static void bcmgenet_moca_phy_setup(struct bcmgenet_priv *priv)
{
u32 reg;
/* Speed settings are set in bcmgenet_mii_setup() */
reg = bcmgenet_sys_readl(priv, SYS_PORT_CTRL);
reg |= LED_ACT_SOURCE_MAC;
bcmgenet_sys_writel(priv, reg, SYS_PORT_CTRL);
}
static void bcmgenet_moca_phy_setup(struct bcmgenet_priv *priv)
{
u32 reg;
if (!GENET_IS_V5(priv)) {
/* Speed settings are set in bcmgenet_mii_setup() */
reg = bcmgenet_sys_readl(priv, SYS_PORT_CTRL);
reg |= LED_ACT_SOURCE_MAC;
bcmgenet_sys_writel(priv, reg, SYS_PORT_CTRL);
}
if (priv->hw_params->flags & GENET_HAS_MOCA_LINK_DET)
fixed_phy_set_link_update(priv->dev->phydev,
bcmgenet_fixed_phy_link_update);
}
int bcmgenet_mii_config(struct net_device *dev, bool init)
{
struct bcmgenet_priv *priv = netdev_priv(dev);
struct phy_device *phydev = priv->phydev;
struct device *kdev = &priv->pdev->dev;
const char *phy_name = NULL;
u32 id_mode_dis = 0;
u32 port_ctrl;
u32 reg;
priv->ext_phy = !phy_is_internal(priv->phydev) &&
(priv->phy_interface != PHY_INTERFACE_MODE_MOCA);
if (phy_is_internal(priv->phydev))
priv->phy_interface = PHY_INTERFACE_MODE_NA;
switch (priv->phy_interface) {
case PHY_INTERFACE_MODE_NA:
case PHY_INTERFACE_MODE_MOCA:
/* Irrespective of the actually configured PHY speed (100 or
* 1000) GENETv4 only has an internal GPHY so we will just end
* up masking the Gigabit features from what we support, not
* switching to the EPHY
*/
if (GENET_IS_V4(priv))
port_ctrl = PORT_MODE_INT_GPHY;
else
port_ctrl = PORT_MODE_INT_EPHY;
bcmgenet_sys_writel(priv, port_ctrl, SYS_PORT_CTRL);
if (phy_is_internal(priv->phydev)) {
phy_name = "internal PHY";
bcmgenet_internal_phy_setup(dev);
} else if (priv->phy_interface == PHY_INTERFACE_MODE_MOCA) {
phy_name = "MoCA";
bcmgenet_moca_phy_setup(priv);
}
break;
case PHY_INTERFACE_MODE_MII:
phy_name = "external MII";
phydev->supported &= PHY_BASIC_FEATURES;
bcmgenet_sys_writel(priv,
PORT_MODE_EXT_EPHY, SYS_PORT_CTRL);
break;
case PHY_INTERFACE_MODE_REVMII:
phy_name = "external RvMII";
/* of_mdiobus_register took care of reading the 'max-speed'
* PHY property for us, effectively limiting the PHY supported
* capabilities, use that knowledge to also configure the
* Reverse MII interface correctly.
*/
if ((priv->phydev->supported & PHY_BASIC_FEATURES) ==
PHY_BASIC_FEATURES)
port_ctrl = PORT_MODE_EXT_RVMII_25;
else
port_ctrl = PORT_MODE_EXT_RVMII_50;
bcmgenet_sys_writel(priv, port_ctrl, SYS_PORT_CTRL);
break;
case PHY_INTERFACE_MODE_RGMII:
/* RGMII_NO_ID: TXC transitions at the same time as TXD
* (requires PCB or receiver-side delay)
* RGMII: Add 2ns delay on TXC (90 degree shift)
*
* ID is implicitly disabled for 100Mbps (RG)MII operation.
*/
id_mode_dis = BIT(16);
/* fall through */
case PHY_INTERFACE_MODE_RGMII_TXID:
if (id_mode_dis)
phy_name = "external RGMII (no delay)";
else
phy_name = "external RGMII (TX delay)";
reg = bcmgenet_ext_readl(priv, EXT_RGMII_OOB_CTRL);
reg |= RGMII_MODE_EN | id_mode_dis;
bcmgenet_ext_writel(priv, reg, EXT_RGMII_OOB_CTRL);
bcmgenet_sys_writel(priv,
PORT_MODE_EXT_GPHY, SYS_PORT_CTRL);
break;
default:
dev_err(kdev, "unknown phy mode: %d\n", priv->phy_interface);
return -EINVAL;
}
if (init)
dev_info(kdev, "configuring instance for %s\n", phy_name);
return 0;
}
