int __kprobes kprobe_fault_handler(struct pt_regs *regs, unsigned int fsr)
{
struct kprobe *cur = kprobe_running();
struct kprobe_ctlblk *kcb = get_kprobe_ctlblk();
switch (kcb->kprobe_status) {
case KPROBE_HIT_SS:
case KPROBE_REENTER:
/*
* We are here because the instruction being single
* stepped caused a page fault. We reset the current
* kprobe and the PC to point back to the probe address
* and allow the page fault handler to continue as a
* normal page fault.
*/
regs->ARM_pc = (long)cur->addr;
if (kcb->kprobe_status == KPROBE_REENTER) {
restore_previous_kprobe(kcb);
} else {
reset_current_kprobe();
}
break;
case KPROBE_HIT_ACTIVE:
case KPROBE_HIT_SSDONE:
/*
* We increment the nmissed count for accounting,
* we can also use npre/npostfault count for accounting
* these specific fault cases.
*/
kprobes_inc_nmissed_count(cur);
/*
* We come here because instructions in the pre/post
* handler caused the page_fault, this could happen
* if handler tries to access user space by
* copy_from_user(), get_user() etc. Let the
* user-specified handler try to fix it.
*/
if (cur->fault_handler && cur->fault_handler(cur, regs, fsr))
return 1;
break;
default:
break;
}
return 0;
}
static int __kprobes post_kprobe_handler(struct pt_regs *regs)
{
struct kprobe *cur = kprobe_running();
pr_debug("post_kprobe_handler, cur=%p\n", cur);
if (!cur)
return 0;
if (cur->post_handler) {
kprobe_status = KPROBE_HIT_SSDONE;
cur->post_handler(cur, regs, 0);
}
resume_execution(cur, regs);
reset_current_kprobe();
preempt_enable_no_resched();
return 1;
}
/*
* Called with IRQs disabled. IRQs must remain disabled from that point
* all the way until processing this kprobe is complete. The current
* kprobes implementation cannot process more than one nested level of
* kprobe, and that level is reserved for user kprobe handlers, so we can't
* risk encountering a new kprobe in an interrupt handler.
*/
void __kprobes kprobe_handler(struct pt_regs *regs)
{
struct kprobe *p, *cur;
struct kprobe_ctlblk *kcb;
kcb = get_kprobe_ctlblk();
cur = kprobe_running();
#ifdef CONFIG_THUMB2_KERNEL
/*
* First look for a probe which was registered using an address with
* bit 0 set, this is the usual situation for pointers to Thumb code.
* If not found, fallback to looking for one with bit 0 clear.
*/
p = get_kprobe((kprobe_opcode_t *)(regs->ARM_pc | 1));
if (!p)
p = get_kprobe((kprobe_opcode_t *)regs->ARM_pc);
#else /* ! CONFIG_THUMB2_KERNEL */
p = get_kprobe((kprobe_opcode_t *)regs->ARM_pc);
#endif
if (p) {
if (cur) {
/* Kprobe is pending, so we're recursing. */
switch (kcb->kprobe_status) {
case KPROBE_HIT_ACTIVE:
case KPROBE_HIT_SSDONE:
/* A pre- or post-handler probe got us here. */
kprobes_inc_nmissed_count(p);
save_previous_kprobe(kcb);
set_current_kprobe(p);
kcb->kprobe_status = KPROBE_REENTER;
singlestep(p, regs, kcb);
restore_previous_kprobe(kcb);
break;
default:
/* impossible cases */
BUG();
}
} else if (p->ainsn.insn_check_cc(regs->ARM_cpsr)) {
/* Probe hit and conditional execution check ok. */
set_current_kprobe(p);
kcb->kprobe_status = KPROBE_HIT_ACTIVE;
/*
* If we have no pre-handler or it returned 0, we
* continue with normal processing. If we have a
* pre-handler and it returned non-zero, it prepped
* for calling the break_handler below on re-entry,
* so get out doing nothing more here.
*/
if (!p->pre_handler || !p->pre_handler(p, regs)) {
kcb->kprobe_status = KPROBE_HIT_SS;
singlestep(p, regs, kcb);
if (p->post_handler) {
kcb->kprobe_status = KPROBE_HIT_SSDONE;
p->post_handler(p, regs, 0);
}
reset_current_kprobe();
}
} else {
/*
* Probe hit but conditional execution check failed,
* so just skip the instruction and continue as if
* nothing had happened.
*/
singlestep_skip(p, regs);
}
} else if (cur) {
/* We probably hit a jprobe. Call its break handler. */
if (cur->break_handler && cur->break_handler(cur, regs)) {
kcb->kprobe_status = KPROBE_HIT_SS;
singlestep(cur, regs, kcb);
if (cur->post_handler) {
kcb->kprobe_status = KPROBE_HIT_SSDONE;
cur->post_handler(cur, regs, 0);
}
}
reset_current_kprobe();
} else {
/*
* The probe was removed and a race is in progress.
* There is nothing we can do about it. Let's restart
* the instruction. By the time we can restart, the
* real instruction will be there.
*/
}
}
/*
* Called with IRQs disabled. IRQs must remain disabled from that point
* all the way until processing this kprobe is complete. The current
* kprobes implementation cannot process more than one nested level of
* kprobe, and that level is reserved for user kprobe handlers, so we can't
* risk encountering a new kprobe in an interrupt handler.
*/
void __kprobes kprobe_handler(struct pt_regs *regs)
{
struct kprobe *p, *cur;
struct kprobe_ctlblk *kcb;
kprobe_opcode_t *addr = (kprobe_opcode_t *)regs->ARM_pc;
kcb = get_kprobe_ctlblk();
cur = kprobe_running();
p = get_kprobe(addr);
if (p) {
if (cur) {
/* Kprobe is pending, so we're recursing. */
switch (kcb->kprobe_status) {
case KPROBE_HIT_ACTIVE:
case KPROBE_HIT_SSDONE:
/* A pre- or post-handler probe got us here. */
kprobes_inc_nmissed_count(p);
save_previous_kprobe(kcb);
set_current_kprobe(p);
kcb->kprobe_status = KPROBE_REENTER;
singlestep(p, regs, kcb);
restore_previous_kprobe(kcb);
break;
default:
/* impossible cases */
BUG();
}
} else {
set_current_kprobe(p);
kcb->kprobe_status = KPROBE_HIT_ACTIVE;
/*
* If we have no pre-handler or it returned 0, we
* continue with normal processing. If we have a
* pre-handler and it returned non-zero, it prepped
* for calling the break_handler below on re-entry,
* so get out doing nothing more here.
*/
if (!p->pre_handler || !p->pre_handler(p, regs)) {
kcb->kprobe_status = KPROBE_HIT_SS;
singlestep(p, regs, kcb);
if (p->post_handler) {
kcb->kprobe_status = KPROBE_HIT_SSDONE;
p->post_handler(p, regs, 0);
}
reset_current_kprobe();
}
}
} else if (cur) {
/* We probably hit a jprobe. Call its break handler. */
if (cur->break_handler && cur->break_handler(cur, regs)) {
kcb->kprobe_status = KPROBE_HIT_SS;
singlestep(cur, regs, kcb);
if (cur->post_handler) {
kcb->kprobe_status = KPROBE_HIT_SSDONE;
cur->post_handler(cur, regs, 0);
}
}
reset_current_kprobe();
} else {
/*
* The probe was removed and a race is in progress.
* There is nothing we can do about it. Let's restart
* the instruction. By the time we can restart, the
* real instruction will be there.
*/
}
}
