/**
* M106: Set Fan Speed
*
* S<int> Speed between 0-255
* P<index> Fan index, if more than one fan
*
* With EXTRA_FAN_SPEED enabled:
*
* T<int> Restore/Use/Set Temporary Speed:
* 1 = Restore previous speed after T2
* 2 = Use temporary speed set with T3-255
* 3-255 = Set the speed for use with T2
*/
void GcodeSuite::M106() {
const uint8_t p = parser.byteval('P');
if (p < FAN_COUNT) {
#if ENABLED(EXTRA_FAN_SPEED)
const int16_t t = parser.intval('T');
NOMORE(t, 255);
if (t > 0) {
switch (t) {
case 1:
fanSpeeds[p] = old_fanSpeeds[p];
break;
case 2:
old_fanSpeeds[p] = fanSpeeds[p];
fanSpeeds[p] = new_fanSpeeds[p];
break;
default:
new_fanSpeeds[p] = t;
break;
}
return;
}
#endif // EXTRA_FAN_SPEED
const uint16_t s = parser.ushortval('S', 255);
fanSpeeds[p] = min(s, 255);
}
}
void lcd_mixer_gradient_z_end_edit() {
ui.defer_status_screen(true);
ui.encoder_direction_normal();
ENCODER_RATE_MULTIPLY(true);
if (ui.encoderPosition != 0) {
mixer.gradient.end_z += float((int)ui.encoderPosition) * 0.1;
ui.encoderPosition = 0;
NOLESS(mixer.gradient.end_z, 0);
NOMORE(mixer.gradient.end_z, Z_MAX_POS);
}
if (ui.should_draw()) {
char tmp[21];
sprintf_P(tmp, PSTR(MSG_END_Z ": %4d.%d mm"), int(mixer.gradient.end_z), int(mixer.gradient.end_z * 10) % 10);
SETCURSOR(2, (LCD_HEIGHT - 1) / 2);
LCDPRINT(tmp);
}
if (ui.lcd_clicked) {
if (mixer.gradient.end_z < mixer.gradient.start_z)
mixer.gradient.start_z = mixer.gradient.end_z;
mixer.refresh_gradient();
ui.goto_previous_screen();
}
}
void dac_current_raw(uint8_t channel, uint16_t val) {
if (!dac_present) return;
NOMORE(val, DAC_STEPPER_MAX);
mcp4728_analogWrite(dac_order[channel], val);
mcp4728_simpleCommand(UPDATE);
}
void dac_current_percent(uint8_t channel, float val) {
if (!dac_present) return;
NOMORE(val, 100);
mcp4728_analogWrite(dac_order[channel], val * 0.01 * (DAC_STEPPER_MAX));
mcp4728_simpleCommand(UPDATE);
}
FORCE_INLINE unsigned short calc_timer(unsigned short step_rate) {
unsigned short timer;
NOMORE(step_rate, MAX_STEP_FREQUENCY);
if (step_rate > 20000) { // If steprate > 20kHz >> step 4 times
step_rate = (step_rate >> 2) & 0x3fff;
step_loops = 4;
}
FORCE_INLINE unsigned short calc_timer(unsigned short step_rate) {
unsigned short timer;
NOMORE(step_rate, MAX_STEP_FREQUENCY);
if(step_rate > (2 * DOUBLE_STEP_FREQUENCY)) { // If steprate > 2*DOUBLE_STEP_FREQUENCY >> step 4 times
step_rate >>= 2;
step_loops = 4;
}
/**
* M113: Get or set Host Keepalive interval (0 to disable)
*
* S<seconds> Optional. Set the keepalive interval.
*/
void GcodeSuite::M113() {
if (parser.seenval('S')) {
host_keepalive_interval = parser.value_byte();
NOMORE(host_keepalive_interval, 60);
}
else {
SERIAL_ECHO_START();
SERIAL_ECHOLNPAIR("M113 S", (unsigned long)host_keepalive_interval);
}
}
void Laser::fire(float intensity/*=100.0*/){
laser.firing = LASER_ON;
laser.last_firing = micros(); // microseconds of last laser firing
NOMORE(intensity, 100.0);
NOLESS(intensity, 0.0);
#if ENABLED(LASER_PWM_INVERT)
intensity = 100 - intensity;
#endif
#if LASER_CONTROL == 1
#if LASER_PWR_PIN == 2
OCR3B = PWM_MAPPED_INTENSITY;
#elif LASER_PWR_PIN == 3
OCR3C = PWM_MAPPED_INTENSITY;
#elif LASER_PWR_PIN == 5
OCR3A = PWM_MAPPED_INTENSITY;
#elif LASER_PWR_PIN == 6
OCR4A = PWM_MAPPED_INTENSITY;
#elif LASER_PWR_PIN == 7
OCR4B = PWM_MAPPED_INTENSITY;
#elif LASER_PWR_PIN == 8
OCR4C = PWM_MAPPED_INTENSITY;
#endif
#elif LASER_CONTROL == 2
#if LASER_PWM_PIN == 2
OCR3B = PWM_MAPPED_INTENSITY;
#elif LASER_PWM_PIN == 3
OCR3C = PWM_MAPPED_INTENSITY;
#elif LASER_PWM_PIN == 5
OCR3A = PWM_MAPPED_INTENSITY;
#elif LASER_PWM_PIN == 6
OCR4A = PWM_MAPPED_INTENSITY;
#elif LASER_PWM_PIN == 7
OCR4B = PWM_MAPPED_INTENSITY;
#elif LASER_PWM_PIN == 8
OCR4C = PWM_MAPPED_INTENSITY;
#endif
WRITE(LASER_PWR_PIN, LASER_ARM);
#endif /* LASER_CONTROL */
if (laser.diagnostics) SERIAL_EM("Laser_byte fired");
}
void Mixer::update_gradient_for_z(const float z) {
if (z == prev_z) return;
prev_z = z;
const float slice = gradient.end_z - gradient.start_z;
float pct = (z - gradient.start_z) / slice;
NOLESS(pct, 0.0f); NOMORE(pct, 1.0f);
MIXER_STEPPER_LOOP(i) {
const mixer_perc_t sm = gradient.start_mix[i];
mix[i] = sm + (gradient.end_mix[i] - sm) * pct;
}
copy_mix_to_color(gradient.color);
}
/**
* Perform a tool-change, which may result in moving the
* previous tool out of the way and the new tool into place.
*/
void tool_change(const uint8_t tmp_extruder, const float fr_mm_s/*=0.0*/, bool no_move/*=false*/) {
#if ENABLED(MIXING_EXTRUDER)
UNUSED(fr_mm_s); UNUSED(no_move);
if (tmp_extruder >= MIXING_VIRTUAL_TOOLS)
return invalid_extruder_error(tmp_extruder);
#if MIXING_VIRTUAL_TOOLS > 1
// T0-Tnnn: Switch virtual tool by changing the index to the mix
mixer.T(tmp_extruder);
#endif
#elif ENABLED(PRUSA_MMU2)
UNUSED(fr_mm_s); UNUSED(no_move);
mmu2.toolChange(tmp_extruder);
#elif EXTRUDERS < 2
UNUSED(fr_mm_s); UNUSED(no_move);
if (tmp_extruder) invalid_extruder_error(tmp_extruder);
return;
#else // EXTRUDERS > 1
planner.synchronize();
#if ENABLED(DUAL_X_CARRIAGE) // Only T0 allowed if the Printer is in DXC_DUPLICATION_MODE or DXC_MIRRORED_MODE
if (tmp_extruder != 0 && dxc_is_duplicating())
return invalid_extruder_error(tmp_extruder);
#endif
#if HAS_LEVELING
// Set current position to the physical position
const bool leveling_was_active = planner.leveling_active;
set_bed_leveling_enabled(false);
#endif
if (tmp_extruder >= EXTRUDERS)
return invalid_extruder_error(tmp_extruder);
if (!no_move && !all_axes_homed()) {
no_move = true;
if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("No move on toolchange");
}
#if HAS_LCD_MENU
ui.return_to_status();
#endif
#if ENABLED(TOOLCHANGE_FILAMENT_SWAP)
const bool should_swap = !no_move && toolchange_settings.swap_length;
#if ENABLED(PREVENT_COLD_EXTRUSION)
const bool too_cold = !DEBUGGING(DRYRUN) && (thermalManager.targetTooColdToExtrude(active_extruder) || thermalManager.targetTooColdToExtrude(tmp_extruder));
#else
constexpr bool too_cold = false;
#endif
if (should_swap) {
if (too_cold) {
SERIAL_ECHO_MSG(MSG_ERR_HOTEND_TOO_COLD);
#if ENABLED(SINGLENOZZLE)
active_extruder = tmp_extruder;
return;
#endif
}
else {
#if ENABLED(ADVANCED_PAUSE_FEATURE)
do_pause_e_move(-toolchange_settings.swap_length, MMM_TO_MMS(toolchange_settings.retract_speed));
#else
current_position[E_AXIS] -= toolchange_settings.swap_length / planner.e_factor[active_extruder];
planner.buffer_line(current_position, MMM_TO_MMS(toolchange_settings.retract_speed), active_extruder);
#endif
}
}
#endif // TOOLCHANGE_FILAMENT_SWAP
if (tmp_extruder != active_extruder) {
#if SWITCHING_NOZZLE_TWO_SERVOS
raise_nozzle(active_extruder);
#endif
const float old_feedrate_mm_s = fr_mm_s > 0.0 ? fr_mm_s : feedrate_mm_s;
feedrate_mm_s = fr_mm_s > 0.0 ? fr_mm_s : XY_PROBE_FEEDRATE_MM_S;
#if HAS_SOFTWARE_ENDSTOPS && ENABLED(DUAL_X_CARRIAGE)
update_software_endstops(X_AXIS, active_extruder, tmp_extruder);
#endif
set_destination_from_current();
if (!no_move) {
#if DISABLED(SWITCHING_NOZZLE)
// Do a small lift to avoid the workpiece in the move back (below)
#if ENABLED(TOOLCHANGE_PARK)
current_position[X_AXIS] = toolchange_settings.change_point.x;
current_position[Y_AXIS] = toolchange_settings.change_point.y;
#endif
current_position[Z_AXIS] += toolchange_settings.z_raise;
#if HAS_SOFTWARE_ENDSTOPS
NOMORE(current_position[Z_AXIS], soft_endstop[Z_AXIS].max);
#endif
planner.buffer_line(current_position, feedrate_mm_s, active_extruder);
#endif
planner.synchronize();
}
#if HAS_HOTEND_OFFSET
#if ENABLED(DUAL_X_CARRIAGE)
constexpr float xdiff = 0;
#else
const float xdiff = hotend_offset[X_AXIS][tmp_extruder] - hotend_offset[X_AXIS][active_extruder];
#endif
const float ydiff = hotend_offset[Y_AXIS][tmp_extruder] - hotend_offset[Y_AXIS][active_extruder],
zdiff = hotend_offset[Z_AXIS][tmp_extruder] - hotend_offset[Z_AXIS][active_extruder];
#else
constexpr float xdiff = 0, ydiff = 0, zdiff = 0;
#endif
#if ENABLED(DUAL_X_CARRIAGE)
dualx_tool_change(tmp_extruder, no_move);
#elif ENABLED(PARKING_EXTRUDER) // Dual Parking extruder
parking_extruder_tool_change(tmp_extruder, no_move);
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER) // Magnetic Parking extruder
magnetic_parking_extruder_tool_change(tmp_extruder);
#elif ENABLED(SWITCHING_TOOLHEAD) // Switching Toolhead
switching_toolhead_tool_change(tmp_extruder, fr_mm_s, no_move);
#elif ENABLED(SWITCHING_NOZZLE) && !SWITCHING_NOZZLE_TWO_SERVOS
// Raise by a configured distance to avoid workpiece, except with
// SWITCHING_NOZZLE_TWO_SERVOS, as both nozzles will lift instead.
current_position[Z_AXIS] += MAX(-zdiff, 0.0) + toolchange_settings.z_raise;
#if HAS_SOFTWARE_ENDSTOPS
NOMORE(current_position[Z_AXIS], soft_endstop[Z_AXIS].max);
#endif
if (!no_move) fast_line_to_current(Z_AXIS);
move_nozzle_servo(tmp_extruder);
#endif
if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR("Offset Tool XY by { ", xdiff, ", ", ydiff, ", ", zdiff, " }");
// The newly-selected extruder XY is actually at...
current_position[X_AXIS] += xdiff;
current_position[Y_AXIS] += ydiff;
current_position[Z_AXIS] += zdiff;
// Set the new active extruder if not already done in tool specific function above
active_extruder = tmp_extruder;
// Tell the planner the new "current position"
sync_plan_position();
#if ENABLED(DELTA)
//LOOP_XYZ(i) update_software_endstops(i); // or modify the constrain function
const bool safe_to_move = current_position[Z_AXIS] < delta_clip_start_height - 1;
#else
constexpr bool safe_to_move = true;
#endif
// Return to position and lower again
if (safe_to_move && !no_move && IsRunning()) {
if (DEBUGGING(LEVELING)) DEBUG_POS("Move back", destination);
#if ENABLED(SINGLENOZZLE)
#if FAN_COUNT > 0
singlenozzle_fan_speed[active_extruder] = thermalManager.fan_speed[0];
thermalManager.fan_speed[0] = singlenozzle_fan_speed[tmp_extruder];
#endif
singlenozzle_temp[active_extruder] = thermalManager.temp_hotend[0].target;
if (singlenozzle_temp[tmp_extruder] && singlenozzle_temp[tmp_extruder] != singlenozzle_temp[active_extruder]) {
thermalManager.setTargetHotend(singlenozzle_temp[tmp_extruder], 0);
#if EITHER(ULTRA_LCD, EXTENSIBLE_UI)
thermalManager.set_heating_message(0);
#endif
(void)thermalManager.wait_for_hotend(0, false); // Wait for heating or cooling
}
active_extruder = tmp_extruder;
#endif
#if ENABLED(TOOLCHANGE_FILAMENT_SWAP)
if (should_swap && !too_cold) {
#if ENABLED(ADVANCED_PAUSE_FEATURE)
do_pause_e_move(toolchange_settings.swap_length + TOOLCHANGE_FIL_EXTRA_PRIME, toolchange_settings.prime_speed);
#else
current_position[E_AXIS] += (toolchange_settings.swap_length + TOOLCHANGE_FIL_EXTRA_PRIME) / planner.e_factor[tmp_extruder];
planner.buffer_line(current_position, toolchange_settings.prime_speed, tmp_extruder);
#endif
planner.synchronize();
#if TOOLCHANGE_FIL_EXTRA_PRIME
planner.set_e_position_mm((destination[E_AXIS] = current_position[E_AXIS] = current_position[E_AXIS] - (TOOLCHANGE_FIL_EXTRA_PRIME)));
#endif
}
#endif
// Prevent a move outside physical bounds
apply_motion_limits(destination);
// Move back to the original (or tweaked) position
do_blocking_move_to(destination);
#if ENABLED(DUAL_X_CARRIAGE)
active_extruder_parked = false;
#endif
feedrate_mm_s = old_feedrate_mm_s;
}
#if ENABLED(SWITCHING_NOZZLE)
else {
// Move back down. (Including when the new tool is higher.)
do_blocking_move_to_z(destination[Z_AXIS], planner.settings.max_feedrate_mm_s[Z_AXIS]);
}
#endif
#if ENABLED(PRUSA_MMU2)
mmu2.toolChange(tmp_extruder);
#endif
#if SWITCHING_NOZZLE_TWO_SERVOS
lower_nozzle(active_extruder);
#endif
#if ENABLED(TOOLCHANGE_FILAMENT_SWAP) && ADVANCED_PAUSE_RESUME_PRIME != 0
if (should_swap && !too_cold) {
const float resume_eaxis = current_position[E_AXIS];
#if ENABLED(ADVANCED_PAUSE_FEATURE)
do_pause_e_move(toolchange_settings.swap_length, toolchange_settings.prime_speed);
#else
current_position[E_AXIS] += (ADVANCED_PAUSE_RESUME_PRIME) / planner.e_factor[active_extruder];
planner.buffer_line(current_position, ADVANCED_PAUSE_PURGE_FEEDRATE, active_extruder);
#endif
planner.synchronize();
planner.set_e_position_mm((destination[E_AXIS] = current_position[E_AXIS] = resume_eaxis));
}
#endif
} // (tmp_extruder != active_extruder)
planner.synchronize();
#if ENABLED(EXT_SOLENOID) && DISABLED(PARKING_EXTRUDER)
disable_all_solenoids();
enable_solenoid_on_active_extruder();
#endif
#if ENABLED(MK2_MULTIPLEXER)
if (tmp_extruder >= E_STEPPERS) return invalid_extruder_error(tmp_extruder);
select_multiplexed_stepper(tmp_extruder);
#endif
#if DO_SWITCH_EXTRUDER
planner.synchronize();
move_extruder_servo(active_extruder);
#endif
#if HAS_FANMUX
fanmux_switch(active_extruder);
#endif
#if HAS_LEVELING
// Restore leveling to re-establish the logical position
set_bed_leveling_enabled(leveling_was_active);
#endif
SERIAL_ECHO_START();
SERIAL_ECHOLNPAIR(MSG_ACTIVE_EXTRUDER, int(active_extruder));
#endif // EXTRUDERS > 1
}
/**
* M48: Z probe repeatability measurement function.
*
* Usage:
* M48 <P#> <X#> <Y#> <V#> <E> <L#> <S>
* P = Number of sampled points (4-50, default 10)
* X = Sample X position
* Y = Sample Y position
* V = Verbose level (0-4, default=1)
* E = Engage Z probe for each reading
* L = Number of legs of movement before probe
* S = Schizoid (Or Star if you prefer)
*
* This function requires the machine to be homed before invocation.
*/
void GcodeSuite::M48() {
if (axis_unhomed_error()) return;
const int8_t verbose_level = parser.byteval('V', 1);
if (!WITHIN(verbose_level, 0, 4)) {
SERIAL_ECHOLNPGM("?(V)erbose level is implausible (0-4).");
return;
}
if (verbose_level > 0)
SERIAL_ECHOLNPGM("M48 Z-Probe Repeatability Test");
const int8_t n_samples = parser.byteval('P', 10);
if (!WITHIN(n_samples, 4, 50)) {
SERIAL_ECHOLNPGM("?Sample size not plausible (4-50).");
return;
}
const ProbePtRaise raise_after = parser.boolval('E') ? PROBE_PT_STOW : PROBE_PT_RAISE;
float X_current = current_position[X_AXIS],
Y_current = current_position[Y_AXIS];
const float X_probe_location = parser.linearval('X', X_current + X_PROBE_OFFSET_FROM_EXTRUDER),
Y_probe_location = parser.linearval('Y', Y_current + Y_PROBE_OFFSET_FROM_EXTRUDER);
if (!position_is_reachable_by_probe(X_probe_location, Y_probe_location)) {
SERIAL_ECHOLNPGM("? (X,Y) out of bounds.");
return;
}
bool seen_L = parser.seen('L');
uint8_t n_legs = seen_L ? parser.value_byte() : 0;
if (n_legs > 15) {
SERIAL_ECHOLNPGM("?Number of legs in movement not plausible (0-15).");
return;
}
if (n_legs == 1) n_legs = 2;
const bool schizoid_flag = parser.boolval('S');
if (schizoid_flag && !seen_L) n_legs = 7;
/**
* Now get everything to the specified probe point So we can safely do a
* probe to get us close to the bed. If the Z-Axis is far from the bed,
* we don't want to use that as a starting point for each probe.
*/
if (verbose_level > 2)
SERIAL_ECHOLNPGM("Positioning the probe...");
// Disable bed level correction in M48 because we want the raw data when we probe
#if HAS_LEVELING
const bool was_enabled = planner.leveling_active;
set_bed_leveling_enabled(false);
#endif
setup_for_endstop_or_probe_move();
float mean = 0.0, sigma = 0.0, min = 99999.9, max = -99999.9, sample_set[n_samples];
// Move to the first point, deploy, and probe
const float t = probe_pt(X_probe_location, Y_probe_location, raise_after, verbose_level);
bool probing_good = !isnan(t);
if (probing_good) {
randomSeed(millis());
for (uint8_t n = 0; n < n_samples; n++) {
if (n_legs) {
const int dir = (random(0, 10) > 5.0) ? -1 : 1; // clockwise or counter clockwise
float angle = random(0, 360);
const float radius = random(
#if ENABLED(DELTA)
(int) (0.1250000000 * (DELTA_PRINTABLE_RADIUS)),
(int) (0.3333333333 * (DELTA_PRINTABLE_RADIUS))
#else
(int) 5.0, (int) (0.125 * MIN(X_BED_SIZE, Y_BED_SIZE))
#endif
);
if (verbose_level > 3) {
SERIAL_ECHOPAIR("Starting radius: ", radius);
SERIAL_ECHOPAIR(" angle: ", angle);
SERIAL_ECHOPGM(" Direction: ");
if (dir > 0) SERIAL_ECHOPGM("Counter-");
SERIAL_ECHOLNPGM("Clockwise");
}
for (uint8_t l = 0; l < n_legs - 1; l++) {
float delta_angle;
if (schizoid_flag)
// The points of a 5 point star are 72 degrees apart. We need to
// skip a point and go to the next one on the star.
delta_angle = dir * 2.0 * 72.0;
else
// If we do this line, we are just trying to move further
// around the circle.
delta_angle = dir * (float) random(25, 45);
angle += delta_angle;
while (angle > 360.0) // We probably do not need to keep the angle between 0 and 2*PI, but the
angle -= 360.0; // Arduino documentation says the trig functions should not be given values
while (angle < 0.0) // outside of this range. It looks like they behave correctly with
angle += 360.0; // numbers outside of the range, but just to be safe we clamp them.
X_current = X_probe_location - (X_PROBE_OFFSET_FROM_EXTRUDER) + cos(RADIANS(angle)) * radius;
Y_current = Y_probe_location - (Y_PROBE_OFFSET_FROM_EXTRUDER) + sin(RADIANS(angle)) * radius;
#if DISABLED(DELTA)
X_current = constrain(X_current, X_MIN_POS, X_MAX_POS);
Y_current = constrain(Y_current, Y_MIN_POS, Y_MAX_POS);
#else
// If we have gone out too far, we can do a simple fix and scale the numbers
// back in closer to the origin.
while (!position_is_reachable_by_probe(X_current, Y_current)) {
X_current *= 0.8;
Y_current *= 0.8;
if (verbose_level > 3) {
SERIAL_ECHOPAIR("Pulling point towards center:", X_current);
SERIAL_ECHOLNPAIR(", ", Y_current);
}
}
#endif
if (verbose_level > 3) {
SERIAL_ECHOPGM("Going to:");
SERIAL_ECHOPAIR(" X", X_current);
SERIAL_ECHOPAIR(" Y", Y_current);
SERIAL_ECHOLNPAIR(" Z", current_position[Z_AXIS]);
}
do_blocking_move_to_xy(X_current, Y_current);
} // n_legs loop
} // n_legs
// Probe a single point
sample_set[n] = probe_pt(X_probe_location, Y_probe_location, raise_after, 0);
// Break the loop if the probe fails
probing_good = !isnan(sample_set[n]);
if (!probing_good) break;
/**
* Get the current mean for the data points we have so far
*/
float sum = 0.0;
for (uint8_t j = 0; j <= n; j++) sum += sample_set[j];
mean = sum / (n + 1);
NOMORE(min, sample_set[n]);
NOLESS(max, sample_set[n]);
/**
* Now, use that mean to calculate the standard deviation for the
* data points we have so far
*/
sum = 0.0;
for (uint8_t j = 0; j <= n; j++)
sum += sq(sample_set[j] - mean);
sigma = SQRT(sum / (n + 1));
if (verbose_level > 0) {
if (verbose_level > 1) {
SERIAL_ECHO(n + 1);
SERIAL_ECHOPAIR(" of ", (int)n_samples);
SERIAL_ECHOPAIR_F(": z: ", sample_set[n], 3);
if (verbose_level > 2) {
SERIAL_ECHOPAIR_F(" mean: ", mean, 4);
SERIAL_ECHOPAIR_F(" sigma: ", sigma, 6);
SERIAL_ECHOPAIR_F(" min: ", min, 3);
SERIAL_ECHOPAIR_F(" max: ", max, 3);
SERIAL_ECHOPAIR_F(" range: ", max-min, 3);
}
SERIAL_EOL();
}
}
} // n_samples loop
}
STOW_PROBE();
if (probing_good) {
SERIAL_ECHOLNPGM("Finished!");
if (verbose_level > 0) {
SERIAL_ECHOPAIR_F("Mean: ", mean, 6);
SERIAL_ECHOPAIR_F(" Min: ", min, 3);
SERIAL_ECHOPAIR_F(" Max: ", max, 3);
SERIAL_ECHOLNPAIR_F(" Range: ", max-min, 3);
}
SERIAL_ECHOLNPAIR_F("Standard Deviation: ", sigma, 6);
SERIAL_EOL();
}
clean_up_after_endstop_or_probe_move();
// Re-enable bed level correction if it had been on
#if HAS_LEVELING
set_bed_leveling_enabled(was_enabled);
#endif
report_current_position();
}
/**
* M420: Enable/Disable Bed Leveling and/or set the Z fade height.
*
* S[bool] Turns leveling on or off
* Z[height] Sets the Z fade height (0 or none to disable)
* V[bool] Verbose - Print the leveling grid
*
* With AUTO_BED_LEVELING_UBL only:
*
* L[index] Load UBL mesh from index (0 is default)
* T[map] 0:Human-readable 1:CSV 2:"LCD" 4:Compact
*
* With mesh-based leveling only:
*
* C Center mesh on the mean of the lowest and highest
*
* With MARLIN_DEV_MODE:
* S2 Create a simple random mesh and enable
*/
void GcodeSuite::M420() {
const bool seen_S = parser.seen('S'),
to_enable = seen_S ? parser.value_bool() : planner.leveling_active;
#if ENABLED(MARLIN_DEV_MODE)
if (parser.intval('S') == 2) {
#if ENABLED(AUTO_BED_LEVELING_BILINEAR)
bilinear_start[X_AXIS] = MIN_PROBE_X;
bilinear_start[Y_AXIS] = MIN_PROBE_Y;
bilinear_grid_spacing[X_AXIS] = (MAX_PROBE_X - (MIN_PROBE_X)) / (GRID_MAX_POINTS_X - 1);
bilinear_grid_spacing[Y_AXIS] = (MAX_PROBE_Y - (MIN_PROBE_Y)) / (GRID_MAX_POINTS_Y - 1);
#endif
for (uint8_t x = 0; x < GRID_MAX_POINTS_X; x++)
for (uint8_t y = 0; y < GRID_MAX_POINTS_Y; y++)
Z_VALUES(x, y) = 0.001 * random(-200, 200);
SERIAL_ECHOPGM("Simulated " STRINGIFY(GRID_MAX_POINTS_X) "x" STRINGIFY(GRID_MAX_POINTS_X) " mesh ");
SERIAL_ECHOPAIR(" (", MIN_PROBE_X);
SERIAL_CHAR(','); SERIAL_ECHO(MIN_PROBE_Y);
SERIAL_ECHOPAIR(")-(", MAX_PROBE_X);
SERIAL_CHAR(','); SERIAL_ECHO(MAX_PROBE_Y);
SERIAL_ECHOLNPGM(")");
}
#endif
// If disabling leveling do it right away
// (Don't disable for just M420 or M420 V)
if (seen_S && !to_enable) set_bed_leveling_enabled(false);
const float oldpos[] = { current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS] };
#if ENABLED(AUTO_BED_LEVELING_UBL)
// L to load a mesh from the EEPROM
if (parser.seen('L')) {
set_bed_leveling_enabled(false);
#if ENABLED(EEPROM_SETTINGS)
const int8_t storage_slot = parser.has_value() ? parser.value_int() : ubl.storage_slot;
const int16_t a = settings.calc_num_meshes();
if (!a) {
SERIAL_ECHOLNPGM("?EEPROM storage not available.");
return;
}
if (!WITHIN(storage_slot, 0, a - 1)) {
SERIAL_ECHOLNPGM("?Invalid storage slot.");
SERIAL_ECHOLNPAIR("?Use 0 to ", a - 1);
return;
}
settings.load_mesh(storage_slot);
ubl.storage_slot = storage_slot;
#else
SERIAL_ECHOLNPGM("?EEPROM storage not available.");
return;
#endif
}
// L or V display the map info
if (parser.seen('L') || parser.seen('V')) {
ubl.display_map(parser.byteval('T'));
SERIAL_ECHOPGM("Mesh is ");
if (!ubl.mesh_is_valid()) SERIAL_ECHOPGM("in");
SERIAL_ECHOLNPAIR("valid\nStorage slot: ", ubl.storage_slot);
}
#endif // AUTO_BED_LEVELING_UBL
const bool seenV = parser.seen('V');
#if HAS_MESH
if (leveling_is_valid()) {
// Subtract the given value or the mean from all mesh values
if (parser.seen('C')) {
const float cval = parser.value_float();
#if ENABLED(AUTO_BED_LEVELING_UBL)
set_bed_leveling_enabled(false);
ubl.adjust_mesh_to_mean(true, cval);
#else
#if ENABLED(M420_C_USE_MEAN)
// Get the sum and average of all mesh values
float mesh_sum = 0;
for (uint8_t x = GRID_MAX_POINTS_X; x--;)
for (uint8_t y = GRID_MAX_POINTS_Y; y--;)
mesh_sum += Z_VALUES(x, y);
const float zmean = mesh_sum / float(GRID_MAX_POINTS);
#else
// Find the low and high mesh values
float lo_val = 100, hi_val = -100;
for (uint8_t x = GRID_MAX_POINTS_X; x--;)
for (uint8_t y = GRID_MAX_POINTS_Y; y--;) {
const float z = Z_VALUES(x, y);
NOMORE(lo_val, z);
NOLESS(hi_val, z);
}
// Take the mean of the lowest and highest
const float zmean = (lo_val + hi_val) / 2.0 + cval;
#endif
// If not very close to 0, adjust the mesh
if (!NEAR_ZERO(zmean)) {
set_bed_leveling_enabled(false);
// Subtract the mean from all values
for (uint8_t x = GRID_MAX_POINTS_X; x--;)
for (uint8_t y = GRID_MAX_POINTS_Y; y--;)
Z_VALUES(x, y) -= zmean;
#if ENABLED(ABL_BILINEAR_SUBDIVISION)
bed_level_virt_interpolate();
#endif
}
#endif
}
}
else if (to_enable || seenV) {
SERIAL_ECHO_MSG("Invalid mesh.");
goto EXIT_M420;
}
#endif // HAS_MESH
// V to print the matrix or mesh
if (seenV) {
#if ABL_PLANAR
planner.bed_level_matrix.debug(PSTR("Bed Level Correction Matrix:"));
#else
if (leveling_is_valid()) {
#if ENABLED(AUTO_BED_LEVELING_BILINEAR)
print_bilinear_leveling_grid();
#if ENABLED(ABL_BILINEAR_SUBDIVISION)
print_bilinear_leveling_grid_virt();
#endif
#elif ENABLED(MESH_BED_LEVELING)
SERIAL_ECHOLNPGM("Mesh Bed Level data:");
mbl.report_mesh();
#endif
}
#endif
}
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
if (parser.seen('Z')) set_z_fade_height(parser.value_linear_units(), false);
#endif
// Enable leveling if specified, or if previously active
set_bed_leveling_enabled(to_enable);
#if HAS_MESH
EXIT_M420:
#endif
// Error if leveling failed to enable or reenable
if (to_enable && !planner.leveling_active)
SERIAL_ERROR_MSG(MSG_ERR_M420_FAILED);
SERIAL_ECHO_START();
SERIAL_ECHOPGM("Bed Leveling ");
serialprintln_onoff(planner.leveling_active);
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
SERIAL_ECHO_START();
SERIAL_ECHOPGM("Fade Height ");
if (planner.z_fade_height > 0.0)
SERIAL_ECHOLN(planner.z_fade_height);
else
SERIAL_ECHOLNPGM(MSG_OFF);
#endif
// Report change in position
if (memcmp(oldpos, current_position, sizeof(oldpos)))
report_current_position();
}
bool _O2 unified_bed_leveling::prepare_segmented_line_to(const float (&rtarget)[XYZE], const float &feedrate) {
if (!position_is_reachable(rtarget[X_AXIS], rtarget[Y_AXIS])) // fail if moving outside reachable boundary
return true; // did not move, so current_position still accurate
const float total[XYZE] = {
rtarget[X_AXIS] - current_position[X_AXIS],
rtarget[Y_AXIS] - current_position[Y_AXIS],
rtarget[Z_AXIS] - current_position[Z_AXIS],
rtarget[E_AXIS] - current_position[E_AXIS]
};
const float cartesian_xy_mm = HYPOT(total[X_AXIS], total[Y_AXIS]); // total horizontal xy distance
#if IS_KINEMATIC
const float seconds = cartesian_xy_mm / feedrate; // seconds to move xy distance at requested rate
uint16_t segments = lroundf(delta_segments_per_second * seconds), // preferred number of segments for distance @ feedrate
seglimit = lroundf(cartesian_xy_mm * (1.0f / (DELTA_SEGMENT_MIN_LENGTH))); // number of segments at minimum segment length
NOMORE(segments, seglimit); // limit to minimum segment length (fewer segments)
#else
uint16_t segments = lroundf(cartesian_xy_mm * (1.0f / (DELTA_SEGMENT_MIN_LENGTH))); // cartesian fixed segment length
#endif
NOLESS(segments, 1U); // must have at least one segment
const float inv_segments = 1.0f / segments; // divide once, multiply thereafter
#if IS_SCARA // scale the feed rate from mm/s to degrees/s
scara_feed_factor = cartesian_xy_mm * inv_segments * feedrate;
scara_oldA = planner.get_axis_position_degrees(A_AXIS);
scara_oldB = planner.get_axis_position_degrees(B_AXIS);
#endif
const float diff[XYZE] = {
total[X_AXIS] * inv_segments,
total[Y_AXIS] * inv_segments,
total[Z_AXIS] * inv_segments,
total[E_AXIS] * inv_segments
};
// Note that E segment distance could vary slightly as z mesh height
// changes for each segment, but small enough to ignore.
float raw[XYZE] = {
current_position[X_AXIS],
current_position[Y_AXIS],
current_position[Z_AXIS],
current_position[E_AXIS]
};
// Only compute leveling per segment if ubl active and target below z_fade_height.
if (!planner.leveling_active || !planner.leveling_active_at_z(rtarget[Z_AXIS])) { // no mesh leveling
while (--segments) {
LOOP_XYZE(i) raw[i] += diff[i];
ubl_buffer_segment_raw(raw, feedrate);
}
ubl_buffer_segment_raw(rtarget, feedrate);
return false; // moved but did not set_current_from_destination();
}
// Otherwise perform per-segment leveling
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
const float fade_scaling_factor = planner.fade_scaling_factor_for_z(rtarget[Z_AXIS]);
#endif
// increment to first segment destination
LOOP_XYZE(i) raw[i] += diff[i];
for (;;) { // for each mesh cell encountered during the move
// Compute mesh cell invariants that remain constant for all segments within cell.
// Note for cell index, if point is outside the mesh grid (in MESH_INSET perimeter)
// the bilinear interpolation from the adjacent cell within the mesh will still work.
// Inner loop will exit each time (because out of cell bounds) but will come back
// in top of loop and again re-find same adjacent cell and use it, just less efficient
// for mesh inset area.
int8_t cell_xi = (raw[X_AXIS] - (MESH_MIN_X)) * (1.0f / (MESH_X_DIST)),
cell_yi = (raw[Y_AXIS] - (MESH_MIN_Y)) * (1.0f / (MESH_Y_DIST));
cell_xi = constrain(cell_xi, 0, (GRID_MAX_POINTS_X) - 1);
cell_yi = constrain(cell_yi, 0, (GRID_MAX_POINTS_Y) - 1);
const float x0 = mesh_index_to_xpos(cell_xi), // 64 byte table lookup avoids mul+add
y0 = mesh_index_to_ypos(cell_yi);
float z_x0y0 = z_values[cell_xi ][cell_yi ], // z at lower left corner
z_x1y0 = z_values[cell_xi+1][cell_yi ], // z at upper left corner
z_x0y1 = z_values[cell_xi ][cell_yi+1], // z at lower right corner
z_x1y1 = z_values[cell_xi+1][cell_yi+1]; // z at upper right corner
if (isnan(z_x0y0)) z_x0y0 = 0; // ideally activating planner.leveling_active (G29 A)
if (isnan(z_x1y0)) z_x1y0 = 0; // should refuse if any invalid mesh points
if (isnan(z_x0y1)) z_x0y1 = 0; // in order to avoid isnan tests per cell,
if (isnan(z_x1y1)) z_x1y1 = 0; // thus guessing zero for undefined points
float cx = raw[X_AXIS] - x0, // cell-relative x and y
cy = raw[Y_AXIS] - y0;
const float z_xmy0 = (z_x1y0 - z_x0y0) * (1.0f / (MESH_X_DIST)), // z slope per x along y0 (lower left to lower right)
z_xmy1 = (z_x1y1 - z_x0y1) * (1.0f / (MESH_X_DIST)); // z slope per x along y1 (upper left to upper right)
float z_cxy0 = z_x0y0 + z_xmy0 * cx; // z height along y0 at cx (changes for each cx in cell)
const float z_cxy1 = z_x0y1 + z_xmy1 * cx, // z height along y1 at cx
z_cxyd = z_cxy1 - z_cxy0; // z height difference along cx from y0 to y1
float z_cxym = z_cxyd * (1.0f / (MESH_Y_DIST)); // z slope per y along cx from y0 to y1 (changes for each cx in cell)
// float z_cxcy = z_cxy0 + z_cxym * cy; // interpolated mesh z height along cx at cy (do inside the segment loop)
// As subsequent segments step through this cell, the z_cxy0 intercept will change
// and the z_cxym slope will change, both as a function of cx within the cell, and
// each change by a constant for fixed segment lengths.
const float z_sxy0 = z_xmy0 * diff[X_AXIS], // per-segment adjustment to z_cxy0
z_sxym = (z_xmy1 - z_xmy0) * (1.0f / (MESH_Y_DIST)) * diff[X_AXIS]; // per-segment adjustment to z_cxym
for (;;) { // for all segments within this mesh cell
if (--segments == 0) // if this is last segment, use rtarget for exact
COPY(raw, rtarget);
const float z_cxcy = (z_cxy0 + z_cxym * cy) // interpolated mesh z height along cx at cy
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
* fade_scaling_factor // apply fade factor to interpolated mesh height
#endif
;
const float z = raw[Z_AXIS];
raw[Z_AXIS] += z_cxcy;
ubl_buffer_segment_raw(raw, feedrate);
raw[Z_AXIS] = z;
if (segments == 0) // done with last segment
return false; // did not set_current_from_destination()
LOOP_XYZE(i) raw[i] += diff[i];
cx += diff[X_AXIS];
cy += diff[Y_AXIS];
if (!WITHIN(cx, 0, MESH_X_DIST) || !WITHIN(cy, 0, MESH_Y_DIST)) // done within this cell, break to next
break;
// Next segment still within same mesh cell, adjust the per-segment
// slope and intercept to compute next z height.
z_cxy0 += z_sxy0; // adjust z_cxy0 by per-segment z_sxy0
z_cxym += z_sxym; // adjust z_cxym by per-segment z_sxym
} // segment loop
} // cell loop
return false; // caller will update current_position
}
