Exemplo n.º 1
0
static void __init ek_board_init(void)
{
	/* Serial */
	at91_add_device_serial();
	/* USB Host */
	at91_add_device_usbh(&ek_usbh_data);
	/* USB Device */
	at91_add_device_udc(&ek_udc_data);
	/* SPI */
	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
	/* NAND */
	ek_add_device_nand();
	/* Ethernet */
	ek_add_device_macb();
	/* Regulators */
	ek_add_regulators();
	/* MMC */
	ek_add_device_mmc();
	/* I2C */
	at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
	/* LEDs */
	ek_add_device_gpio_leds();
	/* Push Buttons */
	ek_add_device_buttons();
	/* PCK0 provides MCLK to the WM8731 */
	at91_set_B_periph(AT91_PIN_PC1, 0);
	/* SSC (for WM8731) */
	at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
}
Exemplo n.º 2
0
static void __init eco920_board_init(void)
{
	/* DBGU on ttyS0. (Rx & Tx only */
	at91_register_uart(0, 0, 0);
	at91_add_device_serial();
	at91_add_device_eth(&eco920_eth_data);
	at91_add_device_usbh(&eco920_usbh_data);
	at91_add_device_udc(&eco920_udc_data);

	at91_add_device_mci(0, &eco920_mci0_data);
	platform_device_register(&eco920_flash);

	at91_ramc_write(0, AT91_SMC_CSR(7),	AT91_SMC_RWHOLD_(1)
				| AT91_SMC_RWSETUP_(1)
				| AT91_SMC_DBW_8
				| AT91_SMC_WSEN
				| AT91_SMC_NWS_(15));

	at91_set_A_periph(AT91_PIN_PC6, 1);

	at91_set_gpio_input(AT91_PIN_PA23, 0);
	at91_set_deglitch(AT91_PIN_PA23, 1);

/* Initialization of the Static Memory Controller for Chip Select 3 */
	at91_ramc_write(0, AT91_SMC_CSR(3),
		AT91_SMC_DBW_16  |	/* 16 bit */
		AT91_SMC_WSEN    |
		AT91_SMC_NWS_(5) |	/* wait states */
		AT91_SMC_TDF_(1)	/* float time */
	);

	at91_add_device_spi(eco920_spi_devices, ARRAY_SIZE(eco920_spi_devices));
	/* LEDs */
	at91_gpio_leds(eco920_leds, ARRAY_SIZE(eco920_leds));
}
Exemplo n.º 3
0
static void __init kb9202_board_init(void)
{
	/* Serial */
	/* DBGU on ttyS0. (Rx & Tx only) */
	at91_register_uart(0, 0, 0);

	/* USART0 on ttyS1 (Rx & Tx only) */
	at91_register_uart(AT91RM9200_ID_US0, 1, 0);

	/* USART1 on ttyS2 (Rx & Tx only) - IRDA (optional) */
	at91_register_uart(AT91RM9200_ID_US1, 2, 0);

	/* USART3 on ttyS3 (Rx, Tx, CTS, RTS) - RS485 (optional) */
	at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
	at91_add_device_serial();
	/* Ethernet */
	at91_add_device_eth(&kb9202_eth_data);
	/* USB Host */
	at91_add_device_usbh(&kb9202_usbh_data);
	/* USB Device */
	at91_add_device_udc(&kb9202_udc_data);
	/* MMC */
	at91_add_device_mci(0, &kb9202_mci0_data);
	/* I2C */
	at91_add_device_i2c(NULL, 0);
	/* SPI */
	at91_add_device_spi(NULL, 0);
	/* NAND */
	at91_add_device_nand(&kb9202_nand_data);
	/* LEDs */
	at91_gpio_leds(kb9202_leds, ARRAY_SIZE(kb9202_leds));
}
Exemplo n.º 4
0
static void __init yl9200_board_init(void)
{
	/* Serial */
	at91_add_device_serial();
	/* Ethernet */
	at91_add_device_eth(&yl9200_eth_data);
	/* USB Host */
	at91_add_device_usbh(&yl9200_usbh_data);
	/* USB Device */
	at91_add_device_udc(&yl9200_udc_data);
	/* I2C */
	at91_add_device_i2c(yl9200_i2c_devices, ARRAY_SIZE(yl9200_i2c_devices));
	/* MMC */
	at91_add_device_mmc(0, &yl9200_mmc_data);
	/* NAND */
	at91_add_device_nand(&yl9200_nand_data);
	/* NOR Flash */
	platform_device_register(&yl9200_flash);
#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
	/* SPI */
	at91_add_device_spi(yl9200_spi_devices, ARRAY_SIZE(yl9200_spi_devices));
	/* Touchscreen */
	yl9200_add_device_ts();
#endif
	/* LEDs. */
	at91_gpio_leds(yl9200_leds, ARRAY_SIZE(yl9200_leds));
	/* Push Buttons */
	yl9200_add_device_buttons();
	/* VGA */
	yl9200_add_device_video();
}
Exemplo n.º 5
0
static void __init ek_board_init(void)
{
	/* Serial */
	at91_add_device_serial();
	/* USB Host */
	at91_add_device_usbh(&ek_usbh_data);
	/* USB Device */
	at91_add_device_udc(&ek_udc_data);
	/* SPI */
	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
	/* NAND */
	at91_add_device_nand(&ek_nand_data);
	/* I2C */
	at91_add_device_i2c(NULL, 0);
	/* Ethernet */
	at91_add_device_eth(&ek_macb_data);
	/* MMC */
	at91_add_device_mmc(0, &ek_mmc_data);
	/* Push Buttons */
	ek_add_device_buttons();
	/* LEDs */
	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
	/* shutdown controller, wakeup button (5 msec low) */
	at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW
				| AT91_SHDW_RTTWKEN);
}
static void __init ek_board_init(void)
{
	/*        */
	at91_add_device_serial();
	/*          */
	at91_add_device_usbh(&ek_usbh_data);
	/*            */
	at91_add_device_udc(&ek_udc_data);
	/*     */
	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
	/*      */
	ek_add_device_nand();
	/*          */
	ek_add_device_macb();
	/*            */
	ek_add_regulators();
	/*     */
	ek_add_device_mmc();
	/*     */
	at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
	/*      */
	ek_add_device_gpio_leds();
	/*              */
	ek_add_device_buttons();
	/*                                  */
	at91_set_B_periph(AT91_PIN_PC1, 0);
	/*                  */
	at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
}
Exemplo n.º 7
0
static void __init cap9adk_board_init(void)
{
	/* Serial */
	at91_add_device_serial();
	/* USB Host */
	at91_add_device_usbh(&cap9adk_usbh_data);
	/* USB HS */
	at91_add_device_usba(&cap9adk_usba_udc_data);
	/* SPI */
	at91_add_device_spi(cap9adk_spi_devices, ARRAY_SIZE(cap9adk_spi_devices));
	/* Touchscreen */
	cap9adk_add_device_ts();
	/* MMC */
	at91_add_device_mmc(1, &cap9adk_mmc_data);
	/* Ethernet */
	at91_add_device_eth(&cap9adk_macb_data);
	/* NAND */
	cap9adk_add_device_nand();
	/* NOR Flash */
	cap9adk_add_device_nor();
	/* I2C */
	at91_add_device_i2c(NULL, 0);
	/* LCD Controller */
	at91_add_device_lcdc(&cap9adk_lcdc_data);
	/* AC97 */
	at91_add_device_ac97(&cap9adk_ac97_data);
}
Exemplo n.º 8
0
static void __init ek_board_init(void)
{
	/* Serial */
	at91_add_device_serial();
	/* USB Host */
	at91_add_device_usbh(&ek_usbh_data);
	/* USB Device */
	at91_add_device_udc(&ek_udc_data);
	/* I2C */
	at91_add_device_i2c();
	/* NAND */
	at91_add_device_nand(&ek_nand_data);
	/* DM9000 ethernet */
	ek_add_device_dm9000();

	/* spi0 and mmc/sd share the same PIO pins */
#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
	/* SPI */
	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
	/* Touchscreen */
	ek_add_device_ts();
#else
	/* MMC */
	at91_add_device_mmc(0, &ek_mmc_data);
#endif
	/* LCD Controller */
	at91_add_device_lcdc(&ek_lcdc_data);
	/* Push Buttons */
	ek_add_device_buttons();
}
Exemplo n.º 9
0
static void __init carmeva_board_init(void)
{
	/* Serial */
	/* DBGU on ttyS0. (Rx & Tx only) */
	at91_register_uart(0, 0, 0);

	/* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
	at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
			   | ATMEL_UART_RI);
	at91_add_device_serial();
	/* Ethernet */
	at91_add_device_eth(&carmeva_eth_data);
	/* USB Host */
	at91_add_device_usbh(&carmeva_usbh_data);
	/* USB Device */
	at91_add_device_udc(&carmeva_udc_data);
	/* I2C */
	at91_add_device_i2c(NULL, 0);
	/* SPI */
	at91_add_device_spi(carmeva_spi_devices, ARRAY_SIZE(carmeva_spi_devices));
	/* Compact Flash */
//	at91_add_device_cf(&carmeva_cf_data);
	/* MMC */
	at91_add_device_mmc(0, &carmeva_mmc_data);
	/* LEDs */
	at91_gpio_leds(carmeva_leds, ARRAY_SIZE(carmeva_leds));
}
Exemplo n.º 10
0
static void __init csb337_board_init(void)
{
	/* Serial */
	at91_add_device_serial();
	/* Ethernet */
	at91_add_device_eth(&csb337_eth_data);
	/* USB Host */
	at91_add_device_usbh(&csb337_usbh_data);
	/* USB Device */
	at91_add_device_udc(&csb337_udc_data);
	/* I2C */
	at91_add_device_i2c(csb337_i2c_devices, ARRAY_SIZE(csb337_i2c_devices));
	/* Compact Flash */
	at91_set_gpio_input(AT91_PIN_PB22, 1);		/* IOIS16 */
	at91_add_device_cf(&csb337_cf_data);
	/* SPI */
	at91_add_device_spi(csb337_spi_devices, ARRAY_SIZE(csb337_spi_devices));
	/* MMC */
	at91_add_device_mmc(0, &csb337_mmc_data);
	/* NOR flash */
	platform_device_register(&csb_flash);
	/* LEDs */
	at91_gpio_leds(csb_leds, ARRAY_SIZE(csb_leds));
	/* Switches on CSB300 */
	csb300_add_device_buttons();
}
Exemplo n.º 11
0
static void __init ek_board_init(void)
{
	/* Serial */
	at91_add_device_serial();
	/* USB Host */
	at91_add_device_usbh(&ek_usbh_data);
	/* USB Device */
	at91_add_device_udc(&ek_udc_data);
	/* SPI */
	at91_set_gpio_output(AT91_PIN_PE20, 1);		/* select spi0 clock */
	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
	/* Touchscreen */
	ek_add_device_ts();
	/* MMC */
	at91_add_device_mmc(1, &ek_mmc_data);
	/* Ethernet */
	at91_add_device_eth(&ek_macb_data);
	/* NAND */
	at91_add_device_nand(&ek_nand_data);
	/* I2C */
	at91_add_device_i2c(NULL, 0);
	/* LCD Controller */
	at91_add_device_lcdc(&ek_lcdc_data);
	/* Push Buttons */
	ek_add_device_buttons();
	/* AC97 */
	at91_add_device_ac97(&ek_ac97_data);
	/* LEDs */
	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
	/* shutdown controller, wakeup button (5 msec low) */
	at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW
				| AT91_SHDW_RTTWKEN);
}
Exemplo n.º 12
0
static void __init pcontrol_g20_board_init(void)
{
	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) piggyback  A2 */
	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS
						| ATMEL_UART_RTS);

	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) isolated RS485  X5 */
	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS
						| ATMEL_UART_RTS);

	/* USART2 on ttyS3. (Rx, Tx)  9bit-Bus  Multidrop-mode  X4 */
	at91_register_uart(AT91SAM9260_ID_US4, 3, 0);
	stamp9g20_board_init();
	at91_add_device_usbh(&usbh_data);
	at91_add_device_eth(&macb_data);
	at91_add_device_i2c(pcontrol_g20_i2c_devices,
		ARRAY_SIZE(pcontrol_g20_i2c_devices));
	add_device_pcontrol();
	at91_add_device_spi(pcontrol_g20_spi_devices,
		ARRAY_SIZE(pcontrol_g20_spi_devices));
	at91_add_device_udc(&pcontrol_g20_udc_data);
	at91_gpio_leds(pcontrol_g20_leds,
		ARRAY_SIZE(pcontrol_g20_leds));
	/* piggyback  A2 */
	at91_set_gpio_output(AT91_PIN_PB31, 1);
}
Exemplo n.º 13
0
static void __init ecb_at91board_init(void)
{
	/* Serial */
	/* DBGU on ttyS0. (Rx & Tx only) */
	at91_register_uart(0, 0, 0);

	/* USART0 on ttyS1. (Rx & Tx only) */
	at91_register_uart(AT91RM9200_ID_US0, 1, 0);
	at91_add_device_serial();

	/* Ethernet */
	at91_add_device_eth(&ecb_at91eth_data);

	/* USB Host */
	at91_add_device_usbh(&ecb_at91usbh_data);

	/* I2C */
	at91_add_device_i2c(NULL, 0);

	/* MMC */
	at91_add_device_mci(0, &ecbat91_mci0_data);

	/* SPI */
	at91_add_device_spi(ecb_at91spi_devices, ARRAY_SIZE(ecb_at91spi_devices));

	/* LEDs */
	at91_gpio_leds(ecb_leds, ARRAY_SIZE(ecb_leds));
}
Exemplo n.º 14
0
static void __init homematic_board_init(void)
{
	/* Serial */
	at91_add_device_serial();
	/* Ethernet */
	at91_add_device_eth(&homematic_eth_data);
	/* USB Host */
	at91_add_device_usbh(&homematic_usbh_data);
	/* USB Device */
	at91_add_device_udc(&homematic_udc_data);
	at91_set_multi_drive(homematic_udc_data.pullup_pin, 1);	/* pullup_pin is connected to reset */
	/* I2C */
	at91_add_device_i2c(NULL, 0);
	/* SPI */
	at91_add_device_spi(homematic_spi_devices, ARRAY_SIZE(homematic_spi_devices));
#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
	/* DataFlash card */
	at91_set_gpio_output(AT91_PIN_PB7, 0);
#else
	/* MMC */
	at91_set_gpio_output(AT91_PIN_PB7, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). */
	at91_add_device_mmc(0, &homematic_mmc_data);
#endif
	/* NAND */
	at91_add_device_nand(&homematic_nand_data);
}
Exemplo n.º 15
0
static void __init ek_board_init(void)
{
	/* Serial */
	at91_add_device_serial();
	/* Ethernet */
	at91_add_device_eth(&ek_eth_data);
	/* USB Host */
	at91_add_device_usbh(&ek_usbh_data);
	/* USB Device */
	at91_add_device_udc(&ek_udc_data);
	at91_set_multi_drive(ek_udc_data.pullup_pin, 1);	/* pullup_pin is connected to reset */
	/* I2C */
	at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
	/* SPI */
	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
	/* DataFlash card */
	at91_set_gpio_output(AT91_PIN_PB22, 0);
#else
	/* MMC */
	at91_set_gpio_output(AT91_PIN_PB22, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). */
	at91_add_device_mmc(0, &ek_mmc_data);
#endif
	/* NOR Flash */
	platform_device_register(&ek_flash);
	/* LEDs */
	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
	/* VGA */
//	ek_add_device_video();
}
Exemplo n.º 16
0
static void __init afeb9260_board_init(void)
{
	/* Serial */
	at91_add_device_serial();
	/* USB Host */
	at91_add_device_usbh(&afeb9260_usbh_data);
	/* USB Device */
	at91_add_device_udc(&afeb9260_udc_data);
	/* SPI */
	at91_add_device_spi(afeb9260_spi_devices,
			ARRAY_SIZE(afeb9260_spi_devices));
	/* NAND */
	at91_add_device_nand(&afeb9260_nand_data);
	/* Ethernet */
	at91_add_device_eth(&afeb9260_macb_data);

	/* Standard function's pin assignments are not
	 * appropriate for us and generic code provide
	 * no API to configure these pins any other way */
	at91_set_B_periph(AT91_PIN_PA10, 0);	/* ETX2 */
	at91_set_B_periph(AT91_PIN_PA11, 0);	/* ETX3 */
	/* MMC */
	at91_add_device_mmc(0, &afeb9260_mmc_data);
	/* I2C */
	at91_add_device_i2c(afeb9260_i2c_devices,
			ARRAY_SIZE(afeb9260_i2c_devices));
	/* Audio */
	at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
}
static void __init ek_board_init(void)
{
	/* Serial */
	at91_add_device_serial();
	/* USB Host */
	at91_add_device_usbh(&ek_usbh_data);
	/* USB Device */
	at91_add_device_udc(&ek_udc_data);
	/* SPI */
	at91_set_gpio_output(AT91_PIN_PE20, 1);		/* select spi0 clock */
	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
	/* Touchscreen */
	ek_add_device_ts();
	/* MMC */
	at91_add_device_mmc(1, &ek_mmc_data);
	/* Ethernet */
	at91_add_device_eth(&ek_macb_data);
	/* NAND */
	ek_add_device_nand();
	/* I2C */
	at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
	/* LCD Controller */
	at91_add_device_lcdc(&ek_lcdc_data);
	/* Push Buttons */
	ek_add_device_buttons();
	/* AC97 */
	at91_add_device_ac97(&ek_ac97_data);
	/* LEDs */
	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
	at91_pwm_leds(ek_pwm_led, ARRAY_SIZE(ek_pwm_led));
}
Exemplo n.º 18
0
static void __init ek_board_init(void)
{
	/* Serial */
	at91_add_device_serial();
	/* USB Host */
	at91_add_device_usbh(&ek_usbh_data);
	/* USB Device */
	at91_add_device_udc(&ek_udc_data);
	/* I2C */
	at91_add_device_i2c(NULL, 0);
	/* NAND */
	at91_add_device_nand(&ek_nand_data);
	/* DM9000 ethernet */
	ek_add_device_dm9000();

	/* spi0 and mmc/sd share the same PIO pins */
#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
	/* SPI */
	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
	/* Touchscreen */
	ek_add_device_ts();
	/* SSC (to AT73C213) */
	at73c213_set_clk(&at73c213_data);
	at91_add_device_ssc(AT91SAM9261_ID_SSC1, ATMEL_SSC_TX);
#else
	/* MMC */
	at91_add_device_mmc(0, &ek_mmc_data);
#endif
	/* LCD Controller */
	at91_add_device_lcdc(&ek_lcdc_data);
	/* Push Buttons */
	ek_add_device_buttons();
	/* LEDs */
	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
}
Exemplo n.º 19
0
static void __init ek_board_init(void)
{
	/* Serial */
	/* DBGU on ttyS0. (Rx & Tx only) */
	at91_register_uart(0, 0, 0);

	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
			   | ATMEL_UART_RI);

	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
	at91_add_device_serial();
	/* USB Host */
	at91_add_device_usbh(&ek_usbh_data);
	/* USB Device */
	at91_add_device_udc(&ek_udc_data);
	/* SPI */
	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
	/* NAND */
	ek_add_device_nand();
	/* Ethernet */
	at91_add_device_eth(&ek_macb_data);
	/* MMC */
	at91_add_device_mci(0, &ek_mci0_data);
	/* I2C */
	at91_add_device_i2c(NULL, 0);
	/* LEDs */
	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
}
Exemplo n.º 20
0
static void __init ek_board_init(void)
{
	
	at91_add_device_serial();
	
	at91_add_device_usbh(&ek_usbh_data);
	
	at91_add_device_udc(&ek_udc_data);
	
	at91_add_device_i2c(NULL, 0);
	
	ek_add_device_nand();
	
	ek_add_device_dm9000();

	
#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
	
	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
	
	ek_add_device_ts();
	
	at73c213_set_clk(&at73c213_data);
	at91_add_device_ssc(AT91SAM9261_ID_SSC1, ATMEL_SSC_TX);
#else
	
	at91_add_device_mmc(0, &ek_mmc_data);
#endif
	
	at91_add_device_lcdc(&ek_lcdc_data);
	
	ek_add_device_buttons();
	
	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
}
Exemplo n.º 21
0
static void __init foxg20_board_init(void)
{
	/* Serial */
	/* DBGU on ttyS0. (Rx & Tx only) */
	at91_register_uart(0, 0, 0);

	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
	at91_register_uart(AT91SAM9260_ID_US0, 1,
				ATMEL_UART_CTS
				| ATMEL_UART_RTS
				| ATMEL_UART_DTR
				| ATMEL_UART_DSR
				| ATMEL_UART_DCD
				| ATMEL_UART_RI);

	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
	at91_register_uart(AT91SAM9260_ID_US1, 2,
		ATMEL_UART_CTS
		| ATMEL_UART_RTS);

	/* USART2 on ttyS3. (Rx & Tx only) */
	at91_register_uart(AT91SAM9260_ID_US2, 3, 0);

	/* USART3 on ttyS4. (Rx, Tx, RTS, CTS) */
	at91_register_uart(AT91SAM9260_ID_US3, 4,
		ATMEL_UART_CTS
		| ATMEL_UART_RTS);

	/* USART4 on ttyS5. (Rx & Tx only) */
	at91_register_uart(AT91SAM9260_ID_US4, 5, 0);

	/* USART5 on ttyS6. (Rx & Tx only) */
	at91_register_uart(AT91SAM9260_ID_US5, 6, 0);

	/* Set the internal pull-up resistor on DRXD */
	at91_set_A_periph(AT91_PIN_PB14, 1);
	at91_add_device_serial();
	/* USB Host */
	at91_add_device_usbh(&foxg20_usbh_data);
	/* USB Device */
	at91_add_device_udc(&foxg20_udc_data);
	/* SPI */
	at91_add_device_spi(foxg20_spi_devices, ARRAY_SIZE(foxg20_spi_devices));
	/* Ethernet */
	at91_add_device_eth(&foxg20_macb_data);
	/* MMC */
	at91_add_device_mci(0, &foxg20_mci0_data);
	/* I2C */
	at91_add_device_i2c(foxg20_i2c_devices, ARRAY_SIZE(foxg20_i2c_devices));
	/* LEDs */
	at91_gpio_leds(foxg20_leds, ARRAY_SIZE(foxg20_leds));
	/* Push Buttons */
	foxg20_add_device_buttons();
#if defined(CONFIG_W1_MASTER_GPIO) || defined(CONFIG_W1_MASTER_GPIO_MODULE)
	at91_add_device_w1();
#endif
}
Exemplo n.º 22
0
static void __init csb437tl_board_init(void)
{
        /* activate the LED */
        at91_set_gpio_direction(LED, 0, 1);

#if (CONFIG_MACH_CSB437TL_REV == 4)
        /* power up vcc5 */
        at91_set_gpio_direction(AT91_PIN_PB0, 0, 1);
#endif

        /* power up USBH ports */
        /* TODO: let USBH controller manage USB power */
#if (CONFIG_MACH_CSB437TL_REV == 2)
        /* the P2 uses active-low USBHVCC switches */
        at91_set_gpio_direction(USBHVCC0, 0, 0);
        at91_set_gpio_direction(USBHVCC1, 0, 0);
#else
        at91_set_gpio_direction(USBHVCC0, 0, 1);
        at91_set_gpio_direction(USBHVCC1, 0, 1);
#endif
        
#if defined(CONFIG_FB)
        {
          struct clk *plla, *pck0;
          
          plla = clk_get(NULL, "plla");
          pck0 = clk_get(NULL, "pck0");
          if (plla && pck0) {
            clk_set_rate(plla, 48000000);
            clk_set_parent(pck0, plla);
            clk_set_rate(pck0, 24000000);
            at91_set_A_periph(AT91_PIN_PB27, 0);
          }
        }
#endif

	/* Ethernet */
	at91_add_device_eth(&csb437tl_eth_data);
	/* USB Host */
	at91_add_device_usbh();
	/* USB Device */
	at91_add_device_udc(&csb437tl_udc_data);
	/* Compact Flash */
	at91_set_gpio_direction(AT91_PIN_PB22, 1, 1);	/* IOIS16 */
	at91_add_device_cf(&csb437tl_cf_data);
	/* MMC */
	at91_add_device_mmc(&csb437tl_mmc_data);

#if defined(CONFIG_FB_VOYAGER_GX)
       platform_device_register(&at91_panel_dev);
#endif
       platform_device_register(&sm501_8051_dev);
       platform_device_register(&ac97_dev);

}
Exemplo n.º 23
0
static void __init onearm_board_init(void)
{
	/* Serial */
	at91_add_device_serial();
	/* Ethernet */
	at91_add_device_eth(&onearm_eth_data);
	/* USB Host */
	at91_add_device_usbh(&onearm_usbh_data);
	/* USB Device */
	at91_add_device_udc(&onearm_udc_data);
}
Exemplo n.º 24
0
static void __init onearm_board_init(void)
{
	
	at91_add_device_serial();
	
	at91_add_device_eth(&onearm_eth_data);
	
	at91_add_device_usbh(&onearm_usbh_data);
	
	at91_add_device_udc(&onearm_udc_data);
}
Exemplo n.º 25
0
static void __init snapper9260_board_init(void)
{
	at91_add_device_i2c(snapper9260_i2c_devices,
			    ARRAY_SIZE(snapper9260_i2c_devices));
	at91_add_device_serial();
	at91_add_device_usbh(&snapper9260_usbh_data);
	at91_add_device_udc(&snapper9260_udc_data);
	at91_add_device_eth(&snapper9260_macb_data);
	at91_add_device_ssc(AT91SAM9260_ID_SSC, (ATMEL_SSC_TF | ATMEL_SSC_TK |
						 ATMEL_SSC_TD | ATMEL_SSC_RD));
	snapper9260_add_device_nand();
}
Exemplo n.º 26
0
static void __init ek_board_init(void)
{
	/* Ethernet */
	at91_add_device_eth(&ek_eth_data);
	/* USB Host */
	at91_add_device_usbh();
	/* USB Device */
	at91_add_device_udc(&ek_udc_data);
	/* MMC */
	at91_set_gpio_direction(AT91_PIN_PB22, 0, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). default: MMC */
	at91_add_device_mmc(&ek_mmc_data);
	/* VGA */
	ek_add_device_video();
}
static void __init stamp9g20evb_board_init(void)
{
	stamp9g20_board_init();
	/*          */
	at91_add_device_usbh(&usbh_data);
	/*            */
	at91_add_device_udc(&stamp9g20evb_udc_data);
	/*          */
	at91_add_device_eth(&macb_data);
	/*     */
	at91_add_device_i2c(NULL, 0);
	/*      */
	at91_gpio_leds(stamp9g20evb_leds, ARRAY_SIZE(stamp9g20evb_leds));
}
Exemplo n.º 28
0
static void __init csb337_board_init(void)
{
	/* Ethernet */
	at91_add_device_eth(&csb337_eth_data);
	/* USB Host */
	at91_add_device_usbh();
	/* USB Device */
	at91_add_device_udc(&csb337_udc_data);
	/* Compact Flash */
	at91_set_gpio_direction(AT91_PIN_PB22, 1, 1);	/* IOIS16 */
	at91_add_device_cf(&csb337_cf_data);
	/* MMC */
	at91_add_device_mmc(&csb337_mmc_data);
}
static void __init stamp9g20evb_board_init(void)
{
	stamp9g20_board_init();
	/* USB Host */
	at91_add_device_usbh(&usbh_data);
	/* USB Device */
	at91_add_device_udc(&stamp9g20evb_udc_data);
	/* Ethernet */
	at91_add_device_eth(&macb_data);
	/* I2C */
	at91_add_device_i2c(NULL, 0);
	/* LEDs */
	at91_gpio_leds(stamp9g20evb_leds, ARRAY_SIZE(stamp9g20evb_leds));
}
static void __init kafa_board_init(void)
{
	/*        */
	at91_add_device_serial();
	/*          */
	at91_add_device_eth(&kafa_eth_data);
	/*          */
	at91_add_device_usbh(&kafa_usbh_data);
	/*            */
	at91_add_device_udc(&kafa_udc_data);
	/*     */
	at91_add_device_i2c(NULL, 0);
	/*     */
	at91_add_device_spi(NULL, 0);
}