/*
* Routine: misc_init_r
* Description: Configure board specific parts
*/
int misc_init_r(void)
{
struct gpio *gpio5_base = (struct gpio *)OMAP34XX_GPIO5_BASE;
struct gpio *gpio6_base = (struct gpio *)OMAP34XX_GPIO6_BASE;
struct control_prog_io *prog_io_base = (struct control_prog_io *)OMAP34XX_CTRL_BASE;
/* Enable i2c2 pullup resisters */
writel(~(PRG_I2C2_PULLUPRESX), &prog_io_base->io1);
switch (get_board_revision()) {
case REVISION_AXBX:
printf("Beagle Rev Ax/Bx\n");
setenv("beaglerev", "AxBx");
break;
case REVISION_CX:
printf("Beagle Rev C1/C2/C3\n");
setenv("beaglerev", "Cx");
MUX_BEAGLE_C();
break;
case REVISION_C4:
printf("Beagle Rev C4\n");
setenv("beaglerev", "C4");
MUX_BEAGLE_C();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
break;
case REVISION_XM_A:
printf("Beagle xM Rev A\n");
setenv("beaglerev", "xMA");
MUX_BEAGLE_XM();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
break;
case REVISION_XM_B:
printf("Beagle xM Rev B\n");
setenv("beaglerev", "xMB");
MUX_BEAGLE_XM();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
break;
case REVISION_XM_C:
printf("Beagle xM Rev C\n");
setenv("beaglerev", "xMC");
MUX_BEAGLE_XM();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
break;
default:
printf("Beagle unknown 0x%02x\n", get_board_revision());
MUX_BEAGLE_XM();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
}
switch (get_expansion_id()) {
case TINCANTOOLS_ZIPPY:
printf("Recognized Tincantools Zippy board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_TINCANTOOLS_ZIPPY();
setenv("buddy", "zippy");
break;
case TINCANTOOLS_ZIPPY2:
printf("Recognized Tincantools Zippy2 board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_TINCANTOOLS_ZIPPY();
setenv("buddy", "zippy2");
break;
case TINCANTOOLS_TRAINER:
printf("Recognized Tincantools Trainer board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_TINCANTOOLS_ZIPPY();
MUX_TINCANTOOLS_TRAINER();
setenv("buddy", "trainer");
break;
case TINCANTOOLS_SHOWDOG:
printf("Recognized Tincantools Showdow board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
/* Place holder for DSS2 definition for showdog lcd */
setenv("defaultdisplay", "showdoglcd");
setenv("buddy", "showdog");
break;
case KBADC_BEAGLEFPGA:
printf("Recognized KBADC Beagle FPGA board\n");
MUX_KBADC_BEAGLEFPGA();
setenv("buddy", "beaglefpga");
break;
case LW_BEAGLETOUCH:
printf("Recognized Liquidware BeagleTouch board\n");
setenv("buddy", "beagletouch");
break;
case BRAINMUX_LCDOG:
printf("Recognized Brainmux LCDog board\n");
setenv("buddy", "lcdog");
break;
case BRAINMUX_LCDOGTOUCH:
printf("Recognized Brainmux LCDog Touch board\n");
setenv("buddy", "lcdogtouch");
break;
case BBTOYS_WIFI:
printf("Recognized BeagleBoardToys WiFi board\n");
MUX_BBTOYS_WIFI()
setenv("buddy", "bbtoys-wifi");
break;;
case BBTOYS_VGA:
printf("Recognized BeagleBoardToys VGA board\n");
break;;
case BBTOYS_LCD:
printf("Recognized BeagleBoardToys LCD board\n");
break;;
case BCT_BRETTL3:
printf("Recognized bct electronic GmbH brettl3 board\n");
break;
case BEAGLE_NO_EEPROM:
printf("No EEPROM on expansion board\n");
setenv("buddy", "none");
break;
default:
printf("Unrecognized expansion board: %x\n",
expansion_config.device_vendor);
setenv("buddy", "unknown");
}
if (expansion_config.content == 1)
setenv(expansion_config.env_var, expansion_config.env_setting);
twl4030_power_init();
switch (get_board_revision()) {
case REVISION_XM_A:
case REVISION_XM_B:
twl4030_led_init(TWL4030_LED_LEDEN_LEDBON);
break;
default:
twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
break;
}
/* Set GPIO states before they are made outputs */
writel(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1,
&gpio6_base->setdataout);
writel(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
GPIO15 | GPIO14 | GPIO13 | GPIO12, &gpio5_base->setdataout);
/* Configure GPIOs to output */
writel(~(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1), &gpio6_base->oe);
writel(~(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
GPIO15 | GPIO14 | GPIO13 | GPIO12), &gpio5_base->oe);
dieid_num_r();
beagle_dvi_pup();
beagle_display_init();
omap3_dss_enable();
return 0;
}
/*
* Routine: misc_init_r
* Description: Configure board specific parts
*/
int misc_init_r(void)
{
unsigned int expansion_id;
twl4030_power_init();
twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
printf("Board revision: %d\n", get_board_revision());
switch (get_sdio2_config()) {
case 0:
puts("Tranceiver detected on mmc2\n");
MUX_OVERO_SDIO2_TRANSCEIVER();
break;
case 1:
puts("Direct connection on mmc2\n");
MUX_OVERO_SDIO2_DIRECT();
break;
default:
puts("Unable to detect mmc2 connection type\n");
}
expansion_id = get_expansion_id();
switch (expansion_id) {
case GUMSTIX_SUMMIT:
printf("Recognized Summit expansion board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_GUMSTIX();
setenv("defaultdisplay", "dvi");
setenv("expansionname", "summit");
break;
case GUMSTIX_TOBI:
printf("Recognized Tobi expansion board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_GUMSTIX();
setenv("defaultdisplay", "dvi");
setenv("expansionname", "tobi");
break;
case GUMSTIX_TOBI_DUO:
printf("Recognized Tobi Duo expansion board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_GUMSTIX();
setenv("expansionname", "tobiduo");
break;
case GUMSTIX_PALO35:
printf("Recognized Palo35 expansion board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_GUMSTIX();
setenv("defaultdisplay", "lcd35");
setenv("expansionname", "palo35");
break;
case GUMSTIX_PALO43:
printf("Recognized Palo43 expansion board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_GUMSTIX();
setenv("defaultdisplay", "lcd43");
setenv("expansionname", "palo43");
break;
case GUMSTIX_CHESTNUT43:
printf("Recognized Chestnut43 expansion board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_GUMSTIX();
setenv("defaultdisplay", "lcd43");
setenv("expansionname", "chestnut43");
break;
case GUMSTIX_PINTO:
printf("Recognized Pinto expansion board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_GUMSTIX();
break;
case GUMSTIX_GALLOP43:
printf("Recognized Gallop43 expansion board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_GUMSTIX();
setenv("defaultdisplay", "lcd43");
setenv("expansionname", "gallop43");
break;
case GUMSTIX_ALTO35:
printf("Recognized Alto35 expansion board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_GUMSTIX();
MUX_ALTO35();
setenv("defaultdisplay", "lcd35");
setenv("expansionname", "alto35");
break;
case GUMSTIX_STAGECOACH:
printf("Recognized Stagecoach expansion board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_GUMSTIX();
break;
case GUMSTIX_THUMBO:
printf("Recognized Thumbo expansion board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_GUMSTIX();
break;
case GUMSTIX_TURTLECORE:
printf("Recognized Turtlecore expansion board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_GUMSTIX();
break;
case GUMSTIX_ARBOR43C:
printf("Recognized Arbor43C expansion board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_GUMSTIX();
MUX_ARBOR43C();
setenv("defaultdisplay", "lcd43");
setenv("expansionname", "arbor43c");
break;
case ETTUS_USRP_E:
printf("Recognized Ettus Research USRP-E (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_GUMSTIX();
MUX_USRP_E();
setenv("defaultdisplay", "dvi");
break;
case GUMSTIX_NO_EEPROM:
case GUMSTIX_EMPTY_EEPROM:
puts("No or empty EEPROM on expansion board\n");
MUX_GUMSTIX();
setenv("expansionname", "tobi");
break;
default:
printf("Unrecognized expansion board 0x%08x\n", expansion_id);
break;
}
if (expansion_config.content == 1)
setenv(expansion_config.env_var, expansion_config.env_setting);
omap_die_id_display();
if (get_cpu_family() == CPU_OMAP34XX)
setenv("boardname", "overo");
else
setenv("boardname", "overo-storm");
return 0;
}
/*
* Routine: misc_init_r
* Description: Configure board specific parts
*/
int misc_init_r(void)
{
struct gpio *gpio5_base = (struct gpio *)OMAP34XX_GPIO5_BASE;
struct gpio *gpio6_base = (struct gpio *)OMAP34XX_GPIO6_BASE;
struct control_prog_io *prog_io_base = (struct control_prog_io *)OMAP34XX_CTRL_BASE;
bool generate_fake_mac = false;
u32 value;
/* Enable i2c2 pullup resisters */
value = readl(&prog_io_base->io1);
value &= ~(PRG_I2C2_PULLUPRESX);
writel(value, &prog_io_base->io1);
printf("WINGZ energy \nIoT group \n CDAC Bangalore\n");
setenv("musb", "musb_hdrc.fifo_mode=5");
MUX_WINGZ_C();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
if (expansion_config.content == 1)
setenv(expansion_config.env_var, expansion_config.env_setting);
twl4030_power_init();
twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
/* Set GPIO states before they are made outputs */
writel(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1,
&gpio6_base->setdataout);
writel(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
GPIO15 | GPIO14 | GPIO13 | GPIO12, &gpio5_base->setdataout);
/* Configure GPIOs to output */
writel(~(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1), &gpio6_base->oe);
writel(~(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
GPIO15 | GPIO14 | GPIO13 | GPIO12), &gpio5_base->oe);
dieid_num_r();
#ifdef CONFIG_VIDEO_OMAP3
gpio_request(170, "dvi");
gpio_direction_output(170, 0);
gpio_set_value(170, 1);
//beagle_display_init();
omap3_dss_venc_config(&venc_config_std_tv, VENC_HEIGHT, VENC_WIDTH);
omap3_dss_panel_config(&dvid_cfg);
omap3_dss_enable();
#endif
#ifdef CONFIG_USB_MUSB_OMAP2PLUS
musb_register(&musb_plat, &musb_board_data, (void *)MUSB_BASE);
#endif
if (generate_fake_mac) {
u32 id[4];
get_dieid(id);
usb_fake_mac_from_die_id(id);
}
return 0;
}
/*
* Routine: misc_init_r
* Description: Configure board specific parts
*/
int misc_init_r(void)
{
twl4030_power_init();
twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
#if defined(CONFIG_CMD_NET)
setup_net_chip();
#endif
printf("Board revision: %d\n", get_board_revision());
switch (get_sdio2_config()) {
case 0:
printf("Tranceiver detected on mmc2\n");
MUX_OVERO_SDIO2_TRANSCEIVER();
break;
case 1:
printf("Direct connection on mmc2\n");
MUX_OVERO_SDIO2_DIRECT();
break;
default:
printf("Unable to detect mmc2 connection type\n");
}
switch (get_expansion_id()) {
case GUMSTIX_SUMMIT:
printf("Recognized Summit expansion board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
setenv("defaultdisplay", "dvi");
break;
case GUMSTIX_TOBI:
printf("Recognized Tobi expansion board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
setenv("defaultdisplay", "dvi");
break;
case GUMSTIX_TOBI_DUO:
printf("Recognized Tobi Duo expansion board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
break;
case GUMSTIX_PALO35:
printf("Recognized Palo35 expansion board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
setenv("defaultdisplay", "lcd35");
break;
case GUMSTIX_PALO43:
printf("Recognized Palo43 expansion board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
setenv("defaultdisplay", "lcd43");
break;
case GUMSTIX_CHESTNUT43:
printf("Recognized Chestnut43 expansion board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
setenv("defaultdisplay", "lcd43");
break;
case GUMSTIX_PINTO:
printf("Recognized Pinto expansion board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
break;
case GUMSTIX_GALLOP43:
printf("Recognized Gallop43 expansion board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
setenv("defaultdisplay", "lcd43");
break;
case ETTUS_USRP_E:
printf("Recognized Ettus Research USRP-E (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_USRP_E();
setenv("defaultdisplay", "dvi");
break;
case GUMSTIX_NO_EEPROM:
printf("No EEPROM on expansion board\n");
break;
default:
printf("Unrecognized expansion board\n");
}
if (expansion_config.content == 1)
setenv(expansion_config.env_var, expansion_config.env_setting);
dieid_num_r();
return 0;
}
/*
* Routine: misc_init_r
* Description: Configure board specific parts
*/
int misc_init_r(void)
{
struct gpio *gpio5_base = (struct gpio *)OMAP34XX_GPIO5_BASE;
struct gpio *gpio6_base = (struct gpio *)OMAP34XX_GPIO6_BASE;
/*
* Configure drive strength for IO cells
*/
*(ulong *)(CONTROL_PROG_IO1) &= ~(PRG_I2C2_PULLUPRESX);
beagle_identify();
twl4030_power_init();
twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
switch (beagle_revision) {
case REVISION_AXBX:
printf("Beagle Rev Ax/Bx\n");
setenv("mpurate", "600");
break;
case REVISION_CX:
printf("Beagle Rev C1/C2/C3\n");
MUX_BEAGLE_C();
setenv("mpurate", "600");
break;
case REVISION_C4:
printf("Beagle Rev C4\n");
MUX_BEAGLE_C();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
setenv("mpurate", "720");
break;
case REVISION_XM:
printf("Beagle xM Rev A\n");
MUX_BEAGLE_XM();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
setenv("mpurate", "1000");
break;
default:
printf("Beagle unknown 0x%02x\n", beagle_revision);
}
/* Configure GPIOs to output */
writel(~(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1), &gpio6_base->oe);
writel(~(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
GPIO15 | GPIO14 | GPIO13 | GPIO12), &gpio5_base->oe);
/* Set GPIOs */
writel(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1,
&gpio6_base->setdataout);
writel(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
GPIO15 | GPIO14 | GPIO13 | GPIO12, &gpio5_base->setdataout);
dieid_num_r();
return 0;
}
/*
* Routine: misc_init_r
* Description: Configure board specific parts
*/
int misc_init_r(void)
{
struct gpio *gpio5_base = (struct gpio *)OMAP34XX_GPIO5_BASE;
struct gpio *gpio6_base = (struct gpio *)OMAP34XX_GPIO6_BASE;
struct control_prog_io *prog_io_base = (struct control_prog_io *)OMAP34XX_CTRL_BASE;
bool generate_fake_mac = false;
u32 value;
/* Enable i2c2 pullup resisters */
value = readl(&prog_io_base->io1);
value &= ~(PRG_I2C2_PULLUPRESX);
writel(value, &prog_io_base->io1);
switch (get_board_revision()) {
case REVISION_AXBX:
printf("Beagle Rev Ax/Bx\n");
env_set("beaglerev", "AxBx");
break;
case REVISION_CX:
printf("Beagle Rev C1/C2/C3\n");
env_set("beaglerev", "Cx");
MUX_BEAGLE_C();
break;
case REVISION_C4:
printf("Beagle Rev C4\n");
env_set("beaglerev", "C4");
MUX_BEAGLE_C();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
break;
case REVISION_XM_AB:
printf("Beagle xM Rev A/B\n");
env_set("beaglerev", "xMAB");
MUX_BEAGLE_XM();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
generate_fake_mac = true;
break;
case REVISION_XM_C:
printf("Beagle xM Rev C\n");
env_set("beaglerev", "xMC");
MUX_BEAGLE_XM();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
generate_fake_mac = true;
break;
default:
printf("Beagle unknown 0x%02x\n", get_board_revision());
MUX_BEAGLE_XM();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
generate_fake_mac = true;
}
switch (get_expansion_id()) {
case TINCANTOOLS_ZIPPY:
printf("Recognized Tincantools Zippy board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_TINCANTOOLS_ZIPPY();
env_set("buddy", "zippy");
break;
case TINCANTOOLS_ZIPPY2:
printf("Recognized Tincantools Zippy2 board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_TINCANTOOLS_ZIPPY();
env_set("buddy", "zippy2");
break;
case TINCANTOOLS_TRAINER:
printf("Recognized Tincantools Trainer board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
MUX_TINCANTOOLS_ZIPPY();
MUX_TINCANTOOLS_TRAINER();
env_set("buddy", "trainer");
break;
case TINCANTOOLS_SHOWDOG:
printf("Recognized Tincantools Showdow board (rev %d %s)\n",
expansion_config.revision,
expansion_config.fab_revision);
/* Place holder for DSS2 definition for showdog lcd */
env_set("defaultdisplay", "showdoglcd");
env_set("buddy", "showdog");
break;
case KBADC_BEAGLEFPGA:
printf("Recognized KBADC Beagle FPGA board\n");
MUX_KBADC_BEAGLEFPGA();
env_set("buddy", "beaglefpga");
break;
case LW_BEAGLETOUCH:
printf("Recognized Liquidware BeagleTouch board\n");
env_set("buddy", "beagletouch");
break;
case BRAINMUX_LCDOG:
printf("Recognized Brainmux LCDog board\n");
env_set("buddy", "lcdog");
break;
case BRAINMUX_LCDOGTOUCH:
printf("Recognized Brainmux LCDog Touch board\n");
env_set("buddy", "lcdogtouch");
break;
case BBTOYS_WIFI:
printf("Recognized BeagleBoardToys WiFi board\n");
MUX_BBTOYS_WIFI()
env_set("buddy", "bbtoys-wifi");
break;
case BBTOYS_VGA:
printf("Recognized BeagleBoardToys VGA board\n");
break;
case BBTOYS_LCD:
printf("Recognized BeagleBoardToys LCD board\n");
break;
case BCT_BRETTL3:
printf("Recognized bct electronic GmbH brettl3 board\n");
break;
case BCT_BRETTL4:
printf("Recognized bct electronic GmbH brettl4 board\n");
break;
case LSR_COM6L_ADPT:
printf("Recognized LSR COM6L Adapter Board\n");
MUX_BBTOYS_WIFI()
env_set("buddy", "lsr-com6l-adpt");
break;
case BEAGLE_NO_EEPROM:
printf("No EEPROM on expansion board\n");
env_set("buddy", "none");
break;
default:
printf("Unrecognized expansion board: %x\n",
expansion_config.device_vendor);
env_set("buddy", "unknown");
}
if (expansion_config.content == 1)
env_set(expansion_config.env_var, expansion_config.env_setting);
twl4030_power_init();
switch (get_board_revision()) {
case REVISION_XM_AB:
twl4030_led_init(TWL4030_LED_LEDEN_LEDBON);
break;
default:
twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
break;
}
/* Set GPIO states before they are made outputs */
writel(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1,
&gpio6_base->setdataout);
writel(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
GPIO15 | GPIO14 | GPIO13 | GPIO12, &gpio5_base->setdataout);
/* Configure GPIOs to output */
writel(~(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1), &gpio6_base->oe);
writel(~(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
GPIO15 | GPIO14 | GPIO13 | GPIO12), &gpio5_base->oe);
omap_die_id_display();
#ifdef CONFIG_VIDEO_OMAP3
beagle_dvi_pup();
beagle_display_init();
omap3_dss_enable();
#endif
#ifdef CONFIG_USB_MUSB_OMAP2PLUS
musb_register(&musb_plat, &musb_board_data, (void *)MUSB_BASE);
#endif
if (generate_fake_mac)
omap_die_id_usbethaddr();
#if defined(CONFIG_MTDIDS_DEFAULT) && defined(CONFIG_MTDPARTS_DEFAULT)
if (strlen(CONFIG_MTDIDS_DEFAULT))
env_set("mtdids", CONFIG_MTDIDS_DEFAULT);
if (strlen(CONFIG_MTDPARTS_DEFAULT))
env_set("mtdparts", CONFIG_MTDPARTS_DEFAULT);
#endif
return 0;
}
/*
* Routine: misc_init_r
* Description: Configure board specific parts
*/
int misc_init_r(void)
{
printf("Board revision: ");
switch (get_board_revision()) {
case 0:
case 1:
switch (get_sdio2_config()) {
case 0:
printf(" 0\n");
MUX_OVERO_SDIO2_TRANSCEIVER();
break;
case 1:
printf(" 1\n");
MUX_OVERO_SDIO2_DIRECT();
break;
default:
printf(" unknown\n");
}
break;
default:
printf(" unsupported\n");
}
switch (get_expansion_id()) {
case GUMSTIX_SUMMIT:
printf("Recognized Summit expansion board (rev %d %s)\n",
expansion_config.revision, expansion_config.fab_revision);
setenv("defaultdisplay", "dvi");
break;
case GUMSTIX_TOBI:
printf("Recognized Tobi expansion board (rev %d %s)\n",
expansion_config.revision, expansion_config.fab_revision);
setenv("defaultdisplay", "dvi");
break;
case GUMSTIX_TOBI_DUO:
printf("Recognized Tobi Duo expansion board (rev %d %s)\n",
expansion_config.revision, expansion_config.fab_revision);
break;
case GUMSTIX_PALO35:
printf("Recognized Palo 35 expansion board (rev %d %s)\n",
expansion_config.revision, expansion_config.fab_revision);
setenv("defaultdisplay", "lcd35");
break;
case GUMSTIX_PALO43:
printf("Recognized Palo 43 expansion board (rev %d %s)\n",
expansion_config.revision, expansion_config.fab_revision);
setenv("defaultdisplay", "lcd43");
break;
case GUMSTIX_CHESTNUT43:
printf("Recognized Chestnut 43 expansion board (rev %d %s)\n",
expansion_config.revision, expansion_config.fab_revision);
setenv("defaultdisplay", "lcd43");
break;
case GUMSTIX_PINTO:
printf("Recognized Pinto expansion board (rev %d %s)\n",
expansion_config.revision, expansion_config.fab_revision);
break;
case GUMSTIX_NO_EEPROM:
printf("No EEPROM on expansion board\n");
break;
default:
printf("Unrecognized expansion board\n");
}
if (expansion_config.content == 1)
setenv(expansion_config.env_var, expansion_config.env_setting);
i2c_set_bus_num(TWL4030_I2C_BUS);
twl4030_power_init();
twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
#if defined(CONFIG_CMD_NET)
setup_net_chip();
#endif
dieid_num_r();
return 0;
}
/*
* Routine: misc_init_r
* Description: Configure board specific parts
*/
int misc_init_r(void)
{
struct gpio *gpio5_base = (struct gpio *)OMAP34XX_GPIO5_BASE;
struct gpio *gpio6_base = (struct gpio *)OMAP34XX_GPIO6_BASE;
beagle_identify();
printf("\nProbing for expansion boards, if none are connected you'll see a harmless I2C error.\n");
printf("u-boot TAMATAR!\n\n");
switch (get_expansion_id()) {
case TINCANTOOLS_ZIPPY:
printf("Recognized Tincantools Zippy expansion board (rev %d %s)\n",
expansion_config.revision, expansion_config.fab_revision);
MUX_TINCANTOOLS_ZIPPY();
setenv("buddy", "zippy");
break;
case TINCANTOOLS_ZIPPY2:
printf("Recognized Tincantools Zippy2 expansion board (rev %d %s)\n",
expansion_config.revision, expansion_config.fab_revision);
MUX_TINCANTOOLS_ZIPPY();
setenv("buddy", "zippy2");
break;
case TINCANTOOLS_TRAINER:
printf("Recognized Tincantools Trainer expansion board (rev %d %s)\n",
expansion_config.revision, expansion_config.fab_revision);
MUX_TINCANTOOLS_ZIPPY();
MUX_TINCANTOOLS_TRAINER();
setenv("buddy", "trainer");
break;
case TINCANTOOLS_SHOWDOG:
printf("Recognized Tincantools Showdow expansion board (rev %d %s)\n",
expansion_config.revision, expansion_config.fab_revision);
/* Place holder for DSS2 definition for showdog lcd */
setenv("defaultdisplay", "showdoglcd");
setenv("buddy", "showdog");
break;
case KBADC_BEAGLEFPGA:
printf("Recognized KBADC Beagle FPGA board\n");
MUX_KBADC_BEAGLEFPGA();
setenv("buddy", "beaglefpga");
break;
case BEAGLE_NO_EEPROM:
printf("No EEPROM on expansion board\n");
setenv("buddy", "none");
break;
default:
printf("Unrecognized expansion board: %x\n", expansion_config.device_vendor);
setenv("buddy", "unknown");
}
if (expansion_config.content == 1)
setenv(expansion_config.env_var, expansion_config.env_setting);
i2c_set_bus_num(TWL4030_I2C_BUS);
twl4030_power_init();
twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
display_init();
switch (beagle_revision) {
case REVISION_AXBX:
printf("Beagle Rev Ax/Bx\n");
setenv("mpurate", "600");
setenv("beaglerev", "AxBx");
break;
case REVISION_CX:
printf("Beagle Rev C1/C2/C3\n");
MUX_BEAGLE_C();
setenv("mpurate", "600");
setenv("beaglerev", "Cx");
break;
case REVISION_C4:
printf("Beagle Rev C4\n");
setenv("beaglerev", "Cx");
MUX_BEAGLE_C();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
setenv("mpurate", "720");
break;
case REVISION_XM:
printf("Beagle xM Rev A\n");
setenv("beaglerev", "xMA");
MUX_BEAGLE_XM();
/* Set VAUX2 to 1.8V for EHCI PHY */
twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
TWL4030_PM_RECEIVER_DEV_GRP_P1);
setenv("mpurate", "1000");
break;
default:
printf("Beagle unknown 0x%02x\n", beagle_revision);
}
/* Configure GPIOs to output */
writel(~(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1), &gpio6_base->oe);
writel(~(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
GPIO15 | GPIO14 | GPIO13 | GPIO12), &gpio5_base->oe);
/* Set GPIOs */
writel(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1,
&gpio6_base->setdataout);
writel(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
GPIO15 | GPIO14 | GPIO13 | GPIO12, &gpio5_base->setdataout);
dieid_num_r();
omap3_dss_enable();
return 0;
}
