void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
#if CONFIG_HAVE_ACPI_RESUME
void *resume_backup_memory;
#endif
amd_initmmio();
hudson_lpc_port80();
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
post_code(0x31);
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
post_code(0x37);
AGESAWRAPPER(amdinitreset);
post_code(0x38);
printk(BIOS_DEBUG, "Got past agesawrapper_amdinitreset\n");
post_code(0x39);
AGESAWRAPPER(amdinitearly);
int s3resume = acpi_is_wakeup_s3();
if (!s3resume) {
post_code(0x40);
AGESAWRAPPER(amdinitpost);
post_code(0x41);
AGESAWRAPPER(amdinitenv);
/* TODO: Disable cache is not ok. */
disable_cache_as_ram();
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
AGESAWRAPPER(amdinitresume);
AGESAWRAPPER(amds3laterestore);
post_code(0x61);
prepare_for_resume();
}
post_code(0x50);
copy_and_run();
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
/* Must come first to enable PCI MMCONF. */
amd_initmmio();
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
sb_Poweron_Init();
post_code(0x31);
nuvoton_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);
post_code(0x37);
agesawrapper_amdinitreset();
post_code(0x39);
agesawrapper_amdinitearly();
int s3resume = acpi_is_wakeup_s3();
if (!s3resume) {
post_code(0x40);
agesawrapper_amdinitpost();
post_code(0x42);
agesawrapper_amdinitenv();
amd_initenv();
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
agesawrapper_amdinitresume();
agesawrapper_amds3laterestore();
post_code(0x61);
prepare_for_resume();
}
post_code(0x50);
copy_and_run();
printk(BIOS_ERR, "Error: copy_and_run() returned!\n");
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
amd_initmmio();
hudson_lpc_port80();
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
post_code(0x31);
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);
post_code(0x37);
agesawrapper_amdinitreset();
post_code(0x39);
agesawrapper_amdinitearly();
int s3resume = acpi_is_wakeup_s3();
if (!s3resume) {
post_code(0x40);
agesawrapper_amdinitpost();
post_code(0x41);
agesawrapper_amdinitenv();
disable_cache_as_ram();
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
agesawrapper_amdinitresume();
amd_initcpuio();
agesawrapper_amds3laterestore();
post_code(0x61);
prepare_for_resume();
}
post_code(0x50);
copy_and_run();
post_code(0x54); /* Should never see this post code. */
}
void romstage_after_car(void)
{
struct romstage_handoff *handoff;
handoff = romstage_handoff_find_or_add();
prepare_for_resume(handoff);
#if CONFIG_VBOOT_VERIFY_FIRMWARE
vboot_verify_firmware(handoff);
#endif
/* Load the ramstage. */
copy_and_run();
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
/*
* All cores: allow caching of flash chip code and data
* (there are no cache-as-ram reliability concerns with family 14h)
*/
__writemsr (0x20c, (0x0100000000ull - CACHE_ROM_SIZE) | 5);
__writemsr (0x20d, (0x1000000000ull - CACHE_ROM_SIZE) | 0x800);
/* All cores: set pstate 0 (1600 MHz) early to save a few ms of boot time */
__writemsr (0xc0010062, 0);
amd_initmmio();
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
sb_Poweron_Init();
post_code(0x31);
fintek_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);
post_code(0x37);
agesawrapper_amdinitreset();
post_code(0x39);
agesawrapper_amdinitearly();
int s3resume = acpi_is_wakeup_s3();
if (!s3resume) {
post_code(0x40);
agesawrapper_amdinitpost();
post_code(0x42);
agesawrapper_amdinitenv();
amd_initenv();
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
agesawrapper_amdinitresume();
agesawrapper_amds3laterestore();
post_code(0x61);
prepare_for_resume();
}
post_code(0x50);
copy_and_run();
printk(BIOS_ERR, "Error: copy_and_run() returned!\n");
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
u8 byte;
pci_devfn_t dev;
amd_initmmio();
/* Set LPC decode enables. */
dev = PCI_DEV(0, 0x14, 3);
pci_write_config32(dev, 0x44, 0xff03ffd5);
hudson_lpc_port80();
byte = pci_read_config8(dev, 0x48);
byte |= 3; /* 2e, 2f */
pci_write_config8(dev, 0x48, byte);
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
post_code(0x31);
lpc47n217_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
outb(0x24, 0xcd6);
outb(0x1, 0xcd7);
outb(0xea, 0xcd6);
outb(0x1, 0xcd7);
*(u8 *)0xfed80101 = 0x98;
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);
post_code(0x37);
agesawrapper_amdinitreset();
post_code(0x39);
agesawrapper_amdinitearly();
int s3resume = acpi_is_wakeup_s3();
if (!s3resume) {
post_code(0x40);
agesawrapper_amdinitpost();
post_code(0x41);
agesawrapper_amdinitenv();
disable_cache_as_ram();
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
agesawrapper_amdinitresume();
amd_initcpuio();
agesawrapper_amds3laterestore();
post_code(0x61);
prepare_for_resume();
}
post_code(0x50);
copy_and_run();
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
u8 byte;
device_t dev;
AGESAWRAPPER(amdinitmmio);
hudson_lpc_port80();
//__asm__ volatile ("1: jmp 1b");
/* TODO: */
dev = PCI_DEV(0, 0x14, 3);//pci_locate_device(PCI_ID(0x1002, 0x439D), 0);
byte = pci_read_config8(dev, 0x48);
byte |= 3; /* 2e, 2f */
pci_write_config8(dev, 0x48, byte);
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
post_code(0x31);
lpc47n217_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
outb(0x24, 0xcd6);
outb(0x1, 0xcd7);
outb(0xea, 0xcd6);
outb(0x1, 0xcd7);
*(u8 *)0xfed80101 = 0x98;
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
post_code(0x37);
AGESAWRAPPER(amdinitreset);
post_code(0x39);
AGESAWRAPPER(amdinitearly);
int s3resume = acpi_is_wakeup_early() && acpi_s3_resume_allowed();
if (!s3resume) {
post_code(0x40);
AGESAWRAPPER(amdinitpost);
post_code(0x41);
AGESAWRAPPER(amdinitenv);
disable_cache_as_ram();
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
AGESAWRAPPER(amdinitresume);
AGESAWRAPPER(amds3laterestore);
post_code(0x61);
prepare_for_resume();
}
post_code(0x50);
copy_and_run();
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
/*
* In Hudson RRG, PMIOxD2[5:4] is "Drive strength control for
* LpcClk[1:0]". This following register setting has been
* replicated in every reference design since Parmer, so it is
* believed to be required even though it is not documented in
* the SoC BKDGs. Without this setting, there is no serial
* output.
*/
outb(0xD2, 0xcd6);
outb(0x00, 0xcd7);
amd_initmmio();
hudson_lpc_port80();
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
post_code(0x31);
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
post_code(0x37);
AGESAWRAPPER(amdinitreset);
post_code(0x38);
printk(BIOS_DEBUG, "Got past avalon_early_setup\n");
post_code(0x39);
AGESAWRAPPER(amdinitearly);
int s3resume = acpi_is_wakeup_s3();
if (!s3resume) {
post_code(0x40);
AGESAWRAPPER(amdinitpost);
//PspMboxBiosCmdDramInfo();
post_code(0x41);
AGESAWRAPPER(amdinitenv);
/*
If code hangs here, please check cahaltasm.S
*/
disable_cache_as_ram();
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
AGESAWRAPPER(amdinitresume);
AGESAWRAPPER(amds3laterestore);
post_code(0x61);
prepare_for_resume();
}
outb(0xEA, 0xCD6);
outb(0x1, 0xcd7);
post_code(0x50);
copy_and_run();
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
amd_initmmio();
/* Set LPC decode enables. */
pci_devfn_t dev = PCI_DEV(0, 0x14, 3);
pci_write_config32(dev, 0x44, 0xff03ffd5);
hudson_lpc_port80();
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
post_code(0x31);
fintek_enable_serial(SERIAL_DEV1, CONFIG_TTYS0_BASE);
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);
/* On Larne, after LpcClkDrvSth is set, it needs some time to be stable, because of the buffer ICS551M */
int i;
for(i = 0; i < 200000; i++)
val = inb(0xcd6);
post_code(0x37);
agesawrapper_amdinitreset();
post_code(0x38);
printk(BIOS_DEBUG, "Got past yangtze_early_setup\n");
post_code(0x39);
agesawrapper_amdinitearly();
int s3resume = acpi_is_wakeup_s3();
if (!s3resume) {
post_code(0x40);
agesawrapper_amdinitpost();
post_code(0x41);
agesawrapper_amdinitenv();
/* TODO: Disable cache is not ok. */
disable_cache_as_ram();
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
agesawrapper_amdinitresume();
amd_initcpuio();
agesawrapper_amds3laterestore();
post_code(0x61);
prepare_for_resume();
}
outb(0xEA, 0xCD6);
outb(0x1, 0xcd7);
post_code(0x50);
copy_and_run();
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
/* Must come first to enable PCI MMCONF. */
amd_initmmio();
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
sb_Poweron_Init();
post_code(0x31);
winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);
post_code(0x37);
agesawrapper_amdinitreset();
post_code(0x39);
agesawrapper_amdinitearly();
int s3resume = acpi_is_wakeup_s3();
if (!s3resume) {
post_code(0x40);
/* Reboots with outb(3,0x92), outb(4,0xcf9) or triple-fault all
* hang, looks like DRAM re-init goes wrong, don't know why. */
val = agesawrapper_amdinitpost();
if (val == 7) /* fatal, amdinitenv below is going to hang */
outb(0x06, 0x0cf9); /* reset system harder instead */
post_code(0x42);
agesawrapper_amdinitenv();
amd_initenv();
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
agesawrapper_amdinitresume();
agesawrapper_amds3laterestore();
post_code(0x61);
prepare_for_resume();
}
post_code(0x50);
copy_and_run();
printk(BIOS_ERR, "Error: copy_and_run() returned!\n");
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
/*
* In Hudson RRG, PMIOxD2[5:4] is "Drive strength control for
* LpcClk[1:0]". This following register setting has been
* replicated in every reference design since Parmer, so it is
* believed to be required even though it is not documented in
* the SoC BKDGs. Without this setting, there is no serial
* output.
*/
outb(0xD2, 0xcd6);
outb(0x00, 0xcd7);
amd_initmmio();
hudson_lpc_decode();
outb(0x24, 0xCD6);
outb(0x01, 0xCD7);
*(volatile u32 *) (0xFED80000 + 0xE00 + 0x28) |= 1 << 18; /* 24Mhz */
*(volatile u32 *) (0xFED80000 + 0xE00 + 0x40) &= ~(1 << 2); /* 24Mhz */
hudson_lpc_port80();
if (!cpu_init_detectedx) {
post_code(0x30);
f81216h_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE, MODE_7777);
post_code(0x31);
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);
post_code(0x37);
AGESAWRAPPER(amdinitreset);
post_code(0x38);
printk(BIOS_DEBUG, "Got past hudson_early_setup\n");
post_code(0x39);
AGESAWRAPPER(amdinitearly);
int s3resume = acpi_is_wakeup_s3();
if (!s3resume) {
post_code(0x40);
AGESAWRAPPER(amdinitpost);
post_code(0x41);
AGESAWRAPPER(amdinitenv);
/*
If code hangs here, please check cahaltasm.S
*/
disable_cache_as_ram();
}
else if (IS_ENABLED(CONFIG_HAVE_ACPI_RESUME)) { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
AGESAWRAPPER(amdinitresume);
AGESAWRAPPER(amds3laterestore);
post_code(0x61);
prepare_for_resume();
}
post_code(0x50);
copy_and_run();
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
u8 byte;
device_t dev;
#if IS_ENABLED(CONFIG_POST_DEVICE_PCI_PCIE)
hudson_pci_port80();
#endif
#if IS_ENABLED(CONFIG_POST_DEVICE_LPC)
hudson_lpc_port80();
#endif
val = agesawrapper_amdinitmmio();
if (!cpu_init_detectedx && boot_cpu()) {
/* enable SIO LPC decode */
dev = PCI_DEV(0, 0x14, 3);
byte = pci_read_config8(dev, 0x48);
byte |= 3; /* 2e, 2f */
pci_write_config8(dev, 0x48, byte);
/* enable serial decode */
byte = pci_read_config8(dev, 0x44);
byte |= (1 << 6); /* 0x3f8 */
pci_write_config8(dev, 0x44, byte);
post_code(0x30);
/* enable SB MMIO space */
outb(0x24, 0xcd6);
outb(0x1, 0xcd7);
/* enable SIO clock */
sbxxx_enable_48mhzout();
ite_kill_watchdog(GPIO_DEV);
ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
ite_enable_3vsbsw(GPIO_DEV);
console_init();
/* turn on secondary smbus at b20 */
outb(0x28, 0xcd6);
byte = inb(0xcd7);
byte |= 1;
outb(byte, 0xcd7);
/* set DDR3 voltage */
byte = CONFIG_BOARD_ASUS_F2A85_M_DDR3_VOLT_VAL;
/* default is byte = 0x0, so no need to set it in this case */
if (byte)
do_smbus_write_byte(0xb20, 0x15, 0x3, byte);
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
post_code(0x37);
printk(BIOS_DEBUG, "agesawrapper_amdinitreset ");
val = agesawrapper_amdinitreset();
if(val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitreset failed: %x \n", val);
}
post_code(0x39);
val = agesawrapper_amdinitearly ();
if(val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitearly failed: %x \n", val);
}
printk(BIOS_DEBUG, "Got past agesawrapper_amdinitearly\n");
int s3resume = acpi_is_wakeup_early() && acpi_s3_resume_allowed();
if (!s3resume) {
post_code(0x40);
val = agesawrapper_amdinitpost ();
if(val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitpost failed: %x \n", val);
}
printk(BIOS_DEBUG, "Got past agesawrapper_amdinitpost\n");
post_code(0x41);
val = agesawrapper_amdinitenv ();
if(val) {
printk(BIOS_DEBUG, "agesawrapper_amdinitenv failed: %x \n", val);
}
printk(BIOS_DEBUG, "Got past agesawrapper_amdinitenv\n");
disable_cache_as_ram();
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
printk(BIOS_DEBUG, "agesawrapper_amdinitresume ");
val = agesawrapper_amdinitresume();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
printk(BIOS_DEBUG, "agesawrapper_amds3laterestore ");
val = agesawrapper_amds3laterestore ();
if (val)
printk(BIOS_DEBUG, "error level: %x \n", val);
else
printk(BIOS_DEBUG, "passed.\n");
post_code(0x61);
prepare_for_resume();
}
post_code(0x50);
copy_and_run();
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
msr_t msr;
/*
* All cores: allow caching of flash chip code and data
* (there are no cache-as-ram reliability concerns with family 14h)
*/
msr.lo = ((0x0100000000ull - CACHE_ROM_SIZE) | 5) & 0xFFFFFFFF;
msr.hi = ((0x0100000000ull - CACHE_ROM_SIZE) | 5) >> 32;
wrmsr (MSR_MTRR_VARIABLE_BASE6, msr);
msr.lo = ((0x1000000000ull - CACHE_ROM_SIZE) | 0x800) & 0xFFFFFFFF;
msr.hi = ((0x1000000000ull - CACHE_ROM_SIZE) | 0x800) >> 32;
wrmsr (MSR_MTRR_VARIABLE_MASK6, msr);
/* All cores: set pstate 0 (1600 MHz) early to save a few ms of boot time */
msr.lo = 0;
msr.hi = 0;
wrmsr (MSR_PSTATE_CONTROL, msr);
amd_initmmio();
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
sb_Poweron_Init();
post_code(0x31);
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);
post_code(0x37);
agesawrapper_amdinitreset();
post_code(0x39);
agesawrapper_amdinitearly();
int s3resume = acpi_is_wakeup_s3();
if (!s3resume) {
post_code(0x40);
agesawrapper_amdinitpost();
post_code(0x42);
agesawrapper_amdinitenv();
amd_initenv();
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
agesawrapper_amdinitresume();
agesawrapper_amds3laterestore();
post_code(0x61);
prepare_for_resume();
}
post_code(0x50);
copy_and_run();
printk(BIOS_ERR, "Error: copy_and_run() returned!\n");
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
/* In Hudson RRG, PMIOxD2[5:4] is "Drive strength control for
* LpcClk[1:0]". To be consistent with Parmer, setting to 4mA
* even though the register is not documented in the Kabini BKDG.
* Otherwise the serial output is bad code.
*/
outb(0xD2, 0xcd6);
outb(0x00, 0xcd7);
AGESAWRAPPER(amdinitmmio);
hudson_lpc_port80();
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
post_code(0x31);
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
/* On Larne, after LpcClkDrvSth is set, it needs some time to be stable, because of the buffer ICS551M */
int i;
for(i = 0; i < 200000; i++)
val = inb(0xcd6);
post_code(0x37);
AGESAWRAPPER(amdinitreset);
post_code(0x38);
printk(BIOS_DEBUG, "Got past yangtze_early_setup\n");
post_code(0x39);
AGESAWRAPPER(amdinitearly);
int s3resume = acpi_is_wakeup_early() && acpi_s3_resume_allowed();
if (!s3resume) {
post_code(0x40);
AGESAWRAPPER(amdinitpost);
post_code(0x41);
AGESAWRAPPER(amdinitenv);
/* TODO: Disable cache is not ok. */
disable_cache_as_ram();
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
AGESAWRAPPER(amdinitresume);
AGESAWRAPPER(amds3laterestore);
post_code(0x61);
prepare_for_resume();
}
outb(0xEA, 0xCD6);
outb(0x1, 0xcd7);
post_code(0x50);
copy_and_run();
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val, t32;
u32 *addr32;
/* In Hudson RRG, PMIOxD2[5:4] is "Drive strength control for
* LpcClk[1:0]". To be consistent with Parmer, setting to 4mA
* even though the register is not documented in the Kabini BKDG.
* Otherwise the serial output is bad code.
*/
//outb(0xD2, 0xcd6);
//outb(0x00, 0xcd7);
amd_initmmio();
/* Set LPC decode enables. */
pci_devfn_t dev = PCI_DEV(0, 0x14, 3);
pci_write_config32(dev, 0x44, 0xff03ffd5);
hudson_lpc_port80();
/* Enable the AcpiMmio space */
outb(0x24, 0xcd6);
outb(0x1, 0xcd7);
/* Set auxiliary output clock frequency on OSCOUT1 pin to be 48MHz */
addr32 = (u32 *)0xfed80e28;
t32 = *addr32;
t32 &= 0xfff8ffff;
*addr32 = t32;
/* Enable Auxiliary Clock1, disable FCH 14 MHz OscClk */
addr32 = (u32 *)0xfed80e40;
t32 = *addr32;
t32 &= 0xffffbffb;
*addr32 = t32;
if (!cpu_init_detectedx && boot_cpu()) {
post_code(0x30);
post_code(0x31);
/* w83627uhg has a default clk of 48MHz, p.9 of data-sheet */
winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);
/* On Larne, after LpcClkDrvSth is set, it needs some time to be stable, because of the buffer ICS551M */
int i;
for(i = 0; i < 200000; i++)
val = inb(0xcd6);
post_code(0x37);
agesawrapper_amdinitreset();
post_code(0x38);
printk(BIOS_DEBUG, "Got past yangtze_early_setup\n");
post_code(0x39);
agesawrapper_amdinitearly();
int s3resume = acpi_is_wakeup_s3();
if (!s3resume) {
post_code(0x40);
agesawrapper_amdinitpost();
post_code(0x41);
agesawrapper_amdinitenv();
/* TODO: Disable cache is not ok. */
disable_cache_as_ram();
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
agesawrapper_amdinitresume();
amd_initcpuio();
agesawrapper_amds3laterestore();
post_code(0x61);
prepare_for_resume();
}
outb(0xEA, 0xCD6);
outb(0x1, 0xcd7);
post_code(0x50);
copy_and_run();
post_code(0x54); /* Should never see this post code. */
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
u32 val;
#if CONFIG_SVI2_SLOW_SPEED
device_t d18f3_dev = PCI_DEV(0, 0x18, 3);
#endif //CONFIG_SVI2_SLOW_SPEED
#if CONFIG_SVI_WAIT_COMP_DIS
device_t d18f5_dev = PCI_DEV(0, 0x18, 5);
#endif //CONFIG_SVI_WAIT_COMP_DIS
/*
* In Hudson RRG, PMIOxD2[5:4] is "Drive strength control for
* LpcClk[1:0]". This following register setting has been
* replicated in every reference design since Parmer, so it is
* believed to be required even though it is not documented in
* the SoC BKDGs. Without this setting, there is no serial
* output.
*/
outb(0xD2, 0xcd6);
outb(0x00, 0xcd7);
AGESAWRAPPER_PRE_CONSOLE(amdinitmmio);
if (!cpu_init_detectedx && boot_cpu()) {
u32 data, *memptr;
hudson_lpc_port80();
//
// Configure the GPIO's
//
HandleFchGpioTbl ( (GPIO_CONTROL *) &gGpioInitTable[0] );
hudson_clk_output_48Mhz();
post_code(0x31);
console_init();
printk(BIOS_INFO, "14-25-48Mhz Clock settings\n");
memptr = (u32 *)(ACPI_MMIO_BASE + MISC_BASE + FCH_MISC_REG28 );
data = *memptr;
printk(BIOS_INFO, "FCH_MISC_REG28 is 0x%08x \n", data);
memptr = (u32 *)(ACPI_MMIO_BASE + MISC_BASE + FCH_MISC_REG40 );
data = *memptr;
printk(BIOS_INFO, "FCH_MISC_REG40 is 0x%08x \n", data);
//
// Configure clock request
//
data = *((u32 *)(ACPI_MMIO_BASE + MISC_BASE+FCH_MISC_REG00));
data &= 0xFFFF0000;
data |= (0 + 1) << (0 * 4); // CLKREQ 0 to CLK0
data |= (1 + 1) << (1 * 4); // CLKREQ 1 to CLK1
data |= (2 + 1) << (2 * 4); // CLKREQ 2 to CLK2
data |= (3 + 1) << (3 * 4); // CLKREQ 3 to CLK3
*((u32 *)(ACPI_MMIO_BASE + MISC_BASE+FCH_MISC_REG00)) = data;
data = *((u32 *)(ACPI_MMIO_BASE + MISC_BASE+FCH_MISC_REG04));
data &= 0xFFFFFF0F;
data |= 0xA << (1 * 4); // CLKREQ GFX to GFXCLK
*((u32 *)(ACPI_MMIO_BASE + MISC_BASE+FCH_MISC_REG04)) = data;
// //
// // Configure clock strength
// //
// data = *((u32 *)(ACPI_MMIO_BASE + MISC_BASE+FCH_MISC_REG24));
//
// data &= ~( (3 << 18) | (3 << 6) | (3 << 4) | (3 << 2) | (3 << 0) );
// data |= 3 << 18; // GFX CLOCK
// data |= 3 << (0 * 2); // CLK0
// data |= 3 << (1 * 2); // CLK1
// data |= 3 << (2 * 2); // CLK2
// data |= 3 << (3 * 2); // CLK3
//
// *((u32 *)(ACPI_MMIO_BASE + MISC_BASE+FCH_MISC_REG24)) = data;
}
/* Halt if there was a built in self test failure */
post_code(0x34);
report_bist_failure(bist);
/* Load MPB */
val = cpuid_eax(1);
printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);
/*
* This refers to LpcClkDrvSth settling time. Without this setting, processor
* initialization is slow or incorrect, so this wait has been replicated from
* earlier development boards.
*/
{ int i; for(i = 0; i < 200000; i++) inb(0xCD6); }
post_code(0x37);
AGESAWRAPPER(amdinitreset);
/* TODO There is no debug output between the return from amdinitreset and amdinitearly */
post_code(0x38);
printk(BIOS_DEBUG, "Got past avalon_early_setup\n");
post_code(0x39);
AGESAWRAPPER(amdinitearly);
/*
// Moved here to prevent double signon message
// amdinitreset AGESA code might issue a reset when the hardware is in a wrong state.
*/
printk(BIOS_ERR, CONFIG_MAINBOARD_PART_NUMBER "\n");
printk(BIOS_ERR, "coreboot build " COREBOOT_YYYYMMDD_DATE "\n");
#if CONFIG_SVI2_SLOW_SPEED
/* Force SVI2 to slow speed for APU2 */
val = pci_read_config32( d18f3_dev, 0xA0);
if ( val & (1 << 14 ) ) {
printk(BIOS_DEBUG, "SVI2 FREQUENCY 20 Mhz changing to 3.4\n");
val &= ~(1 << 14 );
pci_write_config32(d18f3_dev, 0xA0, val );
} else {
printk(BIOS_DEBUG, "SVI2 FREQUENCY 3.4 Mhz\n");
}
#endif //CONFIG_SVI2_SLOW_SPEED
#if CONFIG_SVI_WAIT_COMP_DIS
/* Disable SVI2 controller to wait for command completion */
val = pci_read_config32( d18f5_dev, 0x12C);
if ( val & (1 << 30 ) ) {
printk(BIOS_DEBUG, "SVI2 Wait completion disabled\n");
} else {
printk(BIOS_DEBUG, "Disabling SVI2 Wait completion\n");
val |= (1 << 30 );
pci_write_config32(d18f5_dev, 0x12C, val );
}
#endif //CONFIG_SVI_WAIT_COMP_DIS
int s3resume = acpi_is_wakeup_s3();
if (!s3resume) {
post_code(0x40);
AGESAWRAPPER(amdinitpost);
//PspMboxBiosCmdDramInfo();
post_code(0x41);
AGESAWRAPPER(amdinitenv);
/*
If code hangs here, please check cahaltasm.S
*/
disable_cache_as_ram();
} else { /* S3 detect */
printk(BIOS_INFO, "S3 detected\n");
post_code(0x60);
AGESAWRAPPER(amdinitresume);
AGESAWRAPPER(amds3laterestore);
post_code(0x61);
prepare_for_resume();
}
outb(0xEA, 0xCD6);
outb(0x1, 0xcd7);
post_code(0x50);
copy_and_run();
post_code(0x54); /* Should never see this post code. */
}
