C++ (Cpp) spiOut示例

示例#1

文件： Adafruit_STMPE610.cpp 项目： KurtE/Adafruit_STMPE610

uint16_t Adafruit_STMPE610::readRegister16(uint8_t reg) {
  uint16_t x;
  if (_CS == -1) {
   // use i2c
    Wire.beginTransmission(_i2caddr);
    Wire.write((byte)reg);
    Wire.endTransmission();
    Wire.requestFrom(_i2caddr, (byte)2);
    x = Wire.read();
    x<<=8;
    x |= Wire.read();
    Wire.endTransmission();

  } if (_CLK == -1) {
    // hardware SPI
#if defined (SPI_HAS_TRANSACTION)
    if (_CLK == -1) SPI.beginTransaction(mySPISettings);
#endif
    digitalWrite(_CS, LOW);
    spiOut(0x80 | reg); 
    spiOut(0x00);
    x = spiIn(); 
    x<<=8;
    x |= spiIn(); 
    digitalWrite(_CS, HIGH);
#if defined (SPI_HAS_TRANSACTION)
    if (_CLK == -1) SPI.endTransaction();
#endif
  }

  //Serial.print("$"); Serial.print(reg, HEX); 
  //Serial.print(": 0x"); Serial.println(x, HEX);
  return x;
}

示例#2

文件： SpiLcd.cpp 项目： DigitalWarrior/brewpi-avr

void SpiLcd::pulseEnable(void) {
	bitSet(_spiByte, LCD_SHIFT_ENABLE);
	spiOut();
	delayMicroseconds(1); // enable pulse must be >450ns
	bitClear(_spiByte, LCD_SHIFT_ENABLE);
	spiOut();
}

示例#3

文件： Adafruit_STMPE610.cpp 项目： wbsimms/Edison_Eclipse

void Adafruit_STMPE610::writeRegister8(uint8_t reg, uint8_t val) {
	spi_begin();
    CSLow();
    spiOut(reg); 
    spiOut(val);
    CSHigh();
    spi_end();
}

示例#4

文件： Adafruit_STMPE610.cpp 项目： wbsimms/Edison_Eclipse

uint8_t Adafruit_STMPE610::readRegister8(uint8_t reg) {
	uint8_t x ;
	spi_begin();
	CSLow();
	spiOut(0x80 | reg);
	spiOut(0x00);
	x = spiIn();
	CSHigh();
	spi_end();
	return x;
}

示例#5

文件： Adafruit_STMPE610.cpp 项目： wbsimms/Edison_Eclipse

uint16_t Adafruit_STMPE610::readRegister16(uint8_t reg) {
  uint16_t x;
	spi_begin();
    CSLow();
    spiOut(0x80 | reg); 
    spiOut(0x00);
    x = spiIn(); 
    x<<=8;
    x |= spiIn(); 
    CSHigh();
    spi_end();
  //Serial.print("$"); Serial.print(reg, HEX); 
  //Serial.print(": 0x"); Serial.println(x, HEX);
  return x;
}

示例#6

文件： SpiLcd.cpp 项目： DigitalWarrior/brewpi-avr

void SpiLcd::begin(uint8_t cols, uint8_t lines) {
	_numlines = lines;
	_currline = 0;
	_currpos = 0;
  
	// Set all outputs of shift register to low, this turns the backlight ON.
	_spiByte = 0x00;
	spiOut();
	
	// The following initialization sequence should be compatible with: 
	// - Newhaven OLED displays
	// - Standard HD44780 or S6A0069 LCD displays
	delayMicroseconds(50000); // wait 50 ms just to be sure that the lcd is initialized

	write4bits(0x03); //set to 8-bit
	delayMicroseconds(50000); // wait > 4.1ms
	write4bits(0x03); //set to 8-bit
	delayMicroseconds(1000); // wait > 100us
	write4bits(0x03); //set to 8-bit
	delayMicroseconds(50000); // wait for execution
	write4bits(0x02); //set to 4-bit
	delayMicroseconds(50000); // wait for execution
	command(0x28); // set to 4-bit, 2-line
		
	clear();	// display clear
	// Entry Mode Set:
	leftToRight();
	noAutoscroll();
	
	home();
	
	//noCursor();
	display();
}

示例#7

文件： Adafruit_STMPE610.cpp 项目： KurtE/Adafruit_STMPE610

void Adafruit_STMPE610::writeRegister8(uint8_t reg, uint8_t val) {
  if (_CS == -1) {
    // use i2c
    Wire.beginTransmission(_i2caddr);
    Wire.write((byte)reg);
    Wire.write(val);
    Wire.endTransmission();
  } else { 
#if defined (SPI_HAS_TRANSACTION)
    if (_CLK == -1) SPI.beginTransaction(mySPISettings);
#endif
    digitalWrite(_CS, LOW);
    spiOut(reg); 
    spiOut(val);
    digitalWrite(_CS, HIGH);
#if defined (SPI_HAS_TRANSACTION)
    if (_CLK == -1) SPI.endTransaction();
#endif
  }
}

示例#8

文件： SpiLcd.cpp 项目： DigitalWarrior/brewpi-avr

// write either command or data
void SpiLcd::send(uint8_t value, uint8_t mode) {
	if(mode){
		bitSet(_spiByte, LCD_SHIFT_RS);
	}
	else{
		bitClear(_spiByte, LCD_SHIFT_RS);
	}
	spiOut();
	write4bits(value>>4);
	write4bits(value);
}

示例#9

文件： SpiLcd.cpp 项目： DigitalWarrior/brewpi-avr

void SpiLcd::write4bits(uint8_t value) {
		
	_spiByte = (_spiByte & ~LCD_SHIFT_DATA_MASK) | (value << 4);
	spiOut();
	pulseEnable();
}