static void system_SystickConfig(uint32_t ui32_msInterval)
{
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() * ui32_msInterval / 1000);
SysTickIntRegister(&SysTickIntHandle);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
}
void init()
{
ROM_FPUEnable();
ROM_FPULazyStackingEnable();
ROM_SysCtlClockSet(SYSCTL_SYSDIV_2_5 | SYSCTL_USE_PLL | SYSCTL_XTAL_16MHZ | SYSCTL_OSC_MAIN);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
GPIO_PORTB_DIR_R = 0x00;
GPIO_PORTB_DEN_R = 0xff;
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, LED_RED|LED_GREEN|LED_BLUE);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
ROM_GPIOPinConfigure(GPIO_PA0_U0RX);
ROM_GPIOPinConfigure(GPIO_PA1_U0TX);
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
UARTStdioInit(0);
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / 1000000);
ROM_SysTickEnable();
ROM_SysTickIntEnable();
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER0);
ROM_TimerConfigure(TIMER0_BASE, TIMER_CFG_32_BIT_PER);
reset();
}
//****************************************************************************
//
// This is the main loop that runs the application.
//
//****************************************************************************
int
main(void)
{
//
// Set the clocking to run from the PLL at 50MHz.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Set the system tick to fire 100 times per second.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Pass the USB library our device information, initialize the USB
// controller and connect the device to the bus.
//
g_psCompDevices[0].pvInstance =
USBDHIDMouseCompositeInit(0, (tUSBDHIDMouseDevice *)&g_sMouseDevice);
g_psCompDevices[1].pvInstance =
USBDCDCCompositeInit(0, (tUSBDCDCDevice *)&g_sCDCDevice);
//
// Set the USB stack mode to Device mode with VBUS monitoring.
//
USBStackModeSet(0, USB_MODE_DEVICE, 0);
//
// Pass the device information to the USB library and place the device
// on the bus.
//
USBDCompositeInit(0, &g_sCompDevice, DESCRIPTOR_DATA_SIZE,
g_pucDescriptorData);
//
// Initialize the mouse and serial devices.
//
MouseInit();
SerialInit();
//
// Drop into the main loop.
//
while(1)
{
//
// Allow the main mouse routine to run.
//
MouseMain();
//
// Allow the main serial routine to run.
//
SerialMain();
}
}
void timerInit()
{
#if F_CPU >= 80000000
ROM_SysCtlClockSet(SYSCTL_SYSDIV_2_5|SYSCTL_USE_PLL|SYSCTL_XTAL_16MHZ|
SYSCTL_OSC_MAIN);
#elif F_CPU >= 50000000
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4|SYSCTL_USE_PLL|SYSCTL_XTAL_16MHZ|
SYSCTL_OSC_MAIN);
#elif F_CPU >= 40000000
ROM_SysCtlClockSet(SYSCTL_SYSDIV_5|SYSCTL_USE_PLL|SYSCTL_XTAL_16MHZ|
SYSCTL_OSC_MAIN);
#elif F_CPU >= 25000000
ROM_SysCtlClockSet(SYSCTL_SYSDIV_8|SYSCTL_USE_PLL|SYSCTL_XTAL_16MHZ|
SYSCTL_OSC_MAIN);
#elif F_CPU >= 16200000
ROM_SysCtlClockSet(SYSCTL_SYSDIV_1|SYSCTL_USE_OSC|SYSCTL_XTAL_16MHZ|
SYSCTL_OSC_MAIN); //NOT PLL
#elif F_CPU >= 16100000
ROM_SysCtlClockSet(SYSCTL_SYSDIV_1|SYSCTL_USE_OSC|SYSCTL_OSC_INT|
SYSCTL_OSC_MAIN); //NOT PLL, INT OSC
#elif F_CPU >= 16000000
ROM_SysCtlClockSet(SYSCTL_SYSDIV_12_5|SYSCTL_USE_PLL|SYSCTL_XTAL_16MHZ|
SYSCTL_OSC_MAIN);
#elif F_CPU >= 10000000
ROM_SysCtlClockSet(SYSCTL_SYSDIV_20|SYSCTL_USE_PLL|SYSCTL_XTAL_16MHZ|
SYSCTL_OSC_MAIN);
#elif F_CPU >= 8000000
ROM_SysCtlClockSet(SYSCTL_SYSDIV_25|SYSCTL_USE_PLL|SYSCTL_XTAL_16MHZ|
SYSCTL_OSC_MAIN);
#else
ROM_SysCtlClockSet(SYSCTL_SYSDIV_2_5|SYSCTL_USE_PLL|SYSCTL_XTAL_16MHZ|
SYSCTL_OSC_MAIN);
#endif
//
// SysTick is used for delay() and delayMicroseconds()
//
// ROM_SysTickPeriodSet(0x00FFFFFF);
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / TICKS_PER_SECOND);
ROM_SysTickEnable();
//
//Initialize Timer5 to be used as time-tracker since beginning of time
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER5); //not tied to launchpad pin
ROM_TimerConfigure(TIMER5_BASE, TIMER_CFG_PERIODIC_UP);
ROM_TimerLoadSet(TIMER5_BASE, TIMER_A, ROM_SysCtlClockGet()/1000);
ROM_IntEnable(INT_TIMER5A);
ROM_TimerIntEnable(TIMER5_BASE, TIMER_TIMA_TIMEOUT);
ROM_TimerEnable(TIMER5_BASE, TIMER_A);
ROM_IntMasterEnable();
}
void initSysTick(void)
{
ROM_SysTickDisable();
ROM_SysTickPeriodSet( SYSTICK_PERIOD );
/* Write 0 to STCURRENT to clear counter */
*((volatile uint32_t *)NVIC_ST_CURRENT) = 0;
ROM_SysTickIntEnable();
ROM_SysTickEnable();
return;
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
uint32_t ui32TxCount;
uint32_t ui32RxCount;
//uint32_t ui32Loop;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run from the PLL at 50MHz
//
#if 1
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Configure the required pins for USB operation.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTD_BASE, GPIO_PIN_5 | GPIO_PIN_4);
//ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / 100);
/* This code taken from: http://e2e.ti.com/support/microcontrollers/tiva_arm/f/908/t/311237.aspx
*/
#else
#include "hw_nvic.h"
FlashErase(0x00000000);
ROM_IntMasterDisable();
ROM_SysTickIntDisable();
ROM_SysTickDisable();
uint32_t ui32SysClock;
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN | SYSCTL_XTAL_16MHZ);
ui32SysClock = ROM_SysCtlClockGet();
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTD_BASE, GPIO_PIN_4 | GPIO_PIN_5);
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / 100);
HWREG(NVIC_DIS0) = 0xffffffff;
HWREG(NVIC_DIS1) = 0xffffffff;
HWREG(NVIC_DIS2) = 0xffffffff;
HWREG(NVIC_DIS3) = 0xffffffff;
HWREG(NVIC_DIS4) = 0xffffffff;
int ui32Addr;
for(ui32Addr = NVIC_PRI0; ui32Addr <= NVIC_PRI34; ui32Addr+=4)
{
HWREG(ui32Addr) = 0;
}
HWREG(NVIC_SYS_PRI1) = 0;
HWREG(NVIC_SYS_PRI2) = 0;
HWREG(NVIC_SYS_PRI3) = 0;
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_USB0);
ROM_SysCtlPeripheralReset(SYSCTL_PERIPH_USB0);
ROM_SysCtlUSBPLLEnable();
ROM_SysCtlDelay(ui32SysClock*2 / 3);
ROM_IntMasterEnable();
ROM_UpdateUSB(0);
while(1)
{
}
#endif
#define BOOTLOADER_TEST 0
#if BOOTLOADER_TEST
#include "hw_nvic.h"
//ROM_UpdateUART();
// May need to do the following here:
// 0. See if this will cause bootloader to start
//ROM_FlashErase(0);
//ROM_UpdateUSB(0);
#define SYSTICKS_PER_SECOND 100
uint32_t ui32SysClock = ROM_SysCtlClockGet();
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//USBDCDTerm(0);
// Disable all interrupts
ROM_IntMasterDisable();
ROM_SysTickIntDisable();
ROM_SysTickDisable();
HWREG(NVIC_DIS0) = 0xffffffff;
HWREG(NVIC_DIS1) = 0xffffffff;
HWREG(NVIC_DIS2) = 0xffffffff;
HWREG(NVIC_DIS3) = 0xffffffff;
HWREG(NVIC_DIS4) = 0xffffffff;
int ui32Addr;
for(ui32Addr = NVIC_PRI0; ui32Addr <= NVIC_PRI34; ui32Addr+=4)
{
HWREG(ui32Addr) = 0;
}
HWREG(NVIC_SYS_PRI1) = 0;
HWREG(NVIC_SYS_PRI2) = 0;
HWREG(NVIC_SYS_PRI3) = 0;
// 1. Enable USB PLL
//ROM_SysCtlUSBPLLEnable();
// 2. Enable USB controller
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_USB0);
ROM_SysCtlPeripheralReset(SYSCTL_PERIPH_USB0);
//USBClockEnable(USB0_BASE, 8, USB_CLOCK_INTERNAL);
//HWREG(USB0_BASE + USB_O_CC) = (8 - 1) | USB_CLOCK_INTERNAL;
ROM_SysCtlUSBPLLEnable();
// 3. Enable USB D+ D- pins
// 4. Activate USB DFU
ROM_SysCtlDelay(ui32SysClock * 2 / 3);
ROM_IntMasterEnable(); // Re-enable interrupts at NVIC level
ROM_UpdateUSB(0);
// 5. Should never get here since update is in progress
#endif // BOOTLOADER_TEST
//
// Enable the GPIO port that is used for the on-board LED.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB); // gjs Our board uses GPIOB for LEDs
// gjs original ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
//
// Enable the GPIO pins for the LED (PF2 & PF3).
//
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTB_BASE, GPIO_PIN_0|GPIO_PIN_1);
// gjs original ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_3|GPIO_PIN_2);
//
// Not configured initially.
//
g_bUSBConfigured = false;
//
// Enable the UART that we will be redirecting.
//
ROM_SysCtlPeripheralEnable(USB_UART_PERIPH);
//
// Enable and configure the UART RX and TX pins
//
ROM_SysCtlPeripheralEnable(TX_GPIO_PERIPH);
ROM_SysCtlPeripheralEnable(RX_GPIO_PERIPH);
ROM_GPIOPinTypeUART(TX_GPIO_BASE, TX_GPIO_PIN);
ROM_GPIOPinTypeUART(RX_GPIO_BASE, RX_GPIO_PIN);
//
// TODO: Add code to configure handshake GPIOs if required.
//
//
// Set the default UART configuration.
//
ROM_UARTConfigSetExpClk(USB_UART_BASE, ROM_SysCtlClockGet(),
DEFAULT_BIT_RATE, DEFAULT_UART_CONFIG);
ROM_UARTFIFOLevelSet(USB_UART_BASE, UART_FIFO_TX4_8, UART_FIFO_RX4_8);
//
// Configure and enable UART interrupts.
//
ROM_UARTIntClear(USB_UART_BASE, ROM_UARTIntStatus(USB_UART_BASE, false));
ROM_UARTIntEnable(USB_UART_BASE, (UART_INT_OE | UART_INT_BE | UART_INT_PE |
UART_INT_FE | UART_INT_RT | UART_INT_TX | UART_INT_RX));
//
// Enable the system tick.
//
#if 0
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
#endif
//
// Initialize the transmit and receive buffers.
//
USBBufferInit(&g_sTxBuffer);
USBBufferInit(&g_sRxBuffer);
//
// Set the USB stack mode to Device mode with VBUS monitoring.
//
USBStackModeSet(0, eUSBModeDevice, 0);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDCDCInit(0, &g_sCDCDevice);
//
// Clear our local byte counters.
//
ui32RxCount = 0;
ui32TxCount = 0;
//
// Enable interrupts now that the application is ready to start.
//
ROM_IntEnable(USB_UART_INT);
// Enable FreeRTOS
mainA(); // FreeRTOS. Will not return
#if 0
//
// Main application loop.
//
while(1)
{
//
// Have we been asked to update the status display?
//
if(g_ui32Flags & COMMAND_STATUS_UPDATE)
{
//
// Clear the command flag
//
ROM_IntMasterDisable();
g_ui32Flags &= ~COMMAND_STATUS_UPDATE;
ROM_IntMasterEnable();
}
//
// Has there been any transmit traffic since we last checked?
//
if(ui32TxCount != g_ui32UARTTxCount)
{
//
// Turn on the Green LED.
//
// gjs ROM_UARTCharPutNonBlocking(USB_UART_BASE, 'b');
#if 1
if (ui32TxCount & 1) {
GPIOPinWrite(GPIO_PORTB_BASE, GPIO_PIN_0, GPIO_PIN_0);
} else {
GPIOPinWrite(GPIO_PORTB_BASE, GPIO_PIN_0, 0);
}
#else
if (1 || g_ui32UARTTxCount & 0x01) {
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, GPIO_PIN_3);
} else {
//GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, 0);
}
//
// Delay for a bit.
//
for(uint32_t ui32Loop = 0; ui32Loop < 150000; ui32Loop++)
{
}
//
// Turn off the Green LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, 0);
#endif
//
// Take a snapshot of the latest transmit count.
//
ui32TxCount = g_ui32UARTTxCount;
}
//
// Has there been any receive traffic since we last checked?
//
if(ui32RxCount != g_ui32UARTRxCount)
{
//
// Turn on the Blue LED.
//
#if 1
if (ui32RxCount & 1) {
GPIOPinWrite(GPIO_PORTB_BASE, GPIO_PIN_1, GPIO_PIN_1);
} else {
GPIOPinWrite(GPIO_PORTB_BASE, GPIO_PIN_1, 0);
}
#else
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, GPIO_PIN_2);
//
// Delay for a bit.
//
for(uint32_t ui32Loop = 0; ui32Loop < 150000; ui32Loop++)
{
}
//
// Turn off the Blue LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, 0);
#endif
//
// Take a snapshot of the latest receive count.
//
ui32RxCount = g_ui32UARTRxCount;
}
}
#endif
}
//*****************************************************************************
//
// This is the main loop that runs the application.
//
//*****************************************************************************
int
main(void)
{
//
// Turn on stacking of FPU registers if FPU is used in the ISR.
//
FPULazyStackingEnable();
//
// Set the clocking to run from the PLL at 40MHz.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_5 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Set the system tick to fire 100 times per second.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Enable the Debug UART.
//
ConfigureUART();
//
// Print the welcome message to the terminal.
//
UARTprintf("\033[2JAir Mouse Application\n");
//
// Configure desired interrupt priorities. This makes certain that the DCM
// is fed data at a consistent rate. Lower numbers equal higher priority.
//
ROM_IntPrioritySet(INT_I2C3, 0x00);
ROM_IntPrioritySet(INT_GPIOB, 0x10);
ROM_IntPrioritySet(FAULT_SYSTICK, 0x20);
ROM_IntPrioritySet(INT_UART1, 0x60);
ROM_IntPrioritySet(INT_UART0, 0x70);
ROM_IntPrioritySet(INT_WTIMER5B, 0x80);
//
// Configure the USB D+ and D- pins.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTD_BASE, GPIO_PIN_5 | GPIO_PIN_4);
//
// Pass the USB library our device information, initialize the USB
// controller and connect the device to the bus.
//
USBDHIDMouseCompositeInit(0, &g_sMouseDevice, &g_psCompDevices[0]);
USBDHIDKeyboardCompositeInit(0, &g_sKeyboardDevice, &g_psCompDevices[1]);
//
// Set the USB stack mode to Force Device mode.
//
USBStackModeSet(0, eUSBModeForceDevice, 0);
//
// Pass the device information to the USB library and place the device
// on the bus.
//
USBDCompositeInit(0, &g_sCompDevice, DESCRIPTOR_DATA_SIZE,
g_pui8DescriptorData);
//
// User Interface Init
//
ButtonsInit();
RGBInit(0);
RGBEnable();
//
// Initialize the motion sub system.
//
MotionInit();
//
// Initialize the Radio Systems.
//
LPRFInit();
//
// Drop into the main loop.
//
while(1)
{
//
// Check for and handle timer tick events.
//
if(HWREGBITW(&g_ui32Events, USB_TICK_EVENT) == 1)
{
//
// Clear the Tick event flag. Set in SysTick interrupt handler.
//
HWREGBITW(&g_ui32Events, USB_TICK_EVENT) = 0;
//
// Each tick period handle wired mouse and keyboard.
//
if(HWREGBITW(&g_ui32USBFlags, FLAG_CONNECTED) == 1)
{
MouseMoveHandler();
KeyboardMain();
}
}
//
// Check for LPRF tick events. LPRF Ticks are slower since UART to
// RNP is much slower data connection than the USB.
//
if(HWREGBITW(&g_ui32Events, LPRF_TICK_EVENT) == 1)
{
//
// Clear the event flag.
//
HWREGBITW(&g_ui32Events, LPRF_TICK_EVENT) = 0;
//
// Perform the LPRF Main task handling
//
LPRFMain();
}
//
// Check for and handle motion events.
//
if((HWREGBITW(&g_ui32Events, MOTION_EVENT) == 1) ||
(HWREGBITW(&g_ui32Events, MOTION_ERROR_EVENT) == 1))
{
//
// Clear the motion event flag. Set in the Motion I2C interrupt
// handler when an I2C transaction to get sensor data is complete.
//
HWREGBITW(&g_ui32Events, MOTION_EVENT) = 0;
//
// Process the motion data that has been captured
//
MotionMain();
}
}
}
//*****************************************************************************
//
// This example demonstrates how to use the uDMA controller to transfer data
// between memory buffers and to and from a peripheral, in this case a UART.
// The uDMA controller is configured to repeatedly transfer a block of data
// from one memory buffer to another. It is also set up to repeatedly copy a
// block of data from a buffer to the UART output. The UART data is looped
// back so the same data is received, and the uDMA controlled is configured to
// continuously receive the UART data using ping-pong buffers.
//
// The processor is put to sleep when it is not doing anything, and this allows
// collection of CPU usage data to see how much CPU is being used while the
// data transfers are ongoing.
//
//*****************************************************************************
int
main(void)
{
static uint32_t ui32PrevSeconds;
static uint32_t ui32PrevXferCount;
static uint32_t ui32PrevUARTCount = 0;
uint32_t ui32XfersCompleted;
uint32_t ui32BytesTransferred;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run from the PLL at 50 MHz.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Enable peripherals to operate when CPU is in sleep.
//
ROM_SysCtlPeripheralClockGating(true);
//
// Enable the GPIO port that is used for the on-board LED.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
//
// Enable the GPIO pins for the LED (PF2).
//
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_2);
//
// Initialize the UART.
//
ConfigureUART();
UARTprintf("\033[2JuDMA Example\n");
//
// Show the clock frequency on the display.
//
UARTprintf("Tiva C Series @ %u MHz\n\n", ROM_SysCtlClockGet() / 1000000);
//
// Show statistics headings.
//
UARTprintf("CPU Memory UART Remaining\n");
UARTprintf("Usage Transfers Transfers Time\n");
//
// Configure SysTick to occur 100 times per second, to use as a time
// reference. Enable SysTick to generate interrupts.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Initialize the CPU usage measurement routine.
//
CPUUsageInit(ROM_SysCtlClockGet(), SYSTICKS_PER_SECOND, 2);
//
// Enable the uDMA controller at the system level. Enable it to continue
// to run while the processor is in sleep.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UDMA);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UDMA);
//
// Enable the uDMA controller error interrupt. This interrupt will occur
// if there is a bus error during a transfer.
//
ROM_IntEnable(INT_UDMAERR);
//
// Enable the uDMA controller.
//
ROM_uDMAEnable();
//
// Point at the control table to use for channel control structures.
//
ROM_uDMAControlBaseSet(ui8ControlTable);
//
// Initialize the uDMA memory to memory transfers.
//
InitSWTransfer();
//
// Initialize the uDMA UART transfers.
//
InitUART1Transfer();
//
// Remember the current SysTick seconds count.
//
ui32PrevSeconds = g_ui32Seconds;
//
// Remember the current count of memory buffer transfers.
//
ui32PrevXferCount = g_ui32MemXferCount;
//
// Loop until the button is pressed. The processor is put to sleep
// in this loop so that CPU utilization can be measured.
//
while(1)
{
//
// Check to see if one second has elapsed. If so, the make some
// updates.
//
if(g_ui32Seconds != ui32PrevSeconds)
{
//
// Turn on the LED as a heartbeat
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, GPIO_PIN_2);
//
// Print a message to the display showing the CPU usage percent.
// The fractional part of the percent value is ignored.
//
UARTprintf("\r%3d%% ", g_ui32CPUUsage >> 16);
//
// Remember the new seconds count.
//
ui32PrevSeconds = g_ui32Seconds;
//
// Calculate how many memory transfers have occurred since the last
// second.
//
ui32XfersCompleted = g_ui32MemXferCount - ui32PrevXferCount;
//
// Remember the new transfer count.
//
ui32PrevXferCount = g_ui32MemXferCount;
//
// Compute how many bytes were transferred in the memory transfer
// since the last second.
//
ui32BytesTransferred = ui32XfersCompleted * MEM_BUFFER_SIZE * 4;
//
// Print a message showing the memory transfer rate.
//
if(ui32BytesTransferred >= 100000000)
{
UARTprintf("%3d MB/s ", ui32BytesTransferred / 1000000);
}
else if(ui32BytesTransferred >= 10000000)
{
UARTprintf("%2d.%01d MB/s ", ui32BytesTransferred / 1000000,
(ui32BytesTransferred % 1000000) / 100000);
}
else if(ui32BytesTransferred >= 1000000)
{
UARTprintf("%1d.%02d MB/s ", ui32BytesTransferred / 1000000,
(ui32BytesTransferred % 1000000) / 10000);
}
else if(ui32BytesTransferred >= 100000)
{
UARTprintf("%3d KB/s ", ui32BytesTransferred / 1000);
}
else if(ui32BytesTransferred >= 10000)
{
UARTprintf("%2d.%01d KB/s ", ui32BytesTransferred / 1000,
(ui32BytesTransferred % 1000) / 100);
}
else if(ui32BytesTransferred >= 1000)
{
UARTprintf("%1d.%02d KB/s ", ui32BytesTransferred / 1000,
(ui32BytesTransferred % 1000) / 10);
}
else if(ui32BytesTransferred >= 100)
{
UARTprintf("%3d B/s ", ui32BytesTransferred);
}
else if(ui32BytesTransferred >= 10)
{
UARTprintf("%2d B/s ", ui32BytesTransferred);
}
else
{
UARTprintf("%1d B/s ", ui32BytesTransferred);
}
//
// Calculate how many UART transfers have occurred since the last
// second.
//
ui32XfersCompleted = (g_ui32RxBufACount + g_ui32RxBufBCount -
ui32PrevUARTCount);
//
// Remember the new UART transfer count.
//
ui32PrevUARTCount = g_ui32RxBufACount + g_ui32RxBufBCount;
//
// Compute how many bytes were transferred by the UART. The number
// of bytes received is multiplied by 2 so that the TX bytes
// transferred are also accounted for.
//
ui32BytesTransferred = ui32XfersCompleted * UART_RXBUF_SIZE * 2;
//
// Print a message showing the UART transfer rate.
//
if(ui32BytesTransferred >= 1000000)
{
UARTprintf("%1d.%02d MB/s ", ui32BytesTransferred / 1000000,
(ui32BytesTransferred % 1000000) / 10000);
}
else if(ui32BytesTransferred >= 100000)
{
UARTprintf("%3d KB/s ", ui32BytesTransferred / 1000);
}
else if(ui32BytesTransferred >= 10000)
{
UARTprintf("%2d.%01d KB/s ", ui32BytesTransferred / 1000,
(ui32BytesTransferred % 1000) / 100);
}
else if(ui32BytesTransferred >= 1000)
{
UARTprintf("%1d.%02d KB/s ", ui32BytesTransferred / 1000,
(ui32BytesTransferred % 1000) / 10);
}
else if(ui32BytesTransferred >= 100)
{
UARTprintf("%3d B/s ", ui32BytesTransferred);
}
else if(ui32BytesTransferred >= 10)
{
UARTprintf("%2d B/s ", ui32BytesTransferred);
}
else
{
UARTprintf("%1d B/s ", ui32BytesTransferred);
}
//
// Print a spinning line to make it more apparent that there is
// something happening.
//
UARTprintf("%2ds", 10 - ui32PrevSeconds);
//
// Turn off the LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, 0);
}
//
// Put the processor to sleep if there is nothing to do. This allows
// the CPU usage routine to measure the number of free CPU cycles.
// If the processor is sleeping a lot, it can be hard to connect to
// the target with the debugger.
//
ROM_SysCtlSleep();
//
// See if we have run int32_t enough and exit the loop if so.
//
if(g_ui32Seconds >= 10)
{
break;
}
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
uint32_t ui32TxCount;
uint32_t ui32RxCount;
tRectangle sRect;
char pcBuffer[16];
uint32_t ui32Fullness;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run from the PLL at 50MHz
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Configure the required pins for USB operation.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOG);
ROM_GPIOPinConfigure(GPIO_PG4_USB0EPEN);
ROM_GPIOPinTypeUSBDigital(GPIO_PORTG_BASE, GPIO_PIN_4);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOL);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTL_BASE, GPIO_PIN_6 | GPIO_PIN_7);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTB_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// Erratum workaround for silicon revision A1. VBUS must have pull-down.
//
if(CLASS_IS_BLIZZARD && REVISION_IS_A1)
{
HWREG(GPIO_PORTB_BASE + GPIO_O_PDR) |= GPIO_PIN_1;
}
//
// Not configured initially.
//
g_bUSBConfigured = false;
//
// Initialize the display driver.
//
CFAL96x64x16Init();
//
// Initialize the graphics context.
//
GrContextInit(&g_sContext, &g_sCFAL96x64x16);
//
// Fill the top 15 rows of the screen with blue to create the banner.
//
sRect.i16XMin = 0;
sRect.i16YMin = 0;
sRect.i16XMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.i16YMax = 9;
GrContextForegroundSet(&g_sContext, ClrDarkBlue);
GrRectFill(&g_sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&g_sContext, ClrWhite);
GrRectDraw(&g_sContext, &sRect);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, g_psFontFixed6x8);
GrStringDrawCentered(&g_sContext, "usb-dev-serial", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 4, 0);
//
// Show the various static text elements on the color STN display.
//
GrStringDraw(&g_sContext, "Tx #",-1, 0, 12, false);
GrStringDraw(&g_sContext, "Tx buf", -1, 0, 22, false);
GrStringDraw(&g_sContext, "Rx #", -1, 0, 32, false);
GrStringDraw(&g_sContext, "Rx buf", -1, 0, 42, false);
DrawBufferMeter(&g_sContext, 40, 22);
DrawBufferMeter(&g_sContext, 40, 42);
//
// Enable the UART that we will be redirecting.
//
ROM_SysCtlPeripheralEnable(USB_UART_PERIPH);
//
// Enable and configure the UART RX and TX pins
//
ROM_SysCtlPeripheralEnable(TX_GPIO_PERIPH);
ROM_SysCtlPeripheralEnable(RX_GPIO_PERIPH);
ROM_GPIOPinTypeUART(TX_GPIO_BASE, TX_GPIO_PIN);
ROM_GPIOPinTypeUART(RX_GPIO_BASE, RX_GPIO_PIN);
//
// TODO: Add code to configure handshake GPIOs if required.
//
//
// Set the default UART configuration.
//
ROM_UARTConfigSetExpClk(USB_UART_BASE, ROM_SysCtlClockGet(),
DEFAULT_BIT_RATE, DEFAULT_UART_CONFIG);
ROM_UARTFIFOLevelSet(USB_UART_BASE, UART_FIFO_TX4_8, UART_FIFO_RX4_8);
//
// Configure and enable UART interrupts.
//
ROM_UARTIntClear(USB_UART_BASE, ROM_UARTIntStatus(USB_UART_BASE, false));
ROM_UARTIntEnable(USB_UART_BASE, (UART_INT_OE | UART_INT_BE | UART_INT_PE |
UART_INT_FE | UART_INT_RT | UART_INT_TX | UART_INT_RX));
//
// Enable the system tick.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Tell the user what we are up to.
//
DisplayStatus(&g_sContext, " Configuring... ");
//
// Initialize the transmit and receive buffers.
//
USBBufferInit(&g_sTxBuffer);
USBBufferInit(&g_sRxBuffer);
//
// Set the USB stack mode to Device mode with VBUS monitoring.
//
USBStackModeSet(0, eUSBModeDevice, 0);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDCDCInit(0, &g_sCDCDevice);
//
// Wait for initial configuration to complete.
//
DisplayStatus(&g_sContext, "Waiting for host");
//
// Clear our local byte counters.
//
ui32RxCount = 0;
ui32TxCount = 0;
//
// Enable interrupts now that the application is ready to start.
//
ROM_IntEnable(USB_UART_INT);
//
// Main application loop.
//
while(1)
{
//
// Have we been asked to update the status display?
//
if(g_ui32Flags & COMMAND_STATUS_UPDATE)
{
//
// Clear the command flag
//
ROM_IntMasterDisable();
g_ui32Flags &= ~COMMAND_STATUS_UPDATE;
ROM_IntMasterEnable();
DisplayStatus(&g_sContext, g_pcStatus);
}
//
// Has there been any transmit traffic since we last checked?
//
if(ui32TxCount != g_ui32UARTTxCount)
{
//
// Take a snapshot of the latest transmit count.
//
ui32TxCount = g_ui32UARTTxCount;
//
// Update the display of bytes transmitted by the UART.
//
usnprintf(pcBuffer, 16, "%d ", ui32TxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 40, 12, true);
//
// Update the RX buffer fullness. Remember that the buffers are
// named relative to the USB whereas the status display is from
// the UART's perspective. The USB's receive buffer is the UART's
// transmit buffer.
//
ui32Fullness = ((USBBufferDataAvailable(&g_sRxBuffer) * 100) /
UART_BUFFER_SIZE);
UpdateBufferMeter(&g_sContext, ui32Fullness, 40, 22);
}
//
// Has there been any receive traffic since we last checked?
//
if(ui32RxCount != g_ui32UARTRxCount)
{
//
// Take a snapshot of the latest receive count.
//
ui32RxCount = g_ui32UARTRxCount;
//
// Update the display of bytes received by the UART.
//
usnprintf(pcBuffer, 16, "%d ", ui32RxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 40, 32, true);
//
// Update the TX buffer fullness. Remember that the buffers are
// named relative to the USB whereas the status display is from
// the UART's perspective. The USB's transmit buffer is the UART's
// receive buffer.
//
ui32Fullness = ((USBBufferDataAvailable(&g_sTxBuffer) * 100) /
UART_BUFFER_SIZE);
UpdateBufferMeter(&g_sContext, ui32Fullness, 40, 42);
}
}
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
uint32_t ui32TxCount, ui32RxCount, ui32Fullness, ui32SysClock, ui32PLLRate;
tRectangle sRect;
char pcBuffer[16];
#ifdef USE_ULPI
uint32_t ui32Setting;
#endif
//
// Set the system clock to run at 120MHz from the PLL.
//
ui32SysClock = MAP_SysCtlClockFreqSet((SYSCTL_XTAL_25MHZ |
SYSCTL_OSC_MAIN | SYSCTL_USE_PLL |
SYSCTL_CFG_VCO_480), 120000000);
//
// Configure the device pins.
//
PinoutSet();
#ifdef USE_ULPI
//
// Switch the USB ULPI Pins over.
//
USBULPIPinoutSet();
//
// Enable USB ULPI with high speed support.
//
ui32Setting = USBLIB_FEATURE_ULPI_HS;
USBOTGFeatureSet(0, USBLIB_FEATURE_USBULPI, &ui32Setting);
//
// Setting the PLL frequency to zero tells the USB library to use the
// external USB clock.
//
ui32PLLRate = 0;
#else
//
// Save the PLL rate used by this application.
//
ui32PLLRate = 480000000;
#endif
//
// Enable the system tick.
//
ROM_SysTickPeriodSet(ui32SysClock / TICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Not configured initially.
//
g_ui32Flags = 0;
//
// Initialize the display driver.
//
Kentec320x240x16_SSD2119Init(ui32SysClock);
//
// Initialize the graphics context.
//
GrContextInit(&g_sContext, &g_sKentec320x240x16_SSD2119);
//
// Draw the application frame.
//
FrameDraw(&g_sContext, "usb-dev-serial");
//
// Fill the top 15 rows of the screen with blue to create the banner.
//
sRect.i16XMin = 0;
sRect.i16YMin = 0;
sRect.i16XMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.i16YMax = 23;
GrContextForegroundSet(&g_sContext, ClrDarkBlue);
GrRectFill(&g_sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&g_sContext, ClrWhite);
GrRectDraw(&g_sContext, &sRect);
//
// Show the various static text elements on the color STN display.
//
GrContextFontSet(&g_sContext, TEXT_FONT);
GrStringDraw(&g_sContext, "Tx bytes:", -1, 8, 80, false);
GrStringDraw(&g_sContext, "Tx buffer:", -1, 8, 105, false);
GrStringDraw(&g_sContext, "Rx bytes:", -1, 8, 160, false);
GrStringDraw(&g_sContext, "Rx buffer:", -1, 8, 185, false);
DrawBufferMeter(&g_sContext, 150, 105);
DrawBufferMeter(&g_sContext, 150, 185);
//
// Enable the UART that we will be redirecting.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
//
// Change the UART clock to the 16 MHz PIOSC.
//
UARTClockSourceSet(UART0_BASE, UART_CLOCK_PIOSC);
//
// Set the default UART configuration.
//
ROM_UARTConfigSetExpClk(UART0_BASE, UART_CLOCK,
DEFAULT_BIT_RATE, DEFAULT_UART_CONFIG);
ROM_UARTFIFOLevelSet(UART0_BASE, UART_FIFO_TX4_8, UART_FIFO_RX4_8);
//
// Configure and enable UART interrupts.
//
ROM_UARTIntClear(UART0_BASE, ROM_UARTIntStatus(UART0_BASE, false));
ROM_UARTIntEnable(UART0_BASE, (UART_INT_OE | UART_INT_BE | UART_INT_PE |
UART_INT_FE | UART_INT_RT | UART_INT_TX | UART_INT_RX));
//
// Tell the user what we are up to.
//
DisplayStatus(&g_sContext, " Configuring USB... ");
//
// Initialize the transmit and receive buffers.
//
USBBufferInit(&g_sTxBuffer);
USBBufferInit(&g_sRxBuffer);
//
// Set the USB stack mode to Device mode with VBUS monitoring.
//
USBStackModeSet(0, eUSBModeDevice, 0);
//
// Tell the USB library the CPU clock and the PLL frequency. This is a
// new requirement for TM4C129 devices.
//
USBDCDFeatureSet(0, USBLIB_FEATURE_CPUCLK, &ui32SysClock);
USBDCDFeatureSet(0, USBLIB_FEATURE_USBPLL, &ui32PLLRate);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDCDCInit(0, (tUSBDCDCDevice *)&g_sCDCDevice);
//
// Wait for initial configuration to complete.
//
DisplayStatus(&g_sContext, " Waiting for host... ");
//
// Clear our local byte counters.
//
ui32RxCount = 0;
ui32TxCount = 0;
g_ui32UARTTxCount = 0;
g_ui32UARTRxCount = 0;
#ifdef DEBUG
g_ui32UARTRxErrors = 0;
#endif
//
// Enable interrupts now that the application is ready to start.
//
ROM_IntEnable(INT_UART0);
//
// Main application loop.
//
while(1)
{
//
// Have we been asked to update the status display?
//
if(HWREGBITW(&g_ui32Flags, FLAG_STATUS_UPDATE))
{
//
// Clear the command flag
//
HWREGBITW(&g_ui32Flags, FLAG_STATUS_UPDATE) = 0;
DisplayStatus(&g_sContext, g_pcStatus);
}
//
// Has there been any transmit traffic since we last checked?
//
if(ui32TxCount != g_ui32UARTTxCount)
{
//
// Take a snapshot of the latest transmit count.
//
ui32TxCount = g_ui32UARTTxCount;
//
// Update the display of bytes transmitted by the UART.
//
usnprintf(pcBuffer, 16, "%d ", ui32TxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 150, 80, true);
//
// Update the RX buffer fullness. Remember that the buffers are
// named relative to the USB whereas the status display is from
// the UART's perspective. The USB's receive buffer is the UART's
// transmit buffer.
//
ui32Fullness = ((USBBufferDataAvailable(&g_sRxBuffer) * 100) /
UART_BUFFER_SIZE);
UpdateBufferMeter(&g_sContext, ui32Fullness, 150, 105);
}
//
// Has there been any receive traffic since we last checked?
//
if(ui32RxCount != g_ui32UARTRxCount)
{
//
// Take a snapshot of the latest receive count.
//
ui32RxCount = g_ui32UARTRxCount;
//
// Update the display of bytes received by the UART.
//
usnprintf(pcBuffer, 16, "%d ", ui32RxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 150, 160, true);
//
// Update the TX buffer fullness. Remember that the buffers are
// named relative to the USB whereas the status display is from
// the UART's perspective. The USB's transmit buffer is the UART's
// receive buffer.
//
ui32Fullness = ((USBBufferDataAvailable(&g_sTxBuffer) * 100) /
UART_BUFFER_SIZE);
UpdateBufferMeter(&g_sContext, ui32Fullness, 150, 185);
}
}
}
//*****************************************************************************
//
// Main application entry function.
//
//*****************************************************************************
int
main(void)
{
tBoolean bRetcode;
//
// Set the system clock to run at 50MHz from the PLL
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// NB: We don't call PinoutSet() in this testcase since the EM header
// expansion board doesn't currently have an I2C ID EEPROM. If we did
// call PinoutSet() this would configure all the EPI pins for SDRAM and
// we don't want to do this.
//
g_eDaughterType = DAUGHTER_NONE;
//
// Enable peripherals required to drive the LCD.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOH);
//
// Configure SysTick for a 10Hz interrupt.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / TICKS_PER_SECOND);
ROM_SysTickEnable();
ROM_SysTickIntEnable();
//
// Initialize the display driver.
//
Kitronix320x240x16_SSD2119Init();
//
// Initialize the touch screen driver.
//
TouchScreenInit();
//
// Set the touch screen event handler.
//
TouchScreenCallbackSet(WidgetPointerMessage);
//
// Add the compile-time defined widgets to the widget tree.
//
WidgetAdd(WIDGET_ROOT, (tWidget *)&g_sHeading);
//
// Initialize the status string.
//
UpdateStatus(true, "Monitoring...");
//
// Paint the widget tree to make sure they all appear on the display.
//
WidgetPaint(WIDGET_ROOT);
//
// Initialize the SimpliciTI BSP.
//
BSP_Init();
//
// Set the SimpliciTI device address using the current Ethernet MAC address
// to ensure something like uniqueness.
//
bRetcode = SetSimpliciTIAddress();
//
// Did we have a problem with the address?
//
if(!bRetcode)
{
//
// Yes - make sure the display is updated then hang the app.
//
WidgetMessageQueueProcess();
while(1)
{
//
// MAC address is not set so hang the app.
//
}
}
//
// Initialize the SimpliciTI stack but don't set any receive callback.
//
SMPL_Init(0);
//
// Start monitoring for alert messages from other devices. This function
// doesn't return.
//
MonitorForBadNews();
}
//*****************************************************************************
//
// Main application entry function.
//
//*****************************************************************************
int
main(void)
{
tBoolean bRetcode;
smplStatus_t eRetcode;
ioctlScanChan_t sScan;
freqEntry_t pFreq[NWK_FREQ_TBL_SIZE];
tBoolean bFirstTimeThrough;
unsigned long ulLoop;
uint8_t ucLast;
//
// Set the system clock to run at 50MHz from the PLL
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// NB: We don't call PinoutSet() in this testcase since the EM header
// expansion board doesn't currently have an I2C ID EEPROM. If we did
// call PinoutSet() this would configure all the EPI pins for SDRAM and
// we don't want to do this.
//
g_eDaughterType = DAUGHTER_NONE;
//
// Enable peripherals required to drive the LCD.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOH);
//
// Configure SysTick for a 10Hz interrupt.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / TICKS_PER_SECOND);
ROM_SysTickEnable();
ROM_SysTickIntEnable();
//
// Initialize the display driver.
//
Kitronix320x240x16_SSD2119Init();
//
// Initialize the touch screen driver.
//
TouchScreenInit();
//
// Set the touch screen event handler.
//
TouchScreenCallbackSet(WidgetPointerMessage);
//
// Add the compile-time defined widgets to the widget tree.
//
WidgetAdd(WIDGET_ROOT, (tWidget *)&g_sHeading);
//
// Initialize the status string.
//
UpdateStatus("Initializing...");
//
// Paint the widget tree to make sure they all appear on the display.
//
WidgetPaint(WIDGET_ROOT);
//
// Initialize the SimpliciTI BSP.
//
BSP_Init();
//
// Set the SimpliciTI device address using the current Ethernet MAC address
// to ensure something like uniqueness.
//
bRetcode = SetSimpliciTIAddress();
//
// Did we have a problem with the address?
//
if(!bRetcode)
{
//
// Yes - make sure the display is updated then hang the app.
//
WidgetMessageQueueProcess();
while(1)
{
//
// MAC address is not set so hang the app.
//
}
}
//
// Turn on both our LEDs
//
SetLED(1, true);
SetLED(2, true);
UpdateStatus("Joining network...");
//
// Initialize the SimpliciTI stack but don't set any receive callback.
//
while(1)
{
eRetcode = SMPL_Init((uint8_t (*)(linkID_t))0);
if(eRetcode == SMPL_SUCCESS)
{
break;
}
ToggleLED(1);
ToggleLED(2);
SPIN_ABOUT_A_SECOND;
}
//
// Tell the user what's up.
//
UpdateStatus("Sniffing...");
//
// Set up for our first sniff.
//
sScan.freq = pFreq;
bFirstTimeThrough = true;
ucLast = 0xFF;
//
// Keep sniffing forever.
//
while (1)
{
//
// Wait a while.
//
SPIN_ABOUT_A_QUARTER_SECOND;
//
// Scan for the active channel.
//
SMPL_Ioctl(IOCTL_OBJ_FREQ, IOCTL_ACT_SCAN, &sScan);
//
// Did we find a signal?
//
if (1 == sScan.numChan)
{
if (bFirstTimeThrough)
{
//
// Set the initial LED state.
//
SetLED(1, false);
SetLED(2, true);
//
// Wait a while.
//
for(ulLoop = 0; ulLoop < 15; ulLoop--)
{
//
// Toggle both LEDs and wait a bit.
//
ToggleLED(1);
ToggleLED(2);
SPIN_ABOUT_A_QUARTER_SECOND;
}
bFirstTimeThrough = false;
}
//
// Has the channel changed since the last time we updated the
// display?
//
if(pFreq[0].logicalChan != ucLast)
{
//
// Remember the channel we just detected.
//
ucLast = pFreq[0].logicalChan;
//
// Tell the user which channel we found to be active.
//
UpdateStatus("Active channel is %d.", pFreq[0].logicalChan);
//
// Set the "LEDs" to mimic the behavior of the MSP430 versions
// of this application.
//
switch(pFreq[0].logicalChan)
{
case 0:
{
/* GREEN OFF */
/* RED OFF */
SetLED(1, false);
SetLED(2, false);
break;
}
case 1:
{
/* GREEN OFF */
/* RED ON */
SetLED(1, false);
SetLED(2, true);
break;
}
case 2:
{
/* GREEN ON */
/* RED OFF */
SetLED(1, true);
SetLED(2, false);
break;
}
case 3:
{
/* GREEN ON */
/* RED ON */
SetLED(1, true);
SetLED(2, true);
break;
}
case 4:
{
/* blink them both... */
SetLED(1, false);
SetLED(2, false);
SPIN_ABOUT_A_QUARTER_SECOND;
SetLED(1, true);
SetLED(2, true);
SPIN_ABOUT_A_QUARTER_SECOND;
SetLED(1, false);
SetLED(2, false);
}
}
}
}
}
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
unsigned long ulTxCount;
unsigned long ulRxCount;
//
// Set the clocking to run from the PLL at 50MHz
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Enable the UART.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
GPIOPinConfigure(GPIO_PA0_U0RX);
GPIOPinConfigure(GPIO_PA1_U0TX);
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
UARTStdioInit(0);
UARTprintf("\033[2JBulk device application\n");
//
// Not configured initially.
//
g_bUSBConfigured = false;
//
// Enable the system tick.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Initialize the transmit and receive buffers.
//
USBBufferInit(&g_sTxBuffer);
USBBufferInit(&g_sRxBuffer);
//
// Set the USB stack mode to Device mode with VBUS monitoring.
//
USBStackModeSet(0, USB_MODE_DEVICE, 0);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDBulkInit(0, &g_sBulkDevice);
//
// Wait for initial configuration to complete.
//
UARTprintf("Waiting for host...\n");
//
// Clear our local byte counters.
//
ulRxCount = 0;
ulTxCount = 0;
//
// Main application loop.
//
while(1)
{
//
// See if any data has been transferred.
//
if((ulTxCount != g_ulTxCount) || (ulRxCount != g_ulRxCount))
{
//
// Take a snapshot of the latest transmit and receive counts.
//
ulTxCount = g_ulTxCount;
ulRxCount = g_ulRxCount;
//
// Update the display of bytes transferred.
//
UARTprintf("\rTx: %d Rx: %d", ulTxCount, ulRxCount);
}
}
}
//*****************************************************************************
//
// This is the main loop that runs the application.
//
//*****************************************************************************
int
main(void)
{
tRectangle sRect;
uint_fast32_t ui32Retcode;
//
// Set the system clock to run at 50MHz from the PLL.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Configure SysTick for a 100Hz interrupt. The FatFs driver wants a 10 ms
// tick.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / 100);
ROM_SysTickEnable();
ROM_SysTickIntEnable();
//
// Configure and enable uDMA
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UDMA);
SysCtlDelay(10);
ROM_uDMAControlBaseSet(&sDMAControlTable[0]);
ROM_uDMAEnable();
//
// Initialize the display driver.
//
CFAL96x64x16Init();
//
// Initialize the graphics context.
//
GrContextInit(&g_sContext, &g_sCFAL96x64x16);
//
// Fill the top 15 rows of the screen with blue to create the banner.
//
sRect.i16XMin = 0;
sRect.i16YMin = 0;
sRect.i16XMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.i16YMax = DISPLAY_BANNER_HEIGHT - 1;
GrContextForegroundSet(&g_sContext, ClrDarkBlue);
GrRectFill(&g_sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&g_sContext, ClrWhite);
GrRectDraw(&g_sContext, &sRect);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, g_psFontFixed6x8);
GrStringDrawCentered(&g_sContext, "usb-dev-msc", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 5, 0);
//
// Initialize the idle timeout and reset all flags.
//
g_ui32IdleTimeout = 0;
g_ui32Flags = 0;
//
// Initialize the state to idle.
//
g_eMSCState = MSC_DEV_DISCONNECTED;
//
// Draw the status bar and set it to idle.
//
UpdateStatus("Disconnected", 1);
//
// Enable the USB controller.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_USB0);
//
// Set the USB pins to be controlled by the USB controller.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOG);
ROM_GPIOPinConfigure(GPIO_PG4_USB0EPEN);
ROM_GPIOPinTypeUSBDigital(GPIO_PORTG_BASE, GPIO_PIN_4);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOL);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTL_BASE, GPIO_PIN_6 | GPIO_PIN_7);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTB_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// Set the USB stack mode to Device mode with VBUS monitoring.
//
USBStackModeSet(0, eUSBModeDevice, 0);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDMSCInit(0, &g_sMSCDevice);
//
// Determine whether or not an SDCard is installed. If not, print a
// warning and have the user install one and restart.
//
ui32Retcode = disk_initialize(0);
GrContextFontSet(&g_sContext, g_psFontFixed6x8);
if(ui32Retcode != RES_OK) {
GrStringDrawCentered(&g_sContext, "No SDCard Found", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 16, 0);
GrStringDrawCentered(&g_sContext, "Please insert",
-1, GrContextDpyWidthGet(&g_sContext) / 2, 26, 0);
GrStringDrawCentered(&g_sContext, "a card and",
-1, GrContextDpyWidthGet(&g_sContext) / 2, 36, 0);
GrStringDrawCentered(&g_sContext, "reset the board.",
-1, GrContextDpyWidthGet(&g_sContext) / 2, 46, 0);
} else {
GrStringDrawCentered(&g_sContext, "SDCard Found", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 30, 0);
}
//
// Drop into the main loop.
//
while(1) {
switch(g_eMSCState) {
case MSC_DEV_READ: {
//
// Update the screen if necessary.
//
if(g_ui32Flags & FLAG_UPDATE_STATUS) {
UpdateStatus("Reading", 0);
g_ui32Flags &= ~FLAG_UPDATE_STATUS;
}
//
// If there is no activity then return to the idle state.
//
if(g_ui32IdleTimeout == 0) {
UpdateStatus("Idle", 0);
g_eMSCState = MSC_DEV_IDLE;
}
break;
}
case MSC_DEV_WRITE: {
//
// Update the screen if necessary.
//
if(g_ui32Flags & FLAG_UPDATE_STATUS) {
UpdateStatus("Writing", 0);
g_ui32Flags &= ~FLAG_UPDATE_STATUS;
}
//
// If there is no activity then return to the idle state.
//
if(g_ui32IdleTimeout == 0) {
UpdateStatus("Idle", 0);
g_eMSCState = MSC_DEV_IDLE;
}
break;
}
case MSC_DEV_DISCONNECTED: {
//
// Update the screen if necessary.
//
if(g_ui32Flags & FLAG_UPDATE_STATUS) {
UpdateStatus("Disconnected", 0);
g_ui32Flags &= ~FLAG_UPDATE_STATUS;
}
break;
}
case MSC_DEV_IDLE: {
break;
}
default: {
break;
}
}
}
}
//*****************************************************************************
//
// This is the main example program. It checks to see that the interrupts are
// processed in the correct order when they have identical priorities,
// increasing priorities, and decreasing priorities. This exercises interrupt
// preemption and tail chaining.
//
//*****************************************************************************
int
main(void)
{
unsigned long ulError;
//
// Set the clocking to run directly from the crystal.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Enable the peripherals used by this example.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
//
// Initialize the UART.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
GPIOPinConfigure(GPIO_PA0_U0RX);
GPIOPinConfigure(GPIO_PA1_U0TX);
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
UARTStdioInit(0);
UARTprintf("\033[2JInterrupts\n");
//
// Configure the F0, D1 and D2 to be outputs to indicate entry/exit of one
// of the interrupt handlers.
//
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTB_BASE,
GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2);
ROM_GPIOPinWrite(GPIO_PORTB_BASE, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2, 0);
//
// Set up and enable the SysTick timer. It will be used as a reference
// for delay loops in the interrupt handlers. The SysTick timer period
// will be set up for one second.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet());
ROM_SysTickEnable();
//
// Reset the error indicator.
//
ulError = 0;
//
// Enable interrupts to the processor.
//
ROM_IntMasterEnable();
//
// Enable the interrupts.
//
ROM_IntEnable(INT_GPIOA);
ROM_IntEnable(INT_GPIOB);
ROM_IntEnable(INT_GPIOC);
//
// Indicate that the equal interrupt priority test is beginning.
//
UARTprintf("\nEqual Priority\n");
//
// Set the interrupt priorities so they are all equal.
//
ROM_IntPrioritySet(INT_GPIOA, 0x00);
ROM_IntPrioritySet(INT_GPIOB, 0x00);
ROM_IntPrioritySet(INT_GPIOC, 0x00);
//
// Reset the interrupt flags.
//
g_ulGPIOa = 0;
g_ulGPIOb = 0;
g_ulGPIOc = 0;
g_ulIndex = 1;
//
// Trigger the interrupt for GPIO C.
//
HWREG(NVIC_SW_TRIG) = INT_GPIOC - 16;
//
// Put the current interrupt state on the LCD.
//
DisplayIntStatus();
//
// Verify that the interrupts were processed in the correct order.
//
if((g_ulGPIOa != 3) || (g_ulGPIOb != 2) || (g_ulGPIOc != 1))
{
ulError |= 1;
}
//
// Wait two seconds.
//
Delay(2);
//
// Indicate that the decreasing interrupt priority test is beginning.
//
UARTprintf("\nDecreasing Priority\n");
//
// Set the interrupt priorities so that they are decreasing (i.e. C > B >
// A).
//
ROM_IntPrioritySet(INT_GPIOA, 0x80);
ROM_IntPrioritySet(INT_GPIOB, 0x40);
ROM_IntPrioritySet(INT_GPIOC, 0x00);
//
// Reset the interrupt flags.
//
g_ulGPIOa = 0;
g_ulGPIOb = 0;
g_ulGPIOc = 0;
g_ulIndex = 1;
//
// Trigger the interrupt for GPIO C.
//
HWREG(NVIC_SW_TRIG) = INT_GPIOC - 16;
//
// Put the current interrupt state on the UART.
//
DisplayIntStatus();
//
// Verify that the interrupts were processed in the correct order.
//
if((g_ulGPIOa != 3) || (g_ulGPIOb != 2) || (g_ulGPIOc != 1))
{
ulError |= 2;
}
//
// Wait two seconds.
//
Delay(2);
//
// Indicate that the increasing interrupt priority test is beginning.
//
UARTprintf("\nIncreasing Priority\n");
//
// Set the interrupt priorities so that they are increasing (i.e. C < B <
// A).
//
ROM_IntPrioritySet(INT_GPIOA, 0x00);
ROM_IntPrioritySet(INT_GPIOB, 0x40);
ROM_IntPrioritySet(INT_GPIOC, 0x80);
//
// Reset the interrupt flags.
//
g_ulGPIOa = 0;
g_ulGPIOb = 0;
g_ulGPIOc = 0;
g_ulIndex = 1;
//
// Trigger the interrupt for GPIO C.
//
HWREG(NVIC_SW_TRIG) = INT_GPIOC - 16;
//
// Put the current interrupt state on the UART.
//
DisplayIntStatus();
//
// Verify that the interrupts were processed in the correct order.
//
if((g_ulGPIOa != 1) || (g_ulGPIOb != 2) || (g_ulGPIOc != 3))
{
ulError |= 4;
}
//
// Wait two seconds.
//
Delay(2);
//
// Disable the interrupts.
//
ROM_IntDisable(INT_GPIOA);
ROM_IntDisable(INT_GPIOB);
ROM_IntDisable(INT_GPIOC);
//
// Disable interrupts to the processor.
//
ROM_IntMasterDisable();
//
// Print out the test results.
//
UARTprintf("\nInterrupt Priority =: %s >: %s <: %s\n",
(ulError & 1) ? "Fail" : "Pass",
(ulError & 2) ? "Fail" : "Pass",
(ulError & 4) ? "Fail" : "Pass");
//
// Finished.
//
while(1)
{
}
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
volatile uint32_t ui32Loop;
uint32_t ui32TxCount;
uint32_t ui32RxCount;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run from the PLL at 50MHz
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Enable the GPIO port that is used for the on-board LED.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
//
// Enable the GPIO pins for the LED (PF2 & PF3).
//
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_3 | GPIO_PIN_2);
//
// Open UART0 and show the application name on the UART.
//
ConfigureUART();
UARTprintf("\033[2JTiva C Series USB bulk device example\n");
UARTprintf("---------------------------------\n\n");
//
// Not configured initially.
//
g_bUSBConfigured = false;
//
// Enable the GPIO peripheral used for USB, and configure the USB
// pins.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTD_BASE, GPIO_PIN_4 | GPIO_PIN_5);
//
// Enable the system tick.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Tell the user what we are up to.
//
UARTprintf("Configuring USB\n");
//
// Initialize the transmit and receive buffers.
//
USBBufferInit(&g_sTxBuffer);
USBBufferInit(&g_sRxBuffer);
//
// Set the USB stack mode to Device mode with VBUS monitoring.
//
USBStackModeSet(0, eUSBModeForceDevice, 0);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDBulkInit(0, &g_sBulkDevice);
//
// Wait for initial configuration to complete.
//
UARTprintf("Waiting for host...\n");
//
// Clear our local byte counters.
//
ui32RxCount = 0;
ui32TxCount = 0;
//
// Main application loop.
//
while(1)
{
//
// See if any data has been transferred.
//
if((ui32TxCount != g_ui32TxCount) || (ui32RxCount != g_ui32RxCount))
{
//
// Has there been any transmit traffic since we last checked?
//
if(ui32TxCount != g_ui32TxCount)
{
//
// Turn on the Green LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, GPIO_PIN_3);
//
// Delay for a bit.
//
for(ui32Loop = 0; ui32Loop < 150000; ui32Loop++)
{
}
//
// Turn off the Green LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, 0);
//
// Take a snapshot of the latest transmit count.
//
ui32TxCount = g_ui32TxCount;
}
//
// Has there been any receive traffic since we last checked?
//
if(ui32RxCount != g_ui32RxCount)
{
//
// Turn on the Blue LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, GPIO_PIN_2);
//
// Delay for a bit.
//
for(ui32Loop = 0; ui32Loop < 150000; ui32Loop++)
{
}
//
// Turn off the Blue LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, 0);
//
// Take a snapshot of the latest receive count.
//
ui32RxCount = g_ui32RxCount;
}
//
// Update the display of bytes transferred.
//
UARTprintf("\rTx: %d Rx: %d", ui32TxCount, ui32RxCount);
}
}
}
//*****************************************************************************
//
// The program main function. It performs initialization, then runs a loop to
// process USB activities and operate the user interface.
//
//*****************************************************************************
int
main(void)
{
uint32_t ui32DriveTimeout;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the system clock to run at 50MHz from the PLL.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Configure the required pins for USB operation.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOG);
ROM_GPIOPinConfigure(GPIO_PG4_USB0EPEN);
ROM_GPIOPinTypeUSBDigital(GPIO_PORTG_BASE, GPIO_PIN_4);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOL);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTL_BASE, GPIO_PIN_6 | GPIO_PIN_7);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTB_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// Configure SysTick for a 100Hz interrupt.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / TICKS_PER_SECOND);
ROM_SysTickEnable();
ROM_SysTickIntEnable();
//
// Enable the uDMA controller and set up the control table base.
// The uDMA controller is used by the USB library.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UDMA);
ROM_uDMAEnable();
ROM_uDMAControlBaseSet(g_psDMAControlTable);
//
// Enable Interrupts
//
ROM_IntMasterEnable();
//
// Initialize the display driver.
//
CFAL96x64x16Init();
//
// Initialize the buttons driver.
//
ButtonsInit();
//
// Initialize two offscreen displays and assign the palette. These
// buffers are used by the slide menu widget to allow animation effects.
//
GrOffScreen4BPPInit(&g_sOffscreenDisplayA, g_pui8OffscreenBufA, 96, 64);
GrOffScreen4BPPPaletteSet(&g_sOffscreenDisplayA, g_pui32Palette, 0,
NUM_PALETTE_ENTRIES);
GrOffScreen4BPPInit(&g_sOffscreenDisplayB, g_pui8OffscreenBufB, 96, 64);
GrOffScreen4BPPPaletteSet(&g_sOffscreenDisplayB, g_pui32Palette, 0,
NUM_PALETTE_ENTRIES);
//
// Show an initial status screen
//
g_pcStatusLines[0] = "Waiting";
g_pcStatusLines[1] = "for device";
ShowStatusScreen(g_pcStatusLines, 2);
//
// Add the compile-time defined widgets to the widget tree.
//
WidgetAdd(WIDGET_ROOT, (tWidget *)&g_sFileMenuWidget);
//
// Initially wait for device connection.
//
g_eState = STATE_NO_DEVICE;
//
// Initialize the USB stack for host mode.
//
USBStackModeSet(0, eUSBModeHost, 0);
//
// Register the host class drivers.
//
USBHCDRegisterDrivers(0, g_ppHostClassDrivers, g_ui32NumHostClassDrivers);
//
// Open an instance of the mass storage class driver.
//
g_psMSCInstance = USBHMSCDriveOpen(0, MSCCallback);
//
// Initialize the drive timeout.
//
ui32DriveTimeout = USBMSC_DRIVE_RETRY;
//
// Initialize the power configuration. This sets the power enable signal
// to be active high and does not enable the power fault.
//
USBHCDPowerConfigInit(0, USBHCD_VBUS_AUTO_HIGH | USBHCD_VBUS_FILTER);
//
// Initialize the USB controller for host operation.
//
USBHCDInit(0, g_pui8HCDPool, HCD_MEMORY_SIZE);
//
// Initialize the file system.
//
FileInit();
//
// Enter an infinite loop to run the user interface and process USB
// events.
//
while(1)
{
uint32_t ui32LastTickCount = 0;
//
// Call the USB stack to keep it running.
//
USBHCDMain();
//
// Process any messages in the widget message queue. This keeps the
// display UI running.
//
WidgetMessageQueueProcess();
//
// Take action based on the application state.
//
switch(g_eState)
{
//
// A device has enumerated.
//
case STATE_DEVICE_ENUM:
{
//
// Check to see if the device is ready. If not then stay
// in this state and we will check it again on the next pass.
//
if(USBHMSCDriveReady(g_psMSCInstance) != 0)
{
//
// Wait about 500ms before attempting to check if the
// device is ready again.
//
ROM_SysCtlDelay(ROM_SysCtlClockGet()/(3));
//
// Decrement the retry count.
//
ui32DriveTimeout--;
//
// If the timeout is hit then go to the
// STATE_TIMEOUT_DEVICE state.
//
if(ui32DriveTimeout == 0)
{
g_eState = STATE_TIMEOUT_DEVICE;
}
break;
}
//
// Getting here means the device is ready.
// Reset the CWD to the root directory.
//
g_pcCwdBuf[0] = '/';
g_pcCwdBuf[1] = 0;
//
// Set the initial directory level to the root
//
g_ui32Level = 0;
//
// We need to reset the indexes of the root menu to 0, so that
// it will start at the top of the file list, and reset the
// slide menu widget to start with the root menu.
//
g_psFileMenus[g_ui32Level].ui32CenterIndex = 0;
g_psFileMenus[g_ui32Level].ui32FocusIndex = 0;
SlideMenuMenuSet(&g_sFileMenuWidget, &g_psFileMenus[g_ui32Level]);
//
// Initiate a directory change to the root. This will
// populate a menu structure representing the root directory.
//
if(ProcessDirChange("/", g_ui32Level))
{
//
// If there were no errors reported, we are ready for
// MSC operation.
//
g_eState = STATE_DEVICE_READY;
//
// Set the Device Present flag.
//
g_ui32Flags = FLAGS_DEVICE_PRESENT;
//
// Request a repaint so the file menu will be shown
//
WidgetPaint(WIDGET_ROOT);
}
break;
}
//
// If there is no device then just wait for one.
//
case STATE_NO_DEVICE:
{
if(g_ui32Flags == FLAGS_DEVICE_PRESENT)
{
//
// Show waiting message on screen
//
g_pcStatusLines[0] = "Waiting";
g_pcStatusLines[1] = "for device";
ShowStatusScreen(g_pcStatusLines, 2);
//
// Clear the Device Present flag.
//
g_ui32Flags &= ~FLAGS_DEVICE_PRESENT;
}
break;
}
//
// An unknown device was connected.
//
case STATE_UNKNOWN_DEVICE:
{
//
// If this is a new device then change the status.
//
if((g_ui32Flags & FLAGS_DEVICE_PRESENT) == 0)
{
//
// Clear the screen and indicate that an unknown device
// is present.
//
g_pcStatusLines[0] = "Unknown";
g_pcStatusLines[1] = "device";
ShowStatusScreen(g_pcStatusLines, 2);
}
//
// Set the Device Present flag.
//
g_ui32Flags = FLAGS_DEVICE_PRESENT;
break;
}
//
// The connected mass storage device is not reporting ready.
//
case STATE_TIMEOUT_DEVICE:
{
//
// If this is the first time in this state then print a
// message.
//
if((g_ui32Flags & FLAGS_DEVICE_PRESENT) == 0)
{
//
//
// Clear the screen and indicate that an unknown device
// is present.
//
g_pcStatusLines[0] = "Device";
g_pcStatusLines[1] = "Timeout";
ShowStatusScreen(g_pcStatusLines, 2);
}
//
// Set the Device Present flag.
//
g_ui32Flags = FLAGS_DEVICE_PRESENT;
break;
}
//
// The device is ready and in use.
//
case STATE_DEVICE_READY:
{
//
// Process occurrence of timer tick. Check for user input
// once each tick.
//
if(g_ui32SysTickCount != ui32LastTickCount)
{
uint8_t ui8ButtonState;
uint8_t ui8ButtonChanged;
ui32LastTickCount = g_ui32SysTickCount;
//
// Get the current debounced state of the buttons.
//
ui8ButtonState = ButtonsPoll(&ui8ButtonChanged, 0);
//
// If select button or right button is pressed, then we
// are trying to descend into another directory
//
if(BUTTON_PRESSED(SELECT_BUTTON,
ui8ButtonState, ui8ButtonChanged) ||
BUTTON_PRESSED(RIGHT_BUTTON,
ui8ButtonState, ui8ButtonChanged))
{
uint32_t ui32NewLevel;
uint32_t ui32ItemIdx;
char *pcItemName;
//
// Get a pointer to the current menu for this CWD.
//
tSlideMenu *psMenu = &g_psFileMenus[g_ui32Level];
//
// Get the highlighted index in the current file list.
// This is the currently highlighted file or dir
// on the display. Then get the name of the file at
// this index.
//
ui32ItemIdx = SlideMenuFocusItemGet(psMenu);
pcItemName = psMenu->psSlideMenuItems[ui32ItemIdx].pcText;
//
// Make sure we are not yet past the maximum tree
// depth.
//
if(g_ui32Level < MAX_SUBDIR_DEPTH)
{
//
// Potential new level is one greater than the
// current level.
//
ui32NewLevel = g_ui32Level + 1;
//
// Process the directory change to the new
// directory. This function will populate a menu
// structure with the files and subdirs in the new
// directory.
//
if(ProcessDirChange(pcItemName, ui32NewLevel))
{
//
// If the change was successful, then update
// the level.
//
g_ui32Level = ui32NewLevel;
//
// Now that all the prep is done, send the
// KEY_RIGHT message to the widget and it will
// "slide" from the previous file list to the
// new file list of the CWD.
//
SendWidgetKeyMessage(WIDGET_MSG_KEY_RIGHT);
}
}
}
//
// If the UP button is pressed, just pass it to the widget
// which will handle scrolling the list of files.
//
if(BUTTON_PRESSED(UP_BUTTON, ui8ButtonState, ui8ButtonChanged))
{
SendWidgetKeyMessage(WIDGET_MSG_KEY_UP);
}
//
// If the DOWN button is pressed, just pass it to the widget
// which will handle scrolling the list of files.
//
if(BUTTON_PRESSED(DOWN_BUTTON, ui8ButtonState, ui8ButtonChanged))
{
SendWidgetKeyMessage(WIDGET_MSG_KEY_DOWN);
}
//
// If the LEFT button is pressed, then we are attempting
// to go up a level in the file system.
//
if(BUTTON_PRESSED(LEFT_BUTTON, ui8ButtonState, ui8ButtonChanged))
{
uint32_t ui32NewLevel;
//
// Make sure we are not already at the top of the
// directory tree (at root).
//
if(g_ui32Level)
{
//
// Potential new level is one less than the
// current level.
//
ui32NewLevel = g_ui32Level - 1;
//
// Process the directory change to the new
// directory. This function will populate a menu
// structure with the files and subdirs in the new
// directory.
//
if(ProcessDirChange("..", ui32NewLevel))
{
//
// If the change was successful, then update
// the level.
//
g_ui32Level = ui32NewLevel;
//
// Now that all the prep is done, send the
// KEY_LEFT message to the widget and it will
// "slide" from the previous file list to the
// new file list of the CWD.
//
SendWidgetKeyMessage(WIDGET_MSG_KEY_LEFT);
}
}
}
}
break;
}
//
// Something has caused a power fault.
//
case STATE_POWER_FAULT:
{
//
// Clear the screen and show a power fault indication.
//
g_pcStatusLines[0] = "Power";
g_pcStatusLines[1] = "fault";
ShowStatusScreen(g_pcStatusLines, 2);
break;
}
default:
{
break;
}
}
}
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run from the PLL at 50MHz
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Enable the GPIO port that is used for the on-board LED.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
//
// Enable the GPIO pins for the LED (PF2 & PF3).
//
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_3 | GPIO_PIN_2 | GPIO_PIN_1);
//
// Open UART0 and show the application name on the UART.
//
ConfigureUART();
UARTprintf("\033[2JTiva C Series USB bulk device example\n");
UARTprintf("---------------------------------\n\n");
//
// Not configured initially.
//
g_bUSBConfigured = false;
//
// Enable the GPIO peripheral used for USB, and configure the USB
// pins.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTD_BASE, GPIO_PIN_4 | GPIO_PIN_5);
//
// Enable the system tick.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Tell the user what we are up to.
//
UARTprintf("Configuring USB\n");
//
// Initialize the transmit and receive buffers.
//
USBBufferInit(&g_sTxBuffer);
USBBufferInit(&g_sRxBuffer);
//
// Set the USB stack mode to Device mode with VBUS monitoring.
//
USBStackModeSet(0, eUSBModeForceDevice, 0);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
myBulk=USBDBulkInit(0, &g_sBulkDevice);
//
// Wait for initial configuration to complete.
//
UARTprintf("Waiting for host...\n");
//
// Clear our local byte counters.
//
while(!isUSB_ready);
adc_cofig();
//
// Main application loop.
//
while(1)
{
int readVal;
if(txReady){
adc_capture();
((int*)myOutBuffer)[0]=adc_getData();
readVal=((int*)myOutBuffer)[0];
UARTprintf("adc = %d\n",readVal);
txReady=0;
USBDBulkPacketWrite(myBulk,myOutBuffer,4,true);
}
}
}
//*****************************************************************************
//
// This is the main example program. It checks to see that the interrupts are
// processed in the correct order when they have identical priorities,
// increasing priorities, and decreasing priorities. This exercises interrupt
// preemption and tail chaining.
//
//*****************************************************************************
int
main(void)
{
tRectangle sRect;
uint_fast8_t ui8Error;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run directly from the crystal.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Enable the peripherals used by this example.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
//
// Initialize the display driver.
//
CFAL96x64x16Init();
//
// Initialize the graphics context and find the middle X coordinate.
//
GrContextInit(&g_sContext, &g_sCFAL96x64x16);
//
// Fill the top part of the screen with blue to create the banner.
//
sRect.i16XMin = 0;
sRect.i16YMin = 0;
sRect.i16XMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.i16YMax = 9;
GrContextForegroundSet(&g_sContext, ClrDarkBlue);
GrRectFill(&g_sContext, &sRect);
//
// Change foreground for white text.
//
GrContextForegroundSet(&g_sContext, ClrWhite);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, g_psFontFixed6x8);
GrStringDrawCentered(&g_sContext, "interrupts", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 4, 0);
GrContextFontSet(&g_sContext, g_psFontFixed6x8);
//
// Put the status header text on the display.
//
GrStringDraw(&g_sContext, "Active:", -1, 6, 32, 0);
GrStringDraw(&g_sContext, "Pending:", -1, 0, 44, 0);
//
// Configure the PB0-PB2 to be outputs to indicate entry/exit of one
// of the interrupt handlers.
//
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTD_BASE, GPIO_PIN_0 | GPIO_PIN_1 |
GPIO_PIN_3);
ROM_GPIOPinWrite(GPIO_PORTD_BASE, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2, 0);
//
// Set up and enable the SysTick timer. It will be used as a reference
// for delay loops in the interrupt handlers. The SysTick timer period
// will be set up for one second.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet());
ROM_SysTickEnable();
//
// Reset the error indicator.
//
ui8Error = 0;
//
// Enable interrupts to the processor.
//
ROM_IntMasterEnable();
//
// Enable the interrupts.
//
ROM_IntEnable(INT_GPIOA);
ROM_IntEnable(INT_GPIOB);
ROM_IntEnable(INT_GPIOC);
//
// Indicate that the equal interrupt priority test is beginning.
//
GrStringDrawCentered(&g_sContext, "Equal Pri", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 20, 1);
//
// Set the interrupt priorities so they are all equal.
//
ROM_IntPrioritySet(INT_GPIOA, 0x00);
ROM_IntPrioritySet(INT_GPIOB, 0x00);
ROM_IntPrioritySet(INT_GPIOC, 0x00);
//
// Reset the interrupt flags.
//
g_ui32GPIOa = 0;
g_ui32GPIOb = 0;
g_ui32GPIOc = 0;
g_ui32Index = 1;
//
// Trigger the interrupt for GPIO C.
//
HWREG(NVIC_SW_TRIG) = INT_GPIOC - 16;
//
// Put the current interrupt state on the LCD.
//
DisplayIntStatus();
//
// Verify that the interrupts were processed in the correct order.
//
if((g_ui32GPIOa != 3) || (g_ui32GPIOb != 2) || (g_ui32GPIOc != 1))
{
ui8Error |= 1;
}
//
// Wait two seconds.
//
Delay(2);
//
// Indicate that the decreasing interrupt priority test is beginning.
//
GrStringDrawCentered(&g_sContext, " Decreasing Pri ", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 20, 1);
//
// Set the interrupt priorities so that they are decreasing (i.e. C > B >
// A).
//
ROM_IntPrioritySet(INT_GPIOA, 0x80);
ROM_IntPrioritySet(INT_GPIOB, 0x40);
ROM_IntPrioritySet(INT_GPIOC, 0x00);
//
// Reset the interrupt flags.
//
g_ui32GPIOa = 0;
g_ui32GPIOb = 0;
g_ui32GPIOc = 0;
g_ui32Index = 1;
//
// Trigger the interrupt for GPIO C.
//
HWREG(NVIC_SW_TRIG) = INT_GPIOC - 16;
//
// Put the current interrupt state on the CSTN.
//
DisplayIntStatus();
//
// Verify that the interrupts were processed in the correct order.
//
if((g_ui32GPIOa != 3) || (g_ui32GPIOb != 2) || (g_ui32GPIOc != 1))
{
ui8Error |= 2;
}
//
// Wait two seconds.
//
Delay(2);
//
// Indicate that the increasing interrupt priority test is beginning.
//
GrStringDrawCentered(&g_sContext, " Increasing Pri ", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 20, 1);
//
// Set the interrupt priorities so that they are increasing (i.e. C < B <
// A).
//
ROM_IntPrioritySet(INT_GPIOA, 0x00);
ROM_IntPrioritySet(INT_GPIOB, 0x40);
ROM_IntPrioritySet(INT_GPIOC, 0x80);
//
// Reset the interrupt flags.
//
g_ui32GPIOa = 0;
g_ui32GPIOb = 0;
g_ui32GPIOc = 0;
g_ui32Index = 1;
//
// Trigger the interrupt for GPIO C.
//
HWREG(NVIC_SW_TRIG) = INT_GPIOC - 16;
//
// Put the current interrupt state on the CSTN.
//
DisplayIntStatus();
//
// Verify that the interrupts were processed in the correct order.
//
if((g_ui32GPIOa != 1) || (g_ui32GPIOb != 2) || (g_ui32GPIOc != 3))
{
ui8Error |= 4;
}
//
// Wait two seconds.
//
Delay(2);
//
// Disable the interrupts.
//
ROM_IntDisable(INT_GPIOA);
ROM_IntDisable(INT_GPIOB);
ROM_IntDisable(INT_GPIOC);
//
// Disable interrupts to the processor.
//
ROM_IntMasterDisable();
//
// Print out results if error occurred.
//
if(ui8Error)
{
GrStringDraw(&g_sContext, "Equal: P ", -1, 0, 32, 1);
GrStringDraw(&g_sContext, " Inc: P ", -1, 0, 44, 1);
GrStringDraw(&g_sContext, " Dec: P ", -1, 0, 56, 1);
if(ui8Error & 1)
{
GrStringDraw(&g_sContext, "F ", -1, 42, 32, 1);
}
if(ui8Error & 2)
{
GrStringDraw(&g_sContext, "F ", -1, 42, 44, 1);
}
if(ui8Error & 4)
{
GrStringDraw(&g_sContext, "F ", -1, 42, 56, 1);
}
}
else
{
GrStringDrawCentered(&g_sContext, " Success! ", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 20, 1);
}
//
// Flush the display.
//
GrFlush(&g_sContext);
//
// Loop forever.
//
while(1)
{
}
}
//*****************************************************************************
//
// Main application entry function.
//
//*****************************************************************************
int
main(void)
{
tBoolean bSuccess, bRetcode;
unsigned char pucMsg[2];
unsigned char ucTid;
unsigned char ucDelay;
unsigned long ulLastRxCount, ulLastTxCount;
smplStatus_t eRetcode;
//
// Set the system clock to run at 50MHz from the PLL
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// NB: We don't call PinoutSet() in this testcase since the EM header
// expansion board doesn't currently have an I2C ID EEPROM. If we did
// call PinoutSet() this would configure all the EPI pins for SDRAM and
// we don't want to do this.
//
g_eDaughterType = DAUGHTER_NONE;
//
// Enable peripherals required to drive the LCD.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOH);
//
// Configure SysTick for a 10Hz interrupt.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / TICKS_PER_SECOND);
ROM_SysTickEnable();
ROM_SysTickIntEnable();
//
// Initialize the display driver.
//
Kitronix320x240x16_SSD2119Init();
//
// Initialize the touch screen driver.
//
TouchScreenInit();
//
// Set the touch screen event handler.
//
TouchScreenCallbackSet(WidgetPointerMessage);
//
// Add the compile-time defined widgets to the widget tree.
//
WidgetAdd(WIDGET_ROOT, (tWidget *)&g_sHeading);
//
// Initialize the status string.
//
UpdateStatus(true, "Please choose the operating mode.");
//
// Paint the widget tree to make sure they all appear on the display.
//
WidgetPaint(WIDGET_ROOT);
//
// Initialize the SimpliciTI BSP.
//
BSP_Init();
//
// Set the SimpliciTI device address using the current Ethernet MAC address
// to ensure something like uniqueness.
//
bRetcode = SetSimpliciTIAddress();
if(!bRetcode)
{
//
// The board does not have a MAC address configured so we can't set
// the SimpliciTI device address (which we derive from the MAC address).
//
while(1);
}
//
// Initialize the SimpliciTI stack and supply our receive callback
// function pointer.
//
SMPL_Init(RxCallback);
//
// Initialize our message ID, initial inter-message delay and packet
// counters.
//
ucTid = 0;
ucDelay = 0;
ulLastRxCount = 0;
ulLastTxCount = 0;
//
// Fall into the command line processing loop.
//
while (1)
{
//
// Process any messages from or for the widgets.
//
WidgetMessageQueueProcess();
//
// Check to see if we've been told to do anything.
//
if(g_ulCommandFlags)
{
//
// Has the mode been set? If so, set up the display to show the
// "LEDs" and then start communication.
//
if(HWREGBITW(&g_ulCommandFlags, COMMAND_MODE_SET))
{
//
// Clear the bit now that we have seen it.
//
HWREGBITW(&g_ulCommandFlags, COMMAND_MODE_SET) = 0;
//
// Remove the buttons and replace them with the LEDs then
// repaint the display.
//
WidgetRemove((tWidget *)&g_sBtnContainer);
WidgetAdd((tWidget *)&g_sBackground,
(tWidget *)&g_sLEDContainer);
WidgetPaint((tWidget *)&g_sBackground);
//
// Now call the function that initiates communication in
// the desired mode. Note that these functions will not return
// until communication is established or an error occurs.
//
if(g_ulMode == MODE_TALKER)
{
bSuccess = LinkTo();
}
else
{
bSuccess = LinkFrom();
}
//
// If we were unsuccessfull, go back to the mode selection
// display.
//
if(!bSuccess)
{
//
// Remove the LEDs and show the buttons again.
//
WidgetRemove((tWidget *)&g_sLEDContainer);
WidgetAdd((tWidget *)&g_sBackground,
(tWidget *)&g_sBtnContainer);
WidgetPaint((tWidget *)&g_sBackground);
//
// Tell the user what happened.
//
UpdateStatus(false, "Error establishing communication!");
UpdateStatus(true, "Please choose the operating mode.");
//
// Remember that we don't have an operating mode chosen.
//
g_ulMode = MODE_UNDEFINED;
}
}
//
// Have we been asked to toggle the first "LED"?
//
if(HWREGBITW(&g_ulCommandFlags, COMMAND_LED1_TOGGLE))
{
//
// Clear the bit now that we have seen it.
//
HWREGBITW(&g_ulCommandFlags, COMMAND_LED1_TOGGLE) = 0;
//
// Toggle the LED.
//
ToggleLED(1);
}
//
// Have we been asked to toggle the second "LED"?
//
if(HWREGBITW(&g_ulCommandFlags, COMMAND_LED2_TOGGLE))
{
//
// Clear the bit now that we have seen it.
//
HWREGBITW(&g_ulCommandFlags, COMMAND_LED2_TOGGLE) = 0;
//
// Toggle the LED.
//
ToggleLED(2);
}
//
// Have we been asked to send a packet back to our peer? This
// command is only ever sent to the main loop when we are running
// in listener mode (LinkListen).
//
if(HWREGBITW(&g_ulCommandFlags, COMMAND_SEND_REPLY))
{
//
// Clear the bit now that we have seen it.
//
HWREGBITW(&g_ulCommandFlags, COMMAND_SEND_REPLY) = 0;
//
// Create the message. The first byte tells the receiver to
// toggle LED1 and the second is a sequence counter.
//
pucMsg[0] = 1;
pucMsg[1] = ++ucTid;
eRetcode = SMPL_Send(sLinkID, pucMsg, 2);
//
// Update our transmit counter if we transmitted the packet
// successfully.
//
if(eRetcode == SMPL_SUCCESS)
{
g_ulTxCount++;
}
else
{
UpdateStatus(false, "TX error %s (%d)", MapSMPLStatus(eRetcode),
eRetcode);
}
}
}
//
// If we are the talker (LinkTo mode), check to see if it's time to
// send another packet to our peer.
//
if((g_ulMode == MODE_TALKER) &&
(g_ulSysTickCount >= g_ulNextPacketTick))
{
//
// Create the message. The first byte tells the receiver to
// toggle LED1 and the second is a sequence counter.
//
pucMsg[0] = 1;
pucMsg[1] = ++ucTid;
eRetcode = SMPL_Send(sLinkID, pucMsg, 2);
//
// Update our transmit counter if we transmitted the packet
// correctly.
//
if(eRetcode == SMPL_SUCCESS)
{
g_ulTxCount++;
}
else
{
UpdateStatus(false, "TX error %s (%d)", MapSMPLStatus(eRetcode),
eRetcode);
}
//
// Set the delay before the next message.
//
#ifndef USE_2_SECOND_DELAY
//
// Set the delay before the next message. We increase this from 1
// second to 4 seconds then cycle back to 1.
//
ucDelay = (ucDelay == 4) ? 1 : (ucDelay + 1);
#else
//
// Wait 2 seconds before sending the next message.
//
ucDelay = 2;
#endif
//
// Calculate the system tick count when our delay has completed.
// This algorithm will generate a spurious packet every 13.7 years
// since I don't handle the rollover case in the comparison above
// but I'm pretty sure you will forgive me for this oversight.
//
g_ulNextPacketTick = g_ulSysTickCount +
(TICKS_PER_SECOND * ucDelay);
}
//
// If either the transmit or receive packet count changed, update
// the status on the display.
//
if((g_ulRxCount != ulLastRxCount) || (g_ulTxCount != ulLastTxCount))
{
ulLastTxCount = g_ulTxCount;
ulLastRxCount = g_ulRxCount;
UpdateStatus(false, "Received %d pkts, sent %d (%d)",
ulLastRxCount, ulLastTxCount);
}
}
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
unsigned long ulTxCount;
unsigned long ulRxCount;
tRectangle sRect;
char pcBuffer[16];
//
// Set the clocking to run from the PLL at 50MHz
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_8MHZ);
#ifdef DEBUG
//
// Configure the relevant pins such that UART0 owns them.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// Open UART0 for debug output.
//
UARTStdioInit(0);
#endif
//
// Not configured initially.
//
g_bUSBConfigured = false;
//
// Initialize the display driver.
//
Formike128x128x16Init();
//
// Turn on the backlight.
//
Formike128x128x16BacklightOn();
//
// Initialize the graphics context.
//
GrContextInit(&g_sContext, &g_sFormike128x128x16);
//
// Fill the top 15 rows of the screen with blue to create the banner.
//
sRect.sXMin = 0;
sRect.sYMin = 0;
sRect.sXMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.sYMax = 14;
GrContextForegroundSet(&g_sContext, ClrDarkBlue);
GrRectFill(&g_sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&g_sContext, ClrWhite);
GrRectDraw(&g_sContext, &sRect);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, g_pFontFixed6x8);
GrStringDrawCentered(&g_sContext, "usb_dev_bulk", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 7, 0);
//
// Show the various static text elements on the color STN display.
//
GrContextFontSet(&g_sContext, TEXT_FONT);
GrStringDraw(&g_sContext, "Tx bytes:", -1, 8, 70, false);
GrStringDraw(&g_sContext, "Rx bytes:", -1, 8, 90, false);
//
// Configure the USB mux on the board to put us in device mode. We pull
// the relevant pin high to do this.
//
ROM_SysCtlPeripheralEnable(USB_MUX_GPIO_PERIPH);
ROM_GPIOPinTypeGPIOOutput(USB_MUX_GPIO_BASE, USB_MUX_GPIO_PIN);
ROM_GPIOPinWrite(USB_MUX_GPIO_BASE, USB_MUX_GPIO_PIN, USB_MUX_SEL_DEVICE);
//
// Enable the system tick.
//
ROM_SysTickPeriodSet(SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Show the application name on the display and UART output.
//
DEBUG_PRINT("\nStellaris USB bulk device example\n");
DEBUG_PRINT("---------------------------------\n\n");
//
// Tell the user what we are up to.
//
DisplayStatus(&g_sContext, "Configuring USB...");
//
// Initialize the transmit and receive buffers.
//
USBBufferInit((tUSBBuffer *)&g_sTxBuffer);
USBBufferInit((tUSBBuffer *)&g_sRxBuffer);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDBulkInit(0, (tUSBDBulkDevice *)&g_sBulkDevice);
//
// Wait for initial configuration to complete.
//
DisplayStatus(&g_sContext, "Waiting for host...");
//
// Clear our local byte counters.
//
ulRxCount = 0;
ulTxCount = 0;
//
// Main application loop.
//
while(1)
{
//
// Have we been asked to update the status display?
//
if(g_ulFlags & COMMAND_STATUS_UPDATE)
{
//
// Clear the command flag
//
g_ulFlags &= ~COMMAND_STATUS_UPDATE;
DisplayStatus(&g_sContext, g_pcStatus);
}
//
// Has there been any transmit traffic since we last checked?
//
if(ulTxCount != g_ulTxCount)
{
//
// Take a snapshot of the latest transmit count.
//
ulTxCount = g_ulTxCount;
//
// Update the display of bytes transmitted by the UART.
//
usnprintf(pcBuffer, 16, "%d", ulTxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 70, 70, true);
}
//
// Has there been any receive traffic since we last checked?
//
if(ulRxCount != g_ulRxCount)
{
//
// Take a snapshot of the latest receive count.
//
ulRxCount = g_ulRxCount;
//
// Update the display of bytes received by the UART.
//
usnprintf(pcBuffer, 16, "%d", ulRxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 70, 90, true);
}
}
}
//*****************************************************************************
//
// This example demonstrates how to use the uDMA controller to transfer data
// between memory buffers and to and from a peripheral, in this case a UART.
// The uDMA controller is configured to repeatedly transfer a block of data
// from one memory buffer to another. It is also set up to repeatedly copy a
// block of data from a buffer to the UART output. The UART data is looped
// back so the same data is received, and the uDMA controlled is configured to
// continuously receive the UART data using ping-pong buffers.
//
// The processor is put to sleep when it is not doing anything, and this allows
// collection of CPU usage data to see how much CPU is being used while the
// data transfers are ongoing.
//
//*****************************************************************************
int
main(void)
{
static unsigned long ulPrevSeconds;
static unsigned long ulPrevXferCount;
static unsigned long ulPrevUARTCount = 0;
static char cStrBuf[40];
tRectangle sRect;
unsigned long ulCenterX;
unsigned long ulXfersCompleted;
unsigned long ulBytesTransferred;
//
// Set the clocking to run from the PLL at 50 MHz.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Set the device pinout appropriately for this board.
//
PinoutSet();
//
// Enable peripherals to operate when CPU is in sleep.
//
ROM_SysCtlPeripheralClockGating(true);
//
// Initialize the display driver.
//
Kitronix320x240x16_SSD2119Init();
//
// Initialize the graphics context and find the middle X coordinate.
//
GrContextInit(&g_sContext, &g_sKitronix320x240x16_SSD2119);
//
// Get the center X coordinate of the screen, since it is used a lot.
//
ulCenterX = GrContextDpyWidthGet(&g_sContext) / 2;
//
// Fill the top 15 rows of the screen with blue to create the banner.
//
sRect.sXMin = 0;
sRect.sYMin = 0;
sRect.sXMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.sYMax = 23;
GrContextForegroundSet(&g_sContext, ClrDarkBlue);
GrRectFill(&g_sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&g_sContext, ClrWhite);
GrRectDraw(&g_sContext, &sRect);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, g_pFontCm20);
GrStringDrawCentered(&g_sContext, "udma-demo", -1, ulCenterX, 11, 0);
//
// Show the clock frequency on the display.
//
GrContextFontSet(&g_sContext, g_pFontCmss18b);
usnprintf(cStrBuf, sizeof(cStrBuf), "Stellaris @ %u MHz",
SysCtlClockGet() / 1000000);
GrStringDrawCentered(&g_sContext, cStrBuf, -1, ulCenterX, 40, 0);
//
// Show static text and field labels on the display.
//
GrStringDrawCentered(&g_sContext, "uDMA Mem Transfers", -1,
ulCenterX, 62, 0);
GrStringDrawCentered(&g_sContext, "uDMA UART Transfers", -1,
ulCenterX, 84, 0);
//
// Configure SysTick to occur 100 times per second, to use as a time
// reference. Enable SysTick to generate interrupts.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Initialize the CPU usage measurement routine.
//
CPUUsageInit(SysCtlClockGet(), SYSTICKS_PER_SECOND, 2);
//
// Enable the uDMA controller at the system level. Enable it to continue
// to run while the processor is in sleep.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UDMA);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UDMA);
//
// Enable the uDMA controller error interrupt. This interrupt will occur
// if there is a bus error during a transfer.
//
ROM_IntEnable(INT_UDMAERR);
//
// Enable the uDMA controller.
//
ROM_uDMAEnable();
//
// Point at the control table to use for channel control structures.
//
ROM_uDMAControlBaseSet(ucControlTable);
//
// Initialize the uDMA memory to memory transfers.
//
InitSWTransfer();
//
// Initialize the uDMA UART transfers.
//
InitUART0Transfer();
//
// Remember the current SysTick seconds count.
//
ulPrevSeconds = g_ulSeconds;
//
// Remember the current count of memory buffer transfers.
//
ulPrevXferCount = g_ulMemXferCount;
//
// Loop until the button is pressed. The processor is put to sleep
// in this loop so that CPU utilization can be measured.
//
while(1)
{
//
// Check to see if one second has elapsed. If so, the make some
// updates.
//
if(g_ulSeconds != ulPrevSeconds)
{
//
// Print a message to the display showing the CPU usage percent.
// The fractional part of the percent value is ignored.
//
usnprintf(cStrBuf, sizeof(cStrBuf), "CPU utilization %2u%%",
g_ulCPUUsage >> 16);
GrStringDrawCentered(&g_sContext, cStrBuf, -1, ulCenterX, 160, 1);
//
// Tell the user how many seconds we have to go before ending.
//
usnprintf(cStrBuf, sizeof(cStrBuf), " Test ends in %d seconds ",
10 - g_ulSeconds);
GrStringDrawCentered(&g_sContext, cStrBuf, -1, ulCenterX, 120, 1);
//
// Remember the new seconds count.
//
ulPrevSeconds = g_ulSeconds;
//
// Calculate how many memory transfers have occurred since the last
// second.
//
ulXfersCompleted = g_ulMemXferCount - ulPrevXferCount;
//
// Remember the new transfer count.
//
ulPrevXferCount = g_ulMemXferCount;
//
// Compute how many bytes were transferred in the memory transfer
// since the last second.
//
ulBytesTransferred = ulXfersCompleted * MEM_BUFFER_SIZE * 4;
//
// Print a message to the display showing the memory transfer rate.
//
usnprintf(cStrBuf, sizeof(cStrBuf), " %8u Bytes/Sec ",
ulBytesTransferred);
GrStringDrawCentered(&g_sContext, cStrBuf, -1, ulCenterX, 182, 1);
//
// Calculate how many UART transfers have occurred since the last
// second.
//
ulXfersCompleted = (g_ulRxBufACount + g_ulRxBufBCount -
ulPrevUARTCount);
//
// Remember the new UART transfer count.
//
ulPrevUARTCount = g_ulRxBufACount + g_ulRxBufBCount;
//
// Compute how many bytes were transferred by the UART. The number
// of bytes received is multiplied by 2 so that the TX bytes
// transferred are also accounted for.
//
ulBytesTransferred = ulXfersCompleted * UART_RXBUF_SIZE * 2;
//
// Print a message to the display showing the UART transfer rate.
//
usnprintf(cStrBuf, sizeof(cStrBuf), " %8u Bytes/Sec ",
ulBytesTransferred);
GrStringDrawCentered(&g_sContext, cStrBuf, -1, ulCenterX, 204, 1);
}
//
// Put the processor to sleep if there is nothing to do. This allows
// the CPU usage routine to measure the number of free CPU cycles.
// If the processor is sleeping a lot, it can be hard to connect to
// the target with the debugger.
//
SysCtlSleep();
//
// See if we have run long enough and exit the loop if so.
//
if(g_ulSeconds >= 10)
{
break;
}
}
//*****************************************************************************
//
// Main 'C' Language entry point.
//
//*****************************************************************************
int
main(void)
{
float fTemperature, fPressure, fAltitude;
int32_t i32IntegerPart;
int32_t i32FractionPart;
//
// Setup the system clock to run at 40 MHz from PLL with crystal reference
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_5 | SYSCTL_USE_PLL | SYSCTL_XTAL_16MHZ |
SYSCTL_OSC_MAIN);
//
// Initialize the UART.
//
ConfigureUART();
//
// Print the welcome message to the terminal.
//
UARTprintf("\033[2JBMP180 Example\n");
//
// Set the color to a white approximation.
//
g_pui32Colors[RED] = 0x8000;
g_pui32Colors[BLUE] = 0x8000;
g_pui32Colors[GREEN] = 0x8000;
//
// Initialize RGB driver. Use a default intensity and blink rate.
//
RGBInit(0);
RGBColorSet(g_pui32Colors);
RGBIntensitySet(0.5f);
RGBEnable();
//
// The I2C3 peripheral must be enabled before use.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_I2C3);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
//
// Configure the pin muxing for I2C3 functions on port D0 and D1.
// This step is not necessary if your part does not support pin muxing.
//
ROM_GPIOPinConfigure(GPIO_PD0_I2C3SCL);
ROM_GPIOPinConfigure(GPIO_PD1_I2C3SDA);
//
// Select the I2C function for these pins. This function will also
// configure the GPIO pins pins for I2C operation, setting them to
// open-drain operation with weak pull-ups. Consult the data sheet
// to see which functions are allocated per pin.
//
GPIOPinTypeI2CSCL(GPIO_PORTD_BASE, GPIO_PIN_0);
ROM_GPIOPinTypeI2C(GPIO_PORTD_BASE, GPIO_PIN_1);
//
// Initialize the GPIO for the LED.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_1);
ROM_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_1, 0x00);
//
// Enable interrupts to the processor.
//
ROM_IntMasterEnable();
//
// Initialize the I2C3 peripheral.
//
I2CMInit(&g_sI2CInst, I2C3_BASE, INT_I2C3, 0xff, 0xff,
ROM_SysCtlClockGet());
//
// Initialize the BMP180.
//
BMP180Init(&g_sBMP180Inst, &g_sI2CInst, BMP180_I2C_ADDRESS,
BMP180AppCallback, &g_sBMP180Inst);
//
// Wait for initialization callback to indicate reset request is complete.
//
while(g_vui8DataFlag == 0)
{
//
// Wait for I2C Transactions to complete.
//
}
//
// Reset the data ready flag
//
g_vui8DataFlag = 0;
//
// Enable the system ticks at 10 Hz.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / (10 * 3));
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// After all the init and config we start blink the LED
//
RGBBlinkRateSet(1.0f);
//
// Begin the data collection and printing. Loop Forever.
//
while(1)
{
//
// Read the data from the BMP180 over I2C. This command starts a
// temperature measurement. Then polls until temperature is ready.
// Then automatically starts a pressure measurement and polls for that
// to complete. When both measurement are complete and in the local
// buffer then the application callback is called from the I2C
// interrupt context. Polling is done on I2C interrupts allowing
// processor to continue doing other tasks as needed.
//
BMP180DataRead(&g_sBMP180Inst, BMP180AppCallback, &g_sBMP180Inst);
while(g_vui8DataFlag == 0)
{
//
// Wait for the new data set to be available.
//
}
//
// Reset the data ready flag.
//
g_vui8DataFlag = 0;
//
// Get a local copy of the latest temperature data in float format.
//
BMP180DataTemperatureGetFloat(&g_sBMP180Inst, &fTemperature);
//
// Convert the floats to an integer part and fraction part for easy
// print.
//
i32IntegerPart = (int32_t) fTemperature;
i32FractionPart =(int32_t) (fTemperature * 1000.0f);
i32FractionPart = i32FractionPart - (i32IntegerPart * 1000);
if(i32FractionPart < 0)
{
i32FractionPart *= -1;
}
//
// Print temperature with three digits of decimal precision.
//
UARTprintf("Temperature %3d.%03d\t\t", i32IntegerPart, i32FractionPart);
//
// Get a local copy of the latest air pressure data in float format.
//
BMP180DataPressureGetFloat(&g_sBMP180Inst, &fPressure);
//
// Convert the floats to an integer part and fraction part for easy
// print.
//
i32IntegerPart = (int32_t) fPressure;
i32FractionPart =(int32_t) (fPressure * 1000.0f);
i32FractionPart = i32FractionPart - (i32IntegerPart * 1000);
if(i32FractionPart < 0)
{
i32FractionPart *= -1;
}
//
// Print Pressure with three digits of decimal precision.
//
UARTprintf("Pressure %3d.%03d\t\t", i32IntegerPart, i32FractionPart);
//
// Calculate the altitude.
//
fAltitude = 44330.0f * (1.0f - powf(fPressure / 101325.0f,
1.0f / 5.255f));
//
// Convert the floats to an integer part and fraction part for easy
// print.
//
i32IntegerPart = (int32_t) fAltitude;
i32FractionPart =(int32_t) (fAltitude * 1000.0f);
i32FractionPart = i32FractionPart - (i32IntegerPart * 1000);
if(i32FractionPart < 0)
{
i32FractionPart *= -1;
}
//
// Print altitude with three digits of decimal precision.
//
UARTprintf("Altitude %3d.%03d", i32IntegerPart, i32FractionPart);
//
// Print new line.
//
UARTprintf("\n");
//
// Delay to keep printing speed reasonable. About 100 milliseconds.
//
ROM_SysCtlDelay(ROM_SysCtlClockGet() / (10 * 3));
}//while end
}
//*****************************************************************************
//
// Compute and display a sine wave.
//
//*****************************************************************************
int
main(void)
{
uint_fast16_t ui16ItemCount = 0;
uint32_t ui32LastTickCount = 0;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run directly at 50 MHz.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_XTAL_16MHZ |
SYSCTL_OSC_MAIN);
//
// Configure SysTick to generate a periodic time tick interrupt.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / TICKS_PER_SECOND);
ROM_SysTickEnable();
ROM_SysTickIntEnable();
//
// Initialize the display driver.
//
CFAL96x64x16Init();
//
// Initialize an offscreen display and assign the palette. This offscreen
// buffer is needed by the strip chart widget.
//
GrOffScreen4BPPInit(&g_sOffscreenDisplay, g_pui8OffscreenBuf, 96, 64);
GrOffScreen4BPPPaletteSet(&g_sOffscreenDisplay, g_pui32Palette, 0,
NUM_PALETTE_ENTRIES);
//
// Set the data series buffer pointer to point at the storage where the
// series data points will be stored.
//
g_sSeries.pvData = g_i8SeriesData;
//
// Add the series to the strip chart
//
StripChartSeriesAdd(&g_sStripChart, &g_sSeries);
//
// Add the strip chart to the widget tree.
//
WidgetAdd(WIDGET_ROOT, &g_sStripChart.sBase);
//
// Enter a loop to continuously calculate a sine wave.
//
while(1)
{
float fElapsedTime;
float fRadians;
float fSine;
//
// Wait for the next timer tick.
//
while(ui32LastTickCount == g_ui32TickCount)
{
}
ui32LastTickCount = g_ui32TickCount;
//
// Preparing to add a new data point to the strip chart ...
// If the number count of items in the strip chart has reached the
// maximum value, then the data points need to "slide down" in the
// buffer so new data can be added at the end.
//
if(ui16ItemCount == SERIES_LENGTH)
{
memmove(&g_i8SeriesData[0], &g_i8SeriesData[1], SERIES_LENGTH - 1);
}
//
// Otherwise, the series data buffer is less than full so just
// increment the count of data points.
//
else
{
//
// Increment the number of items that have been added to the strip
// chart series data buffer.
//
ui16ItemCount++;
//
// Since the count of data items has changed, it must be updated in
// the data series.
//
g_sSeries.ui16NumItems = ui16ItemCount;
}
//
// Compute the elapsed time in decimal seconds, in floating point
// format.
//
fElapsedTime = (float)g_ui32TickCount * FSECONDS_PER_TICK;
//
// Convert the time to radians.
//
fRadians = fElapsedTime * 2.0 * M_PI;
//
// Adjust the period of the wave. This will give us a wave period
// of 4 seconds, or 0.25 Hz. This number was chosen arbitrarily to
// provide a nice looking wave on the display.
//
fRadians /= 4.0;
//
// Compute the sine. Multiply by 0.5 to reduce the amplitude.
//
fSine = sinf(fRadians) * 0.5;
//
// Finally, save the sine value into the last location in the series
// data point buffer. Convert the sine amplitude to display pixels.
// (Amplitude 1 = 32 pixels)
//
g_i8SeriesData[ui16ItemCount - 1] = (int8_t)(fSine * 32.0);
//
// Now that a new data point has been added to the series, advance
// the strip chart.
//
StripChartAdvance(&g_sStripChart, 1);
//
// Request a repaint and run the widget processing queue.
//
WidgetPaint(WIDGET_ROOT);
WidgetMessageQueueProcess();
}
}
//*****************************************************************************
//
// This is the main example program. It checks to see that the interrupts are
// processed in the correct order when they have identical priorities,
// increasing priorities, and decreasing priorities. This exercises interrupt
// preemption and tail chaining.
//
//*****************************************************************************
int
main(void)
{
uint_fast8_t ui8Error;
uint32_t ui32SysClock;
//
// Run from the PLL at 120 MHz.
//
ui32SysClock = MAP_SysCtlClockFreqSet((SYSCTL_XTAL_25MHZ |
SYSCTL_OSC_MAIN | SYSCTL_USE_PLL |
SYSCTL_CFG_VCO_480), 120000000);
//
// Configure the device pins.
//
PinoutSet();
//
// Initialize the display driver.
//
Kentec320x240x16_SSD2119Init(ui32SysClock);
//
// Initialize the graphics context.
//
GrContextInit(&g_sContext, &g_sKentec320x240x16_SSD2119);
//
// Draw the application frame.
//
FrameDraw(&g_sContext, "interrupts");
//
// Put the status header text on the display.
//
GrContextFontSet(&g_sContext, g_psFontCm20);
GrStringDrawCentered(&g_sContext, "Active: Pending: ", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 150, 0);
//
// Configure the B3, L1 and L0 to be outputs to indicate entry/exit of one
// of the interrupt handlers.
//
GPIOPinTypeGPIOOutput(GPIO_A_BASE, GPIO_A_PIN);
GPIOPinTypeGPIOOutput(GPIO_B_BASE, GPIO_B_PIN);
GPIOPinTypeGPIOOutput(GPIO_C_BASE, GPIO_C_PIN);
GPIOPinWrite(GPIO_A_BASE, GPIO_A_PIN, 0);
GPIOPinWrite(GPIO_B_BASE, GPIO_B_PIN, 0);
GPIOPinWrite(GPIO_C_BASE, GPIO_C_PIN, 0);
//
// Set up and enable the SysTick timer. It will be used as a reference
// for delay loops in the interrupt handlers. The SysTick timer period
// will be set up for 100 times per second.
//
ROM_SysTickPeriodSet(ui32SysClock / 100);
ROM_SysTickEnable();
//
// Reset the error indicator.
//
ui8Error = 0;
//
// Enable interrupts to the processor.
//
ROM_IntMasterEnable();
//
// Enable the interrupts.
//
ROM_IntEnable(INT_GPIOA);
ROM_IntEnable(INT_GPIOB);
ROM_IntEnable(INT_GPIOC);
//
// Indicate that the equal interrupt priority test is beginning.
//
GrStringDrawCentered(&g_sContext, "Equal Priority", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 60, 1);
//
// Set the interrupt priorities so they are all equal.
//
ROM_IntPrioritySet(INT_GPIOA, 0x00);
ROM_IntPrioritySet(INT_GPIOB, 0x00);
ROM_IntPrioritySet(INT_GPIOC, 0x00);
//
// Reset the interrupt flags.
//
g_ui32GPIOa = 0;
g_ui32GPIOb = 0;
g_ui32GPIOc = 0;
g_ui32Index = 1;
//
// Trigger the interrupt for GPIO C.
//
HWREG(NVIC_SW_TRIG) = INT_GPIOC - 16;
//
// Put the current interrupt state on the LCD.
//
DisplayIntStatus();
//
// Verify that the interrupts were processed in the correct order.
//
if((g_ui32GPIOa != 3) || (g_ui32GPIOb != 2) || (g_ui32GPIOc != 1))
{
ui8Error |= 1;
}
//
// Wait two seconds.
//
Delay(2);
//
// Indicate that the decreasing interrupt priority test is beginning.
//
GrStringDrawCentered(&g_sContext, " Decreasing Priority ", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 60, 1);
//
// Set the interrupt priorities so that they are decreasing (i.e. C > B >
// A).
//
ROM_IntPrioritySet(INT_GPIOA, 0x80);
ROM_IntPrioritySet(INT_GPIOB, 0x40);
ROM_IntPrioritySet(INT_GPIOC, 0x00);
//
// Reset the interrupt flags.
//
g_ui32GPIOa = 0;
g_ui32GPIOb = 0;
g_ui32GPIOc = 0;
g_ui32Index = 1;
//
// Trigger the interrupt for GPIO C.
//
HWREG(NVIC_SW_TRIG) = INT_GPIOC - 16;
//
// Put the current interrupt state on the display.
//
DisplayIntStatus();
//
// Verify that the interrupts were processed in the correct order.
//
if((g_ui32GPIOa != 3) || (g_ui32GPIOb != 2) || (g_ui32GPIOc != 1))
{
ui8Error |= 2;
}
//
// Wait two seconds.
//
Delay(2);
//
// Indicate that the increasing interrupt priority test is beginning.
//
GrStringDrawCentered(&g_sContext, " Increasing Priority ", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 60, 1);
//
// Set the interrupt priorities so that they are increasing (i.e. C < B <
// A).
//
ROM_IntPrioritySet(INT_GPIOA, 0x00);
ROM_IntPrioritySet(INT_GPIOB, 0x40);
ROM_IntPrioritySet(INT_GPIOC, 0x80);
//
// Reset the interrupt flags.
//
g_ui32GPIOa = 0;
g_ui32GPIOb = 0;
g_ui32GPIOc = 0;
g_ui32Index = 1;
//
// Trigger the interrupt for GPIO C.
//
HWREG(NVIC_SW_TRIG) = INT_GPIOC - 16;
//
// Put the current interrupt state on the display.
//
DisplayIntStatus();
//
// Verify that the interrupts were processed in the correct order.
//
if((g_ui32GPIOa != 1) || (g_ui32GPIOb != 2) || (g_ui32GPIOc != 3))
{
ui8Error |= 4;
}
//
// Wait two seconds.
//
Delay(2);
//
// Disable the interrupts.
//
ROM_IntDisable(INT_GPIOA);
ROM_IntDisable(INT_GPIOB);
ROM_IntDisable(INT_GPIOC);
//
// Disable interrupts to the processor.
//
ROM_IntMasterDisable();
//
// Print out the test results.
//
GrStringDrawCentered(&g_sContext, " Interrupt Priority ", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 60, 1);
if(ui8Error)
{
GrStringDrawCentered(&g_sContext, " Equal: P Inc: P Dec: P ",
-1, GrContextDpyWidthGet(&g_sContext) / 2, 150, 1);
if(ui8Error & 1)
{
GrStringDrawCentered(&g_sContext, " F ", -1, 113, 150, 1);
}
if(ui8Error & 2)
{
GrStringDrawCentered(&g_sContext, " F ", -1, 187, 150, 1);
}
if(ui8Error & 4)
{
GrStringDrawCentered(&g_sContext, " F ", -1, 272, 150, 1);
}
}
else
{
GrStringDrawCentered(&g_sContext, " Success! ", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 150, 1);
}
//
// Flush the display.
//
GrFlush(&g_sContext);
//
// Loop forever.
//
while(1)
{
}
}
//*****************************************************************************
//
// This is the main example program. It checks to see that the interrupts are
// processed in the correct order when they have identical priorities,
// increasing priorities, and decreasing priorities. This exercises interrupt
// preemption and tail chaining.
//
//*****************************************************************************
int
main(void)
{
uint32_t ui32Error;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run directly from the crystal.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Enable the peripherals used by this example.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
//
// Initialize the UART.
//
ConfigureUART();
UARTprintf("\033[2JInterrupts\n");
//
// Configure the PB0-PB2 to be outputs to indicate entry/exit of one
// of the interrupt handlers.
//
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTE_BASE, GPIO_PIN_1 | GPIO_PIN_2 |
GPIO_PIN_3);
ROM_GPIOPinWrite(GPIO_PORTE_BASE, GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3, 0);
//
// Set up and enable the SysTick timer. It will be used as a reference
// for delay loops in the interrupt handlers. The SysTick timer period
// will be set up for one second.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet());
ROM_SysTickEnable();
//
// Reset the error indicator.
//
ui32Error = 0;
//
// Enable interrupts to the processor.
//
ROM_IntMasterEnable();
//
// Enable the interrupts.
//
ROM_IntEnable(INT_GPIOA);
ROM_IntEnable(INT_GPIOB);
ROM_IntEnable(INT_GPIOC);
//
// Indicate that the equal interrupt priority test is beginning.
//
UARTprintf("\nEqual Priority\n");
//
// Set the interrupt priorities so they are all equal.
//
ROM_IntPrioritySet(INT_GPIOA, 0x00);
ROM_IntPrioritySet(INT_GPIOB, 0x00);
ROM_IntPrioritySet(INT_GPIOC, 0x00);
//
// Reset the interrupt flags.
//
g_ui32GPIOa = 0;
g_ui32GPIOb = 0;
g_ui32GPIOc = 0;
g_ui32Index = 1;
//
// Trigger the interrupt for GPIO C.
//
HWREG(NVIC_SW_TRIG) = INT_GPIOC - 16;
//
// Put the current interrupt state on the LCD.
//
DisplayIntStatus();
//
// Verify that the interrupts were processed in the correct order.
//
if((g_ui32GPIOa != 3) || (g_ui32GPIOb != 2) || (g_ui32GPIOc != 1))
{
ui32Error |= 1;
}
//
// Wait two seconds.
//
Delay(2);
//
// Indicate that the decreasing interrupt priority test is beginning.
//
UARTprintf("\nDecreasing Priority\n");
//
// Set the interrupt priorities so that they are decreasing (i.e. C > B >
// A).
//
ROM_IntPrioritySet(INT_GPIOA, 0x80);
ROM_IntPrioritySet(INT_GPIOB, 0x40);
ROM_IntPrioritySet(INT_GPIOC, 0x00);
//
// Reset the interrupt flags.
//
g_ui32GPIOa = 0;
g_ui32GPIOb = 0;
g_ui32GPIOc = 0;
g_ui32Index = 1;
//
// Trigger the interrupt for GPIO C.
//
HWREG(NVIC_SW_TRIG) = INT_GPIOC - 16;
//
// Put the current interrupt state on the UART.
//
DisplayIntStatus();
//
// Verify that the interrupts were processed in the correct order.
//
if((g_ui32GPIOa != 3) || (g_ui32GPIOb != 2) || (g_ui32GPIOc != 1))
{
ui32Error |= 2;
}
//
// Wait two seconds.
//
Delay(2);
//
// Indicate that the increasing interrupt priority test is beginning.
//
UARTprintf("\nIncreasing Priority\n");
//
// Set the interrupt priorities so that they are increasing (i.e. C < B <
// A).
//
ROM_IntPrioritySet(INT_GPIOA, 0x00);
ROM_IntPrioritySet(INT_GPIOB, 0x40);
ROM_IntPrioritySet(INT_GPIOC, 0x80);
//
// Reset the interrupt flags.
//
g_ui32GPIOa = 0;
g_ui32GPIOb = 0;
g_ui32GPIOc = 0;
g_ui32Index = 1;
//
// Trigger the interrupt for GPIO C.
//
HWREG(NVIC_SW_TRIG) = INT_GPIOC - 16;
//
// Put the current interrupt state on the UART.
//
DisplayIntStatus();
//
// Verify that the interrupts were processed in the correct order.
//
if((g_ui32GPIOa != 1) || (g_ui32GPIOb != 2) || (g_ui32GPIOc != 3))
{
ui32Error |= 4;
}
//
// Wait two seconds.
//
Delay(2);
//
// Disable the interrupts.
//
ROM_IntDisable(INT_GPIOA);
ROM_IntDisable(INT_GPIOB);
ROM_IntDisable(INT_GPIOC);
//
// Disable interrupts to the processor.
//
ROM_IntMasterDisable();
//
// Print out the test results.
//
UARTprintf("\nInterrupt Priority =: %s >: %s <: %s\n",
(ui32Error & 1) ? "Fail" : "Pass",
(ui32Error & 2) ? "Fail" : "Pass",
(ui32Error & 4) ? "Fail" : "Pass");
//
// Loop forever.
//
while(1)
{
}
}
//*****************************************************************************
//
// This is the main loop that runs the application.
//
//*****************************************************************************
int
main(void)
{
tRectangle sRect;
tUSBMode eLastMode;
char *pcString;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the system clock to run at 50MHz from the PLL.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Initially wait for device connection.
//
g_eUSBState = STATE_NO_DEVICE;
eLastMode = USB_MODE_OTG;
g_eCurrentUSBMode = USB_MODE_OTG;
//
// Enable Clocking to the USB controller.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_USB0);
//
// Configure the required pins for USB operation.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOG);
ROM_GPIOPinConfigure(GPIO_PG4_USB0EPEN);
ROM_GPIOPinTypeUSBDigital(GPIO_PORTG_BASE, GPIO_PIN_4);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOL);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTL_BASE, GPIO_PIN_6 | GPIO_PIN_7);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTB_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// Configure SysTick for a 100Hz interrupt.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / TICKS_PER_SECOND);
ROM_SysTickEnable();
ROM_SysTickIntEnable();
//
// Enable Interrupts
//
ROM_IntMasterEnable();
//
// Enable clocking to the UART and associated GPIO
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
//
// Configure the relevant pins such that UART0 owns them.
//
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// Open UART0 for debug output.
//
UARTStdioInit(0);
//
// Initialize the USB stack mode and pass in a mode callback.
//
USBStackModeSet(0, USB_MODE_OTG, ModeCallback);
//
// Register the host class drivers.
//
USBHCDRegisterDrivers(0, g_ppHostClassDrivers, g_ulNumHostClassDrivers);
//
// Open an instance of the keyboard driver. The keyboard does not need
// to be present at this time, this just save a place for it and allows
// the applications to be notified when a keyboard is present.
//
g_ulKeyboardInstance = USBHKeyboardOpen(KeyboardCallback, g_pucBuffer,
KEYBOARD_MEMORY_SIZE);
//
// Initialize the power configuration. This sets the power enable signal
// to be active high and does not enable the power fault.
//
USBHCDPowerConfigInit(0, USBHCD_VBUS_AUTO_HIGH | USBHCD_VBUS_FILTER);
//
// Initialize the USB controller for OTG operation with a 2ms polling
// rate.
//
USBOTGModeInit(0, 2000, g_pHCDPool, HCD_MEMORY_SIZE);
//
// Initialize the display driver.
//
CFAL96x64x16Init();
//
// Initialize the graphics context.
//
GrContextInit(&g_sContext, &g_sCFAL96x64x16);
//
// Fill the top part of the screen with blue to create the banner.
//
sRect.sXMin = 0;
sRect.sYMin = 0;
sRect.sXMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.sYMax = (2 * DISPLAY_BANNER_HEIGHT) - 1;
GrContextForegroundSet(&g_sContext, DISPLAY_BANNER_BG);
GrRectFill(&g_sContext, &sRect);
//
// Change foreground for white text.
//
GrContextForegroundSet(&g_sContext, DISPLAY_TEXT_FG);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, g_pFontFixed6x8);
GrStringDrawCentered(&g_sContext, "usb-host-", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 4, 0);
GrStringDrawCentered(&g_sContext, "keyboard", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 14, 0);
//
// Calculate the number of characters that will fit on a line.
// Make sure to leave a small border for the text box.
//
g_ulCharsPerLine = (GrContextDpyWidthGet(&g_sContext) - 4) /
GrFontMaxWidthGet(g_pFontFixed6x8);
//
// Calculate the number of lines per usable text screen. This requires
// taking off space for the top and bottom banners and adding a small bit
// for a border.
//
g_ulLinesPerScreen = (GrContextDpyHeightGet(&g_sContext) -
(3*(DISPLAY_BANNER_HEIGHT + 1)))/
GrFontHeightGet(g_pFontFixed6x8);
//
// Open and instance of the keyboard class driver.
//
UARTprintf("Host Keyboard Application\n");
//
// Initial update of the screen.
//
UpdateStatus();
//
// The main loop for the application.
//
while(1)
{
//
// Tell the OTG library code how much time has passed in
// milliseconds since the last call.
//
USBOTGMain(GetTickms());
//
// Has the USB mode changed since last time we checked?
//
if(g_eCurrentUSBMode != eLastMode)
{
//
// Remember the new mode.
//
eLastMode = g_eCurrentUSBMode;
switch(eLastMode)
{
case USB_MODE_HOST:
pcString = "HOST";
break;
case USB_MODE_DEVICE:
pcString = "DEVICE";
break;
case USB_MODE_NONE:
pcString = "NONE";
break;
default:
pcString = "UNKNOWN";
break;
}
UARTprintf("USB mode changed to %s\n", pcString);
}
switch(g_eUSBState)
{
//
// This state is entered when they keyboard is first detected.
//
case STATE_KEYBOARD_INIT:
{
//
// Initialized the newly connected keyboard.
//
USBHKeyboardInit(g_ulKeyboardInstance);
//
// Proceed to the keyboard connected state.
//
g_eUSBState = STATE_KEYBOARD_CONNECTED;
//
// Update the screen now that the keyboard has been
// initialized.
//
UpdateStatus();
USBHKeyboardModifierSet(g_ulKeyboardInstance, g_ulModifiers);
break;
}
case STATE_KEYBOARD_UPDATE:
{
//
// If the application detected a change that required an
// update to be sent to the keyboard to change the modifier
// state then call it and return to the connected state.
//
g_eUSBState = STATE_KEYBOARD_CONNECTED;
USBHKeyboardModifierSet(g_ulKeyboardInstance, g_ulModifiers);
break;
}
case STATE_KEYBOARD_CONNECTED:
{
//
// Nothing is currently done in the main loop when the keyboard
// is connected.
//
break;
}
case STATE_UNKNOWN_DEVICE:
{
//
// Nothing to do as the device is unknown.
//
break;
}
case STATE_NO_DEVICE:
{
//
// Nothing is currently done in the main loop when the keyboard
// is not connected.
//
break;
}
default:
{
break;
}
}
}
}
//*****************************************************************************
//
// Main application entry function.
//
//*****************************************************************************
int
main(void)
{
tBoolean bRetcode;
bspIState_t intState;
uint8_t ucLastChannel;
//
// Set the system clock to run at 50MHz from the PLL
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// NB: We don't call PinoutSet() in this testcase since the EM header
// expansion board doesn't currently have an I2C ID EEPROM. If we did
// call PinoutSet() this would configure all the EPI pins for SDRAM and
// we don't want to do this.
//
g_eDaughterType = DAUGHTER_NONE;
//
// Enable peripherals required to drive the LCD.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOH);
//
// Configure SysTick for a 10Hz interrupt.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / TICKS_PER_SECOND);
ROM_SysTickEnable();
ROM_SysTickIntEnable();
//
// Initialize the display driver.
//
Kitronix320x240x16_SSD2119Init();
//
// Initialize the touch screen driver.
//
TouchScreenInit();
//
// Set the touch screen event handler.
//
TouchScreenCallbackSet(WidgetPointerMessage);
//
// Add the compile-time defined widgets to the widget tree.
//
WidgetAdd(WIDGET_ROOT, (tWidget *)&g_sHeading);
//
// Initialize the status string.
//
UpdateStatus(true, "Initializing...");
//
// Paint the widget tree to make sure they all appear on the display.
//
WidgetPaint(WIDGET_ROOT);
//
// Initialize the SimpliciTI BSP.
//
BSP_Init();
//
// Set the SimpliciTI device address using the current Ethernet MAC address
// to ensure something like uniqueness.
//
bRetcode = SetSimpliciTIAddress();
//
// Did we have a problem with the address?
//
if(!bRetcode)
{
//
// Yes - make sure the display is updated then hang the app.
//
WidgetMessageQueueProcess();
while(1)
{
//
// MAC address is not set so hang the app.
//
}
}
//
// Turn on both our LEDs
//
SetLED(1, true);
SetLED(2, true);
UpdateStatus(true, "Waiting for a device...");
//
// Initialize the SimpliciTI stack and register our receive callback.
//
SMPL_Init(ReceiveCallback);
//
// Tell the user what's up.
//
UpdateStatus(true, "Access point active.");
//
// Do nothing after this - the SimpliciTI stack code handles all the
// access point function required.
//
while(1)
{
//
// Wait for the Join semaphore to be set by the receipt of a Join
// frame from a device that supports an end device.
//
// An external method could be used as well. A button press could be
// connected to an ISR and the ISR could set a semaphore that is
// checked by a function call here, or a command shell running in
// support of a serial connection could set a semaphore that is
// checked by a function call.
//
if (g_ucJoinSem && (g_ucNumCurrentPeers < NUM_CONNECTIONS))
{
//
// Listen for a new incoming connection.
//
while (1)
{
if (SMPL_SUCCESS == SMPL_LinkListen(&g_sLID[g_ucNumCurrentPeers]))
{
//
// The connection attempt succeeded so break out of the
// loop.
//
break;
}
//
// Process our widget message queue.
//
WidgetMessageQueueProcess();
//
// A "real" application would implement its fail-to-link
// policy here. We go back and listen again.
//
}
//
// Increment our peer counter.
//
g_ucNumCurrentPeers++;
//
// Decrement the join semaphore.
//
BSP_ENTER_CRITICAL_SECTION(intState);
g_ucJoinSem--;
BSP_EXIT_CRITICAL_SECTION(intState);
//
// Tell the user how many devices we are now connected to.
//
UpdateStatus(false, "%d devices connected.", g_ucNumCurrentPeers);
}
//
// Have we received a frame on one of the ED connections? We don't use
// a critical section here since it doesn't really matter much if we
// miss a poll.
//
if (g_ucPeerFrameSem)
{
uint8_t pucMsg[MAX_APP_PAYLOAD], ucLen, ucLoop;
/* process all frames waiting */
for (ucLoop = 0; ucLoop < g_ucNumCurrentPeers; ucLoop++)
{
//
// Receive the message.
//
if (SMPL_SUCCESS == SMPL_Receive(g_sLID[ucLoop], pucMsg,
&ucLen))
{
//
// ...and pass it to the function that processes it.
//
ProcessMessage(g_sLID[ucLoop], pucMsg, ucLen);
//
// Decrement our frame semaphore.
//
BSP_ENTER_CRITICAL_SECTION(intState);
g_ucPeerFrameSem--;
BSP_EXIT_CRITICAL_SECTION(intState);
}
}
}
//
// Have we been asked to change channel?
//
ucLastChannel = g_ucChannel;
if (g_bChangeChannel)
{
//
// Yes - go ahead and change to the next radio channel.
//
g_bChangeChannel = false;
ChangeChannel();
}
else
{
//
// No - check to see if we need to automatically change channel
// due to interference on the current one.
//
CheckChangeChannel();
}
//
// If the channel changed, update the display.
//
if(g_ucChannel != ucLastChannel)
{
UpdateStatus(false, "Changed to channel %d.", g_ucChannel);
}
//
// If required, blink the "LEDs" to indicate we are waiting for a
// message following a channel change.
//
BSP_ENTER_CRITICAL_SECTION(intState);
if (g_ulBlinky)
{
if (++g_ulBlinky >= 0xF)
{
g_ulBlinky = 1;
ToggleLED(1);
ToggleLED(2);
}
}
BSP_EXIT_CRITICAL_SECTION(intState);
//
// Process our widget message queue.
//
WidgetMessageQueueProcess();
}
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
uint_fast32_t ui32TxCount;
uint_fast32_t ui32RxCount;
tRectangle sRect;
char pcBuffer[16];
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run from the PLL at 50MHz
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
#ifdef DEBUG
//
// Configure the UART for debug output.
//
ConfigureUART();
#endif
//
// Not configured initially.
//
g_bUSBConfigured = false;
//
// Initialize the display driver.
//
CFAL96x64x16Init();
//
// Initialize the graphics context.
//
GrContextInit(&g_sContext, &g_sCFAL96x64x16);
//
// Fill the top part of the screen with blue to create the banner.
//
sRect.i16XMin = 0;
sRect.i16YMin = 0;
sRect.i16XMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.i16YMax = 9;
GrContextForegroundSet(&g_sContext, ClrDarkBlue);
GrRectFill(&g_sContext, &sRect);
//
// Change foreground for white text.
//
GrContextForegroundSet(&g_sContext, ClrWhite);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, g_psFontFixed6x8);
GrStringDrawCentered(&g_sContext, "usb-dev-bulk", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 4, 0);
//
// Show the various static text elements on the color STN display.
//
GrStringDraw(&g_sContext, "Tx bytes:", -1, 0, 32, false);
GrStringDraw(&g_sContext, "Rx bytes:", -1, 0, 42, false);
//
// Enable the GPIO peripheral used for USB, and configure the USB
// pins.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOL);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTB_BASE, GPIO_PIN_0 | GPIO_PIN_1);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTL_BASE, GPIO_PIN_6 | GPIO_PIN_7);
//
// Enable the system tick.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Show the application name on the display and UART output.
//
DEBUG_PRINT("\nTiva C Series USB bulk device example\n");
DEBUG_PRINT("---------------------------------\n\n");
//
// Tell the user what we are up to.
//
DisplayStatus(&g_sContext, "Configuring USB");
//
// Initialize the transmit and receive buffers.
//
USBBufferInit(&g_sTxBuffer);
USBBufferInit(&g_sRxBuffer);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDBulkInit(0, &g_sBulkDevice);
//
// Wait for initial configuration to complete.
//
DisplayStatus(&g_sContext, "Waiting for host");
//
// Clear our local byte counters.
//
ui32RxCount = 0;
ui32TxCount = 0;
//
// Main application loop.
//
while(1)
{
//
// Have we been asked to update the status display?
//
if(g_ui32Flags & COMMAND_STATUS_UPDATE)
{
//
// Clear the command flag
//
g_ui32Flags &= ~COMMAND_STATUS_UPDATE;
DisplayStatus(&g_sContext, g_pcStatus);
}
//
// Has there been any transmit traffic since we last checked?
//
if(ui32TxCount != g_ui32TxCount)
{
//
// Take a snapshot of the latest transmit count.
//
ui32TxCount = g_ui32TxCount;
//
// Update the display of bytes transmitted by the UART.
//
usnprintf(pcBuffer, 16, " %d ", ui32TxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 48, 32, true);
}
//
// Has there been any receive traffic since we last checked?
//
if(ui32RxCount != g_ui32RxCount)
{
//
// Take a snapshot of the latest receive count.
//
ui32RxCount = g_ui32RxCount;
//
// Update the display of bytes received by the UART.
//
usnprintf(pcBuffer, 16, " %d ", ui32RxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 48, 42, true);
}
}
}
//*****************************************************************************
//
// This is the main loop that runs the application.
//
//*****************************************************************************
int
main(void)
{
tRectangle sRect;
//
// Set the clocking to run from the PLL at 50MHz.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Initialize the display driver.
//
CFAL96x64x16Init();
//
// Initialize the graphics context.
//
GrContextInit(&g_sContext, &g_sCFAL96x64x16);
//
// Fill the top part of the screen with blue to create the banner.
//
sRect.i16XMin = 0;
sRect.i16YMin = 0;
sRect.i16XMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.i16YMax = (DISPLAY_BANNER_HEIGHT) - 1;
GrContextForegroundSet(&g_sContext, DISPLAY_BANNER_BG);
GrRectFill(&g_sContext, &sRect);
//
// Change foreground for white text.
//
GrContextForegroundSet(&g_sContext, DISPLAY_TEXT_FG);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, g_psFontFixed6x8);
GrStringDrawCentered(&g_sContext, "usb-host-mouse", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 4, 0);
//
// Display default information about the mouse
//
GrStringDrawCentered(&g_sContext, "Position:", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 16, 0);
GrStringDrawCentered(&g_sContext, "-,-", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 26, 1);
GrStringDrawCentered(&g_sContext, "Buttons:", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 36, 0);
GrStringDrawCentered(&g_sContext, "---", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 46, 1);
//
// Fill the bottom rows of the screen with blue to create the status area.
//
sRect.i16XMin = 0;
sRect.i16YMin = GrContextDpyHeightGet(&g_sContext) -
DISPLAY_BANNER_HEIGHT - 1;
sRect.i16XMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.i16YMax = sRect.i16YMin + DISPLAY_BANNER_HEIGHT;
GrContextForegroundSet(&g_sContext, DISPLAY_BANNER_BG);
GrRectFill(&g_sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&g_sContext, ClrWhite);
GrRectDraw(&g_sContext, &sRect);
//
// Print a no device message a placeholder for the message printed
// during an event.
//
GrStringDrawCentered(&g_sContext, "No Device", -1,
GrContextDpyWidthGet(&g_sContext) / 2,
sRect.i16YMin + 5, 0);
//
// Configure SysTick for a 100Hz interrupt.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / TICKS_PER_SECOND);
ROM_SysTickEnable();
ROM_SysTickIntEnable();
//
// Enable Clocking to the USB controller.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_USB0);
//
// Configure the required pins for USB operation.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOG);
ROM_GPIOPinConfigure(GPIO_PG4_USB0EPEN);
ROM_GPIOPinTypeUSBDigital(GPIO_PORTG_BASE, GPIO_PIN_4);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOL);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTL_BASE, GPIO_PIN_6 | GPIO_PIN_7);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTB_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// Initially wait for device connection.
//
g_eUSBState = STATE_NO_DEVICE;
//
// Initialize the USB stack mode and pass in a mode callback.
//
USBStackModeSet(0, eUSBModeOTG, ModeCallback);
//
// Register the host class drivers.
//
USBHCDRegisterDrivers(0, g_ppHostClassDrivers, g_ui32NumHostClassDrivers);
//
// Initialized the cursor.
//
g_ui32Buttons = 0;
g_i32CursorX = 0;
g_i32CursorY = 0;
//
// Open an instance of the mouse driver. The mouse does not need
// to be present at this time, this just saves a place for it and allows
// the applications to be notified when a mouse is present.
//
g_psMouseInstance =
USBHMouseOpen(MouseCallback, g_pui8Buffer, MOUSE_MEMORY_SIZE);
//
// Initialize the power configuration. This sets the power enable signal
// to be active high and does not enable the power fault.
//
USBHCDPowerConfigInit(0, USBHCD_VBUS_AUTO_HIGH | USBHCD_VBUS_FILTER);
//
// Initialize the USB controller for OTG operation with a 2ms polling
// rate.
//
USBOTGModeInit(0, 2000, g_pui8HCDPool, HCD_MEMORY_SIZE);
//
// The main loop for the application.
//
while(1)
{
//
// Tell the OTG state machine how much time has passed in
// milliseconds since the last call.
//
USBOTGMain(GetTickms());
switch(g_eUSBState)
{
//
// This state is entered when the mouse is first detected.
//
case STATE_MOUSE_INIT:
{
//
// Initialize the newly connected mouse.
//
USBHMouseInit(g_psMouseInstance);
//
// Proceed to the mouse connected state.
//
g_eUSBState = STATE_MOUSE_CONNECTED;
break;
}
case STATE_MOUSE_CONNECTED:
{
//
// Nothing is currently done in the main loop when the mouse
// is connected.
//
break;
}
case STATE_NO_DEVICE:
{
//
// The mouse is not connected so nothing needs to be done here.
//
break;
}
default:
{
break;
}
}
}
}
