void mbx_init(void)
{
volatile immap_t *immr = (immap_t *)CFG_IMMR;
volatile memctl8xx_t *memctl = &immr->im_memctl;
ulong speed, refclock, plprcr, sccr;
/* real-time clock status and control register */
immr->im_sitk.sitk_rtcsck = KAPWR_KEY;
immr->im_sit.sit_rtcsc = 0x00C3;
/* SIEL and SIMASK Registers (see MBX PRG 2-3) */
immr->im_siu_conf.sc_simask = 0x00000000;
immr->im_siu_conf.sc_siel = 0xAAAA0000;
immr->im_siu_conf.sc_tesr = 0xFFFFFFFF;
/*
* Prepare access to i2c bus. The MBX offers 3 devices on the i2c
* bus:
* 1. Vital Product Data (contains clock speeds, mac-address etc,
* see vpd.h)
* 2. RAM Specs (see dimm.h)
* 2. DIMM Specs (see dimm.h)
*/
vpd_init();
/* system clock and reset control register */
immr->im_clkrstk.cark_sccrk = KAPWR_KEY;
sccr = immr->im_clkrst.car_sccr;
sccr &= SCCR_MASK;
sccr |= CFG_SCCR;
immr->im_clkrst.car_sccr = sccr;
speed = board_get_cpufreq();
refclock = get_reffreq();
plprcr = CFG_PLPRCR;
plprcr |= ((speed + refclock / 2) / refclock - 1) << 20;
immr->im_clkrst.car_plprcr = plprcr;
/*
* preliminary setup of memory controller:
* - map pci registers
* - map configuation and status registers
* - DON'T map ram/flash/rom yet, this is done in initdram()
*/
switch(speed / 1000000)
{
case 40:
memctl->memc_br4 = CFG_NVRAM_BASE | 0x401;
memctl->memc_or4 = CFG_NVRAM_OR | 0x920;
break;
case 50:
memctl->memc_br4 = CFG_NVRAM_BASE | 0x401;
memctl->memc_or4 = CFG_NVRAM_OR | 0x930;
break;
default:
hang();
break;
}
memctl->memc_br5 = CFG_PCIMEM_BASE | 0x001;
memctl->memc_or5 = CFG_PCIMEM_OR;
memctl->memc_br6 = CFG_PCIBRIDGE_BASE | 0x001;
memctl->memc_or6 = CFG_PCIBRIDGE_OR;
}
void mbx_init (void)
{
volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immr->im_memctl;
ulong speed, plprcr, sccr;
ulong br0_32 = memctl->memc_br0 & 0x400;
/* real-time clock status and control register */
immr->im_sitk.sitk_rtcsck = KAPWR_KEY;
immr->im_sit.sit_rtcsc = 0x00C3;
/* SIEL and SIMASK Registers (see MBX PRG 2-3) */
immr->im_siu_conf.sc_simask = 0x00000000;
immr->im_siu_conf.sc_siel = 0xAAAA0000;
immr->im_siu_conf.sc_tesr = 0xFFFFFFFF;
/*
* Prepare access to i2c bus. The MBX offers 3 devices on the i2c bus:
* 1. Vital Product Data (contains clock speeds, MAC address etc, see vpd.h)
* 2. RAM Specs (see dimm.h)
* 2. DIMM Specs (see dimm.h)
*/
vpd_init ();
/* system clock and reset control register */
immr->im_clkrstk.cark_sccrk = KAPWR_KEY;
sccr = immr->im_clkrst.car_sccr;
sccr &= SCCR_MASK;
sccr |= CONFIG_SYS_SCCR;
immr->im_clkrst.car_sccr = sccr;
speed = board_get_cpufreq ();
#if ((CONFIG_SYS_PLPRCR & PLPRCR_MF_MSK) != 0)
plprcr = CONFIG_SYS_PLPRCR;
#else
plprcr = immr->im_clkrst.car_plprcr;
plprcr &= PLPRCR_MF_MSK; /* isolate MF field */
plprcr |= CONFIG_SYS_PLPRCR; /* reset control bits */
#endif
#ifdef CONFIG_SYS_USE_OSCCLK /* See doc/README.MBX ! */
plprcr |= ((speed + get_reffreq() / 2) / refclock - 1) << 20;
#endif
immr->im_clkrstk.cark_plprcrk = KAPWR_KEY;
immr->im_clkrst.car_plprcr = plprcr;
/*
* preliminary setup of memory controller:
* - map Flash, otherwise configuration/status
* registers won't be accessible when read
* by board_init_f.
* - map NVRAM and configuation/status registers.
* - map pci registers.
* - DON'T map ram yet, this is done in initdram().
*/
switch (speed / 1000000) {
case 40:
memctl->memc_br0 = 0xFE000000 | br0_32 | 1;
memctl->memc_or0 = 0xFF800930;
memctl->memc_or4 = CONFIG_SYS_NVRAM_OR | 0x920;
memctl->memc_br4 = CONFIG_SYS_NVRAM_BASE | 0x401;
break;
case 50:
memctl->memc_br0 = 0xFE000000 | br0_32 | 1;
memctl->memc_or0 = 0xFF800940;
memctl->memc_or4 = CONFIG_SYS_NVRAM_OR | 0x930;
memctl->memc_br4 = CONFIG_SYS_NVRAM_BASE | 0x401;
break;
default:
hang ();
break;
}
#ifdef CONFIG_USE_PCI
memctl->memc_or5 = CONFIG_SYS_PCIMEM_OR;
memctl->memc_br5 = CONFIG_SYS_PCIMEM_BASE | 0x001;
memctl->memc_or6 = CONFIG_SYS_PCIBRIDGE_OR;
memctl->memc_br6 = CONFIG_SYS_PCIBRIDGE_BASE | 0x001;
#endif
/*
* FIXME: I do not understand why I have to call this to
* initialise the control register here before booting from
* the PCMCIA card but if I do not the Linux kernel falls
* over in a big heap. If you can answer this question I
* would like to know about it.
*/
board_ether_init();
}
