static void i2c_early_init_bus(unsigned bus)
{
ROMSTAGE_CONST struct soc_intel_skylake_config *config;
ROMSTAGE_CONST struct device *tree_dev;
const struct lpss_i2c_speed_config *sptr;
enum i2c_speed speed;
pci_devfn_t dev;
unsigned devfn;
uintptr_t base;
uint32_t value;
void *reg;
/* Find the PCI device for this bus controller */
devfn = i2c_bus_to_devfn(bus);
if (devfn < 0)
return;
/* Look up the controller device in the devicetree */
dev = PCI_DEV(0, PCI_SLOT(devfn), PCI_FUNC(devfn));
tree_dev = dev_find_slot(0, devfn);
if (!tree_dev || !tree_dev->enabled)
return;
/* Skip if not enabled for early init */
config = tree_dev->chip_info;
if (!config)
return;
if (!config->i2c[bus].early_init)
return;
/* Prepare early base address for access before memory */
base = EARLY_I2C_BASE(bus);
pci_write_config32(dev, PCI_BASE_ADDRESS_0, base);
pci_write_config32(dev, PCI_COMMAND,
PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
/* Take device out of reset */
reg = (void *)(base + SIO_REG_PPR_RESETS);
value = read32(reg);
value |= SIO_REG_PPR_RESETS_FUNC | SIO_REG_PPR_RESETS_APB |
SIO_REG_PPR_RESETS_IDMA;
write32(reg, value);
/* Initialize the controller */
speed = config->i2c[bus].speed ? : I2C_SPEED_FAST;
lpss_i2c_init(bus, speed);
/* Apply custom speed config if it has been set by the board */
for (value = 0; value < LPSS_I2C_SPEED_CONFIG_COUNT; value++) {
sptr = &config->i2c[bus].speed_config[value];
if (sptr->speed == speed) {
lpss_i2c_set_speed_config(bus, sptr);
break;
}
}
}
static void i2c_early_init_bus(unsigned int bus)
{
ROMSTAGE_CONST struct soc_intel_skylake_config *config;
ROMSTAGE_CONST struct device *tree_dev;
pci_devfn_t dev;
int devfn;
uintptr_t base;
/* Find the PCI device for this bus controller */
devfn = i2c_bus_to_devfn(bus);
if (devfn < 0)
return;
/* Look up the controller device in the devicetree */
dev = PCI_DEV(0, PCI_SLOT(devfn), PCI_FUNC(devfn));
tree_dev = dev_find_slot(0, devfn);
if (!tree_dev || !tree_dev->enabled)
return;
/* Skip if not enabled for early init */
config = tree_dev->chip_info;
if (!config)
return;
if (!config->i2c[bus].early_init)
return;
/* Prepare early base address for access before memory */
base = EARLY_I2C_BASE(bus);
pci_write_config32(dev, PCI_BASE_ADDRESS_0, base);
pci_write_config32(dev, PCI_COMMAND,
PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
/* Take device out of reset */
lpss_reset_release(base);
/* Initialize the controller */
lpss_i2c_init(bus, &config->i2c[bus]);
}
/* Get base address for early init of I2C controllers. */
uintptr_t dw_i2c_get_soc_early_base(unsigned int bus)
{
return EARLY_I2C_BASE(bus);
}
