//*****************************************************************************
//
// MPU9150 Application error handler. Show the user if we have encountered an
// I2C error.
//
//*****************************************************************************
void
MPU9150AppErrorHandler(char *pcFilename, uint_fast32_t ui32Line)
{
//
// Set terminal color to red and print error status and locations
//
UARTprintf("\033[31;1m");
UARTprintf("Error: %d, File: %s, Line: %d\n"
"See I2C status definitions in sensorlib\\i2cm_drv.h\n",
g_vui8ErrorFlag, pcFilename, ui32Line);
//
// Return terminal color to normal
//
UARTprintf("\033[0m");
//
// Set RGB Color to RED
//
g_pui32Colors[0] = 0xFFFF;
g_pui32Colors[1] = 0;
g_pui32Colors[2] = 0;
RGBColorSet(g_pui32Colors);
//
// Increase blink rate to get attention
//
RGBBlinkRateSet(10.0f);
//
// Go to sleep wait for interventions. A more robust application could
// attempt corrective actions here.
//
while(1)
{
//
// Do Nothing
//
}
}
void initsensorhub(void)
{
//
// Enable port B used for motion interrupt.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
//
// Initialize the UART.
//
ConfigureUART();
//
// Print the welcome message to the terminal.
//
UARTprintf("\033[2JMPU9150 Raw Example\n");
//
// Set the color to a purple approximation.
//
g_pui32Colors[RED] = 0x8000;
g_pui32Colors[BLUE] = 0x8000;
g_pui32Colors[GREEN] = 0x0000;
//
// Initialize RGB driver.
//
RGBInit(0);
RGBColorSet(g_pui32Colors);
RGBIntensitySet(0.5f);
RGBEnable();
//
// The I2C3 peripheral must be enabled before use.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_I2C3);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
//
// Configure the pin muxing for I2C3 functions on port D0 and D1.
//
ROM_GPIOPinConfigure(GPIO_PD0_I2C3SCL);
ROM_GPIOPinConfigure(GPIO_PD1_I2C3SDA);
//
// Select the I2C function for these pins. This function will also
// configure the GPIO pins pins for I2C operation, setting them to
// open-drain operation with weak pull-ups. Consult the data sheet
// to see which functions are allocated per pin.
//
GPIOPinTypeI2CSCL(GPIO_PORTD_BASE, GPIO_PIN_0);
ROM_GPIOPinTypeI2C(GPIO_PORTD_BASE, GPIO_PIN_1);
//
// Configure and Enable the GPIO interrupt. Used for INT signal from the
// MPU9150
//
ROM_GPIOPinTypeGPIOInput(GPIO_PORTB_BASE, GPIO_PIN_2);
GPIOIntEnable(GPIO_PORTB_BASE, GPIO_PIN_2);
ROM_GPIOIntTypeSet(GPIO_PORTB_BASE, GPIO_PIN_2, GPIO_FALLING_EDGE);
ROM_IntEnable(INT_GPIOB);
//
// Keep only some parts of the systems running while in sleep mode.
// GPIOB is for the MPU9150 interrupt pin.
// UART0 is the virtual serial port
// TIMER0, TIMER1 and WTIMER5 are used by the RGB driver
// I2C3 is the I2C interface to the ISL29023
//
ROM_SysCtlPeripheralClockGating(true);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UART0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_TIMER0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_TIMER1);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_I2C3);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_WTIMER5);
//
// Enable interrupts to the processor.
//
ROM_IntMasterEnable();
//
// Initialize I2C3 peripheral.
//
I2CMInit(&g_sI2CInst, I2C3_BASE, INT_I2C3, 0xff, 0xff,
ROM_SysCtlClockGet());
//
// Initialize the MPU9150 Driver.
//
MPU9150Init(&g_sMPU9150Inst, &g_sI2CInst, MPU9150_I2C_ADDRESS,
MPU9150AppCallback, &g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Write application specifice sensor configuration such as filter settings
// and sensor range settings.
//
g_sMPU9150Inst.pui8Data[0] = MPU9150_CONFIG_DLPF_CFG_94_98;
g_sMPU9150Inst.pui8Data[1] = MPU9150_GYRO_CONFIG_FS_SEL_250;
g_sMPU9150Inst.pui8Data[2] = (MPU9150_ACCEL_CONFIG_ACCEL_HPF_5HZ |
MPU9150_ACCEL_CONFIG_AFS_SEL_2G);
MPU9150Write(&g_sMPU9150Inst, MPU9150_O_CONFIG, g_sMPU9150Inst.pui8Data, 3,
MPU9150AppCallback, &g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Configure the data ready interrupt pin output of the MPU9150.
//
g_sMPU9150Inst.pui8Data[0] = MPU9150_INT_PIN_CFG_INT_LEVEL |
MPU9150_INT_PIN_CFG_INT_RD_CLEAR |
MPU9150_INT_PIN_CFG_LATCH_INT_EN;
g_sMPU9150Inst.pui8Data[1] = MPU9150_INT_ENABLE_DATA_RDY_EN;
MPU9150Write(&g_sMPU9150Inst, MPU9150_O_INT_PIN_CFG,
g_sMPU9150Inst.pui8Data, 2, MPU9150AppCallback,
&g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Initialize the DCM system. 50 hz sample rate.
// accel weight = .2, gyro weight = .8, mag weight = .2
//
CompDCMInit(&g_sCompDCMInst, 1.0f / 50.0f, 0.2f, 0.6f, 0.2f);
UARTprintf("\033[2J\033[H");
UARTprintf("MPU9150 9-Axis Simple Data Application Example\n\n");
UARTprintf("\033[20GX\033[31G|\033[43GY\033[54G|\033[66GZ\n\n");
UARTprintf("Accel\033[8G|\033[31G|\033[54G|\n\n");
UARTprintf("Gyro\033[8G|\033[31G|\033[54G|\n\n");
UARTprintf("Mag\033[8G|\033[31G|\033[54G|\n\n");
UARTprintf("\n\033[20GRoll\033[31G|\033[43GPitch\033[54G|\033[66GYaw\n\n");
UARTprintf("Eulers\033[8G|\033[31G|\033[54G|\n\n");
UARTprintf("\n\033[17GQ1\033[26G|\033[35GQ2\033[44G|\033[53GQ3\033[62G|"
"\033[71GQ4\n\n");
UARTprintf("Q\033[8G|\033[26G|\033[44G|\033[62G|\n\n");
//
// Enable blinking indicates config finished successfully
//
RGBBlinkRateSet(1.0f);
//
// Initialize convenience pointers that clean up and clarify the code
// meaning. We want all the data in a single contiguous array so that
// we can make our pretty printing easier later.
//
pfAccel = pfData;
pfGyro = pfData + 3;
pfMag = pfData + 6;
pfEulers = pfData + 9;
pfQuaternion = pfData + 12;
}
//*****************************************************************************
//
// Main application entry point.
//
//*****************************************************************************
int
main(void)
{
int_fast32_t i32IPart[16], i32FPart[16];
uint_fast32_t ui32Idx, ui32CompDCMStarted;
float pfData[16];
float *pfAccel, *pfGyro, *pfMag, *pfEulers, *pfQuaternion;
//
// Initialize convenience pointers that clean up and clarify the code
// meaning. We want all the data in a single contiguous array so that
// we can make our pretty printing easier later.
//
pfAccel = pfData;
pfGyro = pfData + 3;
pfMag = pfData + 6;
pfEulers = pfData + 9;
pfQuaternion = pfData + 12;
//
// Setup the system clock to run at 40 Mhz from PLL with crystal reference
//
SysCtlClockSet(SYSCTL_SYSDIV_5 | SYSCTL_USE_PLL | SYSCTL_XTAL_16MHZ |
SYSCTL_OSC_MAIN);
//
// Enable port B used for motion interrupt.
//
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
//
// Initialize the UART.
//
ConfigureUART();
//
// Print the welcome message to the terminal.
//
UARTprintf("\033[2JMPU9150 Raw Example\n");
//
// Set the color to a purple approximation.
//
g_pui32Colors[RED] = 0x8000;
g_pui32Colors[BLUE] = 0x8000;
g_pui32Colors[GREEN] = 0x0000;
//
// Initialize RGB driver.
//
RGBInit(0);
RGBColorSet(g_pui32Colors);
RGBIntensitySet(0.5f);
RGBEnable();
//
// The I2C3 peripheral must be enabled before use.
//
SysCtlPeripheralEnable(SYSCTL_PERIPH_I2C3);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
//
// Configure the pin muxing for I2C3 functions on port D0 and D1.
//
GPIOPinConfigure(GPIO_PD0_I2C3SCL);
GPIOPinConfigure(GPIO_PD1_I2C3SDA);
//
// Select the I2C function for these pins. This function will also
// configure the GPIO pins pins for I2C operation, setting them to
// open-drain operation with weak pull-ups. Consult the data sheet
// to see which functions are allocated per pin.
//
GPIOPinTypeI2CSCL(GPIO_PORTD_BASE, GPIO_PIN_0);
GPIOPinTypeI2C(GPIO_PORTD_BASE, GPIO_PIN_1);
//
// Configure and Enable the GPIO interrupt. Used for INT signal from the
// MPU9150
//
GPIOPinTypeGPIOInput(GPIO_PORTB_BASE, GPIO_PIN_2);
GPIOIntEnable(GPIO_PORTB_BASE, GPIO_PIN_2);
GPIOIntTypeSet(GPIO_PORTB_BASE, GPIO_PIN_2, GPIO_FALLING_EDGE);
IntEnable(INT_GPIOB);
//
// Keep only some parts of the systems running while in sleep mode.
// GPIOB is for the MPU9150 interrupt pin.
// UART0 is the virtual serial port
// TIMER0, TIMER1 and WTIMER5 are used by the RGB driver
// I2C3 is the I2C interface to the ISL29023
//
SysCtlPeripheralClockGating(true);
SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOB);
SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UART0);
SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_TIMER0);
SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_TIMER1);
SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_I2C3);
SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_WTIMER5);
//
// Enable interrupts to the processor.
//
IntMasterEnable();
//
// Initialize I2C3 peripheral.
//
I2CMInit(&g_sI2CInst, I2C3_BASE, INT_I2C3, 0xff, 0xff,
SysCtlClockGet());
//
// Initialize the MPU9150 Driver.
//
MPU9150Init(&g_sMPU9150Inst, &g_sI2CInst, MPU9150_I2C_ADDRESS,
MPU9150AppCallback, &g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Write application specifice sensor configuration such as filter settings
// and sensor range settings.
//
g_sMPU9150Inst.pui8Data[0] = MPU9150_CONFIG_DLPF_CFG_94_98;
g_sMPU9150Inst.pui8Data[1] = MPU9150_GYRO_CONFIG_FS_SEL_250;
g_sMPU9150Inst.pui8Data[2] = (MPU9150_ACCEL_CONFIG_ACCEL_HPF_5HZ |
MPU9150_ACCEL_CONFIG_AFS_SEL_2G);
MPU9150Write(&g_sMPU9150Inst, MPU9150_O_CONFIG, g_sMPU9150Inst.pui8Data, 3,
MPU9150AppCallback, &g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Configure the data ready interrupt pin output of the MPU9150.
//
g_sMPU9150Inst.pui8Data[0] = MPU9150_INT_PIN_CFG_INT_LEVEL |
MPU9150_INT_PIN_CFG_INT_RD_CLEAR |
MPU9150_INT_PIN_CFG_LATCH_INT_EN;
g_sMPU9150Inst.pui8Data[1] = MPU9150_INT_ENABLE_DATA_RDY_EN;
MPU9150Write(&g_sMPU9150Inst, MPU9150_O_INT_PIN_CFG,
g_sMPU9150Inst.pui8Data, 2, MPU9150AppCallback,
&g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Initialize the DCM system. 50 hz sample rate.
// accel weight = .2, gyro weight = .8, mag weight = .2
//
CompDCMInit(&g_sCompDCMInst, 1.0f / 50.0f, 0.2f, 0.6f, 0.2f);
UARTprintf("\033[2J\033[H");
UARTprintf("MPU9150 9-Axis Simple Data Application Example\n\n");
UARTprintf("\033[20GX\033[31G|\033[43GY\033[54G|\033[66GZ\n\n");
UARTprintf("Accel\033[8G|\033[31G|\033[54G|\n\n");
UARTprintf("Gyro\033[8G|\033[31G|\033[54G|\n\n");
UARTprintf("Mag\033[8G|\033[31G|\033[54G|\n\n");
UARTprintf("\n\033[20GRoll\033[31G|\033[43GPitch\033[54G|\033[66GYaw\n\n");
UARTprintf("Eulers\033[8G|\033[31G|\033[54G|\n\n");
UARTprintf("\n\033[17GQ1\033[26G|\033[35GQ2\033[44G|\033[53GQ3\033[62G|"
"\033[71GQ4\n\n");
UARTprintf("Q\033[8G|\033[26G|\033[44G|\033[62G|\n\n");
//
// Enable blinking indicates config finished successfully
//
RGBBlinkRateSet(1.0f);
ui32CompDCMStarted = 0;
while(1)
{
//
// Go to sleep mode while waiting for data ready.
//
while(!g_vui8I2CDoneFlag)
{
SysCtlSleep();
}
//
// Clear the flag
//
g_vui8I2CDoneFlag = 0;
//
// Get floating point version of the Accel Data in m/s^2.
//
MPU9150DataAccelGetFloat(&g_sMPU9150Inst, pfAccel, pfAccel + 1,
pfAccel + 2);
//
// Get floating point version of angular velocities in rad/sec
//
MPU9150DataGyroGetFloat(&g_sMPU9150Inst, pfGyro, pfGyro + 1,
pfGyro + 2);
//
// Get floating point version of magnetic fields strength in tesla
//
MPU9150DataMagnetoGetFloat(&g_sMPU9150Inst, pfMag, pfMag + 1,
pfMag + 2);
//
// Check if this is our first data ever.
//
if(ui32CompDCMStarted == 0)
{
//
// Set flag indicating that DCM is started.
// Perform the seeding of the DCM with the first data set.
//
ui32CompDCMStarted = 1;
CompDCMMagnetoUpdate(&g_sCompDCMInst, pfMag[0], pfMag[1],
pfMag[2]);
CompDCMAccelUpdate(&g_sCompDCMInst, pfAccel[0], pfAccel[1],
pfAccel[2]);
CompDCMGyroUpdate(&g_sCompDCMInst, pfGyro[0], pfGyro[1],
pfGyro[2]);
CompDCMStart(&g_sCompDCMInst);
}
else
{
//
// DCM Is already started. Perform the incremental update.
//
CompDCMMagnetoUpdate(&g_sCompDCMInst, pfMag[0], pfMag[1],
pfMag[2]);
CompDCMAccelUpdate(&g_sCompDCMInst, pfAccel[0], pfAccel[1],
pfAccel[2]);
CompDCMGyroUpdate(&g_sCompDCMInst, -pfGyro[0], -pfGyro[1],
-pfGyro[2]);
CompDCMUpdate(&g_sCompDCMInst);
}
//
// Increment the skip counter. Skip counter is used so we do not
// overflow the UART with data.
//
g_ui32PrintSkipCounter++;
if(g_ui32PrintSkipCounter >= PRINT_SKIP_COUNT)
{
//
// Reset skip counter.
//
g_ui32PrintSkipCounter = 0;
//
// Get Euler data. (Roll Pitch Yaw)
//
CompDCMComputeEulers(&g_sCompDCMInst, pfEulers, pfEulers + 1,
pfEulers + 2);
//
// Get Quaternions.
//
CompDCMComputeQuaternion(&g_sCompDCMInst, pfQuaternion);
//
// convert mag data to micro-tesla for better human interpretation.
//
pfMag[0] *= 1e6;
pfMag[1] *= 1e6;
pfMag[2] *= 1e6;
//
// Convert Eulers to degrees. 180/PI = 57.29...
// Convert Yaw to 0 to 360 to approximate compass headings.
//
pfEulers[0] *= 57.295779513082320876798154814105f;
pfEulers[1] *= 57.295779513082320876798154814105f;
pfEulers[2] *= 57.295779513082320876798154814105f;
if(pfEulers[2] < 0)
{
pfEulers[2] += 360.0f;
}
//
// Now drop back to using the data as a single array for the
// purpose of decomposing the float into a integer part and a
// fraction (decimal) part.
//
for(ui32Idx = 0; ui32Idx < 16; ui32Idx++)
{
//
// Conver float value to a integer truncating the decimal part.
//
i32IPart[ui32Idx] = (int32_t) pfData[ui32Idx];
//
// Multiply by 1000 to preserve first three decimal values.
// Truncates at the 3rd decimal place.
//
i32FPart[ui32Idx] = (int32_t) (pfData[ui32Idx] * 1000.0f);
//
// Subtract off the integer part from this newly formed decimal
// part.
//
i32FPart[ui32Idx] = i32FPart[ui32Idx] -
(i32IPart[ui32Idx] * 1000);
//
// make the decimal part a positive number for display.
//
if(i32FPart[ui32Idx] < 0)
{
i32FPart[ui32Idx] *= -1;
}
}
//
// Print the acceleration numbers in the table.
//
UARTprintf("\033[5;17H%3d.%03d", i32IPart[0], i32FPart[0]);
UARTprintf("\033[5;40H%3d.%03d", i32IPart[1], i32FPart[1]);
UARTprintf("\033[5;63H%3d.%03d", i32IPart[2], i32FPart[2]);
//
// Print the angular velocities in the table.
//
UARTprintf("\033[7;17H%3d.%03d", i32IPart[3], i32FPart[3]);
UARTprintf("\033[7;40H%3d.%03d", i32IPart[4], i32FPart[4]);
UARTprintf("\033[7;63H%3d.%03d", i32IPart[5], i32FPart[5]);
//
// Print the magnetic data in the table.
//
UARTprintf("\033[9;17H%3d.%03d", i32IPart[6], i32FPart[6]);
UARTprintf("\033[9;40H%3d.%03d", i32IPart[7], i32FPart[7]);
UARTprintf("\033[9;63H%3d.%03d", i32IPart[8], i32FPart[8]);
//
// Print the Eulers in a table.
//
UARTprintf("\033[14;17H%3d.%03d", i32IPart[9], i32FPart[9]);
UARTprintf("\033[14;40H%3d.%03d", i32IPart[10], i32FPart[10]);
UARTprintf("\033[14;63H%3d.%03d", i32IPart[11], i32FPart[11]);
//
// Print the quaternions in a table format.
//
UARTprintf("\033[19;14H%3d.%03d", i32IPart[12], i32FPart[12]);
UARTprintf("\033[19;32H%3d.%03d", i32IPart[13], i32FPart[13]);
UARTprintf("\033[19;50H%3d.%03d", i32IPart[14], i32FPart[14]);
UARTprintf("\033[19;68H%3d.%03d", i32IPart[15], i32FPart[15]);
}
}
}
//*****************************************************************************
//
// Main 'C' Language entry point.
//
//*****************************************************************************
int
main(void)
{
float fTemperature, fPressure, fAltitude;
int32_t i32IntegerPart;
int32_t i32FractionPart;
//
// Setup the system clock to run at 40 MHz from PLL with crystal reference
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_5 | SYSCTL_USE_PLL | SYSCTL_XTAL_16MHZ |
SYSCTL_OSC_MAIN);
//
// Initialize the UART.
//
ConfigureUART();
//
// Print the welcome message to the terminal.
//
UARTprintf("\033[2JBMP180 Example\n");
//
// Set the color to a white approximation.
//
g_pui32Colors[RED] = 0x8000;
g_pui32Colors[BLUE] = 0x8000;
g_pui32Colors[GREEN] = 0x8000;
//
// Initialize RGB driver. Use a default intensity and blink rate.
//
RGBInit(0);
RGBColorSet(g_pui32Colors);
RGBIntensitySet(0.5f);
RGBEnable();
//
// The I2C3 peripheral must be enabled before use.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_I2C3);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
//
// Configure the pin muxing for I2C3 functions on port D0 and D1.
// This step is not necessary if your part does not support pin muxing.
//
ROM_GPIOPinConfigure(GPIO_PD0_I2C3SCL);
ROM_GPIOPinConfigure(GPIO_PD1_I2C3SDA);
//
// Select the I2C function for these pins. This function will also
// configure the GPIO pins pins for I2C operation, setting them to
// open-drain operation with weak pull-ups. Consult the data sheet
// to see which functions are allocated per pin.
//
GPIOPinTypeI2CSCL(GPIO_PORTD_BASE, GPIO_PIN_0);
ROM_GPIOPinTypeI2C(GPIO_PORTD_BASE, GPIO_PIN_1);
//
// Initialize the GPIO for the LED.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_1);
ROM_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_1, 0x00);
//
// Enable interrupts to the processor.
//
ROM_IntMasterEnable();
//
// Initialize the I2C3 peripheral.
//
I2CMInit(&g_sI2CInst, I2C3_BASE, INT_I2C3, 0xff, 0xff,
ROM_SysCtlClockGet());
//
// Initialize the BMP180.
//
BMP180Init(&g_sBMP180Inst, &g_sI2CInst, BMP180_I2C_ADDRESS,
BMP180AppCallback, &g_sBMP180Inst);
//
// Wait for initialization callback to indicate reset request is complete.
//
while(g_vui8DataFlag == 0)
{
//
// Wait for I2C Transactions to complete.
//
}
//
// Reset the data ready flag
//
g_vui8DataFlag = 0;
//
// Enable the system ticks at 10 Hz.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / (10 * 3));
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// After all the init and config we start blink the LED
//
RGBBlinkRateSet(1.0f);
//
// Begin the data collection and printing. Loop Forever.
//
while(1)
{
//
// Read the data from the BMP180 over I2C. This command starts a
// temperature measurement. Then polls until temperature is ready.
// Then automatically starts a pressure measurement and polls for that
// to complete. When both measurement are complete and in the local
// buffer then the application callback is called from the I2C
// interrupt context. Polling is done on I2C interrupts allowing
// processor to continue doing other tasks as needed.
//
BMP180DataRead(&g_sBMP180Inst, BMP180AppCallback, &g_sBMP180Inst);
while(g_vui8DataFlag == 0)
{
//
// Wait for the new data set to be available.
//
}
//
// Reset the data ready flag.
//
g_vui8DataFlag = 0;
//
// Get a local copy of the latest temperature data in float format.
//
BMP180DataTemperatureGetFloat(&g_sBMP180Inst, &fTemperature);
//
// Convert the floats to an integer part and fraction part for easy
// print.
//
i32IntegerPart = (int32_t) fTemperature;
i32FractionPart =(int32_t) (fTemperature * 1000.0f);
i32FractionPart = i32FractionPart - (i32IntegerPart * 1000);
if(i32FractionPart < 0)
{
i32FractionPart *= -1;
}
//
// Print temperature with three digits of decimal precision.
//
UARTprintf("Temperature %3d.%03d\t\t", i32IntegerPart, i32FractionPart);
//
// Get a local copy of the latest air pressure data in float format.
//
BMP180DataPressureGetFloat(&g_sBMP180Inst, &fPressure);
//
// Convert the floats to an integer part and fraction part for easy
// print.
//
i32IntegerPart = (int32_t) fPressure;
i32FractionPart =(int32_t) (fPressure * 1000.0f);
i32FractionPart = i32FractionPart - (i32IntegerPart * 1000);
if(i32FractionPart < 0)
{
i32FractionPart *= -1;
}
//
// Print Pressure with three digits of decimal precision.
//
UARTprintf("Pressure %3d.%03d\t\t", i32IntegerPart, i32FractionPart);
//
// Calculate the altitude.
//
fAltitude = 44330.0f * (1.0f - powf(fPressure / 101325.0f,
1.0f / 5.255f));
//
// Convert the floats to an integer part and fraction part for easy
// print.
//
i32IntegerPart = (int32_t) fAltitude;
i32FractionPart =(int32_t) (fAltitude * 1000.0f);
i32FractionPart = i32FractionPart - (i32IntegerPart * 1000);
if(i32FractionPart < 0)
{
i32FractionPart *= -1;
}
//
// Print altitude with three digits of decimal precision.
//
UARTprintf("Altitude %3d.%03d", i32IntegerPart, i32FractionPart);
//
// Print new line.
//
UARTprintf("\n");
//
// Delay to keep printing speed reasonable. About 100 milliseconds.
//
ROM_SysCtlDelay(ROM_SysCtlClockGet() / (10 * 3));
}//while end
}
//*****************************************************************************
//
// Main 'C' Language entry point.
//
//*****************************************************************************
int
main(void)
{
float fAmbient;
int32_t i32IntegerPart, i32FractionPart;
uint8_t ui8Mask;
//
// Setup the system clock to run at 40 Mhz from PLL with crystal reference
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_5 | SYSCTL_USE_PLL | SYSCTL_XTAL_16MHZ |
SYSCTL_OSC_MAIN);
//
// Enable the peripherals used by this example.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
//
// Initialize the UART and its pins.
//
ConfigureUART();
//
// Print the welcome message to the terminal.
//
UARTprintf("\033[2JISL29023 Example\n");
//
// Set the color to a white approximation.
//
g_pui32Colors[RED] = 0x8000;
g_pui32Colors[BLUE] = 0x8000;
g_pui32Colors[GREEN] = 0x8000;
//
// Initialize RGB driver. Use a default intensity and blink rate.
//
RGBInit(0);
RGBColorSet(g_pui32Colors);
RGBIntensitySet(0.5f);
RGBEnable();
//
// The I2C3 peripheral must be enabled before use.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_I2C3);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
//
// Configure the pin muxing for I2C3 functions on port D0 and D1.
// This step is not necessary if your part does not support pin muxing.
//
ROM_GPIOPinConfigure(GPIO_PD0_I2C3SCL);
ROM_GPIOPinConfigure(GPIO_PD1_I2C3SDA);
//
// Select the I2C function for these pins. This function will also
// configure the GPIO pins pins for I2C operation, setting them to
// open-drain operation with weak pull-ups. Consult the data sheet
// to see which functions are allocated per pin.
//
GPIOPinTypeI2CSCL(GPIO_PORTD_BASE, GPIO_PIN_0);
ROM_GPIOPinTypeI2C(GPIO_PORTD_BASE, GPIO_PIN_1);
//
// Configure and Enable the GPIO interrupt. Used for INT signal from the
// ISL29023
//
ROM_GPIOPinTypeGPIOInput(GPIO_PORTE_BASE, GPIO_PIN_5);
GPIOIntEnable(GPIO_PORTE_BASE, GPIO_PIN_5);
ROM_GPIOIntTypeSet(GPIO_PORTE_BASE, GPIO_PIN_5, GPIO_FALLING_EDGE);
ROM_IntEnable(INT_GPIOE);
//
// Keep only some parts of the systems running while in sleep mode.
// GPIOE is for the ISL29023 interrupt pin.
// UART0 is the virtual serial port
// TIMER0, TIMER1 and WTIMER5 are used by the RGB driver
// I2C3 is the I2C interface to the ISL29023
//
ROM_SysCtlPeripheralClockGating(true);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOE);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UART0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_TIMER0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_TIMER1);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_I2C3);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_WTIMER5);
//
// Configure desired interrupt priorities. Setting the I2C interrupt to be
// of more priority than SysTick and the GPIO interrupt means those
// interrupt routines can use the I2CM_DRV Application context does not use
// I2CM_DRV API and GPIO and SysTick are at the same priority level. This
// prevents re-entrancy problems with I2CM_DRV but keeps the MCU in sleep
// state as much as possible. UART is at least priority so it can operate
// in the background.
//
ROM_IntPrioritySet(INT_I2C3, 0x00);
ROM_IntPrioritySet(FAULT_SYSTICK, 0x40);
ROM_IntPrioritySet(INT_GPIOE, 0x80);
ROM_IntPrioritySet(INT_UART0, 0x80);
//
// Enable interrupts to the processor.
//
ROM_IntMasterEnable();
//
// Initialize I2C3 peripheral.
//
I2CMInit(&g_sI2CInst, I2C3_BASE, INT_I2C3, 0xff, 0xff,
ROM_SysCtlClockGet());
//
// Initialize the ISL29023 Driver.
//
ISL29023Init(&g_sISL29023Inst, &g_sI2CInst, ISL29023_I2C_ADDRESS,
ISL29023AppCallback, &g_sISL29023Inst);
//
// Wait for transaction to complete
//
ISL29023AppI2CWait(__FILE__, __LINE__);
//
// Configure the ISL29023 to measure ambient light continuously. Set a 8
// sample persistence before the INT pin is asserted. Clears the INT flag.
// Persistence setting of 8 is sufficient to ignore camera flashes.
//
ui8Mask = (ISL29023_CMD_I_OP_MODE_M | ISL29023_CMD_I_INT_PERSIST_M |
ISL29023_CMD_I_INT_FLAG_M);
ISL29023ReadModifyWrite(&g_sISL29023Inst, ISL29023_O_CMD_I, ~ui8Mask,
(ISL29023_CMD_I_OP_MODE_ALS_CONT |
ISL29023_CMD_I_INT_PERSIST_8),
ISL29023AppCallback, &g_sISL29023Inst);
//
// Wait for transaction to complete
//
ISL29023AppI2CWait(__FILE__, __LINE__);
//
// Configure the upper threshold to 80% of maximum value
//
g_sISL29023Inst.pui8Data[1] = 0xCC;
g_sISL29023Inst.pui8Data[2] = 0xCC;
ISL29023Write(&g_sISL29023Inst, ISL29023_O_INT_HT_LSB,
g_sISL29023Inst.pui8Data, 2, ISL29023AppCallback,
&g_sISL29023Inst);
//
// Wait for transaction to complete
//
ISL29023AppI2CWait(__FILE__, __LINE__);
//
// Configure the lower threshold to 20% of maximum value
//
g_sISL29023Inst.pui8Data[1] = 0x33;
g_sISL29023Inst.pui8Data[2] = 0x33;
ISL29023Write(&g_sISL29023Inst, ISL29023_O_INT_LT_LSB,
g_sISL29023Inst.pui8Data, 2, ISL29023AppCallback,
&g_sISL29023Inst);
//
// Wait for transaction to complete
//
ISL29023AppI2CWait(__FILE__, __LINE__);
//
//Configure and enable SysTick Timer
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// After all the init and config we start blink the LED
//
RGBBlinkRateSet(1.0f);
//
// Loop Forever
//
while(1)
{
ROM_SysCtlSleep();
if(g_vui8DataFlag)
{
g_vui8DataFlag = 0;
//
// Get a local floating point copy of the latest light data
//
ISL29023DataLightVisibleGetFloat(&g_sISL29023Inst, &fAmbient);
//
// Perform the conversion from float to a printable set of integers
//
i32IntegerPart = (int32_t)fAmbient;
i32FractionPart = (int32_t)(fAmbient * 1000.0f);
i32FractionPart = i32FractionPart - (i32IntegerPart * 1000);
if(i32FractionPart < 0)
{
i32FractionPart *= -1;
}
//
// Print the temperature as integer and fraction parts.
//
UARTprintf("Visible Lux: %3d.%03d\n", i32IntegerPart,
i32FractionPart);
//
// Check if the intensity of light has crossed a threshold. If so
// then adjust range of sensor readings to track intensity.
//
if(g_vui8IntensityFlag)
{
//
// Disable the low priority interrupts leaving only the I2C
// interrupt enabled.
//
ROM_IntPriorityMaskSet(0x40);
//
// Reset the intensity trigger flag.
//
g_vui8IntensityFlag = 0;
//
// Adjust the lux range.
//
ISL29023AppAdjustRange(&g_sISL29023Inst);
//
// Now we must manually clear the flag in the ISL29023
// register.
//
ISL29023Read(&g_sISL29023Inst, ISL29023_O_CMD_I,
g_sISL29023Inst.pui8Data, 1, ISL29023AppCallback,
&g_sISL29023Inst);
//
// Wait for transaction to complete
//
ISL29023AppI2CWait(__FILE__, __LINE__);
//
// Disable priority masking so all interrupts are enabled.
//
ROM_IntPriorityMaskSet(0);
}
}
}
}
//*****************************************************************************
//
// Main 'C' Language entry point.
//
//*****************************************************************************
int
main(void)
{
float fAmbient, fObject;
int_fast32_t i32IntegerPart;
int_fast32_t i32FractionPart;
//
// Setup the system clock to run at 40 Mhz from PLL with crystal reference
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_5 | SYSCTL_USE_PLL | SYSCTL_XTAL_16MHZ |
SYSCTL_OSC_MAIN);
//
// Enable the peripherals used by this example.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
//
// Initialize the UART.
//
ConfigureUART();
//
// Print the welcome message to the terminal.
//
UARTprintf("\033[2J\033[1;1HTMP006 Example\n");
//
// Setup the color of the RGB LED.
//
g_pui32Colors[RED] = 0;
g_pui32Colors[BLUE] = 0xFFFF;
g_pui32Colors[GREEN] = 0;
//
// Initialize the RGB Driver and start RGB blink operation.
//
RGBInit(0);
RGBColorSet(g_pui32Colors);
RGBIntensitySet(0.5f);
RGBEnable();
//
// The I2C3 peripheral must be enabled before use.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_I2C3);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
//
// Configure the pin muxing for I2C3 functions on port D0 and D1.
// This step is not necessary if your part does not support pin muxing.
//
ROM_GPIOPinConfigure(GPIO_PD0_I2C3SCL);
ROM_GPIOPinConfigure(GPIO_PD1_I2C3SDA);
//
// Select the I2C function for these pins. This function will also
// configure the GPIO pins pins for I2C operation, setting them to
// open-drain operation with weak pull-ups. Consult the data sheet
// to see which functions are allocated per pin.
//
GPIOPinTypeI2CSCL(GPIO_PORTD_BASE, GPIO_PIN_0);
ROM_GPIOPinTypeI2C(GPIO_PORTD_BASE, GPIO_PIN_1);
//
// Configure and Enable the GPIO interrupt. Used for DRDY from the TMP006
//
ROM_GPIOPinTypeGPIOInput(GPIO_PORTE_BASE, GPIO_PIN_0);
GPIOIntEnable(GPIO_PORTE_BASE, GPIO_PIN_0);
ROM_GPIOIntTypeSet(GPIO_PORTE_BASE, GPIO_PIN_0, GPIO_FALLING_EDGE);
ROM_IntEnable(INT_GPIOE);
//
// Keep only some parts of the systems running while in sleep mode.
// GPIOE is for the TMP006 data ready interrupt.
// UART0 is the virtual serial port
// TIMER0, TIMER1 and WTIMER5 are used by the RGB driver
// I2C3 is the I2C interface to the TMP006
//
ROM_SysCtlPeripheralClockGating(true);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOE);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UART0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_TIMER0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_TIMER1);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_I2C3);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_WTIMER5);
//
// Enable interrupts to the processor.
//
ROM_IntMasterEnable();
//
// Initialize I2C3 peripheral.
//
I2CMInit(&g_sI2CInst, I2C3_BASE, INT_I2C3, 0xff, 0xff,
SysCtlClockGet());
//
// Initialize the TMP006
//
TMP006Init(&g_sTMP006Inst, &g_sI2CInst, TMP006_I2C_ADDRESS,
TMP006AppCallback, &g_sTMP006Inst);
//
// Put the processor to sleep while we wait for the I2C driver to
// indicate that the transaction is complete.
//
while((g_vui8DataFlag == 0) && (g_vui8ErrorFlag == 0))
{
ROM_SysCtlSleep();
}
//
// If an error occurred call the error handler immediately.
//
if(g_vui8ErrorFlag)
{
TMP006AppErrorHandler(__FILE__, __LINE__);
}
//
// clear the data flag for next use.
//
g_vui8DataFlag = 0;
//
// Delay for 10 milliseconds for TMP006 reset to complete.
// Not explicitly required. Datasheet does not say how long a reset takes.
//
ROM_SysCtlDelay(ROM_SysCtlClockGet() / (100 * 3));
//
// Enable the DRDY pin indication that a conversion is in progress.
//
TMP006ReadModifyWrite(&g_sTMP006Inst, TMP006_O_CONFIG,
~TMP006_CONFIG_EN_DRDY_PIN_M,
TMP006_CONFIG_EN_DRDY_PIN, TMP006AppCallback,
&g_sTMP006Inst);
//
// Wait for the DRDY enable I2C transaction to complete.
//
while((g_vui8DataFlag == 0) && (g_vui8ErrorFlag == 0))
{
ROM_SysCtlSleep();
}
//
// If an error occurred call the error handler immediately.
//
if(g_vui8ErrorFlag)
{
TMP006AppErrorHandler(__FILE__, __LINE__);
}
//
// clear the data flag for next use.
//
g_vui8DataFlag = 0;
//
// Last thing before the loop start blinking to show we got this far and
// the tmp006 is setup and ready for auto measure
//
RGBBlinkRateSet(1.0f);
//
// Loop Forever
//
while(1)
{
//
// Put the processor to sleep while we wait for the TMP006 to
// signal that data is ready. Also continue to sleep while I2C
// transactions get the raw data from the TMP006
//
while((g_vui8DataFlag == 0) && (g_vui8ErrorFlag == 0))
{
ROM_SysCtlSleep();
}
//
// If an error occurred call the error handler immediately.
//
if(g_vui8ErrorFlag)
{
TMP006AppErrorHandler(__FILE__, __LINE__);
}
//
// Reset the flag
//
g_vui8DataFlag = 0;
//
// Get a local copy of the latest data in float format.
//
TMP006DataTemperatureGetFloat(&g_sTMP006Inst, &fAmbient, &fObject);
//
// Convert the floating point ambient temperature to an integer part
// and fraction part for easy printing.
//
i32IntegerPart = (int32_t)fAmbient;
i32FractionPart = (int32_t)(fAmbient * 1000.0f);
i32FractionPart = i32FractionPart - (i32IntegerPart * 1000);
if(i32FractionPart < 0)
{
i32FractionPart *= -1;
}
UARTprintf("Ambient %3d.%03d\t", i32IntegerPart, i32FractionPart);
//
// Convert the floating point ambient temperature to an integer part
// and fraction part for easy printing.
//
i32IntegerPart = (int32_t)fObject;
i32FractionPart = (int32_t)(fObject * 1000.0f);
i32FractionPart = i32FractionPart - (i32IntegerPart * 1000);
if(i32FractionPart < 0)
{
i32FractionPart *= -1;
}
UARTprintf("Object %3d.%03d\n", i32IntegerPart, i32FractionPart);
}
}
//*****************************************************************************
//
// Main application entry point.
//
//*****************************************************************************
int main(void) {
int_fast32_t i32IPart[17], i32FPart[17];
uint_fast32_t ui32Idx, ui32CompDCMStarted;
float pfData[17];
float *pfAccel, *pfGyro, *pfMag, *pfEulers, *pfQuaternion;
float *direction;
//
// Initialize convenience pointers that clean up and clarify the code
// meaning. We want all the data in a single contiguous array so that
// we can make our pretty printing easier later.
//
pfAccel = pfData;
pfGyro = pfData + 3;
pfMag = pfData + 6;
pfEulers = pfData + 9;
pfQuaternion = pfData + 12;
direction = pfData + 16;
//
// Setup the system clock to run at 40 Mhz from PLL with crystal reference
//
ROM_SysCtlClockSet(
SYSCTL_SYSDIV_5 | SYSCTL_USE_PLL | SYSCTL_XTAL_16MHZ
| SYSCTL_OSC_MAIN);
//
// Enable port E used for motion interrupt.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
//
// Enable port F used for calibration.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
//
// Initialize the UART.
//
ConfigureUART();
/* EEPROM SETTINGS */
SysCtlPeripheralEnable(SYSCTL_PERIPH_EEPROM0); // EEPROM activate
EEPROMInit(); // EEPROM start
//
// Print the welcome message to the terminal.
//
UARTprintf("\033[2JMPU9150 Raw Example\n");
//
// Set the color to a purple approximation.
//
g_pui32Colors[RED] = 0x8000;
g_pui32Colors[BLUE] = 0x8000;
g_pui32Colors[GREEN] = 0x8000;
//
// Initialize RGB driver.
//
RGBInit(0);
RGBColorSet(g_pui32Colors);
RGBIntensitySet(0.5f);
RGBEnable();
// Initialize BGLib
bglib_output = output;
ConfigureBLE();
//
// The I2C3 peripheral must be enabled before use.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_I2C3);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
//
// Configure the pin muxing for I2C3 functions on port D0 and D1.
//
ROM_GPIOPinConfigure(GPIO_PD0_I2C3SCL);
ROM_GPIOPinConfigure(GPIO_PD1_I2C3SDA);
//
// Select the I2C function for these pins. This function will also
// configure the GPIO pins pins for I2C operation, setting them to
// open-drain operation with weak pull-ups. Consult the data sheet
// to see which functions are allocated per pin.
//
GPIOPinTypeI2CSCL(GPIO_PORTD_BASE, GPIO_PIN_0);
ROM_GPIOPinTypeI2C(GPIO_PORTD_BASE, GPIO_PIN_1);
//
// Configure and Enable the GPIO interrupt. Used for INT signal from the
// MPU9150
//
ROM_GPIOPinTypeGPIOInput(GPIO_PORTE_BASE, GPIO_PIN_2);
GPIOIntEnable(GPIO_PORTE_BASE, GPIO_PIN_2);
ROM_GPIOIntTypeSet(GPIO_PORTE_BASE, GPIO_PIN_2, GPIO_FALLING_EDGE);
ROM_IntEnable(INT_GPIOE);
//
// Keep only some parts of the systems running while in sleep mode.
// GPIOE is for the MPU9150 interrupt pin.
// UART0 is the virtual serial port
// TIMER0, TIMER1 and WTIMER5 are used by the RGB driver
// I2C3 is the I2C interface to the ISL29023
//
ROM_SysCtlPeripheralClockGating(true);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOE);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UART0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_TIMER0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_TIMER1);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_I2C3);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_WTIMER5);
//
// Enable interrupts to the processor.
//
ROM_IntMasterEnable();
//
// Initialize I2C3 peripheral.
//
I2CMInit(&g_sI2CInst, I2C3_BASE, INT_I2C3, 0xff, 0xff,
ROM_SysCtlClockGet());
//
// Initialize the MPU9150 Driver.
//
MPU9150Init(&g_sMPU9150Inst, &g_sI2CInst, MPU9150_I2C_ADDRESS,
MPU9150AppCallback, &g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Configure the sampling rate to 1000 Hz / (1+24).
//
g_sMPU9150Inst.pui8Data[0] = 24;
MPU9150Write(&g_sMPU9150Inst, MPU9150_O_SMPLRT_DIV, g_sMPU9150Inst.pui8Data,
1, MPU9150AppCallback, &g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Write application specifice sensor configuration such as filter settings
// and sensor range settings.
//
g_sMPU9150Inst.pui8Data[0] = MPU9150_CONFIG_DLPF_CFG_94_98;
g_sMPU9150Inst.pui8Data[1] = MPU9150_GYRO_CONFIG_FS_SEL_250;
g_sMPU9150Inst.pui8Data[2] = (MPU9150_ACCEL_CONFIG_ACCEL_HPF_5HZ
| MPU9150_ACCEL_CONFIG_AFS_SEL_2G);
// g_sMPU9150Inst.pui8Data[2] = MPU9150_ACCEL_CONFIG_AFS_SEL_2G;
MPU9150Write(&g_sMPU9150Inst, MPU9150_O_CONFIG, g_sMPU9150Inst.pui8Data, 3,
MPU9150AppCallback, &g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Configure the data ready interrupt pin output of the MPU9150.
//
g_sMPU9150Inst.pui8Data[0] = MPU9150_INT_PIN_CFG_INT_LEVEL
| MPU9150_INT_PIN_CFG_INT_RD_CLEAR
| MPU9150_INT_PIN_CFG_LATCH_INT_EN;
g_sMPU9150Inst.pui8Data[1] = MPU9150_INT_ENABLE_DATA_RDY_EN;
MPU9150Write(&g_sMPU9150Inst, MPU9150_O_INT_PIN_CFG,
g_sMPU9150Inst.pui8Data, 2, MPU9150AppCallback, &g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Initialize the DCM system. 40 hz sample rate.
// accel weight = .2, gyro weight = .8, mag weight = .2
//
CompDCMInit(&g_sCompDCMInst, 1.0f / 40.0f, 0.2f, 0.6f, 0.2f);
//
// Enable blinking indicates config finished successfully
//
RGBBlinkRateSet(1.0f);
//
// Configure and Enable the GPIO interrupt. Used for calibration
//
HWREG(GPIO_PORTF_BASE + GPIO_O_LOCK) = GPIO_LOCK_KEY;
HWREG(GPIO_PORTF_BASE + GPIO_O_CR) |= 0x01;
ROM_GPIOPinTypeGPIOInput(GPIO_PORTF_BASE, GPIO_PIN_4);
GPIOPadConfigSet(GPIO_PORTF_BASE, GPIO_PIN_4, GPIO_STRENGTH_2MA,
GPIO_PIN_TYPE_STD_WPU);
ROM_IntEnable(INT_GPIOF);
ROM_GPIOIntTypeSet(GPIO_PORTF_BASE, GPIO_PIN_4, GPIO_FALLING_EDGE);
GPIOIntEnable(GPIO_PORTF_BASE, GPIO_PIN_4);
g_calibrationState = 0;
ui32CompDCMStarted = 0;
// Configure the white noise, read the error from EEPROM
EEPROMRead((uint32_t *) zeroErrorAccel,
EEPROM_ZERO_ERROR_ACCELERATION_ADDRESS, 12);
EEPROMRead((uint32_t *) linearErrorAccel,
EEPROM_LINEAR_ERROR_ACCELERATION_ADDRESS, 12);
EEPROMRead((uint32_t *) zeroErrorGyro, EEPROM_ZERO_ERROR_GYROSCOPE_ADDRESS,
12);
while (1) {
//
// Go to sleep mode while waiting for data ready.
//
while (!g_vui8I2CDoneFlag) {
//ROM_SysCtlSleep();
}
//
// Clear the flag
//
g_vui8I2CDoneFlag = 0;
//
// Get floating point version of the Accel Data in m/s^2.
//
MPU9150DataAccelGetFloat(&g_sMPU9150Inst, pfAccel, pfAccel + 1,
pfAccel + 2);
//
// Get floating point version of angular velocities in rad/sec
//
MPU9150DataGyroGetFloat(&g_sMPU9150Inst, pfGyro, pfGyro + 1,
pfGyro + 2);
//
// Get floating point version of magnetic fields strength in tesla
//
MPU9150DataMagnetoGetFloat(&g_sMPU9150Inst, pfMag, pfMag + 1,
pfMag + 2);
if (g_calibrationState == 2) {
zeroErrorAccel[0] = (pfAccel[0]
+ zeroErrorAccel[0] * g_calibrationCount)
/ (g_calibrationCount + 1);
zeroErrorAccel[1] = (pfAccel[1]
+ zeroErrorAccel[1] * g_calibrationCount)
/ (g_calibrationCount + 1);
accelAtGravity[2] = (pfAccel[2]
+ accelAtGravity[2] * g_calibrationCount)
/ (g_calibrationCount + 1);
zeroErrorGyro[0] = (pfGyro[0]
+ zeroErrorGyro[0] * g_calibrationCount)
/ (g_calibrationCount + 1);
zeroErrorGyro[1] = (pfGyro[1]
+ zeroErrorGyro[1] * g_calibrationCount)
/ (g_calibrationCount + 1);
zeroErrorGyro[2] = (pfGyro[2]
+ zeroErrorGyro[2] * g_calibrationCount)
/ (g_calibrationCount + 1);
g_calibrationCount++;
if (g_calibrationCount > 500) {
Calibration();
}
continue;
} else if (g_calibrationState == 4) {
zeroErrorAccel[2] = (pfAccel[2]
+ zeroErrorAccel[2] * g_calibrationCount)
/ (g_calibrationCount + 1);
accelAtGravity[1] = (pfAccel[1]
+ accelAtGravity[1] * g_calibrationCount)
/ (g_calibrationCount + 1);
g_calibrationCount++;
if (g_calibrationCount > 500) {
Calibration();
}
continue;
} else if (g_calibrationState == 6) {
accelAtGravity[0] = (pfAccel[0]
+ accelAtGravity[0] * g_calibrationCount)
/ (g_calibrationCount + 1);
g_calibrationCount++;
if (g_calibrationCount > 500) {
Calibration();
}
continue;
}
// Cancel out white noise
// pfAccel[0] = pfAccel[0] - zeroErrorAccel[0];
// pfAccel[1] = pfAccel[1] - zeroErrorAccel[1];
// pfAccel[2] = pfAccel[2] - zeroErrorAccel[2];
// pfGyro[0] = pfGyro[0] - zeroErrorGyro[0];
// pfGyro[1] = pfGyro[1] - zeroErrorGyro[1];
// pfGyro[2] = pfGyro[2] - zeroErrorGyro[2];
// // Straighten out linear noise
// pfAccel[0] = pfAccel[0] * (1 + linearErrorAccel[0]);
// pfAccel[1] = pfAccel[1] * (1 + linearErrorAccel[1]);
// pfAccel[2] = pfAccel[2] * (1 + linearErrorAccel[2]);
//
// Check if this is our first data ever.
//
if (ui32CompDCMStarted == 0) {
//
// Set flag indicating that DCM is started.
// Perform the seeding of the DCM with the first data set.
//
ui32CompDCMStarted = 1;
CompDCMMagnetoUpdate(&g_sCompDCMInst, pfMag[0], pfMag[1], pfMag[2]);
CompDCMAccelUpdate(&g_sCompDCMInst, pfAccel[0], pfAccel[1],
pfAccel[2]);
CompDCMGyroUpdate(&g_sCompDCMInst, pfGyro[0], pfGyro[1], pfGyro[2]);
CompDCMStart(&g_sCompDCMInst);
} else {
//
// DCM Is already started. Perform the incremental update.
//
CompDCMMagnetoUpdate(&g_sCompDCMInst, pfMag[0], pfMag[1], pfMag[2]);
CompDCMAccelUpdate(&g_sCompDCMInst, pfAccel[0], pfAccel[1],
pfAccel[2]);
CompDCMGyroUpdate(&g_sCompDCMInst, -pfGyro[0], -pfGyro[1],
-pfGyro[2]);
CompDCMUpdate(&g_sCompDCMInst);
}
//
// Increment the skip counter. Skip counter is used so we do not
// overflow the UART with data.
//
g_ui32PrintSkipCounter++;
if (g_ui32PrintSkipCounter >= PRINT_SKIP_COUNT) {
//
// Reset skip counter.
//
g_ui32PrintSkipCounter = 0;
//
// Get Euler data. (Roll Pitch Yaw)
//
CompDCMComputeEulers(&g_sCompDCMInst, pfEulers, pfEulers + 1,
pfEulers + 2);
//
// Get Quaternions.
//
CompDCMComputeQuaternion(&g_sCompDCMInst, pfQuaternion);
//
// convert mag data to micro-tesla for better human interpretation.
//
pfMag[0] *= 1e6;
pfMag[1] *= 1e6;
pfMag[2] *= 1e6;
//
// Convert Eulers to degrees. 180/PI = 57.29...
// Convert Yaw to 0 to 360 to approximate compass headings.
//
pfEulers[0] *= 57.295779513082320876798154814105f;
pfEulers[1] *= 57.295779513082320876798154814105f;
pfEulers[2] *= 57.295779513082320876798154814105f;
if (pfEulers[2] < 0) {
pfEulers[2] += 360.0f;
}
// Use pfMag to display degrees of the Magnetomer's x-axis
// (y-axis of accelerometer and gyroscope) to the east of
// magnetic north pole
// direction[0] = 0;
// if (pfMag[1] == 0) {
// if (pfMag[0] > 0) {
// direction[0] = 0;
// } else {
// direction[0] = 180;
// }
// } else if (pfMag[1] > 0) {
// direction[0] = 90 - atan2f(pfMag[0], pfMag[1]) * 180 / 3.14159265359;
// } else if (pfMag[1] < 0) {
// direction[0] = 270 - atan2f(pfMag[0], pfMag[1]) * 180 / 3.14159265359;
// }
//
// Now drop back to using the data as a single array for the
// purpose of decomposing the float into a integer part and a
// fraction (decimal) part.
//
for (ui32Idx = 0; ui32Idx < 17; ui32Idx++) {
//
// Conver float value to a integer truncating the decimal part.
//
i32IPart[ui32Idx] = (int32_t) pfData[ui32Idx];
//
// Multiply by 1000 to preserve first three decimal values.
// Truncates at the 3rd decimal place.
//
i32FPart[ui32Idx] = (int32_t) (pfData[ui32Idx] * 1000.0f);
//
// Subtract off the integer part from this newly formed decimal
// part.
//
i32FPart[ui32Idx] = i32FPart[ui32Idx]
- (i32IPart[ui32Idx] * 1000);
//
// make the decimal part a positive number for display.
//
if (i32FPart[ui32Idx] < 0) {
i32FPart[ui32Idx] *= -1;
}
}
if (g_bleUserFlag == 1) {
g_bleFlag = 0;
ble_cmd_attributes_write(58, 0, 12, (uint8_t*)pfEuler);
while (g_bleFlag == 0) {
}
} else if (g_bleDisconnectFlag == 1) {
ConfigureBLE();
}
//
// Print the acceleration numbers in the table.
//
// UARTprintf("%3d.%03d, ", i32IPart[0], i32FPart[0]);
// UARTprintf("%3d.%03d, ", i32IPart[1], i32FPart[1]);
// UARTprintf("%3d.%03d\n", i32IPart[2], i32FPart[2]);
//
// //
// // Print the angular velocities in the table.
// //
// UARTprintf("%3d.%03d, ", i32IPart[3], i32FPart[3]);
// UARTprintf("%3d.%03d, ", i32IPart[4], i32FPart[4]);
// UARTprintf("%3d.%03d\n", i32IPart[5], i32FPart[5]);
//
// //
// // Print the magnetic data in the table.
// //
// UARTprintf("%3d.%03d, ", i32IPart[6], i32FPart[6]);
// UARTprintf("%3d.%03d, ", i32IPart[7], i32FPart[7]);
// UARTprintf("%3d.%03d\n", i32IPart[8], i32FPart[8]);
//
// //
// // Print the direction in the table.
// //
// UARTprintf("%3d.%03d\n", i32IPart[16], i32FPart[16]);
// //
// // Print the Eulers in a table.
// //
// UARTprintf("%3d.%03d, ", i32IPart[9], i32FPart[9]);
// UARTprintf("%3d.%03d, ", i32IPart[10], i32FPart[10]);
// UARTprintf("%3d.%03d\n", i32IPart[11], i32FPart[11]);
//
// //
// // Print the quaternions in a table format.
// //
// UARTprintf("\033[19;14H%3d.%03d", i32IPart[12], i32FPart[12]);
// UARTprintf("\033[19;32H%3d.%03d", i32IPart[13], i32FPart[13]);
// UARTprintf("\033[19;50H%3d.%03d", i32IPart[14], i32FPart[14]);
// UARTprintf("\033[19;68H%3d.%03d", i32IPart[15], i32FPart[15]);
}
}
}
//*****************************************************************************
//
// Calibration state machine
//
//*****************************************************************************
void Calibration() {
switch (g_calibrationState) {
case 0: {
g_calibrationState++;
//
// Reset errors to default
//
zeroErrorAccel[0] = 0.3530;
zeroErrorAccel[1] = 0.1563;
zeroErrorAccel[2] = -0.3140;
EEPROMProgram((uint32_t *) zeroErrorAccel,
EEPROM_ZERO_ERROR_ACCELERATION_ADDRESS, 12);
zeroErrorGyro[0] = 0.0526;
zeroErrorGyro[1] = 0.0156;
zeroErrorGyro[2] = 0.0157;
EEPROMProgram((uint32_t *) zeroErrorGyro,
EEPROM_ZERO_ERROR_GYROSCOPE_ADDRESS, 12);
//
// Set the color to RED.
//
RGBBlinkRateSet(0.0f);
g_pui32Colors[RED] = 0x8000;
g_pui32Colors[BLUE] = 0x0000;
g_pui32Colors[GREEN] = 0x0000;
RGBColorSet(g_pui32Colors);
RGBEnable();
break;
}
case 1: {
g_calibrationState++;
g_calibrationCount = 0;
zeroErrorAccel[0] = 0;
zeroErrorAccel[1] = 0;
zeroErrorAccel[2] = 0;
zeroErrorGyro[0] = 0;
zeroErrorGyro[1] = 0;
zeroErrorGyro[2] = 0;
RGBBlinkRateSet(1.0f);
break;
}
case 2: {
g_calibrationState++;
RGBBlinkRateSet(0.0f);
//
// Set the color to BLUE.
//
g_pui32Colors[RED] = 0x0000;
g_pui32Colors[BLUE] = 0x8000;
g_pui32Colors[GREEN] = 0x0000;
RGBColorSet(g_pui32Colors);
// Write the calibration result to EEPROM
EEPROMProgram((uint32_t *) zeroErrorAccel,
EEPROM_ZERO_ERROR_ACCELERATION_ADDRESS, 8);
EEPROMProgram((uint32_t *) zeroErrorGyro,
EEPROM_ZERO_ERROR_GYROSCOPE_ADDRESS, 12);
break;
}
case 3: {
g_calibrationState++;
g_calibrationCount = 0;
RGBBlinkRateSet(1.0f);
break;
}
case 4: {
g_calibrationState++;
RGBBlinkRateSet(0.0f);
//
// Set the color to GREEN.
//
g_pui32Colors[RED] = 0x8000;
g_pui32Colors[BLUE] = 0x8000;
g_pui32Colors[GREEN] = 0x00000;
RGBColorSet(g_pui32Colors);
// Write the calibration result to EEPROM
linearErrorAccel[1] = (accelAtGravity[1] - zeroErrorAccel[1]) / 9.81
- 1;
linearErrorAccel[2] = (accelAtGravity[2] - zeroErrorAccel[2]) / 9.81
- 1;
EEPROMProgram((uint32_t *)zeroErrorAccel+2, EEPROM_ZERO_ERROR_ACCELERATION_ADDRESS+8, 4);
EEPROMProgram((uint32_t *)linearErrorAccel+1, EEPROM_LINEAR_ERROR_ACCELERATION_ADDRESS+4, 8);
break;
}
case 5: {
g_calibrationState++;
g_calibrationCount = 0;
RGBBlinkRateSet(1.0f);
break;
}
case 6: { // finish calibration
g_calibrationState = 0;
//
// Set the color to tri-colour.
//
g_pui32Colors[RED] = 0x8000;
g_pui32Colors[BLUE] = 0x8000;
g_pui32Colors[GREEN] = 0x8000;
RGBColorSet(g_pui32Colors);
// Write the calibration result to EEPROM
linearErrorAccel[0] = (accelAtGravity[0] - zeroErrorAccel[0]) / 9.81
- 1;
EEPROMProgram((uint32_t *)linearErrorAccel, EEPROM_LINEAR_ERROR_ACCELERATION_ADDRESS, 4);
break;
}
default:
break;
}
}
static portTASK_FUNCTION(HighTask,pvParameters)
{
unsigned char frame[MAX_FRAME_SIZE];
int num_datos;
double altitud;
int16_t ejes[3];
double combustible;
float velocidad;
int tiempoSim;
while(1)
{
vTaskDelay(configTICK_RATE_HZ); //Cada seg
//Obtenemos las variables
altitud=getAltitud();
velocidad=getVelocidad();
tiempoSim=getTiempoSim();
if(altitud>0){ //Si la altitud es mayor que cero cambiamos la altitud
getEjes(ejes);
altitud += sin((ejes[PITCH]*3.14f)/180) *(velocidad*(1000/(60/tiempoSim)));
if(altitud>99999){ //99999 es el maximo del panel QT
altitud=99999;
}
//Enviamos la trama con la altitud
setAltitud(altitud);
num_datos=create_frame(frame, COMANDO_HIGH, &altitud, sizeof(altitud), MAX_FRAME_SIZE);
if (num_datos>=0){
send_frame(frame, num_datos);
}else{
logError(num_datos);
}
//Obtenemos el combustible
combustible=getCombustible();
if(combustible==0){//Si ya estamos sin combustible hacemos parpadear los led con la altitud
color[BLUE]=0xFFFF;
if(altitud<=800){
color[RED]=0xFFFF;
color[GREEN]=0x0;
}
RGBColorSet(color);
if(altitud<2000){
RGBBlinkRateSet((float)(1000/(altitud+1)));
}
tiempoSim=getTiempoSim();
//Aumentamos la velocidad a 9,8m/s^2
velocidad+=9.8*(60*tiempoSim)/1000;
setVelocidad(velocidad);
//Enviamos la nueva velocidad
num_datos=create_frame(frame, COMANDO_SPEED, &velocidad, sizeof(velocidad), MAX_FRAME_SIZE);
if (num_datos>=0){
send_frame(frame, num_datos);
}else{
logError(num_datos);
}
}
}else{ //Si la altitud es menor o igual a 0
//Variables a cero
velocidad=0;
altitud=0;
setVelocidad(velocidad);
setAltitud(altitud);
//Enviamos comando colision
if(combustible!=0) ADCSequenceDisable(ADC0_BASE,0);
num_datos=create_frame(frame, COMANDO_COLISION,NULL, 0, MAX_FRAME_SIZE);
if (num_datos>=0){
send_frame(frame, num_datos);
}else{
logError(num_datos);
}
//BLOQUEAMOS LA TIVA
vTaskDelete(sensorTaskHandle);
vTaskDelete( consumoTaskHandle );
vTaskDelete(altitudTaskHandle);
vTaskDelete( turbulenciasTaskHandle );
vTaskEndScheduler( );
while(1);
}
}
}