コード例 #1
0
/* Plot outlines of copper, for copper layer
 */
void PlotLayerOutlines( BOARD* aBoard, PLOTTER* aPlotter,
                        LSET aLayerMask, const PCB_PLOT_PARAMS& aPlotOpt )
{

    BRDITEMS_PLOTTER itemplotter( aPlotter, aBoard, aPlotOpt );
    itemplotter.SetLayerSet( aLayerMask );

    SHAPE_POLY_SET outlines;

    for( LSEQ seq = aLayerMask.Seq( plot_seq, DIM( plot_seq ) );  seq;  ++seq )
    {
        LAYER_ID layer = *seq;

        outlines.RemoveAllContours();
        aBoard->ConvertBrdLayerToPolygonalContours( layer, outlines );

        outlines.Simplify();

        // Plot outlines
        std::vector< wxPoint > cornerList;

        // Now we have one or more basic polygons: plot each polygon
        for( int ii = 0; ii < outlines.OutlineCount(); ii++ )
        {
            for(int kk = 0; kk <= outlines.HoleCount (ii); kk++ )
            {
                cornerList.clear();
                const SHAPE_LINE_CHAIN& path = (kk == 0) ? outlines.COutline( ii ) : outlines.CHole( ii, kk - 1 );

                for( int jj = 0; jj < path.PointCount(); jj++ )
                    cornerList.push_back( wxPoint( path.CPoint( jj ).x , path.CPoint( jj ).y ) );


                // Ensure the polygon is closed
                if( cornerList[0] != cornerList[cornerList.size() - 1] )
                    cornerList.push_back( cornerList[0] );

                aPlotter->PlotPoly( cornerList, NO_FILL );
            }
        }

        // Plot pad holes
        if( aPlotOpt.GetDrillMarksType() != PCB_PLOT_PARAMS::NO_DRILL_SHAPE )
        {
            for( MODULE* module = aBoard->m_Modules; module; module = module->Next() )
            {
                for( D_PAD* pad = module->Pads(); pad; pad = pad->Next() )
                {
                    wxSize hole = pad->GetDrillSize();

                    if( hole.x == 0 || hole.y == 0 )
                        continue;

                    if( hole.x == hole.y )
                        aPlotter->Circle( pad->GetPosition(), hole.x, NO_FILL );
                    else
                    {
                        wxPoint drl_start, drl_end;
                        int width;
                        pad->GetOblongDrillGeometry( drl_start, drl_end, width );
                        aPlotter->ThickSegment( pad->GetPosition() + drl_start,
                                                pad->GetPosition() + drl_end, width, SKETCH );
                    }
                }
            }
        }

        // Plot vias holes
        for( TRACK* track = aBoard->m_Track; track; track = track->Next() )
        {
            const VIA* via = dyn_cast<const VIA*>( track );

            if( via && via->IsOnLayer( layer ) )    // via holes can be not through holes
            {
                aPlotter->Circle( via->GetPosition(), via->GetDrillValue(), NO_FILL );
            }
        }
    }
}
コード例 #2
0
void PlotLayerOutlines( BOARD *aBoard, PLOTTER* aPlotter,
                        LAYER_MSK aLayerMask, const PCB_PLOT_PARAMS& aPlotOpt )
{

    BRDITEMS_PLOTTER itemplotter( aPlotter, aBoard, aPlotOpt );
    itemplotter.SetLayerMask( aLayerMask );

    CPOLYGONS_LIST outlines;

    for( LAYER_NUM layer = FIRST_LAYER; layer < NB_PCB_LAYERS; layer++ )
    {
        LAYER_MSK layer_mask = GetLayerMask( layer );

        if( (aLayerMask & layer_mask ) == 0 )
            continue;

        outlines.RemoveAllContours();
        aBoard->ConvertBrdLayerToPolygonalContours( layer, outlines );

        // Merge all overlapping polygons.
        KI_POLYGON_SET kpolygons;
        KI_POLYGON_SET ktmp;
        outlines.ExportTo( ktmp );

        kpolygons += ktmp;

        // Plot outlines
        std::vector< wxPoint > cornerList;

        for( unsigned ii = 0; ii < kpolygons.size(); ii++ )
        {
            KI_POLYGON polygon = kpolygons[ii];

            // polygon contains only one polygon, but it can have holes linked by
            // overlapping segments.
            // To plot clean outlines, we have to break this polygon into more polygons with
            // no overlapping segments, using Clipper, because boost::polygon
            // does not allow that
            ClipperLib::Path raw_polygon;
            ClipperLib::Paths normalized_polygons;

            for( unsigned ic = 0; ic < polygon.size(); ic++ )
            {
                KI_POLY_POINT corner = *(polygon.begin() + ic);
                raw_polygon.push_back( ClipperLib::IntPoint( corner.x(), corner.y() ) );
            }

            ClipperLib::SimplifyPolygon( raw_polygon, normalized_polygons );

            // Now we have one or more basic polygons: plot each polygon
            for( unsigned ii = 0; ii < normalized_polygons.size(); ii++ )
            {
                ClipperLib::Path& polygon = normalized_polygons[ii];
                cornerList.clear();

                for( unsigned jj = 0; jj < polygon.size(); jj++ )
                    cornerList.push_back( wxPoint( polygon[jj].X , polygon[jj].Y ) );

                // Ensure the polygon is closed
                if( cornerList[0] != cornerList[cornerList.size()-1] )
                    cornerList.push_back( cornerList[0] );

                aPlotter->PlotPoly( cornerList, NO_FILL );
            }
        }

        // Plot pad holes
        if( aPlotOpt.GetDrillMarksType() != PCB_PLOT_PARAMS::NO_DRILL_SHAPE )
        {
            for( MODULE* module = aBoard->m_Modules; module; module = module->Next() )
            {
                for( D_PAD* pad = module->Pads(); pad; pad = pad->Next() )
                {
                    wxSize hole = pad->GetDrillSize();

                    if( hole.x == 0 || hole.y == 0 )
                        continue;

                    if( hole.x == hole.y )
                        aPlotter->Circle( pad->GetPosition(), hole.x, NO_FILL );
                    else
                    {
                        wxPoint drl_start, drl_end;
                        int width;
                        pad->GetOblongDrillGeometry( drl_start, drl_end, width );
                        aPlotter->ThickSegment( pad->GetPosition() + drl_start,
                                pad->GetPosition() + drl_end, width, SKETCH );
                    }
                }
            }
        }

        // Plot vias holes
        for( TRACK* track = aBoard->m_Track; track; track = track->Next() )
        {
            const VIA* via = dyn_cast<const VIA*>( track );

            if( via && via->IsOnLayer( layer ) )    // via holes can be not through holes
            {
                aPlotter->Circle( via->GetPosition(), via->GetDrillValue(), NO_FILL );
            }
        }
    }
}