static void __init ek_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
/* USB Device */
at91_add_device_udc(&ek_udc_data);
/* SPI */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
/* NAND */
ek_add_device_nand();
/* Ethernet */
ek_add_device_macb();
/* Regulators */
ek_add_regulators();
/* MMC */
ek_add_device_mmc();
/* I2C */
at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
/* LEDs */
ek_add_device_gpio_leds();
/* Push Buttons */
ek_add_device_buttons();
/* PCK0 provides MCLK to the WM8731 */
at91_set_B_periph(AT91_PIN_PC1, 0);
/* SSC (for WM8731) */
at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
}
static void __init eco920_board_init(void)
{
/* DBGU on ttyS0. (Rx & Tx only */
at91_register_uart(0, 0, 0);
at91_add_device_serial();
at91_add_device_eth(&eco920_eth_data);
at91_add_device_usbh(&eco920_usbh_data);
at91_add_device_udc(&eco920_udc_data);
at91_add_device_mci(0, &eco920_mci0_data);
platform_device_register(&eco920_flash);
at91_ramc_write(0, AT91_SMC_CSR(7), AT91_SMC_RWHOLD_(1)
| AT91_SMC_RWSETUP_(1)
| AT91_SMC_DBW_8
| AT91_SMC_WSEN
| AT91_SMC_NWS_(15));
at91_set_A_periph(AT91_PIN_PC6, 1);
at91_set_gpio_input(AT91_PIN_PA23, 0);
at91_set_deglitch(AT91_PIN_PA23, 1);
/* Initialization of the Static Memory Controller for Chip Select 3 */
at91_ramc_write(0, AT91_SMC_CSR(3),
AT91_SMC_DBW_16 | /* 16 bit */
AT91_SMC_WSEN |
AT91_SMC_NWS_(5) | /* wait states */
AT91_SMC_TDF_(1) /* float time */
);
at91_add_device_spi(eco920_spi_devices, ARRAY_SIZE(eco920_spi_devices));
/* LEDs */
at91_gpio_leds(eco920_leds, ARRAY_SIZE(eco920_leds));
}
static void __init kb9202_board_init(void)
{
/* Serial */
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
/* USART0 on ttyS1 (Rx & Tx only) */
at91_register_uart(AT91RM9200_ID_US0, 1, 0);
/* USART1 on ttyS2 (Rx & Tx only) - IRDA (optional) */
at91_register_uart(AT91RM9200_ID_US1, 2, 0);
/* USART3 on ttyS3 (Rx, Tx, CTS, RTS) - RS485 (optional) */
at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&kb9202_eth_data);
/* USB Host */
at91_add_device_usbh(&kb9202_usbh_data);
/* USB Device */
at91_add_device_udc(&kb9202_udc_data);
/* MMC */
at91_add_device_mci(0, &kb9202_mci0_data);
/* I2C */
at91_add_device_i2c(NULL, 0);
/* SPI */
at91_add_device_spi(NULL, 0);
/* NAND */
at91_add_device_nand(&kb9202_nand_data);
/* LEDs */
at91_gpio_leds(kb9202_leds, ARRAY_SIZE(kb9202_leds));
}
static void __init yl9200_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&yl9200_eth_data);
/* USB Host */
at91_add_device_usbh(&yl9200_usbh_data);
/* USB Device */
at91_add_device_udc(&yl9200_udc_data);
/* I2C */
at91_add_device_i2c(yl9200_i2c_devices, ARRAY_SIZE(yl9200_i2c_devices));
/* MMC */
at91_add_device_mmc(0, &yl9200_mmc_data);
/* NAND */
at91_add_device_nand(&yl9200_nand_data);
/* NOR Flash */
platform_device_register(&yl9200_flash);
#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
/* SPI */
at91_add_device_spi(yl9200_spi_devices, ARRAY_SIZE(yl9200_spi_devices));
/* Touchscreen */
yl9200_add_device_ts();
#endif
/* LEDs. */
at91_gpio_leds(yl9200_leds, ARRAY_SIZE(yl9200_leds));
/* Push Buttons */
yl9200_add_device_buttons();
/* VGA */
yl9200_add_device_video();
}
static void __init ek_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
/* USB Device */
at91_add_device_udc(&ek_udc_data);
/* SPI */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
/* NAND */
at91_add_device_nand(&ek_nand_data);
/* I2C */
at91_add_device_i2c(NULL, 0);
/* Ethernet */
at91_add_device_eth(&ek_macb_data);
/* MMC */
at91_add_device_mmc(0, &ek_mmc_data);
/* Push Buttons */
ek_add_device_buttons();
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
/* shutdown controller, wakeup button (5 msec low) */
at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW
| AT91_SHDW_RTTWKEN);
}
static void __init ek_board_init(void)
{
/* */
at91_add_device_serial();
/* */
at91_add_device_usbh(&ek_usbh_data);
/* */
at91_add_device_udc(&ek_udc_data);
/* */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
/* */
ek_add_device_nand();
/* */
ek_add_device_macb();
/* */
ek_add_regulators();
/* */
ek_add_device_mmc();
/* */
at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
/* */
ek_add_device_gpio_leds();
/* */
ek_add_device_buttons();
/* */
at91_set_B_periph(AT91_PIN_PC1, 0);
/* */
at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
}
static void __init cap9adk_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&cap9adk_usbh_data);
/* USB HS */
at91_add_device_usba(&cap9adk_usba_udc_data);
/* SPI */
at91_add_device_spi(cap9adk_spi_devices, ARRAY_SIZE(cap9adk_spi_devices));
/* Touchscreen */
cap9adk_add_device_ts();
/* MMC */
at91_add_device_mmc(1, &cap9adk_mmc_data);
/* Ethernet */
at91_add_device_eth(&cap9adk_macb_data);
/* NAND */
cap9adk_add_device_nand();
/* NOR Flash */
cap9adk_add_device_nor();
/* I2C */
at91_add_device_i2c(NULL, 0);
/* LCD Controller */
at91_add_device_lcdc(&cap9adk_lcdc_data);
/* AC97 */
at91_add_device_ac97(&cap9adk_ac97_data);
}
static void __init ek_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
/* USB Device */
at91_add_device_udc(&ek_udc_data);
/* I2C */
at91_add_device_i2c();
/* NAND */
at91_add_device_nand(&ek_nand_data);
/* DM9000 ethernet */
ek_add_device_dm9000();
/* spi0 and mmc/sd share the same PIO pins */
#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
/* SPI */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
/* Touchscreen */
ek_add_device_ts();
#else
/* MMC */
at91_add_device_mmc(0, &ek_mmc_data);
#endif
/* LCD Controller */
at91_add_device_lcdc(&ek_lcdc_data);
/* Push Buttons */
ek_add_device_buttons();
}
static void __init carmeva_board_init(void)
{
/* Serial */
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
| ATMEL_UART_RI);
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&carmeva_eth_data);
/* USB Host */
at91_add_device_usbh(&carmeva_usbh_data);
/* USB Device */
at91_add_device_udc(&carmeva_udc_data);
/* I2C */
at91_add_device_i2c(NULL, 0);
/* SPI */
at91_add_device_spi(carmeva_spi_devices, ARRAY_SIZE(carmeva_spi_devices));
/* Compact Flash */
// at91_add_device_cf(&carmeva_cf_data);
/* MMC */
at91_add_device_mmc(0, &carmeva_mmc_data);
/* LEDs */
at91_gpio_leds(carmeva_leds, ARRAY_SIZE(carmeva_leds));
}
static void __init csb337_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&csb337_eth_data);
/* USB Host */
at91_add_device_usbh(&csb337_usbh_data);
/* USB Device */
at91_add_device_udc(&csb337_udc_data);
/* I2C */
at91_add_device_i2c(csb337_i2c_devices, ARRAY_SIZE(csb337_i2c_devices));
/* Compact Flash */
at91_set_gpio_input(AT91_PIN_PB22, 1); /* IOIS16 */
at91_add_device_cf(&csb337_cf_data);
/* SPI */
at91_add_device_spi(csb337_spi_devices, ARRAY_SIZE(csb337_spi_devices));
/* MMC */
at91_add_device_mmc(0, &csb337_mmc_data);
/* NOR flash */
platform_device_register(&csb_flash);
/* LEDs */
at91_gpio_leds(csb_leds, ARRAY_SIZE(csb_leds));
/* Switches on CSB300 */
csb300_add_device_buttons();
}
static void __init ek_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
/* USB Device */
at91_add_device_udc(&ek_udc_data);
/* SPI */
at91_set_gpio_output(AT91_PIN_PE20, 1); /* select spi0 clock */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
/* Touchscreen */
ek_add_device_ts();
/* MMC */
at91_add_device_mmc(1, &ek_mmc_data);
/* Ethernet */
at91_add_device_eth(&ek_macb_data);
/* NAND */
at91_add_device_nand(&ek_nand_data);
/* I2C */
at91_add_device_i2c(NULL, 0);
/* LCD Controller */
at91_add_device_lcdc(&ek_lcdc_data);
/* Push Buttons */
ek_add_device_buttons();
/* AC97 */
at91_add_device_ac97(&ek_ac97_data);
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
/* shutdown controller, wakeup button (5 msec low) */
at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW
| AT91_SHDW_RTTWKEN);
}
static void __init pcontrol_g20_board_init(void)
{
/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) piggyback A2 */
at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS
| ATMEL_UART_RTS);
/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) isolated RS485 X5 */
at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS
| ATMEL_UART_RTS);
/* USART2 on ttyS3. (Rx, Tx) 9bit-Bus Multidrop-mode X4 */
at91_register_uart(AT91SAM9260_ID_US4, 3, 0);
stamp9g20_board_init();
at91_add_device_usbh(&usbh_data);
at91_add_device_eth(&macb_data);
at91_add_device_i2c(pcontrol_g20_i2c_devices,
ARRAY_SIZE(pcontrol_g20_i2c_devices));
add_device_pcontrol();
at91_add_device_spi(pcontrol_g20_spi_devices,
ARRAY_SIZE(pcontrol_g20_spi_devices));
at91_add_device_udc(&pcontrol_g20_udc_data);
at91_gpio_leds(pcontrol_g20_leds,
ARRAY_SIZE(pcontrol_g20_leds));
/* piggyback A2 */
at91_set_gpio_output(AT91_PIN_PB31, 1);
}
static void __init ecb_at91board_init(void)
{
/* Serial */
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
/* USART0 on ttyS1. (Rx & Tx only) */
at91_register_uart(AT91RM9200_ID_US0, 1, 0);
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&ecb_at91eth_data);
/* USB Host */
at91_add_device_usbh(&ecb_at91usbh_data);
/* I2C */
at91_add_device_i2c(NULL, 0);
/* MMC */
at91_add_device_mci(0, &ecbat91_mci0_data);
/* SPI */
at91_add_device_spi(ecb_at91spi_devices, ARRAY_SIZE(ecb_at91spi_devices));
/* LEDs */
at91_gpio_leds(ecb_leds, ARRAY_SIZE(ecb_leds));
}
static void __init homematic_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&homematic_eth_data);
/* USB Host */
at91_add_device_usbh(&homematic_usbh_data);
/* USB Device */
at91_add_device_udc(&homematic_udc_data);
at91_set_multi_drive(homematic_udc_data.pullup_pin, 1); /* pullup_pin is connected to reset */
/* I2C */
at91_add_device_i2c(NULL, 0);
/* SPI */
at91_add_device_spi(homematic_spi_devices, ARRAY_SIZE(homematic_spi_devices));
#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
/* DataFlash card */
at91_set_gpio_output(AT91_PIN_PB7, 0);
#else
/* MMC */
at91_set_gpio_output(AT91_PIN_PB7, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */
at91_add_device_mmc(0, &homematic_mmc_data);
#endif
/* NAND */
at91_add_device_nand(&homematic_nand_data);
}
static void __init ek_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&ek_eth_data);
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
/* USB Device */
at91_add_device_udc(&ek_udc_data);
at91_set_multi_drive(ek_udc_data.pullup_pin, 1); /* pullup_pin is connected to reset */
/* I2C */
at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
/* SPI */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
/* DataFlash card */
at91_set_gpio_output(AT91_PIN_PB22, 0);
#else
/* MMC */
at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */
at91_add_device_mmc(0, &ek_mmc_data);
#endif
/* NOR Flash */
platform_device_register(&ek_flash);
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
/* VGA */
// ek_add_device_video();
}
static void __init afeb9260_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&afeb9260_usbh_data);
/* USB Device */
at91_add_device_udc(&afeb9260_udc_data);
/* SPI */
at91_add_device_spi(afeb9260_spi_devices,
ARRAY_SIZE(afeb9260_spi_devices));
/* NAND */
at91_add_device_nand(&afeb9260_nand_data);
/* Ethernet */
at91_add_device_eth(&afeb9260_macb_data);
/* Standard function's pin assignments are not
* appropriate for us and generic code provide
* no API to configure these pins any other way */
at91_set_B_periph(AT91_PIN_PA10, 0); /* ETX2 */
at91_set_B_periph(AT91_PIN_PA11, 0); /* ETX3 */
/* MMC */
at91_add_device_mmc(0, &afeb9260_mmc_data);
/* I2C */
at91_add_device_i2c(afeb9260_i2c_devices,
ARRAY_SIZE(afeb9260_i2c_devices));
/* Audio */
at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
}
static void __init ek_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
/* USB Device */
at91_add_device_udc(&ek_udc_data);
/* SPI */
at91_set_gpio_output(AT91_PIN_PE20, 1); /* select spi0 clock */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
/* Touchscreen */
ek_add_device_ts();
/* MMC */
at91_add_device_mmc(1, &ek_mmc_data);
/* Ethernet */
at91_add_device_eth(&ek_macb_data);
/* NAND */
ek_add_device_nand();
/* I2C */
at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
/* LCD Controller */
at91_add_device_lcdc(&ek_lcdc_data);
/* Push Buttons */
ek_add_device_buttons();
/* AC97 */
at91_add_device_ac97(&ek_ac97_data);
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
at91_pwm_leds(ek_pwm_led, ARRAY_SIZE(ek_pwm_led));
}
static void __init ek_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
/* USB Device */
at91_add_device_udc(&ek_udc_data);
/* I2C */
at91_add_device_i2c(NULL, 0);
/* NAND */
at91_add_device_nand(&ek_nand_data);
/* DM9000 ethernet */
ek_add_device_dm9000();
/* spi0 and mmc/sd share the same PIO pins */
#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
/* SPI */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
/* Touchscreen */
ek_add_device_ts();
/* SSC (to AT73C213) */
at73c213_set_clk(&at73c213_data);
at91_add_device_ssc(AT91SAM9261_ID_SSC1, ATMEL_SSC_TX);
#else
/* MMC */
at91_add_device_mmc(0, &ek_mmc_data);
#endif
/* LCD Controller */
at91_add_device_lcdc(&ek_lcdc_data);
/* Push Buttons */
ek_add_device_buttons();
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
}
static void __init ek_board_init(void)
{
/* Serial */
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
| ATMEL_UART_RI);
/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
/* USB Device */
at91_add_device_udc(&ek_udc_data);
/* SPI */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
/* NAND */
ek_add_device_nand();
/* Ethernet */
at91_add_device_eth(&ek_macb_data);
/* MMC */
at91_add_device_mci(0, &ek_mci0_data);
/* I2C */
at91_add_device_i2c(NULL, 0);
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
}
static void __init ek_board_init(void)
{
at91_add_device_serial();
at91_add_device_usbh(&ek_usbh_data);
at91_add_device_udc(&ek_udc_data);
at91_add_device_i2c(NULL, 0);
ek_add_device_nand();
ek_add_device_dm9000();
#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
ek_add_device_ts();
at73c213_set_clk(&at73c213_data);
at91_add_device_ssc(AT91SAM9261_ID_SSC1, ATMEL_SSC_TX);
#else
at91_add_device_mmc(0, &ek_mmc_data);
#endif
at91_add_device_lcdc(&ek_lcdc_data);
ek_add_device_buttons();
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
}
static void __init foxg20_board_init(void)
{
/* Serial */
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
at91_register_uart(AT91SAM9260_ID_US0, 1,
ATMEL_UART_CTS
| ATMEL_UART_RTS
| ATMEL_UART_DTR
| ATMEL_UART_DSR
| ATMEL_UART_DCD
| ATMEL_UART_RI);
/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
at91_register_uart(AT91SAM9260_ID_US1, 2,
ATMEL_UART_CTS
| ATMEL_UART_RTS);
/* USART2 on ttyS3. (Rx & Tx only) */
at91_register_uart(AT91SAM9260_ID_US2, 3, 0);
/* USART3 on ttyS4. (Rx, Tx, RTS, CTS) */
at91_register_uart(AT91SAM9260_ID_US3, 4,
ATMEL_UART_CTS
| ATMEL_UART_RTS);
/* USART4 on ttyS5. (Rx & Tx only) */
at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
/* USART5 on ttyS6. (Rx & Tx only) */
at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
/* Set the internal pull-up resistor on DRXD */
at91_set_A_periph(AT91_PIN_PB14, 1);
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&foxg20_usbh_data);
/* USB Device */
at91_add_device_udc(&foxg20_udc_data);
/* SPI */
at91_add_device_spi(foxg20_spi_devices, ARRAY_SIZE(foxg20_spi_devices));
/* Ethernet */
at91_add_device_eth(&foxg20_macb_data);
/* MMC */
at91_add_device_mci(0, &foxg20_mci0_data);
/* I2C */
at91_add_device_i2c(foxg20_i2c_devices, ARRAY_SIZE(foxg20_i2c_devices));
/* LEDs */
at91_gpio_leds(foxg20_leds, ARRAY_SIZE(foxg20_leds));
/* Push Buttons */
foxg20_add_device_buttons();
#if defined(CONFIG_W1_MASTER_GPIO) || defined(CONFIG_W1_MASTER_GPIO_MODULE)
at91_add_device_w1();
#endif
}
static void __init csb437tl_board_init(void)
{
/* activate the LED */
at91_set_gpio_direction(LED, 0, 1);
#if (CONFIG_MACH_CSB437TL_REV == 4)
/* power up vcc5 */
at91_set_gpio_direction(AT91_PIN_PB0, 0, 1);
#endif
/* power up USBH ports */
/* TODO: let USBH controller manage USB power */
#if (CONFIG_MACH_CSB437TL_REV == 2)
/* the P2 uses active-low USBHVCC switches */
at91_set_gpio_direction(USBHVCC0, 0, 0);
at91_set_gpio_direction(USBHVCC1, 0, 0);
#else
at91_set_gpio_direction(USBHVCC0, 0, 1);
at91_set_gpio_direction(USBHVCC1, 0, 1);
#endif
#if defined(CONFIG_FB)
{
struct clk *plla, *pck0;
plla = clk_get(NULL, "plla");
pck0 = clk_get(NULL, "pck0");
if (plla && pck0) {
clk_set_rate(plla, 48000000);
clk_set_parent(pck0, plla);
clk_set_rate(pck0, 24000000);
at91_set_A_periph(AT91_PIN_PB27, 0);
}
}
#endif
/* Ethernet */
at91_add_device_eth(&csb437tl_eth_data);
/* USB Host */
at91_add_device_usbh();
/* USB Device */
at91_add_device_udc(&csb437tl_udc_data);
/* Compact Flash */
at91_set_gpio_direction(AT91_PIN_PB22, 1, 1); /* IOIS16 */
at91_add_device_cf(&csb437tl_cf_data);
/* MMC */
at91_add_device_mmc(&csb437tl_mmc_data);
#if defined(CONFIG_FB_VOYAGER_GX)
platform_device_register(&at91_panel_dev);
#endif
platform_device_register(&sm501_8051_dev);
platform_device_register(&ac97_dev);
}
static void __init onearm_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&onearm_eth_data);
/* USB Host */
at91_add_device_usbh(&onearm_usbh_data);
/* USB Device */
at91_add_device_udc(&onearm_udc_data);
}
static void __init onearm_board_init(void)
{
at91_add_device_serial();
at91_add_device_eth(&onearm_eth_data);
at91_add_device_usbh(&onearm_usbh_data);
at91_add_device_udc(&onearm_udc_data);
}
static void __init snapper9260_board_init(void)
{
at91_add_device_i2c(snapper9260_i2c_devices,
ARRAY_SIZE(snapper9260_i2c_devices));
at91_add_device_serial();
at91_add_device_usbh(&snapper9260_usbh_data);
at91_add_device_udc(&snapper9260_udc_data);
at91_add_device_eth(&snapper9260_macb_data);
at91_add_device_ssc(AT91SAM9260_ID_SSC, (ATMEL_SSC_TF | ATMEL_SSC_TK |
ATMEL_SSC_TD | ATMEL_SSC_RD));
snapper9260_add_device_nand();
}
static void __init ek_board_init(void)
{
/* Ethernet */
at91_add_device_eth(&ek_eth_data);
/* USB Host */
at91_add_device_usbh();
/* USB Device */
at91_add_device_udc(&ek_udc_data);
/* MMC */
at91_set_gpio_direction(AT91_PIN_PB22, 0, 1); /* this MMC card slot can optionally use SPI signaling (CS3). default: MMC */
at91_add_device_mmc(&ek_mmc_data);
/* VGA */
ek_add_device_video();
}
static void __init stamp9g20evb_board_init(void)
{
stamp9g20_board_init();
/* */
at91_add_device_usbh(&usbh_data);
/* */
at91_add_device_udc(&stamp9g20evb_udc_data);
/* */
at91_add_device_eth(&macb_data);
/* */
at91_add_device_i2c(NULL, 0);
/* */
at91_gpio_leds(stamp9g20evb_leds, ARRAY_SIZE(stamp9g20evb_leds));
}
static void __init csb337_board_init(void)
{
/* Ethernet */
at91_add_device_eth(&csb337_eth_data);
/* USB Host */
at91_add_device_usbh();
/* USB Device */
at91_add_device_udc(&csb337_udc_data);
/* Compact Flash */
at91_set_gpio_direction(AT91_PIN_PB22, 1, 1); /* IOIS16 */
at91_add_device_cf(&csb337_cf_data);
/* MMC */
at91_add_device_mmc(&csb337_mmc_data);
}
static void __init stamp9g20evb_board_init(void)
{
stamp9g20_board_init();
/* USB Host */
at91_add_device_usbh(&usbh_data);
/* USB Device */
at91_add_device_udc(&stamp9g20evb_udc_data);
/* Ethernet */
at91_add_device_eth(&macb_data);
/* I2C */
at91_add_device_i2c(NULL, 0);
/* LEDs */
at91_gpio_leds(stamp9g20evb_leds, ARRAY_SIZE(stamp9g20evb_leds));
}
static void __init kafa_board_init(void)
{
/* */
at91_add_device_serial();
/* */
at91_add_device_eth(&kafa_eth_data);
/* */
at91_add_device_usbh(&kafa_usbh_data);
/* */
at91_add_device_udc(&kafa_udc_data);
/* */
at91_add_device_i2c(NULL, 0);
/* */
at91_add_device_spi(NULL, 0);
}