/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
uint16_t addrcmd = 0;
uint16_t comlength = 0;
uint8_t pAddrcmd[CMD_LENGTH] = {0x00};
uint16_t ackbyte = 0x0000;
/* STM32F4xx HAL library initialization:
- Configure the Flash prefetch, instruction and Data caches
- Configure the Systick to generate an interrupt each 1 msec
- Set NVIC Group Priority to 4
- Global MSP (MCU Support Package) initialization
*/
HAL_Init();
/* Configure the system clock to 168 MHz */
SystemClock_Config();
/* Configure LED5 and LED6 */
BSP_LED_Init(LED5);
BSP_LED_Init(LED6);
/*##-1- Configure the SPI peripheral #######################################*/
/* Set the SPI parameters */
SpiHandle.Instance = SPIx;
SpiHandle.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_16;
SpiHandle.Init.Direction = SPI_DIRECTION_2LINES;
SpiHandle.Init.CLKPhase = SPI_PHASE_2EDGE;
SpiHandle.Init.CLKPolarity = SPI_POLARITY_LOW;
SpiHandle.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE;
SpiHandle.Init.CRCPolynomial = 7;
SpiHandle.Init.DataSize = SPI_DATASIZE_8BIT;
SpiHandle.Init.FirstBit = SPI_FIRSTBIT_MSB;
SpiHandle.Init.NSS = SPI_NSS_SOFT;
SpiHandle.Init.TIMode = SPI_TIMODE_DISABLE;
SpiHandle.Init.Mode = SPI_MODE_SLAVE;
if(HAL_SPI_Init(&SpiHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
/* Enter while loop too keep treating new request from Master */
while(1)
{
/* Synchronization between Master and Slave */
Slave_Synchro();
/* Receive command from Master */
if(HAL_SPI_Receive_IT(&SpiHandle, pAddrcmd, CMD_LENGTH) != HAL_OK)
{
Error_Handler();
}
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_SPI_GetState(&SpiHandle) != HAL_SPI_STATE_READY)
{}
/* Compute command and required data length */
addrcmd = (uint16_t) ((pAddrcmd[0] << 8) | pAddrcmd[1]);
comlength = (uint16_t) ((pAddrcmd[2] << 8) | pAddrcmd[3]);
/* Check if received command correct */
if(((addrcmd == ADDRCMD_MASTER_READ) || (addrcmd == ADDRCMD_MASTER_WRITE)) && (comlength > 0))
{
/* Synchronization between Master and Slave */
Slave_Synchro();
/* Send acknowledge to Master */
ackbyte = SPI_ACK_BYTES;
if(HAL_SPI_Transmit_IT(&SpiHandle, (uint8_t *)&ackbyte, sizeof(ackbyte)) != HAL_OK)
{
Error_Handler();
}
while (HAL_SPI_GetState(&SpiHandle) != HAL_SPI_STATE_READY)
{}
/* Check if Master requiring data read or write */
if(addrcmd == ADDRCMD_MASTER_READ)
{
/* Synchronization between Master and Slave */
Slave_Synchro();
/* Send data to Master */
if(HAL_SPI_Transmit_IT(&SpiHandle, aTxSlaveBuffer, DATA_LENGTH) != HAL_OK)
{
Error_Handler();
}
while (HAL_SPI_GetState(&SpiHandle) != HAL_SPI_STATE_READY)
{}
/* Synchronization between Master and Slave */
Slave_Synchro();
/* Receive acknowledgement from Master */
ackbyte = 0;
if(HAL_SPI_Receive_IT(&SpiHandle, (uint8_t *)&ackbyte, sizeof(ackbyte)) != HAL_OK)
{
Error_Handler();
}
while (HAL_SPI_GetState(&SpiHandle) != HAL_SPI_STATE_READY)
{}
/* Check acknowledgement */
if(ackbyte != SPI_ACK_BYTES)
{
Error_Handler();
}
}
else if(addrcmd == ADDRCMD_MASTER_WRITE)
{
/* Synchronization between Master and Slave */
Slave_Synchro();
/* Receive data from Master */
if(HAL_SPI_Receive_IT(&SpiHandle, aRxBuffer, DATA_LENGTH) != HAL_OK)
{
Error_Handler();
}
while (HAL_SPI_GetState(&SpiHandle) != HAL_SPI_STATE_READY)
{}
/* Synchronization between Master and Slave */
Slave_Synchro();
/* Send acknowledgement to Master */
ackbyte = SPI_ACK_BYTES;
if(HAL_SPI_Transmit_IT(&SpiHandle, (uint8_t *)&ackbyte, sizeof(ackbyte)) != HAL_OK)
{
Error_Handler();
}
while (HAL_SPI_GetState(&SpiHandle) != HAL_SPI_STATE_READY)
{}
/* In case, Master has sent data, compare received buffer with one expected */
if(Buffercmp((uint8_t*)aTxMasterBuffer, (uint8_t*)aRxBuffer, DATA_LENGTH))
{
/* Transfer error in transmission process */
Error_Handler();
}
else
{
/* Toggle LED6 on: Reception is correct */
BSP_LED_Toggle(LED6);
}
}
}
else
{
/* Synchronization between Master and Slave */
Slave_Synchro();
/* Send acknowledgement to Master */
ackbyte = SPI_NACK_BYTES;
if(HAL_SPI_Transmit_IT(&SpiHandle, (uint8_t *)&ackbyte, sizeof(ackbyte)) != HAL_OK)
{
Error_Handler();
}
while (HAL_SPI_GetState(&SpiHandle) != HAL_SPI_STATE_READY)
{}
Error_Handler();
}
/* Flush Rx buffer for next transmission */
Flush_Buffer(aRxBuffer, DATA_LENGTH);
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32F3xx HAL library initialization:
- Configure the Flash prefetch
- Configure the Systick to generate an interrupt each 1 msec
- Set NVIC Group Priority to 4
- Low Level Initialization
*/
HAL_Init();
/* Configure LED2 */
BSP_LED_Init(LED2);
/* Configure the system clock to 64 MHz */
SystemClock_Config();
/*##-1- Configure the I2C peripheral ######################################*/
I2cHandle.Instance = I2Cx;
I2cHandle.Init.Timing = I2C_TIMING;
I2cHandle.Init.OwnAddress1 = I2C_ADDRESS;
I2cHandle.Init.AddressingMode = I2C_ADDRESSINGMODE_10BIT;
I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLED;
I2cHandle.Init.OwnAddress2 = 0xFF;
I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLED;
I2cHandle.Init.NoStretchMode = I2C_NOSTRETCH_DISABLED;
if(HAL_I2C_Init(&I2cHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
/* Enable the Analog I2C Filter */
HAL_I2CEx_AnalogFilter_Config(&I2cHandle,I2C_ANALOGFILTER_ENABLED);
#ifdef MASTER_BOARD
/* Configure User push-button */
BSP_PB_Init(BUTTON_USER, BUTTON_MODE_GPIO);
/* Wait for User push-button press before starting the Communication */
while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_RESET)
{
}
/* Wait for User push-button release before starting the Communication */
while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_SET)
{
}
/* The board sends the message and expects to receive it back */
/*##-2- Start the transmission process #####################################*/
/* While the I2C in reception process, user can transmit data through
"aTxBuffer" buffer */
/* Timeout is set to 10S */
while(HAL_I2C_Master_Transmit(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)aTxBuffer, TXBUFFERSIZE, 10000)!= HAL_OK)
{
/* Error_Handler() function is called when Timeout error occurs.
When Acknowledge failure occurs (Slave don't acknowledge its address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
/* Turn LED2 on: Transfer in Transmission process is correct */
BSP_LED_On(LED2);
/* Wait for User push-button press before starting the Communication */
while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_RESET)
{
}
/* Wait for User push-button release before starting the Communication */
while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_SET)
{
}
/*##-3- Put I2C peripheral in reception process ############################*/
/* Timeout is set to 10S */
while(HAL_I2C_Master_Receive(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t *)aRxBuffer, RXBUFFERSIZE, 10000) != HAL_OK)
{
/* Error_Handler() function is called when Timeout error occurs.
When Acknowledge failure occurs (Slave don't acknowledge it's address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
/* Turn LED2 off: Transfer in reception process is correct */
BSP_LED_Off(LED2);
#else
/* The board receives the message and sends it back */
/*##-2- Put I2C peripheral in reception process ############################*/
/* Timeout is set to 10S */
if(HAL_I2C_Slave_Receive(&I2cHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE, 10000) != HAL_OK)
{
/* Transfer error in reception process */
Error_Handler();
}
/* Turn LED2 on: Transfer in reception process is correct */
BSP_LED_On(LED2);
/*##-3- Start the transmission process #####################################*/
/* While the I2C in reception process, user can transmit data through
"aTxBuffer" buffer */
/* Timeout is set to 10S */
if(HAL_I2C_Slave_Transmit(&I2cHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE, 10000)!= HAL_OK)
{
/* Transfer error in transmission process */
Error_Handler();
}
/* Turn LED2 off: Transfer in transmission process is correct */
BSP_LED_Off(LED2);
#endif /* MASTER_BOARD */
/*##-4- Compare the sent and received buffers ##############################*/
if(Buffercmp((uint8_t*)aTxBuffer,(uint8_t*)aRxBuffer,RXBUFFERSIZE))
{
/* Processing Error */
Error_Handler();
}
/* Infinite loop */
while (1)
{
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32F4xx HAL library initialization:
- Configure the Flash prefetch, instruction and Data caches
- Configure the Systick to generate an interrupt each 1 msec
- Set NVIC Group Priority to 4
- Global MSP (MCU Support Package) initialization
*/
HAL_Init();
/* Configure the system clock to 180 MHz */
SystemClock_Config();
/* Configure LED1, LED2, LED3 and LED4 */
BSP_LED_Init(LED1);
BSP_LED_Init(LED2);
BSP_LED_Init(LED3);
BSP_LED_Init(LED4);
/* WAKEUP button (EXTI_Line0) will be used to wakeup the system from STOP mode */
BSP_PB_Init(BUTTON_WAKEUP, BUTTON_MODE_EXTI);
/* Configure Key Button */
BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_GPIO);
/*##-1- Configure the SDRAM device #########################################*/
/* SDRAM device configuration */
BSP_SDRAM_Init();
/*##-2- SDRAM memory write access ##########################################*/
/* Fill the buffer to write */
Fill_Buffer(aTxBuffer, BUFFER_SIZE, 0xA244250F);
/* Write data to the SDRAM memory */
BSP_SDRAM_WriteData(SDRAM_DEVICE_ADDR + WRITE_READ_ADDR, aTxBuffer, BUFFER_SIZE);
/* Wait for TAMPER/KEY to be pushed to enter stop mode */
while(BSP_PB_GetState(BUTTON_TAMPER) != RESET)
{
}
/*##-3- Issue self-refresh command to SDRAM device #########################*/
SDRAMCommandStructure.CommandMode = FMC_SDRAM_CMD_SELFREFRESH_MODE;
SDRAMCommandStructure.CommandTarget = FMC_SDRAM_CMD_TARGET_BANK1;
SDRAMCommandStructure.AutoRefreshNumber = 1;
SDRAMCommandStructure.ModeRegisterDefinition = 0;
if(BSP_SDRAM_Sendcmd(&SDRAMCommandStructure) != HAL_OK)
{
/* Command send Error */
Error_Handler();
}
/*##-4- Enter CPU power stop mode ##########################################*/
/* Put LED4 on to indicate entering to STOP mode */
BSP_LED_On(LED4);
/* Request to enter STOP mode */
HAL_PWR_EnterSTOPMode(PWR_MAINREGULATOR_ON, PWR_STOPENTRY_WFI);
/*##-5- Wakeup CPU from power stop mode ###################################*/
/* Configure the system clock after wakeup from STOP: enable HSE, PLL and select
PLL as system clock source (HSE and PLL are disabled in STOP mode) */
SystemClock_Config();
/*##-6- SDRAM memory read back access ######################################*/
SDRAMCommandStructure.CommandMode = FMC_SDRAM_CMD_NORMAL_MODE;
if(BSP_SDRAM_Sendcmd(&SDRAMCommandStructure) != HAL_OK)
{
/* Command send Error */
Error_Handler();
}
/* Read back data from the SDRAM memory */
BSP_SDRAM_ReadData(SDRAM_DEVICE_ADDR + WRITE_READ_ADDR, aRxBuffer, BUFFER_SIZE);
/*##-7- Checking data integrity ############################################*/
uwWriteReadStatus = Buffercmp(aTxBuffer, aRxBuffer, BUFFER_SIZE);
if (uwWriteReadStatus != PASSED)
{
/* KO */
/* Turn on LED2 */
BSP_LED_On(LED2);
}
else
{
/* OK */
/* Turn on LED1 */
BSP_LED_On(LED1);
}
/* Infinite loop */
while (1)
{
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
#ifdef TRANSMITTER_BOARD
GPIO_InitTypeDef GPIO_InitStruct;
#endif
/* STM32F0xx HAL library initialization:
- Configure the Flash prefetch
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Low Level Initialization
*/
HAL_Init();
/* Configure the system clock to 48 MHz */
SystemClock_Config();
/* Configure LED3 */
BSP_LED_Init(LED3);
#ifdef TRANSMITTER_BOARD
/* Configure PA.12 (Arduino D2) as input with External interrupt */
GPIO_InitStruct.Pin = GPIO_PIN_12;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Mode = GPIO_MODE_IT_RISING;
/* Enable GPIOA clock */
__HAL_RCC_GPIOA_CLK_ENABLE();
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* Enable and set PA.12 (Arduino D2) EXTI Interrupt to the lowest priority */
NVIC_SetPriority((IRQn_Type)(EXTI4_15_IRQn), 0x03);
HAL_NVIC_EnableIRQ((IRQn_Type)(EXTI4_15_IRQn));
/* Wait for the user to set GPIOA to GND before starting the Communication.
In the meantime, LED3 is blinking */
while(VirtualUserButtonStatus == 0)
{
/* Toggle LED3*/
BSP_LED_Toggle(LED3);
HAL_Delay(100);
}
BSP_LED_Off(LED3);
#endif
/*##-1- Configure the UART peripheral ######################################*/
/* Put the USART peripheral in the Asynchronous mode (UART Mode) */
/* UART configured as follows:
- Word Length = 8 Bits
- Stop Bit = One Stop bit
- Parity = None
- BaudRate = 9600 baud
- Hardware flow control disabled (RTS and CTS signals) */
UartHandle.Instance = USARTx;
UartHandle.Init.BaudRate = 9600;
UartHandle.Init.WordLength = UART_WORDLENGTH_8B;
UartHandle.Init.StopBits = UART_STOPBITS_1;
UartHandle.Init.Parity = UART_PARITY_NONE;
UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE;
UartHandle.Init.Mode = UART_MODE_TX_RX;
UartHandle.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;
if(HAL_UART_DeInit(&UartHandle) != HAL_OK)
{
Error_Handler();
}
if(HAL_UART_Init(&UartHandle) != HAL_OK)
{
Error_Handler();
}
#ifdef TRANSMITTER_BOARD
/* The board sends the message and expects to receive it back */
/* DMA is programmed for reception before starting the transmission, in order to
be sure DMA Rx is ready when board 2 will start transmitting */
/*##-2- Program the Reception process #####################################*/
if(HAL_UART_Receive_DMA(&UartHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
{
Error_Handler();
}
/*##-3- Start the transmission process #####################################*/
/* While the UART in reception process, user can transmit data through
"aTxBuffer" buffer */
if(HAL_UART_Transmit_DMA(&UartHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
{
Error_Handler();
}
/*##-4- Wait for the end of the transfer ###################################*/
while (UartReady != SET)
{
}
/* Reset transmission flag */
UartReady = RESET;
#else
/* The board receives the message and sends it back */
/*##-2- Put UART peripheral in reception process ###########################*/
if(HAL_UART_Receive_DMA(&UartHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
{
Error_Handler();
}
/*##-3- Wait for the end of the transfer ###################################*/
/* While waiting for message to come from the other board, LED3 is
blinking according to the following pattern: a double flash every half-second */
while (UartReady != SET)
{
BSP_LED_On(LED3);
HAL_Delay(100);
BSP_LED_Off(LED3);
HAL_Delay(100);
BSP_LED_On(LED3);
HAL_Delay(100);
BSP_LED_Off(LED3);
HAL_Delay(500);
}
/* Reset transmission flag */
UartReady = RESET;
BSP_LED_Off(LED3);
/*##-4- Start the transmission process #####################################*/
/* While the UART in reception process, user can transmit data through
"aTxBuffer" buffer */
if(HAL_UART_Transmit_DMA(&UartHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
{
Error_Handler();
}
#endif /* TRANSMITTER_BOARD */
/*##-5- Wait for the end of the transfer ###################################*/
while (UartReady != SET)
{
}
/* Reset transmission flag */
UartReady = RESET;
/*##-6- Compare the sent and received buffers ##############################*/
if(Buffercmp((uint8_t*)aTxBuffer,(uint8_t*)aRxBuffer,RXBUFFERSIZE))
{
Error_Handler();
}
/* Turn on LED3 if test passes then enter infinite loop */
BSP_LED_On(LED3);
/* Infinite loop */
while (1)
{
}
}
/**
* @brief Main program.
* @param None
* @retval None
*/
int main(void)
{
/* STM32F0xx HAL library initialization:
- Configure the Flash prefetch
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Low Level Initialization
*/
HAL_Init();
/* Configure LED2 */
BSP_LED_Init(LED2);
/* Configure the system clock to 48 MHz */
SystemClock_Config();
/*##-1- Configure the SPI peripheral #######################################*/
/* Set the SPI parameters */
SpiHandle.Instance = SPIx;
SpiHandle.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_256;
SpiHandle.Init.Direction = SPI_DIRECTION_2LINES;
SpiHandle.Init.CLKPhase = SPI_PHASE_1EDGE;
SpiHandle.Init.CLKPolarity = SPI_POLARITY_LOW;
SpiHandle.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLED;
SpiHandle.Init.CRCPolynomial = 7;
SpiHandle.Init.DataSize = SPI_DATASIZE_8BIT;
SpiHandle.Init.FirstBit = SPI_FIRSTBIT_MSB;
SpiHandle.Init.NSS = SPI_NSS_SOFT;
SpiHandle.Init.TIMode = SPI_TIMODE_DISABLED;
SpiHandle.Init.NSSPMode = SPI_NSS_PULSE_DISABLED;
SpiHandle.Init.CRCLength = SPI_CRC_LENGTH_8BIT;
#ifdef MASTER_BOARD
SpiHandle.Init.Mode = SPI_MODE_MASTER;
#else
SpiHandle.Init.Mode = SPI_MODE_SLAVE;
#endif /* MASTER_BOARD */
if(HAL_SPI_Init(&SpiHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
#ifdef MASTER_BOARD
/* Configure User push-button */
BSP_PB_Init(BUTTON_USER, BUTTON_MODE_GPIO);
/* Wait for User push-button press before starting the Communication */
while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_RESET)
{
BSP_LED_Toggle(LED2);
HAL_Delay(100);
}
BSP_LED_Off(LED2);
#endif /* MASTER_BOARD */
/*##-2- Start the Full Duplex Communication process ########################*/
/* While the SPI in TransmitReceive process, user can transmit data through
"aTxBuffer" buffer & receive data through "aRxBuffer" */
/* Timeout is set to 5S */
switch(HAL_SPI_TransmitReceive(&SpiHandle, (uint8_t*)aTxBuffer, (uint8_t *)aRxBuffer, BUFFERSIZE, 5000))
{
case HAL_OK:
/* Communication is completed ___________________________________________ */
/* Compare the sent and received buffers */
if (Buffercmp((uint8_t *)aTxBuffer, (uint8_t *)aRxBuffer, BUFFERSIZE))
{
/* Transfer error in transmission process */
Error_Handler();
}
/* Turn LED2 on: Transfer in transmission/Reception process is correct */
BSP_LED_On(LED2);
break;
case HAL_TIMEOUT:
/* An Error Occur ______________________________________________________ */
case HAL_ERROR:
/* Call Timeout Handler */
Error_Handler();
break;
default:
break;
}
/* Infinite loop */
while (1)
{
}
}
/**
* @brief Main program.
* @param None
* @retval None
*/
int main(void)
{
/* STM32F0xx HAL library initialization:
- Configure the Flash prefetch
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Low Level Initialization
*/
HAL_Init();
/* Configure LED2 */
BSP_LED_Init(LED2);
/* Configure the system clock to 48 MHz */
SystemClock_Config();
/*##-1- Configure the SPI peripheral #######################################*/
/* Set the SPI parameters */
SpiHandle.Instance = SPIx;
SpiHandle.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_256;
SpiHandle.Init.Direction = SPI_DIRECTION_2LINES;
SpiHandle.Init.CLKPhase = SPI_PHASE_1EDGE;
SpiHandle.Init.CLKPolarity = SPI_POLARITY_LOW;
SpiHandle.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE;
SpiHandle.Init.CRCPolynomial = 7;
SpiHandle.Init.DataSize = SPI_DATASIZE_8BIT;
SpiHandle.Init.FirstBit = SPI_FIRSTBIT_MSB;
SpiHandle.Init.NSS = SPI_NSS_SOFT;
SpiHandle.Init.TIMode = SPI_TIMODE_DISABLE;
SpiHandle.Init.NSSPMode = SPI_NSS_PULSE_DISABLE;
SpiHandle.Init.CRCLength = SPI_CRC_LENGTH_8BIT;
#ifdef MASTER_BOARD
SpiHandle.Init.Mode = SPI_MODE_MASTER;
#else
SpiHandle.Init.Mode = SPI_MODE_SLAVE;
#endif /* MASTER_BOARD */
if(HAL_SPI_Init(&SpiHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
#ifdef MASTER_BOARD
/* Configure User push-button */
BSP_PB_Init(BUTTON_USER, BUTTON_MODE_GPIO);
/* Wait for User push-button press before starting the Communication */
while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_RESET)
{
BSP_LED_Toggle(LED2);
HAL_Delay(40);
}
BSP_LED_Off(LED2);
#endif /* MASTER_BOARD */
/*##-2- Start the Full Duplex Communication process ########################*/
/* While the SPI in TransmitReceive process, user can transmit data through
"aTxBuffer" buffer & receive data through "aRxBuffer" */
if(HAL_SPI_TransmitReceive_IT(&SpiHandle, (uint8_t*)aTxBuffer, (uint8_t *)aRxBuffer, BUFFERSIZE) != HAL_OK)
{
/* Transfer error in transmission process */
Error_Handler();
}
/*##-3- Wait for the end of the transfer ###################################*/
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_SPI_GetState(&SpiHandle) != HAL_SPI_STATE_READY)
{
}
/*##-4- Compare the sent and received buffers ##############################*/
if(Buffercmp((uint8_t*)aTxBuffer, (uint8_t*)aRxBuffer, BUFFERSIZE))
{
/* Processing Error */
Error_Handler();
}
/* Infinite loop */
while (1)
{
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32f10x_xx.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32f10x.c file
*/
/* System clocks configuration ---------------------------------------------*/
RCC_Configuration();
/* GPIO configuration ------------------------------------------------------*/
GPIO_Configuration();
/* SPI1 configuration ------------------------------------------------------*/
SPI_InitStructure.SPI_Direction = SPI_Direction_2Lines_FullDuplex;
SPI_InitStructure.SPI_Mode = SPI_Mode_Master;
SPI_InitStructure.SPI_DataSize = SPI_DataSize_16b;
SPI_InitStructure.SPI_CPOL = SPI_CPOL_Low;
SPI_InitStructure.SPI_CPHA = SPI_CPHA_2Edge;
SPI_InitStructure.SPI_NSS = SPI_NSS_Soft;
SPI_InitStructure.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_8;
SPI_InitStructure.SPI_FirstBit = SPI_FirstBit_MSB;
SPI_InitStructure.SPI_CRCPolynomial = 7;
SPI_Init(SPI1, &SPI_InitStructure);
/* SPI2 configuration ------------------------------------------------------*/
SPI_InitStructure.SPI_Mode = SPI_Mode_Slave;
SPI_Init(SPI2, &SPI_InitStructure);
/* Enable SPI1 CRC calculation */
SPI_CalculateCRC(SPI1, ENABLE);
/* Enable SPI2 CRC calculation */
SPI_CalculateCRC(SPI2, ENABLE);
/* Enable SPI1 */
SPI_Cmd(SPI1, ENABLE);
/* Enable SPI2 */
SPI_Cmd(SPI2, ENABLE);
/* Transfer procedure */
while (TxIdx < BufferSize - 1)
{
/* Wait for SPI1 Tx buffer empty */
while (SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_TXE) == RESET);
/* Send SPI2 data */
SPI_I2S_SendData(SPI2, SPI2_Buffer_Tx[TxIdx]);
/* Send SPI1 data */
SPI_I2S_SendData(SPI1, SPI1_Buffer_Tx[TxIdx++]);
/* Wait for SPI2 data reception */
while (SPI_I2S_GetFlagStatus(SPI2, SPI_I2S_FLAG_RXNE) == RESET);
/* Read SPI2 received data */
SPI2_Buffer_Rx[RxIdx] = SPI_I2S_ReceiveData(SPI2);
/* Wait for SPI1 data reception */
while (SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_RXNE) == RESET);
/* Read SPI1 received data */
SPI1_Buffer_Rx[RxIdx++] = SPI_I2S_ReceiveData(SPI1);
}
/* Wait for SPI1 Tx buffer empty */
while (SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_TXE) == RESET);
/* Wait for SPI2 Tx buffer empty */
while (SPI_I2S_GetFlagStatus(SPI2, SPI_I2S_FLAG_TXE) == RESET);
/* Send last SPI2_Buffer_Tx data */
SPI_I2S_SendData(SPI2, SPI2_Buffer_Tx[TxIdx]);
/* Enable SPI2 CRC transmission */
SPI_TransmitCRC(SPI2);
/* Send last SPI1_Buffer_Tx data */
SPI_I2S_SendData(SPI1, SPI1_Buffer_Tx[TxIdx]);
/* Enable SPI1 CRC transmission */
SPI_TransmitCRC(SPI1);
/* Wait for SPI1 last data reception */
while (SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_RXNE) == RESET);
/* Read SPI1 last received data */
SPI1_Buffer_Rx[RxIdx] = SPI_I2S_ReceiveData(SPI1);
/* Wait for SPI2 last data reception */
while (SPI_I2S_GetFlagStatus(SPI2, SPI_I2S_FLAG_RXNE) == RESET);
/* Read SPI2 last received data */
SPI2_Buffer_Rx[RxIdx] = SPI_I2S_ReceiveData(SPI2);
/* Wait for SPI1 data reception: CRC transmitted by SPI2 */
while (SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_RXNE) == RESET);
/* Wait for SPI2 data reception: CRC transmitted by SPI1 */
while (SPI_I2S_GetFlagStatus(SPI2, SPI_I2S_FLAG_RXNE) == RESET);
/* Check the received data with the send ones */
TransferStatus1 = Buffercmp(SPI2_Buffer_Rx, SPI1_Buffer_Tx, BufferSize);
TransferStatus2 = Buffercmp(SPI1_Buffer_Rx, SPI2_Buffer_Tx, BufferSize);
/* TransferStatus1, TransferStatus2 = PASSED, if the data transmitted and received
are correct */
/* TransferStatus1, TransferStatus2 = FAILED, if the data transmitted and received
are different */
/* Test on the SPI1 CRC Error flag */
if ((SPI_I2S_GetFlagStatus(SPI1, SPI_FLAG_CRCERR)) == SET)
{
TransferStatus2 = FAILED;
}
/* Test on the SPI2 CRC Error flag */
if ((SPI_I2S_GetFlagStatus(SPI2, SPI_FLAG_CRCERR)) == SET)
{
TransferStatus1 = FAILED;
}
/* Read SPI1 received CRC value */
CRC1Value = SPI_I2S_ReceiveData(SPI1);
/* Read SPI2 received CRC value */
CRC2Value = SPI_I2S_ReceiveData(SPI2);
while (1)
{}
}
/*******************************************************************************
* Function Name : main
* Description : Main program
* Input : None
* Output : None
* Return : None
*******************************************************************************/
int main(void)
{
#ifdef DEBUG
debug();
#endif
SCU_MCLKSourceConfig(SCU_MCLK_OSC); /*Use OSC as the default clock source*/
SCU_PCLKDivisorConfig(SCU_PCLK_Div1); /* ARM Peripheral bus clokdivisor = 1*/
/* SCU configuration */
SCU_Configuration();
/* GPIO pins configuration */
GPIO_Configuration();
/* VIC configuration */
VIC_Configuration();
/*I2C0 & I2C1 reset */
I2C_DeInit(I2C0);
I2C_DeInit(I2C1);
/* Enable I2C0, I2C1 */
I2C_Cmd(I2C0, ENABLE);
I2C_Cmd(I2C1, ENABLE);
/* Configure GPIO2, I2C0 and I2C1 */
/* I2C0 Configuration */
I2C_Struct.I2C_GeneralCall = I2C_GeneralCall_Disable;
I2C_Struct.I2C_Ack = I2C_Ack_Enable;
I2C_Struct.I2C_CLKSpeed = 400000;
I2C_Struct.I2C_OwnAddress = I2C0OwnAddr;
I2C_Init(I2C0, &I2C_Struct);
/* I2C1 Configuration */
/* we keep the same config as I2C0 for the other I2C_Struct members */
/* We change just the address*/
I2C_Struct.I2C_OwnAddress = I2C1OwnAddr;
I2C_Init(I2C1, &I2C_Struct);
Direction = I2C_MODE_TRANSMITTER;
Fill_Buffer(I2C1_Buffer_Tx, 0x1);
I2C_ITConfig(I2C1, ENABLE);
I2C_ITConfig(I2C0, ENABLE);
I2C_GenerateStart(I2C1, ENABLE);
while (Tx_Idx < BUFFER_SIZE+1);
/* Check if the transmitted data is read correctly */
TransferStatus1 = Buffercmp(I2C0_Buffer_Rx, I2C1_Buffer_Tx, BUFFER_SIZE);
/* TransferStatus = PASSED, if the transmitted from I2C1 and received data
by the I2C0 are the same */
/* TransferStatus = FAILED, if the transmitted from I2C1 and received data
by the I2C0 are different */
/*--------------------------------------------------*/
/* Delay between transmission and reception --------*/
/*--------------------------------------------------*/
Delay(100000);
/*--------------------------------------------------*/
/* Reception Phase----------------------------------*/
/*--------------------------------------------------*/
/*reset counters*/
Tx_Idx = Rx_Idx = 0;
Direction = I2C_MODE_RECEIVER;
Fill_Buffer(I2C0_Buffer_Tx, 0x5);
I2C_GenerateStart(I2C1, ENABLE);
while (Tx_Idx < BUFFER_SIZE+1);
/* Check if the transmitted data is read correctly */
TransferStatus2 = Buffercmp(I2C1_Buffer_Rx, I2C0_Buffer_Tx, BUFFER_SIZE);
/* TransferStatus = PASSED, if the transmitted from I2C0 and received data
by the I2C1 are the same */
/* TransferStatus = FAILED, if the transmitted from I2C0 and received data
by the I2C1 are different */
while(1);
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32f2xx.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32f2xx.c file
*/
/* I2C configuration ---------------------------------------------------------*/
I2C_Config();
/* Initialize LEDs mounted on STM322xG-EVAL board */
STM_EVAL_LEDInit(LED1);
STM_EVAL_LEDInit(LED2);
STM_EVAL_LEDInit(LED3);
STM_EVAL_LEDInit(LED4);
/* SysTick configuration -----------------------------------------------------*/
SysTickConfig();
/* Clear the RxBuffer */
Fill_Buffer(RxBuffer, RXBUFFERSIZE);
/*************************************Master Code******************************/
#if defined (I2C_MASTER)
/* I2C Struct Initialize */
I2C_InitStructure.I2C_Mode = I2C_Mode_I2C;
I2C_InitStructure.I2C_DutyCycle = I2C_DUTYCYCLE;
I2C_InitStructure.I2C_OwnAddress1 = 0xA0;
I2C_InitStructure.I2C_Ack = I2C_Ack_Enable;
I2C_InitStructure.I2C_ClockSpeed = I2C_SPEED;
#ifndef I2C_10BITS_ADDRESS
I2C_InitStructure.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit;
#else
I2C_InitStructure.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_10bit;
#endif /* I2C_10BITS_ADDRESS */
/* I2C Initialize */
I2C_Init(I2Cx, &I2C_InitStructure);
/* Master Transmitter --------------------------------------------------------*/
/* Generate the Start condition */
I2C_GenerateSTART(I2Cx, ENABLE);
#ifdef I2C_10BITS_ADDRESS
/* Test on I2C1 EV5 and clear it */
TimeOut = USER_TIMEOUT;
while ((!I2C_CheckEvent(I2Cx, I2C_EVENT_MASTER_MODE_SELECT))&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Send Header to I2Cx for write or time out */
I2C_SendData(I2Cx, HEADER_ADDRESS_Write);
/* Test on I2Cx EV9 and clear it */
TimeOut = USER_TIMEOUT;
while ((!I2C_CheckEvent(I2Cx, I2C_EVENT_MASTER_MODE_ADDRESS10))&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Send I2Cx slave Address for write */
I2C_Send7bitAddress(I2Cx, (uint8_t)SLAVE_ADDRESS, I2C_Direction_Transmitter);
#else /* I2C_7BITS_ADDRESS */
/* Test on I2Cx EV5 and clear it or time out */
TimeOut = USER_TIMEOUT;
while ((!I2C_CheckEvent(I2Cx, I2C_EVENT_MASTER_MODE_SELECT))&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Send I2Cx slave Address for write */
I2C_Send7bitAddress(I2Cx, SLAVE_ADDRESS, I2C_Direction_Transmitter);
#endif /* I2C_10BITS_ADDRESS */
/* Test on I2Cx EV6 and clear it or time out */
TimeOut = USER_TIMEOUT;
while ((!I2C_CheckEvent(I2Cx, I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED))&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* I2Cx DMA Enable */
I2C_DMACmd(I2Cx, ENABLE);
/* Enable DMA TX Channel */
DMA_Cmd(I2Cx_DMA_STREAM_TX, ENABLE);
/* Wait until I2Cx_DMA_STREAM_TX enabled or time out */
TimeOut = USER_TIMEOUT;
while ((DMA_GetCmdStatus(I2Cx_DMA_STREAM_TX)!= ENABLE)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Wait until DMA Transfer Complete or time out */
TimeOut = USER_TIMEOUT;
while ((DMA_GetFlagStatus(I2Cx_DMA_STREAM_TX,I2Cx_TX_DMA_TCFLAG) == RESET)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* I2Cx DMA Disable */
I2C_DMACmd(I2Cx, DISABLE);
/* Wait until BTF Flag is set before generating STOP or time out */
TimeOut = USER_TIMEOUT;
while ((!I2C_GetFlagStatus(I2Cx,I2C_FLAG_BTF))&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Send I2Cx STOP Condition */
I2C_GenerateSTOP(I2Cx, ENABLE);
/* Disable DMA TX Channel */
DMA_Cmd(I2Cx_DMA_STREAM_TX, DISABLE);
/* Wait until I2Cx_DMA_STREAM_TX disabled or time out */
TimeOut = USER_TIMEOUT;
while ((DMA_GetCmdStatus(I2Cx_DMA_STREAM_TX)!= DISABLE)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Clear any pending flag on Tx Stream */
DMA_ClearFlag(I2Cx_DMA_STREAM_TX, I2Cx_TX_DMA_TCFLAG | I2Cx_TX_DMA_FEIFLAG | I2Cx_TX_DMA_DMEIFLAG | \
I2Cx_TX_DMA_TEIFLAG | I2Cx_TX_DMA_HTIFLAG);
/* Master Receiver -----------------------------------------------------------*/
/* Enable DMA NACK automatic generation */
I2C_DMALastTransferCmd(I2Cx, ENABLE);
/* Send I2Cx START condition */
I2C_GenerateSTART(I2Cx, ENABLE);
#ifdef I2C_10BITS_ADDRESS
/* Test on EV5 and clear it or time out */
TimeOut = USER_TIMEOUT;
while ((!I2C_CheckEvent(I2Cx, I2C_EVENT_MASTER_MODE_SELECT))&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Send Header to Slave for write */
I2C_SendData(I2Cx, HEADER_ADDRESS_Write);
/* Test on EV9 and clear it or time out */
TimeOut = USER_TIMEOUT;
while ((!I2C_CheckEvent(I2Cx, I2C_EVENT_MASTER_MODE_ADDRESS10))&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Send slave Address */
I2C_Send7bitAddress(I2Cx, (uint8_t)SLAVE_ADDRESS, I2C_Direction_Transmitter);
/* Test on I2Cx EV6 and clear it or time out*/
TimeOut = USER_TIMEOUT;
while ((!I2C_CheckEvent(I2Cx, I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED))&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Repeated Start */
I2C_GenerateSTART(I2Cx, ENABLE);
/* Test on EV5 and clear it or time out*/
TimeOut = USER_TIMEOUT;
while ((!I2C_CheckEvent(I2Cx, I2C_EVENT_MASTER_MODE_SELECT))&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Send Header to Slave for Read */
I2C_SendData(I2Cx, HEADER_ADDRESS_Read);
#else /* I2C_7BITS_ADDRESS */
/* Test on I2Cx EV5 and clear it or time out*/
TimeOut = USER_TIMEOUT;
while ((!I2C_CheckEvent(I2Cx, I2C_EVENT_MASTER_MODE_SELECT))&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Send I2Cx slave Address for write */
I2C_Send7bitAddress(I2Cx, SLAVE_ADDRESS, I2C_Direction_Receiver);
#endif /* I2C_10BITS_ADDRESS */
/* Test on I2Cx EV6 and clear it or time out */
TimeOut = USER_TIMEOUT;
while ((!I2C_CheckEvent(I2Cx, I2C_EVENT_MASTER_RECEIVER_MODE_SELECTED))&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* I2Cx DMA Enable */
I2C_DMACmd(I2Cx, ENABLE);
/* Enable DMA RX Channel */
DMA_Cmd(I2Cx_DMA_STREAM_RX, ENABLE);
/* Wait until I2Cx_DMA_STREAM_RX enabled or time out */
TimeOut = USER_TIMEOUT;
while ((DMA_GetCmdStatus(I2Cx_DMA_STREAM_RX)!= ENABLE)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Transfer complete or time out */
TimeOut = USER_TIMEOUT;
while ((DMA_GetFlagStatus(I2Cx_DMA_STREAM_RX,I2Cx_RX_DMA_TCFLAG)==RESET)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Send I2Cx STOP Condition */
I2C_GenerateSTOP(I2Cx, ENABLE);
/* Disable DMA RX Channel */
DMA_Cmd(I2Cx_DMA_STREAM_RX, DISABLE);
/* Wait until I2Cx_DMA_STREAM_RX disabled or time out */
TimeOut = USER_TIMEOUT;
while ((DMA_GetCmdStatus(I2Cx_DMA_STREAM_RX)!= DISABLE)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Disable I2C DMA request */
I2C_DMACmd(I2Cx,DISABLE);
/* Clear any pending flag on Rx Stream */
DMA_ClearFlag(I2Cx_DMA_STREAM_RX, I2Cx_RX_DMA_TCFLAG | I2Cx_RX_DMA_FEIFLAG | I2Cx_RX_DMA_DMEIFLAG | \
I2Cx_RX_DMA_TEIFLAG | I2Cx_RX_DMA_HTIFLAG);
if (Buffercmp(TxBuffer, RxBuffer, RXBUFFERSIZE) == PASSED)
{
/* LED2, LED3 and LED4 Toggle */
STM_EVAL_LEDOn(LED2);
STM_EVAL_LEDOn(LED3);
STM_EVAL_LEDOn(LED4);
}
else
{ /* ED2, LED3 and LED4 On */
STM_EVAL_LEDOff(LED2);
STM_EVAL_LEDOff(LED3);
STM_EVAL_LEDOff(LED4);
}
#endif /* I2C_MASTER */
/**********************************Slave Code**********************************/
#if defined (I2C_SLAVE)
/* Initialize I2C peripheral */
/* I2C Init */
I2C_InitStructure.I2C_Mode = I2C_Mode_I2C;
I2C_InitStructure.I2C_DutyCycle = I2C_DUTYCYCLE;
I2C_InitStructure.I2C_OwnAddress1 = SLAVE_ADDRESS;
I2C_InitStructure.I2C_Ack = I2C_Ack_Enable;
I2C_InitStructure.I2C_ClockSpeed = I2C_SPEED;
#ifndef I2C_10BITS_ADDRESS
I2C_InitStructure.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit;
#else
I2C_InitStructure.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_10bit;
#endif /* I2C_10BITS_ADDRESS */
I2C_Init(I2Cx, &I2C_InitStructure);
/* Slave Receiver ------------------------------------------------------------*/
/* Test on I2C EV1 and clear it */
while (!I2C_CheckEvent(I2Cx, I2C_EVENT_SLAVE_RECEIVER_ADDRESS_MATCHED))
{}
/* I2Cx DMA Enable */
I2C_DMACmd(I2Cx, ENABLE);
/* Enable DMA RX Channel */
DMA_Cmd(I2Cx_DMA_STREAM_RX, ENABLE);
/* Wait until I2Cx_DMA_STREAM_RX enabled or time out */
TimeOut = USER_TIMEOUT;
while ((DMA_GetCmdStatus(I2Cx_DMA_STREAM_RX)!= ENABLE)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Transfer complete or time out */
TimeOut = USER_TIMEOUT;
while ((DMA_GetFlagStatus(I2Cx_DMA_STREAM_RX,I2Cx_RX_DMA_TCFLAG)==RESET)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Test on I2Cx EV4 and clear it or time out */
TimeOut = USER_TIMEOUT;
while ((!I2C_CheckEvent(I2Cx, I2C_EVENT_SLAVE_STOP_DETECTED))&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Disable DMA RX Channel */
DMA_Cmd(I2Cx_DMA_STREAM_RX, DISABLE);
/* Wait until I2Cx_DMA_STREAM_RX disabled or time out */
TimeOut = USER_TIMEOUT;
while ((DMA_GetCmdStatus(I2Cx_DMA_STREAM_RX)!= DISABLE)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Disable I2C DMA request */
I2C_DMACmd(I2Cx,DISABLE);
/* Clear any pending flag on Rx Stream */
DMA_ClearFlag(I2Cx_DMA_STREAM_RX, I2Cx_RX_DMA_TCFLAG | I2Cx_RX_DMA_FEIFLAG | I2Cx_RX_DMA_DMEIFLAG | \
I2Cx_RX_DMA_TEIFLAG | I2Cx_RX_DMA_HTIFLAG);
/* Slave Transmitter ---------------------------------------------------------*/
/* Test on I2C EV1 and clear it or time out*/
while (!I2C_CheckEvent(I2Cx, I2C_EVENT_SLAVE_TRANSMITTER_ADDRESS_MATCHED))
{}
/* I2Cx DMA Enable */
I2C_DMACmd(I2Cx, ENABLE);
/* Enable DMA RX Channel */
DMA_Cmd(I2Cx_DMA_STREAM_TX, ENABLE);
/* Wait until I2Cx_DMA_STREAM_TX enabled or time out */
TimeOut = USER_TIMEOUT;
while ((DMA_GetCmdStatus(I2Cx_DMA_STREAM_TX)!= ENABLE)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Transfer complete or time out */
TimeOut = USER_TIMEOUT;
while ((DMA_GetFlagStatus(I2Cx_DMA_STREAM_TX,I2Cx_TX_DMA_TCFLAG)==RESET)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Test on I2Cx EV3-2 and clear it or time out */
TimeOut = USER_TIMEOUT;
while ((!I2C_CheckEvent(I2Cx, I2C_EVENT_SLAVE_ACK_FAILURE))&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Disable DMA TX Channel */
DMA_Cmd(I2Cx_DMA_STREAM_TX, DISABLE);
/* Wait until I2Cx_DMA_STREAM_TX disabled or time out */
TimeOut = USER_TIMEOUT;
while ((DMA_GetCmdStatus(I2Cx_DMA_STREAM_TX)!= DISABLE)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Disable I2C DMA request */
I2C_DMACmd(I2Cx,DISABLE);
/* Clear any pending flag on Tx Stream */
DMA_ClearFlag(I2Cx_DMA_STREAM_TX, I2Cx_TX_DMA_TCFLAG | I2Cx_TX_DMA_FEIFLAG | I2Cx_TX_DMA_DMEIFLAG | \
I2Cx_TX_DMA_TEIFLAG | I2Cx_TX_DMA_HTIFLAG);
if (Buffercmp(TxBuffer, RxBuffer, RXBUFFERSIZE) == PASSED)
{
/* LED2, LED3 and LED4 are On */
STM_EVAL_LEDOn(LED2);
STM_EVAL_LEDOn(LED3);
STM_EVAL_LEDOn(LED4);
}
else
{ /* LED2, LED3 and LED4 are Off */
STM_EVAL_LEDOff(LED2);
STM_EVAL_LEDOff(LED3);
STM_EVAL_LEDOff(LED4);
}
#endif /* I2C_SLAVE */
while(1)
{}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32F4xx HAL library initialization:
- Configure the Flash prefetch, instruction and Data caches
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Set NVIC Group Priority to 4
- Low Level Initialization: global MSP (MCU Support Package) initialization
*/
HAL_Init();
/* Configure the system clock to 180 MHz */
SystemClock_Config();
/* Configure LED1, LED2, LED3 and LED4 */
BSP_LED_Init(LED1);
BSP_LED_Init(LED2);
BSP_LED_Init(LED3);
BSP_LED_Init(LED4);
/*##-1- Configure the UART peripheral ######################################*/
/* Put the USART peripheral in the Asynchronous mode (UART Mode) */
/* UART configured as follows:
- Word Length = 8 Bits
- Stop Bit = One Stop bit
- Parity = None
- BaudRate = 9600 baud
- Hardware flow control disabled (RTS and CTS signals) */
UartHandle.Instance = USARTx;
UartHandle.Init.BaudRate = 9600;
UartHandle.Init.WordLength = UART_WORDLENGTH_8B;
UartHandle.Init.StopBits = UART_STOPBITS_1;
UartHandle.Init.Parity = UART_PARITY_NONE;
UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE;
UartHandle.Init.Mode = UART_MODE_TX_RX;
if(HAL_UART_DeInit(&UartHandle) != HAL_OK)
{
Error_Handler();
}
if(HAL_UART_Init(&UartHandle) != HAL_OK)
{
Error_Handler();
}
#ifdef TRANSMITTER_BOARD
/* Configure User push-button in Interrupt mode */
BSP_PB_Init(BUTTON_USER, BUTTON_MODE_EXTI);
/* Wait for User push-button press before starting the Communication.
In the meantime, LED2 is blinking */
while(UserButtonStatus == 0)
{
/* Toggle LED2*/
BSP_LED_Toggle(LED2);
HAL_Delay(100);
}
BSP_LED_Off(LED2);
/* The board sends the message and expects to receive it back */
/*##-2- Start the transmission process #####################################*/
/* While the UART in reception process, user can transmit data through
"aTxBuffer" buffer */
if(HAL_UART_Transmit_DMA(&UartHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
{
Error_Handler();
}
/*##-3- Wait for the end of the transfer ###################################*/
while (UartReady != SET)
{
}
/* Reset transmission flag */
UartReady = RESET;
/*##-4- Put UART peripheral in reception process ###########################*/
if(HAL_UART_DeInit(&UartHandle) != HAL_OK)
{
Error_Handler();
}
if(HAL_UART_Init(&UartHandle) != HAL_OK)
{
Error_Handler();
}
if(HAL_UART_Receive_DMA(&UartHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
{
Error_Handler();
}
#else
/* The board receives the message and sends it back */
/*##-2- Put UART peripheral in reception process ###########################*/
if(HAL_UART_Receive_DMA(&UartHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
{
Error_Handler();
}
/*##-3- Wait for the end of the transfer ###################################*/
/* While waiting for message to come from the other board, LED2 is
blinking according to the following pattern: a double flash every half-second */
while (UartReady != SET)
{
BSP_LED_On(LED2);
HAL_Delay(100);
BSP_LED_Off(LED2);
HAL_Delay(100);
BSP_LED_On(LED2);
HAL_Delay(100);
BSP_LED_Off(LED2);
HAL_Delay(500);
}
/* Reset transmission flag */
UartReady = RESET;
BSP_LED_Off(LED2);
/*##-4- Start the transmission process #####################################*/
/* While the UART in reception process, user can transmit data through
"aTxBuffer" buffer */
if(HAL_UART_DeInit(&UartHandle) != HAL_OK)
{
Error_Handler();
}
if(HAL_UART_Init(&UartHandle) != HAL_OK)
{
Error_Handler();
}
if(HAL_UART_Transmit_DMA(&UartHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
{
Error_Handler();
}
#endif /* TRANSMITTER_BOARD */
/*##-5- Wait for the end of the transfer ###################################*/
while (UartReady != SET)
{
}
/* Reset transmission flag */
UartReady = RESET;
/*##-6- Compare the sent and received buffers ##############################*/
if(Buffercmp((uint8_t*)aTxBuffer,(uint8_t*)aRxBuffer,RXBUFFERSIZE))
{
Error_Handler();
}
/* Infinite loop */
while (1)
{
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32F103xB HAL library initialization:
- Configure the Flash prefetch
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Set NVIC Group Priority to 4
- Low Level Initialization
*/
HAL_Init();
/* Configure the system clock to 64 MHz */
SystemClock_Config();
/* Configure LED2, LED2 and LED2 */
BSP_LED_Init(LED2);
/*##-1- Configure the SPI peripheral #######################################*/
/* Set the SPI parameters */
SpiHandle.Instance = SPIx;
SpiHandle.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_32;
SpiHandle.Init.Direction = SPI_DIRECTION_2LINES;
SpiHandle.Init.CLKPhase = SPI_PHASE_1EDGE;
SpiHandle.Init.CLKPolarity = SPI_POLARITY_LOW;
SpiHandle.Init.DataSize = SPI_DATASIZE_8BIT;
SpiHandle.Init.FirstBit = SPI_FIRSTBIT_MSB;
SpiHandle.Init.TIMode = SPI_TIMODE_DISABLE;
SpiHandle.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE;
SpiHandle.Init.CRCPolynomial = 7;
SpiHandle.Init.NSS = SPI_NSS_SOFT;
#ifdef MASTER_BOARD
SpiHandle.Init.Mode = SPI_MODE_MASTER;
#else
SpiHandle.Init.Mode = SPI_MODE_SLAVE;
#endif /* MASTER_BOARD */
if(HAL_SPI_Init(&SpiHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
#ifdef MASTER_BOARD
/* SPI block is enabled prior calling SPI transmit/receive functions, in order to get CLK signal properly pulled down.
Otherwise, SPI CLK signal is not clean on this board and leads to errors during transfer */
__HAL_SPI_ENABLE(&SpiHandle);
/* Configure User push-button */
BSP_PB_Init(BUTTON_USER, BUTTON_MODE_GPIO);
/* Wait for User push-button press before starting the Communication */
while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_RESET)
{
BSP_LED_Toggle(LED2);
HAL_Delay(100);
}
BSP_LED_Off(LED2);
#endif /* MASTER_BOARD */
/*##-2- Start the Full Duplex Communication process ########################*/
/* While the SPI in TransmitReceive process, user can transmit data through
"aTxBuffer" buffer & receive data through "aRxBuffer" */
if(HAL_SPI_TransmitReceive_DMA(&SpiHandle, (uint8_t*)aTxBuffer, (uint8_t *)aRxBuffer, BUFFERSIZE) != HAL_OK)
{
/* Transfer error in transmission process */
Error_Handler();
}
/*##-3- Wait for the end of the transfer ###################################*/
/* Before starting a new communication transfer, you must wait the callback call
to get the transfer complete confirmation or an error detection.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (wTransferState == TRANSFER_WAIT)
{
}
switch(wTransferState)
{
case TRANSFER_COMPLETE :
/*##-4- Compare the sent and received buffers ##############################*/
if(Buffercmp((uint8_t*)aTxBuffer, (uint8_t*)aRxBuffer, BUFFERSIZE))
{
/* Processing Error */
Error_Handler();
}
break;
default :
Error_Handler();
break;
}
/* Infinite loop */
while (1)
{
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32F4xx HAL library initialization:
- Configure the Flash prefetch, instruction and Data caches
- Configure the Systick to generate an interrupt each 1 msec
- Set NVIC Group Priority to 4
- Global MSP (MCU Support Package) initialization
*/
HAL_Init();
/* Configure LED3, LED4, LED5 and LED6 */
BSP_LED_Init(LED3);
BSP_LED_Init(LED4);
BSP_LED_Init(LED5);
BSP_LED_Init(LED6);
/* Configure the system clock to 84 MHz */
SystemClock_Config();
/*##-1- Configure the SPI peripheral #######################################*/
/* Set the SPI parameters */
SpiHandle.Instance = SPIx;
SpiHandle.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_32;
SpiHandle.Init.Direction = SPI_DIRECTION_2LINES;
SpiHandle.Init.CLKPhase = SPI_PHASE_1EDGE;
SpiHandle.Init.CLKPolarity = SPI_POLARITY_HIGH;
SpiHandle.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE;
SpiHandle.Init.CRCPolynomial = 7;
SpiHandle.Init.DataSize = SPI_DATASIZE_8BIT;
SpiHandle.Init.FirstBit = SPI_FIRSTBIT_MSB;
SpiHandle.Init.NSS = SPI_NSS_SOFT;
SpiHandle.Init.TIMode = SPI_TIMODE_DISABLE;
#ifdef MASTER_BOARD
SpiHandle.Init.Mode = SPI_MODE_MASTER;
#else
SpiHandle.Init.Mode = SPI_MODE_SLAVE;
#endif /* MASTER_BOARD */
if(HAL_SPI_Init(&SpiHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
#ifdef MASTER_BOARD
/* Configure Tamper push button */
BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_GPIO);
/* Wait for Tamper Button press before starting the Communication */
while (BSP_PB_GetState(BUTTON_KEY) != 1)
{
BSP_LED_Toggle(LED3);
HAL_Delay(40);
}
BSP_LED_Off(LED3);
#endif /* MASTER_BOARD */
/*##-2- Start the Full Duplex Communication process ########################*/
/* While the SPI in TransmitReceive process, user can transmit data through
"aTxBuffer" buffer & receive data through "aRxBuffer" */
if(HAL_SPI_TransmitReceive_DMA(&SpiHandle, (uint8_t*)aTxBuffer, (uint8_t *)aRxBuffer, BUFFERSIZE) != HAL_OK)
{
/* Transfer error in transmission process */
Error_Handler();
}
/*##-3- Wait for the end of the transfer ###################################*/
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_SPI_GetState(&SpiHandle) != HAL_SPI_STATE_READY)
{
}
/*##-4- Compare the sent and received buffers ##############################*/
if(Buffercmp((uint8_t*)aTxBuffer, (uint8_t*)aRxBuffer, BUFFERSIZE))
{
/* Transfer error in transmission process */
Error_Handler();
}
/* Infinite loop */
while (1)
{
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32l1xx_xx.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32l1xx.c file
*/
#ifdef ENABLE_LCD_MSG_DISPLAY
/* Initialize the LCD screen for information display */
#ifdef USE_STM32L152D_EVAL
STM32L152D_LCD_Init();
#else
STM32L152_LCD_Init();
#endif
LCD_Clear(LCD_COLOR_BLUE);
LCD_SetBackColor(LCD_COLOR_BLUE);
LCD_SetTextColor(LCD_COLOR_WHITE);
LCD_DisplayStringLine(LCD_LINE_0, "SMT32L1xx FW Library");
LCD_DisplayStringLine(LCD_LINE_1, " EEPROM Example ");
#endif /* ENABLE_LCD_MSG_DISPLAY */
/* Initialize the I2C EEPROM driver ----------------------------------------*/
sEE_Init();
/* First write in the memory followed by a read of the written data --------*/
/* Write on I2C EEPROM from sEE_WRITE_ADDRESS1 */
sEE_WriteBuffer(Tx1_Buffer, sEE_WRITE_ADDRESS1, BUFFER_SIZE1);
/* Wait for EEPROM standby state */
sEE_WaitEepromStandbyState();
/* Set the Number of data to be read */
NumDataRead = BUFFER_SIZE1;
/* Read from I2C EEPROM from sEE_READ_ADDRESS1 */
sEE_ReadBuffer(Rx1_Buffer, sEE_READ_ADDRESS1, (uint16_t *)(&NumDataRead));
/* Starting from this point, if the requested number of data is higher than 1,
then only the DMA is managing the data transfer. Meanwhile, CPU is free to
perform other tasks:
// Add your code here:
//...
//...
For simplicity reasons, this example is just waiting till the end of the
transfer. */
#ifdef ENABLE_LCD_MSG_DISPLAY
LCD_DisplayStringLine(LCD_LINE_3, " Transfer 1 Ongoing ");
#endif /* ENABLE_LCD_MSG_DISPLAY */
/* Wait till DMA transfer is compelete (Tranfer complete interrupt handler
resets the variable holding the number of data to be read) */
while (NumDataRead > 0)
{}
/* Check if the data written to the memory is read correctly */
TransferStatus1 = Buffercmp(Tx1_Buffer, Rx1_Buffer, BUFFER_SIZE1);
/* TransferStatus1 = PASSED, if the transmitted and received data
to/from the EEPROM are the same */
/* TransferStatus1 = FAILED, if the transmitted and received data
to/from the EEPROM are different */
#ifdef ENABLE_LCD_MSG_DISPLAY
if (TransferStatus1 == PASSED)
{
LCD_DisplayStringLine(LCD_LINE_3, " Transfer 1 PASSED ");
}
else
{
LCD_DisplayStringLine(LCD_LINE_3, " Transfer 1 FAILED ");
}
#endif /* ENABLE_LCD_MSG_DISPLAY */
/* Second write in the memory followed by a read of the written data -------*/
/* Write on I2C EEPROM from sEE_WRITE_ADDRESS2 */
sEE_WriteBuffer(Tx2_Buffer, sEE_WRITE_ADDRESS2, BUFFER_SIZE2);
/* Wait for EEPROM standby state */
sEE_WaitEepromStandbyState();
/* Set the Number of data to be read */
NumDataRead = BUFFER_SIZE2;
/* Read from I2C EEPROM from sEE_READ_ADDRESS2 */
sEE_ReadBuffer(Rx2_Buffer, sEE_READ_ADDRESS2, (uint16_t *)(&NumDataRead));
/* Starting from this point, if the requested number of data is higher than 1,
then only the DMA is managing the data transfer. Meanwhile, CPU is free to
perform other tasks:
// Add your code here:
//...
//...
For simplicity reasons, this example is just waiting till the end of the
transfer. */
#ifdef ENABLE_LCD_MSG_DISPLAY
LCD_DisplayStringLine(LCD_LINE_5, " Transfer 2 Ongoing ");
#endif /* ENABLE_LCD_MSG_DISPLAY */
/* Wait till DMA transfer is compelete (Tranfer complete interrupt handler
resets the variable holding the number of data to be read) */
while (NumDataRead > 0)
{}
/* Check if the data written to the memory is read correctly */
TransferStatus2 = Buffercmp(Tx2_Buffer, Rx2_Buffer, BUFFER_SIZE2);
/* TransferStatus2 = PASSED, if the transmitted and received data
to/from the EEPROM are the same */
/* TransferStatus2 = FAILED, if the transmitted and received data
to/from the EEPROM are different */
#ifdef ENABLE_LCD_MSG_DISPLAY
if (TransferStatus2 == PASSED)
{
LCD_DisplayStringLine(LCD_LINE_5, " Transfer 2 PASSED ");
}
else
{
LCD_DisplayStringLine(LCD_LINE_5, " Transfer 2 FAILED ");
}
#endif /* ENABLE_LCD_MSG_DISPLAY */
/* Free all used resources */
sEE_DeInit();
while (1)
{
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
files (startup_stm32f40_41xxx.s/startup_stm32f427_437xx.s/startup_stm32f429_439xx.s)
before to branch to application main.
*/
/* SPI configuration */
SPI_Config();
/* SysTick configuration */
SysTickConfig();
/* LEDs configuration */
STM_EVAL_LEDInit(LED1);
STM_EVAL_LEDInit(LED2);
STM_EVAL_LEDInit(LED3);
STM_EVAL_LEDInit(LED4);
#ifdef SPI_MASTER
/* Master board configuration */
/* Initializes the SPI communication */
SPI_InitStructure.SPI_Mode = SPI_Mode_Master;
SPI_Init(SPIx, &SPI_InitStructure);
/* The Data transfer is performed in the SPI interrupt routine */
/* Configure the Tamper Button */
STM_EVAL_PBInit(BUTTON_TAMPER,BUTTON_MODE_GPIO);
/* Wait until Tamper Button is pressed */
while (STM_EVAL_PBGetState(BUTTON_TAMPER));
/* Enable the SPI peripheral */
SPI_Cmd(SPIx, ENABLE);
/* Initialize Buffer counters */
ubTxIndex = 0;
ubRxIndex = 0;
/* Enable the Rx buffer not empty interrupt */
SPI_I2S_ITConfig(SPIx, SPI_I2S_IT_RXNE, ENABLE);
/* Enable the Tx buffer empty interrupt */
SPI_I2S_ITConfig(SPIx, SPI_I2S_IT_TXE, ENABLE);
#endif /* SPI_MASTER */
#ifdef SPI_SLAVE
/* Slave board configuration */
/* Initializes the SPI communication */
SPI_InitStructure.SPI_Mode = SPI_Mode_Slave;
SPI_Init(SPIx, &SPI_InitStructure);
/* The Data transfer is performed in the SPI interrupt routine */
/* Initialize Buffer counters */
ubTxIndex = 0;
ubRxIndex = 0;
/* Enable the Rx buffer not empty interrupt */
SPI_I2S_ITConfig(SPIx, SPI_I2S_IT_RXNE, ENABLE);
/* Enable the Tx empty interrupt */
SPI_I2S_ITConfig(SPIx, SPI_I2S_IT_TXE, ENABLE);
/* Enable the SPI peripheral */
SPI_Cmd(SPIx, ENABLE);
#endif /* SPI_SLAVE */
/* Waiting the end of Data transfer */
while ((ubTxIndex < BUFFERSIZE) && (ubRxIndex < BUFFERSIZE))
{
}
/* Disable the Rx buffer not empty interrupt */
SPI_I2S_ITConfig(SPIx, SPI_I2S_IT_RXNE, DISABLE);
/* Disable the Tx empty interrupt */
SPI_I2S_ITConfig(SPIx, SPI_I2S_IT_TXE, DISABLE);
/* Disable the SPI peripheral */
SPI_Cmd(SPIx, DISABLE);
if (Buffercmp(aTxBuffer, aRxBuffer, BUFFERSIZE) != FAILED)
{
/* Turn ON LED1 and LED3 */
STM_EVAL_LEDOn(LED1);
STM_EVAL_LEDOn(LED3);
/* Turn OFF LED2 and LED4 */
STM_EVAL_LEDOff(LED2);
STM_EVAL_LEDOff(LED4);
}
else
{
/* Turn OFF LED1 and LED3 */
STM_EVAL_LEDOff(LED1);
STM_EVAL_LEDOff(LED3);
/* Turn ON LED2 and LED4 */
STM_EVAL_LEDOn(LED2);
STM_EVAL_LEDOn(LED4);
}
/* Infinite Loop */
while (1)
{
}
}
/**
* @brief Main program.
* @param None
* @retval None
*/
int main(void)
{
/* System Clocks Configuration */
RCC_Configuration();
/* FSMC for SRAM and SRAM pins configuration */
FSMC_SRAM_Init();
/* Write to FSMC -----------------------------------------------------------*/
/* DMA2 channel5 configuration */
DMA_DeInit(DMA2_Channel5);
DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)SRC_Const_Buffer;
DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)Bank1_SRAM3_ADDR;
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC;
DMA_InitStructure.DMA_BufferSize = 32;
DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Enable;
DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable;
DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Word;
DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_Word;
DMA_InitStructure.DMA_Mode = DMA_Mode_Normal;
DMA_InitStructure.DMA_Priority = DMA_Priority_High;
DMA_InitStructure.DMA_M2M = DMA_M2M_Enable;
DMA_Init(DMA2_Channel5, &DMA_InitStructure);
/* Enable DMA2 channel5 */
DMA_Cmd(DMA2_Channel5, ENABLE);
/* Check if DMA2 channel5 transfer is finished */
while(!DMA_GetFlagStatus(DMA2_FLAG_TC5));
/* Clear DMA2 channel5 transfer complete flag bit */
DMA_ClearFlag(DMA2_FLAG_TC5);
/* Read from FSMC ----------------------------------------------------------*/
/* Destination buffer initialization */
for(Idx=0; Idx<128; Idx++) DST_Buffer[Idx]=0;
/* DMA1 channel3 configuration */
DMA_DeInit(DMA1_Channel3);
DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)Bank1_SRAM3_ADDR;
DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)DST_Buffer;
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC;
DMA_InitStructure.DMA_BufferSize = 128;
DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Enable;
DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable;
DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte;
DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte;
DMA_InitStructure.DMA_Mode = DMA_Mode_Normal;
DMA_InitStructure.DMA_Priority = DMA_Priority_High;
DMA_InitStructure.DMA_M2M = DMA_M2M_Enable;
DMA_Init(DMA1_Channel3, &DMA_InitStructure);
/* Enable DMA1 channel3 */
DMA_Cmd(DMA1_Channel3, ENABLE);
/* Check if DMA1 channel3 transfer is finished */
while(!DMA_GetFlagStatus(DMA1_FLAG_TC3));
/* Clear DMA1 channel3 transfer complete flag bit */
DMA_ClearFlag(DMA1_FLAG_TC3);
/* Check if the transmitted and received data are equal */
TransferStatus = Buffercmp(SRC_Const_Buffer, (uint32_t*)DST_Buffer, BufferSize);
/* TransferStatus = PASSED, if the transmitted and received data
are the same */
/* TransferStatus = FAILED, if the transmitted and received data
are different */
while (1)
{
}
}
/**
* @brief SD Demo
* @param None
* @retval None
*/
void SD_demo (void)
{
uint8_t SD_state = MSD_OK;
__IO uint8_t prev_status = 0;
SD_SetHint();
SD_state = BSP_SD_Init();
/* Check if the SD card is plugged in the slot */
if(BSP_SD_IsDetected() == SD_PRESENT)
{
BSP_LCD_SetTextColor(LCD_COLOR_GREEN);
BSP_LCD_DisplayStringAt(20, BSP_LCD_GetYSize()-30, (uint8_t *)"SD Connected ", LEFT_MODE);
}
else
{
BSP_LCD_SetTextColor(LCD_COLOR_RED);
BSP_LCD_DisplayStringAt(20, BSP_LCD_GetYSize()-30, (uint8_t *)"SD Not Connected", LEFT_MODE);
}
BSP_LCD_SetTextColor(LCD_COLOR_BLACK);
if(SD_state != MSD_OK)
{
BSP_LCD_DisplayStringAt(20, 100, (uint8_t *)"SD INITIALIZATION : FAIL.", LEFT_MODE);
BSP_LCD_DisplayStringAt(20, 115, (uint8_t *)"SD Test Aborted.", LEFT_MODE);
}
else
{
BSP_LCD_DisplayStringAt(20, 100, (uint8_t *)"SD INITIALIZATION : OK.", LEFT_MODE);
BSP_SD_GetCardInfo(&CardInfo);
if(SD_state != MSD_OK)
{
BSP_LCD_DisplayStringAt(20, 115, (uint8_t *)"SD GET CARD INFO : FAIL.", LEFT_MODE);
BSP_LCD_DisplayStringAt(20, 130, (uint8_t *)"SD Test Aborted.", LEFT_MODE);
}
else
{
BSP_LCD_DisplayStringAt(20, 115, (uint8_t *)"SD GET CARD INFO : OK.", LEFT_MODE);
SD_state = BSP_SD_Erase(BLOCK_START_ADDR, (BLOCKSIZE * NUM_OF_BLOCKS));
/* Verify that SD card is ready to use after the Erase */
SD_state |= BSP_SD_GetStatus();
if(SD_state != MSD_OK)
{
BSP_LCD_DisplayStringAt(20, 130, (uint8_t *)"SD ERASE : FAILED.", LEFT_MODE);
BSP_LCD_DisplayStringAt(20, 145, (uint8_t *)"SD Test Aborted.", LEFT_MODE);
}
else
{
BSP_LCD_DisplayStringAt(20, 130, (uint8_t *)"SD ERASE : OK.", LEFT_MODE);
/* Fill the buffer to write */
Fill_Buffer(aTxBuffer, BUFFER_WORDS_SIZE, 0x22FF);
SD_state = BSP_SD_WriteBlocks((uint32_t *)aTxBuffer, BLOCK_START_ADDR, BLOCKSIZE, NUM_OF_BLOCKS);
if(SD_state != MSD_OK)
{
BSP_LCD_DisplayStringAt(20, 145, (uint8_t *)"SD WRITE : FAILED.", LEFT_MODE);
BSP_LCD_DisplayStringAt(20, 160, (uint8_t *)"SD Test Aborted.", LEFT_MODE);
}
else
{
BSP_LCD_DisplayStringAt(20, 145, (uint8_t *)"SD WRITE : OK.", LEFT_MODE);
SD_state = BSP_SD_ReadBlocks((uint32_t *)aRxBuffer, BLOCK_START_ADDR, BLOCKSIZE, NUM_OF_BLOCKS);
if(SD_state != MSD_OK)
{
BSP_LCD_DisplayStringAt(20, 160, (uint8_t *)"SD READ : FAILED.", LEFT_MODE);
BSP_LCD_DisplayStringAt(20, 175, (uint8_t *)"SD Test Aborted.", LEFT_MODE);
}
else
{
BSP_LCD_DisplayStringAt(20, 160, (uint8_t *)"SD READ : OK.", LEFT_MODE);
if(Buffercmp(aTxBuffer, aRxBuffer, BUFFER_WORDS_SIZE) > 0)
{
BSP_LCD_DisplayStringAt(20, 175, (uint8_t *)"SD COMPARE : FAILED.", LEFT_MODE);
BSP_LCD_DisplayStringAt(20, 190, (uint8_t *)"SD Test Aborted.", LEFT_MODE);
}
else
{
BSP_LCD_DisplayStringAt(20, 175, (uint8_t *)"SD TEST : OK.", LEFT_MODE);
}
}
}
}
}
}
while (1)
{
/* Check if the SD card is plugged in the slot */
if(BSP_SD_IsDetected() != SD_PRESENT)
{
if(prev_status == 0)
{
prev_status = 1;
BSP_LCD_SetTextColor(LCD_COLOR_RED);
BSP_LCD_DisplayStringAt(20, BSP_LCD_GetYSize()-30, (uint8_t *)"SD Not Connected", LEFT_MODE);
}
}
else if (prev_status == 1)
{
BSP_SD_Init();
BSP_LCD_SetTextColor(LCD_COLOR_GREEN);
BSP_LCD_DisplayStringAt(20, BSP_LCD_GetYSize()-30, (uint8_t *)"SD Connected ", LEFT_MODE);
prev_status = 0;
}
if(CheckForUserInput() > 0)
{
return;
}
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32f10x_xx.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32f10x.c file
*/
/* Initialize Leds mounted on STM3210X-EVAL board */
STM_EVAL_LEDInit(LED1);
STM_EVAL_LEDInit(LED2);
/* Initialize the SPI FLASH driver */
sFLASH_Init();
/* Get SPI Flash ID */
FlashID = sFLASH_ReadID();
/* Check the SPI Flash ID */
if (FlashID == sFLASH_ID)
{
/* OK: Turn on LD1 */
STM_EVAL_LEDOn(LED1);
/* Perform a write in the Flash followed by a read of the written data */
/* Erase SPI FLASH Sector to write on */
sFLASH_EraseSector(FLASH_SectorToErase);
/* Write Tx_Buffer data to SPI FLASH memory */
sFLASH_WriteBuffer(Tx_Buffer, FLASH_WriteAddress, BufferSize);
/* Read data from SPI FLASH memory */
sFLASH_ReadBuffer(Rx_Buffer, FLASH_ReadAddress, BufferSize);
/* Check the correctness of written dada */
TransferStatus1 = Buffercmp(Tx_Buffer, Rx_Buffer, BufferSize);
/* TransferStatus1 = PASSED, if the transmitted and received data by SPI1
are the same */
/* TransferStatus1 = FAILED, if the transmitted and received data by SPI1
are different */
/* Perform an erase in the Flash followed by a read of the written data */
/* Erase SPI FLASH Sector to write on */
sFLASH_EraseSector(FLASH_SectorToErase);
/* Read data from SPI FLASH memory */
sFLASH_ReadBuffer(Rx_Buffer, FLASH_ReadAddress, BufferSize);
/* Check the correctness of erasing operation dada */
for (Index = 0; Index < BufferSize; Index++)
{
if (Rx_Buffer[Index] != 0xFF)
{
TransferStatus2 = FAILED;
}
}
/* TransferStatus2 = PASSED, if the specified sector part is erased */
/* TransferStatus2 = FAILED, if the specified sector part is not well erased */
}
else
{
/* Error: Turn on LD2 */
STM_EVAL_LEDOn(LED2);
}
while (1)
{}
}
/**
* @brief Main program.
* @param None
* @retval None
*/
int main(void)
{
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32f0xx.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32f0xx.c file
*/
/* SPI configuration ------------------------------------------------------*/
SPI_Config();
/* SysTick configuration ---------------------------------------------------*/
SysTickConfig();
/* Initialize LEDs mounted on STM320518-EVAL board */
STM_EVAL_LEDInit(LED1);
STM_EVAL_LEDInit(LED2);
STM_EVAL_LEDInit(LED3);
STM_EVAL_LEDInit(LED4);
/* Master board configuration ------------------------------------------------*/
#ifdef SPI_MASTER
/* Initialize push-buttons mounted on STM320518-EVAL board */
STM_EVAL_PBInit(BUTTON_RIGHT, BUTTON_MODE_GPIO);
STM_EVAL_PBInit(BUTTON_LEFT, BUTTON_MODE_GPIO);
STM_EVAL_PBInit(BUTTON_UP, BUTTON_MODE_GPIO);
STM_EVAL_PBInit(BUTTON_DOWN, BUTTON_MODE_GPIO);
STM_EVAL_PBInit(BUTTON_SEL, BUTTON_MODE_GPIO);
/* Initializes the SPI communication */
SPI_InitStructure.SPI_Mode = SPI_Mode_Master;
SPI_Init(SPIx, &SPI_InitStructure);
/* Initialize the FIFO threshold */
SPI_RxFIFOThresholdConfig(SPIx, SPI_RxFIFOThreshold_QF);
/* TIM configuration ------------------------------------------------------*/
TIM_Config();
/* Enable the SPI peripheral */
SPI_Cmd(SPIx, ENABLE);
/* Enable NSS output for master mode */
SPI_SSOutputCmd(SPIx, ENABLE);
/* TIM Capture Compare DMA Request enable */
TIM_DMACmd(TIMx, TIMx_DMA_CHANNEL, ENABLE);
while (1)
{
/* DMA channel Rx of SPI Configuration */
DMA_InitStructure.DMA_BufferSize = (uint16_t)1;
DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)SPIx_DR_ADDRESS;
DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t) &CommandReceived;
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC;
DMA_InitStructure.DMA_Priority = DMA_Priority_High;
DMA_Init(SPIx_RX_DMA_CHANNEL, &DMA_InitStructure);
/* DMA TIM trigger channel Configuration */
DMA_InitStructure.DMA_BufferSize = (uint16_t)1;
DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)SPIx_DR_ADDRESS;
DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t) &CommandTransmitted;
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralDST;
DMA_InitStructure.DMA_Priority = DMA_Priority_Low;
DMA_Init(TIMx_CHANNEL_DMA_CHANNEL, &DMA_InitStructure);
/* Enable the SPI Rx DMA request */
SPI_I2S_DMACmd(SPIx, SPI_I2S_DMAReq_Rx, ENABLE);
CommandTransmitted = 0x00;
CommandReceived = 0x00;
/* Clear the RxBuffer */
Fill_Buffer(RxBuffer, TXBUFFERSIZE);
PressedButton = Read_Joystick();
while (PressedButton == JOY_NONE)
{
PressedButton = Read_Joystick();
}
switch (PressedButton)
{
/* JOY_RIGHT button pressed */
case JOY_RIGHT:
CommandTransmitted = CMD_RIGHT;
NumberOfByte = CMD_RIGHT_SIZE;
break;
/* JOY_LEFT button pressed */
case JOY_LEFT:
CommandTransmitted = CMD_LEFT;
NumberOfByte = CMD_LEFT_SIZE;
break;
/* JOY_UP button pressed */
case JOY_UP:
CommandTransmitted = CMD_UP;
NumberOfByte = CMD_UP_SIZE;
break;
/* JOY_DOWN button pressed */
case JOY_DOWN:
CommandTransmitted = CMD_DOWN;
NumberOfByte = CMD_DOWN_SIZE;
break;
/* JOY_SEL button pressed */
case JOY_SEL:
CommandTransmitted = CMD_SEL;
NumberOfByte = CMD_SEL_SIZE;
break;
default:
break;
}
/* Enable the DMA channel */
DMA_Cmd(SPIx_RX_DMA_CHANNEL, ENABLE);
/* Enable DMA1 TIM Trigger Channel */
DMA_Cmd(TIMx_CHANNEL_DMA_CHANNEL, ENABLE);
/* TIM enable counter */
TIM_Cmd(TIMx, ENABLE);
/* Wait the SPI DMA Rx transfer complete or time out*/
TimeOut = USER_TIMEOUT;
while ((DMA_GetFlagStatus(SPIx_RX_DMA_FLAG_TC) == RESET)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* The BSY flag can be monitored to ensure that the SPI communication is complete.
This is required to avoid corrupting the last transmission before disabling
the SPI or entering the Stop mode. The software must first wait until TXE=1
and then until BSY=0.*/
TimeOut = USER_TIMEOUT;
while ((SPI_I2S_GetFlagStatus(SPIx, SPI_I2S_FLAG_TXE) == RESET)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
TimeOut = USER_TIMEOUT;
while ((SPI_I2S_GetFlagStatus(SPIx, SPI_I2S_FLAG_BSY) == SET)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Clear DMA1 global flags*/
DMA_ClearFlag(TIMx_CHANNEL_DMA_FLAG_GL);
DMA_ClearFlag(SPIx_RX_DMA_FLAG_GL);
/* disable the DMA channels */
DMA_Cmd(SPIx_RX_DMA_CHANNEL, DISABLE);
DMA_Cmd(TIMx_CHANNEL_DMA_CHANNEL, DISABLE);
/* disable the SPI Rx DMA request */
SPI_I2S_DMACmd(SPIx, SPI_I2S_DMAReq_Rx, DISABLE);
/* TIM disable counter */
TIM_Cmd(TIMx, DISABLE);
if (CommandReceived == CMD_ACK)
{
/* DMA channel Rx of SPI Configuration */
DMA_InitStructure.DMA_BufferSize = (uint16_t)NumberOfByte;
DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)SPIx_DR_ADDRESS;
DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)RxBuffer;
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC;
DMA_InitStructure.DMA_Priority = DMA_Priority_High;
DMA_Init(SPIx_RX_DMA_CHANNEL, &DMA_InitStructure);
/* DMA channel Tx of SPI Configuration */
DMA_InitStructure.DMA_BufferSize = (uint16_t)NumberOfByte;
DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)SPIx_DR_ADDRESS;
DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)TxBuffer;
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralDST;
DMA_InitStructure.DMA_Priority = DMA_Priority_Low;
DMA_Init(TIMx_CHANNEL_DMA_CHANNEL, &DMA_InitStructure);
/* Enable the SPI Rx DMA request */
SPI_I2S_DMACmd(SPIx, SPI_I2S_DMAReq_Rx, ENABLE);
/* Enable the DMA channel */
DMA_Cmd(SPIx_RX_DMA_CHANNEL, ENABLE);
/* Enable DMA1 TIM Trigger Channel */
DMA_Cmd(TIMx_CHANNEL_DMA_CHANNEL, ENABLE);
/* TIM enable counter */
TIM_Cmd(TIMx, ENABLE);
/* Wait the SPI Rx DMA transfer complete or time out */
TimeOut = USER_TIMEOUT;
while ((DMA_GetFlagStatus(SPIx_RX_DMA_FLAG_TC) == RESET)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* The BSY flag can be monitored to ensure that the SPI communication is complete.
This is required to avoid corrupting the last transmission before disabling
the SPI or entering the Stop mode. The software must first wait until TXE=1
and then until BSY=0.*/
TimeOut = USER_TIMEOUT;
while ((SPI_I2S_GetFlagStatus(SPIx, SPI_I2S_FLAG_TXE) == RESET)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
TimeOut = USER_TIMEOUT;
while ((SPI_I2S_GetFlagStatus(SPIx, SPI_I2S_FLAG_BSY) == SET)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Clear DMA1 global flags */
DMA_ClearFlag(TIMx_CHANNEL_DMA_FLAG_GL);
DMA_ClearFlag(SPIx_RX_DMA_FLAG_GL);
/* Disable the DMA channels */
DMA_Cmd(SPIx_RX_DMA_CHANNEL, DISABLE);
DMA_Cmd(TIMx_CHANNEL_DMA_CHANNEL, DISABLE);
/* Disable the SPI Rx and Tx DMA requests */
SPI_I2S_DMACmd(SPIx, SPI_I2S_DMAReq_Rx, DISABLE);
/* TIM disable counter */
TIM_Cmd(TIMx, DISABLE);
switch (NumberOfByte)
{
/* CMD_RIGHT command received */
case CMD_RIGHT_SIZE:
if ((Buffercmp(TxBuffer, RxBuffer, CMD_RIGHT_SIZE, SPI_DATAMASK) != FAILED) && (CommandReceived == CMD_ACK))
{
/* Turn ON LED2 and LED3 */
STM_EVAL_LEDOn(LED2);
STM_EVAL_LEDOn(LED3);
/* Turn OFF LED4 */
STM_EVAL_LEDOff(LED4);
}
break;
/* CMD_LEFT command received */
case CMD_LEFT_SIZE:
if ((Buffercmp(TxBuffer, RxBuffer, CMD_LEFT_SIZE, SPI_DATAMASK) != FAILED) && (CommandReceived == CMD_ACK))
{
/* Turn ON LED4 */
STM_EVAL_LEDOn(LED4);
/* Turn OFF LED2 and LED3 */
STM_EVAL_LEDOff(LED2);
STM_EVAL_LEDOff(LED3);
}
break;
/* CMD_UP command received */
case CMD_UP_SIZE:
if ((Buffercmp(TxBuffer, RxBuffer, CMD_UP_SIZE, SPI_DATAMASK) != FAILED) && (CommandReceived == CMD_ACK))
{
/* Turn ON LED2 */
STM_EVAL_LEDOn(LED2);
/* Turn OFF LED3 and LED4 */
STM_EVAL_LEDOff(LED3);
STM_EVAL_LEDOff(LED4);
}
break;
/* CMD_DOWN command received */
case CMD_DOWN_SIZE:
if ((Buffercmp(TxBuffer, RxBuffer, CMD_DOWN_SIZE, SPI_DATAMASK) != FAILED) && (CommandReceived == CMD_ACK))
{
/* Turn ON LED3 */
STM_EVAL_LEDOn(LED3);
/* Turn OFF LED2 and LED4 */
STM_EVAL_LEDOff(LED2);
STM_EVAL_LEDOff(LED4);
}
break;
/* CMD_SEL command received */
case CMD_SEL_SIZE:
if ((Buffercmp(TxBuffer, RxBuffer, CMD_SEL_SIZE, SPI_DATAMASK) != FAILED) && (CommandReceived == CMD_ACK))
{
/* Turn ON LED2, LED3 and LED4 */
STM_EVAL_LEDOn(LED2);
STM_EVAL_LEDOn(LED3);
STM_EVAL_LEDOn(LED4);
}
break;
default:
break;
}
}
}
#endif /* SPI_MASTER */
/* Slave board configuration -----------------------------------------------*/
#ifdef SPI_SLAVE
/* Initializes the SPI communication */
SPI_I2S_DeInit(SPIx);
SPI_InitStructure.SPI_Mode = SPI_Mode_Slave;
SPI_Init(SPIx, &SPI_InitStructure);
/* Initialize the FIFO threshold */
SPI_RxFIFOThresholdConfig(SPIx, SPI_RxFIFOThreshold_QF);
CommandTransmitted = CMD_ACK;
/* Infinite Loop */
while (1)
{
/* DMA channel Rx of SPI Configuration */
DMA_InitStructure.DMA_BufferSize = 1;
DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)SPIx_DR_ADDRESS;
DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t) &CommandReceived;
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC;
DMA_InitStructure.DMA_Priority = DMA_Priority_High;
DMA_Init(SPIx_RX_DMA_CHANNEL, &DMA_InitStructure);
/* DMA channel Tx of SPI Configuration */
DMA_InitStructure.DMA_BufferSize = 1;
DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)SPIx_DR_ADDRESS;
DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t) &CommandTransmitted;
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralDST;
DMA_InitStructure.DMA_Priority = DMA_Priority_Low;
DMA_Init(SPIx_TX_DMA_CHANNEL, &DMA_InitStructure);
/* Enable the SPI Rx and Tx DMA requests */
SPI_I2S_DMACmd(SPIx, SPI_I2S_DMAReq_Rx, ENABLE);
SPI_I2S_DMACmd(SPIx, SPI_I2S_DMAReq_Tx, ENABLE);
/* Enable the SPI peripheral */
SPI_Cmd(SPIx, ENABLE);
CommandReceived = 0x00;
/* Enable the DMA channels */
DMA_Cmd(SPIx_RX_DMA_CHANNEL, ENABLE);
DMA_Cmd(SPIx_TX_DMA_CHANNEL, ENABLE);
/* Wait the SPI DMA transfers complete or time out */
while (DMA_GetFlagStatus(SPIx_RX_DMA_FLAG_TC) == RESET)
{}
TimeOut = USER_TIMEOUT;
while ((DMA_GetFlagStatus(SPIx_TX_DMA_FLAG_TC) == RESET)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* The BSY flag can be monitored to ensure that the SPI communication is complete.
This is required to avoid corrupting the last transmission before disabling
the SPI or entering the Stop mode. The software must first wait until TXE=1
and then until BSY=0.*/
TimeOut = USER_TIMEOUT;
while ((SPI_I2S_GetFlagStatus(SPIx, SPI_I2S_FLAG_TXE) == RESET)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
TimeOut = USER_TIMEOUT;
while ((SPI_I2S_GetFlagStatus(SPIx, SPI_I2S_FLAG_BSY) == SET)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Clear DMA1 global flags */
DMA_ClearFlag(SPIx_TX_DMA_FLAG_GL);
DMA_ClearFlag(SPIx_RX_DMA_FLAG_GL);
/* Disable the DMA channels */
DMA_Cmd(SPIx_RX_DMA_CHANNEL, DISABLE);
DMA_Cmd(SPIx_TX_DMA_CHANNEL, DISABLE);
/* Disable the SPI peripheral */
SPI_Cmd(SPIx, DISABLE);
/* Disable the SPI Rx and Tx DMA requests */
SPI_I2S_DMACmd(SPIx, SPI_I2S_DMAReq_Rx, DISABLE);
SPI_I2S_DMACmd(SPIx, SPI_I2S_DMAReq_Tx, DISABLE);
switch (CommandReceived)
{
/* CMD_RIGHT command received */
case CMD_RIGHT:
NumberOfByte = CMD_RIGHT_SIZE;
break;
/* CMD_LEFT command received */
case CMD_LEFT:
NumberOfByte = CMD_LEFT_SIZE;
break;
/* CMD_UP command received */
case CMD_UP:
NumberOfByte = CMD_UP_SIZE;
break;
/* CMD_DOWN command received */
case CMD_DOWN:
NumberOfByte = CMD_DOWN_SIZE;
break;
/* CMD_SEL command received */
case CMD_SEL:
NumberOfByte = CMD_SEL_SIZE;
break;
default:
break;
}
/* DMA channel Rx of SPI Configuration */
DMA_InitStructure.DMA_BufferSize = NumberOfByte;
DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)SPIx_DR_ADDRESS;
DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)RxBuffer;
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC;
DMA_InitStructure.DMA_Priority = DMA_Priority_High;
DMA_Init(SPIx_RX_DMA_CHANNEL, &DMA_InitStructure);
/* DMA channel Tx of SPI Configuration */
DMA_InitStructure.DMA_BufferSize = NumberOfByte;
DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)SPIx_DR_ADDRESS;
DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)TxBuffer;
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralDST;
DMA_InitStructure.DMA_Priority = DMA_Priority_Low;
DMA_Init(SPIx_TX_DMA_CHANNEL, &DMA_InitStructure);
/* Enable the SPI Rx and Tx DMA requests */
SPI_I2S_DMACmd(SPIx, SPI_I2S_DMAReq_Rx, ENABLE);
SPI_I2S_DMACmd(SPIx, SPI_I2S_DMAReq_Tx, ENABLE);
/* Enable the SPI peripheral */
SPI_Cmd(SPIx, ENABLE);
/* Enable the DMA channels */
DMA_Cmd(SPIx_RX_DMA_CHANNEL, ENABLE);
DMA_Cmd(SPIx_TX_DMA_CHANNEL, ENABLE);
/* Wait the SPI DMA transfers complete or time out */
while (DMA_GetFlagStatus(SPIx_RX_DMA_FLAG_TC) == RESET)
{}
TimeOut = USER_TIMEOUT;
while ((DMA_GetFlagStatus(SPIx_TX_DMA_FLAG_TC) == RESET)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* The BSY flag can be monitored to ensure that the SPI communication is complete.
This is required to avoid corrupting the last transmission before disabling
the SPI or entering the Stop mode. The software must first wait until TXE=1
and then until BSY=0.*/
TimeOut = USER_TIMEOUT;
while ((SPI_I2S_GetFlagStatus(SPIx, SPI_I2S_FLAG_TXE) == RESET)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
TimeOut = USER_TIMEOUT;
while ((SPI_I2S_GetFlagStatus(SPIx, SPI_I2S_FLAG_BSY) == SET)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
switch (NumberOfByte)
{
/* CMD_RIGHT command received */
case CMD_RIGHT_SIZE:
if (Buffercmp(TxBuffer, RxBuffer, CMD_RIGHT_SIZE, SPI_DATAMASK) != FAILED)
{
/* Turn ON LED2 and LED3 */
STM_EVAL_LEDOn(LED2);
STM_EVAL_LEDOn(LED3);
/* Turn OFF LED4 */
STM_EVAL_LEDOff(LED4);
}
break;
/* CMD_LEFT command received */
case CMD_LEFT_SIZE:
if (Buffercmp(TxBuffer, RxBuffer, CMD_LEFT_SIZE, SPI_DATAMASK) != FAILED)
{
/* Turn ON LED4 */
STM_EVAL_LEDOn(LED4);
/* Turn OFF LED2 and LED3 */
STM_EVAL_LEDOff(LED2);
STM_EVAL_LEDOff(LED3);
}
break;
/* CMD_UP command received */
case CMD_UP_SIZE:
if (Buffercmp(TxBuffer, RxBuffer, CMD_UP_SIZE, SPI_DATAMASK) != FAILED)
{
/* Turn ON LED2 */
STM_EVAL_LEDOn(LED2);
/* Turn OFF LED3 and LED4 */
STM_EVAL_LEDOff(LED3);
STM_EVAL_LEDOff(LED4);
}
break;
/* CMD_DOWN command received */
case CMD_DOWN_SIZE:
if (Buffercmp(TxBuffer, RxBuffer, CMD_DOWN_SIZE, SPI_DATAMASK) != FAILED)
{
/* Turn ON LED3 */
STM_EVAL_LEDOn(LED3);
/* Turn OFF LED2 and LED4 */
STM_EVAL_LEDOff(LED2);
STM_EVAL_LEDOff(LED4);
}
break;
/* CMD_SEL command received */
case CMD_SEL_SIZE:
if (Buffercmp(TxBuffer, RxBuffer, CMD_SEL_SIZE, SPI_DATAMASK) != FAILED)
{
/* Turn ON LED2, LED3 and LED4 */
STM_EVAL_LEDOn(LED2);
STM_EVAL_LEDOn(LED3);
STM_EVAL_LEDOn(LED4);
}
break;
default:
break;
}
/* Clear DMA1 global flags */
DMA_ClearFlag(SPIx_TX_DMA_FLAG_GL);
DMA_ClearFlag(SPIx_RX_DMA_FLAG_GL);
/* Disable the DMA channels */
DMA_Cmd(SPIx_RX_DMA_CHANNEL, DISABLE);
DMA_Cmd(SPIx_TX_DMA_CHANNEL, DISABLE);
/* Disable the SPI peripheral */
SPI_Cmd(SPIx, DISABLE);
/* Disable the SPI Rx and Tx DMA requests */
SPI_I2S_DMACmd(SPIx, SPI_I2S_DMAReq_Rx, DISABLE);
SPI_I2S_DMACmd(SPIx, SPI_I2S_DMAReq_Tx, DISABLE);
}
#endif /* SPI_SLAVE */
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32f10x_xx.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32f10x.c file
*/
/* System Clocks Configuration */
RCC_Configuration();
/* Configure the GPIO ports */
GPIO_Configuration();
/* USARTy and USARTz configuration -------------------------------------------*/
/* USARTy and USARTz configured as follow:
- BaudRate = 230400 baud
- Word Length = 8 Bits
- One Stop Bit
- No parity
- Hardware flow control disabled (RTS and CTS signals)
- Receive and transmit enabled
*/
USART_InitStructure.USART_BaudRate = 230400;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
/* Configure USARTy */
USART_Init(USARTy, &USART_InitStructure);
/* Configure USARTz */
USART_Init(USARTz, &USART_InitStructure);
/* Enable the USARTy */
USART_Cmd(USARTy, ENABLE);
/* Enable the USARTz */
USART_Cmd(USARTz, ENABLE);
/* Enable USARTy Half Duplex Mode*/
USART_HalfDuplexCmd(USARTy, ENABLE);
/* Enable USARTz Half Duplex Mode*/
USART_HalfDuplexCmd(USARTz, ENABLE);
while(NbrOfDataToRead2--)
{
/* Wait until end of transmit */
while(USART_GetFlagStatus(USARTy, USART_FLAG_TXE) == RESET)
{
}
/* Write one byte in the USARTy Transmit Data Register */
USART_SendData(USARTy, TxBuffer1[TxCounter1++]);
/* Wait the byte is entirtly received by USARTz */
while(USART_GetFlagStatus(USARTz, USART_FLAG_RXNE) == RESET)
{
}
/* Store the received byte in the RxBuffer2 */
RxBuffer2[RxCounter2++] = USART_ReceiveData(USARTz);
}
/* Clear the USARTy Data Register */
USART_ReceiveData(USARTy);
while(NbrOfDataToRead1--)
{
/* Wait until end of transmit */
while(USART_GetFlagStatus(USARTz, USART_FLAG_TXE)== RESET)
{
}
/* Write one byte in the USARTz Transmit Data Register */
USART_SendData(USARTz, TxBuffer2[TxCounter2++]);
/* Wait the byte is entirtly received by USARTy */
while(USART_GetFlagStatus(USARTy,USART_FLAG_RXNE) == RESET)
{
}
/* Store the received byte in the RxBuffer1 */
RxBuffer1[RxCounter1++] = USART_ReceiveData(USARTy);
}
/* Check the received data with the send ones */
TransferStatus1 = Buffercmp(TxBuffer1, RxBuffer2, TxBufferSize1);
/* TransferStatus = PASSED, if the data transmitted from USARTy and
received by USARTz are the same */
/* TransferStatus = FAILED, if the data transmitted from USARTy and
received by USARTz are different */
TransferStatus2 = Buffercmp(TxBuffer2, RxBuffer1, TxBufferSize2);
/* TransferStatus = PASSED, if the data transmitted from USARTz and
received by USARTy are the same */
/* TransferStatus = FAILED, if the data transmitted from USARTz and
received by USARTy are different */
while (1)
{
}
}
/**
* @brief Main program.
* @param None
* @retval None
*/
int main(void)
{
/* STM32L0xx HAL library initialization:
- Configure the Flash prefetch, Flash preread and Buffer caches
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Low Level Initialization
*/
HAL_Init();
/* Configure LED2 */
BSP_LED_Init(LED2);
/* Configure the system clock to 32 Mhz */
SystemClock_Config();
/*##-1- Configure the UART peripheral ######################################*/
/* Put the USART peripheral in the Asynchronous mode (UART Mode) */
/* UART1 configured as follow:
- Word Length = 8 Bits
- Stop Bit = One Stop bit
- Parity = None
- BaudRate = 9600 baud
- Hardware flow control disabled (RTS and CTS signals) */
UartHandle.Instance = USARTx;
UartHandle.Init.BaudRate = 9600;
UartHandle.Init.WordLength = UART_WORDLENGTH_8B;
UartHandle.Init.StopBits = UART_STOPBITS_1;
UartHandle.Init.Parity = UART_PARITY_NONE;
UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE;
UartHandle.Init.Mode = UART_MODE_TX_RX;
if(HAL_UART_Init(&UartHandle) != HAL_OK)
{
Error_Handler();
}
#ifdef TRANSMITTER_BOARD
/* Configure Button Key */
BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_GPIO);
/* Toggle led2 waiting for user to press button */
BSP_LED_On(LED2);
/* Wait for Button Key press before starting the Communication */
while (BSP_PB_GetState(BUTTON_KEY) == RESET)
{
}
/* Wait for Button Key to be release before starting the Communication */
while (BSP_PB_GetState(BUTTON_KEY) == SET)
{
}
/* Turn led2 off */
BSP_LED_Off(LED2);
/* The board sends the message and expects to receive it back */
/*##-2- Start the transmission process #####################################*/
/* While the UART in reception process, user can transmit data through
"aTxBuffer" buffer */
if(HAL_UART_Transmit_IT(&UartHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
{
Error_Handler();
}
/*##-3- Wait for the end of the transfer ###################################*/
while (UartReady != SET)
{
}
/* Reset transmission flag */
UartReady = RESET;
/*##-4- Put UART peripheral in reception process ###########################*/
if(HAL_UART_Receive_IT(&UartHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
{
Error_Handler();
}
#else
/* The board receives the message and sends it back */
/*##-2- Put UART peripheral in reception process ###########################*/
if(HAL_UART_Receive_IT(&UartHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
{
Error_Handler();
}
/*##-3- Wait for the end of the transfer ###################################*/
while (UartReady != SET)
{
}
/* Reset transmission flag */
UartReady = RESET;
/*##-4- Start the transmission process #####################################*/
/* While the UART in reception process, user can transmit data through
"aTxBuffer" buffer */
if(HAL_UART_Transmit_IT(&UartHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
{
Error_Handler();
}
#endif /* TRANSMITTER_BOARD */
/*##-5- Wait for the end of the transfer ###################################*/
while (UartReady != SET)
{
}
/* Reset transmission flag */
UartReady = RESET;
/*##-6- Compare the sent and received buffers ##############################*/
if(Buffercmp((uint8_t*)aTxBuffer,(uint8_t*)aRxBuffer,RXBUFFERSIZE))
{
Error_Handler();
}
/* Turn LED2 on: Transfer process is correct */
BSP_LED_On(LED2);
/* Infinite loop */
while (1)
{
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32F0xx HAL library initialization:
- Configure the Flash prefetch
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Low Level Initialization
*/
HAL_Init();
/* Configure LED3 */
BSP_LED_Init(LED3);
/* Configure the system clock to 48 MHz */
SystemClock_Config();
#ifdef BOARD_IN_STOP_MODE
/* HSI must be UART clock source to be able to wake up the MCU */
USARTx_RCC_CONFIG(RCC_USARTxCLKSOURCE_HSI);
#endif
/*##-1- Configure the UART peripheral ######################################*/
/* Put the USART peripheral in the Asynchronous mode (UART Mode) */
/* UART configured as follows:
- Word Length = 8 Bits
- Stop Bit = One Stop bit
- Parity = None
- BaudRate = 9600 baud
- Hardware flow control disabled (RTS and CTS signals) */
UartHandle.Instance = USARTx;
HAL_UART_DeInit(&UartHandle);
UartHandle.Init.BaudRate = 9600;
UartHandle.Init.WordLength = UART_WORDLENGTH_8B;
UartHandle.Init.StopBits = UART_STOPBITS_1;
UartHandle.Init.Parity = UART_PARITY_NONE;
UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE;
UartHandle.Init.Mode = UART_MODE_TX_RX;
UartHandle.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;
if(HAL_UART_Init(&UartHandle) != HAL_OK)
{
Error_Handler();
}
#ifdef BOARD_IN_STOP_MODE
BSP_LED_On(LED3);
/* wait for two seconds before test start */
HAL_Delay(2000);
/* make sure that no UART transfer is on-going */
while(__HAL_UART_GET_FLAG(&UartHandle, USART_ISR_BUSY) == SET);
/* make sure that UART is ready to receive
* (test carried out again later in HAL_UARTEx_StopModeWakeUpSourceConfig) */
while(__HAL_UART_GET_FLAG(&UartHandle, USART_ISR_REACK) == RESET);
/* set the wake-up event:
* specify wake-up on RXNE flag */
WakeUpSelection.WakeUpEvent = UART_WAKEUP_ON_READDATA_NONEMPTY;
if (HAL_UARTEx_StopModeWakeUpSourceConfig(&UartHandle, WakeUpSelection)!= HAL_OK)
{
Error_Handler();
}
/* Enable the UART Wake UP from stop mode Interrupt */
__HAL_UART_ENABLE_IT(&UartHandle, UART_IT_WUF);
/* about to enter stop mode: switch off LED */
BSP_LED_Off(LED3);
/* enable MCU wake-up by UART */
HAL_UARTEx_EnableStopMode(&UartHandle);
/* enter stop mode */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* ... STOP mode ... */
SystemClock_Config_fromSTOP();
/* at that point, MCU has been awoken: the LED has been turned back on */
/* Wake Up based on RXNE flag successful */
HAL_UARTEx_DisableStopMode(&UartHandle);
/* wait for some delay */
HAL_Delay(100);
/* Inform other board that wake up is successful */
if (HAL_UART_Transmit(&UartHandle, (uint8_t*)aTxBuffer1, COUNTOF(aTxBuffer1)-1, 5000)!= HAL_OK)
{
Error_Handler();
}
/*##-2- Wake Up second step ###############################################*/
/* make sure that no UART transfer is on-going */
while(__HAL_UART_GET_FLAG(&UartHandle, USART_ISR_BUSY) == SET);
/* make sure that UART is ready to receive
* (test carried out again later in HAL_UARTEx_StopModeWakeUpSourceConfig) */
while(__HAL_UART_GET_FLAG(&UartHandle, USART_ISR_REACK) == RESET);
/* set the wake-up event:
* specify wake-up on start-bit detection */
WakeUpSelection.WakeUpEvent = UART_WAKEUP_ON_STARTBIT;
if (HAL_UARTEx_StopModeWakeUpSourceConfig(&UartHandle, WakeUpSelection)!= HAL_OK)
{
Error_Handler();
}
/* Enable the UART Wake UP from stop mode Interrupt */
__HAL_UART_ENABLE_IT(&UartHandle, UART_IT_WUF);
/* about to enter stop mode: switch off LED */
BSP_LED_Off(LED3);
/* enable MCU wake-up by UART */
HAL_UARTEx_EnableStopMode(&UartHandle);
/* enter stop mode */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* ... STOP mode ... */
SystemClock_Config_fromSTOP();
/* at that point, MCU has been awoken: the LED has been turned back on */
/* Wake Up on start bit detection successful */
HAL_UARTEx_DisableStopMode(&UartHandle);
/* wait for some delay */
HAL_Delay(100);
/* Inform other board that wake up is successful */
if (HAL_UART_Transmit(&UartHandle, (uint8_t*)aTxBuffer2, COUNTOF(aTxBuffer2)-1, 5000)!= HAL_OK)
{
Error_Handler();
}
/*##-3- Wake Up third step ################################################*/
/* make sure that no UART transfer is on-going */
while(__HAL_UART_GET_FLAG(&UartHandle, USART_ISR_BUSY) == SET);
/* make sure that UART is ready to receive
* (test carried out again later in HAL_UARTEx_StopModeWakeUpSourceConfig) */
while(__HAL_UART_GET_FLAG(&UartHandle, USART_ISR_REACK) == RESET);
/* set the wake-up event:
* specify address-to-match type.
* The address is 0x29, meaning the character triggering the
* address match is 0xA9 */
WakeUpSelection.WakeUpEvent = UART_WAKEUP_ON_ADDRESS;
WakeUpSelection.AddressLength = UART_ADDRESS_DETECT_7B;
WakeUpSelection.Address = 0x29;
if (HAL_UARTEx_StopModeWakeUpSourceConfig(&UartHandle, WakeUpSelection)!= HAL_OK)
{
Error_Handler();
}
/* Enable the UART Wake UP from stop mode Interrupt */
__HAL_UART_ENABLE_IT(&UartHandle, UART_IT_WUF);
/* about to enter stop mode: switch off LED */
BSP_LED_Off(LED3);
/* enable MCU wake-up by UART */
HAL_UARTEx_EnableStopMode(&UartHandle);
/* enter stop mode */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* ... STOP mode ... */
SystemClock_Config_fromSTOP();
/* at that point, MCU has been awoken: the LED has been turned back on */
/* Wake Up on 7-bit address detection successful */
HAL_UARTEx_DisableStopMode(&UartHandle);
/* wait for some delay */
HAL_Delay(100);
/* Inform other board that wake up is successful */
if (HAL_UART_Transmit(&UartHandle, (uint8_t*)aTxBuffer3, COUNTOF(aTxBuffer3)-1, 5000)!= HAL_OK)
{
Error_Handler();
}
/*##-4- Wake Up fourth step ###############################################*/
/* make sure that no UART transfer is on-going */
while(__HAL_UART_GET_FLAG(&UartHandle, USART_ISR_BUSY) == SET);
/* make sure that UART is ready to receive
* (test carried out again later in HAL_UARTEx_StopModeWakeUpSourceConfig) */
while(__HAL_UART_GET_FLAG(&UartHandle, USART_ISR_REACK) == RESET);
/* set the wake-up event:
* specify address-to-match type.
* The address is 0x2, meaning the character triggering the
* address match is 0x82 */
WakeUpSelection.WakeUpEvent = UART_WAKEUP_ON_ADDRESS;
WakeUpSelection.AddressLength = UART_ADDRESS_DETECT_4B;
WakeUpSelection.Address = 0x2;
if (HAL_UARTEx_StopModeWakeUpSourceConfig(&UartHandle, WakeUpSelection)!= HAL_OK)
{
Error_Handler();
}
/* Enable the UART Wake UP from stop mode Interrupt */
__HAL_UART_ENABLE_IT(&UartHandle, UART_IT_WUF);
/* about to enter stop mode: switch off LED */
BSP_LED_Off(LED3);
/* enable MCU wake-up by UART */
HAL_UARTEx_EnableStopMode(&UartHandle);
/* enter stop mode */
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
/* ... STOP mode ... */
SystemClock_Config_fromSTOP();
/* at that point, MCU has been awoken: the LED has been turned back on */
/* Wake Up on 4-bit address detection successful */
/* wait for some delay */
HAL_Delay(100);
/* Inform other board that wake up is successful */
if (HAL_UART_Transmit(&UartHandle, (uint8_t*)aTxBuffer4, COUNTOF(aTxBuffer4)-1, 5000)!= HAL_OK)
{
Error_Handler();
}
#else
/* initialize the User push-button in Interrupt mode */
BSP_PB_Init(BUTTON_USER, BUTTON_MODE_EXTI);
/* Wait for User push-button press before starting the test.
In the meantime, LED3 is blinking */
while(UserButtonStatus == 0)
{
/* Toggle LED3 */
BSP_LED_Toggle(LED3);
HAL_Delay(100);
}
/*##-2- Send the wake-up from stop mode first trigger ######################*/
/* (RXNE flag setting) */
BSP_LED_On(LED3);
if(HAL_UART_Transmit(&UartHandle, (uint8_t*)aWakeUpTrigger1, COUNTOF(aWakeUpTrigger1)-1, 5000)!= HAL_OK)
{
Error_Handler();
}
/* Put UART peripheral in reception process to wait for other board
wake up confirmation */
if(HAL_UART_Receive(&UartHandle, (uint8_t *)aRxBuffer, COUNTOF(aTxBuffer1)-1, 10000) != HAL_OK)
{
Error_Handler();
}
BSP_LED_Off(LED3);
/* Compare the expected and received buffers */
if(Buffercmp((uint8_t*)aTxBuffer1,(uint8_t*)aRxBuffer,COUNTOF(aTxBuffer1)-1))
{
Error_Handler();
}
/* wait for two seconds before test second step */
HAL_Delay(2000);
/*##-3- Send the wake-up from stop mode second trigger #####################*/
/* (start Bit detection) */
BSP_LED_On(LED3);
if(HAL_UART_Transmit(&UartHandle, (uint8_t*)aWakeUpTrigger2, COUNTOF(aWakeUpTrigger2)-1, 5000)!= HAL_OK)
{
Error_Handler();
}
/* Put UART peripheral in reception process to wait for other board
wake up confirmation */
if(HAL_UART_Receive(&UartHandle, (uint8_t *)aRxBuffer, COUNTOF(aTxBuffer2)-1, 10000) != HAL_OK)
{
Error_Handler();
}
BSP_LED_Off(LED3);
/* Compare the expected and received buffers */
if(Buffercmp((uint8_t*)aTxBuffer2,(uint8_t*)aRxBuffer,COUNTOF(aTxBuffer2)-1))
{
Error_Handler();
}
/* wait for two seconds before test third step */
HAL_Delay(2000);
/*##-4- Send the wake-up from stop mode third trigger ######################*/
/* (7-bit address match) */
BSP_LED_On(LED3);
if(HAL_UART_Transmit(&UartHandle, (uint8_t*)aWakeUpTrigger3, 1, 5000)!= HAL_OK)
{
Error_Handler();
}
/* Put UART peripheral in reception process to wait for other board
wake up confirmation */
if(HAL_UART_Receive(&UartHandle, (uint8_t *)aRxBuffer, COUNTOF(aTxBuffer3)-1, 10000) != HAL_OK)
{
Error_Handler();
}
BSP_LED_Off(LED3);
/* Compare the expected and received buffers */
if(Buffercmp((uint8_t*)aTxBuffer3,(uint8_t*)aRxBuffer,COUNTOF(aTxBuffer3)-1))
{
Error_Handler();
}
/* wait for two seconds before test fourth and last step */
HAL_Delay(2000);
/*##-5- Send the wake-up from stop mode fourth trigger #####################*/
/* (4-bit address match) */
BSP_LED_On(LED3);
if(HAL_UART_Transmit(&UartHandle, (uint8_t*)aWakeUpTrigger4, 1, 5000)!= HAL_OK)
{
Error_Handler();
}
/* Put UART peripheral in reception process to wait for other board
wake up confirmation */
if(HAL_UART_Receive(&UartHandle, (uint8_t *)aRxBuffer, COUNTOF(aTxBuffer4)-1, 10000) != HAL_OK)
{
Error_Handler();
}
BSP_LED_Off(LED3);
/* Compare the expected and received buffers */
if(Buffercmp((uint8_t*)aTxBuffer4,(uint8_t*)aRxBuffer,COUNTOF(aTxBuffer4)-1))
{
Error_Handler();
}
HAL_Delay(2000);
#endif /* BOARD_IN_STOP_MODE */
/* Turn on LED3 if test passes then enter infinite loop */
BSP_LED_On(LED3);
while (1)
{
}
}
/*******************************************************************************
* Function Name : main
* Description : Main program
* Input : None
* Output : None
* Return : None
*******************************************************************************/
int main(void)
{
#ifdef DEBUG
debug();
#endif
/* System clocks configuration ---------------------------------------------*/
RCC_Configuration();
/* NVIC configuration ------------------------------------------------------*/
NVIC_Configuration();
/* GPIO configuration ------------------------------------------------------*/
GPIO_Configuration();
/* 1st phase: SPI1 Master and SPI2 Slave */
/* SPI1 Config -------------------------------------------------------------*/
SPI_InitStructure.SPI_Direction = SPI_Direction_2Lines_FullDuplex;
SPI_InitStructure.SPI_Mode = SPI_Mode_Master;
SPI_InitStructure.SPI_DataSize = SPI_DataSize_8b;
SPI_InitStructure.SPI_CPOL = SPI_CPOL_Low;
SPI_InitStructure.SPI_CPHA = SPI_CPHA_2Edge;
SPI_InitStructure.SPI_NSS = SPI_NSS_Soft;
SPI_InitStructure.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_4;
SPI_InitStructure.SPI_FirstBit = SPI_FirstBit_LSB;
SPI_InitStructure.SPI_CRCPolynomial = 7;
SPI_Init(SPI1, &SPI_InitStructure);
/* SPI2 Config -------------------------------------------------------------*/
SPI_InitStructure.SPI_Mode = SPI_Mode_Slave;
SPI_Init(SPI2, &SPI_InitStructure);
/* Enable SPI1 */
SPI_Cmd(SPI1, ENABLE);
/* Enable SPI2 */
SPI_Cmd(SPI2, ENABLE);
/* Transfer procedure */
while (TxIdx < BufferSize)
{
/* Wait for SPI1 Tx buffer empty */
while (SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_TXE) == RESET);
/* Send SPI2 data */
SPI_I2S_SendData(SPI2, SPI2_Buffer_Tx[TxIdx]);
/* Send SPI1 data */
SPI_I2S_SendData(SPI1, SPI1_Buffer_Tx[TxIdx++]);
/* Wait for SPI2 data reception */
while (SPI_I2S_GetFlagStatus(SPI2, SPI_I2S_FLAG_RXNE) == RESET);
/* Read SPI2 received data */
SPI2_Buffer_Rx[RxIdx] = SPI_I2S_ReceiveData(SPI2);
/* Wait for SPI1 data reception */
while (SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_RXNE) == RESET);
/* Read SPI1 received data */
SPI1_Buffer_Rx[RxIdx++] = SPI_I2S_ReceiveData(SPI1);
}
/* Check the corectness of written dada */
TransferStatus1 = Buffercmp(SPI2_Buffer_Rx, SPI1_Buffer_Tx, BufferSize);
TransferStatus2 = Buffercmp(SPI1_Buffer_Rx, SPI2_Buffer_Tx, BufferSize);
/* TransferStatus1, TransferStatus2 = PASSED, if the transmitted and received data
are equal */
/* TransferStatus1, TransferStatus2 = FAILED, if the transmitted and received data
are different */
/* 2nd phase: SPI1 Slave and SPI2 Master */
/* SPI1 Re-configuration ---------------------------------------------------*/
SPI_InitStructure.SPI_Mode = SPI_Mode_Slave;
SPI_Init(SPI1, &SPI_InitStructure);
/* SPI2 Re-configuration ---------------------------------------------------*/
SPI_InitStructure.SPI_Mode = SPI_Mode_Master;
SPI_Init(SPI2, &SPI_InitStructure);
/* Reset TxIdx, RxIdx indexes and receive tables values */
TxIdx = 0;
RxIdx = 0;
for (k = 0; k < BufferSize; k++) SPI2_Buffer_Rx[k] = 0;
for (k = 0; k < BufferSize; k++) SPI1_Buffer_Rx[k] = 0;
/* Transfer procedure */
while (TxIdx < BufferSize)
{
/* Wait for SPI2 Tx buffer empty */
while (SPI_I2S_GetFlagStatus(SPI2, SPI_I2S_FLAG_TXE) == RESET);
/* Send SPI1 data */
SPI_I2S_SendData(SPI1, SPI1_Buffer_Tx[TxIdx]);
/* Send SPI2 data */
SPI_I2S_SendData(SPI2, SPI2_Buffer_Tx[TxIdx++]);
/* Wait for SPI1 data reception */
while (SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_RXNE) == RESET);
/* Read SPI1 received data */
SPI1_Buffer_Rx[RxIdx] = SPI_I2S_ReceiveData(SPI1);
/* Wait for SPI2 data reception */
while (SPI_I2S_GetFlagStatus(SPI2, SPI_I2S_FLAG_RXNE) == RESET);
/* Read SPI2 received data */
SPI2_Buffer_Rx[RxIdx++] = SPI_I2S_ReceiveData(SPI2);
}
/* Check the corectness of written dada */
TransferStatus3 = Buffercmp(SPI2_Buffer_Rx, SPI1_Buffer_Tx, BufferSize);
TransferStatus4 = Buffercmp(SPI1_Buffer_Rx, SPI2_Buffer_Tx, BufferSize);
/* TransferStatus3, TransferStatus4 = PASSED, if the transmitted and received data
are equal */
/* TransferStatus3, TransferStatus4 = FAILED, if the transmitted and received data
are different */
while (1)
{}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32f10x_xx.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32f10x.c file
*/
/* System Clocks Configuration */
RCC_Configuration();
/* Configure the GPIO ports */
GPIO_Configuration();
/* Configure the DMA */
DMA_Configuration();
/* USARTy and USARTz configuration ------------------------------------------------------*/
/* USARTy and USARTz configured as follow:
- BaudRate = 230400 baud
- Word Length = 8 Bits
- One Stop Bit
- No parity
- Hardware flow control disabled (RTS and CTS signals)
- Receive and transmit enabled
*/
USART_InitStructure.USART_BaudRate = 230400;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
/* Configure USARTy */
USART_Init(USARTy, &USART_InitStructure);
/* Configure USARTz */
USART_Init(USARTz, &USART_InitStructure);
/* Enable USARTy DMA Rx and TX request */
USART_DMACmd(USARTy, USART_DMAReq_Rx | USART_DMAReq_Tx, ENABLE);
/* Enable USARTz DMA Rx and TX request */
USART_DMACmd(USARTz, USART_DMAReq_Rx | USART_DMAReq_Tx, ENABLE);
/* Enable USARTy TX DMA1 Channel */
DMA_Cmd(USARTy_Tx_DMA_Channel, ENABLE);
/* Enable USARTy RX DMA1 Channel */
DMA_Cmd(USARTy_Rx_DMA_Channel, ENABLE);
/* Enable USARTz TX DMA1 Channel */
DMA_Cmd(USARTz_Tx_DMA_Channel, ENABLE);
/* Enable USARTz RX DMA1 Channel */
DMA_Cmd(USARTz_Rx_DMA_Channel, ENABLE);
/* Enable the USARTy */
USART_Cmd(USARTy, ENABLE);
/* Enable the USARTz */
USART_Cmd(USARTz, ENABLE);
/* Wait until USARTy TX DMA1 Channel Transfer Complete */
while (DMA_GetFlagStatus(USARTy_Tx_DMA_FLAG) == RESET)
{
}
/* Wait until USARTy RX DMA1 Channel Transfer Complete */
while (DMA_GetFlagStatus(USARTy_Rx_DMA_FLAG) == RESET)
{
}
/* Wait until USARTz TX DMA1 Channel Transfer Complete */
while (DMA_GetFlagStatus(USARTz_Tx_DMA_FLAG) == RESET)
{
}
/* Wait until USARTz RX DMA1 Channel Transfer Complete */
while (DMA_GetFlagStatus(USARTz_Rx_DMA_FLAG) == RESET)
{
}
/* Check the received data with the send ones */
TransferStatus1 = Buffercmp(TxBuffer2, RxBuffer1, TxBufferSize2);
/* TransferStatus1 = PASSED, if the data transmitted from USARTz and
received by USARTy are the same */
/* TransferStatus1 = FAILED, if the data transmitted from USARTz and
received by USARTy are different */
TransferStatus2 = Buffercmp(TxBuffer1, RxBuffer2, TxBufferSize1);
/* TransferStatus2 = PASSED, if the data transmitted from USARTy and
received by USARTz are the same */
/* TransferStatus2 = FAILED, if the data transmitted from USARTy and
received by USARTz are different */
while (1)
{
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
files (startup_stm32f40_41xxx.s/startup_stm32f427_437xx.s/startup_stm32f429_439xx.s)
before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32f4xx.c file
*/
/* USART configuration -----------------------------------------------------*/
USART_Config();
/* SysTick configuration ---------------------------------------------------*/
SysTickConfig();
/* LEDs configuration ------------------------------------------------------*/
STM_EVAL_LEDInit(LED1);
STM_EVAL_LEDInit(LED2);
STM_EVAL_LEDInit(LED3);
#ifdef USART_TRANSMITTER
/* Tamper Button Configuration ---------------------------------------------*/
STM_EVAL_PBInit(BUTTON_TAMPER,BUTTON_MODE_GPIO);
/* Enable DMA USART TX Stream */
DMA_Cmd(USARTx_TX_DMA_STREAM,ENABLE);
/* Wait until Tamper Button is pressed */
while (STM_EVAL_PBGetState(BUTTON_TAMPER));
/* Enable USART DMA TX Requsts */
USART_DMACmd(USARTx, USART_DMAReq_Tx, ENABLE);
/* Waiting the end of Data transfer */
while (USART_GetFlagStatus(USARTx,USART_FLAG_TC)==RESET);
while (DMA_GetFlagStatus(USARTx_TX_DMA_STREAM,USARTx_TX_DMA_FLAG_TCIF)==RESET);
/* Clear DMA Transfer Complete Flags */
DMA_ClearFlag(USARTx_TX_DMA_STREAM,USARTx_TX_DMA_FLAG_TCIF);
/* Clear USART Transfer Complete Flags */
USART_ClearFlag(USARTx,USART_FLAG_TC);
#endif /* USART_TRANSMITTER */
#ifdef USART_RECEIVER
/* Enable DMA USART RX Stream */
DMA_Cmd(USARTx_RX_DMA_STREAM,ENABLE);
/* Enable USART DMA RX Requsts */
USART_DMACmd(USARTx, USART_DMAReq_Rx, ENABLE);
/* Waiting the end of Data transfer */
while (USART_GetFlagStatus(USARTx,USART_FLAG_TC)==RESET);
while (DMA_GetFlagStatus(USARTx_RX_DMA_STREAM,USARTx_RX_DMA_FLAG_TCIF)==RESET);
/* Clear DMA Transfer Complete Flags */
DMA_ClearFlag(USARTx_RX_DMA_STREAM,USARTx_RX_DMA_FLAG_TCIF);
/* Clear USART Transfer Complete Flags */
USART_ClearFlag(USARTx,USART_FLAG_TC);
if (Buffercmp(aTxBuffer, aRxBuffer, BUFFERSIZE) != FAILED)
{
/* Turn ON LED2 */
STM_EVAL_LEDOn(LED2);
}
else
{
/* Turn ON LED3 */
STM_EVAL_LEDOn(LED3);
}
#endif /* USART_RECEIVER */
while (1)
{
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32F3xx HAL library initialization:
- Configure the Flash prefetch
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Set NVIC Group Priority to 4
- Low Level Initialization
*/
HAL_Init();
/* Configure the system clock to 72 MHz */
SystemClock_Config();
/* Configure LED1 and LED3 */
BSP_LED_Init(LED1);
BSP_LED_Init(LED3);
/*##-1- Configure the I2C peripheral ######################################*/
I2cHandle.Instance = I2Cx;
I2cHandle.Init.Timing = I2C_TIMING;
I2cHandle.Init.OwnAddress1 = I2C_ADDRESS;
I2cHandle.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT;
I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
I2cHandle.Init.OwnAddress2 = 0xFF;
I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
I2cHandle.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE;
if(HAL_I2C_Init(&I2cHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
/* Enable the Analog I2C Filter */
HAL_I2CEx_ConfigAnalogFilter(&I2cHandle,I2C_ANALOGFILTER_ENABLE);
#ifdef MASTER_BOARD
/* Configure Key Button*/
BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_GPIO);
/* Wait for Key Button press before starting the Communication */
while (BSP_PB_GetState(BUTTON_KEY) != GPIO_PIN_RESET)
{
}
/* Wait for Key Button release before starting the Communication */
while (BSP_PB_GetState(BUTTON_KEY) != GPIO_PIN_SET)
{
}
while(1)
{
/* Initialize number of data variables */
hTxNumData = TXBUFFERSIZE;
hRxNumData = RXBUFFERSIZE;
/* Update bTransferRequest to send buffer write request for Slave */
bTransferRequest = MASTER_REQ_WRITE;
/*##-2- Master sends write request for slave #############################*/
while(HAL_I2C_Master_Transmit_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)&bTransferRequest, 1)!= HAL_OK)
{
/* Error_Handler() function is called when Timout error occurs.
When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-3- Master sends number of data to be written ########################*/
while(HAL_I2C_Master_Transmit_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)&hTxNumData, 2)!= HAL_OK)
{
/* Error_Handler() function is called when Timout error occurs.
When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-4- Master sends aTxBuffer to slave ##################################*/
while(HAL_I2C_Master_Transmit_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
{
/* Error_Handler() function is called when Timout error occurs.
When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/* Update bTransferRequest to send buffer read request for Slave */
bTransferRequest = MASTER_REQ_READ;
/*##-5- Master sends read request for slave ##############################*/
while(HAL_I2C_Master_Transmit_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)&bTransferRequest, 1)!= HAL_OK)
{
/* Error_Handler() function is called when Timout error occurs.
When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-6- Master sends number of data to be read ###########################*/
while(HAL_I2C_Master_Transmit_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)&hRxNumData, 2)!= HAL_OK)
{
/* Error_Handler() function is called when Timout error occurs.
When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-7- Master receives aRxBuffer from slave #############################*/
while(HAL_I2C_Master_Receive_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)aRxBuffer, RXBUFFERSIZE)!= HAL_OK)
{
/* Error_Handler() function is called when Timout error occurs.
When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/* Check correctness of received buffer ##################################*/
if(Buffercmp((uint8_t*)aTxBuffer,(uint8_t*)aRxBuffer,hRxNumData))
{
/* Processing Error */
Error_Handler();
}
/* Flush Rx buffers */
Flush_Buffer((uint8_t*)aRxBuffer,RXBUFFERSIZE);
/* Toggle LED1 */
BSP_LED_Toggle(LED1);
/* This delay permit the key to see LED3 toggling */
HAL_Delay(25);
}
#else
while(1)
{
/* Initialize number of data variables */
hTxNumData = 0;
hRxNumData = 0;
/*##-2- Slave receive request from master ################################*/
while(HAL_I2C_Slave_Receive_IT(&I2cHandle, (uint8_t*)&bTransferRequest, 1)!= HAL_OK)
{
}
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/* If master request write operation #####################################*/
if (bTransferRequest == MASTER_REQ_WRITE)
{
/*##-3- Slave receive number of data to be read ########################*/
while(HAL_I2C_Slave_Receive_IT(&I2cHandle, (uint8_t*)&hRxNumData, 2)!= HAL_OK);
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-4- Slave receives aRxBuffer from master ###########################*/
while(HAL_I2C_Slave_Receive_IT(&I2cHandle, (uint8_t*)aRxBuffer, hRxNumData)!= HAL_OK);
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/* Check correctness of received buffer ################################*/
if(Buffercmp((uint8_t*)aTxBuffer,(uint8_t*)aRxBuffer,hRxNumData))
{
/* Processing Error */
Error_Handler();
}
/* Flush Rx buffers */
Flush_Buffer((uint8_t*)aRxBuffer,RXBUFFERSIZE);
/* Toggle LED1 */
BSP_LED_Toggle(LED1);
}
/* If master request write operation #####################################*/
else
{
/*##-3- Slave receive number of data to be written #####################*/
while(HAL_I2C_Slave_Receive_IT(&I2cHandle, (uint8_t*)&hTxNumData, 2)!= HAL_OK);
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-4- Slave transmit aTxBuffer to master #############################*/
while(HAL_I2C_Slave_Transmit_IT(&I2cHandle, (uint8_t*)aTxBuffer, RXBUFFERSIZE)!= HAL_OK);
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
}
}
#endif /* MASTER_BOARD */
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32F0xx HAL library initialization:
- Configure the Flash prefetch
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Low Level Initialization
*/
HAL_Init();
/* Configure LED2 */
BSP_LED_Init(LED2);
/* Configure the system clock to 48 MHz */
SystemClock_Config();
/*##-1- Configure the UART peripheral ######################################*/
/* Put the USART peripheral in the Asynchronous mode (UART Mode) */
/* UART configured as follows:
- Word Length = 8 Bits
- Stop Bit = One Stop bit
- Parity = None
- BaudRate = 9600 baud
- Hardware flow control disabled (RTS and CTS signals) */
UartHandle.Instance = USARTx;
UartHandle.Init.BaudRate = 9600;
UartHandle.Init.WordLength = UART_WORDLENGTH_8B;
UartHandle.Init.StopBits = UART_STOPBITS_1;
UartHandle.Init.Parity = UART_PARITY_NONE;
UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE;
UartHandle.Init.Mode = UART_MODE_TX_RX;
UartHandle.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;
if(HAL_UART_DeInit(&UartHandle) != HAL_OK)
{
Error_Handler();
}
if(HAL_UART_Init(&UartHandle) != HAL_OK)
{
Error_Handler();
}
#ifdef TRANSMITTER_BOARD
/* Configure User push-button in Interrupt mode */
BSP_PB_Init(BUTTON_USER, BUTTON_MODE_EXTI);
/* Wait for User push-button press before starting the Communication.
In the meantime, LED2 is blinking */
while(UserButtonStatus == 0)
{
/* Toggle LED2*/
BSP_LED_Toggle(LED2);
HAL_Delay(100);
}
BSP_LED_Off(LED2);
/* The board sends the message and expects to receive it back */
/*##-2- Start the transmission process #####################################*/
/* While the UART in reception process, user can transmit data through
"aTxBuffer" buffer */
if(HAL_UART_Transmit(&UartHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE, 5000)!= HAL_OK)
{
Error_Handler();
}
/*##-3- Put UART peripheral in reception process ###########################*/
if(HAL_UART_Receive(&UartHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE, 5000) != HAL_OK)
{
Error_Handler();
}
#else
/* The board receives the message and sends it back */
/*##-2- Put UART peripheral in reception process ###########################*/
if(HAL_UART_Receive(&UartHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE, 0x1FFFFFF) != HAL_OK)
{
Error_Handler();
}
/*##-3- Start the transmission process #####################################*/
/* While the UART in reception process, user can transmit data through
"aTxBuffer" buffer */
if(HAL_UART_Transmit(&UartHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE, 5000)!= HAL_OK)
{
Error_Handler();
}
#endif /* TRANSMITTER_BOARD */
/*##-4- Compare the sent and received buffers ##############################*/
if(Buffercmp((uint8_t*)aTxBuffer,(uint8_t*)aRxBuffer,RXBUFFERSIZE))
{
Error_Handler();
}
/* Turn on LED2 if test passes then enter infinite loop */
BSP_LED_On(LED2);
/* Infinite loop */
while (1)
{
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32F103xG HAL library initialization:
- Configure the Flash prefetch
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Set NVIC Group Priority to 4
- Low Level Initialization
*/
HAL_Init();
/* Configure the system clock to 72 MHz */
SystemClock_Config();
/* Configure LED1 and LED3 */
BSP_LED_Init(LED1);
BSP_LED_Init(LED3);
/*##-1- Configure the I2C peripheral ######################################*/
I2cHandle.Instance = I2Cx;
I2cHandle.Init.ClockSpeed = I2C_SPEEDCLOCK;
I2cHandle.Init.DutyCycle = I2C_DUTYCYCLE;
I2cHandle.Init.OwnAddress1 = I2C_ADDRESS;
I2cHandle.Init.AddressingMode = I2C_ADDRESSINGMODE_10BIT;
I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
I2cHandle.Init.OwnAddress2 = 0xFF;
I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
I2cHandle.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE;
if(HAL_I2C_Init(&I2cHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
#ifdef MASTER_BOARD
/* Configure Key push-button */
BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_GPIO);
/* Wait for Key push-button press before starting the Communication */
while (BSP_PB_GetState(BUTTON_KEY) != GPIO_PIN_RESET)
{
}
/* Wait for Key push-button release before starting the Communication */
while (BSP_PB_GetState(BUTTON_KEY) != GPIO_PIN_SET)
{
}
/* The board sends the message and expects to receive it back */
/*##-2- Start the transmission process #####################################*/
/* While the I2C in reception process, user can transmit data through
"aTxBuffer" buffer */
while(HAL_I2C_Master_Transmit_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
{
/* Error_Handler() function is called when Timeout error occurs.
When Acknowledge failure occurs (Slave don't acknowledge its address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
/*##-3- Wait for the end of the transfer ###################################*/
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/* Wait for Key push-button press before starting the Communication */
while (BSP_PB_GetState(BUTTON_KEY) != GPIO_PIN_RESET)
{
}
/* Wait for Key push-button release before starting the Communication */
while (BSP_PB_GetState(BUTTON_KEY) != GPIO_PIN_SET)
{
}
/*##-4- Put I2C peripheral in reception process ###########################*/
while(HAL_I2C_Master_Receive_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
{
/* Error_Handler() function is called when Timeout error occurs.
When Acknowledge failure occurs (Slave don't acknowledge it's address)
Master restarts communication */
if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
{
Error_Handler();
}
}
#else
/* The board receives the message and sends it back */
/*##-2- Put I2C peripheral in reception process ###########################*/
if(HAL_I2C_Slave_Receive_IT(&I2cHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
{
/* Transfer error in reception process */
Error_Handler();
}
/*##-3- Wait for the end of the transfer ###################################*/
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-4- Start the transmission process #####################################*/
/* While the I2C in reception process, user can transmit data through
"aTxBuffer" buffer */
if(HAL_I2C_Slave_Transmit_IT(&I2cHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
{
/* Transfer error in transmission process */
Error_Handler();
}
#endif /* MASTER_BOARD */
/*##-5- Wait for the end of the transfer ###################################*/
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-6- Compare the sent and received buffers ##############################*/
if(Buffercmp((uint8_t*)aTxBuffer,(uint8_t*)aRxBuffer,RXBUFFERSIZE))
{
/* Processing Error */
Error_Handler();
}
/* Infinite loop */
while (1)
{
}
}
/**
* @brief Main program.
* @param None
* @retval None
*/
int main(void)
{
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32f0xx.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32f0xx.c file
*/
/* USART configuration -----------------------------------------------------*/
USART_Config();
/* SysTick configuration ---------------------------------------------------*/
SysTickConfig();
/* Initialize LEDs mounted on EVAL board */
STM_EVAL_LEDInit(LED1);
STM_EVAL_LEDInit(LED2);
STM_EVAL_LEDInit(LED3);
STM_EVAL_LEDInit(LED4);
/* Initialize push-buttons mounted on EVAL board */
STM_EVAL_PBInit(BUTTON_RIGHT, BUTTON_MODE_GPIO);
STM_EVAL_PBInit(BUTTON_LEFT, BUTTON_MODE_GPIO);
STM_EVAL_PBInit(BUTTON_UP, BUTTON_MODE_GPIO);
STM_EVAL_PBInit(BUTTON_DOWN, BUTTON_MODE_GPIO);
STM_EVAL_PBInit(BUTTON_SEL, BUTTON_MODE_GPIO);
while (1)
{
/* Clear Buffers */
Fill_Buffer(CmdBuffer, 0x02);
Fill_Buffer(AckBuffer, 0x02);
Fill_Buffer(RxBuffer, TXBUFFERSIZE);
/* Waiting transaction code in case of USART receiver */
/* DMA channel Rx of USART Configuration */
DMA_DeInit(USARTx_RX_DMA_CHANNEL);
DMA_InitStructure.DMA_PeripheralBaseAddr = USARTx_RDR_ADDRESS;
DMA_InitStructure.DMA_BufferSize = (uint16_t)2;
DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)CmdBuffer;
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC;
DMA_InitStructure.DMA_Priority = DMA_Priority_Low;
DMA_Init(USARTx_RX_DMA_CHANNEL, &DMA_InitStructure);
/* Enable the USART Rx DMA request */
USART_DMACmd(USARTx, USART_DMAReq_Rx, ENABLE);
/* Enable the DMA channel */
DMA_Cmd(USARTx_RX_DMA_CHANNEL, ENABLE);
PressedButton = Read_Joystick();
/* Waiting Joystick pressed in case to transmit data or received Transaction command */
while((PressedButton == JOY_NONE) && (CmdBuffer[0x00] == 0x00))
{
PressedButton = Read_Joystick();
}
/* USART in Mode Transmitter ---------------------------------------------*/
if ((PressedButton != JOY_NONE) && (CmdBuffer[0x00] == 0x00))
{
/* Configure the USART to receive the ACK command Table */
/* DMA channel Rx of USART Configuration */
DMA_DeInit(USARTx_RX_DMA_CHANNEL);
DMA_InitStructure.DMA_PeripheralBaseAddr = USARTx_RDR_ADDRESS;
DMA_InitStructure.DMA_BufferSize = (uint16_t)2;
DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)AckBuffer;
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC;
DMA_InitStructure.DMA_Priority = DMA_Priority_Low;
DMA_Init(USARTx_RX_DMA_CHANNEL, &DMA_InitStructure);
/* Configure the USART to send the command table */
/* DMA channel Tx of USART Configuration */
DMA_DeInit(USARTx_TX_DMA_CHANNEL);
DMA_InitStructure.DMA_PeripheralBaseAddr = USARTx_TDR_ADDRESS;
DMA_InitStructure.DMA_BufferSize = (uint16_t)2;
DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)CmdBuffer;
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralDST;
DMA_InitStructure.DMA_Priority = DMA_Priority_High;
DMA_Init(USARTx_TX_DMA_CHANNEL, &DMA_InitStructure);
switch (PressedButton)
{
/* JOY_RIGHT button pressed */
case JOY_RIGHT:
CmdBuffer[0x00] = CMD_RIGHT;
CmdBuffer[0x01] = CMD_RIGHT_SIZE;
break;
/* JOY_LEFT button pressed */
case JOY_LEFT:
CmdBuffer[0x00] = CMD_LEFT;
CmdBuffer[0x01] = CMD_LEFT_SIZE;
break;
/* JOY_UP button pressed */
case JOY_UP:
CmdBuffer[0x00] = CMD_UP;
CmdBuffer[0x01] = CMD_UP_SIZE;
break;
/* JOY_DOWN button pressed */
case JOY_DOWN:
CmdBuffer[0x00] = CMD_DOWN;
CmdBuffer[0x01] = CMD_DOWN_SIZE;
break;
/* JOY_SEL button pressed */
case JOY_SEL:
CmdBuffer[0x00] = CMD_SEL;
CmdBuffer[0x01] = CMD_SEL_SIZE;
break;
default:
break;
}
/* Enable the USART DMA requests */
USART_DMACmd(USARTx, USART_DMAReq_Rx, ENABLE);
USART_DMACmd(USARTx, USART_DMAReq_Tx, ENABLE);
/* Clear the TC bit in the SR register by writing 0 to it */
USART_ClearFlag(USARTx, USART_FLAG_TC);
/* Enable the DMA USART Tx Channel */
DMA_Cmd(USARTx_TX_DMA_CHANNEL, ENABLE);
/* Enable the DMA USART Rx channel */
DMA_Cmd(USARTx_RX_DMA_CHANNEL, ENABLE);
/* Wait the USART DMA Tx transfer complete or time out */
TimeOut = USER_TIMEOUT;
while ((DMA_GetFlagStatus(USARTx_TX_DMA_FLAG_TC) == RESET)&&(TimeOut != 0x00))
{
}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* The software must wait until TC=1. The TC flag remains cleared during all data
transfers and it is set by hardware at the last frame’s end of transmission*/
TimeOut = USER_TIMEOUT;
while ((USART_GetFlagStatus(USARTx, USART_FLAG_TC) == RESET)&&(TimeOut != 0x00))
{
}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Wait the USART DMA Rx transfer complete or time out */
TimeOut = USER_TIMEOUT;
while ((DMA_GetFlagStatus(USARTx_RX_DMA_FLAG_TC) == RESET)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Clear DMA1 global flags */
DMA_ClearFlag(USARTx_TX_DMA_FLAG_GL);
DMA_ClearFlag(USARTx_RX_DMA_FLAG_GL);
/* Disable the DMA channels */
DMA_Cmd(USARTx_TX_DMA_CHANNEL, DISABLE);
DMA_Cmd(USARTx_RX_DMA_CHANNEL, DISABLE);
/* Disable the USART Tx DMA request */
USART_DMACmd(USARTx, USART_DMAReq_Tx, DISABLE);
/* Disable the USART Rx DMA requests */
USART_DMACmd(USARTx, USART_DMAReq_Rx, DISABLE);
/* DMA channel Tx of USART Configuration */
DMA_DeInit(USARTx_TX_DMA_CHANNEL);
DMA_InitStructure.DMA_PeripheralBaseAddr = USARTx_TDR_ADDRESS;
DMA_InitStructure.DMA_BufferSize = (uint16_t)CmdBuffer[0x01];
DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)TxBuffer;
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralDST;
DMA_InitStructure.DMA_Priority = DMA_Priority_High;
DMA_Init(USARTx_TX_DMA_CHANNEL, &DMA_InitStructure);
USART_DMACmd(USARTx, USART_DMAReq_Tx, ENABLE);
/* Clear the TC bit in the SR register by writing 0 to it */
USART_ClearFlag(USARTx, USART_FLAG_TC);
/* Enable DMA1 USART Tx Channel */
DMA_Cmd(USARTx_TX_DMA_CHANNEL, ENABLE);
/* Wait the USART DMA Tx transfer complete or time out */
TimeOut = USER_TIMEOUT;
while ((DMA_GetFlagStatus(USARTx_TX_DMA_FLAG_TC) == RESET)&&(TimeOut != 0x00))
{
}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* The software must wait until TC=1. The TC flag remains cleared during all data
transfers and it is set by hardware at the last frame’s end of transmission*/
TimeOut = USER_TIMEOUT;
while ((USART_GetFlagStatus(USARTx, USART_FLAG_TC) == RESET)&&(TimeOut != 0x00))
{
}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Clear DMA global flags */
DMA_ClearFlag(USARTx_TX_DMA_FLAG_GL);
DMA_ClearFlag(USARTx_RX_DMA_FLAG_GL);
DMA_Cmd(USARTx_TX_DMA_CHANNEL, DISABLE);
/* Disable the USART Tx DMA requests */
USART_DMACmd(USARTx, USART_DMAReq_Tx, DISABLE);
CmdBuffer[0x00] = 0x00;
}
/* USART in Mode Receiver-------------------------------------------------*/
/* USART Receive Transaction command and the number of Bytes to receive */
if (CmdBuffer[0x00] != 0x00)
{
/* Wait the USART DMA Rx transfer complete or time out */
TimeOut = USER_TIMEOUT;
while ((DMA_GetFlagStatus(USARTx_RX_DMA_FLAG_TC) == RESET)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Clear DMA1 global flags */
DMA_ClearFlag(USARTx_TX_DMA_FLAG_GL);
DMA_ClearFlag(USARTx_RX_DMA_FLAG_GL);
/* Disable the DMA channels */
DMA_Cmd(USARTx_RX_DMA_CHANNEL, DISABLE);
/* Disable the USART Rx DMA requests */
USART_DMACmd(USARTx, USART_DMAReq_Rx, DISABLE);
/* At this Steep the USART send the ACK command (after Receive the transaction
command and the number of data to receive this parameter is mandatory
to configure the DMA_BufferSize in the second reception phase */
AckBuffer[0x00] = CmdBuffer[0x00];
AckBuffer[0x01] = CMD_ACK;
/* DMA channel Tx of USART Configuration */
DMA_DeInit(USARTx_TX_DMA_CHANNEL);
DMA_InitStructure.DMA_PeripheralBaseAddr = USARTx_TDR_ADDRESS;
DMA_InitStructure.DMA_BufferSize = (uint16_t)2;
DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)AckBuffer;
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralDST;
DMA_InitStructure.DMA_Priority = DMA_Priority_High;
DMA_Init(USARTx_TX_DMA_CHANNEL, &DMA_InitStructure);
USART_DMACmd(USARTx, USART_DMAReq_Tx, ENABLE);
/* Clear the TC bit in the SR register by writing 0 to it */
USART_ClearFlag(USARTx, USART_FLAG_TC);
/* Enable DMA1 USART Tx Channel */
DMA_Cmd(USARTx_TX_DMA_CHANNEL, ENABLE);
/* Wait the USART DMA Tx transfer complete or time out */
TimeOut = USER_TIMEOUT;
while ((DMA_GetFlagStatus(USARTx_TX_DMA_FLAG_TC) == RESET)&&(TimeOut != 0x00))
{}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* The software must wait until TC=1. The TC flag remains cleared during all data
transfers and it is set by hardware at the last frame’s end of transmission*/
TimeOut = USER_TIMEOUT;
while ((USART_GetFlagStatus(USARTx, USART_FLAG_TC) == RESET)&&(TimeOut != 0x00))
{
}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Clear DMA1 global flags */
DMA_ClearFlag(USARTx_TX_DMA_FLAG_GL);
DMA_ClearFlag(USARTx_RX_DMA_FLAG_GL);
DMA_Cmd(USARTx_TX_DMA_CHANNEL, DISABLE);
/* Disable the USART Tx DMA requests */
USART_DMACmd(USARTx, USART_DMAReq_Tx, DISABLE);
/* The transmitter After receive the ACK command it sends the defined data
in his TxBuffer */
/* DMA channel Rx of USART Configuration */
DMA_DeInit(USARTx_RX_DMA_CHANNEL);
DMA_InitStructure.DMA_PeripheralBaseAddr = USARTx_RDR_ADDRESS;
DMA_InitStructure.DMA_BufferSize = (uint16_t)CmdBuffer[0x01];
DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t) RxBuffer;
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC;
DMA_InitStructure.DMA_Priority = DMA_Priority_Low;
DMA_Init(USARTx_RX_DMA_CHANNEL, &DMA_InitStructure);
USART_DMACmd(USARTx, USART_DMAReq_Rx , ENABLE);
/* Enable the DMA channel */
DMA_Cmd(USARTx_RX_DMA_CHANNEL, ENABLE);
/* Wait the USART DMA Rx transfer complete or time out */
TimeOut = USER_TIMEOUT;
while ((DMA_GetFlagStatus(USARTx_RX_DMA_FLAG_TC) == RESET)&&(TimeOut != 0x00))
{
}
if(TimeOut == 0)
{
TimeOut_UserCallback();
}
/* Clear DMA1 global flags */
DMA_ClearFlag(USARTx_TX_DMA_FLAG_GL);
DMA_ClearFlag(USARTx_RX_DMA_FLAG_GL);
/* Disable the DMA channels */
DMA_Cmd(USARTx_RX_DMA_CHANNEL, DISABLE);
/* Disable the USART Rx DMA requests */
USART_DMACmd(USARTx, USART_DMAReq_Rx, DISABLE);
switch (CmdBuffer[0x01])
{
/* CMD_RIGHT command received */
case CMD_RIGHT_SIZE:
if (Buffercmp(TxBuffer, RxBuffer, CMD_RIGHT_SIZE) != FAILED)
{
/* Turn ON LED2 and LED3 */
STM_EVAL_LEDOn(LED2);
STM_EVAL_LEDOn(LED3);
/* Turn OFF LED4 */
STM_EVAL_LEDOff(LED4);
}
break;
/* CMD_LEFT command received */
case CMD_LEFT_SIZE:
if (Buffercmp(TxBuffer, RxBuffer, CMD_LEFT_SIZE) != FAILED)
{
/* Turn ON LED4 */
STM_EVAL_LEDOn(LED4);
/* Turn OFF LED2 and LED3 */
STM_EVAL_LEDOff(LED2);
STM_EVAL_LEDOff(LED3);
}
break;
/* CMD_UP command received */
case CMD_UP_SIZE:
if (Buffercmp(TxBuffer, RxBuffer, CMD_UP_SIZE) != FAILED)
{
/* Turn ON LED2 */
STM_EVAL_LEDOn(LED2);
/* Turn OFF LED3 and LED4 */
STM_EVAL_LEDOff(LED3);
STM_EVAL_LEDOff(LED4);
}
break;
/* CMD_DOWN command received */
case CMD_DOWN_SIZE:
if (Buffercmp(TxBuffer, RxBuffer, CMD_DOWN_SIZE) != FAILED)
{
/* Turn ON LED3 */
STM_EVAL_LEDOn(LED3);
/* Turn OFF LED2 and LED4 */
STM_EVAL_LEDOff(LED2);
STM_EVAL_LEDOff(LED4);
}
break;
/* CMD_SEL command received */
case CMD_SEL_SIZE:
if (Buffercmp(TxBuffer, RxBuffer, CMD_SEL_SIZE) != FAILED)
{
/* Turn ON all LED2, LED3 and LED4 */
STM_EVAL_LEDOn(LED2);
STM_EVAL_LEDOn(LED3);
STM_EVAL_LEDOn(LED4);
}
break;
default:
break;
}
CmdBuffer[0x00] = 0x00;
}
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32F4xx HAL library initialization:
- Configure the Flash prefetch, instruction and Data caches
- Configure the Systick to generate an interrupt each 1 msec
- Set NVIC Group Priority to 4
- Global MSP (MCU Support Package) initialization
*/
HAL_Init();
/* Configure LED3 and LED4 */
BSP_LED_Init(LED3);
BSP_LED_Init(LED4);
/* Configure the system clock to 180 MHz */
SystemClock_Config();
/*##-1- Configure the UART peripheral ######################################*/
/* Put the USART peripheral in the Asynchronous mode (UART Mode) */
/* UART1 configured as follow:
- Word Length = 8 Bits
- Stop Bit = One Stop bit
- Parity = None
- BaudRate = 9600 baud
- Hardware flow control disabled (RTS and CTS signals) */
UartHandle.Instance = USARTx;
UartHandle.Init.BaudRate = 9600;
UartHandle.Init.WordLength = UART_WORDLENGTH_8B;
UartHandle.Init.StopBits = UART_STOPBITS_1;
UartHandle.Init.Parity = UART_PARITY_NONE;
UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE;
UartHandle.Init.Mode = UART_MODE_TX_RX;
UartHandle.Init.OverSampling = UART_OVERSAMPLING_16;
if(HAL_UART_Init(&UartHandle) != HAL_OK)
{
Error_Handler();
}
#ifdef TRANSMITTER_BOARD
/* Configure USER Button */
BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_GPIO);
/* Wait for USER Button press before starting the Communication */
while (BSP_PB_GetState(BUTTON_KEY) == RESET)
{
}
/* The board sends the message and expects to receive it back */
/*##-2- Start the transmission process #####################################*/
/* While the UART in reception process, user can transmit data through
"aTxBuffer" buffer */
if(HAL_UART_Transmit_DMA(&UartHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
{
Error_Handler();
}
/*##-3- Wait for the end of the transfer ###################################*/
while (UartReady != SET)
{
}
/* Reset transmission flag */
UartReady = RESET;
/* Turn LED3 Off */
BSP_LED_Off(LED3);
/*##-4- Put UART peripheral in reception process ###########################*/
if(HAL_UART_Receive_DMA(&UartHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
{
Error_Handler();
}
#else
/* The board receives the message and sends it back */
/*##-2- Put UART peripheral in reception process ###########################*/
if(HAL_UART_Receive_DMA(&UartHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
{
Error_Handler();
}
/*##-3- Wait for the end of the transfer ###################################*/
while (UartReady != SET)
{
}
/* Reset transmission flag */
UartReady = RESET;
/* Turn LED3 Off */
BSP_LED_Off(LED3);
/*##-4- Start the transmission process #####################################*/
/* While the UART in reception process, user can transmit data through
"aTxBuffer" buffer */
if(HAL_UART_Transmit_DMA(&UartHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
{
Error_Handler();
}
#endif /* TRANSMITTER_BOARD */
/*##-5- Wait for the end of the transfer ###################################*/
while (UartReady != SET)
{
}
/* Reset transmission flag */
UartReady = RESET;
/*##-6- Compare the sent and received buffers ##############################*/
if(Buffercmp((uint8_t*)aTxBuffer,(uint8_t*)aRxBuffer,RXBUFFERSIZE))
{
Error_Handler();
}
/* Infinite loop */
while (1)
{
/* Toggle LED3 */
BSP_LED_Toggle(LED3);
/* Wait for 40ms */
HAL_Delay(40);
}
}
/*******************************************************************************
* Function Name : main
* Description : Main program
* Input : None
* Output : None
* Return : None
*******************************************************************************/
int main()
{
#ifdef DEBUG
debug();
#endif
SCU_MCLKSourceConfig(SCU_MCLK_OSC); /*Use OSC as the default clock source*/
SCU_PCLKDivisorConfig(SCU_PCLK_Div1); /* ARM Peripheral bus clokdivisor = 1*/
/* SCU configuration */
SCU_Configuration();
/* GPIO pins configuration */
GPIO_Configuration();
/* SSP0 configuration */
SSP_DeInit(SSP0);
SSP_InitStructure.SSP_FrameFormat = SSP_FrameFormat_Motorola;
SSP_InitStructure.SSP_Mode = SSP_Mode_Master;
SSP_InitStructure.SSP_CPOL = SSP_CPOL_High;
SSP_InitStructure.SSP_CPHA = SSP_CPHA_2Edge;
SSP_InitStructure.SSP_DataSize = SSP_DataSize_8b;
SSP_InitStructure.SSP_ClockRate = 5;
SSP_InitStructure.SSP_ClockPrescaler = 2;
SSP_Init(SSP0, &SSP_InitStructure);
/* SSP1 configuration */
SSP_DeInit(SSP1);
SSP_InitStructure.SSP_Mode = SSP_Mode_Slave;
SSP_InitStructure.SSP_SlaveOutput = SSP_SlaveOutput_Enable;
SSP_Init(SSP1, &SSP_InitStructure);
/* SSP0 enable */
SSP_Cmd(SSP0, ENABLE);
/* SSP1 enable */
SSP_Cmd(SSP1, ENABLE);
/* Master to slave transfer procedure */
while(Tx_Idx<32)
{
SSP_SendData(SSP0, SSP0_Buffer_Tx[Tx_Idx++]);
while(SSP_GetFlagStatus(SSP1, SSP_FLAG_RxFifoNotEmpty)==RESET);
SSP1_Buffer_Rx[Rx_Idx++] = SSP_ReceiveData(SSP1);
}
/* Check the received data with the send ones */
TransferStatus1 = Buffercmp(SSP0_Buffer_Tx, SSP1_Buffer_Rx, 32);
/* TransferStatus = PASSED, if the data transmitted from SSP0 and
received by SSP1 are the same */
/* TransferStatus = FAILED, if the data transmitted from SSP0 and
received by SSP1 are different */
/* Clear SSP0 receive Fifo */
for(k=0; k<8; k++) SSP0_Buffer_Rx[k] = SSP_ReceiveData(SSP0);
/* Reset counters */
Tx_Idx=Rx_Idx=0;
/* Slave to master transfer procedure */
while(Tx_Idx<32)
{
SSP_SendData(SSP1, SSP1_Buffer_Tx[Tx_Idx]);
/* send a dummy bit to generate the clock */
SSP_SendData(SSP0, SSP0_Buffer_Tx[Tx_Idx++]);
while(SSP_GetFlagStatus(SSP0, SSP_FLAG_RxFifoNotEmpty)==RESET);
SSP0_Buffer_Rx[Rx_Idx++] = SSP_ReceiveData(SSP0);
}
/* Check the received data with the send ones */
TransferStatus2 = Buffercmp(SSP1_Buffer_Tx, SSP0_Buffer_Rx, 32);
/* TransferStatus = PASSED, if the data transmitted from SSP1 and
received by SSP0 are the same */
/* TransferStatus = FAILED, if the data transmitted from SSP1 and
received by SSP0 are different */
while(1);
}
