/** * This function will initial M487 board. */ void rt_hw_board_init(void) { clock_init(); #ifdef RT_USING_HEAP #ifdef __CC_ARM rt_system_heap_init((void*)&Image$$RW_IRAM1$$ZI$$Limit, (void*)SRAM_END); #elif __ICCARM__ rt_system_heap_init(__segment_end("HEAP"), (void*)SRAM_END); #else /* init memory system */ rt_system_heap_init((void*)&__bss_end, (void*)&__ram_top); #endif #endif /* RT_USING_HEAP */ rt_hw_uart_init(); #ifdef RT_USING_CONSOLE rt_console_set_device(RT_CONSOLE_DEVICE_NAME); #endif SysTick_Config(SystemCoreClock / RT_TICK_PER_SECOND); NVIC_SetPriorityGrouping(7); #ifdef RT_USING_COMPONENTS_INIT rt_components_board_init(); #endif }
/** * This function will initial LPC40xx board. */ void rt_hw_board_init() { //init low level drivers. e.g. cpu uart etc. rt_components_board_init(); //redirect RTT stdio to CONSOLE device rt_console_set_device(RT_CONSOLE_DEVICE_NAME); }
/** * This function will initial LPC17xx board. */ void rt_hw_board_init() { /* NVIC Configuration */ #define NVIC_VTOR_MASK 0x3FFFFF80 #ifdef VECT_TAB_RAM /* Set the Vector Table base location at 0x10000000 */ SCB->VTOR = (0x10000000 & NVIC_VTOR_MASK); #else /* VECT_TAB_FLASH */ /* Set the Vector Table base location at 0x00000000 */ SCB->VTOR = (0x00000000 & NVIC_VTOR_MASK); #endif /* init systick */ SysTick_Config(SystemCoreClock / RT_TICK_PER_SECOND - 1); /* set pend exception priority */ NVIC_SetPriority(PendSV_IRQn, (1 << __NVIC_PRIO_BITS) - 1); /*init uart device*/ rt_hw_uart_init(); rt_console_set_device(RT_CONSOLE_DEVICE_NAME); #if LPC_EXT_SDRAM == 1 lpc_sdram_hw_init(); mpu_init(); #endif #ifdef RT_USING_COMPONENTS_INIT /* initialization board with RT-Thread Components */ rt_components_board_init(); #endif }
void rt_hw_board_init(void) { sysctl_pll_set_freq(SYSCTL_PLL0, 800000000UL); sysctl_pll_set_freq(SYSCTL_PLL1, 400000000UL); /* Init FPIOA */ fpioa_init(); /* Dmac init */ dmac_init(); /* initalize interrupt */ rt_hw_interrupt_init(); /* initialize hardware interrupt */ rt_hw_uart_init(); rt_hw_tick_init(); #ifdef RT_USING_SMP rt_hw_clint_ipi_enable(); #endif #ifdef RT_USING_CONSOLE /* set console device */ rt_console_set_device(RT_CONSOLE_DEVICE_NAME); #endif /* RT_USING_CONSOLE */ #ifdef RT_USING_HEAP rt_kprintf("heap: [0x%08x - 0x%08x]\n", (rt_ubase_t) RT_HW_HEAP_BEGIN, (rt_ubase_t) RT_HW_HEAP_END); /* initialize memory system */ rt_system_heap_init(RT_HW_HEAP_BEGIN, RT_HW_HEAP_END); #endif #ifdef RT_USING_COMPONENTS_INIT rt_components_board_init(); #endif }
/** * This function will initial board. */ void rt_hw_board_init(void) { /* must call first to configure gpio Alternate functions according the hardware design */ wm_gpio_config(); wm_sys_clk_config(); #ifdef RT_USING_HEAP rt_system_heap_init((void *)HEAP_BEGIN, (void *)HEAP_END); #endif #ifdef RT_USING_COMPONENTS_INIT rt_components_board_init(); #endif #ifdef RT_USING_CONSOLE rt_console_set_device(RT_CONSOLE_DEVICE_NAME); #endif #if TLS_CONFIG_HARD_CRYPTO tls_crypto_init(); #endif NVIC_SystemLPConfig(NVIC_LP_SLEEPDEEP, ENABLE); rt_thread_idle_sethook(_idle_hook_callback); }
/** * This function will initial STM32 board. */ void rt_hw_board_init(void) { /* NVIC Configuration */ NVIC_Configuration(); /* Configure the SysTick */ SysTick_Config( SystemCoreClock / RT_TICK_PER_SECOND ); //SysTick_Configuration(); #if STM32_EXT_SRAM EXT_SRAM_Configuration(); #endif rt_hw_usart_init(); #ifdef RT_USING_CONSOLE rt_console_set_device(RT_CONSOLE_DEVICE_NAME); #endif #ifdef RT_USING_COMPONENTS_INIT rt_components_board_init(); #endif stm32_hw_pin_init(); ports_initial(); }
/** * This function will initialize beaglebone board */ void rt_hw_board_init(void) { enable_neon_fpu(); disable_strict_align_check(); rt_components_board_init(); rt_console_set_device(RT_CONSOLE_DEVICE_NAME); }
void rt_hw_board_init() { emsk_mux_init(); rt_hw_uart_init(); rt_components_board_init(); rt_console_set_device(RT_CONSOLE_DEVICE_NAME); }
/***************************************************************************//** * @brief * Initialize the hardware drivers. * * @details * * @note * ******************************************************************************/ void rt_hw_driver_init(void) { /* Initialize USART */ #if (defined(BSP_USING_USART1) || defined(BSP_USING_USART2) || \ defined(BSP_USING_USART3)) bsp_hw_usart_init(); #endif /* Setup Console */ rt_console_set_device(CONSOLE_DEVICE); #if defined(RT_USING_COMPONENTS_INIT) rt_components_board_init(); #else /* Initialize SPI */ # if (defined(BSP_USING_SPI1) || defined(BSP_USING_SPI2) || \ defined(BSP_USING_SPI3)) bsp_hw_spi_init(); # endif /* Initialize LED */ # if (defined(BSP_USING_LED1) || defined(BSP_USING_LED2)) board_hw_led_init(); # endif /* Initialize OLED */ # if defined(BSP_USING_OLED) # if (OLED_DEVICE_INTERFACE == INTERFACE_8BIT_80XX) bsp_hw_oled_init(); # endif # endif /* Initialize RTC */ # if defined(BSP_USING_RTC) bsp_hw_rtc_init(); # endif /* Initialize USB */ # if defined(BSP_USING_USB) bsp_hw_usb_core_init(); # if defined(BSP_USING_USB_VIRTUAL_COM) board_hw_usb_com_init(); # endif # if defined(BSP_USING_USB_HID_MOUSE) bsp_hw_usb_mouse_init(); # endif # endif #endif }
/** * This function will initial FM3 Easy Kit board. */ void rt_hw_board_init(void) { /* disable all analog input. */ FM3_GPIO->ADE = 0; /* init systick */ SysTick_Config(SystemCoreClock/RT_TICK_PER_SECOND); /* initialize UART device */ rt_hw_serial_init(); /* set console as UART device */ rt_console_set_device(RT_CONSOLE_DEVICE_NAME); #ifdef RT_USING_COMPONENTS_INIT rt_components_board_init(); #endif }
/** * This function will initialize beaglebone board */ void rt_hw_board_init(void) { /* initialize hardware interrupt */ rt_hw_interrupt_init(); /* initialize system heap */ rt_system_heap_init(HEAP_BEGIN, HEAP_END); rt_components_board_init(); rt_console_set_device(RT_CONSOLE_DEVICE_NAME); rt_thread_idle_sethook(idle_wfi); #ifdef RT_USING_SMP /* install IPI handle */ rt_hw_ipi_handler_install(RT_SCHEDULE_IPI, rt_scheduler_ipi_handler); #endif }
/** * This function will initial LPC15xx board. */ void rt_hw_board_init() { /* init systick */ SysTick_Config(SystemCoreClock / RT_TICK_PER_SECOND); /* set pend exception priority */ NVIC_SetPriority(PendSV_IRQn, (1 << __NVIC_PRIO_BITS) - 1); /*init uart device*/ rt_hw_uart_init(); rt_console_set_device(RT_CONSOLE_DEVICE_NAME); #ifdef RT_USING_COMPONENTS_INIT /* initialization board with RT-Thread Components */ rt_components_board_init(); #endif }
/** * This function will initial board. */ void rt_hw_board_init(void) { extern uint32_t SystemCoreClock; SysTick_Config(SystemCoreClock/RT_TICK_PER_SECOND); #ifdef RT_USING_HEAP rt_system_heap_init((void*)HEAP_BEGIN, (void*)HEAP_END); #endif #ifdef RT_USING_COMPONENTS_INIT rt_components_board_init(); #endif #ifdef RT_USING_CONSOLE rt_hw_uart_init(); rt_console_set_device(RT_CONSOLE_DEVICE_NAME); #endif }
/** * This function will initial STM32 board. */ void rt_hw_board_init() { /* NVIC Configuration */ NVIC_Configuration(); /* Configure the SysTick */ RCC_Configuration(); SysTick_Config(SystemCoreClock / RT_TICK_PER_SECOND); /* Call components board initial (use INIT_BOARD_EXPORT()) */ #ifdef RT_USING_COMPONENTS_INIT rt_components_board_init(); #endif #ifdef RT_USING_CONSOLE rt_console_set_device(RT_CONSOLE_DEVICE_NAME); #endif /* Print RCC freq info */ #ifdef PRINT_RCC_FREQ_INFO print_rcc_freq_info(); #endif }
/** * This function will initial Nuvoton board. */ void rt_hw_board_init() { /* NVIC Configuration */ NVIC_Configuration(); /* Configure the system clock */ rt_hw_system_init(); /* Configure the SysTick */ SysTick_Config(SystemCoreClock / RT_TICK_PER_SECOND); /* Initial usart deriver, and set console device */ rt_hw_usart_init(); #ifdef RT_USING_HEAP rt_system_heap_init((void *)M05X_SRAM_BEGIN, (void *)M05X_SRAM_END); #endif #ifdef RT_USING_COMPONENTS_INIT rt_components_board_init(); #endif #ifdef RT_USING_CONSOLE rt_console_set_device(RT_CONSOLE_DEVICE_NAME); #endif }
/** * This function will initial STM32 board. */ void rt_hw_board_init() { rccConfiguration(); /* NVIC Configuration */ NVIC_Configuration(); /* Configure the SysTick */ SysTick_Config(SystemCoreClock / RT_TICK_PER_SECOND); #ifdef RT_USING_COMPONENTS_INIT rt_components_board_init(); #else //stm32_hw_usart_init(); stm32_hw_pin_init(); #endif #ifdef RT_USING_CONSOLE rt_console_set_device(CONSOLE_DEVICE); #endif }
void rt_hw_board_init(void) { rt_hw_cache_init(); /* init hardware interrupt */ rt_hw_interrupt_init(); rt_hw_uart_init(); #ifdef RT_USING_CONSOLE /* set console device */ rt_console_set_device(RT_CONSOLE_DEVICE_NAME); #endif /* RT_USING_CONSOLE */ #ifdef RT_USING_HEAP /* init memory system */ rt_system_heap_init(RT_HW_HEAP_BEGIN, RT_HW_HEAP_END); #endif #ifdef RT_USING_COMPONENTS_INIT rt_components_board_init(); #endif rt_hw_ost_init(); }
/** * This function will initial STM32 board. */ void rt_hw_board_init() { /* Configure the MPU attributes as Write Through */ //mpu_init(); /* Enable the CPU Cache */ CPU_CACHE_Enable(); /* STM32F7xx HAL library initialization: - Configure the Flash ART accelerator on ITCM interface - Configure the Systick to generate an interrupt each 1 msec - Set NVIC Group Priority to 4 - Global MSP (MCU Support Package) initialization */ HAL_Init(); /* Configure the system clock @ 200 Mhz */ SystemClock_Config(); /* init systick */ SysTick_Config(SystemCoreClock / RT_TICK_PER_SECOND); /* set pend exception priority */ NVIC_SetPriority(PendSV_IRQn, (1 << __NVIC_PRIO_BITS) - 1); #ifdef RT_USING_COMPONENTS_INIT rt_components_board_init(); #endif #ifdef RT_USING_EXT_SDRAM rt_system_heap_init((void*)EXT_SDRAM_BEGIN, (void*)EXT_SDRAM_END); sram_init(); #else rt_system_heap_init((void*)HEAP_BEGIN, (void*)HEAP_END); #endif #ifdef RT_USING_CONSOLE rt_console_set_device(RT_CONSOLE_DEVICE_NAME); #endif }
/** * This function will initial TMS320F28379D board. */ void rt_hw_board_init() { /* Configure the system clock @ 84 Mhz */ InitSysCtrl(); DINT; InitPieCtrl(); IER = 0x0000; IFR = 0x0000; InitPieVectTable(); EALLOW; // This is needed to write to EALLOW protected registers PieVectTable.TIMER2_INT = &cpu_timer2_isr; PieVectTable.RTOS_INT = &RTOSINT_Handler; EDIS; InitCpuTimers(); ConfigCpuTimer(&CpuTimer2, 200, 1000000 / RT_TICK_PER_SECOND); CpuTimer2Regs.TCR.all = 0x4000; IER |= M_INT14; #ifdef RT_USING_HEAP rt_system_heap_init((void *)HEAP_BEGIN, (void *)HEAP_END); #endif rt_hw_sci_init(); #ifdef RT_USING_COMPONENTS_INIT rt_components_board_init(); #endif #ifdef RT_USING_CONSOLE rt_console_set_device(RT_CONSOLE_DEVICE_NAME); #endif rt_interrupt_leave_sethook((void (*)(void))trap_rtosint); }