/* This function is used to extract a board outlines (3D view, automatic zones build ...)
* Any closed outline inside the main outline is a hole
* All contours should be closed, i.e. valid closed polygon vertices
*/
bool BuildBoardPolygonOutlines( BOARD* aBoard, SHAPE_POLY_SET& aOutlines,
wxString* aErrorText, unsigned int aTolerance, wxPoint* aErrorLocation )
{
PCB_TYPE_COLLECTOR items;
// Get all the DRAWSEGMENTS and module graphics into 'items',
// then keep only those on layer == Edge_Cuts.
static const KICAD_T scan_graphics[] = { PCB_LINE_T, PCB_MODULE_EDGE_T, EOT };
items.Collect( aBoard, scan_graphics );
// Make a working copy of aSegList, because the list is modified during calculations
std::vector< DRAWSEGMENT* > segList;
for( int ii = 0; ii < items.GetCount(); ii++ )
{
if( items[ii]->GetLayer() == Edge_Cuts )
segList.push_back( static_cast< DRAWSEGMENT* >( items[ii] ) );
}
bool success = ConvertOutlineToPolygon( segList, aOutlines, aErrorText, aTolerance, aErrorLocation );
if( !success || !aOutlines.OutlineCount() )
{
// Creates a valid polygon outline is not possible.
// So uses the board edge cuts bounding box to create a
// rectangular outline
// When no edge cuts items, build a contour
// from global bounding box
EDA_RECT bbbox = aBoard->GetBoardEdgesBoundingBox();
// If null area, uses the global bounding box.
if( ( bbbox.GetWidth() ) == 0 || ( bbbox.GetHeight() == 0 ) )
bbbox = aBoard->ComputeBoundingBox();
// Ensure non null area. If happen, gives a minimal size.
if( ( bbbox.GetWidth() ) == 0 || ( bbbox.GetHeight() == 0 ) )
bbbox.Inflate( Millimeter2iu( 1.0 ) );
aOutlines.RemoveAllContours();
aOutlines.NewOutline();
wxPoint corner;
aOutlines.Append( bbbox.GetOrigin() );
corner.x = bbbox.GetOrigin().x;
corner.y = bbbox.GetEnd().y;
aOutlines.Append( corner );
aOutlines.Append( bbbox.GetEnd() );
corner.x = bbbox.GetEnd().x;
corner.y = bbbox.GetOrigin().y;
aOutlines.Append( corner );
}
return success;
}
SHAPE_POLY_SET* APERTURE_MACRO::GetApertureMacroShape( const GERBER_DRAW_ITEM* aParent,
wxPoint aShapePos )
{
SHAPE_POLY_SET holeBuffer;
bool hasHole = false;
m_shape.RemoveAllContours();
for( AM_PRIMITIVES::iterator prim_macro = primitives.begin();
prim_macro != primitives.end(); ++prim_macro )
{
if( prim_macro->primitive_id == AMP_COMMENT )
continue;
if( prim_macro->IsAMPrimitiveExposureOn( aParent ) )
prim_macro->DrawBasicShape( aParent, m_shape, aShapePos );
else
{
prim_macro->DrawBasicShape( aParent, holeBuffer, aShapePos );
if( holeBuffer.OutlineCount() ) // we have a new hole in shape: remove the hole
{
m_shape.BooleanSubtract( holeBuffer, SHAPE_POLY_SET::PM_FAST );
holeBuffer.RemoveAllContours();
hasHole = true;
}
}
}
// If a hole is defined inside a polygon, we must fracture the polygon
// to be able to drawn it (i.e link holes by overlapping edges)
if( hasHole )
m_shape.Fracture( SHAPE_POLY_SET::PM_FAST );
m_boundingBox = EDA_RECT( wxPoint( 0, 0 ), wxSize( 1, 1 ) );
auto bb = m_shape.BBox();
wxPoint center( bb.Centre().x, bb.Centre().y );
m_boundingBox.Move( aParent->GetABPosition( center ) );
m_boundingBox.Inflate( bb.GetWidth() / 2, bb.GetHeight() / 2 );
return &m_shape;
}
void EDA_3D_CANVAS::buildTechLayers3DView( REPORTER* aErrorMessages, REPORTER* aActivity )
{
BOARD* pcb = GetBoard();
bool useTextures = isRealisticMode() && isEnabled( FL_RENDER_TEXTURES );
// Number of segments to draw a circle using segments
const int segcountforcircle = 18;
double correctionFactor = 1.0 / cos( M_PI / (segcountforcircle * 2) );
const int segcountLowQuality = 12; // segments to draw a circle with low quality
// to reduce time calculations
// for holes and items which do not need
// a fine representation
double correctionFactorLQ = 1.0 / cos( M_PI / (segcountLowQuality * 2) );
// segments to draw a circle to build texts. Is is used only to build
// the shape of each segment of the stroke font, therefore no need to have
// many segments per circle.
const int segcountInStrokeFont = 8;
SHAPE_POLY_SET bufferPolys;
SHAPE_POLY_SET allLayerHoles; // Contains through holes, calculated only once
SHAPE_POLY_SET bufferPcbOutlines; // stores the board main outlines
// Build a polygon from edge cut items
wxString msg;
if( !pcb->GetBoardPolygonOutlines( bufferPcbOutlines, allLayerHoles, &msg ) )
{
if( aErrorMessages )
{
msg << wxT("\n") <<
_("Unable to calculate the board outlines.\n"
"Therefore use the board boundary box.") << wxT("\n\n");
aErrorMessages->Report( msg, REPORTER::RPT_WARNING );
}
}
// Build board holes, with no optimization of large holes shape.
buildBoardThroughHolesPolygonList( allLayerHoles, segcountLowQuality, false );
// draw graphic items, on technical layers
static const LAYER_ID teckLayerList[] = {
B_Adhes,
F_Adhes,
B_Paste,
F_Paste,
B_SilkS,
F_SilkS,
B_Mask,
F_Mask,
};
// User layers are not drawn here, only technical layers
for( LSEQ seq = LSET::AllTechMask().Seq( teckLayerList, DIM( teckLayerList ) ); seq; ++seq )
{
LAYER_ID layer = *seq;
if( !is3DLayerEnabled( layer ) )
continue;
if( layer == Edge_Cuts && isEnabled( FL_SHOW_BOARD_BODY ) )
continue;
if( aActivity )
aActivity->Report( wxString::Format( _( "Build layer %s" ), LSET::Name( layer ) ) );
bufferPolys.RemoveAllContours();
for( BOARD_ITEM* item = pcb->m_Drawings; item; item = item->Next() )
{
if( !item->IsOnLayer( layer ) )
continue;
switch( item->Type() )
{
case PCB_LINE_T:
( (DRAWSEGMENT*) item )->TransformShapeWithClearanceToPolygon(
bufferPolys, 0, segcountforcircle, correctionFactor );
break;
case PCB_TEXT_T:
( (TEXTE_PCB*) item )->TransformShapeWithClearanceToPolygonSet(
bufferPolys, 0, segcountLowQuality, 1.0 );
break;
default:
break;
}
}
for( MODULE* module = pcb->m_Modules; module; module = module->Next() )
{
if( layer == F_SilkS || layer == B_SilkS )
{
// On silk screen layers, the pad shape is only the pad outline
// never a filled shape
D_PAD* pad = module->Pads();
int linewidth = g_DrawDefaultLineThickness;
for( ; pad; pad = pad->Next() )
{
if( !pad->IsOnLayer( layer ) )
continue;
buildPadShapeThickOutlineAsPolygon( pad, bufferPolys,
linewidth, segcountforcircle, correctionFactor );
}
}
else
module->TransformPadsShapesWithClearanceToPolygon( layer,
bufferPolys, 0, segcountforcircle, correctionFactor );
// On tech layers, use a poor circle approximation, only for texts (stroke font)
module->TransformGraphicShapesWithClearanceToPolygonSet( layer,
bufferPolys, 0, segcountforcircle, correctionFactor, segcountInStrokeFont );
}
// Draw non copper zones
if( isEnabled( FL_ZONE ) )
{
for( int ii = 0; ii < pcb->GetAreaCount(); ii++ )
{
ZONE_CONTAINER* zone = pcb->GetArea( ii );
if( !zone->IsOnLayer( layer ) )
continue;
zone->TransformSolidAreasShapesToPolygonSet(
bufferPolys, segcountLowQuality, correctionFactorLQ );
}
}
// bufferPolys contains polygons to merge. Many overlaps .
// Calculate merged polygons and remove pads and vias holes
if( bufferPolys.IsEmpty() )
continue;
// Solder mask layers are "negative" layers.
// Shapes should be removed from the full board area.
if( layer == B_Mask || layer == F_Mask )
{
SHAPE_POLY_SET cuts = bufferPolys;
bufferPolys = bufferPcbOutlines;
cuts.Append(allLayerHoles);
cuts.Simplify();
bufferPolys.BooleanSubtract( cuts );
}
// Remove holes from Solder paste layers and silkscreen
else if( layer == B_Paste || layer == F_Paste
|| layer == B_SilkS || layer == F_SilkS )
{
bufferPolys.BooleanSubtract( allLayerHoles );
}
int thickness = 0;
if( layer != B_Mask && layer != F_Mask )
thickness = GetPrm3DVisu().GetLayerObjectThicknessBIU( layer );
int zpos = GetPrm3DVisu().GetLayerZcoordBIU( layer );
if( layer == Edge_Cuts )
{
thickness = GetPrm3DVisu().GetLayerZcoordBIU( F_Cu )
- GetPrm3DVisu().GetLayerZcoordBIU( B_Cu );
zpos = GetPrm3DVisu().GetLayerZcoordBIU( B_Cu )
+ (thickness / 2);
}
else
{
// for Draw3D_SolidHorizontalPolyPolygons, zpos it the middle between bottom and top
// sides.
// However for top layers, zpos should be the bottom layer pos,
// and for bottom layers, zpos should be the top layer pos.
if( Get3DLayer_Z_Orientation( layer ) > 0 )
zpos += thickness/2;
else
zpos -= thickness/2 ;
}
float zNormal = 1.0f; // When using thickness it will draw first the top and then botton (with z inverted)
// If we are not using thickness, then the znormal must face the layer direction
// because it will draw just one plane
if( !thickness )
zNormal = Get3DLayer_Z_Orientation( layer );
setGLTechLayersColor( layer );
Draw3D_SolidHorizontalPolyPolygons( bufferPolys, zpos,
thickness, GetPrm3DVisu().m_BiuTo3Dunits, useTextures,
zNormal );
}
}
void EDA_3D_CANVAS::buildBoard3DView( GLuint aBoardList, GLuint aBodyOnlyList,
REPORTER* aErrorMessages, REPORTER* aActivity )
{
BOARD* pcb = GetBoard();
// If FL_RENDER_SHOW_HOLES_IN_ZONES is true, holes are correctly removed from copper zones areas.
// If FL_RENDER_SHOW_HOLES_IN_ZONES is false, holes are not removed from copper zones areas,
// but the calculation time is twice shorter.
bool remove_Holes = isEnabled( FL_RENDER_SHOW_HOLES_IN_ZONES );
bool realistic_mode = isRealisticMode();
bool useTextures = isRealisticMode() && isEnabled( FL_RENDER_TEXTURES );
// Number of segments to convert a circle to polygon
// We use 2 values: the first gives a good shape (for instanes rond pads)
// the second is used to speed up calculations, when a poor approximation is acceptable (holes)
const int segcountforcircle = 18;
double correctionFactor = 1.0 / cos( M_PI / (segcountforcircle * 2.0) );
const int segcountLowQuality = 12; // segments to draw a circle with low quality
// to reduce time calculations
// for holes and items which do not need
// a fine representation
double correctionFactorLQ = 1.0 / cos( M_PI / (segcountLowQuality * 2.0) );
SHAPE_POLY_SET bufferPolys; // copper areas: tracks, pads and filled zones areas
// when holes are removed from zones
SHAPE_POLY_SET bufferPcbOutlines; // stores the board main outlines
SHAPE_POLY_SET bufferZonesPolys; // copper filled zones areas
// when holes are not removed from zones
SHAPE_POLY_SET currLayerHoles; // Contains holes for the current layer
SHAPE_POLY_SET allLayerHoles; // Contains holes for all layers
// Build a polygon from edge cut items
wxString msg;
if( !pcb->GetBoardPolygonOutlines( bufferPcbOutlines, allLayerHoles, &msg ) )
{
if( aErrorMessages )
{
msg << wxT("\n") << _("Unable to calculate the board outlines.\n"
"Therefore use the board boundary box.") << wxT("\n\n");
aErrorMessages->Report( msg, REPORTER::RPT_WARNING );
}
}
// Build board holes, with optimization of large holes shape.
buildBoardThroughHolesPolygonList( allLayerHoles, segcountLowQuality, true );
LSET cu_set = LSET::AllCuMask( GetPrm3DVisu().m_CopperLayersCount );
glNewList( aBoardList, GL_COMPILE );
for( LSEQ cu = cu_set.CuStack(); cu; ++cu )
{
LAYER_ID layer = *cu;
// Skip non enabled layers in normal mode,
// and internal layers in realistic mode
if( !is3DLayerEnabled( layer ) )
continue;
if( aActivity )
aActivity->Report( wxString::Format( _( "Build layer %s" ), LSET::Name( layer ) ) );
bufferPolys.RemoveAllContours();
bufferZonesPolys.RemoveAllContours();
currLayerHoles.RemoveAllContours();
// Draw track shapes:
for( TRACK* track = pcb->m_Track; track; track = track->Next() )
{
if( !track->IsOnLayer( layer ) )
continue;
track->TransformShapeWithClearanceToPolygon( bufferPolys,
0, segcountforcircle,
correctionFactor );
// Add blind/buried via holes
if( track->Type() == PCB_VIA_T )
{
VIA *via = static_cast<VIA*>( track );
if( via->GetViaType() == VIA_THROUGH )
continue; // already done
int holediameter = via->GetDrillValue();
int thickness = GetPrm3DVisu().GetCopperThicknessBIU();
int hole_outer_radius = (holediameter + thickness) / 2;
TransformCircleToPolygon( currLayerHoles,
via->GetStart(), hole_outer_radius,
segcountLowQuality );
}
}
// draw pad shapes
for( MODULE* module = pcb->m_Modules; module; module = module->Next() )
{
// Note: NPTH pads are not drawn on copper layers when the pad
// has same shape as its hole
module->TransformPadsShapesWithClearanceToPolygon( layer,
bufferPolys,
0,
segcountforcircle,
correctionFactor, true );
// Micro-wave modules may have items on copper layers
module->TransformGraphicShapesWithClearanceToPolygonSet( layer,
bufferPolys,
0,
segcountforcircle,
correctionFactor );
// pad holes are already in list.
}
// Draw copper zones. Note:
// * if the holes are removed from copper zones
// the polygons are stored in bufferPolys (which contains all other polygons)
// * if the holes are NOT removed from copper zones
// the polygons are stored in bufferZonesPolys
if( isEnabled( FL_ZONE ) )
{
for( int ii = 0; ii < pcb->GetAreaCount(); ii++ )
{
ZONE_CONTAINER* zone = pcb->GetArea( ii );
LAYER_NUM zonelayer = zone->GetLayer();
if( zonelayer == layer )
{
zone->TransformSolidAreasShapesToPolygonSet(
remove_Holes ? bufferPolys : bufferZonesPolys,
segcountLowQuality, correctionFactorLQ );
}
}
}
// draw graphic items on copper layers (texts)
for( BOARD_ITEM* item = pcb->m_Drawings; item; item = item->Next() )
{
if( !item->IsOnLayer( layer ) )
continue;
switch( item->Type() )
{
case PCB_LINE_T: // should not exist on copper layers
( (DRAWSEGMENT*) item )->TransformShapeWithClearanceToPolygon(
bufferPolys, 0, segcountforcircle, correctionFactor );
break;
case PCB_TEXT_T:
( (TEXTE_PCB*) item )->TransformShapeWithClearanceToPolygonSet(
bufferPolys, 0, segcountLowQuality, correctionFactor );
break;
default:
break;
}
}
// bufferPolys contains polygons to merge. Many overlaps .
// Calculate merged polygons
if( bufferPolys.IsEmpty() )
continue;
// Use Clipper lib to subtract holes to copper areas
if( currLayerHoles.OutlineCount() )
{
currLayerHoles.Append(allLayerHoles);
currLayerHoles.Simplify();
bufferPolys.BooleanSubtract( currLayerHoles );
}
else
bufferPolys.BooleanSubtract( allLayerHoles );
int thickness = GetPrm3DVisu().GetLayerObjectThicknessBIU( layer );
int zpos = GetPrm3DVisu().GetLayerZcoordBIU( layer );
float zNormal = 1.0f; // When using thickness it will draw first the top and then botton (with z inverted)
// If we are not using thickness, then the z-normal has to match the layer direction
// because just one plane will be drawn
if( !thickness )
zNormal = Get3DLayer_Z_Orientation( layer );
if( realistic_mode )
{
setGLCopperColor();
}
else
{
EDA_COLOR_T color = g_ColorsSettings.GetLayerColor( layer );
SetGLColor( color );
}
// If holes are removed from copper zones, bufferPolys contains all polygons
// to draw (tracks+zones+texts).
Draw3D_SolidHorizontalPolyPolygons( bufferPolys, zpos, thickness,
GetPrm3DVisu().m_BiuTo3Dunits, useTextures,
zNormal );
// If holes are not removed from copper zones (for calculation time reasons,
// the zone polygons are stored in bufferZonesPolys and have to be drawn now:
if( !bufferZonesPolys.IsEmpty() )
{
Draw3D_SolidHorizontalPolyPolygons( bufferZonesPolys, zpos, thickness,
GetPrm3DVisu().m_BiuTo3Dunits, useTextures,
zNormal );
}
}
if( aActivity )
aActivity->Report( _( "Build board body" ) );
// Draw plated vertical holes inside the board, but not always. They are drawn:
// - if the board body is not shown, to show the holes.
// - or if the copper thickness is shown
if( !isEnabled( FL_SHOW_BOARD_BODY ) || isEnabled( FL_USE_COPPER_THICKNESS ) )
{
// Draw vias holes (vertical cylinders)
for( const TRACK* track = pcb->m_Track; track; track = track->Next() )
{
if( track->Type() == PCB_VIA_T )
{
const VIA *via = static_cast<const VIA*>(track);
draw3DViaHole( via );
}
}
// Draw pads holes (vertical cylinders)
for( const MODULE* module = pcb->m_Modules; module; module = module->Next() )
{
for( D_PAD* pad = module->Pads(); pad; pad = pad->Next() )
if( pad->GetAttribute () != PAD_HOLE_NOT_PLATED )
draw3DPadHole( pad );
}
}
glEndList();
// Build the body board:
glNewList( aBodyOnlyList, GL_COMPILE );
if( isRealisticMode() )
{
setGLEpoxyColor( 1.00 );
}
else
{
EDA_COLOR_T color = g_ColorsSettings.GetLayerColor( Edge_Cuts );
SetGLColor( color, 0.7 );
}
float copper_thickness = GetPrm3DVisu().GetCopperThicknessBIU();
// a small offset between substrate and external copper layer to avoid artifacts
// when drawing copper items on board
float epsilon = Millimeter2iu( 0.01 );
float zpos = GetPrm3DVisu().GetLayerZcoordBIU( B_Cu );
float board_thickness = GetPrm3DVisu().GetLayerZcoordBIU( F_Cu )
- GetPrm3DVisu().GetLayerZcoordBIU( B_Cu );
// items on copper layers and having a thickness = copper_thickness
// are drawn from zpos - copper_thickness/2 to zpos + copper_thickness
// therefore substrate position is copper_thickness/2 to
// substrate_height - copper_thickness/2
zpos += (copper_thickness + epsilon) / 2.0f;
board_thickness -= copper_thickness + epsilon;
bufferPcbOutlines.BooleanSubtract( allLayerHoles );
if( !bufferPcbOutlines.IsEmpty() )
{
Draw3D_SolidHorizontalPolyPolygons( bufferPcbOutlines, zpos + board_thickness / 2.0,
board_thickness, GetPrm3DVisu().m_BiuTo3Dunits, useTextures,
1.0f );
}
glEndList();
}
void ZONE_CONTAINER::buildFeatureHoleList( BOARD* aPcb, SHAPE_POLY_SET& aFeatures )
{
int segsPerCircle;
double correctionFactor;
// Set the number of segments in arc approximations
if( m_ArcToSegmentsCount == ARC_APPROX_SEGMENTS_COUNT_HIGHT_DEF )
segsPerCircle = ARC_APPROX_SEGMENTS_COUNT_HIGHT_DEF;
else
segsPerCircle = ARC_APPROX_SEGMENTS_COUNT_LOW_DEF;
/* calculates the coeff to compensate radius reduction of holes clearance
* due to the segment approx.
* For a circle the min radius is radius * cos( 2PI / s_CircleToSegmentsCount / 2)
* s_Correction is 1 /cos( PI/s_CircleToSegmentsCount )
*/
correctionFactor = 1.0 / cos( M_PI / (double) segsPerCircle );
aFeatures.RemoveAllContours();
int outline_half_thickness = m_ZoneMinThickness / 2;
int zone_clearance = std::max( m_ZoneClearance, GetClearance() );
zone_clearance += outline_half_thickness;
/* store holes (i.e. tracks and pads areas as polygons outlines)
* in a polygon list
*/
/* items ouside the zone bounding box are skipped
* the bounding box is the zone bounding box + the biggest clearance found in Netclass list
*/
EDA_RECT item_boundingbox;
EDA_RECT zone_boundingbox = GetBoundingBox();
int biggest_clearance = aPcb->GetDesignSettings().GetBiggestClearanceValue();
biggest_clearance = std::max( biggest_clearance, zone_clearance );
zone_boundingbox.Inflate( biggest_clearance );
/*
* First : Add pads. Note: pads having the same net as zone are left in zone.
* Thermal shapes will be created later if necessary
*/
int item_clearance;
/* Use a dummy pad to calculate hole clerance when a pad is not on all copper layers
* and this pad has a hole
* This dummy pad has the size and shape of the hole
* Therefore, this dummy pad is a circle or an oval.
* A pad must have a parent because some functions expect a non null parent
* to find the parent board, and some other data
*/
MODULE dummymodule( aPcb ); // Creates a dummy parent
D_PAD dummypad( &dummymodule );
for( MODULE* module = aPcb->m_Modules; module; module = module->Next() )
{
D_PAD* nextpad;
for( D_PAD* pad = module->Pads(); pad != NULL; pad = nextpad )
{
nextpad = pad->Next(); // pad pointer can be modified by next code, so
// calculate the next pad here
if( !pad->IsOnLayer( GetLayer() ) )
{
/* Test for pads that are on top or bottom only and have a hole.
* There are curious pads but they can be used for some components that are
* inside the board (in fact inside the hole. Some photo diodes and Leds are
* like this)
*/
if( pad->GetDrillSize().x == 0 && pad->GetDrillSize().y == 0 )
continue;
// Use a dummy pad to calculate a hole shape that have the same dimension as
// the pad hole
dummypad.SetSize( pad->GetDrillSize() );
dummypad.SetOrientation( pad->GetOrientation() );
dummypad.SetShape( pad->GetDrillShape() == PAD_DRILL_SHAPE_OBLONG ?
PAD_SHAPE_OVAL : PAD_SHAPE_CIRCLE );
dummypad.SetPosition( pad->GetPosition() );
pad = &dummypad;
}
// Note: netcode <=0 means not connected item
if( ( pad->GetNetCode() != GetNetCode() ) || ( pad->GetNetCode() <= 0 ) )
{
item_clearance = pad->GetClearance() + outline_half_thickness;
item_boundingbox = pad->GetBoundingBox();
item_boundingbox.Inflate( item_clearance );
if( item_boundingbox.Intersects( zone_boundingbox ) )
{
int clearance = std::max( zone_clearance, item_clearance );
pad->TransformShapeWithClearanceToPolygon( aFeatures,
clearance,
segsPerCircle,
correctionFactor );
}
continue;
}
// Pads are removed from zone if the setup is PAD_ZONE_CONN_NONE
if( GetPadConnection( pad ) == PAD_ZONE_CONN_NONE )
{
int gap = zone_clearance;
int thermalGap = GetThermalReliefGap( pad );
gap = std::max( gap, thermalGap );
item_boundingbox = pad->GetBoundingBox();
item_boundingbox.Inflate( gap );
if( item_boundingbox.Intersects( zone_boundingbox ) )
{
pad->TransformShapeWithClearanceToPolygon( aFeatures,
gap,
segsPerCircle,
correctionFactor );
}
}
}
}
/* Add holes (i.e. tracks and vias areas as polygons outlines)
* in cornerBufferPolysToSubstract
*/
for( TRACK* track = aPcb->m_Track; track; track = track->Next() )
{
if( !track->IsOnLayer( GetLayer() ) )
continue;
if( track->GetNetCode() == GetNetCode() && (GetNetCode() != 0) )
continue;
item_clearance = track->GetClearance() + outline_half_thickness;
item_boundingbox = track->GetBoundingBox();
if( item_boundingbox.Intersects( zone_boundingbox ) )
{
int clearance = std::max( zone_clearance, item_clearance );
track->TransformShapeWithClearanceToPolygon( aFeatures,
clearance,
segsPerCircle,
correctionFactor );
}
}
/* Add module edge items that are on copper layers
* Pcbnew allows these items to be on copper layers in microwave applictions
* This is a bad thing, but must be handled here, until a better way is found
*/
for( MODULE* module = aPcb->m_Modules; module; module = module->Next() )
{
for( BOARD_ITEM* item = module->GraphicalItems(); item; item = item->Next() )
{
if( !item->IsOnLayer( GetLayer() ) && !item->IsOnLayer( Edge_Cuts ) )
continue;
if( item->Type() != PCB_MODULE_EDGE_T )
continue;
item_boundingbox = item->GetBoundingBox();
if( item_boundingbox.Intersects( zone_boundingbox ) )
{
( (EDGE_MODULE*) item )->TransformShapeWithClearanceToPolygon(
aFeatures, zone_clearance,
segsPerCircle, correctionFactor );
}
}
}
// Add graphic items (copper texts) and board edges
for( BOARD_ITEM* item = aPcb->m_Drawings; item; item = item->Next() )
{
if( item->GetLayer() != GetLayer() && item->GetLayer() != Edge_Cuts )
continue;
switch( item->Type() )
{
case PCB_LINE_T:
( (DRAWSEGMENT*) item )->TransformShapeWithClearanceToPolygon(
aFeatures,
zone_clearance, segsPerCircle, correctionFactor );
break;
case PCB_TEXT_T:
( (TEXTE_PCB*) item )->TransformBoundingBoxWithClearanceToPolygon(
aFeatures, zone_clearance );
break;
default:
break;
}
}
// Add zones outlines having an higher priority and keepout
for( int ii = 0; ii < GetBoard()->GetAreaCount(); ii++ )
{
ZONE_CONTAINER* zone = GetBoard()->GetArea( ii );
if( zone->GetLayer() != GetLayer() )
continue;
if( !zone->GetIsKeepout() && zone->GetPriority() <= GetPriority() )
continue;
if( zone->GetIsKeepout() && ! zone->GetDoNotAllowCopperPour() )
continue;
// A highter priority zone or keepout area is found: remove this area
item_boundingbox = zone->GetBoundingBox();
if( !item_boundingbox.Intersects( zone_boundingbox ) )
continue;
// Add the zone outline area.
// However if the zone has the same net as the current zone,
// do not add any clearance.
// the zone will be connected to the current zone, but filled areas
// will use different parameters (clearance, thermal shapes )
bool same_net = GetNetCode() == zone->GetNetCode();
bool use_net_clearance = true;
int min_clearance = zone_clearance;
// Do not forget to make room to draw the thick outlines
// of the hole created by the area of the zone to remove
int holeclearance = zone->GetClearance() + outline_half_thickness;
// The final clearance is obviously the max value of each zone clearance
min_clearance = std::max( min_clearance, holeclearance );
if( zone->GetIsKeepout() || same_net )
{
// Just take in account the fact the outline has a thickness, so
// the actual area to substract is inflated to take in account this fact
min_clearance = outline_half_thickness;
use_net_clearance = false;
}
zone->TransformOutlinesShapeWithClearanceToPolygon(
aFeatures,
min_clearance, use_net_clearance );
}
// Remove thermal symbols
for( MODULE* module = aPcb->m_Modules; module; module = module->Next() )
{
for( D_PAD* pad = module->Pads(); pad != NULL; pad = pad->Next() )
{
// Rejects non-standard pads with tht-only thermal reliefs
if( GetPadConnection( pad ) == PAD_ZONE_CONN_THT_THERMAL
&& pad->GetAttribute() != PAD_ATTRIB_STANDARD )
continue;
if( GetPadConnection( pad ) != PAD_ZONE_CONN_THERMAL
&& GetPadConnection( pad ) != PAD_ZONE_CONN_THT_THERMAL )
continue;
if( !pad->IsOnLayer( GetLayer() ) )
continue;
if( pad->GetNetCode() != GetNetCode() )
continue;
item_boundingbox = pad->GetBoundingBox();
int thermalGap = GetThermalReliefGap( pad );
item_boundingbox.Inflate( thermalGap, thermalGap );
if( item_boundingbox.Intersects( zone_boundingbox ) )
{
CreateThermalReliefPadPolygon( aFeatures,
*pad, thermalGap,
GetThermalReliefCopperBridge( pad ),
m_ZoneMinThickness,
segsPerCircle,
correctionFactor, s_thermalRot );
}
}
}
}
/*
* Note 1: polygons are drawm using outlines witk a thickness = aMinThicknessValue
* so shapes must take in account this outline thickness
*
* Note 2:
* Trapezoidal pads are not considered here because they are very special case
* and are used in microwave applications and they *DO NOT* have a thermal relief that
* change the shape by creating stubs and destroy their properties.
*/
void CreateThermalReliefPadPolygon( SHAPE_POLY_SET& aCornerBuffer,
const D_PAD& aPad,
int aThermalGap,
int aCopperThickness,
int aMinThicknessValue,
int aError,
double aThermalRot )
{
wxPoint corner, corner_end;
wxSize copper_thickness;
wxPoint padShapePos = aPad.ShapePos(); // Note: for pad having a shape offset,
// the pad position is NOT the shape position
/* Keep in account the polygon outline thickness
* aThermalGap must be increased by aMinThicknessValue/2 because drawing external outline
* with a thickness of aMinThicknessValue will reduce gap by aMinThicknessValue/2
*/
aThermalGap += aMinThicknessValue / 2;
/* Keep in account the polygon outline thickness
* copper_thickness must be decreased by aMinThicknessValue because drawing outlines
* with a thickness of aMinThicknessValue will increase real thickness by aMinThicknessValue
*/
int dx = aPad.GetSize().x / 2;
int dy = aPad.GetSize().y / 2;
copper_thickness.x = std::min( aPad.GetSize().x, aCopperThickness ) - aMinThicknessValue;
copper_thickness.y = std::min( aPad.GetSize().y, aCopperThickness ) - aMinThicknessValue;
if( copper_thickness.x < 0 )
copper_thickness.x = 0;
if( copper_thickness.y < 0 )
copper_thickness.y = 0;
switch( aPad.GetShape() )
{
case PAD_SHAPE_CIRCLE: // Add 4 similar holes
{
/* we create 4 copper holes and put them in position 1, 2, 3 and 4
* here is the area of the rectangular pad + its thermal gap
* the 4 copper holes remove the copper in order to create the thermal gap
* 4 ------ 1
* | |
* | |
* | |
* | |
* 3 ------ 2
* holes 2, 3, 4 are the same as hole 1, rotated 90, 180, 270 deg
*/
// Build the hole pattern, for the hole in the X >0, Y > 0 plane:
// The pattern roughtly is a 90 deg arc pie
std::vector <wxPoint> corners_buffer;
int numSegs = std::max( GetArcToSegmentCount( dx + aThermalGap, aError, 360.0 ), 6 );
double correction = GetCircletoPolyCorrectionFactor( numSegs );
double delta = 3600.0 / numSegs;
// Radius of outer arcs of the shape corrected for arc approximation by lines
int outer_radius = KiROUND( ( dx + aThermalGap ) * correction );
// Crosspoint of thermal spoke sides, the first point of polygon buffer
corners_buffer.push_back( wxPoint( copper_thickness.x / 2, copper_thickness.y / 2 ) );
// Add an intermediate point on spoke sides, to allow a > 90 deg angle between side
// and first seg of arc approx
corner.x = copper_thickness.x / 2;
int y = outer_radius - (aThermalGap / 4);
corner.y = KiROUND( sqrt( ( (double) y * y - (double) corner.x * corner.x ) ) );
if( aThermalRot != 0 )
corners_buffer.push_back( corner );
// calculate the starting point of the outter arc
corner.x = copper_thickness.x / 2;
corner.y = KiROUND( sqrt( ( (double) outer_radius * outer_radius ) -
( (double) corner.x * corner.x ) ) );
RotatePoint( &corner, 90 ); // 9 degrees is the spoke fillet size
// calculate the ending point of the outer arc
corner_end.x = corner.y;
corner_end.y = corner.x;
// calculate intermediate points (y coordinate from corner.y to corner_end.y
while( (corner.y > corner_end.y) && (corner.x < corner_end.x) )
{
corners_buffer.push_back( corner );
RotatePoint( &corner, delta );
}
corners_buffer.push_back( corner_end );
/* add an intermediate point, to avoid angles < 90 deg between last arc approx line
* and radius line
*/
corner.x = corners_buffer[1].y;
corner.y = corners_buffer[1].x;
corners_buffer.push_back( corner );
// Now, add the 4 holes ( each is the pattern, rotated by 0, 90, 180 and 270 deg
// aThermalRot = 450 (45.0 degrees orientation) work fine.
double angle_pad = aPad.GetOrientation(); // Pad orientation
double th_angle = aThermalRot;
for( unsigned ihole = 0; ihole < 4; ihole++ )
{
aCornerBuffer.NewOutline();
for( unsigned ii = 0; ii < corners_buffer.size(); ii++ )
{
corner = corners_buffer[ii];
RotatePoint( &corner, th_angle + angle_pad ); // Rotate by segment angle and pad orientation
corner += padShapePos;
aCornerBuffer.Append( corner.x, corner.y );
}
th_angle += 900; // Note: th_angle in in 0.1 deg.
}
}
break;
case PAD_SHAPE_OVAL:
{
// Oval pad support along the lines of round and rectangular pads
std::vector <wxPoint> corners_buffer; // Polygon buffer as vector
dx = (aPad.GetSize().x / 2) + aThermalGap; // Cutout radius x
dy = (aPad.GetSize().y / 2) + aThermalGap; // Cutout radius y
wxPoint shape_offset;
// We want to calculate an oval shape with dx > dy.
// if this is not the case, exchange dx and dy, and rotate the shape 90 deg.
int supp_angle = 0;
if( dx < dy )
{
std::swap( dx, dy );
supp_angle = 900;
std::swap( copper_thickness.x, copper_thickness.y );
}
int deltasize = dx - dy; // = distance between shape position and the 2 demi-circle ends centre
// here we have dx > dy
// Radius of outer arcs of the shape:
int outer_radius = dy; // The radius of the outer arc is radius end + aThermalGap
int numSegs = std::max( GetArcToSegmentCount( outer_radius, aError, 360.0 ), 6 );
double delta = 3600.0 / numSegs;
// Some coordinate fiddling, depending on the shape offset direction
shape_offset = wxPoint( deltasize, 0 );
// Crosspoint of thermal spoke sides, the first point of polygon buffer
corner.x = copper_thickness.x / 2;
corner.y = copper_thickness.y / 2;
corners_buffer.push_back( corner );
// Arc start point calculation, the intersecting point of cutout arc and thermal spoke edge
// If copper thickness is more than shape offset, we need to calculate arc intercept point.
if( copper_thickness.x > deltasize )
{
corner.x = copper_thickness.x / 2;
corner.y = KiROUND( sqrt( ( (double) outer_radius * outer_radius ) -
( (double) ( corner.x - delta ) * ( corner.x - deltasize ) ) ) );
corner.x -= deltasize;
/* creates an intermediate point, to have a > 90 deg angle
* between the side and the first segment of arc approximation
*/
wxPoint intpoint = corner;
intpoint.y -= aThermalGap / 4;
corners_buffer.push_back( intpoint + shape_offset );
RotatePoint( &corner, 90 ); // 9 degrees of thermal fillet
}
else
{
corner.x = copper_thickness.x / 2;
corner.y = outer_radius;
corners_buffer.push_back( corner );
}
// Add an intermediate point on spoke sides, to allow a > 90 deg angle between side
// and first seg of arc approx
wxPoint last_corner;
last_corner.y = copper_thickness.y / 2;
int px = outer_radius - (aThermalGap / 4);
last_corner.x =
KiROUND( sqrt( ( ( (double) px * px ) - (double) last_corner.y * last_corner.y ) ) );
// Arc stop point calculation, the intersecting point of cutout arc and thermal spoke edge
corner_end.y = copper_thickness.y / 2;
corner_end.x =
KiROUND( sqrt( ( (double) outer_radius *
outer_radius ) - ( (double) corner_end.y * corner_end.y ) ) );
RotatePoint( &corner_end, -90 ); // 9 degrees of thermal fillet
// calculate intermediate arc points till limit is reached
while( (corner.y > corner_end.y) && (corner.x < corner_end.x) )
{
corners_buffer.push_back( corner + shape_offset );
RotatePoint( &corner, delta );
}
//corners_buffer.push_back(corner + shape_offset); // TODO: about one mil geometry error forms somewhere.
corners_buffer.push_back( corner_end + shape_offset );
corners_buffer.push_back( last_corner + shape_offset ); // Enabling the line above shows intersection point.
/* Create 2 holes, rotated by pad rotation.
*/
double angle = aPad.GetOrientation() + supp_angle;
for( int irect = 0; irect < 2; irect++ )
{
aCornerBuffer.NewOutline();
for( unsigned ic = 0; ic < corners_buffer.size(); ic++ )
{
wxPoint cpos = corners_buffer[ic];
RotatePoint( &cpos, angle );
cpos += padShapePos;
aCornerBuffer.Append( cpos.x, cpos.y );
}
angle = AddAngles( angle, 1800 ); // this is calculate hole 3
}
// Create holes, that are the mirrored from the previous holes
for( unsigned ic = 0; ic < corners_buffer.size(); ic++ )
{
wxPoint swap = corners_buffer[ic];
swap.x = -swap.x;
corners_buffer[ic] = swap;
}
// Now add corner 4 and 2 (2 is the corner 4 rotated by 180 deg
angle = aPad.GetOrientation() + supp_angle;
for( int irect = 0; irect < 2; irect++ )
{
aCornerBuffer.NewOutline();
for( unsigned ic = 0; ic < corners_buffer.size(); ic++ )
{
wxPoint cpos = corners_buffer[ic];
RotatePoint( &cpos, angle );
cpos += padShapePos;
aCornerBuffer.Append( cpos.x, cpos.y );
}
angle = AddAngles( angle, 1800 );
}
}
break;
case PAD_SHAPE_CHAMFERED_RECT:
case PAD_SHAPE_ROUNDRECT: // thermal shape is the same for rectangular shapes.
case PAD_SHAPE_RECT:
{
/* we create 4 copper holes and put them in position 1, 2, 3 and 4
* here is the area of the rectangular pad + its thermal gap
* the 4 copper holes remove the copper in order to create the thermal gap
* 1 ------ 4
* | |
* | |
* | |
* | |
* 2 ------ 3
* hole 3 is the same as hole 1, rotated 180 deg
* hole 4 is the same as hole 2, rotated 180 deg and is the same as hole 1, mirrored
*/
// First, create a rectangular hole for position 1 :
// 2 ------- 3
// | |
// | |
// | |
// 1 -------4
// Modified rectangles with one corner rounded. TODO: merging with oval thermals
// and possibly round too.
std::vector <wxPoint> corners_buffer; // Polygon buffer as vector
dx = (aPad.GetSize().x / 2) + aThermalGap; // Cutout radius x
dy = (aPad.GetSize().y / 2) + aThermalGap; // Cutout radius y
// calculation is optimized for pad shape with dy >= dx (vertical rectangle).
// if it is not the case, just rotate this shape 90 degrees:
double angle = aPad.GetOrientation();
wxPoint corner_origin_pos( -aPad.GetSize().x / 2, -aPad.GetSize().y / 2 );
if( dy < dx )
{
std::swap( dx, dy );
std::swap( copper_thickness.x, copper_thickness.y );
std::swap( corner_origin_pos.x, corner_origin_pos.y );
angle += 900.0;
}
// Now calculate the hole pattern in position 1 ( top left pad corner )
// The first point of polygon buffer is left lower corner, second the crosspoint of
// thermal spoke sides, the third is upper right corner and the rest are rounding
// vertices going anticlockwise. Note the inverted Y-axis in corners_buffer y coordinates.
wxPoint arc_end_point( -dx, -(aThermalGap / 4 + copper_thickness.y / 2) );
corners_buffer.push_back( arc_end_point ); // Adds small miters to zone
corners_buffer.push_back( wxPoint( -(dx - aThermalGap / 4), -copper_thickness.y / 2 ) ); // fill and spoke corner
corners_buffer.push_back( wxPoint( -copper_thickness.x / 2, -copper_thickness.y / 2 ) );
corners_buffer.push_back( wxPoint( -copper_thickness.x / 2, -(dy - aThermalGap / 4) ) );
// The first point to build the rounded corner:
wxPoint arc_start_point( -(aThermalGap / 4 + copper_thickness.x / 2) , -dy );
corners_buffer.push_back( arc_start_point );
int numSegs = std::max( GetArcToSegmentCount( aThermalGap, aError, 360.0 ), 6 );
double correction = GetCircletoPolyCorrectionFactor( numSegs );
int rounding_radius = KiROUND( aThermalGap * correction ); // Corner rounding radius
// Calculate arc angle parameters.
// the start angle id near 900 decidegrees, the final angle is near 1800.0 decidegrees.
double arc_increment = 3600.0 / numSegs;
// the arc_angle_start is 900.0 or slighly more, depending on the actual arc starting point
double arc_angle_start = atan2( -arc_start_point.y -corner_origin_pos.y, arc_start_point.x - corner_origin_pos.x ) * 1800/M_PI;
if( arc_angle_start < 900.0 )
arc_angle_start = 900.0;
bool first_point = true;
for( double curr_angle = arc_angle_start; ; curr_angle += arc_increment )
{
wxPoint corner_position = wxPoint( rounding_radius, 0 );
RotatePoint( &corner_position, curr_angle ); // Rounding vector rotation
corner_position += corner_origin_pos; // Rounding vector + Pad corner offset
// The arc angle is <= 90 degrees, therefore the arc is finished if the x coordinate
// decrease or the y coordinate is smaller than the y end point
if( !first_point &&
( corner_position.x >= corners_buffer.back().x || corner_position.y > arc_end_point.y ) )
break;
first_point = false;
// Note: for hole in position 1, arc x coordinate is always < x starting point
// and arc y coordinate is always <= y ending point
if( corner_position != corners_buffer.back() // avoid duplicate corners.
&& corner_position.x <= arc_start_point.x ) // skip current point at the right of the starting point
corners_buffer.push_back( corner_position );
}
for( int irect = 0; irect < 2; irect++ )
{
aCornerBuffer.NewOutline();
for( unsigned ic = 0; ic < corners_buffer.size(); ic++ )
{
wxPoint cpos = corners_buffer[ic];
RotatePoint( &cpos, angle ); // Rotate according to module orientation
cpos += padShapePos; // Shift origin to position
aCornerBuffer.Append( cpos.x, cpos.y );
}
angle = AddAngles( angle, 1800 ); // this is calculate hole 3
}
// Create holes, that are the mirrored from the previous holes
for( unsigned ic = 0; ic < corners_buffer.size(); ic++ )
{
wxPoint swap = corners_buffer[ic];
swap.x = -swap.x;
corners_buffer[ic] = swap;
}
// Now add corner 4 and 2 (2 is the corner 4 rotated by 180 deg
for( int irect = 0; irect < 2; irect++ )
{
aCornerBuffer.NewOutline();
for( unsigned ic = 0; ic < corners_buffer.size(); ic++ )
{
wxPoint cpos = corners_buffer[ic];
RotatePoint( &cpos, angle );
cpos += padShapePos;
aCornerBuffer.Append( cpos.x, cpos.y );
}
angle = AddAngles( angle, 1800 );
}
}
break;
case PAD_SHAPE_TRAPEZOID:
{
SHAPE_POLY_SET antipad; // The full antipad area
// We need a length to build the stubs of the thermal reliefs
// the value is not very important. The pad bounding box gives a reasonable value
EDA_RECT bbox = aPad.GetBoundingBox();
int stub_len = std::max( bbox.GetWidth(), bbox.GetHeight() );
aPad.TransformShapeWithClearanceToPolygon( antipad, aThermalGap );
SHAPE_POLY_SET stub; // A basic stub ( a rectangle)
SHAPE_POLY_SET stubs; // the full stubs shape
// We now substract the stubs (connections to the copper zone)
//ClipperLib::Clipper clip_engine;
// Prepare a clipping transform
//clip_engine.AddPath( antipad, ClipperLib::ptSubject, true );
// Create stubs and add them to clipper engine
wxPoint stubBuffer[4];
stubBuffer[0].x = stub_len;
stubBuffer[0].y = copper_thickness.y/2;
stubBuffer[1] = stubBuffer[0];
stubBuffer[1].y = -copper_thickness.y/2;
stubBuffer[2] = stubBuffer[1];
stubBuffer[2].x = -stub_len;
stubBuffer[3] = stubBuffer[2];
stubBuffer[3].y = copper_thickness.y/2;
stub.NewOutline();
for( unsigned ii = 0; ii < arrayDim( stubBuffer ); ii++ )
{
wxPoint cpos = stubBuffer[ii];
RotatePoint( &cpos, aPad.GetOrientation() );
cpos += padShapePos;
stub.Append( cpos.x, cpos.y );
}
stubs.Append( stub );
stubBuffer[0].y = stub_len;
stubBuffer[0].x = copper_thickness.x/2;
stubBuffer[1] = stubBuffer[0];
stubBuffer[1].x = -copper_thickness.x/2;
stubBuffer[2] = stubBuffer[1];
stubBuffer[2].y = -stub_len;
stubBuffer[3] = stubBuffer[2];
stubBuffer[3].x = copper_thickness.x/2;
stub.RemoveAllContours();
stub.NewOutline();
for( unsigned ii = 0; ii < arrayDim( stubBuffer ); ii++ )
{
wxPoint cpos = stubBuffer[ii];
RotatePoint( &cpos, aPad.GetOrientation() );
cpos += padShapePos;
stub.Append( cpos.x, cpos.y );
}
stubs.Append( stub );
stubs.Simplify( SHAPE_POLY_SET::PM_FAST );
antipad.BooleanSubtract( stubs, SHAPE_POLY_SET::PM_FAST );
aCornerBuffer.Append( antipad );
break;
}
default:
;
}
}
void ZONE_FILLER::buildZoneFeatureHoleList( const ZONE_CONTAINER* aZone,
SHAPE_POLY_SET& aFeatures ) const
{
int segsPerCircle;
double correctionFactor;
// Set the number of segments in arc approximations
if( aZone->GetArcSegmentCount() == ARC_APPROX_SEGMENTS_COUNT_HIGHT_DEF )
segsPerCircle = ARC_APPROX_SEGMENTS_COUNT_HIGHT_DEF;
else
segsPerCircle = ARC_APPROX_SEGMENTS_COUNT_LOW_DEF;
/* calculates the coeff to compensate radius reduction of holes clearance
* due to the segment approx.
* For a circle the min radius is radius * cos( 2PI / s_CircleToSegmentsCount / 2)
* s_Correction is 1 /cos( PI/s_CircleToSegmentsCount )
*/
correctionFactor = 1.0 / cos( M_PI / (double) segsPerCircle );
aFeatures.RemoveAllContours();
int outline_half_thickness = aZone->GetMinThickness() / 2;
// When removing holes, the holes must be expanded by outline_half_thickness
// to take in account the thickness of the zone outlines
int zone_clearance = aZone->GetClearance() + outline_half_thickness;
// When holes are created by non copper items (edge cut items), use only
// the m_ZoneClearance parameter (zone clearance with no netclass clearance)
int zone_to_edgecut_clearance = aZone->GetZoneClearance() + outline_half_thickness;
/* store holes (i.e. tracks and pads areas as polygons outlines)
* in a polygon list
*/
/* items ouside the zone bounding box are skipped
* the bounding box is the zone bounding box + the biggest clearance found in Netclass list
*/
EDA_RECT item_boundingbox;
EDA_RECT zone_boundingbox = aZone->GetBoundingBox();
int biggest_clearance = m_board->GetDesignSettings().GetBiggestClearanceValue();
biggest_clearance = std::max( biggest_clearance, zone_clearance );
zone_boundingbox.Inflate( biggest_clearance );
/*
* First : Add pads. Note: pads having the same net as zone are left in zone.
* Thermal shapes will be created later if necessary
*/
/* Use a dummy pad to calculate hole clearance when a pad is not on all copper layers
* and this pad has a hole
* This dummy pad has the size and shape of the hole
* Therefore, this dummy pad is a circle or an oval.
* A pad must have a parent because some functions expect a non null parent
* to find the parent board, and some other data
*/
MODULE dummymodule( m_board ); // Creates a dummy parent
D_PAD dummypad( &dummymodule );
for( MODULE* module = m_board->m_Modules; module; module = module->Next() )
{
D_PAD* nextpad;
for( D_PAD* pad = module->PadsList(); pad != NULL; pad = nextpad )
{
nextpad = pad->Next(); // pad pointer can be modified by next code, so
// calculate the next pad here
if( !pad->IsOnLayer( aZone->GetLayer() ) )
{
/* Test for pads that are on top or bottom only and have a hole.
* There are curious pads but they can be used for some components that are
* inside the board (in fact inside the hole. Some photo diodes and Leds are
* like this)
*/
if( pad->GetDrillSize().x == 0 && pad->GetDrillSize().y == 0 )
continue;
// Use a dummy pad to calculate a hole shape that have the same dimension as
// the pad hole
dummypad.SetSize( pad->GetDrillSize() );
dummypad.SetOrientation( pad->GetOrientation() );
dummypad.SetShape( pad->GetDrillShape() == PAD_DRILL_SHAPE_OBLONG ?
PAD_SHAPE_OVAL : PAD_SHAPE_CIRCLE );
dummypad.SetPosition( pad->GetPosition() );
pad = &dummypad;
}
// Note: netcode <=0 means not connected item
if( ( pad->GetNetCode() != aZone->GetNetCode() ) || ( pad->GetNetCode() <= 0 ) )
{
int item_clearance = pad->GetClearance() + outline_half_thickness;
item_boundingbox = pad->GetBoundingBox();
item_boundingbox.Inflate( item_clearance );
if( item_boundingbox.Intersects( zone_boundingbox ) )
{
int clearance = std::max( zone_clearance, item_clearance );
// PAD_SHAPE_CUSTOM can have a specific keepout, to avoid to break the shape
if( pad->GetShape() == PAD_SHAPE_CUSTOM
&& pad->GetCustomShapeInZoneOpt() == CUST_PAD_SHAPE_IN_ZONE_CONVEXHULL )
{
// the pad shape in zone can be its convex hull or
// the shape itself
SHAPE_POLY_SET outline( pad->GetCustomShapeAsPolygon() );
outline.Inflate( KiROUND( clearance * correctionFactor ), segsPerCircle );
pad->CustomShapeAsPolygonToBoardPosition( &outline,
pad->GetPosition(), pad->GetOrientation() );
if( pad->GetCustomShapeInZoneOpt() == CUST_PAD_SHAPE_IN_ZONE_CONVEXHULL )
{
std::vector<wxPoint> convex_hull;
BuildConvexHull( convex_hull, outline );
aFeatures.NewOutline();
for( unsigned ii = 0; ii < convex_hull.size(); ++ii )
aFeatures.Append( convex_hull[ii] );
}
else
aFeatures.Append( outline );
}
else
pad->TransformShapeWithClearanceToPolygon( aFeatures,
clearance,
segsPerCircle,
correctionFactor );
}
continue;
}
// Pads are removed from zone if the setup is PAD_ZONE_CONN_NONE
// or if they have a custom shape, because a thermal relief will break
// the shape
if( aZone->GetPadConnection( pad ) == PAD_ZONE_CONN_NONE
|| pad->GetShape() == PAD_SHAPE_CUSTOM )
{
int gap = zone_clearance;
int thermalGap = aZone->GetThermalReliefGap( pad );
gap = std::max( gap, thermalGap );
item_boundingbox = pad->GetBoundingBox();
item_boundingbox.Inflate( gap );
if( item_boundingbox.Intersects( zone_boundingbox ) )
{
// PAD_SHAPE_CUSTOM has a specific keepout, to avoid to break the shape
// the pad shape in zone can be its convex hull or the shape itself
if( pad->GetShape() == PAD_SHAPE_CUSTOM
&& pad->GetCustomShapeInZoneOpt() == CUST_PAD_SHAPE_IN_ZONE_CONVEXHULL )
{
// the pad shape in zone can be its convex hull or
// the shape itself
SHAPE_POLY_SET outline( pad->GetCustomShapeAsPolygon() );
outline.Inflate( KiROUND( gap * correctionFactor ), segsPerCircle );
pad->CustomShapeAsPolygonToBoardPosition( &outline,
pad->GetPosition(), pad->GetOrientation() );
std::vector<wxPoint> convex_hull;
BuildConvexHull( convex_hull, outline );
aFeatures.NewOutline();
for( unsigned ii = 0; ii < convex_hull.size(); ++ii )
aFeatures.Append( convex_hull[ii] );
}
else
pad->TransformShapeWithClearanceToPolygon( aFeatures,
gap, segsPerCircle, correctionFactor );
}
}
}
}
/* Add holes (i.e. tracks and vias areas as polygons outlines)
* in cornerBufferPolysToSubstract
*/
for( auto track : m_board->Tracks() )
{
if( !track->IsOnLayer( aZone->GetLayer() ) )
continue;
if( track->GetNetCode() == aZone->GetNetCode() && ( aZone->GetNetCode() != 0) )
continue;
int item_clearance = track->GetClearance() + outline_half_thickness;
item_boundingbox = track->GetBoundingBox();
if( item_boundingbox.Intersects( zone_boundingbox ) )
{
int clearance = std::max( zone_clearance, item_clearance );
track->TransformShapeWithClearanceToPolygon( aFeatures,
clearance,
segsPerCircle,
correctionFactor );
}
}
/* Add module edge items that are on copper layers
* Pcbnew allows these items to be on copper layers in microwave applictions
* This is a bad thing, but must be handled here, until a better way is found
*/
for( auto module : m_board->Modules() )
{
for( auto item : module->GraphicalItems() )
{
if( !item->IsOnLayer( aZone->GetLayer() ) && !item->IsOnLayer( Edge_Cuts ) )
continue;
if( item->Type() != PCB_MODULE_EDGE_T )
continue;
item_boundingbox = item->GetBoundingBox();
if( item_boundingbox.Intersects( zone_boundingbox ) )
{
int zclearance = zone_clearance;
if( item->IsOnLayer( Edge_Cuts ) )
// use only the m_ZoneClearance, not the clearance using
// the netclass value, because we do not have a copper item
zclearance = zone_to_edgecut_clearance;
( (EDGE_MODULE*) item )->TransformShapeWithClearanceToPolygon(
aFeatures, zclearance, segsPerCircle, correctionFactor );
}
}
}
// Add graphic items (copper texts) and board edges
// Currently copper texts have no net, so only the zone_clearance
// is used.
for( auto item : m_board->Drawings() )
{
if( item->GetLayer() != aZone->GetLayer() && item->GetLayer() != Edge_Cuts )
continue;
int zclearance = zone_clearance;
if( item->GetLayer() == Edge_Cuts )
// use only the m_ZoneClearance, not the clearance using
// the netclass value, because we do not have a copper item
zclearance = zone_to_edgecut_clearance;
switch( item->Type() )
{
case PCB_LINE_T:
( (DRAWSEGMENT*) item )->TransformShapeWithClearanceToPolygon(
aFeatures,
zclearance, segsPerCircle, correctionFactor );
break;
case PCB_TEXT_T:
( (TEXTE_PCB*) item )->TransformBoundingBoxWithClearanceToPolygon(
aFeatures, zclearance );
break;
default:
break;
}
}
// Add zones outlines having an higher priority and keepout
for( int ii = 0; ii < m_board->GetAreaCount(); ii++ )
{
ZONE_CONTAINER* zone = m_board->GetArea( ii );
// If the zones share no common layers
if( !aZone->CommonLayerExists( zone->GetLayerSet() ) )
continue;
if( !zone->GetIsKeepout() && zone->GetPriority() <= aZone->GetPriority() )
continue;
if( zone->GetIsKeepout() && !zone->GetDoNotAllowCopperPour() )
continue;
// A highter priority zone or keepout area is found: remove this area
item_boundingbox = zone->GetBoundingBox();
if( !item_boundingbox.Intersects( zone_boundingbox ) )
continue;
// Add the zone outline area.
// However if the zone has the same net as the current zone,
// do not add any clearance.
// the zone will be connected to the current zone, but filled areas
// will use different parameters (clearance, thermal shapes )
bool same_net = aZone->GetNetCode() == zone->GetNetCode();
bool use_net_clearance = true;
int min_clearance = zone_clearance;
// Do not forget to make room to draw the thick outlines
// of the hole created by the area of the zone to remove
int holeclearance = zone->GetClearance() + outline_half_thickness;
// The final clearance is obviously the max value of each zone clearance
min_clearance = std::max( min_clearance, holeclearance );
if( zone->GetIsKeepout() || same_net )
{
// Just take in account the fact the outline has a thickness, so
// the actual area to substract is inflated to take in account this fact
min_clearance = outline_half_thickness;
use_net_clearance = false;
}
zone->TransformOutlinesShapeWithClearanceToPolygon(
aFeatures, min_clearance, use_net_clearance );
}
// Remove thermal symbols
for( auto module : m_board->Modules() )
{
for( auto pad : module->Pads() )
{
// Rejects non-standard pads with tht-only thermal reliefs
if( aZone->GetPadConnection( pad ) == PAD_ZONE_CONN_THT_THERMAL
&& pad->GetAttribute() != PAD_ATTRIB_STANDARD )
continue;
if( aZone->GetPadConnection( pad ) != PAD_ZONE_CONN_THERMAL
&& aZone->GetPadConnection( pad ) != PAD_ZONE_CONN_THT_THERMAL )
continue;
if( !pad->IsOnLayer( aZone->GetLayer() ) )
continue;
if( pad->GetNetCode() != aZone->GetNetCode() )
continue;
item_boundingbox = pad->GetBoundingBox();
int thermalGap = aZone->GetThermalReliefGap( pad );
item_boundingbox.Inflate( thermalGap, thermalGap );
if( item_boundingbox.Intersects( zone_boundingbox ) )
{
CreateThermalReliefPadPolygon( aFeatures,
*pad, thermalGap,
aZone->GetThermalReliefCopperBridge( pad ),
aZone->GetMinThickness(),
segsPerCircle,
correctionFactor, s_thermalRot );
}
}
}
}
/**
* Function buildBoard3DAuxLayers
* Called by CreateDrawGL_List()
* Fills the OpenGL GL_ID_BOARD draw list with items
* on aux layers only
*/
void EDA_3D_CANVAS::buildBoard3DAuxLayers( REPORTER* aErrorMessages, REPORTER* aActivity )
{
const int segcountforcircle = 18;
double correctionFactor = 1.0 / cos( M_PI / (segcountforcircle * 2) );
BOARD* pcb = GetBoard();
SHAPE_POLY_SET bufferPolys;
static const LAYER_ID sequence[] = {
Dwgs_User,
Cmts_User,
Eco1_User,
Eco2_User,
Edge_Cuts,
Margin
};
for( LSEQ aux( sequence, sequence+DIM(sequence) ); aux; ++aux )
{
LAYER_ID layer = *aux;
if( !is3DLayerEnabled( layer ) )
continue;
if( aActivity )
aActivity->Report( wxString::Format( _( "Build layer %s" ), LSET::Name( layer ) ) );
bufferPolys.RemoveAllContours();
for( BOARD_ITEM* item = pcb->m_Drawings; item; item = item->Next() )
{
if( !item->IsOnLayer( layer ) )
continue;
switch( item->Type() )
{
case PCB_LINE_T:
( (DRAWSEGMENT*) item )->TransformShapeWithClearanceToPolygon(
bufferPolys, 0, segcountforcircle, correctionFactor );
break;
case PCB_TEXT_T:
( (TEXTE_PCB*) item )->TransformShapeWithClearanceToPolygonSet(
bufferPolys, 0, segcountforcircle, correctionFactor );
break;
default:
break;
}
}
for( MODULE* module = pcb->m_Modules; module; module = module->Next() )
{
module->TransformPadsShapesWithClearanceToPolygon( layer,
bufferPolys,
0,
segcountforcircle,
correctionFactor );
module->TransformGraphicShapesWithClearanceToPolygonSet( layer,
bufferPolys,
0,
segcountforcircle,
correctionFactor );
}
// bufferPolys contains polygons to merge. Many overlaps .
// Calculate merged polygons and remove pads and vias holes
if( bufferPolys.IsEmpty() )
continue;
bufferPolys.Simplify( polygonsCalcMode );
int thickness = GetPrm3DVisu().GetLayerObjectThicknessBIU( layer );
int zpos = GetPrm3DVisu().GetLayerZcoordBIU( layer );
// for Draw3D_SolidHorizontalPolyPolygons,
// zpos it the middle between bottom and top sides.
// However for top layers, zpos should be the bottom layer pos,
// and for bottom layers, zpos should be the top layer pos.
if( Get3DLayer_Z_Orientation( layer ) > 0 )
zpos += thickness/2;
else
zpos -= thickness/2 ;
float zNormal = 1.0f; // When using thickness it will draw first the top and then botton (with z inverted)
// If we are not using thickness, then the znormal must face the layer direction
// because it will draw just one plane
if( !thickness )
zNormal = Get3DLayer_Z_Orientation( layer );
setGLTechLayersColor( layer );
Draw3D_SolidHorizontalPolyPolygons( bufferPolys, zpos,
thickness, GetPrm3DVisu().m_BiuTo3Dunits, false,
zNormal );
}
}
bool DRC_COURTYARD_OVERLAP::RunDRC( BOARD& aBoard ) const
{
wxLogTrace( DRC_COURTYARD_TRACE, "Running DRC: Courtyard" );
// Detects missing (or malformed) footprint courtyard,
// and for footprint with courtyard, courtyards overlap.
wxString msg;
bool success = true;
const DRC_MARKER_FACTORY& marker_factory = GetMarkerFactory();
// Update courtyard polygons, and test for missing courtyard definition:
for( MODULE* footprint = aBoard.m_Modules; footprint; footprint = footprint->Next() )
{
wxPoint pos = footprint->GetPosition();
bool is_ok = footprint->BuildPolyCourtyard();
if( !is_ok && aBoard.GetDesignSettings().m_ProhibitOverlappingCourtyards )
{
auto marker = std::unique_ptr<MARKER_PCB>( marker_factory.NewMarker(
pos, footprint, DRCE_MALFORMED_COURTYARD_IN_FOOTPRINT ) );
HandleMarker( std::move( marker ) );
success = false;
}
if( !aBoard.GetDesignSettings().m_RequireCourtyards )
continue;
if( footprint->GetPolyCourtyardFront().OutlineCount() == 0
&& footprint->GetPolyCourtyardBack().OutlineCount() == 0 && is_ok )
{
auto marker = std::unique_ptr<MARKER_PCB>( marker_factory.NewMarker(
pos, footprint, DRCE_MISSING_COURTYARD_IN_FOOTPRINT ) );
HandleMarker( std::move( marker ) );
success = false;
}
}
if( !aBoard.GetDesignSettings().m_ProhibitOverlappingCourtyards )
return success;
wxLogTrace( DRC_COURTYARD_TRACE, "Checking for courtyard overlap" );
// Now test for overlapping on top layer:
SHAPE_POLY_SET courtyard; // temporary storage of the courtyard of current footprint
for( MODULE* footprint = aBoard.m_Modules; footprint; footprint = footprint->Next() )
{
if( footprint->GetPolyCourtyardFront().OutlineCount() == 0 )
continue; // No courtyard defined
for( MODULE* candidate = footprint->Next(); candidate; candidate = candidate->Next() )
{
if( candidate->GetPolyCourtyardFront().OutlineCount() == 0 )
continue; // No courtyard defined
courtyard.RemoveAllContours();
courtyard.Append( footprint->GetPolyCourtyardFront() );
// Build the common area between footprint and the candidate:
courtyard.BooleanIntersection(
candidate->GetPolyCourtyardFront(), SHAPE_POLY_SET::PM_FAST );
// If no overlap, courtyard is empty (no common area).
// Therefore if a common polygon exists, this is a DRC error
if( courtyard.OutlineCount() )
{
//Overlap between footprint and candidate
VECTOR2I& pos = courtyard.Vertex( 0, 0, -1 );
auto marker = std::unique_ptr<MARKER_PCB>(
marker_factory.NewMarker( wxPoint( pos.x, pos.y ), footprint, candidate,
DRCE_OVERLAPPING_FOOTPRINTS ) );
HandleMarker( std::move( marker ) );
success = false;
}
}
}
// Test for overlapping on bottom layer:
for( MODULE* footprint = aBoard.m_Modules; footprint; footprint = footprint->Next() )
{
if( footprint->GetPolyCourtyardBack().OutlineCount() == 0 )
continue; // No courtyard defined
for( MODULE* candidate = footprint->Next(); candidate; candidate = candidate->Next() )
{
if( candidate->GetPolyCourtyardBack().OutlineCount() == 0 )
continue; // No courtyard defined
courtyard.RemoveAllContours();
courtyard.Append( footprint->GetPolyCourtyardBack() );
// Build the common area between footprint and the candidate:
courtyard.BooleanIntersection(
candidate->GetPolyCourtyardBack(), SHAPE_POLY_SET::PM_FAST );
// If no overlap, courtyard is empty (no common area).
// Therefore if a common polygon exists, this is a DRC error
if( courtyard.OutlineCount() )
{
//Overlap between footprint and candidate
VECTOR2I& pos = courtyard.Vertex( 0, 0, -1 );
auto marker = std::unique_ptr<MARKER_PCB>(
marker_factory.NewMarker( wxPoint( pos.x, pos.y ), footprint, candidate,
DRCE_OVERLAPPING_FOOTPRINTS ) );
HandleMarker( std::move( marker ) );
success = false;
}
}
}
return success;
}
/* Plot outlines of copper, for copper layer
*/
void PlotLayerOutlines( BOARD* aBoard, PLOTTER* aPlotter,
LSET aLayerMask, const PCB_PLOT_PARAMS& aPlotOpt )
{
BRDITEMS_PLOTTER itemplotter( aPlotter, aBoard, aPlotOpt );
itemplotter.SetLayerSet( aLayerMask );
SHAPE_POLY_SET outlines;
for( LSEQ seq = aLayerMask.Seq( plot_seq, DIM( plot_seq ) ); seq; ++seq )
{
LAYER_ID layer = *seq;
outlines.RemoveAllContours();
aBoard->ConvertBrdLayerToPolygonalContours( layer, outlines );
outlines.Simplify();
// Plot outlines
std::vector< wxPoint > cornerList;
// Now we have one or more basic polygons: plot each polygon
for( int ii = 0; ii < outlines.OutlineCount(); ii++ )
{
for(int kk = 0; kk <= outlines.HoleCount (ii); kk++ )
{
cornerList.clear();
const SHAPE_LINE_CHAIN& path = (kk == 0) ? outlines.COutline( ii ) : outlines.CHole( ii, kk - 1 );
for( int jj = 0; jj < path.PointCount(); jj++ )
cornerList.push_back( wxPoint( path.CPoint( jj ).x , path.CPoint( jj ).y ) );
// Ensure the polygon is closed
if( cornerList[0] != cornerList[cornerList.size() - 1] )
cornerList.push_back( cornerList[0] );
aPlotter->PlotPoly( cornerList, NO_FILL );
}
}
// Plot pad holes
if( aPlotOpt.GetDrillMarksType() != PCB_PLOT_PARAMS::NO_DRILL_SHAPE )
{
for( MODULE* module = aBoard->m_Modules; module; module = module->Next() )
{
for( D_PAD* pad = module->Pads(); pad; pad = pad->Next() )
{
wxSize hole = pad->GetDrillSize();
if( hole.x == 0 || hole.y == 0 )
continue;
if( hole.x == hole.y )
aPlotter->Circle( pad->GetPosition(), hole.x, NO_FILL );
else
{
wxPoint drl_start, drl_end;
int width;
pad->GetOblongDrillGeometry( drl_start, drl_end, width );
aPlotter->ThickSegment( pad->GetPosition() + drl_start,
pad->GetPosition() + drl_end, width, SKETCH );
}
}
}
}
// Plot vias holes
for( TRACK* track = aBoard->m_Track; track; track = track->Next() )
{
const VIA* via = dyn_cast<const VIA*>( track );
if( via && via->IsOnLayer( layer ) ) // via holes can be not through holes
{
aPlotter->Circle( via->GetPosition(), via->GetDrillValue(), NO_FILL );
}
}
}
}