nbuf_t *
nbuf_rx_allocate( )
{
/* This routine alters shared data. Disable interrupts! */
int old_ipl = asm_set_ipl( 6 );
/* Return a pointer to the next empty Rx Buffer Descriptor */
int i = rx_bd_idx;
/* Check to see if the ring of BDs is full */
if( rx_nbuf[i].status & RX_BD_INUSE )
return NULL;
/* Mark the buffer as in use */
rx_nbuf[i].status |= RX_BD_INUSE;
/* increment the circular index */
rx_bd_idx = ( uint8 ) ( ( rx_bd_idx + 1 ) % NUM_RXBDS );
/* Restore previous IPL */
asm_set_ipl( old_ipl );
return &rx_nbuf[i];
}
nbuf_t *
nbuf_tx_allocate( )
{
/* This routine alters shared data. Disable interrupts! */
int old_ipl = asm_set_ipl( 6 );
/* Return a pointer to the next empty Tx Buffer Descriptor */
int i = tx_bd_idx;
/* Check to see if ring of BDs is full */
if( ( tx_nbuf[i].status & TX_BD_INUSE ) || ( tx_nbuf[i].status & TX_BD_R ) )
return NULL;
/* Mark the buffer as Ready (in use) */
/* FEC must set R bit in transmit routine */
tx_nbuf[i].status |= TX_BD_INUSE;
/* increment the circular index */
tx_bd_idx = ( uint8 ) ( ( tx_bd_idx + 1 ) % NUM_TXBDS );
/* Restore previous IPL */
asm_set_ipl( old_ipl );
return &tx_nbuf[i];
}
void
mcf523xfec_disable( mcf523xfec_if_t * fecif )
{
( void )fecif;
int old_ipl = asm_set_ipl( 7 );
/* Set the Graceful Transmit Stop bit */
MCF_FEC_TCR = ( MCF_FEC_TCR | MCF_FEC_TCR_GTS );
/* Wait for the current transmission to complete */
while( !( MCF_FEC_EIR & MCF_FEC_EIR_GRA ) );
/* Clear the GRA event */
MCF_FEC_EIR = MCF_FEC_EIR_GRA;
/* Disable the FEC */
MCF_FEC_ECR = 0;
/* Disable all FEC interrupts by clearing the IMR register */
MCF_FEC_EIMR = 0;
/* Unconfigure the interrupt controller. */
MCF_INTC0_ICR27 = MCF_INTC0_ICRn_IL( 0 ) | MCF_INTC0_ICRn_IP( 0 );
MCF_INTC0_IMRL |= MCF_INTC0_IMRL_INT_MASK27;
/* Clear the GTS bit so frames can be tranmitted when restarted */
MCF_FEC_TCR = ( MCF_FEC_TCR & ~MCF_FEC_TCR_GTS );
/* Disable I/O pins used by the FEC. */
MCF_GPIO_PAR_FECI2C &= ~( MCF_GPIO_PAR_FECI2C_PAR_EMDC_FEC |
MCF_GPIO_PAR_FECI2C_PAR_EMDIO_FEC );
( void )asm_set_ipl( old_ipl );
}
void
mcf523xfec_enable( mcf523xfec_if_t * fecif )
{
( void )fecif;
int old_ipl = asm_set_ipl( 7 );
/* Configure I/O pins for the FEC. */
MCF_GPIO_PAR_FECI2C = ( MCF_GPIO_PAR_FECI2C_PAR_EMDC_FEC | MCF_GPIO_PAR_FECI2C_PAR_EMDIO_FEC );
/* Allow interrupts by setting IMR register */
MCF_FEC_EIMR = MCF_FEC_EIMR_RXF;
/* Configure the interrupt controller. */
MCF_INTC0_ICR27 = ( MCF_INTC0_ICRn_IL( MCF_FEC_INT_LEVEL ) |
MCF_INTC0_ICRn_IP( MCF_FEC_INT_PRIORITY ) );
MCF_INTC0_IMRL &= ~( MCF_INTC0_IMRL_INT_MASK27 | MCF_INTC0_IMRL_MASKALL );
/* Enable FEC */
MCF_FEC_ECR = MCF_FEC_ECR_ETHER_EN;
/* Indicate that there have been empty receive buffers produced */
MCF_FEC_RDAR = 1;
( void )asm_set_ipl( old_ipl );
}
void
mcf523xfec_reset( mcf523xfec_if_t * fecif )
{
extern void ( *__RAMVEC[] ) ( );
int old_ipl = asm_set_ipl( 7 );
/* Reset the FEC - equivalent to a hard reset */
MCF_FEC_ECR = MCF_FEC_ECR_RESET;
/* Wait for the reset sequence to complete */
while( MCF_FEC_ECR & MCF_FEC_ECR_RESET );
/* Disable all FEC interrupts by clearing the EIMR register */
MCF_FEC_EIMR = 0;
/* Clear any interrupts by setting all bits in the EIR register */
MCF_FEC_EIR = 0xFFFFFFFFUL;
/* Configure Interrupt vectors. */
__RAMVEC[MCF_FEC_VEC_RXF] = mcf523xfec_rx_irq;
/* Set the source address for the controller */
MCF_FEC_PALR =
( fecif->self->addr[0] << 24U ) | ( fecif->self->addr[1] << 16U ) |
( fecif->self->addr[2] << 8U ) | ( fecif->self->addr[3] << 0U );
MCF_FEC_PAUR = ( fecif->self->addr[4] << 24U ) | ( fecif->self->addr[5] << 16U );
/* Initialize the hash table registers */
MCF_FEC_IAUR = 0;
MCF_FEC_IALR = 0;
/* Set Receive Buffer Size */
#if RX_BUFFER_SIZE != 2048
#error "RX_BUFFER_SIZE must be set to 2048 for safe FEC operation."
#endif
MCF_FEC_EMRBR = RX_BUFFER_SIZE - 1;
/* Point to the start of the circular Rx buffer descriptor queue */
MCF_FEC_ERDSR = nbuf_get_start( NBUF_RX );
/* Point to the start of the circular Tx buffer descriptor queue */
MCF_FEC_ETDSR = nbuf_get_start( NBUF_TX );
/* Set the tranceiver interface to MII mode */
MCF_FEC_RCR = MCF_FEC_RCR_MAX_FL( MCF_FEC_MTU ) | MCF_FEC_RCR_MII_MODE;
/* Set MII Speed Control Register for 2.5Mhz */
MCF_FEC_MSCR = MCF_FEC_MSCR_MII_SPEED( FSYS_2 / ( 2UL * 2500000UL ) );
/* Only operate in half-duplex, no heart beat control */
MCF_FEC_TCR = 0;
/* Enable Debug support */
FEC_DEBUG_INIT;
FEC_DEBUG_RX_TIMING( 0 );
FEC_DEBUG_TX_TIMING( 0 );
( void )asm_set_ipl( old_ipl );
}
void
nbuf_tx_release( nbuf_t * pNbuf )
{
/* This routine alters shared data. Disable interrupts! */
int old_ipl = asm_set_ipl( 6 );
/* Mark the buffer as not in use */
pNbuf->status &= ~TX_BD_INUSE;
/* Restore previous IPL */
asm_set_ipl( old_ipl );
}
/**
* Release a tx buffer inside buffer descriptor ring
* @param pointer to buffer
* @return none
*/
void
NBUF_ReadyTx( nbuf_t * pNbuf )
{
/* This routine alters shared data. Disable interrupts! */
uint8 old_ipl = asm_set_ipl( 6 );
/* Mark the buffer as not in use */
pNbuf->status |= TX_BD_R;
/* Restore previous IPL */
asm_set_ipl( old_ipl );
}
/**
* Release a rx buffer for internal processing
* @param pointer to buffer
* @return none
*/
void
NBUF_ReleaseRX( nbuf_t * pNbuf )
{
/* This routine alters shared data. Disable interrupts! */
uint8 old_ipl = asm_set_ipl( 6 );
/* Mark the buffer as empty and not in use */
pNbuf->status |= RX_BD_E;
pNbuf->status &= ~RX_BD_INUSE;
/* Restore previous IPL */
asm_set_ipl( old_ipl );
}
void
mcf5xxx_irq_disable (void)
{
asm_set_ipl(7);
}
void
mcf5xxx_irq_enable (void)
{
asm_set_ipl(0);
}
void
prvvPortExitCritical( )
{
( void )asm_set_ipl( ( uint32 ) uiRegSR );
}
/* ----------------------- Start implementation -----------------------------*/
void
prvvPortEnterCritical( )
{
uiRegSR = asm_set_ipl( 7 );
}
