void hw_data_init(void)
{
*prcm = &dra7xx_prcm;
if (is_dra72x())
*dplls_data = &dra72x_dplls;
else if (is_dra76x())
*dplls_data = &dra76x_dplls;
else
*dplls_data = &dra7xx_dplls;
*ctrl = &dra7xx_ctrl;
}
int board_fit_config_name_match(const char *name)
{
if (is_dra72x()) {
if (board_is_dra71x_evm()) {
if (!strcmp(name, "dra71-evm"))
return 0;
}else if(board_is_dra72x_revc_or_later()) {
if (!strcmp(name, "dra72-evm-revc"))
return 0;
} else if (!strcmp(name, "dra72-evm")) {
return 0;
}
} else if (is_dra76x() && !strcmp(name, "dra76-evm")) {
return 0;
} else if (!is_dra72x() && !is_dra76x() && !strcmp(name, "dra7-evm")) {
return 0;
}
return -1;
}
/* VTT regulator enable */
static inline void vtt_regulator_enable(void)
{
if (omap_hw_init_context() == OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL)
return;
/* Do not enable VTT for DRA722 or DRA76x */
if (is_dra72x() || is_dra76x())
return;
/*
* EVM Rev G and later use gpio7_11 for DDR3 termination.
* This is safe enough to do on older revs.
*/
gpio_request(GPIO_DDR_VTT_EN, "ddr_vtt_en");
gpio_direction_output(GPIO_DDR_VTT_EN, 1);
}
int board_late_init(void)
{
#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
char *name = "unknown";
if (is_dra72x()) {
if (board_is_dra72x_revc_or_later())
name = "dra72x-revc";
else if (board_is_dra71x_evm())
name = "dra71x";
else
name = "dra72x";
} else if (is_dra76x()) {
name = "dra76x";
} else {
name = "dra7xx";
}
set_board_info_env(name);
/*
* Default FIT boot on HS devices. Non FIT images are not allowed
* on HS devices.
*/
if (get_device_type() == HS_DEVICE)
env_set("boot_fit", "1");
omap_die_id_serial();
omap_set_fastboot_vars();
/*
* Hook the LDO1 regulator to EN pin. This applies only to LP8733
* Rest all regulators are hooked to EN Pin at reset.
*/
if (board_is_dra71x_evm())
palmas_i2c_write_u8(LP873X_I2C_SLAVE_ADDR, 0x9, 0x7);
#endif
return 0;
}
void recalibrate_iodelay(void)
{
struct pad_conf_entry const *pads, *delta_pads = NULL;
struct iodelay_cfg_entry const *iodelay;
int npads, niodelays, delta_npads = 0;
int ret;
switch (omap_revision()) {
case DRA722_ES1_0:
case DRA722_ES2_0:
case DRA722_ES2_1:
pads = dra72x_core_padconf_array_common;
npads = ARRAY_SIZE(dra72x_core_padconf_array_common);
if (board_is_dra71x_evm()) {
pads = dra71x_core_padconf_array;
npads = ARRAY_SIZE(dra71x_core_padconf_array);
iodelay = dra71_iodelay_cfg_array;
niodelays = ARRAY_SIZE(dra71_iodelay_cfg_array);
} else if (board_is_dra72x_revc_or_later()) {
delta_pads = dra72x_rgmii_padconf_array_revc;
delta_npads =
ARRAY_SIZE(dra72x_rgmii_padconf_array_revc);
iodelay = dra72_iodelay_cfg_array_revc;
niodelays = ARRAY_SIZE(dra72_iodelay_cfg_array_revc);
} else {
delta_pads = dra72x_rgmii_padconf_array_revb;
delta_npads =
ARRAY_SIZE(dra72x_rgmii_padconf_array_revb);
iodelay = dra72_iodelay_cfg_array_revb;
niodelays = ARRAY_SIZE(dra72_iodelay_cfg_array_revb);
}
break;
case DRA752_ES1_0:
case DRA752_ES1_1:
pads = dra74x_core_padconf_array;
npads = ARRAY_SIZE(dra74x_core_padconf_array);
iodelay = dra742_es1_1_iodelay_cfg_array;
niodelays = ARRAY_SIZE(dra742_es1_1_iodelay_cfg_array);
break;
case DRA762_ACD_ES1_0:
case DRA762_ES1_0:
pads = dra76x_core_padconf_array;
npads = ARRAY_SIZE(dra76x_core_padconf_array);
iodelay = dra76x_es1_0_iodelay_cfg_array;
niodelays = ARRAY_SIZE(dra76x_es1_0_iodelay_cfg_array);
break;
default:
case DRA752_ES2_0:
case DRA762_ABZ_ES1_0:
pads = dra74x_core_padconf_array;
npads = ARRAY_SIZE(dra74x_core_padconf_array);
iodelay = dra742_es2_0_iodelay_cfg_array;
niodelays = ARRAY_SIZE(dra742_es2_0_iodelay_cfg_array);
/* Setup port1 and port2 for rgmii with 'no-id' mode */
clrset_spare_register(1, 0, RGMII2_ID_MODE_N_MASK |
RGMII1_ID_MODE_N_MASK);
break;
}
/* Setup I/O isolation */
ret = __recalibrate_iodelay_start();
if (ret)
goto err;
/* Do the muxing here */
do_set_mux32((*ctrl)->control_padconf_core_base, pads, npads);
/* Now do the weird minor deltas that should be safe */
if (delta_npads)
do_set_mux32((*ctrl)->control_padconf_core_base,
delta_pads, delta_npads);
if (is_dra76x())
/* Set mux for MCAN instead of DCAN1 */
clrsetbits_le32((*ctrl)->control_core_control_spare_rw,
MCAN_SEL_ALT_MASK, MCAN_SEL);
/* Setup IOdelay configuration */
ret = do_set_iodelay((*ctrl)->iodelay_config_base, iodelay, niodelays);
err:
/* Closeup.. remove isolation */
__recalibrate_iodelay_end(ret);
}
