HAL_BOOL ar5416InitCal(struct ath_hal *ah, const struct ieee80211_channel *chan) { struct ar5416PerCal *cal = &AH5416(ah)->ah_cal; HAL_CHANNEL_INTERNAL *ichan; ichan = ath_hal_checkchannel(ah, chan); HALASSERT(ichan != AH_NULL); /* Do initial chipset-specific calibration */ if (! AH5416(ah)->ah_cal_initcal(ah, chan)) { HALDEBUG(ah, HAL_DEBUG_ANY, "%s: initial chipset calibration did " "not complete in time; noisy environment?\n", __func__); return AH_FALSE; } /* If there's PA Cal, do it */ if (AH5416(ah)->ah_cal_pacal) AH5416(ah)->ah_cal_pacal(ah, AH_TRUE); /* * Do NF calibration after DC offset and other CALs. * Per system engineers, noise floor value can sometimes be 20 dB * higher than normal value if DC offset and noise floor cal are * triggered at the same time. */ OS_REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NF); /* * This may take a while to run; make sure subsequent * calibration routines check that this has completed * before reading the value and triggering a subsequent * calibration. */ /* Initialize list pointers */ cal->cal_list = cal->cal_last = cal->cal_curr = AH_NULL; /* * Enable IQ, ADC Gain, ADC DC Offset Cals */ if (AR_SREV_HOWL(ah) || AR_SREV_SOWL_10_OR_LATER(ah)) { /* Setup all non-periodic, init time only calibrations */ /* XXX: Init DC Offset not working yet */ #if 0 if (ar5416IsCalSupp(ah, chan, ADC_DC_INIT_CAL)) { INIT_CAL(&cal->adcDcCalInitData); INSERT_CAL(cal, &cal->adcDcCalInitData); } /* Initialize current pointer to first element in list */ cal->cal_curr = cal->cal_list; if (cal->ah_cal_curr != AH_NULL && !ar5416RunInitCals(ah, 0)) return AH_FALSE; #endif } /* If Cals are supported, add them to list via INIT/INSERT_CAL */ if (ar5416IsCalSupp(ah, chan, ADC_GAIN_CAL)) { INIT_CAL(&cal->adcGainCalData); INSERT_CAL(cal, &cal->adcGainCalData); HALDEBUG(ah, HAL_DEBUG_PERCAL, "%s: enable ADC Gain Calibration.\n", __func__); } if (ar5416IsCalSupp(ah, chan, ADC_DC_CAL)) { INIT_CAL(&cal->adcDcCalData); INSERT_CAL(cal, &cal->adcDcCalData); HALDEBUG(ah, HAL_DEBUG_PERCAL, "%s: enable ADC DC Calibration.\n", __func__); } if (ar5416IsCalSupp(ah, chan, IQ_MISMATCH_CAL)) { INIT_CAL(&cal->iqCalData); INSERT_CAL(cal, &cal->iqCalData); HALDEBUG(ah, HAL_DEBUG_PERCAL, "%s: enable IQ Calibration.\n", __func__); } /* Initialize current pointer to first element in list */ cal->cal_curr = cal->cal_list; /* Kick off measurements for the first cal */ if (cal->cal_curr != AH_NULL) ar5416ResetMeasurement(ah, cal->cal_curr); /* Mark all calibrations on this channel as being invalid */ ichan->calValid = 0; return AH_TRUE; #undef MAX_CAL_CHECK }
/* * Initialize Calibration infrastructure. */ HAL_BOOL ar5416InitCal(struct ath_hal *ah, const struct ieee80211_channel *chan) { struct ar5416PerCal *cal = &AH5416(ah)->ah_cal; HAL_CHANNEL_INTERNAL *ichan; ichan = ath_hal_checkchannel(ah, chan); HALASSERT(ichan != AH_NULL); if (AR_SREV_MERLIN_10_OR_LATER(ah)) { /* Enable Rx Filter Cal */ OS_REG_CLR_BIT(ah, AR_PHY_ADC_CTL, AR_PHY_ADC_CTL_OFF_PWDADC); OS_REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_FLTR_CAL); /* Clear the carrier leak cal bit */ OS_REG_CLR_BIT(ah, AR_PHY_CL_CAL_CTL, AR_PHY_CL_CAL_ENABLE); /* kick off the cal */ OS_REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_CAL); /* Poll for offset calibration complete */ if (!ath_hal_wait(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_CAL, 0)) { HALDEBUG(ah, HAL_DEBUG_ANY, "%s: offset calibration failed to complete in 1ms; " "noisy environment?\n", __func__); return AH_FALSE; } /* Set the cl cal bit and rerun the cal a 2nd time */ /* Enable Rx Filter Cal */ OS_REG_CLR_BIT(ah, AR_PHY_ADC_CTL, AR_PHY_ADC_CTL_OFF_PWDADC); OS_REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_FLTR_CAL); OS_REG_SET_BIT(ah, AR_PHY_CL_CAL_CTL, AR_PHY_CL_CAL_ENABLE); } /* Calibrate the AGC */ OS_REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_CAL); /* Poll for offset calibration complete */ if (!ath_hal_wait(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_CAL, 0)) { HALDEBUG(ah, HAL_DEBUG_ANY, "%s: offset calibration did not complete in 1ms; " "noisy environment?\n", __func__); return AH_FALSE; } /* * Do NF calibration after DC offset and other CALs. * Per system engineers, noise floor value can sometimes be 20 dB * higher than normal value if DC offset and noise floor cal are * triggered at the same time. */ OS_REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NF); /* Initialize list pointers */ cal->cal_list = cal->cal_last = cal->cal_curr = AH_NULL; /* * Enable IQ, ADC Gain, ADC DC Offset Cals */ if (AR_SREV_SOWL_10_OR_LATER(ah)) { /* Setup all non-periodic, init time only calibrations */ /* XXX: Init DC Offset not working yet */ #if 0 if (ar5416IsCalSupp(ah, chan, ADC_DC_INIT_CAL)) { INIT_CAL(&cal->adcDcCalInitData); INSERT_CAL(cal, &cal->adcDcCalInitData); } /* Initialize current pointer to first element in list */ cal->cal_curr = cal->cal_list; if (cal->ah_cal_curr != AH_NULL && !ar5416RunInitCals(ah, 0)) return AH_FALSE; #endif } /* If Cals are supported, add them to list via INIT/INSERT_CAL */ if (ar5416IsCalSupp(ah, chan, ADC_GAIN_CAL)) { INIT_CAL(&cal->adcGainCalData); INSERT_CAL(cal, &cal->adcGainCalData); HALDEBUG(ah, HAL_DEBUG_PERCAL, "%s: enable ADC Gain Calibration.\n", __func__); } if (ar5416IsCalSupp(ah, chan, ADC_DC_CAL)) { INIT_CAL(&cal->adcDcCalData); INSERT_CAL(cal, &cal->adcDcCalData); HALDEBUG(ah, HAL_DEBUG_PERCAL, "%s: enable ADC DC Calibration.\n", __func__); } if (ar5416IsCalSupp(ah, chan, IQ_MISMATCH_CAL)) { INIT_CAL(&cal->iqCalData); INSERT_CAL(cal, &cal->iqCalData); HALDEBUG(ah, HAL_DEBUG_PERCAL, "%s: enable IQ Calibration.\n", __func__); } /* Initialize current pointer to first element in list */ cal->cal_curr = cal->cal_list; /* Kick off measurements for the first cal */ if (cal->cal_curr != AH_NULL) ar5416ResetMeasurement(ah, cal->cal_curr); /* Mark all calibrations on this channel as being invalid */ ichan->calValid = 0; return AH_TRUE; }