static int buddha_ack_intr(ide_hwif_t *hwif)
{
unsigned char ch;
ch = z_readb(hwif->io_ports[IDE_IRQ_OFFSET]);
if (!(ch & 0x80))
return 0;
return 1;
}
static int buddha_ack_intr(ide_hwif_t *hwif)
{
unsigned char ch;
ch = z_readb(hwif->io_ports.irq_addr);
if (!(ch & 0x80))
return 0;
return 1;
}
static int gayle_ack_intr_a4000(ide_hwif_t *hwif)
{
unsigned char ch;
ch = z_readb(hwif->io_ports.irq_addr);
if (!(ch & GAYLE_IRQ_IDE))
return 0;
return 1;
}
static void zorro8390_block_output(struct net_device *dev, int count,
const unsigned char *buf,
const int start_page)
{
int nic_base = NE_BASE;
unsigned long dma_start;
short *ptrs;
int cnt;
/* Round the count up for word writes. Do we need to do this?
* What effect will an odd byte count have on the 8390?
* I should check someday.
*/
if (count & 0x01)
count++;
/* This *shouldn't* happen.
* If it does, it's the last thing you'll see
*/
if (ei_status.dmaing) {
netdev_err(dev, "%s: DMAing conflict [DMAstat:%d][irqlock:%d]\n",
__func__, ei_status.dmaing, ei_status.irqlock);
return;
}
ei_status.dmaing |= 0x01;
/* We should already be in page 0, but to be safe... */
z_writeb(E8390_PAGE0+E8390_START+E8390_NODMA, nic_base + NE_CMD);
z_writeb(ENISR_RDC, nic_base + NE_EN0_ISR);
/* Now the normal output. */
z_writeb(count & 0xff, nic_base + NE_EN0_RCNTLO);
z_writeb(count >> 8, nic_base + NE_EN0_RCNTHI);
z_writeb(0x00, nic_base + NE_EN0_RSARLO);
z_writeb(start_page, nic_base + NE_EN0_RSARHI);
z_writeb(E8390_RWRITE + E8390_START, nic_base + NE_CMD);
ptrs = (short *)buf;
for (cnt = 0; cnt < count >> 1; cnt++)
z_writew(*ptrs++, NE_BASE + NE_DATAPORT);
dma_start = jiffies;
while ((z_readb(NE_BASE + NE_EN0_ISR) & ENISR_RDC) == 0)
if (time_after(jiffies, dma_start + 2 * HZ / 100)) {
/* 20ms */
netdev_warn(dev, "timeout waiting for Tx RDC\n");
zorro8390_reset_8390(dev);
__NS8390_init(dev, 1);
break;
}
z_writeb(ENISR_RDC, nic_base + NE_EN0_ISR); /* Ack intr */
ei_status.dmaing &= ~0x01;
}
static int xsurf_ack_intr(ide_hwif_t *hwif)
{
unsigned char ch;
ch = z_readb(hwif->io_ports[IDE_IRQ_OFFSET]);
/* X-Surf needs a 0 written to IRQ register to ensure ISA bit A11 stays at 0 */
z_writeb(0, hwif->io_ports[IDE_IRQ_OFFSET]);
if (!(ch & 0x80))
return 0;
return 1;
}
/* Hard reset the card. This used to pause for the same period that a
* 8390 reset command required, but that shouldn't be necessary.
*/
static void zorro8390_reset_8390(struct net_device *dev)
{
unsigned long reset_start_time = jiffies;
struct ei_device *ei_local = netdev_priv(dev);
netif_dbg(ei_local, hw, dev, "resetting - t=%ld...\n", jiffies);
z_writeb(z_readb(NE_BASE + NE_RESET), NE_BASE + NE_RESET);
ei_status.txing = 0;
ei_status.dmaing = 0;
/* This check _should_not_ be necessary, omit eventually. */
while ((z_readb(NE_BASE + NE_EN0_ISR) & ENISR_RESET) == 0)
if (time_after(jiffies, reset_start_time + 2 * HZ / 100)) {
netdev_warn(dev, "%s: did not complete\n", __func__);
break;
}
z_writeb(ENISR_RESET, NE_BASE + NE_EN0_ISR); /* Ack intr */
}
static int zorro8390_init(struct net_device *dev, unsigned long board,
const char *name, void __iomem *ioaddr)
{
int i;
int err;
unsigned char SA_prom[32];
int start_page, stop_page;
struct ei_device *ei_local = netdev_priv(dev);
static u32 zorro8390_offsets[16] = {
0x00, 0x02, 0x04, 0x06, 0x08, 0x0a, 0x0c, 0x0e,
0x10, 0x12, 0x14, 0x16, 0x18, 0x1a, 0x1c, 0x1e,
};
/* Reset card. Who knows what dain-bramaged state it was left in. */
{
unsigned long reset_start_time = jiffies;
z_writeb(z_readb(ioaddr + NE_RESET), ioaddr + NE_RESET);
while ((z_readb(ioaddr + NE_EN0_ISR) & ENISR_RESET) == 0)
if (time_after(jiffies,
reset_start_time + 2 * HZ / 100)) {
netdev_warn(dev, "not found (no reset ack)\n");
return -ENODEV;
}
z_writeb(0xff, ioaddr + NE_EN0_ISR); /* Ack all intr. */
}
/* Read the 16 bytes of station address PROM.
* We must first initialize registers,
* similar to NS8390_init(eifdev, 0).
* We can't reliably read the SAPROM address without this.
* (I learned the hard way!).
*/
{
static const struct {
u32 value;
u32 offset;
} program_seq[] = {
{E8390_NODMA + E8390_PAGE0 + E8390_STOP, NE_CMD},
/* Select page 0 */
{0x48, NE_EN0_DCFG}, /* 0x48: Set byte-wide access */
{0x00, NE_EN0_RCNTLO}, /* Clear the count regs */
{0x00, NE_EN0_RCNTHI},
{0x00, NE_EN0_IMR}, /* Mask completion irq */
{0xFF, NE_EN0_ISR},
{E8390_RXOFF, NE_EN0_RXCR}, /* 0x20 Set to monitor */
{E8390_TXOFF, NE_EN0_TXCR}, /* 0x02 and loopback mode */
{32, NE_EN0_RCNTLO},
{0x00, NE_EN0_RCNTHI},
{0x00, NE_EN0_RSARLO}, /* DMA starting at 0x0000 */
{0x00, NE_EN0_RSARHI},
{E8390_RREAD + E8390_START, NE_CMD},
};
for (i = 0; i < ARRAY_SIZE(program_seq); i++)
z_writeb(program_seq[i].value,
ioaddr + program_seq[i].offset);
}
for (i = 0; i < 16; i++) {
SA_prom[i] = z_readb(ioaddr + NE_DATAPORT);
(void)z_readb(ioaddr + NE_DATAPORT);
}
/* We must set the 8390 for word mode. */
z_writeb(0x49, ioaddr + NE_EN0_DCFG);
start_page = NESM_START_PG;
stop_page = NESM_STOP_PG;
dev->base_addr = (unsigned long)ioaddr;
dev->irq = IRQ_AMIGA_PORTS;
/* Install the Interrupt handler */
i = request_irq(IRQ_AMIGA_PORTS, __ei_interrupt,
IRQF_SHARED, DRV_NAME, dev);
if (i)
return i;
for (i = 0; i < ETH_ALEN; i++)
dev->dev_addr[i] = SA_prom[i];
pr_debug("Found ethernet address: %pM\n", dev->dev_addr);
ei_status.name = name;
ei_status.tx_start_page = start_page;
ei_status.stop_page = stop_page;
ei_status.word16 = 1;
ei_status.rx_start_page = start_page + TX_PAGES;
ei_status.reset_8390 = zorro8390_reset_8390;
ei_status.block_input = zorro8390_block_input;
ei_status.block_output = zorro8390_block_output;
ei_status.get_8390_hdr = zorro8390_get_8390_hdr;
ei_status.reg_offset = zorro8390_offsets;
dev->netdev_ops = &zorro8390_netdev_ops;
__NS8390_init(dev, 0);
ei_local->msg_enable = zorro8390_msg_enable;
err = register_netdev(dev);
if (err) {
free_irq(IRQ_AMIGA_PORTS, dev);
return err;
}
netdev_info(dev, "%s at 0x%08lx, Ethernet Address %pM\n",
name, board, dev->dev_addr);
return 0;
}
