C++ (Cpp) board_is_gpevm Beispiele

Beispiel #1

Datei: mux.c Projekt: 13xiaobang/mini2440-uboot_2016.01

void enable_board_pin_mux(void)
{
	configure_module_pin_mux(mmc0_pin_mux);
	configure_module_pin_mux(i2c0_pin_mux);
	configure_module_pin_mux(mdio_pin_mux);

	if (board_is_gpevm()) {
		configure_module_pin_mux(gpio5_7_pin_mux);
		configure_module_pin_mux(rgmii1_pin_mux);
#if defined(CONFIG_NAND)
		configure_module_pin_mux(nand_pin_mux);
#endif
	} else if (board_is_sk() || board_is_idk()) {
		configure_module_pin_mux(rgmii1_pin_mux);
#if defined(CONFIG_NAND)
		printf("Error: NAND flash not present on this board\n");
#endif
		configure_module_pin_mux(qspi_pin_mux);
	} else if (board_is_eposevm()) {
		configure_module_pin_mux(rmii1_pin_mux);
#if defined(CONFIG_NAND)
		configure_module_pin_mux(nand_pin_mux);
#else
		configure_module_pin_mux(qspi_pin_mux);
#endif
	}
}

Beispiel #2

Datei: board.c Projekt: R2F/u-boot_ARMv7M

const struct dpll_params *get_dpll_ddr_params(void)
{
	if (board_is_eposevm())
		return &epos_evm_dpll_ddr;
	else if (board_is_gpevm() || board_is_sk())
		return &gp_evm_dpll_ddr;

	printf(" Board '%s' not supported\n", am43xx_board_name);
	return NULL;
}

Beispiel #3

Datei: board.c Projekt: iakov/trik-u-boot

void emif_get_ext_phy_ctrl_const_regs(const u32 **regs, u32 *size)
{
    if (board_is_eposevm()) {
        *regs = ext_phy_ctrl_const_base_lpddr2;
        *size = ARRAY_SIZE(ext_phy_ctrl_const_base_lpddr2);
    } else if (board_is_gpevm()) {
        *regs = ext_phy_ctrl_const_base_ddr3;
        *size = ARRAY_SIZE(ext_phy_ctrl_const_base_ddr3);
    }

    return;
}

Beispiel #4

Datei: mux.c Projekt: dzemskov/pia-uboot

void enable_board_pin_mux(void)
{
    configure_module_pin_mux(mmc0_pin_mux);
    configure_module_pin_mux(i2c0_pin_mux);
    configure_module_pin_mux(mdio_pin_mux);

    if (board_is_gpevm()) {
        configure_module_pin_mux(gpio5_7_pin_mux);
        configure_module_pin_mux(rgmii1_pin_mux);
    } else if (board_is_eposevm()) {
        configure_module_pin_mux(rmii1_pin_mux);
        configure_module_pin_mux(qspi_pin_mux);
    }
}

Beispiel #5

Datei: board.c Projekt: jsarenik/u-boot

u32 rtc_only_get_board_type(void)
{
	if (board_is_eposevm())
		return RTC_BOARD_EPOS;
	else if (board_is_evm_14_or_later())
		return RTC_BOARD_EVM14;
	else if (board_is_evm_12_or_later())
		return RTC_BOARD_EVM12;
	else if (board_is_gpevm())
		return RTC_BOARD_GPEVM;
	else if (board_is_sk())
		return RTC_BOARD_SK;

	return 0;
}

Beispiel #6

Datei: board.c Projekt: iakov/trik-u-boot

const struct dpll_params *get_dpll_ddr_params(void)
{
    struct am43xx_board_id header;

    enable_i2c0_pin_mux();
    i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
    if (read_eeprom(&header) < 0)
        puts("Could not get board ID.\n");

    if (board_is_eposevm())
        return &epos_evm_dpll_ddr;
    else if (board_is_gpevm())
        return &gp_evm_dpll_ddr;

    puts(" Board not supported\n");
    return NULL;
}

Beispiel #7

Datei: board.c Projekt: R2F/u-boot_ARMv7M

void emif_get_ext_phy_ctrl_const_regs(const u32 **regs, u32 *size)
{
	if (board_is_eposevm()) {
		*regs = ext_phy_ctrl_const_base_lpddr2;
		*size = ARRAY_SIZE(ext_phy_ctrl_const_base_lpddr2);
	} else if (board_is_evm_14_or_later()) {
		*regs = ext_phy_ctrl_const_base_ddr3_production;
		*size = ARRAY_SIZE(ext_phy_ctrl_const_base_ddr3_production);
	} else if (board_is_evm_12_or_later()) {
		*regs = ext_phy_ctrl_const_base_ddr3_beta;
		*size = ARRAY_SIZE(ext_phy_ctrl_const_base_ddr3_beta);
	} else if (board_is_gpevm()) {
		*regs = ext_phy_ctrl_const_base_ddr3;
		*size = ARRAY_SIZE(ext_phy_ctrl_const_base_ddr3);
	} else if (board_is_sk()) {
		*regs = ext_phy_ctrl_const_base_ddr3_sk;
		*size = ARRAY_SIZE(ext_phy_ctrl_const_base_ddr3_sk);
	}

	return;
}