void board_BeforeAgesa(struct sysinfo *cb) { u8 byte; /* Enable the AcpiMmio space */ outb(0x24, 0xcd6); outb(0x1, 0xcd7); /* Set LPC decode enables. */ pci_devfn_t dev = PCI_DEV(0, 0x14, 3); pci_write_config32(dev, 0x44, 0xff03ffd5); if (CONFIG(POST_DEVICE_PCI_PCIE)) hudson_pci_port80(); if (CONFIG(POST_DEVICE_LPC)) hudson_lpc_port80(); /* enable SIO LPC decode */ byte = pci_read_config8(dev, 0x48); byte |= 3; /* 2e, 2f */ pci_write_config8(dev, 0x48, byte); /* enable serial decode */ byte = pci_read_config8(dev, 0x44); byte |= (1 << 6); /* 0x3f8 */ pci_write_config8(dev, 0x44, byte); /* run ite */ sbxxx_enable_48mhzout(); ite_conf_clkin(CLKIN_DEV, ITE_UART_CLK_PREDIVIDE_48); ite_kill_watchdog(GPIO_DEV); ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE); }
void main(unsigned long bist) { ite_conf_clkin(CLKIN_DEV, ITE_UART_CLK_PREDIVIDE_24); ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE); console_init(); report_bist_failure(bist); enable_smbus(); dump_spd_registers(); sdram_set_registers(); sdram_set_spd_registers(); sdram_enable(); dump_spd_registers(); }
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx) { static const uint16_t spd_addr [] = { // Node 0 DIMM0, DIMM2, 0, 0, DIMM1, DIMM3, 0, 0, // Node 1 DIMM4, DIMM6, 0, 0, DIMM5, DIMM7, 0, 0, }; struct sys_info *sysinfo = &sysinfo_car; int needs_reset = 0; unsigned bsp_apicid = 0; if (!cpu_init_detectedx && boot_cpu()) { /* Nothing special needs to be done to find bus 0 */ /* Allow the HT devices to be found */ enumerate_ht_chain(); sio_setup(); } if (bist == 0) bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo); #if 0 uint8_t tmp = 0; pnp_enter_ext_func_mode(SERIAL_DEV); /* The following line will set CLKIN to 24 MHz, external */ pnp_write_config(SERIAL_DEV, IT8716F_CONFIG_REG_CLOCKSEL, 0x11); tmp = pnp_read_config(SERIAL_DEV, IT8716F_CONFIG_REG_SWSUSP); /* Is serial flash enabled? Then enable writing to serial flash. */ if (tmp & 0x0e) { pnp_write_config(SERIAL_DEV, IT8716F_CONFIG_REG_SWSUSP, tmp | 0x10); pnp_set_logical_device(GPIO_DEV); /* Set Serial Flash interface to 0x0820 */ pnp_write_config(GPIO_DEV, 0x64, 0x08); pnp_write_config(GPIO_DEV, 0x65, 0x20); } it8716f_enable_dev(SERIAL_DEV, CONFIG_TTYS0_BASE); pnp_exit_ext_func_mode(SERIAL_DEV); #endif ite_conf_clkin(CLKIN_DEV, ITE_UART_CLK_PREDIVIDE_48); ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE); setup_mb_resource_map(); console_init(); /* Halt if there was a built in self test failure */ report_bist_failure(bist); printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1); print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\n"); set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram setup_coherent_ht_domain(); // routing table and start other core0 wait_all_core0_started(); #if CONFIG_LOGICAL_CPUS // It is said that we should start core1 after all core0 launched /* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain, * So here need to make sure last core0 is started, esp for two way system, * (there may be apic id conflicts in that case) */ start_other_cores(); wait_all_other_cores_started(bsp_apicid); #endif /* it will set up chains and store link pair for optimization later */ ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn #if CONFIG_SET_FIDVID { msr_t msr; msr=rdmsr(0xc0010042); print_debug("begin msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n"); } enable_fid_change(); enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn); init_fidvid_bsp(bsp_apicid); // show final fid and vid { msr_t msr; msr=rdmsr(0xc0010042); print_debug("end msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n"); } #endif init_timer(); // Need to use TMICT to synconize FID/VID needs_reset |= optimize_link_coherent_ht(); needs_reset |= optimize_link_incoherent_ht(sysinfo); needs_reset |= mcp55_early_setup_x(); // fidvid change will issue one LDTSTOP and the HT change will be effective too if (needs_reset) { print_info("ht reset -\n"); soft_reset(); } allow_all_aps_stop(bsp_apicid); //It's the time to set ctrl in sysinfo now; fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr); enable_smbus(); /* all ap stopped? */ sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo); post_cache_as_ram(); // bsp swtich stack to ram and copy sysinfo ram now }
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx) { static const uint16_t spd_addr [] = { // Node 0 DIMM0, DIMM2, 0, 0, DIMM1, DIMM3, 0, 0, // Node 1 DIMM4, DIMM6, 0, 0, DIMM5, DIMM7, 0, 0, }; struct sys_info *sysinfo = &sysinfo_car; int needs_reset = 0; unsigned bsp_apicid = 0; if (!cpu_init_detectedx && boot_cpu()) { /* Nothing special needs to be done to find bus 0 */ /* Allow the HT devices to be found */ enumerate_ht_chain(); sio_setup(); } if (bist == 0) bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo); ite_conf_clkin(CLKIN_DEV, ITE_UART_CLK_PREDIVIDE_48); ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE); setup_mb_resource_map(); console_init(); /* Halt if there was a built in self test failure */ report_bist_failure(bist); printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1); printk(BIOS_DEBUG, "bsp_apicid=%02x\n", bsp_apicid); set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram setup_coherent_ht_domain(); // routing table and start other core0 wait_all_core0_started(); #if CONFIG_LOGICAL_CPUS // It is said that we should start core1 after all core0 launched /* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain, * So here need to make sure last core0 is started, esp for two way system, * (there may be apic id conflicts in that case) */ start_other_cores(); wait_all_other_cores_started(bsp_apicid); #endif /* it will set up chains and store link pair for optimization later */ ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn #if CONFIG_SET_FIDVID { msr_t msr; msr=rdmsr(0xc0010042); printk(BIOS_DEBUG, "begin msr fid, vid %08x%08x\n", msr.hi, msr.lo); } enable_fid_change(); enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn); init_fidvid_bsp(bsp_apicid); // show final fid and vid { msr_t msr; msr=rdmsr(0xc0010042); printk(BIOS_DEBUG, "end msr fid, vid %08x%08x\n", msr.hi, msr.lo); } #endif needs_reset |= optimize_link_coherent_ht(); needs_reset |= optimize_link_incoherent_ht(sysinfo); // fidvid change will issue one LDTSTOP and the HT change will be effective too if (needs_reset) { printk(BIOS_INFO, "ht reset -\n"); soft_reset(); } allow_all_aps_stop(bsp_apicid); //It's the time to set ctrl in sysinfo now; fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr); sis_init_stage1(); enable_smbus(); //do we need apci timer, tsc...., only debug need it for better output /* all ap stopped? */ // init_timer(); // Need to use TMICT to synchronize FID/VID sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo); sis_init_stage2(); post_cache_as_ram(); // bsp swtich stack to ram and copy sysinfo ram now }
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx) { static const u16 spd_addr[] = { DIMM0, DIMM2, 0, 0, /* Channel A (DIMM_A1, DIMM_A2) */ DIMM1, DIMM3, 0, 0, /* Channel B (DIMM_B1, DIMM_B2) */ }; struct sys_info *sysinfo = &sysinfo_car; int needs_reset = 0; unsigned bsp_apicid = 0; if (!cpu_init_detectedx && boot_cpu()) { /* Allow the HT devices to be found. */ enumerate_ht_chain(); sio_setup(); } if (bist == 0) bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo); ite_conf_clkin(CLKIN_DEV, ITE_UART_CLK_PREDIVIDE_24); ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE); setup_mb_resource_map(); report_bist_failure(bist); console_init(); printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo, sysinfo + 1); printk(BIOS_DEBUG, "bsp_apicid=0x%02x\n", bsp_apicid); /* In BSP so could hold all AP until sysinfo is in RAM. */ set_sysinfo_in_ram(0); setup_coherent_ht_domain(); /* Routing table and start other core0. */ wait_all_core0_started(); #if CONFIG_LOGICAL_CPUS /* * It is said that we should start core1 after all core0 launched * becase optimize_link_coherent_ht is moved out from * setup_coherent_ht_domain, so here need to make sure last core0 is * started, esp for two way system (there may be APIC ID conflicts in * that case). */ start_other_cores(); wait_all_other_cores_started(bsp_apicid); #endif /* Set up chains and store link pair for optimization later. */ ht_setup_chains_x(sysinfo); /* Init sblnk and sbbusn, nodes, sbdn. */ /* TODO: FIDVID */ init_timer(); /* Need to use TMICT to synchronize FID/VID. */ needs_reset |= optimize_link_coherent_ht(); needs_reset |= optimize_link_incoherent_ht(sysinfo); needs_reset |= mcp55_early_setup_x(); /* * FIDVID change will issue one LDTSTOP and the HT change will be * effective too. */ if (needs_reset) { printk(BIOS_INFO, "ht reset -\n"); soft_reset(); } allow_all_aps_stop(bsp_apicid); fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr); enable_smbus(); sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo); /* BSP switch stack to RAM and copy sysinfo RAM now. */ post_cache_as_ram(); }