void __init imx27_init_early(void)
{
mxc_set_cpu_type(MXC_CPU_MX27);
mxc_arch_reset_init(MX27_IO_ADDRESS(MX27_WDOG_BASE_ADDR));
imx_iomuxv1_init(MX27_IO_ADDRESS(MX27_GPIO_BASE_ADDR),
MX27_NUM_GPIO_PORT);
}
static int mx27_suspend_enter(suspend_state_t state)
{
u32 cscr;
switch (state) {
case PM_SUSPEND_MEM:
/* Clear MPEN and SPEN to disable MPLL/SPLL */
cscr = imx_readl(MX27_IO_ADDRESS(MX27_CCM_BASE_ADDR));
cscr &= 0xFFFFFFFC;
imx_writel(cscr, MX27_IO_ADDRESS(MX27_CCM_BASE_ADDR));
/* Executes WFI */
cpu_do_idle();
break;
default:
return -EINVAL;
}
return 0;
}
int mx27_initialize_usb_hw(int port, unsigned int flags)
{
unsigned int v;
v = readl(MX27_IO_ADDRESS(MX27_USB_BASE_ADDR + USBCTRL_OTGBASE_OFFSET));
switch (port) {
case 0: /* OTG port */
v &= ~(MX27_OTG_SIC_MASK | MX27_OTG_PM_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX27_OTG_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX27_OTG_PM_BIT;
break;
case 1: /* H1 port */
v &= ~(MX27_H1_SIC_MASK | MX27_H1_PM_BIT | MX27_H1_DT_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX27_H1_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX27_H1_PM_BIT;
if (!(flags & MXC_EHCI_TTL_ENABLED))
v |= MX27_H1_DT_BIT;
break;
case 2: /* H2 port */
v &= ~(MX27_H2_SIC_MASK | MX27_H2_PM_BIT | MX27_H2_DT_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX27_H2_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX27_H2_PM_BIT;
if (!(flags & MXC_EHCI_TTL_ENABLED))
v |= MX27_H2_DT_BIT;
break;
default:
return -EINVAL;
}
writel(v, MX27_IO_ADDRESS(MX27_USB_BASE_ADDR + USBCTRL_OTGBASE_OFFSET));
return 0;
}
static int mxc_audmux_v1_init(void)
{
#ifdef CONFIG_MACH_MX21
if (cpu_is_mx21())
audmux_base = MX21_IO_ADDRESS(MX21_AUDMUX_BASE_ADDR);
else
#endif
#ifdef CONFIG_MACH_MX27
if (cpu_is_mx27())
audmux_base = MX27_IO_ADDRESS(MX27_AUDMUX_BASE_ADDR);
else
#endif
(void)0;
return 0;
}
void __init imx27_soc_init(void)
{
mxc_arch_reset_init(MX27_IO_ADDRESS(MX27_WDOG_BASE_ADDR));
mxc_device_init();
/* i.mx27 has the i.mx21 type gpio */
mxc_register_gpio("imx21-gpio", 0, MX27_GPIO1_BASE_ADDR, SZ_256, MX27_INT_GPIO, 0);
mxc_register_gpio("imx21-gpio", 1, MX27_GPIO2_BASE_ADDR, SZ_256, MX27_INT_GPIO, 0);
mxc_register_gpio("imx21-gpio", 2, MX27_GPIO3_BASE_ADDR, SZ_256, MX27_INT_GPIO, 0);
mxc_register_gpio("imx21-gpio", 3, MX27_GPIO4_BASE_ADDR, SZ_256, MX27_INT_GPIO, 0);
mxc_register_gpio("imx21-gpio", 4, MX27_GPIO5_BASE_ADDR, SZ_256, MX27_INT_GPIO, 0);
mxc_register_gpio("imx21-gpio", 5, MX27_GPIO6_BASE_ADDR, SZ_256, MX27_INT_GPIO, 0);
pinctrl_provide_dummies();
imx_add_imx_dma("imx27-dma", MX27_DMA_BASE_ADDR,
MX27_INT_DMACH0, 0); /* No ERR irq */
/* imx27 has the imx21 type audmux */
platform_device_register_simple("imx21-audmux", 0, imx27_audmux_res,
ARRAY_SIZE(imx27_audmux_res));
imx27_pm_init();
}
static int imx_iomuxv1_init(void)
{
#ifdef CONFIG_ARCH_MX1
if (cpu_is_mx1()) {
imx_iomuxv1_baseaddr = MX1_IO_ADDRESS(MX1_GPIO_BASE_ADDR);
imx_iomuxv1_numports = MX1_NUM_GPIO_PORT;
} else
#endif
#ifdef CONFIG_MACH_MX21
if (cpu_is_mx21()) {
imx_iomuxv1_baseaddr = MX21_IO_ADDRESS(MX21_GPIO_BASE_ADDR);
imx_iomuxv1_numports = MX21_NUM_GPIO_PORT;
} else
#endif
#ifdef CONFIG_MACH_MX27
if (cpu_is_mx27()) {
imx_iomuxv1_baseaddr = MX27_IO_ADDRESS(MX27_GPIO_BASE_ADDR);
imx_iomuxv1_numports = MX27_NUM_GPIO_PORT;
} else
#endif
return -ENODEV;
return 0;
}
/* On pcm038 there's a sram attached to CS1, we enable the chipselect here and
* setup other stuffs to access the sram. */
static void __init pcm038_init_sram(void)
{
__raw_writel(0x0000d843, MX27_IO_ADDRESS(MX27_WEIM_CSCRxU(1)));
__raw_writel(0x22252521, MX27_IO_ADDRESS(MX27_WEIM_CSCRxL(1)));
__raw_writel(0x22220a00, MX27_IO_ADDRESS(MX27_WEIM_CSCRxA(1)));
}
int mxc_initialize_usb_hw(int port, unsigned int flags)
{
unsigned int v;
#if defined(CONFIG_ARCH_MX25)
if (cpu_is_mx25()) {
v = readl(MX25_IO_ADDRESS(MX25_OTG_BASE_ADDR +
USBCTRL_OTGBASE_OFFSET));
switch (port) {
case 0: /* OTG port */
v &= ~(MX35_OTG_SIC_MASK | MX35_OTG_PM_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX35_OTG_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX35_OTG_PM_BIT;
break;
case 1: /* H1 port */
v &= ~(MX35_H1_SIC_MASK | MX35_H1_PM_BIT | MX35_H1_TLL_BIT |
MX35_H1_USBTE_BIT | MX35_H1_IPPUE_DOWN_BIT | MX35_H1_IPPUE_UP_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX35_H1_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX35_H1_PM_BIT;
if (!(flags & MXC_EHCI_TTL_ENABLED))
v |= MX35_H1_TLL_BIT;
if (flags & MXC_EHCI_INTERNAL_PHY)
v |= MX35_H1_USBTE_BIT;
if (flags & MXC_EHCI_IPPUE_DOWN)
v |= MX35_H1_IPPUE_DOWN_BIT;
if (flags & MXC_EHCI_IPPUE_UP)
v |= MX35_H1_IPPUE_UP_BIT;
break;
default:
return -EINVAL;
}
writel(v, MX25_IO_ADDRESS(MX25_OTG_BASE_ADDR +
USBCTRL_OTGBASE_OFFSET));
return 0;
}
#endif /* CONFIG_ARCH_MX25 */
#if defined(CONFIG_ARCH_MX3)
if (cpu_is_mx31()) {
v = readl(MX31_IO_ADDRESS(MX31_OTG_BASE_ADDR +
USBCTRL_OTGBASE_OFFSET));
switch (port) {
case 0: /* OTG port */
v &= ~(MX31_OTG_SIC_MASK | MX31_OTG_PM_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX31_OTG_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX31_OTG_PM_BIT;
break;
case 1: /* H1 port */
v &= ~(MX31_H1_SIC_MASK | MX31_H1_PM_BIT | MX31_H1_DT_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX31_H1_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX31_H1_PM_BIT;
if (!(flags & MXC_EHCI_TTL_ENABLED))
v |= MX31_H1_DT_BIT;
break;
case 2: /* H2 port */
v &= ~(MX31_H2_SIC_MASK | MX31_H2_PM_BIT | MX31_H2_DT_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX31_H2_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX31_H2_PM_BIT;
if (!(flags & MXC_EHCI_TTL_ENABLED))
v |= MX31_H2_DT_BIT;
break;
default:
return -EINVAL;
}
writel(v, MX31_IO_ADDRESS(MX31_OTG_BASE_ADDR +
USBCTRL_OTGBASE_OFFSET));
return 0;
}
if (cpu_is_mx35()) {
v = readl(MX35_IO_ADDRESS(MX35_OTG_BASE_ADDR +
USBCTRL_OTGBASE_OFFSET));
switch (port) {
case 0: /* OTG port */
v &= ~(MX35_OTG_SIC_MASK | MX35_OTG_PM_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX35_OTG_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX35_OTG_PM_BIT;
break;
case 1: /* H1 port */
v &= ~(MX35_H1_SIC_MASK | MX35_H1_PM_BIT | MX35_H1_TLL_BIT |
MX35_H1_USBTE_BIT | MX35_H1_IPPUE_DOWN_BIT | MX35_H1_IPPUE_UP_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX35_H1_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX35_H1_PM_BIT;
if (!(flags & MXC_EHCI_TTL_ENABLED))
v |= MX35_H1_TLL_BIT;
if (flags & MXC_EHCI_INTERNAL_PHY)
v |= MX35_H1_USBTE_BIT;
if (flags & MXC_EHCI_IPPUE_DOWN)
v |= MX35_H1_IPPUE_DOWN_BIT;
if (flags & MXC_EHCI_IPPUE_UP)
v |= MX35_H1_IPPUE_UP_BIT;
break;
default:
return -EINVAL;
}
writel(v, MX35_IO_ADDRESS(MX35_OTG_BASE_ADDR +
USBCTRL_OTGBASE_OFFSET));
return 0;
}
#endif /* CONFIG_ARCH_MX3 */
#ifdef CONFIG_MACH_MX27
if (cpu_is_mx27()) {
/* On i.MX27 we can use the i.MX31 USBCTRL bits, they
* are identical
*/
v = readl(MX27_IO_ADDRESS(MX27_OTG_BASE_ADDR +
USBCTRL_OTGBASE_OFFSET));
switch (port) {
case 0: /* OTG port */
v &= ~(MX31_OTG_SIC_MASK | MX31_OTG_PM_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX31_OTG_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX31_OTG_PM_BIT;
break;
case 1: /* H1 port */
v &= ~(MX31_H1_SIC_MASK | MX31_H1_PM_BIT | MX31_H1_DT_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX31_H1_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX31_H1_PM_BIT;
if (!(flags & MXC_EHCI_TTL_ENABLED))
v |= MX31_H1_DT_BIT;
break;
case 2: /* H2 port */
v &= ~(MX31_H2_SIC_MASK | MX31_H2_PM_BIT | MX31_H2_DT_BIT);
v |= (flags & MXC_EHCI_INTERFACE_MASK)
<< MX31_H2_SIC_SHIFT;
if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
v |= MX31_H2_PM_BIT;
if (!(flags & MXC_EHCI_TTL_ENABLED))
v |= MX31_H2_DT_BIT;
break;
default:
return -EINVAL;
}
writel(v, MX27_IO_ADDRESS(MX27_OTG_BASE_ADDR +
USBCTRL_OTGBASE_OFFSET));
return 0;
}
#endif /* CONFIG_MACH_MX27 */
#ifdef CONFIG_ARCH_MX51
if (cpu_is_mx51()) {
void __iomem *usb_base;
u32 usbotg_base;
u32 usbother_base;
int ret = 0;
usb_base = ioremap(MX51_OTG_BASE_ADDR, SZ_4K);
switch (port) {
case 0: /* OTG port */
usbotg_base = usb_base + MXC_OTG_OFFSET;
break;
case 1: /* Host 1 port */
usbotg_base = usb_base + MXC_H1_OFFSET;
break;
default:
printk(KERN_ERR"%s no such port %d\n", __func__, port);
ret = -ENOENT;
goto error;
}
usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
switch (port) {
case 0: /*OTG port */
if (flags & MXC_EHCI_INTERNAL_PHY) {
v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET);
if (flags & MXC_EHCI_POWER_PINS_ENABLED)
v |= (MXC_OTG_PHYCTRL_OC_DIS_BIT | MXC_OTG_UCTRL_OPM_BIT); /* OC/USBPWR is not used */
else
v &= ~(MXC_OTG_PHYCTRL_OC_DIS_BIT | MXC_OTG_UCTRL_OPM_BIT); /* OC/USBPWR is used */
__raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET);
v = __raw_readl(usbother_base + MXC_USBCTRL_OFFSET);
if (flags & MXC_EHCI_WAKEUP_ENABLED)
v |= MXC_OTG_UCTRL_OWIE_BIT;/* OTG wakeup enable */
else
v &= ~MXC_OTG_UCTRL_OWIE_BIT;/* OTG wakeup disable */
__raw_writel(v, usbother_base + MXC_USBCTRL_OFFSET);
}
break;
case 1: /* Host 1 */
/*Host ULPI */
v = __raw_readl(usbother_base + MXC_USBCTRL_OFFSET);
if (flags & MXC_EHCI_WAKEUP_ENABLED)
v &= ~(MXC_H1_UCTRL_H1WIE_BIT | MXC_H1_UCTRL_H1UIE_BIT);/* HOST1 wakeup/ULPI intr disable */
else
v &= ~(MXC_H1_UCTRL_H1WIE_BIT | MXC_H1_UCTRL_H1UIE_BIT);/* HOST1 wakeup/ULPI intr disable */
if (flags & MXC_EHCI_POWER_PINS_ENABLED)
v &= ~MXC_H1_UCTRL_H1PM_BIT; /* HOST1 power mask used*/
else
v |= MXC_H1_UCTRL_H1PM_BIT; /* HOST1 power mask used*/
__raw_writel(v, usbother_base + MXC_USBCTRL_OFFSET);
v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET);
if (flags & MXC_EHCI_POWER_PINS_ENABLED)
v &= ~MXC_H1_OC_DIS_BIT; /* OC is used */
else
v |= MXC_H1_OC_DIS_BIT; /* OC is not used */
__raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET);
v = __raw_readl(usbotg_base + MXC_USBCMD_OFFSET);
if (flags & MXC_EHCI_ITC_NO_THRESHOLD)
/* Interrupt Threshold Control:Immediate (no threshold) */
v &= MXC_UCMD_ITC_NO_THRESHOLD_MASK;
__raw_writel(v, usbotg_base + MXC_USBCMD_OFFSET);
break;
}
error:
iounmap(usb_base);
return ret;
}
#endif
printk(KERN_WARNING
"%s() unable to setup USBCONTROL for this CPU\n", __func__);
return -EINVAL;
}
void __init mx27_init_irq(void)
{
mxc_init_irq(MX27_IO_ADDRESS(MX27_AVIC_BASE_ADDR));
}
void __init mx27_init_irq(void)
{
mxc_init_irq(MX27_IO_ADDRESS(MX27_AVIC_BASE_ADDR));
mxc_gpio_init(imx27_gpio_ports, ARRAY_SIZE(imx27_gpio_ports));
}
