}
rv = 0;
out:
return rv;
}
/*
* Configuration table for pins used for same functions on both TWR-K70F120M
* and K70-SOM. The LCD signals are excluded from this tables, because they may
* change depending on the LCD type.
*/
static const struct kinetis_gpio_pin_config common_iomux[] = {
#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
/* E.18 = GPIO (for I2C_SDA) */
{{KINETIS_GPIO_PORT_E, 18}, KINETIS_GPIO_CONFIG_MUX(1)},
/* E.19 = GPIO (for I2C_SCL) */
{{KINETIS_GPIO_PORT_E, 19}, KINETIS_GPIO_CONFIG_MUX(1)},
#endif /* defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE) */
#if defined(CONFIG_USB_EHCI_MXC) || defined(CONFIG_USB_EHCI_MXC_MODULE)
/* A.6 = ULPI_CLK */
{{KINETIS_GPIO_PORT_A, 6}, KINETIS_GPIO_CONFIG_MUX(2)},
/* A.7 = ULPI_DIR */
{{KINETIS_GPIO_PORT_A, 7}, KINETIS_GPIO_CONFIG_MUX(2)},
/* A.8 = ULPI_NXT */
{{KINETIS_GPIO_PORT_A, 8}, KINETIS_GPIO_CONFIG_MUX(2)},
/* A.9 = ULPI_STP */
{{KINETIS_GPIO_PORT_A, 9}, KINETIS_GPIO_CONFIG_MUX(2)},
/* A.10 = ULPI_DATA0 */
{{KINETIS_GPIO_PORT_A, 10}, KINETIS_GPIO_CONFIG_MUX(2)},
* GPIO pin configuration table for TWR-K70F120M
*
* This table does not list all GPIO pins that will be configured. See also
* the code in `gpio_init()` and in the drivers (for example, the UART driver).
*/
static const struct kinetis_gpio_pin_config twr_k70f120m_gpio[] = {
#ifdef CONFIG_MCFFEC
/* A.5 = RMII0_RXER */
/*
* The pull-down resistor is not really necessary here, because this
* pin is always connected to the PHY (it is not connected by default
* on the TWR-K60N512 board.)
*/
{{KINETIS_GPIO_PORT_A, 5}, KINETIS_GPIO_CONFIG_PULLDOWN(4)},
/* A.12 = RMII0_RXD1 */
{{KINETIS_GPIO_PORT_A, 12}, KINETIS_GPIO_CONFIG_MUX(4)},
/* A.13 = RMII0_RXD0 */
{{KINETIS_GPIO_PORT_A, 13}, KINETIS_GPIO_CONFIG_MUX(4)},
/* A.14 = RMII0_CRS_DV */
{{KINETIS_GPIO_PORT_A, 14}, KINETIS_GPIO_CONFIG_MUX(4)},
/* A.15 = RMII0_TXEN */
{{KINETIS_GPIO_PORT_A, 15}, KINETIS_GPIO_CONFIG_MUX(4)},
/* A.16 = RMII0_TXD0 */
{{KINETIS_GPIO_PORT_A, 16}, KINETIS_GPIO_CONFIG_MUX(4)},
/* A.17 = RMII0_TXD1 */
{{KINETIS_GPIO_PORT_A, 17}, KINETIS_GPIO_CONFIG_MUX(4)},
/* B.0 = RMII0_MDIO */
{{KINETIS_GPIO_PORT_B, 0}, KINETIS_GPIO_CONFIG_MUX(4)},
/* B.1 = RMII0_MDC */
{{KINETIS_GPIO_PORT_B, 1}, KINETIS_GPIO_CONFIG_MUX(4)},
#endif /* CONFIG_MCFFEC */
