/*JSON{
"type" : "staticmethod",
"class" : "Trig",
"name" : "getTrigger",
"generate" : "jswrap_trig_getTrigger",
"params" : [
["num","int","The trigger number (0..7)"]
],
"return" : ["JsVar","A structure containing all information about the trigger"]
}
Get the current state of a trigger
*/
JsVar *jswrap_trig_getTrigger(JsVarInt num) {
TriggerStruct *trig = &mainTrigger;
if (num<0 || num>=TRIGGER_TRIGGERS_COUNT) {
jsWarn("Invalid trigger number\n");
return 0;
}
TriggerPointStruct *tp = &trig->triggers[num];
// get offset in teeth
JsVarFloat position = tp->tooth + (tp->toothFraction/256.0);
// convert from teeth to degrees
position = wrapAround((position * 360 / trig->teethTotal) + trig->keyPosition, 360);
JsVar *obj = jsvNewWithFlags(JSV_OBJECT);
if (!obj) return 0;
JsVar *v;
v = jsvNewFromFloat(position);
jsvUnLock(jsvAddNamedChild(obj, v, "pos"));
jsvUnLock(v);
v = jsvNewFromFloat(jshGetMillisecondsFromTime(tp->pulseLength));
jsvUnLock(jsvAddNamedChild(obj, v, "pulseLength"));
jsvUnLock(v);
v = jsvNewWithFlags(JSV_ARRAY);
int i;
if (v) {
for (i=0;i<TRIGGERPOINT_TRIGGERS_COUNT;i++)
if (tp->pins[i] != PIN_UNDEFINED) {
jsvArrayPushAndUnLock(v, jsvNewFromPin(tp->pins[i]));
}
}
jsvUnLock(jsvAddNamedChild(obj, v, "pins"));
jsvUnLock(v);
return obj;
}
/*JSON{
"type" : "staticmethod",
"class" : "process",
"name" : "memory",
"generate" : "jswrap_process_memory",
"return" : ["JsVar","Information about memory usage"]
}
Run a Garbage Collection pass, and return an object containing information on memory usage.
* `free` : Memory that is available to be used (in blocks)
* `usage` : Memory that has been used (in blocks)
* `total` : Total memory (in blocks)
* `history` : Memory used for command history - that is freed if memory is low. Note that this is INCLUDED in the figure for 'free'
* `gc` : Memory freed during the GC pass
* `gctime` : Time taken for GC pass (in milliseconds)
* `stackEndAddress` : (on ARM) the address (that can be used with peek/poke/etc) of the END of the stack. The stack grows down, so unless you do a lot of recursion the bytes above this can be used.
* `flash_start` : (on ARM) the address of the start of flash memory (usually `0x8000000`)
* `flash_binary_end` : (on ARM) the address in flash memory of the end of Espruino's firmware.
* `flash_code_start` : (on ARM) the address in flash memory of pages that store any code that you save with `save()`.
* `flash_length` : (on ARM) the amount of flash memory this firmware was built for (in bytes). **Note:** Some STM32 chips actually have more memory than is advertised.
Memory units are specified in 'blocks', which are around 16 bytes each (depending on your device). See http://www.espruino.com/Performance for more information.
**Note:** To find free areas of flash memory, see `require('Flash').getFree()`
*/
JsVar *jswrap_process_memory() {
JsSysTime time1 = jshGetSystemTime();
int gc = jsvGarbageCollect();
JsSysTime time2 = jshGetSystemTime();
JsVar *obj = jsvNewObject();
if (obj) {
unsigned int history = 0;
JsVar *historyVar = jsvObjectGetChild(execInfo.hiddenRoot, JSI_HISTORY_NAME, 0);
if (historyVar) {
history = (unsigned int)jsvCountJsVarsUsed(historyVar); // vars used to store history
jsvUnLock(historyVar);
}
unsigned int usage = jsvGetMemoryUsage() - history;
unsigned int total = jsvGetMemoryTotal();
jsvObjectSetChildAndUnLock(obj, "free", jsvNewFromInteger((JsVarInt)(total-usage)));
jsvObjectSetChildAndUnLock(obj, "usage", jsvNewFromInteger((JsVarInt)usage));
jsvObjectSetChildAndUnLock(obj, "total", jsvNewFromInteger((JsVarInt)total));
jsvObjectSetChildAndUnLock(obj, "history", jsvNewFromInteger((JsVarInt)history));
jsvObjectSetChildAndUnLock(obj, "gc", jsvNewFromInteger((JsVarInt)gc));
jsvObjectSetChildAndUnLock(obj, "gctime", jsvNewFromFloat(jshGetMillisecondsFromTime(time2-time1)));
#ifdef ARM
extern uint32_t LINKER_END_VAR; // end of ram used (variables) - should be 'void', but 'int' avoids warnings
extern uint32_t LINKER_ETEXT_VAR; // end of flash text (binary) section - should be 'void', but 'int' avoids warnings
jsvObjectSetChildAndUnLock(obj, "stackEndAddress", jsvNewFromInteger((JsVarInt)(unsigned int)&LINKER_END_VAR));
jsvObjectSetChildAndUnLock(obj, "flash_start", jsvNewFromInteger((JsVarInt)FLASH_START));
jsvObjectSetChildAndUnLock(obj, "flash_binary_end", jsvNewFromInteger((JsVarInt)(unsigned int)&LINKER_ETEXT_VAR));
jsvObjectSetChildAndUnLock(obj, "flash_code_start", jsvNewFromInteger((JsVarInt)FLASH_SAVED_CODE_START));
jsvObjectSetChildAndUnLock(obj, "flash_length", jsvNewFromInteger((JsVarInt)FLASH_TOTAL));
#endif
}
return obj;
}
