C++ (Cpp) MUX_VAL Beispiele

Beispiel #1

0

Datei anzeigen

Datei: logic-data.c Projekt: Aircell/asp-u-boot

/* Restore SCLK/SDA pins connected to the product ID chip */
static void gpio_i2c_restore_pins(void)
{
	/* Restore I2C3_SCL/I2C_DATA into safe mode; kernel repsonsible
	 * for muxing I2C3 */
	MUX_VAL(CP(I2C3_SCL),       (IEN  | PTD | EN  | M7)); /*I2C3_SCL*/
	MUX_VAL(CP(I2C3_SDA),       (IEN  | PTD | EN  | M7)); /*I2C3_SDA*/
}

Beispiel #2

0

Datei anzeigen

Datei: mt_ventoux.c Projekt: OpenNoah/u-boot

/*
 * Routine: board_init
 * Description: Early hardware init.
 */
int board_init(void)
{
	gpmc_init(); /* in SRAM or SDRAM, finish GPMC */

	/* boot param addr */
	gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);

	mt_ventoux_init_fpga();

	/* GPIO_140: speaker #mute */
	MUX_VAL(CP(MCBSP3_DX),		(IEN | PTU | EN | M4))
	/* GPIO_141: Buzz Hi */
	MUX_VAL(CP(MCBSP3_DR),		(IEN  | PTU | EN | M4))

	/* Turning off the buzzer */
	gpio_request(BUZZER, "BUZZER_MUTE");
	gpio_request(SPEAKER, "SPEAKER");
	gpio_direction_output(BUZZER, 0);
	gpio_direction_output(SPEAKER, 0);

	/* Activate USB power */
	gpio_request(USB1_PWR, "USB1_PWR");
	gpio_request(USB2_PWR, "USB2_PWR");
	gpio_direction_output(USB1_PWR, 1);
	gpio_direction_output(USB2_PWR, 1);

	return 0;
}

Beispiel #3

0

Datei anzeigen

Datei: omap3621_boxer_panel.c Projekt: mali1/u-boot-encore

void lcd_enable(void)
{
    if (lcd_disabled) {
        lcd_ctrl_init(lcd_set_base);
    }

    gpio_pin_init(36, GPIO_OUTPUT, 1);

    // Wait one ms before sending down SPI init sequence
    udelay(1000);

    MUX_VAL(CP(McBSP1_CLKR),    (OFF_IN_PD  | IEN  | PTD | DIS | M4))  /*McSPI4-CLK*/ \
    MUX_VAL(CP(McBSP1_DX),      (OFF_IN_PD  | IDIS | PTD | DIS | M4))   /*McSPI4-SIMO*/ \
    MUX_VAL(CP(McBSP1_DR),      (OFF_IN_PD  | IEN  | PTD | DIS | M4))  /*McSPI4-SOMI*/\
    MUX_VAL(CP(McBSP1_FSX),     (OFF_IN_PD  | IEN  | PTU | DIS | M4))  /*McSPI4-CS0*/
   
    gpio_pin_init(GPIO_SPI_CLK,GPIO_OUTPUT,1);  
    gpio_pin_init(GPIO_SPI_SIMO,GPIO_OUTPUT,1);   
    gpio_pin_init(GPIO_SPI_CS,GPIO_OUTPUT,1);  

    gpio_pin_init(GPIO_SPI_SOMI,GPIO_INPUT,1);   
  
	boxer_init_panel();
    
    omap3_dss_enable();
    enable_backlight();
    lcd_disabled = 0;
}

Beispiel #4

0

Datei anzeigen

Datei: mcbsp_utils.c Projekt: onealtom/craneboard-itbok

/*
** Routine to configure PIN MULTIPLEXING.
** This function sets up the system control muxes to route mcbsp.
*/
void mux_setup_mcbsp(void)
{
    /*
     ** Pin and Pad settings for McBSP.
     */
    MUX_VAL(CP(MCBSP2_FSX), (IEN | PTD | DIS | M0));
    MUX_VAL(CP(MCBSP2_CLKX), (IEN | PTD | DIS | M0));
    MUX_VAL(CP(MCBSP2_DR), (IEN | PTD | DIS | M0));
    MUX_VAL(CP(MCBSP2_DX), (IDIS | PTD | DIS | M0));
}

Beispiel #5

0

Datei anzeigen

Datei: omap3621_boxer_panel.c Projekt: mali1/u-boot-encore

void lcd_disable(void)
{
    disable_backlight();

    sr32(CM_FCLKEN_DSS, 0, 32, 0x0);
	sr32(CM_ICLKEN_DSS, 0, 32, 0x0); 

    gpio_pin_write(36, 0);

    // Restore SPI registers
    MUX_VAL(CP(McBSP1_CLKR),    (IEN  | PTD | DIS | M1)) /*McSPI4-CLK*/ \
    MUX_VAL(CP(McBSP1_DX),      (IDIS | PTD | DIS | M1)) /*McSPI4-SIMO*/ \
    MUX_VAL(CP(McBSP1_DR),      (IEN  | PTD | DIS | M1)) /*McSPI4-SOMI*/\
    MUX_VAL(CP(McBSP1_FSX),     (IDIS | PTD | DIS | M1)) /*McSPI4-CS0*/

    lcd_disabled = 1;
}

Beispiel #6

0

Datei anzeigen

Datei: tao3530.c Projekt: 01hyang/u-boot

int tao3530_revision(void)
{
	int ret = 0;

	/* char *label argument is unused in gpio_request() */
	ret = gpio_request(65, "");
	if (ret) {
		puts("Error: GPIO 65 not available\n");
		goto out;
	}
	MUX_VAL(CP(GPMC_WAIT3),	(IEN  | PTU | EN  | M4));

	ret = gpio_request(1, "");
	if (ret) {
		puts("Error: GPIO 1 not available\n");
		goto out2;
	}
	MUX_VAL(CP(SYS_CLKREQ), (IEN  | PTU | EN | M4));

	ret = gpio_direction_input(65);
	if (ret) {
		puts("Error: GPIO 65 not available for input\n");
		goto out3;
	}

	ret =  gpio_direction_input(1);
	if (ret) {
		puts("Error: GPIO 1 not available for input\n");
		goto out3;
	}

	ret = gpio_get_value(65) << 1 | gpio_get_value(1);

out3:
	MUX_VAL(CP(SYS_CLKREQ), (IEN  | PTU | EN | M0));
	gpio_free(1);
out2:
	MUX_VAL(CP(GPMC_WAIT3),	(IEN  | PTU | EN  | M0));
	gpio_free(65);
out:

	return ret;
}

Beispiel #7

0

Datei anzeigen

Datei: mac_evm.c Projekt: onealtom/craneboard-itbok

void reset_smscChip(void)
{
	int i = 0;
	/* do a hard reset */
	//GPIO 7 configuration in CONTROL_PADCONF_SYS_BOOT5 register mux mode is 4.
	MUX_VAL(CP(SYS_BOOT5), (IEN | PTU | EN | M4))
	    // Enable Clock for GPIO 1-6 module in CM_FCLKEN_PER and CM_ICLKEN_PER registers
	    writel(readl(CM_FCLKEN_PER) | 0x0003E800, CM_FCLKEN_PER);
	writel(readl(CM_ICLKEN_PER) | 0x0003E800, CM_ICLKEN_PER);

	// Make GPIO 7 as output pin 
	writel(readl(OMAP34XX_GPIO1_BASE + GPIO_OE) & ~BIT(7), OMAP34XX_GPIO3_BASE + GPIO_OE);

	// Now send a pulse on the GPIO pin
	writel(readl(OMAP34XX_GPIO1_BASE + GPIO_DATAOUT) | BIT(7), OMAP34XX_GPIO3_BASE + GPIO_DATAOUT);
	for (i = 0; i < 99; i++) ;
	writel(readl(OMAP34XX_GPIO1_BASE + GPIO_DATAOUT) & ~BIT(7), OMAP34XX_GPIO3_BASE + GPIO_DATAOUT);
	mdelay(100);
	for (i = 0; i < 99; i++) ;
	writel(readl(OMAP34XX_GPIO1_BASE + GPIO_DATAOUT) | BIT(7), OMAP34XX_GPIO3_BASE + GPIO_DATAOUT);
	mdelay(100);

}

Beispiel #8

0

Datei anzeigen

Datei: cm_t35.c Projekt: Analias/SNOWLeo-SDR-1

static void cm_t35_set_muxconf(void)
{
	/* DSS */
	MUX_VAL(CP(DSS_DATA0),		(IDIS | PTD | DIS | M0)); /*DSS_DATA0*/
	MUX_VAL(CP(DSS_DATA1),		(IDIS | PTD | DIS | M0)); /*DSS_DATA1*/
	MUX_VAL(CP(DSS_DATA2),		(IDIS | PTD | DIS | M0)); /*DSS_DATA2*/
	MUX_VAL(CP(DSS_DATA3),		(IDIS | PTD | DIS | M0)); /*DSS_DATA3*/
	MUX_VAL(CP(DSS_DATA4),		(IDIS | PTD | DIS | M0)); /*DSS_DATA4*/
	MUX_VAL(CP(DSS_DATA5),		(IDIS | PTD | DIS | M0)); /*DSS_DATA5*/

	MUX_VAL(CP(DSS_DATA18),         (IDIS | PTD | DIS | M0)); /*DSS_DATA18*/
	MUX_VAL(CP(DSS_DATA19),         (IDIS | PTD | DIS | M0)); /*DSS_DATA19*/
	MUX_VAL(CP(DSS_DATA20),         (IDIS | PTD | DIS | M0)); /*DSS_DATA20*/
	MUX_VAL(CP(DSS_DATA21),         (IDIS | PTD | DIS | M0)); /*DSS_DATA21*/
	MUX_VAL(CP(DSS_DATA22),         (IDIS | PTD | DIS | M0)); /*DSS_DATA22*/
	MUX_VAL(CP(DSS_DATA23),         (IDIS | PTD | DIS | M0)); /*DSS_DATA23*/

	/* MMC1 */
	MUX_VAL(CP(MMC1_DAT4),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT4*/
	MUX_VAL(CP(MMC1_DAT5),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT5*/
	MUX_VAL(CP(MMC1_DAT6),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT6*/
	MUX_VAL(CP(MMC1_DAT7),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT7*/
}

Beispiel #9

0

Datei anzeigen

Datei: cm_t35.c Projekt: Analias/SNOWLeo-SDR-1

/*
 * Routine: set_muxconf_regs
 * Description: Setting up the configuration Mux registers specific to the
 *		hardware. Many pins need to be moved from protect to primary
 *		mode.
 */
static void cm_t3x_set_common_muxconf(void)
{
	/* SDRC */
	MUX_VAL(CP(SDRC_D0),		(IEN  | PTD | DIS | M0)); /*SDRC_D0*/
	MUX_VAL(CP(SDRC_D1),		(IEN  | PTD | DIS | M0)); /*SDRC_D1*/
	MUX_VAL(CP(SDRC_D2),		(IEN  | PTD | DIS | M0)); /*SDRC_D2*/
	MUX_VAL(CP(SDRC_D3),		(IEN  | PTD | DIS | M0)); /*SDRC_D3*/
	MUX_VAL(CP(SDRC_D4),		(IEN  | PTD | DIS | M0)); /*SDRC_D4*/
	MUX_VAL(CP(SDRC_D5),		(IEN  | PTD | DIS | M0)); /*SDRC_D5*/
	MUX_VAL(CP(SDRC_D6),		(IEN  | PTD | DIS | M0)); /*SDRC_D6*/
	MUX_VAL(CP(SDRC_D7),		(IEN  | PTD | DIS | M0)); /*SDRC_D7*/
	MUX_VAL(CP(SDRC_D8),		(IEN  | PTD | DIS | M0)); /*SDRC_D8*/
	MUX_VAL(CP(SDRC_D9),		(IEN  | PTD | DIS | M0)); /*SDRC_D9*/
	MUX_VAL(CP(SDRC_D10),		(IEN  | PTD | DIS | M0)); /*SDRC_D10*/
	MUX_VAL(CP(SDRC_D11),		(IEN  | PTD | DIS | M0)); /*SDRC_D11*/
	MUX_VAL(CP(SDRC_D12),		(IEN  | PTD | DIS | M0)); /*SDRC_D12*/
	MUX_VAL(CP(SDRC_D13),		(IEN  | PTD | DIS | M0)); /*SDRC_D13*/
	MUX_VAL(CP(SDRC_D14),		(IEN  | PTD | DIS | M0)); /*SDRC_D14*/
	MUX_VAL(CP(SDRC_D15),		(IEN  | PTD | DIS | M0)); /*SDRC_D15*/
	MUX_VAL(CP(SDRC_D16),		(IEN  | PTD | DIS | M0)); /*SDRC_D16*/
	MUX_VAL(CP(SDRC_D17),		(IEN  | PTD | DIS | M0)); /*SDRC_D17*/
	MUX_VAL(CP(SDRC_D18),		(IEN  | PTD | DIS | M0)); /*SDRC_D18*/
	MUX_VAL(CP(SDRC_D19),		(IEN  | PTD | DIS | M0)); /*SDRC_D19*/
	MUX_VAL(CP(SDRC_D20),		(IEN  | PTD | DIS | M0)); /*SDRC_D20*/
	MUX_VAL(CP(SDRC_D21),		(IEN  | PTD | DIS | M0)); /*SDRC_D21*/
	MUX_VAL(CP(SDRC_D22),		(IEN  | PTD | DIS | M0)); /*SDRC_D22*/
	MUX_VAL(CP(SDRC_D23),		(IEN  | PTD | DIS | M0)); /*SDRC_D23*/
	MUX_VAL(CP(SDRC_D24),		(IEN  | PTD | DIS | M0)); /*SDRC_D24*/
	MUX_VAL(CP(SDRC_D25),		(IEN  | PTD | DIS | M0)); /*SDRC_D25*/
	MUX_VAL(CP(SDRC_D26),		(IEN  | PTD | DIS | M0)); /*SDRC_D26*/
	MUX_VAL(CP(SDRC_D27),		(IEN  | PTD | DIS | M0)); /*SDRC_D27*/
	MUX_VAL(CP(SDRC_D28),		(IEN  | PTD | DIS | M0)); /*SDRC_D28*/
	MUX_VAL(CP(SDRC_D29),		(IEN  | PTD | DIS | M0)); /*SDRC_D29*/
	MUX_VAL(CP(SDRC_D30),		(IEN  | PTD | DIS | M0)); /*SDRC_D30*/
	MUX_VAL(CP(SDRC_D31),		(IEN  | PTD | DIS | M0)); /*SDRC_D31*/
	MUX_VAL(CP(SDRC_CLK),		(IEN  | PTD | DIS | M0)); /*SDRC_CLK*/
	MUX_VAL(CP(SDRC_DQS0),		(IEN  | PTD | DIS | M0)); /*SDRC_DQS0*/
	MUX_VAL(CP(SDRC_DQS1),		(IEN  | PTD | DIS | M0)); /*SDRC_DQS1*/
	MUX_VAL(CP(SDRC_DQS2),		(IEN  | PTD | DIS | M0)); /*SDRC_DQS2*/
	MUX_VAL(CP(SDRC_DQS3),		(IEN  | PTD | DIS | M0)); /*SDRC_DQS3*/
	MUX_VAL(CP(SDRC_CKE0),		(IDIS | PTU | EN  | M0)); /*SDRC_CKE0*/
	MUX_VAL(CP(SDRC_CKE1),		(IDIS | PTD | DIS | M7)); /*SDRC_CKE1*/

	/* GPMC */
	MUX_VAL(CP(GPMC_A1),		(IDIS | PTU | EN  | M0)); /*GPMC_A1*/
	MUX_VAL(CP(GPMC_A2),		(IDIS | PTU | EN  | M0)); /*GPMC_A2*/
	MUX_VAL(CP(GPMC_A3),		(IDIS | PTU | EN  | M0)); /*GPMC_A3*/
	MUX_VAL(CP(GPMC_A4),		(IDIS | PTU | EN  | M0)); /*GPMC_A4*/
	MUX_VAL(CP(GPMC_A5),		(IDIS | PTU | EN  | M0)); /*GPMC_A5*/
	MUX_VAL(CP(GPMC_A6),		(IDIS | PTU | EN  | M0)); /*GPMC_A6*/
	MUX_VAL(CP(GPMC_A7),		(IDIS | PTU | EN  | M0)); /*GPMC_A7*/
	MUX_VAL(CP(GPMC_A8),		(IDIS | PTU | EN  | M0)); /*GPMC_A8*/
	MUX_VAL(CP(GPMC_A9),		(IDIS | PTU | EN  | M0)); /*GPMC_A9*/
	MUX_VAL(CP(GPMC_A10),		(IDIS | PTU | EN  | M0)); /*GPMC_A10*/
	MUX_VAL(CP(GPMC_D0),		(IEN  | PTU | EN  | M0)); /*GPMC_D0*/
	MUX_VAL(CP(GPMC_D1),		(IEN  | PTU | EN  | M0)); /*GPMC_D1*/
	MUX_VAL(CP(GPMC_D2),		(IEN  | PTU | EN  | M0)); /*GPMC_D2*/
	MUX_VAL(CP(GPMC_D3),		(IEN  | PTU | EN  | M0)); /*GPMC_D3*/
	MUX_VAL(CP(GPMC_D4),		(IEN  | PTU | EN  | M0)); /*GPMC_D4*/
	MUX_VAL(CP(GPMC_D5),		(IEN  | PTU | EN  | M0)); /*GPMC_D5*/
	MUX_VAL(CP(GPMC_D6),		(IEN  | PTU | EN  | M0)); /*GPMC_D6*/
	MUX_VAL(CP(GPMC_D7),		(IEN  | PTU | EN  | M0)); /*GPMC_D7*/
	MUX_VAL(CP(GPMC_D8),		(IEN  | PTU | EN  | M0)); /*GPMC_D8*/
	MUX_VAL(CP(GPMC_D9),		(IEN  | PTU | EN  | M0)); /*GPMC_D9*/
	MUX_VAL(CP(GPMC_D10),		(IEN  | PTU | EN  | M0)); /*GPMC_D10*/
	MUX_VAL(CP(GPMC_D11),		(IEN  | PTU | EN  | M0)); /*GPMC_D11*/
	MUX_VAL(CP(GPMC_D12),		(IEN  | PTU | EN  | M0)); /*GPMC_D12*/
	MUX_VAL(CP(GPMC_D13),		(IEN  | PTU | EN  | M0)); /*GPMC_D13*/
	MUX_VAL(CP(GPMC_D14),		(IEN  | PTU | EN  | M0)); /*GPMC_D14*/
	MUX_VAL(CP(GPMC_D15),		(IEN  | PTU | EN  | M0)); /*GPMC_D15*/
	MUX_VAL(CP(GPMC_NCS0),		(IDIS | PTU | EN  | M0)); /*GPMC_nCS0*/

	/* SB-T35 Ethernet */
	MUX_VAL(CP(GPMC_NCS4),		(IEN  | PTU | EN  | M0)); /*GPMC_nCS4*/

	/* CM-T3x Ethernet */
	MUX_VAL(CP(GPMC_NCS5),		(IDIS | PTU | DIS | M0)); /*GPMC_nCS5*/
	MUX_VAL(CP(GPMC_CLK),		(IEN  | PTD | DIS | M4)); /*GPIO_59*/
	MUX_VAL(CP(GPMC_NADV_ALE),	(IDIS | PTD | DIS | M0)); /*nADV_ALE*/
	MUX_VAL(CP(GPMC_NOE),		(IDIS | PTD | DIS | M0)); /*nOE*/
	MUX_VAL(CP(GPMC_NWE),		(IDIS | PTD | DIS | M0)); /*nWE*/
	MUX_VAL(CP(GPMC_NBE0_CLE),	(IDIS | PTU | EN  | M0)); /*nBE0_CLE*/
	MUX_VAL(CP(GPMC_NBE1),		(IDIS | PTD | DIS | M4)); /*GPIO_61*/
	MUX_VAL(CP(GPMC_NWP),		(IEN  | PTD | DIS | M0)); /*nWP*/
	MUX_VAL(CP(GPMC_WAIT0),		(IEN  | PTU | EN  | M0)); /*WAIT0*/

	/* DSS */
	MUX_VAL(CP(DSS_PCLK),		(IDIS | PTD | DIS | M0)); /*DSS_PCLK*/
	MUX_VAL(CP(DSS_HSYNC),		(IDIS | PTD | DIS | M0)); /*DSS_HSYNC*/
	MUX_VAL(CP(DSS_VSYNC),		(IDIS | PTD | DIS | M0)); /*DSS_VSYNC*/
	MUX_VAL(CP(DSS_ACBIAS),		(IDIS | PTD | DIS | M0)); /*DSS_ACBIAS*/
	MUX_VAL(CP(DSS_DATA6),		(IDIS | PTD | DIS | M0)); /*DSS_DATA6*/
	MUX_VAL(CP(DSS_DATA7),		(IDIS | PTD | DIS | M0)); /*DSS_DATA7*/
	MUX_VAL(CP(DSS_DATA8),		(IDIS | PTD | DIS | M0)); /*DSS_DATA8*/
	MUX_VAL(CP(DSS_DATA9),		(IDIS | PTD | DIS | M0)); /*DSS_DATA9*/
	MUX_VAL(CP(DSS_DATA10),		(IDIS | PTD | DIS | M0)); /*DSS_DATA10*/
	MUX_VAL(CP(DSS_DATA11),		(IDIS | PTD | DIS | M0)); /*DSS_DATA11*/
	MUX_VAL(CP(DSS_DATA12),		(IDIS | PTD | DIS | M0)); /*DSS_DATA12*/
	MUX_VAL(CP(DSS_DATA13),		(IDIS | PTD | DIS | M0)); /*DSS_DATA13*/
	MUX_VAL(CP(DSS_DATA14),		(IDIS | PTD | DIS | M0)); /*DSS_DATA14*/
	MUX_VAL(CP(DSS_DATA15),		(IDIS | PTD | DIS | M0)); /*DSS_DATA15*/
	MUX_VAL(CP(DSS_DATA16),		(IDIS | PTD | DIS | M0)); /*DSS_DATA16*/
	MUX_VAL(CP(DSS_DATA17),		(IDIS | PTD | DIS | M0)); /*DSS_DATA17*/

	/* serial interface */
	MUX_VAL(CP(UART3_RX_IRRX),	(IEN  | PTD | DIS | M0)); /*UART3_RX*/
	MUX_VAL(CP(UART3_TX_IRTX),	(IDIS | PTD | DIS | M0)); /*UART3_TX*/

	/* mUSB */
	MUX_VAL(CP(HSUSB0_CLK),		(IEN  | PTD | DIS | M0)); /*HSUSB0_CLK*/
	MUX_VAL(CP(HSUSB0_STP),		(IDIS | PTU | EN  | M0)); /*HSUSB0_STP*/
	MUX_VAL(CP(HSUSB0_DIR),		(IEN  | PTD | DIS | M0)); /*HSUSB0_DIR*/
	MUX_VAL(CP(HSUSB0_NXT),		(IEN  | PTD | DIS | M0)); /*HSUSB0_NXT*/
	MUX_VAL(CP(HSUSB0_DATA0),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA0*/
	MUX_VAL(CP(HSUSB0_DATA1),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA1*/
	MUX_VAL(CP(HSUSB0_DATA2),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA2*/
	MUX_VAL(CP(HSUSB0_DATA3),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA3*/
	MUX_VAL(CP(HSUSB0_DATA4),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA4*/
	MUX_VAL(CP(HSUSB0_DATA5),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA5*/
	MUX_VAL(CP(HSUSB0_DATA6),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA6*/
	MUX_VAL(CP(HSUSB0_DATA7),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA7*/

	/* I2C1 */
	MUX_VAL(CP(I2C1_SCL),		(IEN  | PTU | EN  | M0)); /*I2C1_SCL*/
	MUX_VAL(CP(I2C1_SDA),		(IEN  | PTU | EN  | M0)); /*I2C1_SDA*/
	/* I2C2 */
	MUX_VAL(CP(I2C2_SCL),		(IEN  | PTU | EN  | M0)); /*I2C2_SCL*/
	MUX_VAL(CP(I2C2_SDA),		(IEN  | PTU | EN  | M0)); /*I2C2_SDA*/
	/* I2C3 */
	MUX_VAL(CP(I2C3_SCL),		(IEN  | PTU | EN  | M0)); /*I2C3_SCL*/
	MUX_VAL(CP(I2C3_SDA),		(IEN  | PTU | EN  | M0)); /*I2C3_SDA*/

	/* control and debug */
	MUX_VAL(CP(SYS_32K),		(IEN  | PTD | DIS | M0)); /*SYS_32K*/
	MUX_VAL(CP(SYS_CLKREQ),		(IEN  | PTD | DIS | M0)); /*SYS_CLKREQ*/
	MUX_VAL(CP(SYS_NIRQ),		(IEN  | PTU | EN  | M0)); /*SYS_nIRQ*/
	MUX_VAL(CP(SYS_OFF_MODE),	(IEN  | PTD | DIS | M0)); /*OFF_MODE*/
	MUX_VAL(CP(SYS_CLKOUT1),	(IEN  | PTD | DIS | M0)); /*CLKOUT1*/
	MUX_VAL(CP(SYS_CLKOUT2),	(IDIS | PTU | DIS | M4)); /*green LED*/
	MUX_VAL(CP(JTAG_nTRST),		(IEN  | PTD | DIS | M0)); /*JTAG_nTRST*/
	MUX_VAL(CP(JTAG_TCK),		(IEN  | PTD | DIS | M0)); /*JTAG_TCK*/
	MUX_VAL(CP(JTAG_TMS),		(IEN  | PTD | DIS | M0)); /*JTAG_TMS*/
	MUX_VAL(CP(JTAG_TDI),		(IEN  | PTD | DIS | M0)); /*JTAG_TDI*/

	/* MMC1 */
	MUX_VAL(CP(MMC1_CLK),		(IDIS | PTU | EN  | M0)); /*MMC1_CLK*/
	MUX_VAL(CP(MMC1_CMD),		(IEN  | PTU | EN  | M0)); /*MMC1_CMD*/
	MUX_VAL(CP(MMC1_DAT0),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT0*/
	MUX_VAL(CP(MMC1_DAT1),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT1*/
	MUX_VAL(CP(MMC1_DAT2),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT2*/
	MUX_VAL(CP(MMC1_DAT3),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT3*/
}

Beispiel #10

0

Datei anzeigen

Datei: lowlevel.c Projekt: AshishNamdev/barebox

/**
 * @brief Do the necessary pin muxing required for OMAP3EVM. Some pins in OMAP3
 * do not have alternate modes. We don't program these pins.
 *
 * See @ref MUX_VAL for description of the muxing mode.
 *
 * @return void
 */
static void mux_config(void)
{
	/*
	 * SDRC
	 * - SDRC_D0-SDRC_D31: Default MUX mode is mode0.
	 */

	/*
	 * GPMC
	 * - GPMC_D0-GPMC_D7: Default MUX mode is mode0.
	 * - GPMC_NADV_ALE: Default MUX mode is mode0.
	 * - GPMC_NOE: Default MUX mode is mode0.
	 * - GPMC_NWE: Default MUX mode is mode0.
	 * - GPMC_WAIT0: Default MUX mode is mode0.
	 */
	MUX_VAL(CP(GPMC_A1),		(IDIS | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_A2),		(IDIS | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_A3),		(IDIS | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_A4),		(IDIS | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_A5),		(IDIS | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_A6),		(IDIS | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_A7),		(IDIS | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_A8),		(IDIS | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_A9),		(IDIS | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_A10),		(IDIS | PTD | DIS | M0));

	MUX_VAL(CP(GPMC_D8),		(IEN  | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_D9),		(IEN  | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_D10),		(IEN  | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_D11),		(IEN  | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_D12),		(IEN  | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_D13),		(IEN  | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_D14),		(IEN  | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_D15),		(IEN  | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_CLK),		(IDIS | PTD | DIS | M0));

	MUX_VAL(CP(GPMC_NBE0_CLE),	(IDIS | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_NBE1),		(IEN  | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_NWP),		(IEN  | PTD | DIS | M0));

	MUX_VAL(CP(GPMC_WAIT1),		(IEN  | PTU | EN  | M0));

	/*
	 * Serial Interface
	 */
#if defined(CONFIG_OMAP_UART1)
	MUX_VAL(CP(UART1_TX),		(IDIS | PTD | DIS | M0));
	MUX_VAL(CP(UART1_RTS),		(IDIS | PTD | DIS | M0));
	MUX_VAL(CP(UART1_CTS),		(IEN  | PTU | DIS | M0));
	MUX_VAL(CP(UART1_RX),		(IEN  | PTD | DIS | M0));
#elif defined(CONFIG_OMAP_UART3)
	MUX_VAL(CP(UART3_CTS_RCTX),	(IEN  | PTD | EN  | M0));
	MUX_VAL(CP(UART3_RTS_SD),	(IDIS | PTD | DIS | M0));
	MUX_VAL(CP(UART3_RX_IRRX),	(IEN  | PTD | DIS | M0));
	MUX_VAL(CP(UART3_TX_IRTX),	(IDIS | PTD | DIS | M0));
#endif
}

Beispiel #11

0

Datei anzeigen

Datei: cm_t35.c Projekt: 18959263172/u-boot-xlnx

/*
 * Routine: set_muxconf_regs
 * Description: Setting up the configuration Mux registers specific to the
 *		hardware. Many pins need to be moved from protect to primary
 *		mode.
 */
static void cm_t3x_set_common_muxconf(void)
{
	/* SDRC */
	MUX_VAL(CP(SDRC_D0),		(IEN  | PTD | DIS | M0)); /*SDRC_D0*/
	MUX_VAL(CP(SDRC_D1),		(IEN  | PTD | DIS | M0)); /*SDRC_D1*/
	MUX_VAL(CP(SDRC_D2),		(IEN  | PTD | DIS | M0)); /*SDRC_D2*/
	MUX_VAL(CP(SDRC_D3),		(IEN  | PTD | DIS | M0)); /*SDRC_D3*/
	MUX_VAL(CP(SDRC_D4),		(IEN  | PTD | DIS | M0)); /*SDRC_D4*/
	MUX_VAL(CP(SDRC_D5),		(IEN  | PTD | DIS | M0)); /*SDRC_D5*/
	MUX_VAL(CP(SDRC_D6),		(IEN  | PTD | DIS | M0)); /*SDRC_D6*/
	MUX_VAL(CP(SDRC_D7),		(IEN  | PTD | DIS | M0)); /*SDRC_D7*/
	MUX_VAL(CP(SDRC_D8),		(IEN  | PTD | DIS | M0)); /*SDRC_D8*/
	MUX_VAL(CP(SDRC_D9),		(IEN  | PTD | DIS | M0)); /*SDRC_D9*/
	MUX_VAL(CP(SDRC_D10),		(IEN  | PTD | DIS | M0)); /*SDRC_D10*/
	MUX_VAL(CP(SDRC_D11),		(IEN  | PTD | DIS | M0)); /*SDRC_D11*/
	MUX_VAL(CP(SDRC_D12),		(IEN  | PTD | DIS | M0)); /*SDRC_D12*/
	MUX_VAL(CP(SDRC_D13),		(IEN  | PTD | DIS | M0)); /*SDRC_D13*/
	MUX_VAL(CP(SDRC_D14),		(IEN  | PTD | DIS | M0)); /*SDRC_D14*/
	MUX_VAL(CP(SDRC_D15),		(IEN  | PTD | DIS | M0)); /*SDRC_D15*/
	MUX_VAL(CP(SDRC_D16),		(IEN  | PTD | DIS | M0)); /*SDRC_D16*/
	MUX_VAL(CP(SDRC_D17),		(IEN  | PTD | DIS | M0)); /*SDRC_D17*/
	MUX_VAL(CP(SDRC_D18),		(IEN  | PTD | DIS | M0)); /*SDRC_D18*/
	MUX_VAL(CP(SDRC_D19),		(IEN  | PTD | DIS | M0)); /*SDRC_D19*/
	MUX_VAL(CP(SDRC_D20),		(IEN  | PTD | DIS | M0)); /*SDRC_D20*/
	MUX_VAL(CP(SDRC_D21),		(IEN  | PTD | DIS | M0)); /*SDRC_D21*/
	MUX_VAL(CP(SDRC_D22),		(IEN  | PTD | DIS | M0)); /*SDRC_D22*/
	MUX_VAL(CP(SDRC_D23),		(IEN  | PTD | DIS | M0)); /*SDRC_D23*/
	MUX_VAL(CP(SDRC_D24),		(IEN  | PTD | DIS | M0)); /*SDRC_D24*/
	MUX_VAL(CP(SDRC_D25),		(IEN  | PTD | DIS | M0)); /*SDRC_D25*/
	MUX_VAL(CP(SDRC_D26),		(IEN  | PTD | DIS | M0)); /*SDRC_D26*/
	MUX_VAL(CP(SDRC_D27),		(IEN  | PTD | DIS | M0)); /*SDRC_D27*/
	MUX_VAL(CP(SDRC_D28),		(IEN  | PTD | DIS | M0)); /*SDRC_D28*/
	MUX_VAL(CP(SDRC_D29),		(IEN  | PTD | DIS | M0)); /*SDRC_D29*/
	MUX_VAL(CP(SDRC_D30),		(IEN  | PTD | DIS | M0)); /*SDRC_D30*/
	MUX_VAL(CP(SDRC_D31),		(IEN  | PTD | DIS | M0)); /*SDRC_D31*/
	MUX_VAL(CP(SDRC_CLK),		(IEN  | PTD | DIS | M0)); /*SDRC_CLK*/
	MUX_VAL(CP(SDRC_DQS0),		(IEN  | PTD | DIS | M0)); /*SDRC_DQS0*/
	MUX_VAL(CP(SDRC_DQS1),		(IEN  | PTD | DIS | M0)); /*SDRC_DQS1*/
	MUX_VAL(CP(SDRC_DQS2),		(IEN  | PTD | DIS | M0)); /*SDRC_DQS2*/
	MUX_VAL(CP(SDRC_DQS3),		(IEN  | PTD | DIS | M0)); /*SDRC_DQS3*/
	MUX_VAL(CP(SDRC_CKE0),		(IDIS | PTU | EN  | M0)); /*SDRC_CKE0*/
	MUX_VAL(CP(SDRC_CKE1),		(IDIS | PTD | DIS | M7)); /*SDRC_CKE1*/

	/* GPMC */
	MUX_VAL(CP(GPMC_A1),		(IDIS | PTU | EN  | M0)); /*GPMC_A1*/
	MUX_VAL(CP(GPMC_A2),		(IDIS | PTU | EN  | M0)); /*GPMC_A2*/
	MUX_VAL(CP(GPMC_A3),		(IDIS | PTU | EN  | M0)); /*GPMC_A3*/
	MUX_VAL(CP(GPMC_A4),		(IDIS | PTU | EN  | M0)); /*GPMC_A4*/
	MUX_VAL(CP(GPMC_A5),		(IDIS | PTU | EN  | M0)); /*GPMC_A5*/
	MUX_VAL(CP(GPMC_A6),		(IDIS | PTU | EN  | M0)); /*GPMC_A6*/
	MUX_VAL(CP(GPMC_A7),		(IDIS | PTU | EN  | M0)); /*GPMC_A7*/
	MUX_VAL(CP(GPMC_A8),		(IDIS | PTU | EN  | M0)); /*GPMC_A8*/
	MUX_VAL(CP(GPMC_A9),		(IDIS | PTU | EN  | M0)); /*GPMC_A9*/
	MUX_VAL(CP(GPMC_A10),		(IDIS | PTU | EN  | M0)); /*GPMC_A10*/
	MUX_VAL(CP(GPMC_D0),		(IEN  | PTU | EN  | M0)); /*GPMC_D0*/
	MUX_VAL(CP(GPMC_D1),		(IEN  | PTU | EN  | M0)); /*GPMC_D1*/
	MUX_VAL(CP(GPMC_D2),		(IEN  | PTU | EN  | M0)); /*GPMC_D2*/
	MUX_VAL(CP(GPMC_D3),		(IEN  | PTU | EN  | M0)); /*GPMC_D3*/
	MUX_VAL(CP(GPMC_D4),		(IEN  | PTU | EN  | M0)); /*GPMC_D4*/
	MUX_VAL(CP(GPMC_D5),		(IEN  | PTU | EN  | M0)); /*GPMC_D5*/
	MUX_VAL(CP(GPMC_D6),		(IEN  | PTU | EN  | M0)); /*GPMC_D6*/
	MUX_VAL(CP(GPMC_D7),		(IEN  | PTU | EN  | M0)); /*GPMC_D7*/
	MUX_VAL(CP(GPMC_D8),		(IEN  | PTU | EN  | M0)); /*GPMC_D8*/
	MUX_VAL(CP(GPMC_D9),		(IEN  | PTU | EN  | M0)); /*GPMC_D9*/
	MUX_VAL(CP(GPMC_D10),		(IEN  | PTU | EN  | M0)); /*GPMC_D10*/
	MUX_VAL(CP(GPMC_D11),		(IEN  | PTU | EN  | M0)); /*GPMC_D11*/
	MUX_VAL(CP(GPMC_D12),		(IEN  | PTU | EN  | M0)); /*GPMC_D12*/
	MUX_VAL(CP(GPMC_D13),		(IEN  | PTU | EN  | M0)); /*GPMC_D13*/
	MUX_VAL(CP(GPMC_D14),		(IEN  | PTU | EN  | M0)); /*GPMC_D14*/
	MUX_VAL(CP(GPMC_D15),		(IEN  | PTU | EN  | M0)); /*GPMC_D15*/
	MUX_VAL(CP(GPMC_NCS0),		(IDIS | PTU | EN  | M0)); /*GPMC_nCS0*/

	/* SB-T35 Ethernet */
	MUX_VAL(CP(GPMC_NCS4),		(IEN  | PTU | EN  | M0)); /*GPMC_nCS4*/

	/* DVI enable */
	MUX_VAL(CP(GPMC_NCS3),		(IDIS  | PTU | DIS  | M4));/*GPMC_nCS3*/

	/* DataImage backlight */
	MUX_VAL(CP(GPMC_NCS7),		(IDIS  | PTU | DIS  | M4));/*GPIO_58*/

	/* CM-T3x Ethernet */
	MUX_VAL(CP(GPMC_NCS5),		(IDIS | PTU | DIS | M0)); /*GPMC_nCS5*/
	MUX_VAL(CP(GPMC_CLK),		(IEN  | PTD | DIS | M4)); /*GPIO_59*/
	MUX_VAL(CP(GPMC_NADV_ALE),	(IDIS | PTD | DIS | M0)); /*nADV_ALE*/
	MUX_VAL(CP(GPMC_NOE),		(IDIS | PTD | DIS | M0)); /*nOE*/
	MUX_VAL(CP(GPMC_NWE),		(IDIS | PTD | DIS | M0)); /*nWE*/
	MUX_VAL(CP(GPMC_NBE0_CLE),	(IDIS | PTU | EN  | M0)); /*nBE0_CLE*/
	MUX_VAL(CP(GPMC_NBE1),		(IDIS | PTD | DIS | M4)); /*GPIO_61*/
	MUX_VAL(CP(GPMC_NWP),		(IEN  | PTD | DIS | M0)); /*nWP*/
	MUX_VAL(CP(GPMC_WAIT0),		(IEN  | PTU | EN  | M0)); /*WAIT0*/

	/* DSS */
	MUX_VAL(CP(DSS_PCLK),		(IDIS | PTD | DIS | M0)); /*DSS_PCLK*/
	MUX_VAL(CP(DSS_HSYNC),		(IDIS | PTD | DIS | M0)); /*DSS_HSYNC*/
	MUX_VAL(CP(DSS_VSYNC),		(IDIS | PTD | DIS | M0)); /*DSS_VSYNC*/
	MUX_VAL(CP(DSS_ACBIAS),		(IDIS | PTD | DIS | M0)); /*DSS_ACBIAS*/
	MUX_VAL(CP(DSS_DATA6),		(IDIS | PTD | DIS | M0)); /*DSS_DATA6*/
	MUX_VAL(CP(DSS_DATA7),		(IDIS | PTD | DIS | M0)); /*DSS_DATA7*/
	MUX_VAL(CP(DSS_DATA8),		(IDIS | PTD | DIS | M0)); /*DSS_DATA8*/
	MUX_VAL(CP(DSS_DATA9),		(IDIS | PTD | DIS | M0)); /*DSS_DATA9*/
	MUX_VAL(CP(DSS_DATA10),		(IDIS | PTD | DIS | M0)); /*DSS_DATA10*/
	MUX_VAL(CP(DSS_DATA11),		(IDIS | PTD | DIS | M0)); /*DSS_DATA11*/
	MUX_VAL(CP(DSS_DATA12),		(IDIS | PTD | DIS | M0)); /*DSS_DATA12*/
	MUX_VAL(CP(DSS_DATA13),		(IDIS | PTD | DIS | M0)); /*DSS_DATA13*/
	MUX_VAL(CP(DSS_DATA14),		(IDIS | PTD | DIS | M0)); /*DSS_DATA14*/
	MUX_VAL(CP(DSS_DATA15),		(IDIS | PTD | DIS | M0)); /*DSS_DATA15*/
	MUX_VAL(CP(DSS_DATA16),		(IDIS | PTD | DIS | M0)); /*DSS_DATA16*/
	MUX_VAL(CP(DSS_DATA17),		(IDIS | PTD | DIS | M0)); /*DSS_DATA17*/

	/* serial interface */
	MUX_VAL(CP(UART3_RX_IRRX),	(IEN  | PTD | DIS | M0)); /*UART3_RX*/
	MUX_VAL(CP(UART3_TX_IRTX),	(IDIS | PTD | DIS | M0)); /*UART3_TX*/

	/* mUSB */
	MUX_VAL(CP(HSUSB0_CLK),		(IEN  | PTD | DIS | M0)); /*HSUSB0_CLK*/
	MUX_VAL(CP(HSUSB0_STP),		(IDIS | PTU | EN  | M0)); /*HSUSB0_STP*/
	MUX_VAL(CP(HSUSB0_DIR),		(IEN  | PTD | DIS | M0)); /*HSUSB0_DIR*/
	MUX_VAL(CP(HSUSB0_NXT),		(IEN  | PTD | DIS | M0)); /*HSUSB0_NXT*/
	MUX_VAL(CP(HSUSB0_DATA0),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA0*/
	MUX_VAL(CP(HSUSB0_DATA1),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA1*/
	MUX_VAL(CP(HSUSB0_DATA2),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA2*/
	MUX_VAL(CP(HSUSB0_DATA3),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA3*/
	MUX_VAL(CP(HSUSB0_DATA4),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA4*/
	MUX_VAL(CP(HSUSB0_DATA5),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA5*/
	MUX_VAL(CP(HSUSB0_DATA6),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA6*/
	MUX_VAL(CP(HSUSB0_DATA7),	(IEN  | PTD | DIS | M0)); /*HSUSB0_DATA7*/

	/* USB EHCI */
	MUX_VAL(CP(ETK_D0_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT0*/
	MUX_VAL(CP(ETK_D1_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT1*/
	MUX_VAL(CP(ETK_D2_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT2*/
	MUX_VAL(CP(ETK_D7_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT3*/
	MUX_VAL(CP(ETK_D4_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT4*/
	MUX_VAL(CP(ETK_D5_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT5*/
	MUX_VAL(CP(ETK_D6_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT6*/
	MUX_VAL(CP(ETK_D3_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT7*/
	MUX_VAL(CP(ETK_D8_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DIR*/
	MUX_VAL(CP(ETK_D9_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_NXT*/
	MUX_VAL(CP(ETK_CTL_ES2),	(IDIS | PTD | DIS | M3)); /*HSUSB1_CLK*/
	MUX_VAL(CP(ETK_CLK_ES2),	(IDIS | PTU | DIS | M3)); /*HSUSB1_STP*/

	MUX_VAL(CP(ETK_D14_ES2),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DT0*/
	MUX_VAL(CP(ETK_D15_ES2),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DT1*/
	MUX_VAL(CP(MCSPI1_CS3),		(IEN  | PTD | EN  | M3)); /*HSUSB2_DT2*/
	MUX_VAL(CP(MCSPI2_CS1),		(IEN  | PTD | EN  | M3)); /*HSUSB2_DT3*/
	MUX_VAL(CP(MCSPI2_SIMO),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DT4*/
	MUX_VAL(CP(MCSPI2_SOMI),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DT5*/
	MUX_VAL(CP(MCSPI2_CS0),		(IEN  | PTD | EN  | M3)); /*HSUSB2_DT6*/
	MUX_VAL(CP(MCSPI2_CLK),		(IEN  | PTD | EN  | M3)); /*HSUSB2_DT7*/
	MUX_VAL(CP(ETK_D12_ES2),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DIR*/
	MUX_VAL(CP(ETK_D13_ES2),	(IEN  | PTD | EN  | M3)); /*HSUSB2_NXT*/
	MUX_VAL(CP(ETK_D10_ES2),	(IDIS | PTD | DIS | M3)); /*HSUSB2_CLK*/
	MUX_VAL(CP(ETK_D11_ES2),	(IDIS | PTU | DIS | M3)); /*HSUSB2_STP*/

	/* SB_T35_USB_HUB_RESET_GPIO */
	MUX_VAL(CP(CAM_WEN),		(IDIS | PTD | DIS | M4)); /*GPIO_167*/

	/* I2C1 */
	MUX_VAL(CP(I2C1_SCL),		(IEN  | PTU | EN  | M0)); /*I2C1_SCL*/
	MUX_VAL(CP(I2C1_SDA),		(IEN  | PTU | EN  | M0)); /*I2C1_SDA*/
	/* I2C2 */
	MUX_VAL(CP(I2C2_SCL),		(IEN  | PTU | EN  | M0)); /*I2C2_SCL*/
	MUX_VAL(CP(I2C2_SDA),		(IEN  | PTU | EN  | M0)); /*I2C2_SDA*/
	/* I2C3 */
	MUX_VAL(CP(I2C3_SCL),		(IEN  | PTU | EN  | M0)); /*I2C3_SCL*/
	MUX_VAL(CP(I2C3_SDA),		(IEN  | PTU | EN  | M0)); /*I2C3_SDA*/

	/* control and debug */
	MUX_VAL(CP(SYS_32K),		(IEN  | PTD | DIS | M0)); /*SYS_32K*/
	MUX_VAL(CP(SYS_CLKREQ),		(IEN  | PTD | DIS | M0)); /*SYS_CLKREQ*/
	MUX_VAL(CP(SYS_NIRQ),		(IEN  | PTU | EN  | M0)); /*SYS_nIRQ*/
	MUX_VAL(CP(SYS_OFF_MODE),	(IEN  | PTD | DIS | M0)); /*OFF_MODE*/
	MUX_VAL(CP(SYS_CLKOUT1),	(IEN  | PTD | DIS | M0)); /*CLKOUT1*/
	MUX_VAL(CP(SYS_CLKOUT2),	(IDIS | PTU | DIS | M4)); /*green LED*/
	MUX_VAL(CP(JTAG_nTRST),		(IEN  | PTD | DIS | M0)); /*JTAG_nTRST*/
	MUX_VAL(CP(JTAG_TCK),		(IEN  | PTD | DIS | M0)); /*JTAG_TCK*/
	MUX_VAL(CP(JTAG_TMS),		(IEN  | PTD | DIS | M0)); /*JTAG_TMS*/
	MUX_VAL(CP(JTAG_TDI),		(IEN  | PTD | DIS | M0)); /*JTAG_TDI*/

	/* MMC1 */
	MUX_VAL(CP(MMC1_CLK),		(IDIS | PTU | EN  | M0)); /*MMC1_CLK*/
	MUX_VAL(CP(MMC1_CMD),		(IEN  | PTU | EN  | M0)); /*MMC1_CMD*/
	MUX_VAL(CP(MMC1_DAT0),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT0*/
	MUX_VAL(CP(MMC1_DAT1),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT1*/
	MUX_VAL(CP(MMC1_DAT2),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT2*/
	MUX_VAL(CP(MMC1_DAT3),		(IEN  | PTU | EN  | M0)); /*MMC1_DAT3*/

	/* SPI */
	MUX_VAL(CP(MCBSP1_CLKR),	(IEN | PTD | DIS | M1)); /*MCSPI4_CLK*/
	MUX_VAL(CP(MCBSP1_DX),		(IEN | PTD | DIS | M1)); /*MCSPI4_SIMO*/
	MUX_VAL(CP(MCBSP1_DR),		(IEN | PTD | DIS | M1)); /*MCSPI4_SOMI*/
	MUX_VAL(CP(MCBSP1_FSX),		(IEN | PTU | EN  | M1)); /*MCSPI4_CS0*/

	/* display controls */
	MUX_VAL(CP(MCBSP1_FSR),		(IDIS | PTU | DIS | M4)); /*GPIO_157*/
}

Beispiel #12

0

Datei anzeigen

Datei: status.c Projekt: pyulchera/gta04-uboot

int status_init(void)
{
	isXM = (get_board_revision() == REVISION_XM);
	i2c_set_bus_num(TWL4030_I2C_BUS);
	if(isXM) {
		/* Set VAUX1 to 3.3V for GTA04E display board */
		twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX1_DEDICATED,
								/*TWL4030_PM_RECEIVER_VAUX1_VSEL_33*/ 0x07,
								TWL4030_PM_RECEIVER_VAUX1_DEV_GRP,
								TWL4030_PM_RECEIVER_DEV_GRP_P1);
		udelay(5000);
	}
#if !defined(CONFIG_OMAP3_GTA04)	// we assume that a GTA04 always has a TCA6507
	if(i2c_set_bus_num(TCA6507_BUS))
		{
		printf ("could not select I2C2\n");
		return 1;
		}
	hasTCA6507 = !i2c_probe(TCA6507_ADDRESS);
#endif
	
	if(!hasTCA6507) {
		if(isXM) { // XM has scrambled dss assignment with respect to default ball names
			MUX_VAL(CP(DSS_DATA18),		(IEN | PTD | EN | M4)); /*GPIO */
			MUX_VAL(CP(DSS_DATA19),		(IEN | PTD | EN | M4)); /*GPIO */
			MUX_VAL(CP(DSS_DATA8),		(IEN | PTD | EN | M4)); /*GPIO */
			MUX_VAL(CP(DSS_DATA9),		(IEN | PTD | EN | M4)); /*GPIO */
			MUX_VAL(CP(SYS_BOOT0),		(IEN | PTD | EN | M4)); /*GPIO */
			MUX_VAL(CP(SYS_BOOT1),		(IEN | PTD | EN | M4)); /*GPIO */
		}
		else {
			MUX_VAL(CP(DSS_DATA0),		(IEN | PTD | EN | M4)); /*GPIO */
			MUX_VAL(CP(DSS_DATA1),		(IEN | PTD | EN | M4)); /*GPIO */
			MUX_VAL(CP(DSS_DATA8),		(IEN | PTD | EN | M4)); /*GPIO */
			MUX_VAL(CP(DSS_DATA9),		(IEN | PTD | EN | M4)); /*GPIO */
			MUX_VAL(CP(DSS_DATA16),		(IEN | PTD | EN | M4)); /*GPIO */
			MUX_VAL(CP(DSS_DATA17),		(IEN | PTD | EN | M4)); /*GPIO */
		}
		
		omap_request_gpio(GPIO_LED_AUX_GREEN);
		omap_request_gpio(GPIO_LED_AUX_RED);
		omap_request_gpio(GPIO_LED_POWER_GREEN);
		omap_request_gpio(GPIO_LED_POWER_RED);
		omap_request_gpio(GPIO_LED_VIBRA);
		omap_request_gpio(GPIO_LED_UNUSED);
		if(GPIO_POWER >= 0)
			omap_request_gpio(GPIO_POWER);
	}
	else {
		// initialize I2C controller
	}
	
	if(GPIO_AUX >= 0)
		omap_request_gpio(GPIO_AUX);
	if(GPIO_POWER >= 0)
		omap_request_gpio(GPIO_POWER);
	if(GPIO_GPSEXT >= 0)
		omap_request_gpio(GPIO_GPSEXT);
	if(GPIO_PENIRQ >= 0)
		omap_request_gpio(GPIO_PENIRQ);
	if(GPIO_KEYIRQ >= 0)
		omap_request_gpio(GPIO_KEYIRQ);
	
	if(!hasTCA6507) {
		omap_set_gpio_direction(GPIO_LED_AUX_GREEN, 0);		// output
		omap_set_gpio_direction(GPIO_LED_AUX_RED, 0);		// output
		omap_set_gpio_direction(GPIO_LED_POWER_GREEN, 0);		// output
		omap_set_gpio_direction(GPIO_LED_POWER_RED, 0);		// output
		omap_set_gpio_direction(GPIO_LED_VIBRA, 0);		// output
		omap_set_gpio_direction(GPIO_LED_UNUSED, 0);		// output
		}
	
	if(GPIO_AUX >= 0)
		omap_set_gpio_direction(GPIO_AUX, 1);		// input
	if(GPIO_POWER >= 0)
		omap_set_gpio_direction(GPIO_POWER, 1);		// input
	if(GPIO_GPSEXT >= 0)
		omap_set_gpio_direction(GPIO_GPSEXT, 1);	// input
	if(GPIO_PENIRQ >= 0)
		omap_set_gpio_direction(GPIO_PENIRQ, 1);	// input
	if(GPIO_KEYIRQ >= 0)
		omap_set_gpio_direction(GPIO_KEYIRQ, 1);	// input

	// when sould we do omap_free_gpio(GPIO_LED_AUX_GREEN); ?
	printf("did init LED driver for %s\n", hasTCA6507?"TCA6507":"GPIOs");

	return 0;
}

Beispiel #13

0

Datei anzeigen

Datei: lowlevel.c Projekt: RobertCNelson/barebox

/**
 * @brief Do the pin muxing required for Board operation.
 * We enable ONLY the pins we require to set. OMAP provides pins which do not
 * have alternate modes. Such pins done need to be set.
 *
 * See @ref MUX_VAL for description of the muxing mode.
 *
 * @return void
 */
static void mux_config(void)
{
	/* SDRC_D0 - SDRC_D31 default mux mode is mode0 */

	/* GPMC */
	MUX_VAL(CP(GPMC_A1), (IDIS | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_A2), (IDIS | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_A3), (IDIS | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_A4), (IDIS | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_A5), (IDIS | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_A6), (IDIS | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_A7), (IDIS | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_A8), (IDIS | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_A9), (IDIS | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_A10), (IDIS | PTD | DIS | M0));

	/* D0-D7 default mux mode is mode0 */
	MUX_VAL(CP(GPMC_D8), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_D9), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_D10), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_D11), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_D12), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_D13), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_D14), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_D15), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_CLK), (IDIS | PTD | DIS | M0));
	/* GPMC_NADV_ALE default mux mode is mode0 */
	/* GPMC_NOE default mux mode is mode0 */
	/* GPMC_NWE default mux mode is mode0 */
	/* GPMC_NBE0_CLE default mux mode is mode0 */
	MUX_VAL(CP(GPMC_NBE0_CLE), (IDIS | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_NBE1), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_NWP), (IEN | PTD | DIS | M0));
	/* GPMC_WAIT0 default mux mode is mode0 */
	MUX_VAL(CP(GPMC_WAIT1), (IEN | PTU | EN | M0));

	/* SERIAL INTERFACE */
	MUX_VAL(CP(UART3_CTS_RCTX), (IEN | PTD | EN | M0));
	MUX_VAL(CP(UART3_RTS_SD), (IDIS | PTD | DIS | M0));
	MUX_VAL(CP(UART3_RX_IRRX), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(UART3_TX_IRTX), (IDIS | PTD | DIS | M0));
	MUX_VAL(CP(HSUSB0_CLK), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(HSUSB0_STP), (IDIS | PTU | EN | M0));
	MUX_VAL(CP(HSUSB0_DIR), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(HSUSB0_NXT), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(HSUSB0_DATA0), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(HSUSB0_DATA1), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(HSUSB0_DATA2), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(HSUSB0_DATA3), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(HSUSB0_DATA4), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(HSUSB0_DATA5), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(HSUSB0_DATA6), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(HSUSB0_DATA7), (IEN | PTD | DIS | M0));
	/* I2C1_SCL default mux mode is mode0 */
	/* I2C1_SDA default mux mode is mode0 */
	/* USB EHCI (port 2) */
	MUX_VAL(CP(MCSPI1_CS3),		(IEN  | PTU | DIS | M3));
	MUX_VAL(CP(MCSPI2_CLK),		(IEN  | PTU | DIS | M3));
	MUX_VAL(CP(MCSPI2_SIMO),	(IEN  | PTU | DIS | M3));
	MUX_VAL(CP(MCSPI2_SOMI),	(IEN  | PTU | DIS | M3));
	MUX_VAL(CP(MCSPI2_CS0),		(IEN  | PTU | DIS | M3));
	MUX_VAL(CP(MCSPI2_CS1),		(IEN  | PTU | DIS | M3));
	MUX_VAL(CP(ETK_D10_ES2),	(IDIS | PTU | DIS | M3));
	MUX_VAL(CP(ETK_D11_ES2),	(IDIS | PTU | DIS | M3));
	MUX_VAL(CP(ETK_D12_ES2),	(IEN  | PTU | DIS | M3));
	MUX_VAL(CP(ETK_D13_ES2),	(IEN  | PTU | DIS | M3));
	MUX_VAL(CP(ETK_D14_ES2),	(IEN  | PTU | DIS | M3));
	MUX_VAL(CP(ETK_D15_ES2),	(IEN  | PTU | DIS | M3));
	MUX_VAL(CP(UART2_RX),		(IEN  | PTD | DIS | M4)) /*GPIO_147*/;
	/* Expansion card */
	MUX_VAL(CP(MMC1_CLK),		(IDIS | PTU | EN  | M0)); /* MMC1_CLK */
	MUX_VAL(CP(MMC1_CMD),		(IEN  | PTU | EN  | M0)); /* MMC1_CMD */
	MUX_VAL(CP(MMC1_DAT0),		(IEN  | PTU | EN  | M0)); /* MMC1_DAT0 */
	MUX_VAL(CP(MMC1_DAT1),		(IEN  | PTU | EN  | M0)); /* MMC1_DAT1 */
	MUX_VAL(CP(MMC1_DAT2),		(IEN  | PTU | EN  | M0)); /* MMC1_DAT2 */
	MUX_VAL(CP(MMC1_DAT3),		(IEN  | PTU | EN  | M0)); /* MMC1_DAT3 */
	MUX_VAL(CP(MMC1_DAT4),		(IEN  | PTU | EN  | M0)); /* MMC1_DAT4 */
	MUX_VAL(CP(MMC1_DAT5),		(IEN  | PTU | EN  | M0)); /* MMC1_DAT5 */
	MUX_VAL(CP(MMC1_DAT6),		(IEN  | PTU | EN  | M0)); /* MMC1_DAT6 */
	MUX_VAL(CP(MMC1_DAT7),		(IEN  | PTU | EN  | M0)); /* MMC1_DAT7 */
}

Beispiel #14

0

Datei anzeigen

Datei: cm_t35.c Projekt: Analias/SNOWLeo-SDR-1

static void cm_t3730_set_muxconf(void)
{
	/* DSS */
	MUX_VAL(CP(DSS_DATA18),		(IDIS | PTD | DIS | M3)); /*DSS_DATA0*/
	MUX_VAL(CP(DSS_DATA19),		(IDIS | PTD | DIS | M3)); /*DSS_DATA1*/
	MUX_VAL(CP(DSS_DATA20),		(IDIS | PTD | DIS | M3)); /*DSS_DATA2*/
	MUX_VAL(CP(DSS_DATA21),		(IDIS | PTD | DIS | M3)); /*DSS_DATA3*/
	MUX_VAL(CP(DSS_DATA22),		(IDIS | PTD | DIS | M3)); /*DSS_DATA4*/
	MUX_VAL(CP(DSS_DATA23),		(IDIS | PTD | DIS | M3)); /*DSS_DATA5*/

	MUX_VAL(CP(SYS_BOOT0),		(IDIS | PTD | DIS | M3)); /*DSS_DATA18*/
	MUX_VAL(CP(SYS_BOOT1),		(IDIS | PTD | DIS | M3)); /*DSS_DATA19*/
	MUX_VAL(CP(SYS_BOOT3),		(IDIS | PTD | DIS | M3)); /*DSS_DATA20*/
	MUX_VAL(CP(SYS_BOOT4),		(IDIS | PTD | DIS | M3)); /*DSS_DATA21*/
	MUX_VAL(CP(SYS_BOOT5),		(IDIS | PTD | DIS | M3)); /*DSS_DATA22*/
	MUX_VAL(CP(SYS_BOOT6),		(IDIS | PTD | DIS | M3)); /*DSS_DATA23*/
}

Beispiel #15

0

Datei anzeigen

Datei: status.c Projekt: OpenPhoenux/gta04-uboot

int status_init(void)
{
	extern int isXM(void);
	i2c_set_bus_num(TWL4030_I2C_BUS);
	thisIsXM = isXM();
	if(thisIsXM) {
		/* Set VAUX1 to 3.3V for GTA04E display board */
		twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX1_DEDICATED,
								/*TWL4030_PM_RECEIVER_VAUX1_VSEL_33*/ 0x07,
								TWL4030_PM_RECEIVER_VAUX1_DEV_GRP,
								TWL4030_PM_RECEIVER_DEV_GRP_P1);
		udelay(5000);
	}

#if CHECK_TCA6507
	if(i2c_set_bus_num(TCA6507_BUS))
		{ // check if we have a tca
		printf ("could not select I2C2 to probe for TCA6507\n");
		return 1;
		}
	hasTCA6507 = !i2c_probe(TCA6507_ADDRESS);
#endif
	
	if(!hasTCA6507) { // reuse DSS pins
		if(thisIsXM) { // XM has scrambled dss assignment with respect to default ball names
			MUX_VAL(CP(DSS_DATA18),		(IEN | PTD | EN | M4)); /*GPIO */
			MUX_VAL(CP(DSS_DATA19),		(IEN | PTD | EN | M4)); /*GPIO */
			MUX_VAL(CP(DSS_DATA8),		(IEN | PTD | EN | M4)); /*GPIO */
			MUX_VAL(CP(DSS_DATA9),		(IEN | PTD | EN | M4)); /*GPIO */
			MUX_VAL(CP(SYS_BOOT0),		(IEN | PTD | EN | M4)); /*GPIO */
			MUX_VAL(CP(SYS_BOOT1),		(IEN | PTD | EN | M4)); /*GPIO */
		}
		else {
			MUX_VAL(CP(DSS_DATA0),		(IEN | PTD | EN | M4)); /*GPIO */
			MUX_VAL(CP(DSS_DATA1),		(IEN | PTD | EN | M4)); /*GPIO */
			MUX_VAL(CP(DSS_DATA8),		(IEN | PTD | EN | M4)); /*GPIO */
			MUX_VAL(CP(DSS_DATA9),		(IEN | PTD | EN | M4)); /*GPIO */
			MUX_VAL(CP(DSS_DATA16),		(IEN | PTD | EN | M4)); /*GPIO */
			MUX_VAL(CP(DSS_DATA17),		(IEN | PTD | EN | M4)); /*GPIO */
		}
		
		gpio_request(GPIO_LED_AUX_GREEN, "green-aux");
		gpio_request(GPIO_LED_AUX_RED, "red-aux");
		gpio_request(GPIO_LED_POWER_GREEN, "green-power");
		gpio_request(GPIO_LED_POWER_RED, "red-power");
		gpio_request(GPIO_LED_VIBRA, "vibra");
		gpio_request(GPIO_LED_UNUSED, "unused");
		if(GPIO_POWER >= 0)
			gpio_request(GPIO_POWER, "power");
	}
	else {
		// initialize I2C controller
	}
	
	if(GPIO_AUX >= 0)
		gpio_request(GPIO_AUX, "aus");
	if(GPIO_POWER >= 0)
		gpio_request(GPIO_POWER, "power");
	if(GPIO_GPSEXT >= 0)
		gpio_request(GPIO_GPSEXT, "ext-gps");
	if(GPIO_PENIRQ >= 0)
		gpio_request(GPIO_PENIRQ, "penirq");
	if(GPIO_KEYIRQ >= 0)
		gpio_request(GPIO_KEYIRQ, "keyirq");
	
	if(!hasTCA6507) {
		gpio_direction_output(GPIO_LED_AUX_GREEN, 0);		// output
		gpio_direction_output(GPIO_LED_AUX_RED, 0);		// output
		gpio_direction_output(GPIO_LED_POWER_GREEN, 0);		// output
		gpio_direction_output(GPIO_LED_POWER_RED, 0);		// output
		gpio_direction_output(GPIO_LED_VIBRA, 0);		// output
		gpio_direction_output(GPIO_LED_UNUSED, 0);		// output
		}
	
	if(GPIO_AUX >= 0)
		gpio_direction_input(GPIO_AUX);		// input
	if(GPIO_POWER >= 0)
		gpio_direction_input(GPIO_POWER);		// input
	if(GPIO_GPSEXT >= 0)
		gpio_direction_input(GPIO_GPSEXT);	// input
	if(GPIO_PENIRQ >= 0)
		gpio_direction_input(GPIO_PENIRQ);	// input
	if(GPIO_KEYIRQ >= 0)
		gpio_direction_input(GPIO_KEYIRQ);	// input

	// when sould we do omap_free_gpio(GPIO_LED_AUX_GREEN); ?
	printf("did init LED driver for %s\n", hasTCA6507?"TCA6507":"GPIOs");

	return 0;
}

Beispiel #16

0

Datei anzeigen

Datei: logic-data.c Projekt: Aircell/asp-u-boot

/* Put SCLK/SDA pins connected to the product ID into GPIO mode */
static void gpio_i2c_config_pins(void)
{
	MUX_VAL(CP(I2C3_SCL),       (IEN  | PTU | EN  | M4)); /*I2C3_SCL*/
	MUX_VAL(CP(I2C3_SDA),       (IEN  | PTU | EN  | M4)); /*I2C3_SDA*/
}

Beispiel #17

0

Datei anzeigen

Datei: lowlevel.c Projekt: AubrCool/barebox

/**
 * @brief Do the pin muxing required for Board operation.
 *
 * See @ref MUX_VAL for description of the muxing mode. Since some versions
 * of Linux depend on all pin muxing being done at barebox level, we may need to
 * enable CONFIG_MACH_OMAP_ADVANCED_MUX to enable the full fledged pin muxing.
 *
 * @return void
 */
static void mux_config(void)
{
	/* Essential MUX Settings */
	MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0));	/* SDRC_D0 */
	MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0));	/* SDRC_D1 */
	MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0));	/* SDRC_D2 */
	MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0));	/* SDRC_D3 */
	MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0));	/* SDRC_D4 */
	MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0));	/* SDRC_D5 */
	MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0));	/* SDRC_D6 */
	MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0));	/* SDRC_D7 */
	MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0));	/* SDRC_D8 */
	MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0));	/* SDRC_D9 */
	MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0));	/* SDRC_D10 */
	MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0));	/* SDRC_D11 */
	MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0));	/* SDRC_D12 */
	MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0));	/* SDRC_D13 */
	MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0));	/* SDRC_D14 */
	MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0));	/* SDRC_D15 */
	MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0));	/* SDRC_D16 */
	MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0));	/* SDRC_D17 */
	MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0));	/* SDRC_D18 */
	MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0));	/* SDRC_D19 */
	MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0));	/* SDRC_D20 */
	MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0));	/* SDRC_D21 */
	MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0));	/* SDRC_D22 */
	MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0));	/* SDRC_D23 */
	MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0));	/* SDRC_D24 */
	MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0));	/* SDRC_D25 */
	MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0));	/* SDRC_D26 */
	MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0));	/* SDRC_D27 */
	MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0));	/* SDRC_D28 */
	MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0));	/* SDRC_D29 */
	MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0));	/* SDRC_D30 */
	MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0));	/* SDRC_D31 */
	MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0));	/* SDRC_CLK */
	MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0));	/* SDRC_DQS0 */
	MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0));	/* SDRC_DQS1 */
	MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0));	/* SDRC_DQS2 */
	MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0));	/* SDRC_DQS3 */
	/* GPMC */
	MUX_VAL(CP(GPMC_A1), (IDIS | PTD | DIS | M0));	/* GPMC_A1 */
	MUX_VAL(CP(GPMC_A2), (IDIS | PTD | DIS | M0));	/* GPMC_A2 */
	MUX_VAL(CP(GPMC_A3), (IDIS | PTD | DIS | M0));	/* GPMC_A3 */
	MUX_VAL(CP(GPMC_A4), (IDIS | PTD | DIS | M0));	/* GPMC_A4 */
	MUX_VAL(CP(GPMC_A5), (IDIS | PTD | DIS | M0));	/* GPMC_A5 */
	MUX_VAL(CP(GPMC_A6), (IDIS | PTD | DIS | M0));	/* GPMC_A6 */
	MUX_VAL(CP(GPMC_A7), (IDIS | PTD | DIS | M0));	/* GPMC_A7 */
	MUX_VAL(CP(GPMC_A8), (IDIS | PTD | DIS | M0));	/* GPMC_A8 */
	MUX_VAL(CP(GPMC_A9), (IDIS | PTD | DIS | M0));	/* GPMC_A9 */
	MUX_VAL(CP(GPMC_A10), (IDIS | PTD | DIS | M0));	/* GPMC_A10 */
	MUX_VAL(CP(GPMC_D0), (IEN | PTD | DIS | M0));	/* GPMC_D0 */
	MUX_VAL(CP(GPMC_D1), (IEN | PTD | DIS | M0));	/* GPMC_D1 */
	MUX_VAL(CP(GPMC_D2), (IEN | PTD | DIS | M0));	/* GPMC_D2 */
	MUX_VAL(CP(GPMC_D3), (IEN | PTD | DIS | M0));	/* GPMC_D3 */
	MUX_VAL(CP(GPMC_D4), (IEN | PTD | DIS | M0));	/* GPMC_D4 */
	MUX_VAL(CP(GPMC_D5), (IEN | PTD | DIS | M0));	/* GPMC_D5 */
	MUX_VAL(CP(GPMC_D6), (IEN | PTD | DIS | M0));	/* GPMC_D6 */
	MUX_VAL(CP(GPMC_D7), (IEN | PTD | DIS | M0));	/* GPMC_D7 */
	MUX_VAL(CP(GPMC_D8), (IEN | PTD | DIS | M0));	/* GPMC_D8 */
	MUX_VAL(CP(GPMC_D9), (IEN | PTD | DIS | M0));	/* GPMC_D9 */
	MUX_VAL(CP(GPMC_D10), (IEN | PTD | DIS | M0));	/* GPMC_D10 */
	MUX_VAL(CP(GPMC_D11), (IEN | PTD | DIS | M0));	/* GPMC_D11 */
	MUX_VAL(CP(GPMC_D12), (IEN | PTD | DIS | M0));	/* GPMC_D12 */
	MUX_VAL(CP(GPMC_D13), (IEN | PTD | DIS | M0));	/* GPMC_D13 */
	MUX_VAL(CP(GPMC_D14), (IEN | PTD | DIS | M0));	/* GPMC_D14 */
	MUX_VAL(CP(GPMC_D15), (IEN | PTD | DIS | M0));	/* GPMC_D15 */
	MUX_VAL(CP(GPMC_NCS0), (IDIS | PTU | EN | M0));	/* GPMC_NCS0 */
	MUX_VAL(CP(GPMC_NCS1), (IDIS | PTU | EN | M0));	/* GPMC_NCS1 */
	MUX_VAL(CP(GPMC_NCS2), (IDIS | PTU | EN | M0));	/* GPMC_NCS2 */
	MUX_VAL(CP(GPMC_NCS3), (IDIS | PTU | EN | M0));	/* GPMC_NCS3 */
	/* GPIO_55 - FLASH_DIS */
	MUX_VAL(CP(GPMC_NCS4), (IEN | PTU | EN | M4));
	/* GPIO_56 - TORCH_EN */
	MUX_VAL(CP(GPMC_NCS5), (IDIS | PTD | DIS | M4));
	/* GPIO_57 - AGPS SLP */
	MUX_VAL(CP(GPMC_NCS6), (IEN | PTD | DIS | M4));
	/* GPMC_58 - WLAN_IRQ */
	MUX_VAL(CP(GPMC_NCS7), (IEN | PTU | EN | M4));
	MUX_VAL(CP(GPMC_CLK), (IDIS | PTD | DIS | M0));	/* GPMC_CLK */
	/* GPMC_NADV_ALE */
	MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0));	/* GPMC_NOE */
	MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0));	/* GPMC_NWE */
	/* GPMC_NBE0_CLE */
	MUX_VAL(CP(GPMC_NBE0_CLE), (IDIS | PTD | DIS | M0));
	MUX_VAL(CP(GPMC_NBE1), (IEN | PTD | DIS | M4));	/* GPIO_61 -BT_SHUTDN */
	MUX_VAL(CP(GPMC_NWP), (IEN | PTD | DIS | M0));	/* GPMC_NWP */
	MUX_VAL(CP(GPMC_WAIT0), (IEN | PTU | EN | M0));	/* GPMC_WAIT0 */
	MUX_VAL(CP(GPMC_WAIT1), (IEN | PTU | EN | M0));	/* GPMC_WAIT1 */
	MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | EN | M4));	/* GPIO_64 */
	MUX_VAL(CP(GPMC_WAIT3), (IEN | PTU | EN | M4));	/* GPIO_65 */

	/* SERIAL INTERFACE */
	/* UART3_CTS_RCTX */
	MUX_VAL(CP(UART3_CTS_RCTX), (IEN | PTD | EN | M0));
	/* UART3_RTS_SD */
	MUX_VAL(CP(UART3_RTS_SD), (IDIS | PTD | DIS | M0));
	/* UART3_RX_IRRX */
	MUX_VAL(CP(UART3_RX_IRRX), (IEN | PTD | DIS | M0));
	/* UART3_TX_IRTX */
	MUX_VAL(CP(UART3_TX_IRTX), (IDIS | PTD | DIS | M0));
	/* HSUSB0_CLK */
	MUX_VAL(CP(HSUSB0_CLK), (IEN | PTD | DIS | M0));
	/* HSUSB0_STP */
	MUX_VAL(CP(HSUSB0_STP), (IDIS | PTU | EN | M0));
	/* HSUSB0_DIR */
	MUX_VAL(CP(HSUSB0_DIR), (IEN | PTD | DIS | M0));
	/* HSUSB0_NXT */
	MUX_VAL(CP(HSUSB0_NXT), (IEN | PTD | DIS | M0));
	/* HSUSB0_DATA0 */
	MUX_VAL(CP(HSUSB0_DATA0), (IEN | PTD | DIS | M0));
	/* HSUSB0_DATA1 */
	MUX_VAL(CP(HSUSB0_DATA1), (IEN | PTD | DIS | M0));
	/* HSUSB0_DATA2 */
	MUX_VAL(CP(HSUSB0_DATA2), (IEN | PTD | DIS | M0));
	/* HSUSB0_DATA3 */
	MUX_VAL(CP(HSUSB0_DATA3), (IEN | PTD | DIS | M0));
	/* HSUSB0_DATA4 */
	MUX_VAL(CP(HSUSB0_DATA4), (IEN | PTD | DIS | M0));
	/* HSUSB0_DATA5 */
	MUX_VAL(CP(HSUSB0_DATA5), (IEN | PTD | DIS | M0));
	/* HSUSB0_DATA6 */
	MUX_VAL(CP(HSUSB0_DATA6), (IEN | PTD | DIS | M0));
	/* HSUSB0_DATA7 */
	MUX_VAL(CP(HSUSB0_DATA7), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(I2C1_SCL), (IEN | PTU | EN | M0));	/* I2C1_SCL */
	MUX_VAL(CP(I2C1_SDA), (IEN | PTU | EN | M0));	/* I2C1_SDA */
#ifdef CONFIG_MACH_OMAP_ADVANCED_MUX
	/* DSS */
	MUX_VAL(CP(DSS_PCLK), (IDIS | PTD | DIS | M0));	/* DSS_PCLK */
	MUX_VAL(CP(DSS_HSYNC), (IDIS | PTD | DIS | M0));	/* DSS_HSYNC */
	MUX_VAL(CP(DSS_VSYNC), (IDIS | PTD | DIS | M0));	/* DSS_VSYNC */
	MUX_VAL(CP(DSS_ACBIAS), (IDIS | PTD | DIS | M0));	/* DSS_ACBIAS */
	MUX_VAL(CP(DSS_DATA0), (IDIS | PTD | DIS | M0));	/* DSS_DATA0 */
	MUX_VAL(CP(DSS_DATA1), (IDIS | PTD | DIS | M0));	/* DSS_DATA1 */
	MUX_VAL(CP(DSS_DATA2), (IDIS | PTD | DIS | M0));	/* DSS_DATA2 */
	MUX_VAL(CP(DSS_DATA3), (IDIS | PTD | DIS | M0));	/* DSS_DATA3 */
	MUX_VAL(CP(DSS_DATA4), (IDIS | PTD | DIS | M0));	/* DSS_DATA4 */
	MUX_VAL(CP(DSS_DATA5), (IDIS | PTD | DIS | M0));	/* DSS_DATA5 */
	MUX_VAL(CP(DSS_DATA6), (IDIS | PTD | DIS | M0));	/* DSS_DATA6 */
	MUX_VAL(CP(DSS_DATA7), (IDIS | PTD | DIS | M0));	/* DSS_DATA7 */
	MUX_VAL(CP(DSS_DATA8), (IDIS | PTD | DIS | M0));	/* DSS_DATA8 */
	MUX_VAL(CP(DSS_DATA9), (IDIS | PTD | DIS | M0));	/* DSS_DATA9 */
	MUX_VAL(CP(DSS_DATA10), (IDIS | PTD | DIS | M0));	/* DSS_DATA10 */
	MUX_VAL(CP(DSS_DATA11), (IDIS | PTD | DIS | M0));	/* DSS_DATA11 */
	MUX_VAL(CP(DSS_DATA12), (IDIS | PTD | DIS | M0));	/* DSS_DATA12 */
	MUX_VAL(CP(DSS_DATA13), (IDIS | PTD | DIS | M0));	/* DSS_DATA13 */
	MUX_VAL(CP(DSS_DATA14), (IDIS | PTD | DIS | M0));	/* DSS_DATA14 */
	MUX_VAL(CP(DSS_DATA15), (IDIS | PTD | DIS | M0));	/* DSS_DATA15 */
	MUX_VAL(CP(DSS_DATA16), (IDIS | PTD | DIS | M0));	/* DSS_DATA16 */
	MUX_VAL(CP(DSS_DATA17), (IDIS | PTD | DIS | M0));	/* DSS_DATA17 */
	MUX_VAL(CP(DSS_DATA18), (IDIS | PTD | DIS | M0));	/* DSS_DATA18 */
	MUX_VAL(CP(DSS_DATA19), (IDIS | PTD | DIS | M0));	/* DSS_DATA19 */
	MUX_VAL(CP(DSS_DATA20), (IDIS | PTD | DIS | M0));	/* DSS_DATA20 */
	MUX_VAL(CP(DSS_DATA21), (IDIS | PTD | DIS | M0));	/* DSS_DATA21 */
	MUX_VAL(CP(DSS_DATA22), (IDIS | PTD | DIS | M0));	/* DSS_DATA22 */
	MUX_VAL(CP(DSS_DATA23), (IDIS | PTD | DIS | M0));	/* DSS_DATA23 */
	/* CAMERA */
	MUX_VAL(CP(CAM_HS), (IEN | PTU | EN | M0));	/* CAM_HS */
	MUX_VAL(CP(CAM_VS), (IEN | PTU | EN | M0));	/* CAM_VS */
	MUX_VAL(CP(CAM_XCLKA), (IDIS | PTD | DIS | M0));	/* CAM_XCLKA */
	MUX_VAL(CP(CAM_PCLK), (IEN | PTU | EN | M0));	/* CAM_PCLK */
	/* GPIO_98 - CAM_RESET */
	MUX_VAL(CP(CAM_FLD), (IDIS | PTD | DIS | M4));
	MUX_VAL(CP(CAM_D0), (IEN | PTD | DIS | M0));	/* CAM_D0 */
	MUX_VAL(CP(CAM_D1), (IEN | PTD | DIS | M0));	/* CAM_D1 */
	MUX_VAL(CP(CAM_D2), (IEN | PTD | DIS | M0));	/* CAM_D2 */
	MUX_VAL(CP(CAM_D3), (IEN | PTD | DIS | M0));	/* CAM_D3 */
	MUX_VAL(CP(CAM_D4), (IEN | PTD | DIS | M0));	/* CAM_D4 */
	MUX_VAL(CP(CAM_D5), (IEN | PTD | DIS | M0));	/* CAM_D5 */
	MUX_VAL(CP(CAM_D6), (IEN | PTD | DIS | M0));	/* CAM_D6 */
	MUX_VAL(CP(CAM_D7), (IEN | PTD | DIS | M0));	/* CAM_D7 */
	MUX_VAL(CP(CAM_D8), (IEN | PTD | DIS | M0));	/* CAM_D8 */
	MUX_VAL(CP(CAM_D9), (IEN | PTD | DIS | M0));	/* CAM_D9 */
	MUX_VAL(CP(CAM_D10), (IEN | PTD | DIS | M0));	/* CAM_D10 */
	MUX_VAL(CP(CAM_D11), (IEN | PTD | DIS | M0));	/* CAM_D11 */
	MUX_VAL(CP(CAM_XCLKB), (IDIS | PTD | DIS | M0));	/* CAM_XCLKB */
	MUX_VAL(CP(CAM_WEN), (IEN | PTD | DIS | M4));	/* GPIO_167 */
	MUX_VAL(CP(CAM_STROBE), (IDIS | PTD | DIS | M0));	/* CAM_STROBE */
	MUX_VAL(CP(CSI2_DX0), (IEN | PTD | DIS | M0));	/* CSI2_DX0 */
	MUX_VAL(CP(CSI2_DY0), (IEN | PTD | DIS | M0));	/* CSI2_DY0 */
	MUX_VAL(CP(CSI2_DX1), (IEN | PTD | DIS | M0));	/* CSI2_DX1 */
	MUX_VAL(CP(CSI2_DY1), (IEN | PTD | DIS | M0));	/* CSI2_DY1 */
	/* AUDIO INTERFACE */
	MUX_VAL(CP(MCBSP2_FSX), (IEN | PTD | DIS | M0));	/* MCBSP2_FSX */
	/* MCBSP2_CLKX */
	MUX_VAL(CP(MCBSP2_CLKX), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(MCBSP2_DR), (IEN | PTD | DIS | M0));	/* MCBSP2_DR */
	MUX_VAL(CP(MCBSP2_DX), (IDIS | PTD | DIS | M0));	/* MCBSP2_DX */
	/* EXPANSION CARD  */
	MUX_VAL(CP(MMC1_CLK), (IDIS | PTU | EN | M0));	/* MMC1_CLK */
	MUX_VAL(CP(MMC1_CMD), (IEN | PTU | EN | M0));	/* MMC1_CMD */
	MUX_VAL(CP(MMC1_DAT0), (IEN | PTU | EN | M0));	/* MMC1_DAT0 */
	MUX_VAL(CP(MMC1_DAT1), (IEN | PTU | EN | M0));	/* MMC1_DAT1 */
	MUX_VAL(CP(MMC1_DAT2), (IEN | PTU | EN | M0));	/* MMC1_DAT2 */
	MUX_VAL(CP(MMC1_DAT3), (IEN | PTU | EN | M0));	/* MMC1_DAT3 */
	MUX_VAL(CP(MMC1_DAT4), (IEN | PTU | EN | M0));	/* MMC1_DAT4 */
	MUX_VAL(CP(MMC1_DAT5), (IEN | PTU | EN | M0));	/* MMC1_DAT5 */
	MUX_VAL(CP(MMC1_DAT6), (IEN | PTU | EN | M0));	/* MMC1_DAT6 */
	MUX_VAL(CP(MMC1_DAT7), (IEN | PTU | EN | M0));	/* MMC1_DAT7 */
	/* WIRELESS LAN */
	MUX_VAL(CP(MMC2_CLK), (IEN | PTD | DIS | M0));	/* MMC2_CLK */
	MUX_VAL(CP(MMC2_CMD), (IEN | PTU | EN | M0));	/* MMC2_CMD */
	MUX_VAL(CP(MMC2_DAT0), (IEN | PTU | EN | M0));	/* MMC2_DAT0 */
	MUX_VAL(CP(MMC2_DAT1), (IEN | PTU | EN | M0));	/* MMC2_DAT1 */
	MUX_VAL(CP(MMC2_DAT2), (IEN | PTU | EN | M0));	/* MMC2_DAT2 */
	MUX_VAL(CP(MMC2_DAT3), (IEN | PTU | EN | M0));	/* MMC2_DAT3 */
	/* MMC2_DIR_DAT0 */
	MUX_VAL(CP(MMC2_DAT4), (IDIS | PTD | DIS | M1));
	/* MMC2_DIR_DAT1 */
	MUX_VAL(CP(MMC2_DAT5), (IDIS | PTD | DIS | M1));
	/* MMC2_DIR_CMD */
	MUX_VAL(CP(MMC2_DAT6), (IDIS | PTD | DIS | M1));
	/* MMC2_CLKIN */
	MUX_VAL(CP(MMC2_DAT7), (IEN | PTU | EN | M1));
	/* BLUETOOTH */
	/* MCBSP3_DX */
	MUX_VAL(CP(MCBSP3_DX), (IDIS | PTD | DIS | M0));
	/* MCBSP3_DR */
	MUX_VAL(CP(MCBSP3_DR), (IEN | PTD | DIS | M0));
	/* MCBSP3_CLKX */
	MUX_VAL(CP(MCBSP3_CLKX), (IEN | PTD | DIS | M0));
	/* MCBSP3_FSX */
	MUX_VAL(CP(MCBSP3_FSX), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(UART2_CTS), (IEN | PTU | EN | M0));	/* UART2_CTS */
	MUX_VAL(CP(UART2_RTS), (IDIS | PTD | DIS | M0));	/* UART2_RTS */
	MUX_VAL(CP(UART2_TX), (IDIS | PTD | DIS | M0));	/* UART2_TX */
	MUX_VAL(CP(UART2_RX), (IEN | PTD | DIS | M0));	/* UART2_RX */
	/* MODEM INTERFACE */
	MUX_VAL(CP(UART1_TX), (IDIS | PTD | DIS | M0));	/* UART1_TX */
	MUX_VAL(CP(UART1_RTS), (IDIS | PTD | DIS | M0));	/* UART1_RTS */
	MUX_VAL(CP(UART1_CTS), (IEN | PTU | DIS | M0));	/* UART1_CTS */
	MUX_VAL(CP(UART1_RX), (IEN | PTD | DIS | M0));	/* UART1_RX */
	/* SSI1_DAT_RX */
	MUX_VAL(CP(MCBSP4_CLKX), (IEN | PTD | DIS | M1));
	MUX_VAL(CP(MCBSP4_DR), (IEN | PTD | DIS | M1));	/* SSI1_FLAG_RX */
	MUX_VAL(CP(MCBSP4_DX), (IEN | PTD | DIS | M1));	/* SSI1_RDY_RX  */
	MUX_VAL(CP(MCBSP4_FSX), (IEN | PTD | DIS | M1));	/* SSI1_WAKE */
	/* MCBSP1_CLKR  */
	MUX_VAL(CP(MCBSP1_CLKR), (IEN | PTD | DIS | M0));
	/* GPIO_157 - BT_WKUP */
	MUX_VAL(CP(MCBSP1_FSR), (IDIS | PTU | EN | M4));
	/* MCBSP1_DX */
	MUX_VAL(CP(MCBSP1_DX), (IDIS | PTD | DIS | M0));
	MUX_VAL(CP(MCBSP1_DR), (IEN | PTD | DIS | M0));	/* MCBSP1_DR */
	/* MCBSP_CLKS  */
	MUX_VAL(CP(MCBSP_CLKS), (IEN | PTU | DIS | M0));
	/* MCBSP1_FSX */
	MUX_VAL(CP(MCBSP1_FSX), (IEN | PTD | DIS | M0));
	/* MCBSP1_CLKX  */
	MUX_VAL(CP(MCBSP1_CLKX), (IEN | PTD | DIS | M0));
	/* SERIAL INTERFACE */
	MUX_VAL(CP(I2C2_SCL), (IEN | PTU | EN | M0));	/* I2C2_SCL */
	MUX_VAL(CP(I2C2_SDA), (IEN | PTU | EN | M0));	/* I2C2_SDA */
	MUX_VAL(CP(I2C3_SCL), (IEN | PTU | EN | M0));	/* I2C3_SCL */
	MUX_VAL(CP(I2C3_SDA), (IEN | PTU | EN | M0));	/* I2C3_SDA */
	MUX_VAL(CP(I2C4_SCL), (IEN | PTU | EN | M0));	/* I2C4_SCL */
	MUX_VAL(CP(I2C4_SDA), (IEN | PTU | EN | M0));	/* I2C4_SDA */
	MUX_VAL(CP(HDQ_SIO), (IEN | PTU | EN | M0));	/* HDQ_SIO */
	/* MCSPI1_CLK */
	MUX_VAL(CP(MCSPI1_CLK), (IEN | PTD | DIS | M0));
	/* MCSPI1_SIMO */
	MUX_VAL(CP(MCSPI1_SIMO), (IEN | PTD | DIS | M0));
	/* MCSPI1_SOMI */
	MUX_VAL(CP(MCSPI1_SOMI), (IEN | PTD | DIS | M0));
	/* MCSPI1_CS0 */
	MUX_VAL(CP(MCSPI1_CS0), (IEN | PTD | EN | M0));
	/* MCSPI1_CS1 */
	MUX_VAL(CP(MCSPI1_CS1), (IDIS | PTD | EN | M0));
	/* GPIO_176-NOR_DPD */
	MUX_VAL(CP(MCSPI1_CS2), (IDIS | PTD | DIS | M4));
	/* MCSPI1_CS3 */
	MUX_VAL(CP(MCSPI1_CS3), (IEN | PTD | EN | M0));
	/* MCSPI2_CLK */
	MUX_VAL(CP(MCSPI2_CLK), (IEN | PTD | DIS | M0));
	/* MCSPI2_SIMO */
	MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTD | DIS | M0));
	/* MCSPI2_SOMI */
	MUX_VAL(CP(MCSPI2_SOMI), (IEN | PTD | DIS | M0));
	/* MCSPI2_CS0 */
	MUX_VAL(CP(MCSPI2_CS0), (IEN | PTD | EN | M0));
	/* MCSPI2_CS1 */
	MUX_VAL(CP(MCSPI2_CS1), (IEN | PTD | EN | M0));

	/* CONTROL AND DEBUG */
	MUX_VAL(CP(SYS_32K), (IEN | PTD | DIS | M0));	/* SYS_32K */
	MUX_VAL(CP(SYS_CLKREQ), (IEN | PTD | DIS | M0));	/* SYS_CLKREQ */
	MUX_VAL(CP(SYS_NIRQ), (IEN | PTU | EN | M0));	/* SYS_NIRQ */
	MUX_VAL(CP(SYS_BOOT0), (IEN | PTD | DIS | M4));	/* GPIO_2 - PEN_IRQ */
	MUX_VAL(CP(SYS_BOOT1), (IEN | PTD | DIS | M4));	/* GPIO_3 */
	MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M4));	/* GPIO_4 - MMC1_WP */
	MUX_VAL(CP(SYS_BOOT3), (IEN | PTD | DIS | M4));	/* GPIO_5 - LCD_ENVDD */
	MUX_VAL(CP(SYS_BOOT4), (IEN | PTD | DIS | M4));	/* GPIO_6 - LAN_INTR0 */
	MUX_VAL(CP(SYS_BOOT5), (IEN | PTD | DIS | M4));	/* GPIO_7 - MMC2_WP */
	/* GPIO_8-LCD_ENBKL */
	MUX_VAL(CP(SYS_BOOT6), (IDIS | PTD | DIS | M4));
	/* SYS_OFF_MODE */
	MUX_VAL(CP(SYS_OFF_MODE), (IEN | PTD | DIS | M0));
	/* SYS_CLKOUT1  */
	MUX_VAL(CP(SYS_CLKOUT1), (IEN | PTD | DIS | M0));
	MUX_VAL(CP(SYS_CLKOUT2), (IEN | PTU | EN | M4));	/* GPIO_186 */
	MUX_VAL(CP(JTAG_NTRST), (IEN | PTD | DIS | M0));	/* JTAG_NTRST */
	MUX_VAL(CP(JTAG_TCK), (IEN | PTD | DIS | M0));	/* JTAG_TCK */
	MUX_VAL(CP(JTAG_TMS), (IEN | PTD | DIS | M0));	/* JTAG_TMS */
	MUX_VAL(CP(JTAG_TDI), (IEN | PTD | DIS | M0));	/* JTAG_TDI */
	MUX_VAL(CP(JTAG_EMU0), (IEN | PTD | DIS | M0));	/* JTAG_EMU0 */
	MUX_VAL(CP(JTAG_EMU1), (IEN | PTD | DIS | M0));	/* JTAG_EMU1 */
	/* HSUSB1_TLL_STP */
	MUX_VAL(CP(ETK_CLK_ES2), (IDIS | PTU | EN | M0));
	/* HSUSB1_TLL_CLK */
	MUX_VAL(CP(ETK_CTL_ES2), (IDIS | PTD | DIS | M0));
	/* HSUSB1_TLL_DATA0 */
	MUX_VAL(CP(ETK_D0_ES2), (IEN | PTD | DIS | M1));
	/* MCSPI3_CS0 */
	MUX_VAL(CP(ETK_D1_ES2), (IEN | PTD | DIS | M1));
	/* HSUSB1_TLL_DATA2 */
	MUX_VAL(CP(ETK_D2_ES2), (IEN | PTD | EN | M1));
	/* HSUSB1_TLL_DATA7 */
	MUX_VAL(CP(ETK_D3_ES2), (IEN | PTD | DIS | M1));
	/* HSUSB1_TLL_DATA4 */
	MUX_VAL(CP(ETK_D4_ES2), (IEN | PTD | DIS | M0));
	/* HSUSB1_TLL_DATA5 */
	MUX_VAL(CP(ETK_D5_ES2), (IEN | PTD | DIS | M0));
	/* HSUSB1_TLL_DATA6 */
	MUX_VAL(CP(ETK_D6_ES2), (IEN | PTD | DIS | M0));
	/* HSUSB1_TLL_DATA3 */
	MUX_VAL(CP(ETK_D7_ES2), (IEN | PTD | DIS | M0));
	/* HSUSB1_TLL_DIR */
	MUX_VAL(CP(ETK_D8_ES2), (IEN | PTD | DIS | M0));
	/* HSUSB1_TLL_NXT */
	MUX_VAL(CP(ETK_D9_ES2), (IEN | PTD | DIS | M0));
	/* HSUSB2_TLL_CLK */
	MUX_VAL(CP(ETK_D10_ES2), (IEN | PTD | DIS | M0));
	/* HSUSB2_TLL_STP */
	MUX_VAL(CP(ETK_D11_ES2), (IEN | PTD | DIS | M0));
	/* HSUSB2_TLL_DIR */
	MUX_VAL(CP(ETK_D12_ES2), (IEN | PTD | DIS | M0));
	/* HSUSB2_TLL_NXT */
	MUX_VAL(CP(ETK_D13_ES2), (IEN | PTD | DIS | M0));
	/* HSUSB2_TLL_DATA0 */
	MUX_VAL(CP(ETK_D14_ES2), (IEN | PTD | DIS | M0));
	/* HSUSB2_TLL_DATA1 */
	MUX_VAL(CP(ETK_D15_ES2), (IEN | PTD | DIS | M0));

	/* DIE TO DIE */
	MUX_VAL(CP(D2D_MCAD0), (IEN | PTD | EN | M0));	/* D2D_MCAD0 */
	MUX_VAL(CP(D2D_MCAD1), (IEN | PTD | EN | M0));	/* D2D_MCAD1 */
	MUX_VAL(CP(D2D_MCAD2), (IEN | PTD | EN | M0));	/* D2D_MCAD2 */
	MUX_VAL(CP(D2D_MCAD3), (IEN | PTD | EN | M0));	/* D2D_MCAD3 */
	MUX_VAL(CP(D2D_MCAD4), (IEN | PTD | EN | M0));	/* D2D_MCAD4 */
	MUX_VAL(CP(D2D_MCAD5), (IEN | PTD | EN | M0));	/* D2D_MCAD5 */
	MUX_VAL(CP(D2D_MCAD6), (IEN | PTD | EN | M0));	/* D2D_MCAD6 */
	MUX_VAL(CP(D2D_MCAD7), (IEN | PTD | EN | M0));	/* D2D_MCAD7 */
	MUX_VAL(CP(D2D_MCAD8), (IEN | PTD | EN | M0));	/* D2D_MCAD8 */
	MUX_VAL(CP(D2D_MCAD9), (IEN | PTD | EN | M0));	/* D2D_MCAD9 */
	MUX_VAL(CP(D2D_MCAD10), (IEN | PTD | EN | M0));	/* D2D_MCAD10 */
	MUX_VAL(CP(D2D_MCAD11), (IEN | PTD | EN | M0));	/* D2D_MCAD11 */
	MUX_VAL(CP(D2D_MCAD12), (IEN | PTD | EN | M0));	/* D2D_MCAD12 */
	MUX_VAL(CP(D2D_MCAD13), (IEN | PTD | EN | M0));	/* D2D_MCAD13 */
	MUX_VAL(CP(D2D_MCAD14), (IEN | PTD | EN | M0));	/* D2D_MCAD14 */
	MUX_VAL(CP(D2D_MCAD15), (IEN | PTD | EN | M0));	/* D2D_MCAD15 */
	MUX_VAL(CP(D2D_MCAD16), (IEN | PTD | EN | M0));	/* D2D_MCAD16 */
	MUX_VAL(CP(D2D_MCAD17), (IEN | PTD | EN | M0));	/* D2D_MCAD17 */
	MUX_VAL(CP(D2D_MCAD18), (IEN | PTD | EN | M0));	/* D2D_MCAD18 */
	MUX_VAL(CP(D2D_MCAD19), (IEN | PTD | EN | M0));	/* D2D_MCAD19 */
	MUX_VAL(CP(D2D_MCAD20), (IEN | PTD | EN | M0));	/* D2D_MCAD20 */
	MUX_VAL(CP(D2D_MCAD21), (IEN | PTD | EN | M0));	/* D2D_MCAD21 */
	MUX_VAL(CP(D2D_MCAD22), (IEN | PTD | EN | M0));	/* D2D_MCAD22 */
	MUX_VAL(CP(D2D_MCAD23), (IEN | PTD | EN | M0));	/* D2D_MCAD23 */
	MUX_VAL(CP(D2D_MCAD24), (IEN | PTD | EN | M0));	/* D2D_MCAD24 */
	MUX_VAL(CP(D2D_MCAD25), (IEN | PTD | EN | M0));	/* D2D_MCAD25 */
	MUX_VAL(CP(D2D_MCAD26), (IEN | PTD | EN | M0));	/* D2D_MCAD26 */
	MUX_VAL(CP(D2D_MCAD27), (IEN | PTD | EN | M0));	/* D2D_MCAD27 */
	MUX_VAL(CP(D2D_MCAD28), (IEN | PTD | EN | M0));	/* D2D_MCAD28 */
	MUX_VAL(CP(D2D_MCAD29), (IEN | PTD | EN | M0));	/* D2D_MCAD29 */
	MUX_VAL(CP(D2D_MCAD30), (IEN | PTD | EN | M0));	/* D2D_MCAD30 */
	MUX_VAL(CP(D2D_MCAD31), (IEN | PTD | EN | M0));	/* D2D_MCAD31 */
	MUX_VAL(CP(D2D_MCAD32), (IEN | PTD | EN | M0));	/* D2D_MCAD32 */
	MUX_VAL(CP(D2D_MCAD33), (IEN | PTD | EN | M0));	/* D2D_MCAD33 */
	MUX_VAL(CP(D2D_MCAD34), (IEN | PTD | EN | M0));	/* D2D_MCAD34 */
	MUX_VAL(CP(D2D_MCAD35), (IEN | PTD | EN | M0));	/* D2D_MCAD35 */
	MUX_VAL(CP(D2D_MCAD36), (IEN | PTD | EN | M0));	/* D2D_MCAD36 */
	/* D2D_CLK26MI  */
	MUX_VAL(CP(D2D_CLK26MI), (IEN | PTD | DIS | M0));
	/* D2D_NRESPWRON */
	MUX_VAL(CP(D2D_NRESPWRON), (IEN | PTD | EN | M0));
	/* D2D_NRESWARM */
	MUX_VAL(CP(D2D_NRESWARM), (IEN | PTU | EN | M0));
	/* D2D_ARM9NIRQ */
	MUX_VAL(CP(D2D_ARM9NIRQ), (IEN | PTD | DIS | M0));
	/* D2D_UMA2P6FIQ */
	MUX_VAL(CP(D2D_UMA2P6FIQ), (IEN | PTD | DIS | M0));
	/* D2D_SPINT */
	MUX_VAL(CP(D2D_SPINT), (IEN | PTD | EN | M0));
	/* D2D_FRINT */
	MUX_VAL(CP(D2D_FRINT), (IEN | PTD | EN | M0));
	/* D2D_DMAREQ0  */
	MUX_VAL(CP(D2D_DMAREQ0), (IEN | PTD | DIS | M0));
	/* D2D_DMAREQ1  */
	MUX_VAL(CP(D2D_DMAREQ1), (IEN | PTD | DIS | M0));
	/* D2D_DMAREQ2  */
	MUX_VAL(CP(D2D_DMAREQ2), (IEN | PTD | DIS | M0));
	/* D2D_DMAREQ3  */
	MUX_VAL(CP(D2D_DMAREQ3), (IEN | PTD | DIS | M0));
	/* D2D_N3GTRST  */
	MUX_VAL(CP(D2D_N3GTRST), (IEN | PTD | DIS | M0));
	/* D2D_N3GTDI */
	MUX_VAL(CP(D2D_N3GTDI), (IEN | PTD | DIS | M0));
	/* D2D_N3GTDO */
	MUX_VAL(CP(D2D_N3GTDO), (IEN | PTD | DIS | M0));
	/* D2D_N3GTMS */
	MUX_VAL(CP(D2D_N3GTMS), (IEN | PTD | DIS | M0));
	/* D2D_N3GTCK */
	MUX_VAL(CP(D2D_N3GTCK), (IEN | PTD | DIS | M0));
	/* D2D_N3GRTCK  */
	MUX_VAL(CP(D2D_N3GRTCK), (IEN | PTD | DIS | M0));
	/* D2D_MSTDBY */
	MUX_VAL(CP(D2D_MSTDBY), (IEN | PTU | EN | M0));
	/* D2D_SWAKEUP */
	MUX_VAL(CP(D2D_SWAKEUP), (IEN | PTD | EN | M0));
	/* D2D_IDLEREQ */
	MUX_VAL(CP(D2D_IDLEREQ), (IEN | PTD | DIS | M0));
	/* D2D_IDLEACK */
	MUX_VAL(CP(D2D_IDLEACK), (IEN | PTU | EN | M0));
	/* D2D_MWRITE */
	MUX_VAL(CP(D2D_MWRITE), (IEN | PTD | DIS | M0));
	/* D2D_SWRITE */
	MUX_VAL(CP(D2D_SWRITE), (IEN | PTD | DIS | M0));
	/* D2D_MREAD */
	MUX_VAL(CP(D2D_MREAD), (IEN | PTD | DIS | M0));
	/* D2D_SREAD */
	MUX_VAL(CP(D2D_SREAD), (IEN | PTD | DIS | M0));
	/* D2D_MBUSFLAG */
	MUX_VAL(CP(D2D_MBUSFLAG), (IEN | PTD | DIS | M0));
	/* D2D_SBUSFLAG */
	MUX_VAL(CP(D2D_SBUSFLAG), (IEN | PTD | DIS | M0));
	/* SDRC_CKE0 */
	MUX_VAL(CP(SDRC_CKE0), (IDIS | PTU | EN | M0));
	/* SDRC_CKE1 NOT USED */
	MUX_VAL(CP(SDRC_CKE1), (IDIS | PTD | DIS | M7));
#endif				/* CONFIG_MACH_OMAP_ADVANCED_MUX */
}

Beispiel #18

0

Datei anzeigen

Datei: a317.c Projekt: Micronet-Ltd/A3xx-Uboot

/*
 * Routine: misc_init_r
 * Description: Configure board specific parts
 */
int misc_init_r(void)
{
	int err;
	hw_boot_status status_bits;
	unsigned short reg;
	unsigned char  val;
	u8 data;

	/*
	 * Configure drive strength for IO cells
	 */
	// already pulled up on board
	//*(ulong *)(CONTROL_PROG_IO1) &= ~(PRG_I2C2_PULLUPRESX);

	_board_revision();

	printf("%s: initialize TPS65950 voltages\n", __func__);
	twl4030_power_init();
	printf("%s: select TPS65950 power-on HW transitions(PWRON and RTC)\n", __func__);
	twl4030_set_px_transition(0x07, 0x49);
	printf("%s: select 1-GHz MPU clock\n", __func__);
	// 26 MHz * 500 / (12 + 1)
	select_mpu_clock(500, 12);

	lcd_config();

	printf("%s: initialize all peripherals\n", __func__);

	omap_request_gpio(27);	// Enable periph 3V
	omap_request_gpio(34);	// reset USBHUB
	omap_request_gpio(38);	// disable CAN
	omap_request_gpio(40);	// reset modem
	omap_request_gpio(41);	// disable modem
	omap_request_gpio(42);	// reset CAP touch
	omap_request_gpio(43);	// off CAN
	omap_request_gpio(61);	// off modem
	omap_request_gpio(64);	// off GPS
	omap_request_gpio(65);	// off USB PHY
	omap_request_gpio(94);	// automotive out high
	omap_request_gpio(95);	// Wireless module VIO 1.8 V
	omap_request_gpio(98);	// DEVICE_EN
	omap_request_gpio(111);	// off USB PHY
	omap_request_gpio(136);	// Wireless module VDD 3.6 V
	omap_request_gpio(137);	// BT_EN
	omap_request_gpio(138);	// WL_EN
	omap_request_gpio(144);	// disable GPS
	omap_request_gpio(145);	// reset GPS
	omap_request_gpio(146);	// disable GPS boot
	omap_request_gpio(161); // select microphone
	omap_request_gpio(162);	// serial transmitter force on
	omap_request_gpio(175); // shutdown internal speaker amplifier
	omap_request_gpio(176); // shutdown external speaker amplifier
	omap_request_gpio(177); // enable external I2C device
	omap_request_gpio(186);	// PWR_ON generator

	// Enable serial ports transceiver
	omap_set_gpio_dataout(162, 1);
	omap_set_gpio_direction(162, 0);

	omap_set_gpio_dataout(98, 0);
	omap_set_gpio_direction(98, 0);

	omap_set_gpio_dataout(94, 0);
	omap_set_gpio_direction(94, 0);

	// enable peripheral 3.3 V
	omap_set_gpio_dataout(27, 1);
	omap_set_gpio_direction(27, 0);

	// PWR_ON generator will off
	omap_set_gpio_dataout(186, 1);
	omap_set_gpio_direction(186, 0);

	// disable BT
	omap_set_gpio_dataout(137, 0);
	omap_set_gpio_direction(137, 0);

	// disable WL
	omap_set_gpio_dataout(138, 0);
	omap_set_gpio_direction(138, 0);

	// wireless VIO 1.8V off
	omap_set_gpio_dataout(95, 0);
	omap_set_gpio_direction(95, 0);

	// remove wireless VDD 3.6 V
	omap_set_gpio_dataout(136, 0);
	omap_set_gpio_direction(136, 0);

	udelay(100000);

	// Supply VDD and VIO to WiFi
	omap_set_gpio_dataout(136, 1);
	omap_set_gpio_dataout(95, 1);

	udelay(100000);

	// enable digital PADs
	// MMC2
	MUX_VAL(CP(MMC2_CLK),	(IEN  | PTU | EN  | M0))
	MUX_VAL(CP(MMC2_CMD),	(IEN  | PTU | EN  | M0))
	MUX_VAL(CP(MMC2_DAT0),	(IEN  | PTU | EN  | M0))
	MUX_VAL(CP(MMC2_DAT1),	(IEN  | PTU | EN  | M0))
	MUX_VAL(CP(MMC2_DAT2),	(IEN  | PTU | EN  | M0))
	MUX_VAL(CP(MMC2_DAT3),	(IEN  | PTU | EN  | M0))
	// UART2
	MUX_VAL(CP(MCBSP3_FSX), (IEN  | PTD | DIS | M1))
	MUX_VAL(CP(MCBSP3_CLKX),(IDIS | PTD | DIS | M1))
	MUX_VAL(CP(MCBSP3_DR),  (IDIS | PTD | DIS | M1))
	MUX_VAL(CP(MCBSP3_DX),  (IEN  | PTD | DIS | M1))

	udelay(200000);

	// pulse enable pins
	// enable WL
	omap_set_gpio_dataout(138, 1);
	// enable BT
	omap_set_gpio_dataout(137, 1);

	udelay(200000);

	// Valdimir: temporary enabled
	// disable BT
	//omap_set_gpio_dataout(137, 0);
	// disable WL
	//omap_set_gpio_dataout(138, 0);

	omap_set_gpio_dataout(41, 0);
	omap_set_gpio_direction(41, 0);
	omap_set_gpio_dataout(40, 0);
	omap_set_gpio_direction(40, 0);
	omap_set_gpio_dataout(61, 0);
	omap_set_gpio_direction(61, 0);

	omap_set_gpio_dataout(144, 0);
	omap_set_gpio_direction(144, 0);
	omap_set_gpio_dataout(145, 0);
	omap_set_gpio_direction(145, 0);
	omap_set_gpio_dataout(146, 0);
	omap_set_gpio_direction(146, 0);
	omap_set_gpio_dataout(64, 0);
	omap_set_gpio_direction(64, 0);

	omap_set_gpio_dataout(38, 0);
	omap_set_gpio_direction(38, 0);
	omap_set_gpio_dataout(43, 0);
	omap_set_gpio_direction(43, 0);

	omap_set_gpio_dataout(42, 0);
	omap_set_gpio_direction(42, 0);

	omap_set_gpio_dataout(34, 0);
	omap_set_gpio_direction(34, 0);
	omap_set_gpio_dataout(111, 1);
	omap_set_gpio_direction(111, 0);
	omap_set_gpio_dataout(65, 0);
	omap_set_gpio_direction(65, 0);

	// enable internal speaker amplifier
	omap_set_gpio_dataout(175, 0);
	omap_set_gpio_direction(175, 0);
	// shutdown external speaker amplifier
	omap_set_gpio_dataout(176, 0);
	omap_set_gpio_direction(176, 0);
	// select internal microphone
	omap_set_gpio_dataout(161, 0);
	omap_set_gpio_direction(161, 0);

	// External I2C Bus enable
	omap_set_gpio_dataout(177, 0);
	omap_set_gpio_direction(177, 0);

	omap_free_gpio(27);
	omap_free_gpio(34);
	omap_free_gpio(38);
	omap_free_gpio(40);
	omap_free_gpio(41);
	omap_free_gpio(42);
	omap_free_gpio(43);
	omap_free_gpio(61);
	omap_free_gpio(64);
	omap_free_gpio(65);
	omap_free_gpio(94);
	omap_free_gpio(95);
	omap_free_gpio(98);
	omap_free_gpio(111);
	omap_free_gpio(136);
	omap_free_gpio(137);
	omap_free_gpio(138);
	omap_free_gpio(144);
	omap_free_gpio(145);
	omap_free_gpio(146);
	omap_free_gpio(161);
	omap_free_gpio(162);
	omap_free_gpio(175);
	omap_free_gpio(177);
	omap_free_gpio(186);

	printf("%s: initialize all peripherals done\n", __func__);

	twl4030_keypad_init();

	// TODO: thermal shutdown and dynamic frequency scaling
	// TPS659XX PHY 3.3 V recovery workaround
	// Status bits read from companion chip and OMAP
	twl4030_i2c_read_u8(TWL4030_CHIP_RTC, &data, TWL_BACKUP_REG_G); //TWL_BACKUP_REG_G - set in thermal driver
	status_bits.thermal = data;

	twl4030_i2c_read_u8(TWL4030_CHIP_RTC, &data, TWL_RTC_STATUS_REG); //TWL_RTC_STATUS_REG
	status_bits.rtc_power_up = (data & TWL_RTC_STATUS_POWER_UP)	? 1 : 0;
	status_bits.rtc_alarm	= (data & TWL_RTC_STATUS_ALARM)		? 1 : 0;	
	status_bits.rtc_event	= (data & (TWL_RTC_STATUS_ONE_D_EVENT | TWL_RTC_STATUS_ONE_H_EVENT |
									   TWL_RTC_STATUS_ONE_M_EVENT | TWL_RTC_STATUS_ONE_S_EVENT))? 1 : 0;

	twl4030_i2c_read_u8(TWL4030_CHIP_RTC, &data, TWL_RTC_INTERRUPTS_REG); //TWL_RTC_INTERRUPTS_REG
	status_bits.rtc_it_timer = (data & TWL_RTC_INTERRUPTS_IT_TIMER) ? 1 : 0;
	status_bits.rtc_it_alarm = (data & TWL_RTC_INTERRUPTS_IT_ALARM) ? 1 : 0;

	twl4030_i2c_read_u8(TWL4030_CHIP_RTC, &data, TWL_STS_BOOT); //TWL_STS_BOOT
	status_bits.watchdog_reset = (data & (1<<5))   ? 1 : 0;//TWL_WATCHDOG_RESET

	twl4030_i2c_read_u8(TWL4030_CHIP_RTC, &data, TWL_STS_HW_CONDITIONS); //TWL_STS_HW_CONDITIONS
	status_bits.sts_pwon = (data & 1)      ? 1 : 0; //STS_PWON		
	status_bits.sts_warmreset    = (data & (1<<3)) ? 1 : 0; //STS_WARMRESET

	twl4030_i2c_read_u8(TWL4030_CHIP_RTC, &data, TWL_PWR_ISR1); //TWL_PWR_ISR1
	status_bits.isr_pwron	= (data & STARTON_RTC)	? 1 : 0;
	status_bits.isr_rtc_it	= (data & STARTON_PWON)	? 1 : 0;

	status_bits.prm_rstst = readl(OMAP_PRCM_PRM_RSTST);

	char str[9];

	sprintf(str, "%d", status_bits.bits);

	setenv("hw_stat", str);

	printf("Status bits [0x%x] [%s]\n", status_bits.bits, str);

	printf("Board Revision A317 (%d)\n", board_revision);

	sprintf(str, "%s", "A-317");
	setenv("product", str);

	dieid_num_r();

	return 0;
}

Beispiel #19

0

Datei anzeigen

Datei: mux.c Projekt: ehamine/u-boot

void set_muxconf_regs(void)
{
    /* SDRC */
    MUX_VAL(CP(SDRC_D0),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D1),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D2),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D3),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D4),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D5),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D6),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D7),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D8),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D9),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D10),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D11),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D12),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D13),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D14),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D15),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D16),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D17),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D18),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D19),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D20),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D21),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D22),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D23),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D24),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D25),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D26),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D27),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D28),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D29),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D30),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_D31),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_CLK),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_DQS0),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_DQS1),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_DQS2),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_DQS3),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(SDRC_CKE0),		(IDIS | PTU | EN  | M0));
    MUX_VAL(CP(SDRC_CKE1),		(IDIS | PTD | DIS | M7));

    /* GPMC */
    MUX_VAL(CP(GPMC_A1),		(IDIS | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_A2),		(IDIS | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_A3),		(IDIS | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_A4),		(IDIS | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_A5),		(IDIS | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_A6),		(IDIS | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_A7),		(IDIS | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_A8),		(IDIS | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_A9),		(IDIS | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_A10),		(IDIS | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_D0),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_D1),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_D2),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_D3),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_D4),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_D5),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_D6),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_D7),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_D8),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_D9),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_D10),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_D11),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_D12),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_D13),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_D14),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_D15),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(GPMC_NCS0),		(IDIS | PTU | EN  | M0));

    /* SB-T35 Ethernet */
    MUX_VAL(CP(GPMC_NCS4),		(IEN  | PTU | EN  | M0));
    /* DVI enable */
    MUX_VAL(CP(GPMC_NCS3),		(IDIS | PTU | DIS  | M4));/*GPIO_54*/
    /* DataImage backlight */
    MUX_VAL(CP(GPMC_NCS7),		(IDIS | PTU | DIS  | M4));/*GPIO_58*/

    /* SB-T35 SD/MMC WP GPIO59 */
    MUX_VAL(CP(GPMC_CLK),		(IEN  | PTU | EN  | M4)); /*GPIO_59*/
    MUX_VAL(CP(GPMC_NWE),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(GPMC_NOE),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(GPMC_NADV_ALE),	(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(GPMC_NBE0_CLE),	(IDIS | PTU | EN  | M0));
    /* SB-T35 Audio Enable GPIO61 */
    MUX_VAL(CP(GPMC_NBE1),		(IDIS | PTU | EN  | M4)); /*GPIO_61*/
    MUX_VAL(CP(GPMC_NWP),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(GPMC_WAIT0),		(IEN  | PTU | EN  | M0));
    /* SB-T35 Ethernet IRQ GPIO65 */
    MUX_VAL(CP(GPMC_WAIT3),		(IEN  | PTU | EN  | M4)); /*GPIO_65*/

    /* UART3 Console */
    MUX_VAL(CP(UART3_RX_IRRX),	(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(UART3_TX_IRTX),	(IDIS | PTD | DIS | M0));
    /* RTC V3020 nCS GPIO163 */
    MUX_VAL(CP(UART3_CTS_RCTX),	(IEN  | PTU | EN  | M4)); /*GPIO_163*/
    /* SB-T35 Ethernet nRESET GPIO164 */
    MUX_VAL(CP(UART3_RTS_SD),	(IDIS | PTU | EN  | M4)); /*GPIO_164*/

    /* SB-T35 SD/MMC CD GPIO144 */
    MUX_VAL(CP(UART2_CTS),		(IEN  | PTU | EN  | M4)); /*GPIO_144*/
    /* WIFI nRESET GPIO145 */
    MUX_VAL(CP(UART2_RTS),		(IEN  | PTD | EN  | M4)); /*GPIO_145*/
    /* USB1 PHY Reset GPIO 146 */
    MUX_VAL(CP(UART2_TX),		(IEN  | PTD | EN  | M4)); /*GPIO_146*/
    /* USB2 PHY Reset GPIO 147 */
    MUX_VAL(CP(UART2_RX),		(IEN  | PTD | EN  | M4)); /*GPIO_147*/

    /* MMC1 */
    MUX_VAL(CP(MMC1_CLK),		(IDIS | PTU | EN  | M0));
    MUX_VAL(CP(MMC1_CMD),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(MMC1_DAT0),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(MMC1_DAT1),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(MMC1_DAT2),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(MMC1_DAT3),		(IEN  | PTU | EN  | M0));

    /* DSS */
    MUX_VAL(CP(DSS_PCLK),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_HSYNC),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_VSYNC),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_ACBIAS),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA0),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA1),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA2),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA3),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA4),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA5),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA6),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA7),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA8),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA9),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA10),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA11),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA12),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA13),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA14),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA15),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA16),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA17),		(IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA18),         (IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA19),         (IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA20),         (IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA21),         (IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA22),         (IDIS | PTD | DIS | M0));
    MUX_VAL(CP(DSS_DATA23),         (IDIS | PTD | DIS | M0));

    /* I2C */
    MUX_VAL(CP(I2C1_SCL),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(I2C1_SDA),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(I2C3_SCL),		(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(I2C3_SDA),		(IEN  | PTU | EN  | M0));

    /* SB-T35 USB HUB Reset GPIO98 */
    MUX_VAL(CP(CCDC_WEN),		(IDIS | PTU | EN  | M4)); /*GPIO_98*/
    /* CM-T3517 USB HUB Reset GPIO152 */
    MUX_VAL(CP(MCBSP4_CLKX),	(IDIS | PTD | DIS | M4)); /*GPIO_152*/

    /* RMII */
    MUX_VAL(CP(RMII_MDIO_DATA),	(IEN  | PTU | EN  | M0));
    MUX_VAL(CP(RMII_MDIO_CLK),	(M0));
    MUX_VAL(CP(RMII_RXD0),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(RMII_RXD1),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(RMII_CRS_DV),	(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(RMII_RXER),		(IEN  | PTD | DIS | M0));
    MUX_VAL(CP(RMII_TXD0),		(IDIS | M0));
    MUX_VAL(CP(RMII_TXD1),		(IDIS | M0));
    MUX_VAL(CP(RMII_TXEN),		(IDIS | M0));
    MUX_VAL(CP(RMII_50MHZ_CLK),	(IEN  | PTU | DIS | M0));

    /* Green LED GPIO186 */
    MUX_VAL(CP(SYS_CLKOUT2),	(IDIS | PTU | DIS | M4)); /*GPIO_186*/

    /* SPI */
    MUX_VAL(CP(MCBSP1_CLKR),	(IEN | PTD | DIS | M1)); /*MCSPI4_CLK*/
    MUX_VAL(CP(MCBSP1_DX),		(IEN | PTD | DIS | M1)); /*MCSPI4_SIMO*/
    MUX_VAL(CP(MCBSP1_DR),		(IEN | PTD | DIS | M1)); /*MCSPI4_SOMI*/
    MUX_VAL(CP(MCBSP1_FSX),		(IEN | PTU | EN  | M1)); /*MCSPI4_CS0*/
    /* LCD reset GPIO157 */
    MUX_VAL(CP(MCBSP1_FSR),		(IDIS | PTU | DIS | M4)); /*GPIO_157*/

    /* RTC V3020 CS Enable GPIO160 */
    MUX_VAL(CP(MCBSP_CLKS),		(IEN  | PTD | EN  | M4)); /*GPIO_160*/
    /* SB-T35 LVDS Transmitter SHDN GPIO162 */
    MUX_VAL(CP(MCBSP1_CLKX),	(IEN  | PTU | DIS | M4)); /*GPIO_162*/

    /* USB0 - mUSB */
    MUX_VAL(CP(USB0_DRVBUS),	(IEN  | PTD | EN  | M0));
    /* USB1 EHCI */
    MUX_VAL(CP(ETK_D0_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT0*/
    MUX_VAL(CP(ETK_D1_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT1*/
    MUX_VAL(CP(ETK_D2_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT2*/
    MUX_VAL(CP(ETK_D7_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT3*/
    MUX_VAL(CP(ETK_D4_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT4*/
    MUX_VAL(CP(ETK_D5_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT5*/
    MUX_VAL(CP(ETK_D6_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT6*/
    MUX_VAL(CP(ETK_D3_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DT7*/
    MUX_VAL(CP(ETK_D8_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_DIR*/
    MUX_VAL(CP(ETK_D9_ES2),		(IEN  | PTD | EN  | M3)); /*HSUSB1_NXT*/
    MUX_VAL(CP(ETK_CTL_ES2),	(IDIS | PTD | DIS | M3)); /*HSUSB1_CLK*/
    MUX_VAL(CP(ETK_CLK_ES2),	(IDIS | PTU | DIS | M3)); /*HSUSB1_STP*/
    /* USB2 EHCI */
    MUX_VAL(CP(ETK_D14_ES2),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DT0*/
    MUX_VAL(CP(ETK_D15_ES2),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DT1*/
    MUX_VAL(CP(MCSPI1_CS3),		(IEN  | PTD | EN  | M3)); /*HSUSB2_DT2*/
    MUX_VAL(CP(MCSPI2_CS1),		(IEN  | PTD | EN  | M3)); /*HSUSB2_DT3*/
    MUX_VAL(CP(MCSPI2_SIMO),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DT4*/
    MUX_VAL(CP(MCSPI2_SOMI),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DT5*/
    MUX_VAL(CP(MCSPI2_CS0),		(IEN  | PTD | EN  | M3)); /*HSUSB2_DT6*/
    MUX_VAL(CP(MCSPI2_CLK),		(IEN  | PTD | EN  | M3)); /*HSUSB2_DT7*/
    MUX_VAL(CP(ETK_D12_ES2),	(IEN  | PTD | EN  | M3)); /*HSUSB2_DIR*/
    MUX_VAL(CP(ETK_D13_ES2),	(IEN  | PTD | EN  | M3)); /*HSUSB2_NXT*/
    MUX_VAL(CP(ETK_D10_ES2),	(IDIS | PTD | DIS | M3)); /*HSUSB2_CLK*/
    MUX_VAL(CP(ETK_D11_ES2),	(IDIS | PTU | DIS | M3)); /*HSUSB2_STP*/

    /* SYS_BOOT */
    MUX_VAL(CP(SYS_BOOT0),		(IEN  | PTU | DIS | M4)); /*GPIO_2*/
    MUX_VAL(CP(SYS_BOOT1),		(IEN  | PTU | DIS | M4)); /*GPIO_3*/
    MUX_VAL(CP(SYS_BOOT2),		(IEN  | PTU | DIS | M4)); /*GPIO_4*/
    MUX_VAL(CP(SYS_BOOT3),		(IEN  | PTU | DIS | M4)); /*GPIO_5*/
    MUX_VAL(CP(SYS_BOOT4),		(IEN  | PTU | DIS | M4)); /*GPIO_6*/
    MUX_VAL(CP(SYS_BOOT5),		(IEN  | PTU | DIS | M4)); /*GPIO_7*/
}