEBUG0==1)
I2CreadBytes(lsm_t->gAddress,CTRL_REG1_G,test,5);
I2CreadBytes(lsm_t->xmAddress,CTRL_REG0_XM,test,7);
#endif
// Once everything is initialized, return the WHO_AM_I registers we read:
return (xmTest << 8) | gTest;
}
uint16_t begin(LSM9DS0_t* imu, gyro_scale gScl, accel_scale aScl,
mag_scale mScl, gyro_odr gODR, accel_odr aODR, mag_odr mODR)
{
// Store the given scales in imu struct. These scale variables
// are used throughout to calculate the actual g's, DPS,and Gs's.
imu->gScale = gScl;
imu->aScale = aScl;
imu->mScale = mScl;
// Once we have the scale values, we can calculate the resolution
// of each sensor. That's what these functions are for. One for each sensor
calcgRes(imu); // Calculate DPS / ADC tick, stored in gRes variable
calcaRes(imu); // Calculate g / ADC tick, stored in aRes variable
calcmRes(imu); // Calculate Gs / ADC tick, stored in mRes variable
// To verify communication, we can read from the WHO_AM_I register of
// each device. Store those in a variable so we can return them.
uint8_t gTest = gReadByte(imu->gyro, WHO_AM_I_G); // Read the gyro WHO_AM_I
uint8_t xmTest = xmReadByte(imu->xm, WHO_AM_I_XM); // Read the accel/mag WHO_AM_I
// Gyro initialization stuff:
initGyro(imu->gyro); // This will "turn on" the gyro. Setting up interrupts, etc.
setGyroODR(imu->gyro, gODR); // Set the gyro output data rate and bandwidth.
setGyroScale(imu, imu->gScale); // Set the gyro range
}
uint16_t LSM9DS0::begin(gyro_scale gScl, accel_scale aScl, mag_scale mScl,
gyro_odr gODR, accel_odr aODR, mag_odr mODR)
{
// Store the given scales in class variables. These scale variables
// are used throughout to calculate the actual g's, DPS,and Gs's.
gScale = gScl;
aScale = aScl;
mScale = mScl;
// Once we have the scale values, we can calculate the resolution
// of each sensor. That's what these functions are for. One for each sensor
calcgRes(); // Calculate DPS / ADC tick, stored in gRes variable
calcmRes(); // Calculate Gs / ADC tick, stored in mRes variable
calcaRes(); // Calculate g / ADC tick, stored in aRes variable
// Now, initialize our hardware interface.
if (interfaceMode == MODE_I2C) // If we're using I2C
{} //initI2C(); // Initialize I2C
else if (interfaceMode == MODE_SPI) // else, if we're using SPI
initSPI(); // Initialize SPI
// To verify communication, we can read from the WHO_AM_I register of
// each device. Store those in a variable so we can return them.
uint8_t gTest = gReadByte(WHO_AM_I_G); // Read the gyro WHO_AM_I
uint8_t xmTest = xmReadByte(WHO_AM_I_XM); // Read the accel/mag WHO_AM_I
// Gyro initialization stuff:
initGyro(); // This will "turn on" the gyro. Setting up interrupts, etc.
setGyroODR(gODR); // Set the gyro output data rate and bandwidth.
setGyroScale(gScale); // Set the gyro range
// Accelerometer initialization stuff:
initAccel(); // "Turn on" all axes of the accel. Set up interrupts, etc.
setAccelODR(aODR); // Set the accel data rate.
setAccelScale(aScale); // Set the accel range.
// Magnetometer initialization stuff:
initMag(); // "Turn on" all axes of the mag. Set up interrupts, etc.
setMagODR(mODR); // Set the magnetometer output data rate.
setMagScale(mScale); // Set the magnetometer's range.
// Once everything is initialized, return the WHO_AM_I registers we read:
return (xmTest << 8) | gTest;
}
/** Power on and prepare for general usage.
* This will activate the device and take it out of sleep mode (which must be done
* after start-up). This function also sets both the accelerometer and the gyroscope
* to their most sensitive settings, namely +/- 2g and +/- 250 degrees/sec, and sets
* the clock source to use the X Gyro for reference, which is slightly better than
* the default internal clock source.
*/
PUBLIC void initializeLSM6DS0(bool useAccel, bool useGyro) {
xAccelOffset = yAccelOffset = zAccelOffset = 0;
xGyroOffset = yGyroOffset = zGyroOffset = 0;
gyroEnabled = useGyro;
accelEnabled = useAccel;
if(gyroEnabled)
{
gScale = GYRO_FS_245DSP;
calcGyroRes();
}
if(accelEnabled)
{
aScale = ACC_FS_2G;
calcAccelRes();
}
if(testConnection())
{
resetLSM6DS0();
if(accelEnabled)
{
initAccel();
setFullScaleAccelRange(aScale);
setAccelODR(ACC_ODR_119Hz);
}
if(gyroEnabled)
{
initGyro();
setFullScaleGyroRange(gScale);
setGyroODR(GYRO_ODR_119Hz_CO_14Hz);
}
calibrateLSM6DS0(gbias,abias);
}
}
