void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
struct sys_info *sysinfo = &sysinfo_car;
static const u8 spd_addr[] = {RC00, DIMM0, DIMM2, 0, 0, DIMM1, DIMM3, 0, 0, };
u32 bsp_apicid = 0, val;
msr_t msr;
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
/* mov bsp to bus 0xff when > 8 nodes */
set_bsp_node_CHtExtNodeCfgEn();
enumerate_ht_chain();
//enable port80 decoding and southbridge poweron init
sb_Poweron_Init();
}
post_code(0x30);
if (bist == 0) {
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo); /* mmconf is inited in init_cpus */
/* All cores run this but the BSP(node0,core0) is the only core that returns. */
}
post_code(0x32);
enable_rs780_dev8();
sb800_clk_output_48Mhz();
w83627hf_set_clksel_48(PNP_DEV(CONFIG_SIO_PORT, 0));
w83627hf_enable_serial(0, CONFIG_TTYS0_BASE);
uart_init();
console_init();
printk(BIOS_DEBUG, "\n");
// dump_mem(CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE-0x200, CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE);
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
// Load MPB
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
printk(BIOS_DEBUG, "bsp_apicid = %02x \n", bsp_apicid);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
/* Setup sysinfo defaults */
set_sysinfo_in_ram(0);
#if CONFIG_UPDATE_CPU_MICROCODE
update_microcode(val);
#endif
post_code(0x33);
cpuSetAMDMSR();
post_code(0x34);
amd_ht_init(sysinfo);
post_code(0x35);
/* Setup nodes PCI space and start core 0 AP init. */
finalize_node_setup(sysinfo);
/* Setup any mainboard PCI settings etc. */
setup_mb_resource_map();
post_code(0x36);
/* wait for all the APs core0 started by finalize_node_setup. */
/* FIXME: A bunch of cores are going to start output to serial at once.
It would be nice to fixup prink spinlocks for ROM XIP mode.
I think it could be done by putting the spinlock flag in the cache
of the BSP located right after sysinfo.
*/
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
/* Core0 on each node is configured. Now setup any additional cores. */
printk(BIOS_DEBUG, "start_other_cores()\n");
start_other_cores();
post_code(0x37);
wait_all_other_cores_started(bsp_apicid);
#endif
post_code(0x38);
/* run _early_setup before soft-reset. */
rs780_early_setup();
#if CONFIG_SET_FIDVID
msr = rdmsr(0xc0010071);
printk(BIOS_DEBUG, "\nBegin FIDVID MSR 0xc0010071 0x%08x 0x%08x \n", msr.hi, msr.lo);
post_code(0x39);
if (!warm_reset_detect(0)) { // BSP is node 0
init_fidvid_bsp(bsp_apicid, sysinfo->nodes);
} else {
init_fidvid_stage2(bsp_apicid, 0); // BSP is node 0
}
post_code(0x3A);
/* show final fid and vid */
msr=rdmsr(0xc0010071);
printk(BIOS_DEBUG, "End FIDVIDMSR 0xc0010071 0x%08x 0x%08x \n", msr.hi, msr.lo);
#endif
rs780_htinit();
/* Reset for HT, FIDVID, PLL and errata changes to take affect. */
if (!warm_reset_detect(0)) {
print_info("...WARM RESET...\n\n\n");
soft_reset();
die("After soft_reset_x - shouldn't see this message!!!\n");
}
post_code(0x3B);
/* It's the time to set ctrl in sysinfo now; */
printk(BIOS_DEBUG, "fill_mem_ctrl()\n");
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
post_code(0x40);
// die("Die Before MCT init.");
printk(BIOS_DEBUG, "raminit_amdmct()\n");
raminit_amdmct(sysinfo);
post_code(0x41);
/*
dump_pci_device_range(PCI_DEV(0, 0x18, 0), 0, 0x200);
dump_pci_device_range(PCI_DEV(0, 0x18, 1), 0, 0x200);
dump_pci_device_range(PCI_DEV(0, 0x18, 2), 0, 0x200);
dump_pci_device_range(PCI_DEV(0, 0x18, 3), 0, 0x200);
*/
// ram_check(0x00200000, 0x00200000 + (640 * 1024));
// ram_check(0x40200000, 0x40200000 + (640 * 1024));
// die("After MCT init before CAR disabled.");
rs780_before_pci_init();
post_code(0x42);
post_cache_as_ram(); // BSP switch stack to ram, copy then execute LB.
post_code(0x43); // Should never see this post code.
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
post_code(0x30);
agesawrapper_amdinitmmio();
post_code(0x31);
/* Halt if there was a built in self test failure */
post_code(0x33);
report_bist_failure(bist);
sb7xx_51xx_enable_wideio(0, 0x1600); /* though UARTs are on the NUVOTON BMC */
wpcm450_enable_dev(WPCM450_SP1, SIO_PORT, CONFIG_TTYS0_BASE);
sb7xx_51xx_disable_wideio(0);
post_code(0x34);
post_code(0x35);
console_init();
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
post_code(0x37);
val = agesawrapper_amdinitreset();
if (val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitreset failed: %x \n", val);
} else {
printk(BIOS_DEBUG, "agesawrapper_amdinitreset passed\n");
}
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x38);
/*
* SR5650/5670/5690 RD890 chipset, read pci config space hang at POR,
* Disable all Pcie Bridges to work around It.
*/
sr56x0_rd890_disable_pcie_bridge();
post_code(0x39);
nb_Poweron_Init();
post_code(0x3A);
sb_Poweron_Init();
}
post_code(0x3B);
val = agesawrapper_amdinitearly();
if(val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitearly failed: %x \n", val);
} else {
printk(BIOS_DEBUG, "agesawrapper_amdinitearly passed\n");
}
post_code(0x3C);
/* W83627DHG pin89,90 function select is RSTOUT3#, RSTOUT2# by default.
* In order to access W83795G/ADG HWM using I2C protocol,
* we select function to SDA, SCL function (or GP33, GP32 function).
*/
w83627dhg_enable_i2c(PNP_DEV(0x2E, W83627DHG_SPI));
nb_Ht_Init();
post_code(0x3D);
/* Reset for HT, FIDVID, PLL and ucode patch(errata) changes to take affect. */
if (!warm_reset_detect(0)) {
print_info("...WARM RESET...\n\n\n");
distinguish_cpu_resets(0);
soft_reset();
die("After soft_reset_x - shouldn't see this message!!!\n");
}
post_code(0x40);
val = agesawrapper_amdinitpost();
if (val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitpost failed: %x \n", val);
} else {
printk(BIOS_DEBUG, "agesawrapper_amdinitpost passed\n");
}
post_code(0x41);
val = agesawrapper_amdinitenv();
if(val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitenv failed: %x \n", val);
}
printk(BIOS_DEBUG, "agesawrapper_amdinitenv passed\n");
post_code(0x42);
post_code(0x50);
print_debug("Disabling cache as ram ");
disable_cache_as_ram();
print_debug("done\n");
post_code(0x51);
copy_and_run();
/* We will not return, Should never see this message and post code. */
print_debug("should not be here -\n");
post_code(0x54);
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
/* Must come first to enable PCI MMCONF. */
amd_initmmio();
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
sb_Poweron_Init();
post_code(0x31);
winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);
post_code(0x37);
agesawrapper_amdinitreset();
post_code(0x39);
agesawrapper_amdinitearly();
int s3resume = acpi_is_wakeup_s3();
if (!s3resume) {
post_code(0x40);
/* Reboots with outb(3,0x92), outb(4,0xcf9) or triple-fault all
* hang, looks like DRAM re-init goes wrong, don't know why. */
val = agesawrapper_amdinitpost();
if (val == 7) /* fatal, amdinitenv below is going to hang */
outb(0x06, 0x0cf9); /* reset system harder instead */
post_code(0x42);
agesawrapper_amdinitenv();
amd_initenv();
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
agesawrapper_amdinitresume();
agesawrapper_amds3laterestore();
post_code(0x61);
prepare_for_resume();
}
post_code(0x50);
copy_and_run();
printk(BIOS_ERR, "Error: copy_and_run() returned!\n");
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
sb_Poweron_Init();
post_code(0x31);
kbc1100_early_init(CONFIG_SIO_PORT);
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
// Load MPB
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
post_code(0x35);
val = agesawrapper_amdinitmmio();
post_code(0x37);
val = agesawrapper_amdinitreset();
if(val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitreset failed: %x \n", val);
}
post_code(0x38);
printk(BIOS_DEBUG, "Got past sb800_early_setup\n");
post_code(0x39);
val = agesawrapper_amdinitearly ();
if(val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitearly failed: %x \n", val);
}
printk(BIOS_DEBUG, "Got past agesawrapper_amdinitearly\n");
post_code(0x40);
val = agesawrapper_amdinitpost ();
if(val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitpost failed: %x \n", val);
}
printk(BIOS_DEBUG, "Got past agesawrapper_amdinitpost\n");
post_code(0x41);
val = agesawrapper_amdinitenv ();
if(val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitenv failed: %x \n", val);
}
printk(BIOS_DEBUG, "Got past agesawrapper_amdinitenv\n");
/* Initialize i8259 pic */
post_code(0x41);
setup_i8259 ();
/* Initialize i8254 timers */
post_code(0x42);
setup_i8254 ();
post_code(0x50);
copy_and_run(0);
post_code(0x54); // Should never see this post code.
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
/* all cores: allow caching of flash chip code and data
* (there are no cache-as-ram reliability concerns with family 14h)
*/
__writemsr (0x20c, (0x0100000000ull - CACHE_ROM_SIZE) | 5);
__writemsr (0x20d, (0x1000000000ull - CACHE_ROM_SIZE) | 0x800);
/* all cores: set pstate 0 (1600 MHz) early to save a few ms of boot time
*/
__writemsr (0xc0010062, 0);
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
sb_Poweron_Init();
post_code(0x31);
kbc1100_early_init(CONFIG_SIO_PORT);
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
post_code(0x35);
printk(BIOS_DEBUG, "agesawrapper_amdinitmmio ");
val = agesawrapper_amdinitmmio();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
post_code(0x37);
printk(BIOS_DEBUG, "agesawrapper_amdinitreset ");
val = agesawrapper_amdinitreset();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
post_code(0x39);
printk(BIOS_DEBUG, "agesawrapper_amdinitearly ");
val = agesawrapper_amdinitearly();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
post_code(0x40);
printk(BIOS_DEBUG, "agesawrapper_amdinitpost ");
val = agesawrapper_amdinitpost();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
post_code(0x41);
printk(BIOS_DEBUG, "agesawrapper_amdinitenv ");
val = agesawrapper_amdinitenv();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
post_code(0x50);
copy_and_run();
printk(BIOS_ERR, "Error: copy_and_run() returned!\n");
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
#if CONFIG_HAVE_ACPI_RESUME
void *resume_backup_memory;
#endif
/*
* All cores: allow caching of flash chip code and data
* (there are no cache-as-ram reliability concerns with family 14h)
*/
__writemsr (0x20c, (0x0100000000ull - CONFIG_ROM_SIZE) | 5);
__writemsr (0x20d, (0x1000000000ull - CONFIG_ROM_SIZE) | 0x800);
/* All cores: set pstate 0 (1600 MHz) early to save a few ms of boot time */
__writemsr (0xc0010062, 0);
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
sb_Poweron_Init();
post_code(0x31);
f81865f_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
post_code(0x35);
printk(BIOS_DEBUG, "agesawrapper_amdinitmmio ");
val = agesawrapper_amdinitmmio();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
post_code(0x37);
printk(BIOS_DEBUG, "agesawrapper_amdinitreset ");
val = agesawrapper_amdinitreset();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
post_code(0x39);
printk(BIOS_DEBUG, "agesawrapper_amdinitearly ");
val = agesawrapper_amdinitearly ();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
#if CONFIG_HAVE_ACPI_RESUME
if (!acpi_is_wakeup_early()) { /* Check for S3 resume */
#endif
post_code(0x40);
printk(BIOS_DEBUG, "agesawrapper_amdinitpost ");
val = agesawrapper_amdinitpost ();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
post_code(0x42);
printk(BIOS_DEBUG, "agesawrapper_amdinitenv ");
val = agesawrapper_amdinitenv ();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
#if CONFIG_HAVE_ACPI_RESUME
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
printk(BIOS_DEBUG, "agesawrapper_amdinitresume ");
val = agesawrapper_amdinitresume();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
printk(BIOS_DEBUG, "agesawrapper_amds3laterestore ");
val = agesawrapper_amds3laterestore ();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
post_code(0x61);
printk(BIOS_DEBUG, "Find resume memory location\n");
resume_backup_memory = backup_resume();
post_code(0x62);
printk(BIOS_DEBUG, "Move CAR stack.\n");
move_stack_high_mem();
printk(BIOS_DEBUG, "stack moved to: 0x%x\n", (u32) (resume_backup_memory + HIGH_MEMORY_SAVE));
post_code(0x63);
disable_cache_as_ram();
printk(BIOS_DEBUG, "CAR disabled.\n");
set_resume_cache();
/*
* Copy the system memory that is in the ramstage area to the
* reserved area.
*/
if (resume_backup_memory)
memcpy(resume_backup_memory, (void *)(CONFIG_RAMBASE), HIGH_MEMORY_SAVE);
printk(BIOS_DEBUG, "System memory saved. OK to load ramstage.\n");
}
#endif
/* Initialize i8259 pic */
post_code(0x43);
setup_i8259 ();
/* Initialize i8254 timers */
post_code(0x44);
setup_i8254 ();
post_code(0x50);
copy_and_run();
printk(BIOS_ERR, "Error: copy_and_run() returned!\n");
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
/* Must come first to enable PCI MMCONF. */
amd_initmmio();
post_code(0x31);
/* Halt if there was a built in self test failure */
post_code(0x33);
report_bist_failure(bist);
sb7xx_51xx_enable_wideio(0, 0x1600); /* though UARTs are on the NUVOTON BMC */
wpcm450_enable_dev(WPCM450_SP1, 0x164E, CONFIG_TTYS0_BASE);
sb7xx_51xx_disable_wideio(0);
post_code(0x34);
post_code(0x35);
console_init();
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);
post_code(0x37);
agesawrapper_amdinitreset();
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x38);
/*
* SR5650/5670/5690 RD890 chipset, read pci config space hang at POR,
* Disable all Pcie Bridges to work around It.
*/
sr56x0_rd890_disable_pcie_bridge();
post_code(0x39);
nb_Poweron_Init();
post_code(0x3A);
sb_Poweron_Init();
}
post_code(0x3B);
agesawrapper_amdinitearly();
post_code(0x3C);
nb_Ht_Init();
post_code(0x3D);
/* Reset for HT, FIDVID, PLL and ucode patch(errata) changes to take affect. */
if (!warm_reset_detect(0)) {
printk(BIOS_INFO, "...WARM RESET...\n\n\n");
distinguish_cpu_resets(0);
soft_reset();
die("After soft_reset_x - shouldn't see this message!!!\n");
}
post_code(0x40);
agesawrapper_amdinitpost();
post_code(0x41);
agesawrapper_amdinitenv();
post_code(0x42);
post_code(0x50);
printk(BIOS_DEBUG, "Disabling cache as RAM ");
disable_cache_as_ram();
printk(BIOS_DEBUG, "done\n");
post_code(0x51);
copy_and_run();
/* We will not return, Should never see this message and post code. */
printk(BIOS_DEBUG, "should not be here -\n");
post_code(0x54);
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
/*
* All cores: allow caching of flash chip code and data
* (there are no cache-as-ram reliability concerns with family 14h)
*/
__writemsr (0x20c, (0x0100000000ull - CACHE_ROM_SIZE) | 5);
__writemsr (0x20d, (0x1000000000ull - CACHE_ROM_SIZE) | 0x800);
/* All cores: set pstate 0 (1600 MHz) early to save a few ms of boot time */
__writemsr (0xc0010062, 0);
amd_initmmio();
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
sb_Poweron_Init();
post_code(0x31);
fintek_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);
post_code(0x37);
agesawrapper_amdinitreset();
post_code(0x39);
agesawrapper_amdinitearly();
int s3resume = acpi_is_wakeup_s3();
if (!s3resume) {
post_code(0x40);
agesawrapper_amdinitpost();
post_code(0x42);
agesawrapper_amdinitenv();
amd_initenv();
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
agesawrapper_amdinitresume();
agesawrapper_amds3laterestore();
post_code(0x61);
prepare_for_resume();
}
post_code(0x50);
copy_and_run();
printk(BIOS_ERR, "Error: copy_and_run() returned!\n");
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
sch4037_early_init (CONFIG_SIO_PORT);
/* Detect SMSC SIO1036 LPC Debug Card status */
if (detect_sio1036_chip(0x4E)) {
/* Found SMSC SIO1036 LPC Debug Card */
sio1036_early_init(0x4E);
}
post_code(0x31);
console_init();
/*
* SR5650/5670/5690 RD890 chipset, read pci config space hang at POR,
* Disable all Pcie Bridges to work around It.
*/
sr56x0_rd890_disable_pcie_bridge();
}
post_code(0x32);
val = agesawrapper_amdinitmmio();
if (val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitmmio failed: %x \n", val);
} else {
printk(BIOS_DEBUG, "agesawrapper_amdinitmmio passed\n");
}
/* Halt if there was a built in self test failure */
post_code(0x33);
report_bist_failure(bist);
// Load MPB
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
if(boot_cpu()) {
post_code(0x34);
sb_Poweron_Init();
}
post_code(0x35);
val = agesawrapper_amdinitreset();
if (val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitreset failed: %x \n", val);
} else {
printk(BIOS_DEBUG, "agesawrapper_amdinitreset passed\n");
}
post_code(0x36);
val = agesawrapper_amdinitearly ();
if (val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitearly failed: %x \n", val);
} else {
printk(BIOS_DEBUG, "agesawrapper_amdinitearly passed\n");
}
post_code(0x37);
nb_Poweron_Init();
post_code(0x38);
nb_Ht_Init();
post_code(0x39);
val = agesawrapper_amdinitpost ();
if (val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitpost failed: %x \n", val);
} else {
printk(BIOS_DEBUG, "agesawrapper_amdinitpost passed\n");
}
post_code(0x40);
val = agesawrapper_amdinitenv ();
if (val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitenv failed: %x \n", val);
} else {
printk(BIOS_DEBUG, "agesawrapper_amdinitenv passed\n");
}
post_code(0x43);
print_debug("Disabling cache as ram ");
disable_cache_as_ram();
print_debug("done\n");
post_code(0x44);
copy_and_run();
post_code(0x45); // Should never see this post code.
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
amd_initmmio();
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
sch4037_early_init(0x2e);
sio1036_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
post_code(0x31);
console_init();
/*
* SR5650/5670/5690 RD890 chipset, read pci config space hang at POR,
* Disable all Pcie Bridges to work around It.
*/
sr56x0_rd890_disable_pcie_bridge();
}
/* Halt if there was a built in self test failure */
post_code(0x33);
report_bist_failure(bist);
// Load MPB
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);
if(boot_cpu()) {
post_code(0x34);
sb_Poweron_Init();
}
post_code(0x35);
agesawrapper_amdinitreset();
post_code(0x36);
agesawrapper_amdinitearly();
post_code(0x37);
nb_Poweron_Init();
post_code(0x38);
nb_Ht_Init();
post_code(0x39);
agesawrapper_amdinitpost();
post_code(0x40);
agesawrapper_amdinitenv();
post_code(0x43);
printk(BIOS_DEBUG, "Disabling cache as ram ");
disable_cache_as_ram();
printk(BIOS_DEBUG, "done\n");
post_code(0x44);
copy_and_run();
post_code(0x45); // Should never see this post code.
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
msr_t msr;
/*
* All cores: allow caching of flash chip code and data
* (there are no cache-as-ram reliability concerns with family 14h)
*/
msr.lo = ((0x0100000000ull - CACHE_ROM_SIZE) | 5) & 0xFFFFFFFF;
msr.hi = ((0x0100000000ull - CACHE_ROM_SIZE) | 5) >> 32;
wrmsr (MSR_MTRR_VARIABLE_BASE6, msr);
msr.lo = ((0x1000000000ull - CACHE_ROM_SIZE) | 0x800) & 0xFFFFFFFF;
msr.hi = ((0x1000000000ull - CACHE_ROM_SIZE) | 0x800) >> 32;
wrmsr (MSR_MTRR_VARIABLE_MASK6, msr);
/* All cores: set pstate 0 (1600 MHz) early to save a few ms of boot time */
msr.lo = 0;
msr.hi = 0;
wrmsr (MSR_PSTATE_CONTROL, msr);
amd_initmmio();
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
sb_Poweron_Init();
post_code(0x31);
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);
post_code(0x37);
agesawrapper_amdinitreset();
post_code(0x39);
agesawrapper_amdinitearly();
int s3resume = acpi_is_wakeup_s3();
if (!s3resume) {
post_code(0x40);
agesawrapper_amdinitpost();
post_code(0x42);
agesawrapper_amdinitenv();
amd_initenv();
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
agesawrapper_amdinitresume();
agesawrapper_amds3laterestore();
post_code(0x61);
prepare_for_resume();
}
post_code(0x50);
copy_and_run();
printk(BIOS_ERR, "Error: copy_and_run() returned!\n");
post_code(0x54); /* Should never see this post code. */
}