static void set_led_f(int pf, int state)
{
switch (state) {
case STATUS_LED_OFF: bfin_write_PORTFIO_CLEAR(pf); break;
case STATUS_LED_BLINKING: bfin_write_PORTFIO_TOGGLE(pf); break;
case STATUS_LED_ON: bfin_write_PORTFIO_SET(pf); break;
}
}
void board_reset(void)
{
/* workaround for weak pull ups on ssel */
if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) {
bfin_write_PORTF_FER(bfin_read_PORTF_FER() & ~PF10);
bfin_write_PORTFIO_SET(PF10);
udelay(1);
}
}
u8 bfspi_read_8_bits(u16 chip_select)
{
u16 flag_enable, flag;
u8 ret;
if (chip_select < 8) {
flag = bfin_read_SPI_FLG();
flag_enable = flag & ~(1 << (chip_select + 8));
//PRINTK("read: flag: 0x%04x flag_enable: 0x%04x \n", flag, flag_enable);
}
else {
#if (defined(CONFIG_BF533) || defined(CONFIG_BF532))
bfin_write_FIO_FLAG_C((1<<chip_select));
#endif
#if (defined(CONFIG_BF536) || defined(CONFIG_BF537))
bfin_write_PORTFIO_CLEAR((1<<chip_select));
#endif
__builtin_bfin_ssync();
}
/* drop SPISEL */
bfin_write_SPI_FLG(flag_enable);
/* read kicks off transfer, detect end by polling RXS, we
read the shadow register to prevent another transfer
being started
While reading we write a dummy tx value, 0xff. For
the MMC card, a 0 bit indicates the start of a command
sequence therefore an all 1's sequence keeps the MMC
card in the current state.
*/
bfin_write_SPI_TDBR(0xff);
bfin_read_SPI_RDBR(); __builtin_bfin_ssync();
do { } while (!(bfin_read_SPI_STAT() & RXS)); //hardcode RXS mask
ret = bfin_read_SPI_SHADOW(); __builtin_bfin_ssync();
//ret = read_RDBR(); __builtin_bfin_ssync();
PRINTK("\nkern>> read: 0x%04X\n", ret);
/* raise SPISEL */
if (chip_select < 8) {
bfin_write_SPI_FLG(flag);
}
else {
#if (defined(CONFIG_BF533) || defined(CONFIG_BF532))
bfin_write_FIO_FLAG_S((1<<chip_select));
#endif
#if (defined(CONFIG_BF536) || defined(CONFIG_BF537))
bfin_write_PORTFIO_SET((1<<chip_select));
#endif
__builtin_bfin_ssync();
}
return ret;
}
void bfspi_write_8_bits(u16 chip_select, u8 bits)
{
u16 flag_enable, flag;
if (chip_select < 8) {
flag = bfin_read_SPI_FLG();
flag_enable = flag & ~(1 << (chip_select + 8));
//PRINTK("kern>> chip_select: %d write: flag: 0x%04x flag_enable: 0x%04x \n", chip_select, flag, flag_enable);
/* drop SPISEL */
bfin_write_SPI_FLG(flag_enable);
}
else {
#if (defined(CONFIG_BF533) || defined(CONFIG_BF532))
bfin_write_FIO_FLAG_C((1<<chip_select));
#endif
#if (defined(CONFIG_BF536) || defined(CONFIG_BF537))
bfin_write_PORTFIO_CLEAR((1<<chip_select));
#endif
__builtin_bfin_ssync();
}
/* read kicks off transfer, detect end by polling RXS */
bfin_write_SPI_TDBR(bits);
bfin_read_SPI_RDBR(); __builtin_bfin_ssync();
do {} while (!(bfin_read_SPI_STAT() & RXS)); //hardcode RXS mask
//(void) bfin_read_SPI_SHADOW(); //discard data && clear rxs
//__builtin_bfin_ssync();
/* raise SPISEL */
if (chip_select < 8) {
bfin_write_SPI_FLG(flag);
}
else {
#if (defined(CONFIG_BF533) || defined(CONFIG_BF532))
bfin_write_FIO_FLAG_S((1<<chip_select));
#endif
#if (defined(CONFIG_BF536) || defined(CONFIG_BF537))
bfin_write_PORTFIO_SET((1<<chip_select));
#endif
__builtin_bfin_ssync();
}
}
void bfspi_reset(int reset_bit) {
PRINTK("toggle reset\n");
#if (defined(CONFIG_BF533) || defined(CONFIG_BF532))
PRINTK("set reset to PF%d\n",reset_bit);
bfin_write_FIO_DIR(bfin_read_FIO_DIR() | (1<<reset_bit));
__builtin_bfin_ssync();
bfin_write_FIO_FLAG_C((1<<reset_bit));
__builtin_bfin_ssync();
udelay(100);
bfin_write_FIO_FLAG_S((1<<reset_bit));
__builtin_bfin_ssync();
#endif
#if (defined(CONFIG_BF536) || defined(CONFIG_BF537))
if (reset_bit == 1) {
PRINTK("set reset to PF10\n");
bfin_write_PORTF_FER(bfin_read_PORTF_FER() & 0xFBFF);
__builtin_bfin_ssync();
bfin_write_PORTFIO_DIR(bfin_read_PORTFIO_DIR() | 0x0400);
__builtin_bfin_ssync();
bfin_write_PORTFIO_CLEAR(1<<10);
__builtin_bfin_ssync();
udelay(100);
bfin_write_PORTFIO_SET(1<<10);
__builtin_bfin_ssync();
} else if (reset_bit == 2) {
PRINTK("Error: cannot set reset to PJ11\n");
} else if (reset_bit == 3) {
PRINTK("Error: cannot set reset to PJ10\n");
} else if (reset_bit == 4) {
PRINTK("set reset to PF6\n");
bfin_write_PORTF_FER(bfin_read_PORTF_FER() & 0xFFBF);
__builtin_bfin_ssync();
bfin_write_PORTFIO_DIR(bfin_read_PORTFIO_DIR() | 0x0040);
__builtin_bfin_ssync();
bfin_write_PORTFIO_CLEAR(1<<6);
__builtin_bfin_ssync();
udelay(100);
bfin_write_PORTFIO_SET(1<<6);
__builtin_bfin_ssync();
} else if (reset_bit == 5) {
PRINTK("set reset to PF5\n");
bfin_write_PORTF_FER(bfin_read_PORTF_FER() & 0xFFDF);
__builtin_bfin_ssync();
bfin_write_PORTFIO_DIR(bfin_read_PORTFIO_DIR() | 0x0020);
__builtin_bfin_ssync();
bfin_write_PORTFIO_CLEAR(1<<5);
__builtin_bfin_ssync();
udelay(100);
bfin_write_PORTFIO_SET(1<<5);
__builtin_bfin_ssync();
} else if (reset_bit == 6) {
PRINTK("set reset to PF4\n");
bfin_write_PORTF_FER(bfin_read_PORTF_FER() & 0xFFEF);
__builtin_bfin_ssync();
bfin_write_PORTFIO_DIR(bfin_read_PORTFIO_DIR() | 0x0010);
__builtin_bfin_ssync();
bfin_write_PORTFIO_CLEAR(1<<4);
__builtin_bfin_ssync();
udelay(100);
bfin_write_PORTFIO_SET(1<<4);
__builtin_bfin_ssync();
} else if (reset_bit == 7) {
PRINTK("Error: cannot set reset to PJ5\n");
} else if (reset_bit == 8) {
PRINTK("Using PF8 for reset...\n");
bfin_write_PORTF_FER(bfin_read_PORTF_FER() & 0xFEFF);
__builtin_bfin_ssync();
bfin_write_PORTFIO_DIR(bfin_read_PORTFIO_DIR() | 0x0100);
__builtin_bfin_ssync();
bfin_write_PORTFIO_CLEAR(1<<8);
__builtin_bfin_ssync();
udelay(100);
bfin_write_PORTFIO_SET(1<<8);
} else if ( reset_bit == 9 ) {
PRINTK("Using PF9 for reset...\n");
bfin_write_PORTF_FER(bfin_read_PORTF_FER() & 0xFDFF);
__builtin_bfin_ssync();
bfin_write_PORTFIO_DIR(bfin_read_PORTFIO_DIR() | 0x0200);
__builtin_bfin_ssync();
bfin_write_PORTFIO_CLEAR(1<<9);
__builtin_bfin_ssync();
udelay(100);
bfin_write_PORTFIO_SET(1<<9);
}
#endif
/*
p24 3050 data sheet, allow 1ms for PLL lock, with
less than 1ms (1000us) I found register 2 would have
a value of 0 rather than 3, indicating a bad reset.
*/
udelay(1000);
}
