/**
* Runs the motors with arcade steering.
*/
void OperatorControl(void)
{
HSLImage *Himage;
Threshold targetThreshold(247, 255, 60, 140, 10, 50);
BinaryImage *matchingPixels;
vector<ParticleAnalysisReport> *pReport;
//myRobot->SetSafetyEnabled(true);
Saftey->SetEnabled(false);
AxisCamera &mycam = AxisCamera::GetInstance("10.15.10.11");
mycam.WriteResolution(AxisCamera::kResolution_640x480);
mycam.WriteCompression(20);
mycam.WriteBrightness(25);
Wait(3.0);
dsLCD = DriverStationLCD::GetInstance();
dsLCD->Clear();
float X[2];
float Y[2];
float Z[2];
while(IsOperatorControl())
{
X[1] = Stick1->GetX();
X[2] = Stick2->GetX();
Y[1] = Stick1->GetY();
Y[2] = Stick2->GetY();
Z[1] = Stick1->GetZ();
Z[2] = Stick2->GetZ();
Jaguar1->Set(Y[1]);
Jaguar2->Set(Y[2]);
Wait(0.005);
if (mycam.IsFreshImage())
{
Himage = mycam.GetImage();
matchingPixels = Himage->ThresholdHSL(targetThreshold);
pReport = matchingPixels->GetOrderedParticleAnalysisReports();
for (unsigned int i = 0; i < pReport->size(); i++)
{
printf("Index: %d X Center: %d Y Center: %d \n", i, (*pReport)[i].center_mass_x, (*pReport)[i].center_mass_y);
}
delete Himage;
delete matchingPixels;
delete pReport;
}
}
//myRobot->ArcadeDrive(stick); // drive with arcade style (use right stick)
//Wait(0.005); // wait for a motor update time
}
void RobotDemo::interpolated_test_code()
{
float Test_Distance_Input = (((drive_stick_sec->GetZ() + 1) / 2.0) * 33.0)
- 1;
float Test_Distance_Output = lookup_distance_array(Test_Distance_Input);
printf("input:%f output:%f\n", Test_Distance_Input, Test_Distance_Output);
}
/**
* Get the Z value of the current joystick.
* This depends on the mapping of the joystick connected to the current port.
*
* @param port The USB port for this joystick.
*/
float GetZ(UINT32 port)
{
Joystick *stick = getJoystick(port);
if (stick == NULL)
return 0;
return stick->GetZ();
}
/**
* Runs the motors with Mecanum drive.
*/
void OperatorControl()
{
robotDrive.SetSafetyEnabled(false);
while (IsOperatorControl() && IsEnabled())
{
bool collisionDetected = false;
double curr_world_linear_accel_x = ahrs->GetWorldLinearAccelX();
double currentJerkX = curr_world_linear_accel_x - last_world_linear_accel_x;
last_world_linear_accel_x = curr_world_linear_accel_x;
double curr_world_linear_accel_y = ahrs->GetWorldLinearAccelY();
double currentJerkY = curr_world_linear_accel_y - last_world_linear_accel_y;
last_world_linear_accel_y = curr_world_linear_accel_y;
if ( ( fabs(currentJerkX) > COLLISION_THRESHOLD_DELTA_G ) ||
( fabs(currentJerkY) > COLLISION_THRESHOLD_DELTA_G) ) {
collisionDetected = true;
}
SmartDashboard::PutBoolean( "CollisionDetected", collisionDetected);
try {
/* Use the joystick X axis for lateral movement, */
/* Y axis for forward movement, and Z axis for rotation. */
/* Use navX MXP yaw angle to define Field-centric transform */
robotDrive.MecanumDrive_Cartesian(stick.GetX(), stick.GetY(),
stick.GetZ(),ahrs->GetAngle());
} catch (std::exception ex ) {
std::string err_string = "Error communicating with Drive System: ";
err_string += ex.what();
DriverStation::ReportError(err_string.c_str());
}
Wait(0.005); // wait 5ms to avoid hogging CPU cycles
}
}
/**
* @brief Sets a cached joystick value.
* @param joy_id Which joystick to set the cached value for.
* @param stick A Joystick object with the X, Y, and Z axes set, as well as each of the buttons.
*/
void Proxy::SetJoystick(int joy_id, Joystick & stick)
{
wpi_assert(joy_id < NUMBER_OF_JOYSTICKS+1 && joy_id >= 0);
char tmp[32];
sprintf(tmp, "Joy%d", joy_id);
string name = tmp;
if(!disableAxes[joy_id-1]) {
set(name + 'X', stick.GetX());
set(name + 'Y', stick.GetY());
set(name + 'Z', stick.GetZ());
set(name + 'R', stick.GetTwist());
set(name + 'T', stick.GetThrottle());
for(int AxisId=1; AxisId<=6; AxisId++) {
sprintf(tmp, "%sA%d", name.c_str(), AxisId);
set(tmp, stick.GetRawAxis(AxisId));
}
} else {
if(!stick.GetRawButton(disableAxes[joy_id-1])) {
set(name + 'X', stick.GetX());
set(name + 'Y', stick.GetY());
set(name + 'Z', stick.GetZ());
set(name + 'R', stick.GetTwist());
set(name + 'T', stick.GetThrottle());
for(int AxisId=1; AxisId<=6; AxisId++) {
sprintf(tmp, "%sA%d", name.c_str(), AxisId);
set(tmp, stick.GetRawAxis(AxisId));
}
}
}
if(!disableButtons[joy_id-1]) {
for(unsigned i=1;i<=NUMBER_OF_JOY_BUTTONS;i++) {
sprintf(tmp, "%sB%d", name.c_str(), i);
set(tmp,stick.GetRawButton(i));
}
set(name + "BT", stick.GetTrigger());
} else {
if(!stick.GetRawButton(disableButtons[joy_id-1])) {
for(unsigned i=1;i<=NUMBER_OF_JOY_BUTTONS;i++) {
sprintf(tmp, "%sB%d", name.c_str(), i);
set(tmp,stick.GetRawButton(i));
}
set(name + "BT", stick.GetTrigger());
}
}
}
void shootTask(){
while(true){
if(true){
if(!controller->GetRawButton(1)||controller->GetRawButton(3)){
if(controller->GetRawButton(5)||controller->GetRawButton(6)){
if(controller->GetRawButton(5)){
mySword->Intake(true);
}
else if(controller->GetRawButton(6)){
mySword->Release();
}
}
else{
mySword->Intake(false);
mySword->StopIntake();
mySword->StopIndexer();
}
}
else if(controller->GetRawButton(1)){
mySword->Shoot();
}
}
if(true){
if(controller->GetZ() > 0.1){
mySword->LiftIntake();
}
else if(controller->GetZ() < -0.1){
mySword->LowerIntake();
}
}
if(true){
if(controller->GetRawButton(3)){
mySword->Prime(true);
}else{
mySword->Prime(false);
}
}
Wait(0.005);
}
}
/**
* Drive based upon joystick inputs, and automatically control
* motors if the robot begins tipping.
*/
void OperatorControl()
{
robotDrive.SetSafetyEnabled(false);
while (IsOperatorControl() && IsEnabled()) {
double xAxisRate = stick.GetX();
double yAxisRate = stick.GetY();
double pitchAngleDegrees = ahrs->GetPitch();
double rollAngleDegrees = ahrs->GetRoll();
if ( !autoBalanceXMode &&
(fabs(pitchAngleDegrees) >=
fabs(kOffBalanceThresholdDegrees))) {
autoBalanceXMode = true;
}
else if ( autoBalanceXMode &&
(fabs(pitchAngleDegrees) <=
fabs(kOnBalanceThresholdDegrees))) {
autoBalanceXMode = false;
}
if ( !autoBalanceYMode &&
(fabs(pitchAngleDegrees) >=
fabs(kOffBalanceThresholdDegrees))) {
autoBalanceYMode = true;
}
else if ( autoBalanceYMode &&
(fabs(pitchAngleDegrees) <=
fabs(kOnBalanceThresholdDegrees))) {
autoBalanceYMode = false;
}
// Control drive system automatically,
// driving in reverse direction of pitch/roll angle,
// with a magnitude based upon the angle
if ( autoBalanceXMode ) {
double pitchAngleRadians = pitchAngleDegrees * (M_PI / 180.0);
xAxisRate = sin(pitchAngleRadians) * -1;
}
if ( autoBalanceYMode ) {
double rollAngleRadians = rollAngleDegrees * (M_PI / 180.0);
yAxisRate = sin(rollAngleRadians) * -1;
}
try {
// Use the joystick X axis for lateral movement, Y axis for forward movement, and Z axis for rotation.
robotDrive.MecanumDrive_Cartesian(xAxisRate, yAxisRate,stick.GetZ());
} catch (std::exception ex ) {
std::string err_string = "Drive system error: ";
err_string += ex.what();
DriverStation::ReportError(err_string.c_str());
}
Wait(0.005); // wait 5ms to avoid hogging CPU cycles
}
}
void RobotDemo::z_axis_control()
{
//shooter_motor_front->Set((-operator_stick->GetZ() + 1.0) / 2.0);//Shooter motors must always be set to positive values
//shooter_motor_back->Set((-operator_stick->GetZ() + 1.0) / 2.0);
if (!constant_desired_RPS)
{
desired_RPS_control = ((-operator_stick->GetZ() + 1) / 2) * 75;
RPS_control_code(desired_RPS_control);
}
}
/**
* Runs the motors with Mecanum drive.
*/
void OperatorControl()
{
robotDrive.SetSafetyEnabled(false);
while (IsOperatorControl() && IsEnabled())
{
// Use the joystick X axis for lateral movement, Y axis for forward movement, and Z axis for rotation.
// This sample does not use field-oriented drive, so the gyro input is set to zero.
robotDrive.MecanumDrive_Cartesian(stick.GetX(), stick.GetY(), stick.GetZ());
Wait(0.005); // wait 5ms to avoid hogging CPU cycles
}
}
/**
* @brief Sets a cached joystick value.
* @param joy_id Which joystick to set the cached value for.
* @param stick A Joystick object with the X, Y, and Z axes set, as well as each of the buttons.
*/
void Proxy166::SetJoystick(int joy_id, Joystick & stick)
{
wpi_assert(joy_id < NUMBER_OF_JOYSTICKS && joy_id >= 0);
//semTake(JoystickLocks[joy_id], WAIT_FOREVER);
Joysticks[joy_id].X = stick.GetX();
Joysticks[joy_id].Y = stick.GetY();
Joysticks[joy_id].Z = stick.GetZ();
Joysticks[joy_id].throttle = stick.GetThrottle();
for(unsigned i=0;i<NUMBER_OF_JOY_BUTTONS;i++) {
Joysticks[joy_id].button[i] = stick.GetRawButton(i);
}
//semGive(JoystickLocks[joy_id]);
}
/**
* Runs the motors with arcade steering.
*/
void OperatorControl(void)
{
log->Info("TELEOP START");
// myRobot.SetSafetyEnabled(true);
while (IsOperatorControl())
{
double distance = dist.GetVoltage() / (5.0 / 512.0);
SmartDashboard::Log(distance, "Rangefinder distance");
SmartDashboard::Log(dist.GetVoltage(), "Rangefinder voltage");
Sol1.Set(stick1.GetRawButton(1));
Sol2.Set(stick1.GetRawButton(2));
Sol3.Set(stick1.GetRawButton(3));
Sol4.Set(stick1.GetRawButton(4));
Sol5.Set(stick1.GetRawButton(5));
if (stick1.GetRawButton(6)) {
if (!lastButton) log->Shot(stick1.GetZ(), stick2.GetZ());
lastButton = true;
} else {
lastButton = false;
}
SmartDashboard::Log(((stick1.GetZ() + 1) / 2) * 2500, "Distance");
SmartDashboard::Log(((stick2.GetZ() + 1) / 2) * 5.0, "Compression");
SmartDashboard::Log(LookUp(stick1.GetZ() * 2500, /* stick2.GetZ() * 5.0 */ dist.GetVoltage()), "Shooter Speed");
// myRobot.ArcadeDrive(stick); // drive with arcade style (use right stick)
// lJagA.Set(stick1.GetY());
// lJagB.Set(stick1.GetY());
// rJagA.Set(stick2.GetY());
// rJagB.Set(stick2.GetY());
Wait(0.010); // wait for a motor update time
}
}
void RobotDemo::constant_RPS_code()
{
if (operator_stick->GetRawButton(front_position_button))
{
desired_RPS_control = front_position_RPS;
}
else
{
if (operator_stick->GetRawButton(back_position_button_1))
{
desired_RPS_control = back_position_RPS_1;
}
else if (operator_stick->GetRawButton(back_position_button_2))
{
desired_RPS_control = back_position_RPS_2;
}
else if (operator_stick->GetRawButton(back_position_button_3))
{
desired_RPS_control = back_position_RPS_3;
}
else if (operator_stick->GetRawButton(back_position_button_4))
{
desired_RPS_control = back_position_RPS_4;
}
else if (operator_stick->GetRawButton(back_position_button_5))
{
desired_RPS_control = back_position_RPS_5;
}
else
{
if (operator_stick->GetRawButton(dumper_button_A)
|| operator_stick->GetRawButton(dumper_button_B))
{
desired_RPS_control = dumper_RPS;
}
else
{
desired_RPS_control = ((-operator_stick->GetZ() + 1) / 2) * 75;
}
}
}
RPS_control_code(desired_RPS_control);
}
/**
* Runs the motors with Mecanum drive.
*/
void OperatorControl()
{
robotDrive.SetSafetyEnabled(false);
while (IsOperatorControl() && IsEnabled())
{
bool motionDetected = ahrs->IsMoving();
SmartDashboard::PutBoolean("MotionDetected", motionDetected);
try {
/* Use the joystick X axis for lateral movement, */
/* Y axis for forward movement, and Z axis for rotation. */
/* Use navX MXP yaw angle to define Field-centric transform */
robotDrive.MecanumDrive_Cartesian(stick.GetX(), stick.GetY(),
stick.GetZ(),ahrs->GetAngle());
} catch (std::exception ex ) {
std::string err_string = "Error communicating with Drive System: ";
err_string += ex.what();
DriverStation::ReportError(err_string.c_str());
}
Wait(0.005); // wait 5ms to avoid hogging CPU cycles
}
}
void TeleopPeriodic()
{
if(stick.GetRawButton(3))
{
sm2kl.Set(1.0);
sm2kr.Set(1.0);
}
if(rSwitch.Get())
{
sm2kr.Set(0.0);
sm2kl.Set(0.0);
SmartDashboard::PutNumber("Tests",675);
}
if(stick.GetRawButton(5))
{
sm2kl.Set(-1.0);
sm2kr.Set(-1.0);
SmartDashboard::PutNumber("Tests",675);
}
if((lEnc.GetDistance() > 1080)||(rEnc.GetDistance() > 1080))
{
sm2kl.Set(0.0);
sm2kr.Set(0.0);
}
if(stick.GetRawButton(10))
{
actintake.Set(1.0);
}
else if(stick.GetRawButton(9))
{
actintake.Set(-1.0);
}
else
{
actintake.Set(0.0);
}
xvalue = -stick.GetZ()*.5;
yvalue = -stick.GetY();
if(stick.GetRawButton(7)&&!toggle)
{
latch=!latch;
toggle=true;
}
if(!stick.GetRawButton(7)&&toggle)
{
toggle=false;
}
if(latch)
{
yvalue=-yvalue;
}
if(stick.GetRawButton(1))
{
launcher.Set(1.0);
}
if(stick.GetRawButton(11))
{
intake.Set(1.0);
}
myRobot.ArcadeDrive(yvalue,xvalue);
SmartDashboard::PutNumber("rSwitch",rSwitch.Get());
SmartDashboard::PutBoolean("latch",latch);
SmartDashboard::PutNumber("Button",stick.GetRawButton(5));
//myRobot.ArcadeDrive(stick); // drive with arcade style (use right stick)
}
float ScaleZ( Joystick& stick) {
// CONSTANT^-1 is step value (now 1/500)
return floorf( 500.f * ( 1.f - stick.GetZ() ) / 2.f ) / 500.f;
}
/**
* Runs the motors with arcade steering.
*/
void OperatorControl(void)
{
myRobot->SetSafetyEnabled(true);
while (IsOperatorControl())
{
bool setLimit;
double cimValue1= -scaleThrottle(-(stick->GetZ())); //Set desired speed from the Throttle, assuming from -1 to 1, also invert the cim, since we want it to rotate coutnerclockwise/clockwise
double cimValue2= scaleThrottle(-(stick->GetZ())); //Set desired speed from the Throttle, assuming from -1 to 1
//For shooter
/*if (stick.GetRawButton(1) == true) {
//back of the robot is moved forward by pushing forward on the joystick
myRobot.ArcadeDrive((stick.GetY()),
(stick.GetX()), false); // inverted drive control
} else {
//front of the robot is moved forward by pushing forward on the joystick
myRobot.ArcadeDrive(-(stick.GetY()),
(stick.GetX()), false); // normal drive control
}
*/
//For manual button speed control, this sets the speed
if (stick->GetRawButton(4) == true) {
cim1->Set(cimValue1); //use the value from the throttle to set cim speed
cim2->Set(cimValue2);//Get speed from throttle, and then scale it
setLimit = true;
//Open Ball Stopper
}
else {
cim1->Set(0.0);
cim2->Set(0.0);
setLimit = false;
//Close Ball Stopper
}
//For precisebelt pickup
if (stick->GetRawButton(1) == true) {
//back of the robot is moved forward by pushing forward on the joystick
if (setLimit == true) {
JagBelt->ArcadeDrive(0.1,
(stick->GetX()), false); // inverted drive control
} else {
JagBelt->ArcadeDrive((stick->GetY()),
(stick->GetX()), false); // inverted drive control
}
} else {
//front of the robot is moved forward by pushing forward on the joystick
if (setLimit == true) {
JagBelt->ArcadeDrive(-0.1,
(stick->GetX()), false); // inverted drive control
} else {
JagBelt->ArcadeDrive(-(stick->GetY()),
(stick->GetX()), false); // inverted drive control
}
}
//For normal belt pickup
/*if (stick->GetRawButton(6) == true) {
JagBelt->Drive(1.0, 0); //opens gripper
} else {
JagBelt->Drive(0.0, 0); //closes gripper
}
*/
//For drive
if (rightstick->GetRawButton(1) == true) {
//back of the robot is moved forward by pushing forward on the joystick
if (rightstick->GetRawButton(10) == true) {
precisionMode= true;
}
else {
precisionMode= false;
}
myRobot->ArcadeDrive((rightstick->GetY()), (rightstick->GetX()), precisionMode); // inverted drive control
} else
{
if (rightstick->GetRawButton(10) == true) {
precisionMode= true;
}
else {
precisionMode= false;
}
//front of the robot is moved forward by pushing forward on the joystick
myRobot->ArcadeDrive(-(rightstick->GetY()), (rightstick->GetX()), precisionMode); // normal drive control
}
/*if (stick->GetRawButton(8) == true) {
cim1->Set(-0.37); //run cim 1 at 50% speed counterclockwise??
cim2->Set(0.37); // run cim at 50% speed clockwise
check = true; //indicate if motors are running
} else if (check == true){ // if motors are running a
Wait(2.0);
belt->Set(1); // run the belt
Wait(2.0); // one sec delay
belt->Set(0.0); // turn belt off
check = false; // put new check
}
else if (check == false){ //if false
// 2 sec delay to wait for the first ball to shoot
cim1->Set(0.0); //stop cims
cim2->Set(0.0);
}
else { // Stop everything
cim1->Set(0.0); //stop cims
cim2->Set(0.0);
belt->Set(0.0);
}
*/
//Code for using window motor
if (rightstick->GetRawButton(4)) {
window->Set(Relay::kOn);
window->Set(Relay::kForward); // tell window motor to go forward
} else if (rightstick->GetRawButton(5) == true){
window->Set(Relay::kOn);
window->Set(Relay::kReverse); //tell window motor to go backward
}
else {
//Wait(1.0);
window->Set(Relay::kOff); //turn it off, if the relays aint being used
}
//Code for Banebot Motor for stopping ballz
if (stick->GetRawButton(2) == true) { // press button TWO to close
pickStop->Set(-0.5); //closes ball stopper
Wait(1);
pickStop->Set(0.0);
} else if (stick->GetRawButton(3) == true){ //press button three to open
pickStop->Set(0.5); //opens ball stopper
Wait(1.2); // too slow, so needs more time
pickStop->Set(0.0);
}
else if (stick->GetRawButton(5)== true){ //press 5 to stop imediately, useful for adjusting angles...
//Wait(1.0);
pickStop->Set(0.0);
}
//Code for ... servoooo
if (stick->GetRawButton(10) == true) { //press 10 on the left stick...
bar->SetAngle(60); // set the angles to 60...clockwise?
bar2->SetAngle(60);
} else if (stick->GetRawButton(11) == true) // press 11 on the left stick
{
bar->SetAngle(-60); //set the angles to -60...counterclockwise?
bar2->SetAngle(-60);
}
// Initialize functions...
// RelayServo();
//PreciseBelt();
//UltrasonicRange();
// Accelerometer();
//dash->GetPacketNumber();
// send data back to dashboard
dash->GetPacketNumber(); //not sure why this is here 0_0
//int limitValue= limitSwitch->Get() ? 1 : 0; // retrieve 1 and 0 only.../ look for 0 and 1
float servoAngle = bar->GetAngle();
//dsLCD->Printf(DriverStationLCD::kUser_Line1, 1, "Limit State: %d", limitValue); //send data back to driver station...
// dsLCD->Printf(DriverStationLCD::kUser_Line2, 2, "Servo Angle: %f", servoAngle); //send data back to driver station...
float gyroVal = gyro -> GetVoltage();//Gets voltage from gyro
float ultraVal = rangeFinder -> GetVoltage(); //Get voltage from ultrasonic sensor
float tempVal = Temperature -> GetVoltage();//Gets temperature
//Do the math to convert data received from the ultrasonic volts->miliVolts->milivolts per inch->inches
float Vm = (ultraVal*1000);
float Ri = (Vm/9.765625);
// Print data back to dashboard
dsLCD->Printf(DriverStationLCD::kUser_Line1, 1, "Ultrasonic Range: %f",Ri);
dsLCD->Printf(DriverStationLCD::kUser_Line2, 1, "Gyro: %f", gyroVal);
dsLCD->Printf(DriverStationLCD::kUser_Line3, 1, "Temperature: %f", tempVal);
dsLCD->Printf(DriverStationLCD::kUser_Line4, 1, "Cim1 Speed: %f%%", (cimValue1*100)); //display speed that the mototrs are reunning at different percentages...
dsLCD->Printf(DriverStationLCD::kUser_Line5, 1, "Cim2 Speed: %f%%", (cimValue2*100));
//Update dashboard
dsLCD->UpdateLCD();
}
}
/**
* Runs the motors with Mecanum drive.
*/
void OperatorControl()//teleop code
{
robotDrive.SetSafetyEnabled(false);
gyro.Reset();
grabEncoder.Reset();
timer.Start();
timer.Reset();
double liftHeight = 0; //variable for lifting thread
int liftHeightBoxes = 0; //another variable for lifting thread
int liftStep = 0; //height of step in inches
int liftRamp = 0; //height of ramp in inches
double grabPower;
bool backOut;
uint8_t toSend[10];//array of bytes to send over I2C
uint8_t toReceive[10];//array of bytes to receive over I2C
uint8_t numToSend = 1;//number of bytes to send
uint8_t numToReceive = 0;//number of bytes to receive
toSend[0] = 1;//set the byte to send to 1
i2c.Transaction(toSend, 1, toReceive, 0);//send over I2C
bool isGrabbing = false;//whether or not grabbing thread is running
bool isLifting = false;//whether or not lifting thread is running
bool isBraking = false;//whether or not braking thread is running
float driveX = 0;
float driveY = 0;
float driveZ = 0;
float driveGyro = 0;
bool liftLastState = false;
bool liftState = false; //button pressed
double liftLastTime = 0;
double liftTime = 0;
bool liftRan = true;
Timer switchTimer;
Timer grabTimer;
switchTimer.Start();
grabTimer.Start();
while (IsOperatorControl() && IsEnabled())
{
// Use the joystick X axis for lateral movement, Y axis for forward movement, and Z axis for rotation.
// This sample does not use field-oriented drive, so the gyro input is set to zero.
toSend[0] = 1;
numToSend = 1;
driveX = driveStick.GetRawAxis(Constants::driveXAxis);//starts driving code
driveY = driveStick.GetRawAxis(Constants::driveYAxis);
driveZ = driveStick.GetRawAxis(Constants::driveZAxis);
driveGyro = gyro.GetAngle() + Constants::driveGyroTeleopOffset;
if (driveStick.GetRawButton(Constants::driveOneAxisButton)) {//if X is greater than Y and Z, then it will only go in the direction of X
toSend[0] = 6;
numToSend = 1;
if (fabs(driveX) > fabs(driveY) && fabs(driveX) > fabs(driveZ)) {
driveY = 0;
driveZ = 0;
}
else if (fabs(driveY) > fabs(driveX) && fabs(driveY) > fabs(driveZ)) {//if Y is greater than X and Z, then it will only go in the direction of Y
driveX = 0;
driveZ = 0;
}
else {//if Z is greater than X and Y, then it will only go in the direction of Z
driveX = 0;
driveY = 0;
}
}
if (driveStick.GetRawButton(Constants::driveXYButton)) {//Z lock; only lets X an Y function
toSend[0] = 7;
driveZ = 0;//Stops Z while Z lock is pressed
}
if (!driveStick.GetRawButton(Constants::driveFieldLockButton)) {//robot moves based on the orientation of the field
driveGyro = 0;//gyro stops while field lock is enabled
}
driveX = Constants::scaleJoysticks(driveX, Constants::driveXDeadZone, Constants::driveXMax * (.5 - (driveStick.GetRawAxis(Constants::driveThrottleAxis) / 2)), Constants::driveXDegree);
driveY = Constants::scaleJoysticks(driveY, Constants::driveYDeadZone, Constants::driveYMax * (.5 - (driveStick.GetRawAxis(Constants::driveThrottleAxis) / 2)), Constants::driveYDegree);
driveZ = Constants::scaleJoysticks(driveZ, Constants::driveZDeadZone, Constants::driveZMax * (.5 - (driveStick.GetRawAxis(Constants::driveThrottleAxis) / 2)), Constants::driveZDegree);
robotDrive.MecanumDrive_Cartesian(driveX, driveY, driveZ, driveGyro);//makes the robot drive
if (pdp.GetCurrent(Constants::grabPdpChannel) < Constants::grabManualCurrent) {
pickup.setGrabber(Constants::scaleJoysticks(grabStick.GetX(), Constants::grabDeadZone, Constants::grabMax, Constants::grabDegree)); //defines the grabber
if(grabTimer.Get() < 1) {
toSend[0] = 6;
}
}
else {
pickup.setGrabber(0);
grabTimer.Reset();
toSend[0] = 6;
}
if (Constants::grabLiftInverted) {
pickup.setLifter(-Constants::scaleJoysticks(grabStick.GetY(), Constants::liftDeadZone, Constants::liftMax, Constants::liftDegree)); //defines the lifter
}
else {
pickup.setLifter(Constants::scaleJoysticks(grabStick.GetY(), Constants::liftDeadZone, Constants::liftMax, Constants::liftDegree)); //defines the lifter
}
SmartDashboard::PutNumber("Lift Power", Constants::scaleJoysticks(grabStick.GetY(), Constants::liftDeadZone, Constants::liftMax, Constants::liftDegree));
SmartDashboard::PutBoolean("Is Lifting", isLifting);
if (Constants::scaleJoysticks(grabStick.GetY(), Constants::liftDeadZone, Constants::liftMax, Constants::liftDegree) != 0 || isLifting) { //if the robot is lifting
isBraking = false; //stop braking thread
SmartDashboard::PutBoolean("Braking", false);
}
else if(!isBraking) {
isBraking = true; //run braking thread
pickup.lifterBrake(isBraking);//brake the pickup
}
if (grabStick.GetRawButton(Constants::liftFloorButton)) {
liftHeight = 0;
pickup.lifterPosition(liftHeight, isLifting, grabStick);//start lifting thread
liftRan = true;
}
liftTime = timer.Get();
liftState = grabStick.GetRawButton(Constants::liftButton);
if (liftState) { //if button is pressed
if (!liftLastState) {
if (liftTime - liftLastTime < Constants::liftMaxTime) {
if (liftHeightBoxes < Constants::liftMaxHeightBoxes) {
liftHeightBoxes++; //adds 1 to liftHeightBoxes
}
}
else {
liftHeightBoxes = 1;
liftRamp = 0;
liftStep = 0;
}
}
liftLastTime = liftTime;
liftLastState = true;
liftRan = false;
}
else if (grabStick.GetRawButton(Constants::liftRampButton)) {
if (liftTime - liftLastTime > Constants::liftMaxTime) {
liftHeight = 0;
liftStep = 0;
}
liftRamp = 1; //prepares to go up ramp
liftLastTime = liftTime;
liftRan = false;
}
else if (grabStick.GetRawButton(Constants::liftStepButton)) {
if (liftTime - liftLastTime > Constants::liftMaxTime) {
liftHeight = 0;
liftRamp = 0;
}
liftStep = 1; //prepares robot for step
liftLastTime = liftTime;
liftRan = false;
}
else {
if (liftTime - liftLastTime > Constants::liftMaxTime && !liftRan) {
liftHeight = liftHeightBoxes * Constants::liftBoxHeight + liftRamp * Constants::liftRampHeight + liftStep * Constants::liftStepHeight; //sets liftHeight
if (liftHeightBoxes > 0) {
liftHeight -= Constants::liftBoxLip;
}
pickup.lifterPosition(liftHeight, isLifting, grabStick);//start lifting thread
liftRan = true;
}
liftLastState = false;
}
if (grabStick.GetRawButton(Constants::grabToteButton)) {//if grab button is pressed
grabPower = Constants::grabToteCurrent;
backOut = true;
if (!isGrabbing) {
pickup.grabberGrab(isGrabbing, grabPower, backOut, grabStick);//start grabber thread
}
}
else if (grabStick.GetRawButton(Constants::grabBinButton)) {//if grab button is pressed
grabPower = Constants::grabBinCurrent;
backOut = false;
if (!isGrabbing) {
pickup.grabberGrab(isGrabbing, grabPower, backOut, grabStick);//start grabber thread
}
}
else if (grabStick.GetRawButton(Constants::grabChuteButton)) {//if grab button is presset
SmartDashboard::PutBoolean("Breakpoint -2", false);
SmartDashboard::PutBoolean("Breakpoint -1", false);
SmartDashboard::PutBoolean("Breakpoint 0", false);
SmartDashboard::PutBoolean("Breakpoint 1", false);
SmartDashboard::PutBoolean("Breakpoint 2", false);
SmartDashboard::PutBoolean("Breakpoint 3", false);
SmartDashboard::PutBoolean("Breakpoint 4", false);
//Wait(.5);
if (!isGrabbing) {
//pickup.grabberChute(isGrabbing, grabStick);//start grabber thread
}
}
//determines what the LED's look like based on what the Robot is doing
if (isGrabbing) {
toSend[0] = 5;
numToSend = 1;
}
if (isLifting) {//if the grabbing thread is running
if (Constants::encoderToDistance(liftEncoder.Get(),Constants::liftEncoderTicks, Constants::liftEncoderBase, Constants::liftEncoderRadius) < liftHeight) {
toSend[0] = 3;
}
else {
toSend[0] = 4;
}
numToSend = 1;//sends 1 byte to I2C
}
if(!grabOuterLimit.Get()) { //tells if outer limit is hit with lights
if(switchTimer.Get() < 1) {
toSend[0] = 6;
}
}
else {
switchTimer.Reset();
}
if (driveStick.GetRawButton(Constants::sneakyMoveButton)) {
toSend[0] = 0;
numToSend = 1;
}
float distance = prox.GetVoltage() * Constants::ultrasonicVoltageToInches / 12; // distance from ultrasonic sensor
float rotations = (float) liftEncoder.Get(); // rotations on encoder
SmartDashboard::PutNumber("Distance", distance); // write stuff to smart dash
SmartDashboard::PutNumber("Current", pdp.GetCurrent(Constants::grabPdpChannel));
SmartDashboard::PutNumber("LED Current", pdp.GetCurrent(Constants::ledPdpChannel));
SmartDashboard::PutNumber("Lift Encoder", rotations);
SmartDashboard::PutNumber("Lift Height", liftHeight);
SmartDashboard::PutNumber("Grab Encoder", grabEncoder.Get());
SmartDashboard::PutBoolean("Grab Inner", grabInnerLimit.Get());
SmartDashboard::PutBoolean("Grab Outer", grabOuterLimit.Get());
SmartDashboard::PutNumber("Drive Front Left Current", pdp.GetCurrent(Constants::driveFrontLeftPin));
SmartDashboard::PutNumber("Drive Front Right Current", pdp.GetCurrent(Constants::driveFrontRightPin));
SmartDashboard::PutNumber("Drive Rear Left Current", pdp.GetCurrent(Constants::driveRearLeftPin));
SmartDashboard::PutNumber("Drive Rear Right Current", pdp.GetCurrent(Constants::driveRearRightPin));
SmartDashboard::PutNumber("Throttle", grabStick.GetZ());
i2c.Transaction(toSend, 1, toReceive, 0);//send and receive information from arduino over I2C
Wait(0.005); // wait 5ms to avoid hogging CPU cycles
} //end of teleop
isBraking = false;
toSend[0] = 0;
i2c.Transaction(toSend, numToSend, toReceive, numToReceive);
}
void Autonomous()
{
Timer timer;
float power = 0;
bool isLifting = false;
bool isGrabbing = false;
double liftHeight = Constants::liftBoxHeight-Constants::liftBoxLip;
double grabPower = Constants::grabAutoCurrent;
bool backOut;
uint8_t toSend[1];//array of bytes to send over I2C
uint8_t toReceive[0];//array of bytes to receive over I2C
uint8_t numToSend = 1;//number of bytes to send
uint8_t numToReceive = 0;//number of bytes to receive
toSend[0] = 2;//set the byte to send to 1
i2c.Transaction(toSend, numToSend, toReceive, numToReceive);//send over I2C
bool isSettingUp = true;
//pickup.setGrabber(-1); //open grabber all the way
pickup.setLifter(0.8);
while (isSettingUp && IsEnabled() && IsAutonomous()) {
isSettingUp = false;
/*if (grabOuterLimit.Get() == false) {
pickup.setGrabber(0); //open until limit
}
else {
isSettingUp = true;
}*/
if (liftLowerLimit.Get()) {
pickup.setLifter(0); //down till bottom
}
else {
isSettingUp = true;
}
}
gyro.Reset();
liftEncoder.Reset();
grabEncoder.Reset();
if (grabStick.GetZ() > .8) {
timer.Reset();
timer.Start();
while (timer.Get() < 1) {
robotDrive.MecanumDrive_Cartesian(0, power, 0, gyro.GetAngle()); // drive back
if(power>-.4){
power-=0.005;
Wait(.005);
}
}
robotDrive.MecanumDrive_Cartesian(0, 0, 0, gyro.GetAngle()); // STOP!!!
timer.Stop();
timer.Reset();
Wait(1);
}
power = 0;
while (isLifting && IsEnabled() && IsAutonomous()) {
Wait(.005);
}
backOut = Constants::autoBackOut;
pickup.grabberGrab(isGrabbing, grabPower, backOut, grabStick);
Wait(.005);
while (isGrabbing && IsEnabled() && IsAutonomous()) {
Wait(.005);
}
liftHeight = 3*Constants::liftBoxHeight;
Wait(.005);
pickup.lifterPosition(liftHeight, isLifting, grabStick);
Wait(.005);
while (isLifting && IsEnabled() && IsAutonomous()) {
Wait(.005);
}
while(prox.GetVoltage() * Constants::ultrasonicVoltageToInches / 12 < 2 && IsEnabled() && IsAutonomous()); // while the nearest object is closer than 2 feet
timer.Start();
while(prox.GetVoltage() * Constants::ultrasonicVoltageToInches < Constants::autoBackupDistance && timer.Get() < Constants::autoMaxDriveTime && IsEnabled() && IsAutonomous()) { // while the nearest object is further than 12 feet
if (power < .45) { //ramp up the power slowly
power += .00375;
}
robotDrive.MecanumDrive_Cartesian(0, power, 0, gyro.GetAngle()); // drive back
float distance = prox.GetVoltage() * Constants::ultrasonicVoltageToInches / 12; // distance from ultrasonic sensor
SmartDashboard::PutNumber("Distance", distance); // write stuff to smart dash
SmartDashboard::PutNumber("Drive Front Left Current", pdp.GetCurrent(Constants::driveFrontLeftPin));
SmartDashboard::PutNumber("Drive Front Right Current", pdp.GetCurrent(Constants::driveFrontRightPin));
SmartDashboard::PutNumber("Drive Rear Left Current", pdp.GetCurrent(Constants::driveRearLeftPin));
SmartDashboard::PutNumber("Drive Rear Right Current", pdp.GetCurrent(Constants::driveRearRightPin));
SmartDashboard::PutNumber("Gyro Angle", gyro.GetAngle());
SmartDashboard::PutNumber("Distance (in)", prox.GetVoltage() * Constants:: ultrasonicVoltageToInches);
Wait(.005);
}
timer.Reset();
while(timer.Get() < Constants::autoBrakeTime && IsEnabled() && IsAutonomous()) { // while the nearest object is further than 12 feet
robotDrive.MecanumDrive_Cartesian(0,Constants::autoBrakePower,0); ///Brake
}
float turn = 0;
while (fabs(turn) < 85 && IsEnabled() && IsAutonomous()) { //turn 90(ish) degrees
robotDrive.MecanumDrive_Cartesian(0,0,.1);
turn = gyro.GetAngle();
if (turn > 180) {
turn -= 360;
}
}
robotDrive.MecanumDrive_Cartesian(0,0,0); ///STOP!!!
timer.Stop();
toSend[0] = 8;
i2c.Transaction(toSend, numToSend, toReceive, numToReceive);
while(IsAutonomous() && IsEnabled());
toSend[0] = 0;
i2c.Transaction(toSend, numToSend, toReceive, numToReceive);
}
void OperatorControl(void)
{
JankyTurret turret(7,11,10);
JankyTargeting targ(&turret);
JankyShooter shoot(SHOOTER_JAGUAR_CHANNEL,SHOOTER_ENCODER_A,SHOOTER_ENCODER_B);
int rpmForShooter=0;
while (IsOperatorControl())
{
//GetImage()
//hsl.Save
// myRobot.ArcadeDrive(stick);
shoot.GetCurrentRPM();
if (button.Get()==true)
{
LEDRelay.Set(Relay::kForward);
if (button_H.Get()==true)
{
targ.SetLMHTarget(BOGEY_H);
SmartDashboard::PutString("Targeting","High Button Pressed");
}
if (button_M.Get()==true)
{
targ.SetLMHTarget(BOGEY_M);
SmartDashboard::PutString("Targeting","Medium Button Pressed");
}
if (button_L.Get()==true)
{
targ.SetLMHTarget(BOGEY_L);
SmartDashboard::PutString("Targeting","Low Button Pressed");
}
if (button_H.Get()==true || button_M.Get()==true || button_L.Get()==true)
{
if (targ.ProcessOneImage())
{
targ.ChooseBogey();
targ.MoveTurret();
rpmForShooter = targ.GetCalculatedRPM();
shoot.setTargetRPM(rpmForShooter);
targ.InteractivePIDSetup();
}
}
targ.StopPID();
shoot.setTargetRPM(0);
}
else
{
float lazysusan =stick.GetZ();
turret.Set(lazysusan);
LEDRelay.Set(Relay::kOff);
// Set shooter speed to zero.
}
// float desired=abs(stick.GetY() *1000) + 100;
// smarty->PutInt("Desired RPM1", (int)desired);
// shoot.setTargetRPM((int)desired);
Wait(0.05);
}
// After teleop runs, save preferences again.
Preferences::GetInstance()->Save();
}
/****************************************
* Runs the motors with arcade steering.*
****************************************/
void OperatorControl(void)
{
//TODO put in servo for lower camera--look in WPI to set
// Watchdog baddog;
// baddog.Feed();
myRobot.SetSafetyEnabled(true);
//SL Earth.Start(); // turns on Earth
// SmartDashboard *smarty = SmartDashboard::GetInstance();
//DriverStationLCD *dslcd = DriverStationLCD::GetInstance(); // don't press SHIFT 5 times; this line starts up driver station messages (in theory)
//char debugout [100];
compressor.Start();
gyro.Reset(); // resets gyro angle
int rpmForShooter;
while (IsOperatorControl()) // while is the while loop for stuff; this while loop is for "while it is in Teleop"
{
// baddog.Feed();
//myRobot.SetSafetyEnabled(true);
//myRobot.SetExpiration(0.1);
float leftYaxis = driver.GetY();
float rightYaxis = driver.GetTwist();//RawAxis(5);
myRobot.TankDrive(leftYaxis,rightYaxis); // drive with arcade style (use right stick)for joystick 1
float random = gamecomponent.GetY();
float lazysusan = gamecomponent.GetZ();
//bool elevator = Frodo.Get();
float angle = gyro.GetAngle();
bool balance = Smeagol.Get();
SmartDashboard::PutNumber("Gyro Value",angle);
int NumFail = -1;
//bool light = Pippin.Get();
//SL float speed = Earth.GetRate();
//float number = shooter.Get();
//bool highspeed = button1.Get()
//bool mediumspeed = button2.Get();
//bool slowspeed = button3.Get();
bool finder = autotarget.Get();
//bool targetandspin = autodistanceandspin.Get();
SmartDashboard::PutString("Targeting Activation","");
//dslcd->Clear();
//sprintf(debugout,"Number=%f",angle);
//dslcd->Printf(DriverStationLCD::kUser_Line2,2,debugout);
//SL sprintf(debugout,"Number=%f",speed);
//SL dslcd->Printf(DriverStationLCD::kUser_Line4,4,debugout);
//sprintf(debugout,"Number=%f",number);
//dslcd->Printf(DriverStationLCD::kUser_Line1,1,debugout);
//sprintf(debugout,"Finder=%u",finder);
//dslcd->Printf(DriverStationLCD::kUser_Line5,5,debugout);
//dslcd->UpdateLCD(); // update the Driver Station with the information in the code
// sprintf(debugout,"Number=%u",maxi);
// dslcd->Printf(DriverstationLCD::kUser_Line6,5,debugout)
bool basketballpusher = julesverne.Get();
bool bridgetipper = joystickbutton.Get();
if (bridgetipper) // if joystick button 7 is pressed (is true)
{
solenoid.Set(true); // then the first solenoid is on
}
else
{
//Wait(0.5); // and then the first solenoid waits for 0.5 seconds
solenoid.Set(false); //and then the first solenoid turns off
}
if (basketballpusher) // if joystick button 6 is pressed (is true)
{
shepard.Set(true); // then shepard is on the run
//Wait(0.5); // and shepard waits for 0.5 seconds
}
else
{
shepard.Set(false); // and then shepard turns off
} //10.19.67.9 IP address of computer;255.0.0.0 subnet mask ALL FOR WIRELESS CONNECTION #2
//}
//cheetah.Set(0.3*lazysusan);
// smarty->PutDouble("pre-elevator",lynx.Get());
lynx.Set(random);
// smarty->PutDouble("elevator",lynx.Get());
// smarty->PutDouble("joystick elevator",random);
if (balance) // this is the start of the balancing code
{
angle = gyro.GetAngle();
myRobot.Drive(-0.03*angle, 0.0);
Wait(0.005);
}
/*if (light) //button 5 turns light on oand off on game controller
flashring.Set(Relay::kForward);
else
flashring.Set(Relay::kOff);
*/
if (finder)
{
flashring.Set(Relay::kForward);
if (button_H.Get()==true)
{
targeting.SetLMHTarget(BOGEY_H);
SmartDashboard::PutString("Targeting","High Button Pressed");
}
if (button_M.Get()==true)
{
targeting.SetLMHTarget(BOGEY_M);
SmartDashboard::PutString("Targeting","Medium Button Pressed");
}
if (button_L.Get()==true)
{
targeting.SetLMHTarget(BOGEY_L);
SmartDashboard::PutString("Targeting","Low Button Pressed");
}
if (button_H.Get()==true || button_M.Get()==true || button_L.Get()==true)
{
if (targeting.ProcessOneImage())
{
NumFail = 0;
SmartDashboard::PutString("Targeting Activation","YES");
targeting.ChooseBogey();
targeting.MoveTurret();
#ifdef USE_HARDWIRED_RPM
shooter.setTargetRPM(HARDWIRED_RPM);
#else
rpmForShooter = targeting.GetCalculatedRPM();
shooter.setTargetRPM(rpmForShooter);
#endif
targeting.InteractivePIDSetup();
}
else
{
NumFail++;
if (NumFail > 10)
targeting.StopPID();
}
SmartDashboard::PutNumber("Numfail", NumFail);
shooter.setTargetRPM(rpmForShooter);
}
else
{
SmartDashboard::PutString("Targeting Activation","NO");
shooter.setTargetRPM(0);
targeting.StopPID();
}
}
else
{
flashring.Set(Relay::kOff);
targeting.StopPID();
turret.Set(lazysusan); // the lazy susan would turn right & left based on how far the person moves the right joystick#2 side to side
//targeting.StopPID();
//if (elevator) //shooter would move at full speed if button is pressed
//TODO Change RPM values
//TODO Disable calculation of RPM values
SmartDashboard::PutNumber("CurrentRPM",shooter.GetCurrentRPM());
if (button_H.Get() == true)
shooter.setTargetRPM((int)2100);
//From front of free throw line, should hit the backboard and go in
//used to be 2700 RPMs
else if (button_M.Get() == true)
shooter.setTargetRPM((int)1900);
//From front of free throw line, should go in the net--can shoot the next ball on the overshoot?
//Used to be 2250 RPMs
else if (button_L.Get() == true)
shooter.setTargetRPM((int)1350);
//From fender, should hit the backboard
//Used to be 2000 RPMs
//shooter.Set(0.5);
else
shooter.setTargetRPM(0);
// else if (mediumspeed)
//shooter.setTargetRPM((int)0);
//else if (slowspeed)
//shooter.setTargetRPM((int)0);
/*if (targetandspin) //code for autotargeting and speed will go here
{
shooter.setTargetRPM((int)1800);
}
else
{*/
//}
myRobot.TankDrive(leftYaxis,rightYaxis);
}
//Wait(0.005);
}
}
void TeleopPeriodic() {
if(tick==10) if (ds->IsSysBrownedOut()) {
ds->ReportError("[ERROR] BROWNOUT DETECTED!!");
}
if(tick == 15) if (!ds->IsNewControlData()) {
ds->ReportError(
"[ERROR] NO DATA FROM DRIVER STATION IN THIS TICK!");
}
if(tick==20) if (!ds->IsDSAttached()) {
ds->ReportError("[ERROR] DRIVER STATION NOT DETECTED!");
}
if (stick.GetRawButton(10))
zeroSanics();
if (stick.GetRawButton(8)) {
leftIRZero = 0;
rightIRZero = 0;
}
tick++;
if (liftStick.GetRawButton(2)) {
double canScale = liftStick.GetRawAxis(2);
canScale += 1;
canScale = 2 - canScale;
canScale /= 2;
canGrabber.SetSpeed(canScale);
} else if (liftStick.GetRawButton(3)) {
double canScale = liftStick.GetRawAxis(2);
canScale += 1;
canScale = 2 - canScale;
canScale /= 2;
canGrabber.SetSpeed(-canScale);
} else
canGrabber.SetSpeed(0);
double speed;
//Calculate scalar to use for POV/Adjusted drive
double scale = stick.GetRawAxis(3);
scale += 1;
scale = 2 - scale;
scale /= 2;
//Use pov/hat switch for movement if enabled
if (stick.GetRawButton(1) && stick.GetRawButton(2)) {
AutomaticLineup();
} else if (stick.GetRawButton(1)) {
double leftVolts = leftIR.GetAverageVoltage() - leftIRZero;
double rightVolts = rightIR.GetAverageVoltage() - leftIRZero;
if (rightVolts + VOLTAGE_TOLERANCE > leftVolts
&& rightVolts - VOLTAGE_TOLERANCE < leftVolts) {
robotDrive.MecanumDrive_Cartesian(0, 0, 0);
} else if (rightVolts > leftVolts)
robotDrive.MecanumDrive_Cartesian(0, 0, 0.2);
else if (leftVolts > rightVolts)
robotDrive.MecanumDrive_Cartesian(0, 0, -0.2);
} else if (stick.GetRawButton(6)) {
//Rotate
robotDrive.MecanumDrive_Polar(0, 0, scale);
} else if (stick.GetRawButton(5)) {
//Rotate
robotDrive.MecanumDrive_Polar(0, 0, -scale);
} else if (stick.GetPOV(0) != -1) {
//If POV moved, move polar (getPOV returns an angle in degrees)
robotDrive.MecanumDrive_Polar(scale, -stick.GetPOV(0), 0);
} else if (stick.GetRawButton(2)) {
//Drive with scalar
robotDrive.MecanumDrive_Cartesian(-stick.GetRawAxis(0) * scale,
stick.GetRawAxis(1) * scale, stick.GetRawAxis(2) * scale);
} else {
//Drive normally
robotDrive.MecanumDrive_Cartesian(-stick.GetX(), stick.GetY(),
stick.GetZ());
}
speed = -liftStick.GetY();
//bool canGoUp = maxUp.Get();
bool canGoUp = true;
//bool canGoDown = maxDown.Get();
bool canGoDown = true;
//If at a limit switch and moving in that direction, stop
if (speed > 0 && !canGoUp)
speed = 0;
if (speed < 0 && !canGoDown)
speed = 0;
chainLift.SetSpeed(speed);
if (tick >50) {
if (SmartDashboard::GetBoolean("Smart Dashboard Enabled")) {
//Smart Dash outputs
//SmartDashboard::PutNumber("X Acceleration: ", accel.GetX());
//SmartDashboard::PutNumber("Y Acceleration: ", accel.GetY());
//SmartDashboard::PutNumber("Z Acceleration: ", accel.GetZ());
SmartDashboard::PutBoolean("Switch 1: (up)", maxUp.Get());
SmartDashboard::PutBoolean("Switch 2: (down)", maxDown.Get());
SmartDashboard::PutBoolean("Switch 3: (mid)", midPoint.Get());
SmartDashboard::PutBoolean("Auto switch A: ",
autoSwitch1.Get());
SmartDashboard::PutBoolean("Auto switch B: ",
autoSwitch2.Get());
//SmartDashboard::PutBoolean("RobotDrive Alive?",
// robotDrive.IsAlive());
//SmartDashboard::PutBoolean("ChainLift Alive?",
// robotDrive.IsAlive());
SmartDashboard::PutNumber("Left Sensor",
leftIR.GetAverageVoltage());
SmartDashboard::PutNumber("Right Sensor",
rightIR.GetAverageVoltage());
SmartDashboard::PutNumber("Left w zero",
leftIR.GetAverageVoltage() - leftIRZero);
SmartDashboard::PutNumber("Rigt w zero",
rightIR.GetAverageVoltage() - rightIRZero);
SmartDashboard::PutNumber("PDP 14 Current", pdp.GetCurrent(14));
SmartDashboard::PutNumber("PDP 15 Current", pdp.GetCurrent(15));
}
tick = 0;
}
}
void SwerveDrive::Update(Joystick &stick, Joystick &stick2, float gyroValue)
{
float zInput = stick.GetZ(); // Rotation Clockwise
float xInput = stick.GetX(); // Strafe
float yInput = stick.GetY(); // Forward
float temp = yInput * cos(gyroValue * M_PI / 180) + xInput * sin(gyroValue * M_PI / 180); // This block of commands SHOULD make this thing field oriented
xInput = -yInput * sin(gyroValue * M_PI / 180) + xInput * cos(gyroValue * M_PI / 180);
yInput = temp;
int *controlType;
controlType = (int *)a_ControlTypeChooser.GetSelected();
if (controlType == NULL)
{
std::cout << "error reading control type" << std::endl;
return;
}
float A = xInput - zInput * (a_RobotLength / a_ChassisRadius);
float B = xInput + zInput * (a_RobotLength / a_ChassisRadius);
float C = yInput - zInput * (a_RobotWidth / a_ChassisRadius);
float D = yInput + zInput * (a_RobotWidth / a_ChassisRadius);
float max = -9 * pow(10,4);
double frSpeed = 0.0;
double frAngle = 0.0;
double flSpeed = 0.0;
double flAngle = 0.0;
double blSpeed = 0.0;
double blAngle = 0.0;
double brSpeed = 0.0;
double brAngle = 0.0;
switch (*controlType)
{
case CONTROL_TYPE_SWERVE:
frSpeed = sqrt(pow(B,2) + pow(C,2));
flSpeed = sqrt(pow(B,2) + pow(D,2));
blSpeed = sqrt(pow(A,2) + pow(D,2));
brSpeed = sqrt(pow(A,2) + pow(C,2));
max = frSpeed;
if(flSpeed > max) {
max = flSpeed;
}
if(blSpeed > max) {
max = blSpeed;
}
if(brSpeed > max) {
max = brSpeed;
}
if(max > 1) { // This is done so that if a speed greater than 1 is calculated, all are reduced proportionally
frSpeed /= max;
flSpeed /= max;
blSpeed /= max;
brSpeed /= max;
}
// atan2 outputs values in a manner similar to what is shown on the below diagram
////////////////////
// 0 //
// // //
// // //
// // //
//-90///////////90//
// // //
// // //
// // //
// -180 or 180 //
////////////////////
frAngle = (atan2(C,B) * 180.0 / M_PI);
flAngle = (atan2(D,B) * 180.0 / M_PI);
blAngle = (atan2(D,A) * 180.0 / M_PI);
brAngle = (atan2(C,A) * 180.0 / M_PI);
// If on the left side, add 360 to normalize values to the below diagram
////////////////////
// 360 or 0 //
// // //
// // //
// // //
//270///////////90//
// // //
// // //
// // //
// 180 //
////////////////////
if(frAngle < 0) {
frAngle += 360;
}
if(flAngle < 0) {
flAngle += 360;
}
if(brAngle < 0) {
brAngle += 360;
}
if(blAngle < 0) {
blAngle += 360;
}
break;
case CONTROL_TYPE_CRAB:
float setAngle = atan2(yInput,xInput) * 180.0 / M_PI; // find the angle the stick is pointed to, use that for all wheels
frAngle = setAngle;
flAngle = setAngle;
blAngle = setAngle;
brAngle = setAngle;
float setSpeed = sqrt(pow(xInput,2) + pow(yInput,2)); // find the r of the joystick vector, if you think about it in polar coordinates
frSpeed = setSpeed;
flSpeed = setSpeed;
blSpeed = setSpeed;
brSpeed = setSpeed;
break;
}
a_FrontRight.Set(frAngle, frSpeed);
a_FrontLeft.Set(flAngle, flSpeed);
a_BackLeft.Set(blAngle, blSpeed);
a_BackRight.Set(brAngle, brSpeed);
}
void OperatorControl()
{
while (IsOperatorControl() && IsEnabled())
{
robotDrive.ArcadeDrive(scaler(stick.GetZ()),scaler(stick.GetY()));
SmartDashboard::PutNumber("StickZ",stick.GetZ());
SmartDashboard::PutNumber("StickZscaled",scaler(stick.GetZ()));
finger_Motor.Set(scaler(stick2.GetRawAxis(thumbpadL_Y)));
// scalerValue = stick.GetRawAxis(3);
arm_Motor.Set(scaler(stick2.GetRawAxis(thumbpadR_Y)));
manualShooter();
shootingModes();
toggleIntake();
toggleIntakeMode();
setScalerValue();
// double volts = ourRangefinder->GetVoltage();
// SmartDashboard::PutNumber("Voltage",volts);
//t_motor.Set(stick2.GetZ());
//t_motor.Set(stick.GetAxis(Joystick::kDefaultThrottleAxis));
// t_motor.Set(stick.GetAxis(Joystick::kThrottleAxis));
// finger_Motor.Set(stick2.GetAxis(Joystick::kThrottleAxis));
// arm_Motor.Set(stick2.GetY());
// Current Control mode Debug
SmartDashboard::PutNumber("Motor30 Current",t_motor.GetOutputCurrent());
SmartDashboard::PutNumber("Position",t_motor.GetPosition());
// t_motor.Set(stick.GetAxis(Joystick::Slider));
// if (stick.GetRawButton(3) == true){
// t_motor.SetPosition(10000);
// }
// if (stick2.GetRawButton(7) == true and buttonpress == false){
//
// }
// else if (stick2.GetRawButton(3) == false and buttonpress == true){
// buttonpress = false;// drive with arcade style (use right stick)
//
// }
SmartDashboard::PutBoolean("buttonpress state",buttonpress);
if (stick2.GetRawButton(buttonBack) == true){
stateDisarmed = true;
stateArming1 = false;
stateArming2 = false;
stateArmed = false;
stateFiring1 = false;
stateFiring2 = false;
t_motor.SetPosition(0);
}
toggleIntake();
// if (stick2.GetRawButton(5) == true){
// intake_Spin_Motor.Set(1);
// }
// if (stick2.GetRawButton(5) == false){
// intake_Spin_Motor.Set(0);
// }
if (stick.GetRawButton(2) == true and buttonpress2 == false){
myServo->SetAngle(175);
}
if (stick.GetRawButton(2) == false and buttonpress2 == true){
myServo->SetAngle(5);
}
// servoSetPos(servoState);
// myServo->Set(.5);
Wait(0.005);// wait for a motor update time
// motorSetPos(launcherState);
}
}
void TeleopPeriodic(void) {
// increment the number of teleop periodic loops completed
GetWatchdog().Feed();
m_telePeriodicLoops++;
/*
* No longer needed since periodic loops are now synchronized with incoming packets.
if (m_ds->GetPacketNumber() != m_priorPacketNumber) {
*/
/*
* Code placed in here will be called only when a new packet of information
* has been received by the Driver Station. Any code which needs new information
* from the DS should go in here
*/
m_dsPacketsReceivedInCurrentSecond++; // increment DS packets received
// put Driver Station-dependent code here
// Demonstrate the use of the Joystick buttons
// DemonstrateJoystickButtons(m_rightStick, m_rightStickButtonState, "Right Stick", &m_solenoids[1]);
// DemonstrateJoystickButtons(m_leftStick, m_leftStickButtonState, "Left Stick ", &m_solenoids[5]);
/***
// determine if tank or arcade mode, based upon position of "Z" wheel on kit joystick
if (m_rightStick->GetZ() <= 0) { // Logitech Attack3 has z-polarity reversed; up is negative
// use arcade drive
m_robotDrive->ArcadeDrive(m_rightStick); // drive with arcade style (use right stick)
if (m_driveMode != ARCADE_DRIVE) {
// if newly entered arcade drive, print out a message
printf("Arcade Drive\n");
m_driveMode = ARCADE_DRIVE;
}
} else {
// use tank drive
m_robotDrive->TankDrive(m_leftStick, m_rightStick); // drive with tank style
if (m_driveMode != TANK_DRIVE) {
// if newly entered tank drive, print out a message
printf("Tank Drive\n");
m_driveMode = TANK_DRIVE;
}
}
***/
/* Grab z-wheel value and transform from [1, -1] to [0,4600]
* 4600 rpm is a guess */
float rawZ, transformedZ;
rawZ = m_leftStick->GetZ();
// transformedZ = (1.0 - rawZ)/(-2.0);
transformedZ = -2300.0 * rawZ + 2300.0;
/* Driver station display output. */
char msg[256];
static DriverStationLCD *dsLCD = DriverStationLCD::GetInstance();
sprintf(msg, "Launcher Speed = %f RPM", transformedZ);
dsLCD->Printf(DriverStationLCD::kUser_Line1, 1, msg);
sprintf(msg, "Loader Limit = %u", m_loaderLimit->Get());
dsLCD->Printf(DriverStationLCD::kUser_Line2, 1, msg);
sprintf(msg, "Loader Trigger = %u", m_leftStick->GetTrigger());
dsLCD->Printf(DriverStationLCD::kUser_Line3, 1, msg);
// line number (enum), starting col, format string, args for format string ...
dsLCD->UpdateLCD();
// use arcade drive
//m_driveGain = (1.0 - m_rightStick->GetZ())/(-2.0);
m_robot->ArcadeDrive(m_rightStick); // drive with arcade style (use right stick)
// m_robotFrontDrive->Drive(-m_driveGain*m_rightStick->GetY(),-m_driveGain*m_rightStick->GetX()); // negative sign to fix bug in turn
// m_robotRearDrive->Drive(m_driveGain*m_rightStick->GetY(),-m_driveGain*m_rightStick->GetX()); // negative sign to fix bug in turn
// -Add an elevation control, add a motor controller to port 8, and add a joystick button pair to control up/down
if (m_rightStick->GetRawButton(m_elevatorUpButton)){
m_elevatorMotor->Set(m_elevatorUpSpeed);
}
else if (m_rightStick->GetRawButton(m_elevatorDownButton)){
m_elevatorMotor->Set(m_elevatorDownSpeed);
}
else {
m_elevatorMotor->Set(0.0);
}
// trigger button activates feeding and loading mechanisms
if ((m_leftStick->GetTop() || m_feeding) && (!m_loading) && (m_feedCounter <= m_feedCount)){
m_feeding = true;
m_feedCounter++;
m_feedMotor->Set(m_feedSpeed);
}
else {
m_feeding = false;
m_feedCounter = 0;
m_feedMotor->Set(0.);
}
m_loaderLimit->Get(); //just testing digital input port 1
// top(2) button uses the Z wheel to control the speed of the loading mechanisms
if (((m_leftStick->GetTrigger() || m_loading) && (!m_feeding)) && (m_loadCounter <= m_loadCount)){//comment out this line
// if (((m_leftStick->GetTrigger() || m_loading) && (!m_feeding)) && (bool) m_loaderLimit->Get()){ //uncomment this line
m_loading = true;
m_loadCounter++; // comment out this line
m_loadMotor->Set(m_loadSpeed); // load breech
}
else if ((m_loading && (!m_feeding)) && (m_loadCounter > m_loadCount) && (m_loadCounter <= ((m_loadCount+m_loadPauseCount)))) { // comment out the pause logic
m_loading = true;// comment out the pause logic
m_loadCounter++;// comment out the pause logic,
m_loadMotor->Set(0.); // pause loader // comment out the pause logic
}
// else if ((m_loading && (!m_feeding)) && (m_loadCounter >= (m_loadCount+m_loadPauseCount)) && (m_loadCounter<= 2*m_loadCount-13)) { // comment out this line
else if ((m_loading && (!m_feeding)) && (m_loadCounter >= (m_loadCount+m_loadPauseCount)) && (m_loaderLimit->Get()!=0)) {
//Retracting loader arm (feeder), have not yet hit the limit switch.
// else if ((m_loading &! m_feeding) && (bool) m_loaderResetLimit->Get()) { // uncomment this line
m_loading = true;
m_loadCounter++; // comment out the pause logic
m_loadMotor->Set(-m_loadSpeed);; // reset loader
}
else {
//Finished retracting loader arm (feeder), so stop it.
m_loading = false;
m_loadCounter = 0;
m_loadMotor->Set(0.);; // stop loader
}
// Set launcher motor command
m_launchMotor->Set(-(1.0 - m_leftStick->GetZ())/(-2.0)); // transform from [-1.0, +1.0] to [0.0, +1.0]
/*
} // if (m_ds->GetPacketNumber()...
*/
// use buttons 8 and 9 to trim load motor position in maintenance mode
/*if (m_leftStick->GetRawButton(8) && (!m_feeding) && (!m_loading)){
m_loadMotor->Set(0.12);
}
else if (m_leftStick->GetRawButton(9) && (!m_feeding) && (!m_loading)){
m_loadMotor->Set(-0.1);
}*/
//Use buttons 10 and 11 to trim feed motor position in maintenance mode
if (m_leftStick->GetRawButton(11) && (!m_feeding) && (!m_loading)){
m_feedMotor->Set(0.15);
}
else if (m_leftStick->GetRawButton(10) && (!m_feeding) && (!m_loading)){
m_feedMotor->Set(-0.1);
}
} // TeleopPeriodic(void)