static void __init ux500_timer_init(void)
{
void __iomem *prcmu_timer_base;
if (cpu_is_u5500()) {
mtu_base = __io_address(U5500_MTU0_BASE);
prcmu_timer_base = __io_address(U5500_PRCMU_TIMER_3_BASE);
} else if (cpu_is_u8500()) {
mtu_base = __io_address(U8500_MTU0_BASE);
prcmu_timer_base = __io_address(U8500_PRCMU_TIMER_4_BASE);
} else {
ux500_unknown_soc();
}
/*
* Here we register the timerblocks active in the system.
* Localtimers (twd) is started when both cpu is up and running.
* MTU register a clocksource, clockevent and sched_clock.
* Since the MTU is located in the VAPE power domain
* it will be cleared in sleep which makes it unsuitable.
* We however need it as a timer tick (clockevent)
* during boot to calibrate delay until twd is started.
* RTC-RTT have problems as timer tick during boot since it is
* depending on delay which is not yet calibrated. RTC-RTT is in the
* always-on powerdomain and is used as clockevent instead of twd when
* sleeping.
* The PRCMU timer 4(3 for DB5500) register a clocksource and
* sched_clock with higher rating then MTU since is always-on.
*
*/
nmdk_timer_init();
clksrc_dbx500_prcmu_init(prcmu_timer_base);
ux500_twd_init();
}
static void __init nomadik_timer_init(void)
{
u32 src_cr;
/* Configure timer sources in "system reset controller" ctrl reg */
src_cr = readl(io_p2v(NOMADIK_SRC_BASE));
src_cr &= SRC_CR_INIT_MASK;
src_cr |= SRC_CR_INIT_VAL;
writel(src_cr, io_p2v(NOMADIK_SRC_BASE));
nmdk_timer_init(io_p2v(NOMADIK_MTU0_BASE), IRQ_MTU0);
}
void __init ux500_timer_init(void)
{
void __iomem *mtu_timer_base;
void __iomem *prcmu_timer_base;
void __iomem *tmp_base;
struct device_node *np;
if (cpu_is_u8500_family() || cpu_is_ux540_family()) {
mtu_timer_base = __io_address(U8500_MTU0_BASE);
prcmu_timer_base = __io_address(U8500_PRCMU_TIMER_4_BASE);
} else {
ux500_unknown_soc();
}
/* TODO: Once MTU has been DT:ed place code above into else. */
if (of_have_populated_dt()) {
#ifdef CONFIG_OF
np = of_find_matching_node(NULL, prcmu_timer_of_match);
if (!np)
#endif
goto dt_fail;
tmp_base = of_iomap(np, 0);
if (!tmp_base)
goto dt_fail;
prcmu_timer_base = tmp_base;
}
dt_fail:
/* Doing it the old fashioned way. */
/*
* Here we register the timerblocks active in the system.
* Localtimers (twd) is started when both cpu is up and running.
* MTU register a clocksource, clockevent and sched_clock.
* Since the MTU is located in the VAPE power domain
* it will be cleared in sleep which makes it unsuitable.
* We however need it as a timer tick (clockevent)
* during boot to calibrate delay until twd is started.
* RTC-RTT have problems as timer tick during boot since it is
* depending on delay which is not yet calibrated. RTC-RTT is in the
* always-on powerdomain and is used as clockevent instead of twd when
* sleeping.
* The PRCMU timer 4 register a clocksource and
* sched_clock with higher rating then MTU since is always-on.
*
*/
if (!of_have_populated_dt())
nmdk_timer_init(mtu_timer_base, IRQ_MTU0);
clksrc_dbx500_prcmu_init(prcmu_timer_base);
ux500_twd_init();
}
static void __init ux500_timer_init(void)
{
#ifdef CONFIG_LOCAL_TIMERS
/* Setup the local timer base */
twd_base = __io_address(UX500_TWD_BASE);
#endif
/* Setup the MTU base */
if (cpu_is_u8500ed())
mtu_base = __io_address(U8500_MTU0_BASE_ED);
else
mtu_base = __io_address(UX500_MTU0_BASE);
nmdk_timer_init();
}
static void __init nomadik_timer_init(void)
{
u32 src_cr;
/* Configure timer sources in "system reset controller" ctrl reg */
src_cr = readl(io_p2v(NOMADIK_SRC_BASE));
src_cr &= SRC_CR_INIT_MASK;
src_cr |= SRC_CR_INIT_VAL;
writel(src_cr, io_p2v(NOMADIK_SRC_BASE));
/* Save global pointer to mtu, used by platform timer code */
mtu_base = io_p2v(NOMADIK_MTU0_BASE);
nmdk_timer_init();
}
