/**
* If the PLL settings are in place switch the CPU core frequency to the max. value
*/
static int pcm038_power_init(void)
{
uint32_t spctl0;
int ret;
spctl0 = get_pll_spctl10();
/* PLL registers already set to their final values? */
if (spctl0 == SPCTL0_VAL && MPCTL0 == MPCTL0_VAL) {
console_flush();
ret = pmic_power();
if (ret == 0) {
/* wait for required power level to run the CPU at 400 MHz */
udelay(100000);
CSCR = CSCR_VAL_FINAL;
PCDR0 = 0x130410c3;
PCDR1 = 0x09030911;
/* Clocks have changed. Notify clients */
clock_notifier_call_chain();
} else {
printf("Failed to initialize PMIC. Will continue with low CPU speed\n");
}
}
/* clock gating enable */
GPCR = 0x00050f08;
return 0;
}
/**
* If the PLL settings are in place switch the CPU core frequency to the max. value
*/
static int pcm038_power_init(void)
{
uint32_t spctl0 = get_pll_spctl10();
struct mc13xxx *mc13xxx = mc13xxx_get();
/* PLL registers already set to their final values? */
if (spctl0 == SPCTL0_VAL &&
readl(MX27_CCM_BASE_ADDR + MX27_MPCTL0) == MPCTL0_VAL) {
console_flush();
if (mc13xxx) {
mc13xxx_reg_write(mc13xxx, MC13783_REG_SWITCHERS(0),
MC13783_SWX_VOLTAGE(MC13783_SWX_VOLTAGE_1_450) |
MC13783_SWX_VOLTAGE_DVS(MC13783_SWX_VOLTAGE_1_450) |
MC13783_SWX_VOLTAGE_STANDBY(MC13783_SWX_VOLTAGE_1_450));
mc13xxx_reg_write(mc13xxx, MC13783_REG_SWITCHERS(4),
MC13783_SW1A_MODE(MC13783_SWX_MODE_NO_PULSE_SKIP) |
MC13783_SW1A_MODE_STANDBY(MC13783_SWX_MODE_NO_PULSE_SKIP) |
MC13783_SW1A_SOFTSTART |
MC13783_SW1B_MODE(MC13783_SWX_MODE_NO_PULSE_SKIP) |
MC13783_SW1B_MODE_STANDBY(MC13783_SWX_MODE_NO_PULSE_SKIP) |
MC13783_SW1B_SOFTSTART |
MC13783_SW_PLL_FACTOR(32));
/* Setup VMMC voltage */
if (IS_ENABLED(CONFIG_MCI_IMX)) {
u32 val;
mc13xxx_reg_read(mc13xxx, MC13783_REG_REG_SETTING(1), &val);
/* VMMC1 = 3.00 V */
val &= ~(7 << 6);
val |= 6 << 6;
mc13xxx_reg_write(mc13xxx, MC13783_REG_REG_SETTING(1), val);
mc13xxx_reg_read(mc13xxx, MC13783_REG_REG_MODE(1), &val);
/* Enable VMMC1 */
val |= 1 << 18;
mc13xxx_reg_write(mc13xxx, MC13783_REG_REG_MODE(1), val);
}
/* wait for required power level to run the CPU at 400 MHz */
udelay(100000);
writel(CSCR_VAL_FINAL, MX27_CCM_BASE_ADDR + MX27_CSCR);
writel(0x130410c3, MX27_CCM_BASE_ADDR + MX27_PCDR0);
writel(0x09030911, MX27_CCM_BASE_ADDR + MX27_PCDR1);
/* Clocks have changed. Notify clients */
clock_notifier_call_chain();
} else {
pr_err("Failed to initialize PMIC. Will continue with low CPU speed\n");
}
}
/* clock gating enable */
writel(0x00050f08, MX27_SYSCTRL_BASE_ADDR + MX27_GPCR);
return 0;
}
