static int phytec_pfla02_init(void)
{
if (!of_machine_is_compatible("phytec,imx6q-pfla02") &&
!of_machine_is_compatible("phytec,imx6dl-pfla02") &&
!of_machine_is_compatible("phytec,imx6s-pfla02"))
return 0;
phyflex_err006282_workaround();
eth_phy_reset();
phy_register_fixup_for_uid(PHY_ID_KSZ9031, MICREL_PHY_ID_MASK,
ksz9031rn_phy_fixup);
imx6_bbu_nand_register_handler("nand", BBU_HANDLER_FLAG_DEFAULT);
return 0;
}
void board_init_f(ulong dummy)
{
unsigned int ramchip;
struct mx6_ddr_sysinfo sysinfo = {
/* width of data bus:0=16,1=32,2=64 */
.dsize = 2,
/* config for full 4GB range so that get_mem_size() works */
.cs_density = 32, /* 512 MB */
/* single chip select */
#if IS_ENABLED(CONFIG_SPL_DRAM_1_BANK)
.ncs = 1,
#else
.ncs = 2,
#endif
.cs1_mirror = 1,
.rtt_wr = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Wr = RZQ/4 */
.rtt_nom = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Nom = RZQ/4 */
.walat = 1, /* Write additional latency */
.ralat = 5, /* Read additional latency */
.mif3_mode = 3, /* Command prediction working mode */
.bi_on = 1, /* Bank interleaving enabled */
.sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
.rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
.ddr_type = DDR_TYPE_DDR3,
.refsel = 1, /* Refresh cycles at 32KHz */
.refr = 7, /* 8 refresh commands per refresh cycle */
};
#ifdef CONFIG_CMD_NAND
/* Enable NAND */
setup_gpmi_nand();
#endif
/* setup clock gating */
ccgr_init();
/* setup AIPS and disable watchdog */
arch_cpu_init();
/* setup AXI */
gpr_init();
board_early_init_f();
/* setup GP timer */
timer_init();
/* UART clocks enabled and gd valid - init serial console */
preloader_console_init();
setup_spi();
setup_gpios();
/* DDR initialization */
spl_dram_init(&sysinfo, &mt41k_xx[RAM_MT256K]);
ramchip = pfla02_detect_chiptype();
debug("Detected chip %d\n", ramchip);
#if !IS_ENABLED(CONFIG_SPL_DRAM_1_BANK)
switch (ramchip) {
case RAM_MT64K:
sysinfo.cs_density = 6;
break;
case RAM_MT128K:
sysinfo.cs_density = 10;
break;
case RAM_MT256K:
sysinfo.cs_density = 18;
break;
}
#endif
spl_dram_init(&sysinfo, &mt41k_xx[ramchip]);
/* Clear the BSS. */
memset(__bss_start, 0, __bss_end - __bss_start);
phyflex_err006282_workaround();
/* load/boot image from boot device */
board_init_r(NULL, 0);
}
