Ejemplo n.º 1
0
/*
 * Create the appropriate control structures to manage
 * a new EHCI host controller.
 *
 * Excerpts from linux ehci fsl driver.
 */
int ehci_hcd_init(int index, enum usb_init_type init,
		struct ehci_hccr **hccr, struct ehci_hcor **hcor)
{
	struct usb_ehci *ehci = NULL;
	const char *phy_type = NULL;
	size_t len;
	char current_usb_controller[5];
#ifdef CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
	char usb_phy[5];

	usb_phy[0] = '\0';
#endif
	if (has_erratum_a007075()) {
		/*
		 * A 5ms delay is needed after applying soft-reset to the
		 * controller to let external ULPI phy come out of reset.
		 * This delay needs to be added before re-initializing
		 * the controller after soft-resetting completes
		 */
		mdelay(5);
	}
	memset(current_usb_controller, '\0', 5);
	snprintf(current_usb_controller, sizeof(current_usb_controller),
		 "usb%d", index+1);

	switch (index) {
	case 0:
		ehci = (struct usb_ehci *)CONFIG_SYS_FSL_USB1_ADDR;
		break;
	case 1:
		ehci = (struct usb_ehci *)CONFIG_SYS_FSL_USB2_ADDR;
		break;
	default:
		printf("ERROR: wrong controller index!!\n");
		return -EINVAL;
	};

	*hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
	*hcor = (struct ehci_hcor *)((uint32_t) *hccr +
			HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));

	/* Set to Host mode */
	setbits_le32(&ehci->usbmode, CM_HOST);

	out_be32(&ehci->snoop1, SNOOP_SIZE_2GB);
	out_be32(&ehci->snoop2, 0x80000000 | SNOOP_SIZE_2GB);

	/* Init phy */
	if (hwconfig_sub(current_usb_controller, "phy_type"))
		phy_type = hwconfig_subarg(current_usb_controller,
				"phy_type", &len);
	else
		phy_type = getenv("usb_phy_type");

	if (!phy_type) {
#ifdef CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
		/* if none specified assume internal UTMI */
		strcpy(usb_phy, "utmi");
		phy_type = usb_phy;
#else
		printf("WARNING: USB phy type not defined !!\n");
		return -1;
#endif
	}

	if (!strncmp(phy_type, "utmi", 4)) {
#if defined(CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY)
		clrsetbits_be32(&ehci->control, CONTROL_REGISTER_W1C_MASK,
				PHY_CLK_SEL_UTMI);
		clrsetbits_be32(&ehci->control, CONTROL_REGISTER_W1C_MASK,
				UTMI_PHY_EN);
		udelay(1000); /* delay required for PHY Clk to appear */
#endif
		out_le32(&(*hcor)->or_portsc[0], PORT_PTS_UTMI);
		clrsetbits_be32(&ehci->control, CONTROL_REGISTER_W1C_MASK,
				USB_EN);
	} else {
		clrsetbits_be32(&ehci->control, CONTROL_REGISTER_W1C_MASK,
				PHY_CLK_SEL_ULPI);
		clrsetbits_be32(&ehci->control, UTMI_PHY_EN |
				CONTROL_REGISTER_W1C_MASK, USB_EN);
		udelay(1000); /* delay required for PHY Clk to appear */
		if (!usb_phy_clk_valid(ehci))
			return -EINVAL;
		out_le32(&(*hcor)->or_portsc[0], PORT_PTS_ULPI);
	}

	out_be32(&ehci->prictrl, 0x0000000c);
	out_be32(&ehci->age_cnt_limit, 0x00000040);
	out_be32(&ehci->sictrl, 0x00000001);

	in_le32(&ehci->usbmode);

	if (has_erratum_a007798())
		set_txfifothresh(ehci, TXFIFOTHRESH);

	if (has_erratum_a004477()) {
		/*
		 * When reset is issued while any ULPI transaction is ongoing
		 * then it may result to corruption of ULPI Function Control
		 * Register which eventually causes phy clock to enter low
		 * power mode which stops the clock. Thus delay is required
		 * before reset to let ongoing ULPI transaction complete.
		 */
		udelay(1);
	}
	return 0;
}
Ejemplo n.º 2
0
static int prototype_board(void)
{
	if (hwconfig_subarg("board", "rev", NULL))
		return hwconfig_subarg_cmp("board", "rev", "prototype");
	return 1;
}