static void smb136_set_charging_current(int set_current)
{
struct smb136_chg_data *chg = smb136_chg;
u8 data = 0;
if (set_current > 450) {
/* HC mode */
data = 0x8c;
smb136_i2c_write(chg->client, SMB_CommandA, data);
udelay(10);
/* Set charge current to 1500mA */
data = 0xf4;
smb136_i2c_write(chg->client, SMB_ChargeCurrent, data);
udelay(10);
} else {
/* USBIN 500mA mode */
data = 0x88;
smb136_i2c_write(chg->client, SMB_CommandA, data);
udelay(10);
/* Set charge current to 500mA */
data = 0x14;
smb136_i2c_write(chg->client, SMB_ChargeCurrent, data);
udelay(10);
}
pr_debug("%s: Set charging current as %dmA.\n", __func__, set_current);
}
static void smb136_i2c_write_array(struct i2c_client *client,
u8 *buf, int size)
{
int i;
for (i = 0; i < size; i += 3)
smb136_i2c_write(client, (u8) (*(buf + i)), (buf + i) + 1);
}
static ssize_t command_write(struct device *dev, struct device_attribute *attr, const char *buf, size_t size)
{
struct smb136_chg_data *chg = smb136_chg;
struct i2c_client *client = chg->client;
int v1, v2;
u8 addr, data;
printk("input data --> %s\n", buf);
if(sscanf(buf, "%x %x", &v1, &v2) == 2) {
addr = (u8) v1;
data = (u8) v2;
smb136_i2c_write(client, addr, data);
}
return size;
}
static void smb136_allow_volatile_writes(struct i2c_client *client)
{
int val, reg;
u8 data;
reg = SMB136_COMMAND_A;
val = smb136_i2c_read(client, reg, &data);
if ((val >= 0) && !(data & 0x80)) {
dev_dbg(&client->dev,
"%s : reg(0x%02x): 0x%02x", __func__, reg, data);
data |= (0x1 << 7);
if (smb136_i2c_write(client, reg, &data) < 0)
dev_err(&client->dev, "%s : error!\n", __func__);
val = smb136_i2c_read(client, reg, &data);
if (val >= 0) {
data = (u8) data;
dev_dbg(&client->dev, " => 0x%02x\n", data);
}
}
}
static void smb136_set_command(struct i2c_client *client,
int reg, int datum)
{
int val;
u8 data = 0;
val = smb136_i2c_read(client, reg, &data);
if (val >= 0) {
dev_dbg(&client->dev, "%s : reg(0x%02x): 0x%02x",
__func__, reg, data);
if (data != datum) {
data = datum;
if (smb136_i2c_write(client, reg, &data) < 0)
dev_err(&client->dev,
"%s : error!\n", __func__);
val = smb136_i2c_read(client, reg, &data);
if (val >= 0)
dev_dbg(&client->dev, " => 0x%02x\n", data);
}
}
}
ssize_t sec_hal_chg_store_attrs(struct device *dev,
const ptrdiff_t offset,
const char *buf, size_t count)
{
struct power_supply *psy = dev_get_drvdata(dev);
struct sec_charger_info *chg =
container_of(psy, struct sec_charger_info, psy_chg);
int ret = 0;
int x = 0;
u8 data = 0;
switch (offset) {
case CHG_REG:
if (sscanf(buf, "%x\n", &x) == 1) {
chg->reg_addr = x;
smb136_i2c_read(chg->client,
chg->reg_addr, &data);
chg->reg_data = data;
dev_dbg(dev, "%s: (read) addr = 0x%x, data = 0x%x\n",
__func__, chg->reg_addr, chg->reg_data);
ret = count;
}
break;
case CHG_DATA:
if (sscanf(buf, "%x\n", &x) == 1) {
data = (u8)x;
dev_dbg(dev, "%s: (write) addr = 0x%x, data = 0x%x\n",
__func__, chg->reg_addr, data);
smb136_i2c_write(chg->client,
chg->reg_addr, &data);
ret = count;
}
break;
default:
ret = -EINVAL;
break;
}
return ret;
}
static void smb136_set_charging_state(int en, int cable_status)
{
struct smb136_chg_data *chg = smb136_chg;
u8 data = 0;
if (!charger_i2c_init) {
pr_info("%s : smb136 charger IC i2c is not initialized!!\n"
, __func__);
return;
}
pr_info("%s : enable(%d), cable_status(%d)\n"
, __func__, en, cable_status);
if (en) { /* enable */
/* 2. Change USB5/1/HC Control from Pin to I2C */
smb136_i2c_write(chg->client, SMB_PinControl, 0x8);
udelay(10);
/* 1. USB 100mA Mode, USB5/1 Current Levels */
/* Prevent in-rush current */
data = 0x80;
smb136_i2c_write(chg->client, SMB_CommandA, data);
udelay(10);
/* 3. Set charge current to 100mA */
/* Prevent in-rush current */
data = 0x14;
smb136_i2c_write(chg->client, SMB_ChargeCurrent, data);
udelay(10);
/* 4. Disable Automatic Input Current Limit */
data = 0xe6;
smb136_i2c_write(chg->client, SMB_InputCurrentLimit, data);
udelay(10);
/* 4. Automatic Recharge Disabed */
data = 0x8c;
smb136_i2c_write(chg->client, SMB_ControlA, data);
udelay(10);
/* 5. Safty timer Disabled */
data = 0x28;
smb136_i2c_write(chg->client, SMB_ControlB, data);
udelay(10);
/* 6. Disable USB D+/D- Detection */
data = 0x28;
smb136_i2c_write(chg->client, SMB_OTGControl, data);
udelay(10);
/* 7. Set Output Polarity for STAT */
data = 0xCA;
smb136_i2c_write(chg->client, SMB_FloatVoltage, data);
udelay(10);
/* 9. Re-load Enable */
data = 0x4b;
smb136_i2c_write(chg->client, SMB_SafetyTimer, data);
udelay(10);
/* Enable charge */
gpio_set_value(chg->pdata->enable, 0);
switch (cable_status) {
case CABLE_TYPE_TA:
/* HC mode */
data = 0x8c;
smb136_i2c_write(chg->client, SMB_CommandA, data);
udelay(10);
/* Set charge current to 1500mA */
data = 0xf4;
smb136_i2c_write(chg->client, SMB_ChargeCurrent, data);
udelay(10);
break;
case CABLE_TYPE_STATION:
/* HC mode */
data = 0x8c;
smb136_i2c_write(chg->client, SMB_CommandA, data);
udelay(10);
/* Set charge current to 750mA */
data = 0x54;
smb136_i2c_write(chg->client, SMB_ChargeCurrent, data);
udelay(10);
/* Disable Automatic Input Current Limit,
* USBIN Current Limit to 700mA */
data = 0x06;
smb136_i2c_write(chg->client,
SMB_InputCurrentLimit, data);
udelay(10);
break;
case CABLE_TYPE_USB:
default:
/* Prevent in-rush current */
msleep(100);
/* USBIN 500mA mode */
data = 0x88;
smb136_i2c_write(chg->client, SMB_CommandA, data);
udelay(10);
/* Set charge current to 500mA */
data = 0x14;
smb136_i2c_write(chg->client, SMB_ChargeCurrent, data);
udelay(10);
break;
}
} else {
gpio_set_value(chg->pdata->enable, 1);
/* USB 100mA Mode, USB5/1 Current Levels */
/* Prevent in-rush current */
data = 0x80;
smb136_i2c_write(chg->client, SMB_CommandA, data);
udelay(10);
/* Set charge current to 100mA */
/* Prevent in-rush current */
data = 0x14;
smb136_i2c_write(chg->client, SMB_ChargeCurrent, data);
udelay(10);
}
return;
}
void smb136_set_otg_mode(int enable)
{
struct i2c_client *client = smb136_i2c_client;
u8 data;
printk("[SMB136] %s (enable : %d)\n", __func__, enable);
if(!charger_i2c_init) {
printk("%s : smb136 charger IC i2c is not initialized!!\n", __func__);
return ;
}
if(enable) // Enable OTG Mode
{
// 1. Set OTG Mode (Clear Bit5 of Pin Control)
smb136_i2c_read(client, SMB_PinControl, &data);
data &= ~(0x1 << 5);
smb136_i2c_write(client, SMB_PinControl, data);
udelay(10);
// 2. Enable OTG Mode (Set Bit1 of Command Register A)
smb136_i2c_read(client, SMB_CommandA, &data);
data |= (0x1 << 1);
smb136_i2c_write(client, SMB_CommandA, data);
udelay(10);
}
else // Re-init charger IC
{
// 1. Allow volatile writes to 00~09h, USB 500mA Mode, USB5/1 Mode
data = 0x88;
smb136_i2c_write(client, SMB_CommandA, data);
udelay(10);
// 2. Change USB5/1/HC Control from Pin to I2C
data = 0x08;
smb136_i2c_write(client, SMB_PinControl, data);
udelay(10);
// 3. Allow volatile writes to 00~09h, USB 500mA Mode, USB5/1 Mode
data = 0x88;
smb136_i2c_write(client, SMB_CommandA, data);
udelay(10);
// 4. Disable Automatic Input Current Limit
data = 0xe6;
smb136_i2c_write(client, SMB_InputCurrentLimit, data);
udelay(10);
//5. Fast Charge Current set 500mA
#ifdef CONFIG_TARGET_LOCALE_VZW
data = 0xf2;
#else
data = 0xf4;
#endif
smb136_i2c_write(client, SMB_ChargeCurrent, data);
udelay(10);
//6. Automatic Recharge Disabed
data = 0x8c;
smb136_i2c_write(client, SMB_ControlA, data);
udelay(10);
//7. Safty timer Disabled
data = 0x28;
smb136_i2c_write(client, SMB_ControlB, data);
udelay(10);
//8. Disable USB D+/D- Detection
data = 0x28;
smb136_i2c_write(client, SMB_OTGControl, data);
udelay(10);
//9. Set Output Polarity for STAT
data = 0xca;
smb136_i2c_write(client, SMB_FloatVoltage, data);
udelay(10);
//10. Re-load Enable
data = 0x4b;
smb136_i2c_write(client, SMB_SafetyTimer, data);
udelay(10);
}
smb136_test_read();
}
void smb136_charging(int source)
{
u8 data;
if(!charger_i2c_init) {
printk("%s : smb136 charger IC i2c is not initialized!!\n", __func__);
return ;
}
if(source ==DEVICE_TA)
{
//1. HC mode
data= 0x8c;
smb136_i2c_write(smb136_i2c_client,SMB_CommandA, data);
udelay(10);
// 2. Change USB5/1/HC Control from Pin to I2C
smb136_i2c_write(smb136_i2c_client, SMB_PinControl,0x8);
udelay(10);
smb136_i2c_write(smb136_i2c_client,SMB_CommandA, 0x8c);
udelay(10);
//3. Set charge current to 1500mA
#ifdef CONFIG_TARGET_LOCALE_VZW
data = 0xf2; //terminal Current 100mA
#else
data = 0xf4;
#endif
smb136_i2c_write(smb136_i2c_client,SMB_ChargeCurrent, data);
udelay(10);
}
else if(source ==DEVICE_USB)
{
// 1. USBIN 500mA mode
data= 0x88;
smb136_i2c_write(smb136_i2c_client,SMB_CommandA, data);
udelay(10);
// 2. Change USB5/1/HC Control from Pin to I2C
smb136_i2c_write(smb136_i2c_client, SMB_PinControl,0x8);
udelay(10);
smb136_i2c_write(smb136_i2c_client,SMB_CommandA, 0x88);
udelay(10);
// 3. Set charge current to 500mA
#ifdef CONFIG_TARGET_LOCALE_VZW
data = 0x12;
#else
data = 0x14;
#endif
smb136_i2c_write(smb136_i2c_client,SMB_ChargeCurrent, data);
udelay(10);
}
// 3. Disable Automatic Input Current Limit
data= 0xe6;
smb136_i2c_write(smb136_i2c_client,SMB_InputCurrentLimit, data);
udelay(10);
//4. Automatic Recharge Disabed
data = 0x8c;
smb136_i2c_write(smb136_i2c_client,SMB_ControlA, data);
udelay(10);
//5. Safty timer Disabled
data = 0x28;
smb136_i2c_write(smb136_i2c_client,SMB_ControlB, data);
udelay(10);
//6. Disable USB D+/D- Detection
data=0x28;
smb136_i2c_write(smb136_i2c_client,SMB_OTGControl, data);
udelay(10);
//7. Set Output Polarity for STAT
data=0xCA;
smb136_i2c_write(smb136_i2c_client, SMB_FloatVoltage, data);
udelay(10);
//8. Re-load Enable
data=0x4b;
smb136_i2c_write(smb136_i2c_client, SMB_SafetyTimer, data);
udelay(10);
}
static int smb136_charging(struct i2c_client *client)
{
struct smb136_chip *chg = i2c_get_clientdata(client);
u8 data = 0;
int gpio = 0;
dev_info(&client->dev, "%s : enable(%d), cable(%d)\n",
__func__, chg->is_enable, chg->cable_type);
if(chg->is_enable) {
switch(chg->cable_type)
{
case CABLE_TYPE_AC:
//1. HC mode
data = 0x8c;
smb136_i2c_write(chg->client, SMB_CommandA, data);
udelay(10);
// 2. Change USB5/1/HC Control from Pin to I2C
// 2. EN pin control - active low
smb136_i2c_write(chg->client, SMB_PinControl, 0x8);
udelay(10);
smb136_i2c_write(chg->client, SMB_CommandA, 0x8c);
udelay(10);
//3. Set charge current to 950mA, termination current to 150mA
data = 0x94;
smb136_i2c_write(chg->client, SMB_ChargeCurrent, data);
udelay(10);
break;
case CABLE_TYPE_USB:
default:
// 1. USBIN 500mA mode
data = 0x88;
smb136_i2c_write(chg->client, SMB_CommandA, data);
udelay(10);
// 2. Change USB5/1/HC Control from Pin to I2C
// 2. EN pin control - active low
smb136_i2c_write(chg->client, SMB_PinControl, 0x8);
udelay(10);
smb136_i2c_write(chg->client, SMB_CommandA, 0x88);
udelay(10);
// 3. Set charge current to 500mA, termination current to 150mA
data = 0x14;
smb136_i2c_write(chg->client, SMB_ChargeCurrent, data);
udelay(10);
break;
}
// 3. Enable Automatic Input Current Limit to 1000mA (threshold 4.25V)
data = 0x60;
smb136_i2c_write(chg->client, SMB_InputCurrentLimit, data);
udelay(10);
//4. Automatic Recharge Disabed
data = 0x8c;
smb136_i2c_write(chg->client, SMB_ControlA, data);
udelay(10);
//5. Safty timer Disabled
data = 0x28;
smb136_i2c_write(chg->client, SMB_ControlB, data);
udelay(10);
//6. Disable USB D+/D- Detection
data = 0x28;
smb136_i2c_write(chg->client, SMB_OTGControl, data);
udelay(10);
//7. Set Output Polarity for STAT
//7. Set float voltage to 4.2V
data = 0x4a;
smb136_i2c_write(chg->client, SMB_FloatVoltage, data);
udelay(10);
//8. Re-load Enable
data = 0x4b;
smb136_i2c_write(chg->client, SMB_SafetyTimer, data);
udelay(10);
}
else {
// do nothing...
}
/* CHG_EN pin control - active low */
gpio = gpio_request(chg->pdata->gpio_chg_en, "CHG_EN");
if (!gpio) {
gpio_direction_output(chg->pdata->gpio_chg_en, !(chg->is_enable));
dev_info(&client->dev,
"gpio(CHG_EN)is %d\n", gpio_get_value(chg->pdata->gpio_chg_en));
gpio_free(chg->pdata->gpio_chg_en);
} else
dev_err(&client->dev,
"faile to request gpio(CHG_EN)\n");
/* smb136_test_read(client); */
return 0;
}
int smb136_charging(int en, int cable_status)
{
struct smb136_chg_data *chg = smb136_chg;
u8 data = 0;
if(!charger_i2c_init) {
printk("%s : smb136 charger IC i2c is not initialized!!\n", __func__);
return -1;
}
printk("%s : enable(%d), cable_status(%d)\n",__func__,en, cable_status);
if(en) { // enable
if(cable_status==CABLE_TYPE_AC)
{
//1. HC mode
data = 0x88; // usb host plug detect only works if 0x88 fixme, we want 0x8c for HC mode
smb136_i2c_write(chg->client, SMB_CommandA, data);
udelay(10);
// 2. Change USB5/1/HC Control from Pin to I2C
smb136_i2c_write(chg->client, SMB_PinControl, 0x8);
udelay(10);
smb136_i2c_write(chg->client, SMB_CommandA, data);
udelay(10);
//3. Set charge current to 1500mA
data = 0xf4;
smb136_i2c_write(chg->client, SMB_ChargeCurrent, data);
udelay(10);
}
else if(cable_status==CABLE_TYPE_USB || cable_status==CABLE_TYPE_IMPROPER_AC)
{
// 1. USBIN 500mA mode
data = 0x88;
smb136_i2c_write(chg->client, SMB_CommandA, data);
udelay(10);
// 2. Change USB5/1/HC Control from Pin to I2C
smb136_i2c_write(chg->client, SMB_PinControl, 0x8);
udelay(10);
smb136_i2c_write(chg->client, SMB_CommandA, data);
udelay(10);
// 3. Set charge current to 500mA
data = 0x14;
smb136_i2c_write(chg->client, SMB_ChargeCurrent, data);
udelay(10);
}
// 3. Disable Automatic Input Current Limit
data = 0xe6;
smb136_i2c_write(chg->client, SMB_InputCurrentLimit, data);
udelay(10);
//4. Automatic Recharge Disabed
data = 0x8c;
smb136_i2c_write(chg->client, SMB_ControlA, data);
udelay(10);
//5. Safty timer Disabled
data = 0x28;
smb136_i2c_write(chg->client, SMB_ControlB, data);
udelay(10);
//6. Disable USB D+/D- Detection
data = 0x28;
smb136_i2c_write(chg->client, SMB_OTGControl, data);
udelay(10);
//7. Set Output Polarity for STAT
data = 0xCA;
smb136_i2c_write(chg->client, SMB_FloatVoltage, data);
udelay(10);
//8. Re-load Enable
data = 0x4b;
smb136_i2c_write(chg->client, SMB_SafetyTimer, data);
udelay(10);
}
else {
// do nothing...
}
return 0;
}
static void smb136_charger_function_conrol(
struct i2c_client *client)
{
struct sec_charger_info *charger = i2c_get_clientdata(client);
u8 data;
u8 cur_reg;
u8 chg_cur_reg;
if (charger->charging_current < 0) {
dev_dbg(&client->dev,
"%s : OTG is activated. Ignore command!\n", __func__);
return;
}
smb136_allow_volatile_writes(client);
if (charger->cable_type ==
POWER_SUPPLY_TYPE_BATTERY) {
/* turn off charger */
smb136_set_command(client,
SMB136_COMMAND_A, 0x80);
} else {
/* Pre-charge curr 250mA */
dev_dbg(&client->dev,
"%s : fast charging current (%dmA)\n",
__func__, charger->charging_current);
dev_dbg(&client->dev,
"%s : termination current (%dmA)\n",
__func__, charger->pdata->charging_current[
charger->cable_type].full_check_current_1st);
smb136_i2c_read(client, SMB136_CHARGE_CURRENT, &chg_cur_reg);
chg_cur_reg &= 0x18;
data = smb136_get_fast_charging_current_data(
charger->charging_current) | chg_cur_reg;
data |= smb136_get_termination_current_limit_data(
charger->pdata->charging_current[
charger->cable_type].full_check_current_1st);
smb136_set_command(client,
SMB136_CHARGE_CURRENT, data);
/* Pin enable control */
/* DCIN Input Pre-bias Enable */
smb136_i2c_read(client, SMB136_PIN_ENABLE_CONTROL, &data);
if (charger->pdata->chg_gpio_en)
data |= 0x40;
smb136_set_command(client,
SMB136_PIN_ENABLE_CONTROL, data);
/* Input current limit */
dev_dbg(&client->dev, "%s : input current (%dmA)\n",
__func__, charger->pdata->charging_current
[charger->cable_type].input_current_limit);
data = 0;
data = smb136_get_input_current_limit_data(
charger,
charger->pdata->charging_current
[charger->cable_type].input_current_limit);
smb136_i2c_read(client, SMB136_INPUT_CURRENTLIMIT, &cur_reg);
data |= (cur_reg & 0xF);
smb136_set_command(client,
SMB136_INPUT_CURRENTLIMIT, data);
/* Float voltage, Vprechg : 2.4V */
dev_dbg(&client->dev, "%s : float voltage (%dmV)\n",
__func__, charger->pdata->chg_float_voltage);
data = 0;
data |= smb136_get_float_voltage_data(
charger->pdata->chg_float_voltage);
smb136_set_command(client,
SMB136_FLOAT_VOLTAGE, data);
/* 4. Automatic Recharge Disabed */
data = 0x8C;
smb136_i2c_write(client, SMB136_CHARGE_CONTROL_A, &data);
/* 5. Safty timer Disabled */
data = 0x28;
smb136_i2c_write(client, SMB136_CHARGE_CONTROL_B, &data);
/* 6. Disable USB D+/D- Detection */
data = 0x28;
smb136_i2c_write(client, SMB136_OTG_CONTROL, &data);
/* 9. Re-load Enable */
data = 0x4B;
smb136_i2c_write(client, SMB136_SAFTY, &data);
/* HC or USB5 mode */
smb136_i2c_read(client, SMB136_COMMAND_A, &data);
data &= 0xF3;
switch (charger->cable_type) {
case POWER_SUPPLY_TYPE_MAINS:
case POWER_SUPPLY_TYPE_MISC:
/* High-current mode */
data |= 0x0C;
break;
case POWER_SUPPLY_TYPE_USB:
case POWER_SUPPLY_TYPE_USB_DCP:
case POWER_SUPPLY_TYPE_USB_CDP:
case POWER_SUPPLY_TYPE_USB_ACA:
/* USB5 */
data |= 0x08;
break;
default:
/* USB1 */
data = 0x00;
break;
}
smb136_set_command(client,
SMB136_COMMAND_A, data);
}
}
