/*
* Routine: get_board_mem_timings
* Description: If we use SPL then there is no x-loader nor config header
* so we have to setup the DDR timings ourself on the first bank. This
* provides the timing values back to the function that configures
* the memory.
*/
void get_board_mem_timings(struct board_sdrc_timings *timings)
{
int pop_mfr, pop_id;
/*
* We need to identify what PoP memory is on the board so that
* we know what timings to use. To map the ID values please see
* nand_ids.c
*/
identify_nand_chip(&pop_mfr, &pop_id);
if (pop_mfr == NAND_MFR_HYNIX && pop_id == 0xbc) {
/* 256MB DDR */
timings->mcfg = HYNIX_V_MCFG_200(256 << 20);
timings->ctrla = HYNIX_V_ACTIMA_200;
timings->ctrlb = HYNIX_V_ACTIMB_200;
} else {
/* 128MB DDR */
timings->mcfg = MICRON_V_MCFG_165(128 << 20);
timings->ctrla = MICRON_V_ACTIMA_165;
timings->ctrlb = MICRON_V_ACTIMB_165;
}
timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
timings->mr = MICRON_V_MR_165;
}
void get_board_mem_timings(struct board_sdrc_timings *timings)
{
timings->mcfg = HYNIX_V_MCFG_200(256 << 20);
timings->ctrla = HYNIX_V_ACTIMA_200;
timings->ctrlb = HYNIX_V_ACTIMB_200;
timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
timings->mr = MICRON_V_MR_165;
}
/*
* Routine: get_board_mem_timings
* Description: If we use SPL then there is no x-loader nor config header
* so we have to setup the DDR timings ourself on both banks.
*/
void get_board_mem_timings(struct board_sdrc_timings *timings)
{
int mfr, id, err = identify_nand_chip(&mfr, &id);
timings->mr = MICRON_V_MR_165;
if (!err) {
switch (mfr) {
case NAND_MFR_HYNIX:
timings->mcfg = HYNIX_V_MCFG_200(256 << 20);
timings->ctrla = HYNIX_V_ACTIMA_200;
timings->ctrlb = HYNIX_V_ACTIMB_200;
break;
case NAND_MFR_MICRON:
timings->mcfg = MICRON_V_MCFG_200(256 << 20);
timings->ctrla = MICRON_V_ACTIMA_200;
timings->ctrlb = MICRON_V_ACTIMB_200;
break;
default:
/* Should not happen... */
break;
}
timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
gpmc_cs0_flash = MTD_DEV_TYPE_NAND;
} else {
if (get_cpu_family() == CPU_OMAP34XX) {
timings->mcfg = NUMONYX_V_MCFG_165(256 << 20);
timings->ctrla = NUMONYX_V_ACTIMA_165;
timings->ctrlb = NUMONYX_V_ACTIMB_165;
timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
} else {
timings->mcfg = NUMONYX_V_MCFG_200(256 << 20);
timings->ctrla = NUMONYX_V_ACTIMA_200;
timings->ctrlb = NUMONYX_V_ACTIMB_200;
timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
}
gpmc_cs0_flash = MTD_DEV_TYPE_ONENAND;
}
}
/*
* Routine: get_board_mem_timings
* Description: If we use SPL then there is no x-loader nor config header
* so we have to setup the DDR timings ourself on both banks.
*/
void get_board_mem_timings(struct board_sdrc_timings *timings)
{
timings->mr = MICRON_V_MR_165;
switch (get_board_revision()) {
case REVISION_0: /* Micron 1286MB/256MB, 1/2 banks of 128MB */
timings->mcfg = MICRON_V_MCFG_165(256 << 20);
timings->ctrla = MICRON_V_ACTIMA_165;
timings->ctrlb = MICRON_V_ACTIMB_165;
timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
break;
case REVISION_1: /* Micron 256MB/512MB, 1/2 banks of 256MB */
case REVISION_4:
timings->mcfg = MICRON_V_MCFG_200(256 << 20);
timings->ctrla = MICRON_V_ACTIMA_200;
timings->ctrlb = MICRON_V_ACTIMB_200;
timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
break;
case REVISION_2: /* Hynix 256MB/512MB, 1/2 banks of 256MB */
timings->mcfg = HYNIX_V_MCFG_200(256 << 20);
timings->ctrla = HYNIX_V_ACTIMA_200;
timings->ctrlb = HYNIX_V_ACTIMB_200;
timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
break;
case REVISION_3: /* Micron 512MB/1024MB, 1/2 banks of 512MB */
timings->mcfg = MCFG(512 << 20, 15);
timings->ctrla = MICRON_V_ACTIMA_200;
timings->ctrlb = MICRON_V_ACTIMB_200;
timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
break;
default:
timings->mcfg = MICRON_V_MCFG_165(128 << 20);
timings->ctrla = MICRON_V_ACTIMA_165;
timings->ctrlb = MICRON_V_ACTIMB_165;
timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
}
}
