/**
* @brief Internal TAL reset function
*
* @param set_default_pib Defines whether PIB values need to be set
* to its default values
*
* @return MAC_SUCCESS if the transceiver state is changed to TRX_OFF and the
* current device part number and version number are correct;
* FAILURE otherwise
*/
static retval_t internal_tal_reset(bool set_default_pib)
{
if (trx_reset() != MAC_SUCCESS)
{
return FAILURE;
}
/*
* Generate a seed for the random number generator in function rand().
* This is required (for example) as seed for the CSMA-CA algorithm.
*/
tal_generate_rand_seed();
/* Configure the transceiver register values. */
trx_config();
if (set_default_pib)
{
/* Set the default PIB values */
init_tal_pib(); /* implementation can be found in 'tal_pib.c' */
}
else
{
/* nothing to do - the current TAL PIB attribute values are used */
}
/*
* Write all PIB values to the transceiver
* that are needed by the transceiver itself.
*/
write_all_tal_pib_to_trx(); /* implementation can be found in 'tal_pib.c' */
/* Reset TAL variables. */
tal_state = TAL_IDLE;
#ifdef BEACON_SUPPORT
tal_csma_state = CSMA_IDLE;
#endif /* BEACON_SUPPORT */
#if ((MAC_START_REQUEST_CONFIRM == 1) && (defined BEACON_SUPPORT))
tal_beacon_transmission = false;
#endif /* ((MAC_START_REQUEST_CONFIRM == 1) && (defined BEACON_SUPPORT)) */
tal_rx_on_required = false;
return MAC_SUCCESS;
}
static trx_retval_t internal_tal_reset(void)
{
if (trx_reset() != TRX_SUCCESS) {
return TRX_FAILURE;
}
/* Write the transceiver values except of the CSMA seed. */
trx_config();
/*
* Generate a seed for the random number generator in function rand().
* This is required (for example) as seed for the CSMA-CA algorithm.
*/
generate_rand_seed();
/* Reset TAL variables. */
tal_state = TAL_IDLE;
return TRX_SUCCESS;
}
/**
* @brief Resets TAL state machine and sets the default PIB values if requested
*
* @param trx_id Transceiver identifier
* @param set_default_pib Defines whether PIB values need to be set
* to its default values
*
* @return
* - @ref MAC_SUCCESS if the transceiver state is changed to TRX_OFF
* - @ref FAILURE otherwise
* @ingroup apiTalApi
*/
retval_t tal_reset(trx_id_t trx_id, bool set_default_pib)
{
rf_cmd_state_t previous_trx_state[NUM_TRX];
previous_trx_state[RF09] = trx_state[RF09];
previous_trx_state[RF24] = trx_state[RF24];
/* Reset the actual device or part of the device */
if (trx_reset(trx_id) != MAC_SUCCESS) {
return FAILURE;
}
/* Init Trx if necessary, e.g. trx was in deep sleep */
if (((previous_trx_state[RF09] == RF_SLEEP) &&
(previous_trx_state[RF24] == RF_SLEEP)) ||
(trx_id == RFBOTH)) {
trx_init(); /* Initialize generic trx functionality */
}
if (trx_id == RFBOTH) {
for (uint8_t i = 0; i < NUM_TRX; i++) {
/* Clean TAL and removed any pending tasks */
cleanup_tal((trx_id_t)i);
/* Configure the transceiver register values. */
trx_config((trx_id_t)i);
if (set_default_pib) {
/* Set the default PIB values */
init_tal_pib((trx_id_t)i); /* see 'tal_pib.c' */
calculate_pib_values(trx_id);
} else {
/* nothing to do - the current TAL PIB attribute
*values are used */
}
write_all_tal_pib_to_trx((trx_id_t)i); /* see
*'tal_pib.c' */
config_phy((trx_id_t)i);
/* Reset TAL variables. */
tal_state[(trx_id_t)i] = TAL_IDLE;
tx_state[(trx_id_t)i] = TX_IDLE;
#ifdef ENABLE_FTN_PLL_CALIBRATION
/* Stop FTN timer */
stop_ftn_timer((trx_id_t)i);
#endif /* ENABLE_FTN_PLL_CALIBRATION */
}
} else {
/* Maintain other trx */
trx_id_t other_trx_id;
if (trx_id == RF09) {
other_trx_id = RF24;
} else {
other_trx_id = RF09;
}
if (tal_state[other_trx_id] == TAL_SLEEP) {
/* Switch other trx back to sleep again */
uint16_t reg_offset = RF_BASE_ADDR_OFFSET *
other_trx_id;
#ifdef IQ_RADIO
pal_dev_reg_write(RF215_BB, reg_offset + RG_RF09_CMD,
RF_SLEEP);
pal_dev_reg_write(RF215_RF, reg_offset + RG_RF09_CMD,
RF_SLEEP);
#else
trx_reg_write(reg_offset + RG_RF09_CMD, RF_SLEEP);
#endif
TAL_RF_IRQ_CLR_ALL(trx_id);
}
/* Clean TAL and removed any pending tasks */
cleanup_tal(trx_id);
/* Configure the transceiver register values. */
trx_config(trx_id);
if (set_default_pib) {
/* Set the default PIB values */
init_tal_pib(trx_id); /* see 'tal_pib.c' */
calculate_pib_values(trx_id);
} else {
/* nothing to do - the current TAL PIB attribute values
*are used */
}
write_all_tal_pib_to_trx(trx_id); /* see 'tal_pib.c' */
config_phy(trx_id);
/* Reset TAL variables. */
tal_state[trx_id] = TAL_IDLE;
tx_state[trx_id] = TX_IDLE;
#ifdef ENABLE_FTN_PLL_CALIBRATION
/* Stop FTN timer */
stop_ftn_timer(trx_id);
#endif /* ENABLE_FTN_PLL_CALIBRATION */
}
/*
* Configure interrupt handling.
* Install a handler for the transceiver interrupt.
*/
#ifdef IQ_RADIO
trx_irq_init(RF215_BB, bb_irq_handler_cb);
trx_irq_init(RF215_RF, rf_irq_handler_cb);
pal_trx_irq_en(RF215_BB); /* Enable transceiver main interrupt. */
pal_trx_irq_en(RF215_RF); /* Enable transceiver main interrupt. */
#else
trx_irq_init((FUNC_PTR)trx_irq_handler_cb);
pal_trx_irq_en(); /* Enable transceiver main interrupt. */
#endif
return MAC_SUCCESS;
}
/**
* @brief Initializes the TAL
*
* This function is called to initialize the TAL. The transceiver is
* initialized, the TAL PIBs are set to their default values, and the TAL state
* machine is set to TAL_IDLE state.
*
* @return MAC_SUCCESS if the transceiver state is changed to TRX_OFF and the
* current device part number and version number are correct;
* FAILURE otherwise
*/
retval_t tal_init(void)
{
/* Init the PAL and by this means also the transceiver interface */
if (pal_init() != MAC_SUCCESS) {
return FAILURE;
}
/* Reset trx */
if (trx_reset(RFBOTH) != MAC_SUCCESS) {
return FAILURE;
}
/* Check if RF215 is connected */
if ((trx_reg_read( RG_RF_PN) != 0x34) ||
(trx_reg_read( RG_RF_VN) != 0x01)) {
return FAILURE;
}
/* Initialize trx */
trx_init();
if (tal_timer_init() != MAC_SUCCESS) {
return FAILURE;
}
/* Initialize the buffer management */
bmm_buffer_init();
/* Configure both trx and set default PIB values */
for (uint8_t trx_id = 0; trx_id < NUM_TRX; trx_id++) {
/* Configure transceiver */
trx_config((trx_id_t)trx_id);
#ifdef RF215V1
/* Calibrate LO */
calibrate_LO((trx_id_t)trx_id);
#endif
/* Set the default PIB values */
init_tal_pib((trx_id_t)trx_id); /* see 'tal_pib.c' */
calculate_pib_values((trx_id_t)trx_id);
/*
* Write all PIB values to the transceiver
* that are needed by the transceiver itself.
*/
write_all_tal_pib_to_trx((trx_id_t)trx_id); /* see 'tal_pib.c'
**/
config_phy((trx_id_t)trx_id);
tal_rx_buffer[trx_id] = bmm_buffer_alloc(LARGE_BUFFER_SIZE);
if (tal_rx_buffer[trx_id] == NULL) {
return FAILURE;
}
/* Init incoming frame queue */
qmm_queue_init(&tal_incoming_frame_queue[trx_id]);
tal_state[trx_id] = TAL_IDLE;
tx_state[trx_id] = TX_IDLE;
}
/* Init seed of rand() */
tal_generate_rand_seed();
#ifndef DISABLE_IEEE_ADDR_CHECK
for (uint8_t trx_id = 0; trx_id < 2; trx_id++) {
/* Check if a valid IEEE address is available. */
/*
* This while loop is on purpose, since just in the
* rare case that such an address is randomly
* generated again, we must repeat this.
*/
while ((tal_pib[trx_id].IeeeAddress == 0x0000000000000000) ||
(tal_pib[trx_id].IeeeAddress ==
((uint64_t)-1))) {
/*
* In case no valid IEEE address is available, a random
* IEEE address will be generated to be able to run the
* applications for demonstration purposes.
* In production code this can be omitted.
*/
/*
* The proper seed for function rand() has already been
*generated
* in function tal_generate_rand_seed().
*/
uint8_t *ptr_pib
= (uint8_t *)&tal_pib[trx_id].IeeeAddress;
for (uint8_t i = 0; i < 8; i++) {
*ptr_pib++ = (uint8_t)rand();
/*
* Note:
* Even if casting the 16 bit rand value back to
*8 bit,
* and running the loop 8 timers (instead of
*only 4 times)
* may look cumbersome, it turns out that the
*code gets
* smaller using 8-bit here.
* And timing is not an issue at this place...
*/
}
}
}
#endif
#ifdef IQ_RADIO
/* Init BB IRQ handler */
pal_trx_irq_flag_clr(RF215_BB);
trx_irq_init(RF215_BB, bb_irq_handler_cb);
pal_trx_irq_en(RF215_BB);
/* Init RF IRQ handler */
pal_trx_irq_flag_clr(RF215_RF);
trx_irq_init(RF215_RF, rf_irq_handler_cb);
pal_trx_irq_en(RF215_RF);
#else
/*
* Configure interrupt handling.
* Install a handler for the radio and the baseband interrupt.
*/
pal_trx_irq_flag_clr();
trx_irq_init((FUNC_PTR)trx_irq_handler_cb);
pal_trx_irq_en(); /* Enable transceiver main interrupt. */
#endif
#if ((defined SUPPORT_FSK) && (defined SUPPORT_MODE_SWITCH))
init_mode_switch();
#endif
return MAC_SUCCESS;
} /* tal_init() */
