void board_BeforeAgesa(struct sysinfo *cb)
{
u8 byte;
/* Enable the AcpiMmio space */
outb(0x24, 0xcd6);
outb(0x1, 0xcd7);
/* Set LPC decode enables. */
pci_devfn_t dev = PCI_DEV(0, 0x14, 3);
pci_write_config32(dev, 0x44, 0xff03ffd5);
if (CONFIG(POST_DEVICE_PCI_PCIE))
hudson_pci_port80();
if (CONFIG(POST_DEVICE_LPC))
hudson_lpc_port80();
/* enable SIO LPC decode */
byte = pci_read_config8(dev, 0x48);
byte |= 3; /* 2e, 2f */
pci_write_config8(dev, 0x48, byte);
/* enable serial decode */
byte = pci_read_config8(dev, 0x44);
byte |= (1 << 6); /* 0x3f8 */
pci_write_config8(dev, 0x44, byte);
/* run ite */
sbxxx_enable_48mhzout();
ite_conf_clkin(CLKIN_DEV, ITE_UART_CLK_PREDIVIDE_48);
ite_kill_watchdog(GPIO_DEV);
ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
}
void main(unsigned long bist)
{
ite_conf_clkin(CLKIN_DEV, ITE_UART_CLK_PREDIVIDE_24);
ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
report_bist_failure(bist);
enable_smbus();
dump_spd_registers();
sdram_set_registers();
sdram_set_spd_registers();
sdram_enable();
dump_spd_registers();
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr [] = {
// Node 0
DIMM0, DIMM2, 0, 0,
DIMM1, DIMM3, 0, 0,
// Node 1
DIMM4, DIMM6, 0, 0,
DIMM5, DIMM7, 0, 0,
};
struct sys_info *sysinfo = &sysinfo_car;
int needs_reset = 0;
unsigned bsp_apicid = 0;
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
enumerate_ht_chain();
sio_setup();
}
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
#if 0
uint8_t tmp = 0;
pnp_enter_ext_func_mode(SERIAL_DEV);
/* The following line will set CLKIN to 24 MHz, external */
pnp_write_config(SERIAL_DEV, IT8716F_CONFIG_REG_CLOCKSEL, 0x11);
tmp = pnp_read_config(SERIAL_DEV, IT8716F_CONFIG_REG_SWSUSP);
/* Is serial flash enabled? Then enable writing to serial flash. */
if (tmp & 0x0e) {
pnp_write_config(SERIAL_DEV, IT8716F_CONFIG_REG_SWSUSP, tmp | 0x10);
pnp_set_logical_device(GPIO_DEV);
/* Set Serial Flash interface to 0x0820 */
pnp_write_config(GPIO_DEV, 0x64, 0x08);
pnp_write_config(GPIO_DEV, 0x65, 0x20);
}
it8716f_enable_dev(SERIAL_DEV, CONFIG_TTYS0_BASE);
pnp_exit_ext_func_mode(SERIAL_DEV);
#endif
ite_conf_clkin(CLKIN_DEV, ITE_UART_CLK_PREDIVIDE_48);
ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
setup_mb_resource_map();
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\n");
set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
setup_coherent_ht_domain(); // routing table and start other core0
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
// It is said that we should start core1 after all core0 launched
/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
* So here need to make sure last core0 is started, esp for two way system,
* (there may be apic id conflicts in that case)
*/
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
/* it will set up chains and store link pair for optimization later */
ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn
#if CONFIG_SET_FIDVID
{
msr_t msr;
msr=rdmsr(0xc0010042);
print_debug("begin msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
}
enable_fid_change();
enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
init_fidvid_bsp(bsp_apicid);
// show final fid and vid
{
msr_t msr;
msr=rdmsr(0xc0010042);
print_debug("end msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
}
#endif
init_timer(); // Need to use TMICT to synconize FID/VID
needs_reset |= optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
needs_reset |= mcp55_early_setup_x();
// fidvid change will issue one LDTSTOP and the HT change will be effective too
if (needs_reset) {
print_info("ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
//It's the time to set ctrl in sysinfo now;
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
enable_smbus();
/* all ap stopped? */
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
post_cache_as_ram(); // bsp swtich stack to ram and copy sysinfo ram now
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr [] = {
// Node 0
DIMM0, DIMM2, 0, 0,
DIMM1, DIMM3, 0, 0,
// Node 1
DIMM4, DIMM6, 0, 0,
DIMM5, DIMM7, 0, 0,
};
struct sys_info *sysinfo = &sysinfo_car;
int needs_reset = 0;
unsigned bsp_apicid = 0;
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
enumerate_ht_chain();
sio_setup();
}
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
ite_conf_clkin(CLKIN_DEV, ITE_UART_CLK_PREDIVIDE_48);
ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
setup_mb_resource_map();
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
printk(BIOS_DEBUG, "bsp_apicid=%02x\n", bsp_apicid);
set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
setup_coherent_ht_domain(); // routing table and start other core0
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
// It is said that we should start core1 after all core0 launched
/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
* So here need to make sure last core0 is started, esp for two way system,
* (there may be apic id conflicts in that case)
*/
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
/* it will set up chains and store link pair for optimization later */
ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn
#if CONFIG_SET_FIDVID
{
msr_t msr;
msr=rdmsr(0xc0010042);
printk(BIOS_DEBUG, "begin msr fid, vid %08x%08x\n", msr.hi, msr.lo);
}
enable_fid_change();
enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
init_fidvid_bsp(bsp_apicid);
// show final fid and vid
{
msr_t msr;
msr=rdmsr(0xc0010042);
printk(BIOS_DEBUG, "end msr fid, vid %08x%08x\n", msr.hi, msr.lo);
}
#endif
needs_reset |= optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
// fidvid change will issue one LDTSTOP and the HT change will be effective too
if (needs_reset) {
printk(BIOS_INFO, "ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
//It's the time to set ctrl in sysinfo now;
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
sis_init_stage1();
enable_smbus();
//do we need apci timer, tsc...., only debug need it for better output
/* all ap stopped? */
// init_timer(); // Need to use TMICT to synchronize FID/VID
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
sis_init_stage2();
post_cache_as_ram(); // bsp swtich stack to ram and copy sysinfo ram now
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const u16 spd_addr[] = {
DIMM0, DIMM2, 0, 0, /* Channel A (DIMM_A1, DIMM_A2) */
DIMM1, DIMM3, 0, 0, /* Channel B (DIMM_B1, DIMM_B2) */
};
struct sys_info *sysinfo = &sysinfo_car;
int needs_reset = 0;
unsigned bsp_apicid = 0;
if (!cpu_init_detectedx && boot_cpu()) {
/* Allow the HT devices to be found. */
enumerate_ht_chain();
sio_setup();
}
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
ite_conf_clkin(CLKIN_DEV, ITE_UART_CLK_PREDIVIDE_24);
ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
setup_mb_resource_map();
report_bist_failure(bist);
console_init();
printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo, sysinfo + 1);
printk(BIOS_DEBUG, "bsp_apicid=0x%02x\n", bsp_apicid);
/* In BSP so could hold all AP until sysinfo is in RAM. */
set_sysinfo_in_ram(0);
setup_coherent_ht_domain(); /* Routing table and start other core0. */
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
/*
* It is said that we should start core1 after all core0 launched
* becase optimize_link_coherent_ht is moved out from
* setup_coherent_ht_domain, so here need to make sure last core0 is
* started, esp for two way system (there may be APIC ID conflicts in
* that case).
*/
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
/* Set up chains and store link pair for optimization later. */
ht_setup_chains_x(sysinfo); /* Init sblnk and sbbusn, nodes, sbdn. */
/* TODO: FIDVID */
init_timer(); /* Need to use TMICT to synchronize FID/VID. */
needs_reset |= optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
needs_reset |= mcp55_early_setup_x();
/*
* FIDVID change will issue one LDTSTOP and the HT change will be
* effective too.
*/
if (needs_reset) {
printk(BIOS_INFO, "ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
enable_smbus();
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
/* BSP switch stack to RAM and copy sysinfo RAM now. */
post_cache_as_ram();
}
