void pci_init(void)
{
struct pci_controller *hose = &pci9054_hose;
/*
* Register the hose
*/
hose->first_busno = 0;
hose->last_busno = 0xff;
/* System memory space */
pci_set_region(hose->regions + 0,
0x00000000, 0x00000000, 0x01000000,
PCI_REGION_MEM | PCI_REGION_SYS_MEMORY);
/* PCI Memory space */
pci_set_region(hose->regions + 1,
0x00000000, 0xc0000000, 0x10000000,
PCI_REGION_MEM);
pci_set_ops(hose,
pci_hose_read_config_byte_via_dword,
pci_hose_read_config_word_via_dword,
pci9054_read_config_dword,
pci_hose_write_config_byte_via_dword,
pci_hose_write_config_word_via_dword,
pci9054_write_config_dword);
hose->region_count = 2;
pci_register_hose(hose);
hose->last_busno = pci_hose_scan(hose);
}
void pci_init_board(void)
{
struct pci_controller* hose = (struct pci_controller *)&local_hose;
u16 reg16;
hose->first_busno = 0;
hose->last_busno = 0xff;
pci_set_region(hose->regions + 0,
CONFIG_SYS_PCI_MEMORY_BUS,
CONFIG_SYS_PCI_MEMORY_PHYS,
CONFIG_SYS_PCI_MEMORY_SIZE,
PCI_REGION_MEM | PCI_REGION_SYS_MEMORY);
/* PCI memory space */
pci_set_region(hose->regions + 1,
CONFIG_SYS_PCI_MEM_BUS,
CONFIG_SYS_PCI_MEM_PHYS,
CONFIG_SYS_PCI_MEM_SIZE,
PCI_REGION_MEM);
/* ISA/PCI memory space */
pci_set_region(hose->regions + 2,
CONFIG_SYS_ISA_MEM_BUS,
CONFIG_SYS_ISA_MEM_PHYS,
CONFIG_SYS_ISA_MEM_SIZE,
PCI_REGION_MEM);
/* PCI I/O space */
pci_set_region(hose->regions + 3,
CONFIG_SYS_PCI_IO_BUS,
CONFIG_SYS_PCI_IO_PHYS,
CONFIG_SYS_PCI_IO_SIZE,
PCI_REGION_IO);
/* ISA/PCI I/O space */
pci_set_region(hose->regions + 4,
CONFIG_SYS_ISA_IO_BUS,
CONFIG_SYS_ISA_IO_PHYS,
CONFIG_SYS_ISA_IO_SIZE,
PCI_REGION_IO);
hose->region_count = 5;
pci_setup_indirect(hose,
MPC106_REG_ADDR,
MPC106_REG_DATA);
pci_register_hose(hose);
hose->last_busno = pci_hose_scan(hose);
/* Initialises the MPC10x PCI Configuration regs. */
pci_read_config_word (PCI_BDF(0,0,0), PCI_COMMAND, ®16);
reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
pci_write_config_word(PCI_BDF(0,0,0), PCI_COMMAND, reg16);
/* Clear non-reserved bits in status register */
pci_write_config_word(PCI_BDF(0,0,0), PCI_STATUS, 0xffff);
}
void board_pci_setup_hose(struct pci_controller *hose)
{
hose->first_busno = 0;
hose->last_busno = 0;
/* PCI memory space */
pci_set_region(hose->regions + 0,
CONFIG_PCI_MEM_BUS,
CONFIG_PCI_MEM_PHYS,
CONFIG_PCI_MEM_SIZE,
PCI_REGION_MEM);
/* PCI IO space */
pci_set_region(hose->regions + 1,
CONFIG_PCI_IO_BUS,
CONFIG_PCI_IO_PHYS,
CONFIG_PCI_IO_SIZE,
PCI_REGION_IO);
pci_set_region(hose->regions + 2,
CONFIG_PCI_PREF_BUS,
CONFIG_PCI_PREF_PHYS,
CONFIG_PCI_PREF_SIZE,
PCI_REGION_PREFETCH);
pci_set_region(hose->regions + 3,
0,
0,
gd->ram_size,
PCI_REGION_MEM | PCI_REGION_SYS_MEMORY);
hose->region_count = 4;
}
int pci_set_regions(struct pci_controller *hose)
{
/* System memory space */
pci_set_region(hose->regions + 0,
SC520_PCI_MEMORY_BUS,
SC520_PCI_MEMORY_PHYS,
SC520_PCI_MEMORY_SIZE,
PCI_REGION_MEM | PCI_REGION_SYS_MEMORY);
/* ISA/PCI memory space */
pci_set_region(hose->regions + 1,
SC520_ISA_MEM_BUS,
SC520_ISA_MEM_PHYS,
SC520_ISA_MEM_SIZE,
PCI_REGION_MEM);
/* PCI I/O space */
pci_set_region(hose->regions + 2,
SC520_PCI_IO_BUS,
SC520_PCI_IO_PHYS,
SC520_PCI_IO_SIZE,
PCI_REGION_IO);
/* ISA/PCI I/O space */
pci_set_region(hose->regions + 3,
SC520_ISA_IO_BUS,
SC520_ISA_IO_PHYS,
SC520_ISA_IO_SIZE,
PCI_REGION_IO);
return 4;
}
void pci_init_board(void)
{
EFI_STATUS status;
tnc_hose.first_busno = 0;
tnc_hose.last_busno = 0xff;
pci_set_region(tnc_hose.regions + 0, 0, 0,
gd->ram_size, PCI_REGION_MEM | PCI_REGION_SYS_MEMORY);
pci_set_region(tnc_hose.regions + 1, CONFIG_SYS_PCI_MEM_BUS, CONFIG_SYS_PCI_MEM_PHYS,
CONFIG_SYS_PCI_MEM_SIZE, PCI_REGION_MEM);
pci_set_region(tnc_hose.regions + 2, CONFIG_SYS_PCI_IO_BUS, CONFIG_SYS_PCI_IO_PHYS,
CONFIG_SYS_PCI_IO_SIZE, PCI_REGION_IO);
tnc_hose.region_count = 3;
pci_setup_type1(&tnc_hose);
pci_register_hose(&tnc_hose);
tnc_hose.last_busno = pci_hose_scan(&tnc_hose);
/* call into FspNotify */
printf("Calling into FSP (notify phase EnumInitPhaseAfterPciEnumeration): ");
if ((status = FspNotifyWrapper(NULL, EnumInitPhaseAfterPciEnumeration)) != FSP_SUCCESS)
printf("fail, error code %x\n", status);
else
printf("OK\n");
}
static inline void init_pcie1(void)
{
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
#ifdef CONFIG_PCIE1
uint io_sel = (gur->pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19;
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *)CONFIG_SYS_PCIE1_ADDR;
struct pci_controller *hose = &pcie1_hose;
int pcie_ep;
struct pci_region *r = hose->regions;
int pcie_configured = is_fsl_pci_cfg(LAW_TRGT_IF_PCIE_1, io_sel);
pcie_ep = fsl_setup_hose(hose, CONFIG_SYS_PCIE1_ADDR);
if (pcie_configured && !(gur->devdisr & MPC85xx_DEVDISR_PCIE)){
printf ("PCIe: %s, base address %x",
pcie_ep ? "Endpoint" : "Root complex", (uint)pci);
if (pci->pme_msg_det) {
pci->pme_msg_det = 0xffffffff;
debug (", with errors. Clearing. Now 0x%08x",
pci->pme_msg_det);
}
puts ("\n");
/* outbound memory */
pci_set_region (r++,
CONFIG_SYS_PCIE1_MEM_BASE,
CONFIG_SYS_PCIE1_MEM_PHYS,
CONFIG_SYS_PCIE1_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
pci_set_region (r++,
CONFIG_SYS_PCIE1_IO_BASE,
CONFIG_SYS_PCIE1_IO_PHYS,
CONFIG_SYS_PCIE1_IO_SIZE,
PCI_REGION_IO);
hose->region_count = r - hose->regions;
hose->first_busno = first_free_busno;
fsl_pci_init(hose, (u32)&pci->cfg_addr, (u32)&pci->cfg_data);
printf (" PCIe on bus %02x..%02x\n",
hose->first_busno, hose->last_busno);
first_free_busno = hose->last_busno + 1;
} else {
printf ("PCIe: disabled\n");
}
#else /* !CONFIG_PCIE1 */
gur->devdisr |= MPC85xx_DEVDISR_PCIE; /* disable */
#endif /* CONFIG_PCIE1 */
}
static void ftpci_preinit(struct ftpci100_data *priv)
{
struct ftpci100_ahbc *ftpci100;
struct pci_controller *hose = (struct pci_controller *)&local_hose;
u32 pci_config_addr;
u32 pci_config_data;
priv->reg_base = CONFIG_FTPCI100_BASE;
priv->io_base = CONFIG_FTPCI100_BASE + CONFIG_FTPCI100_IO_SIZE;
priv->mmio_base = CONFIG_FTPCI100_MEM_BASE;
priv->mem_base = CONFIG_FTPCI100_MEM_BASE + CONFIG_FTPCI100_MEM_SIZE;
ftpci100 = (struct ftpci100_ahbc *)priv->reg_base;
pci_config_addr = (u32) &ftpci100->conf;
pci_config_data = (u32) &ftpci100->data;
/* print device name */
printf("FTPCI100\n");
/* dump basic configuration */
debug("%s: Config addr is %08X, data port is %08X\n",
__func__, pci_config_addr, pci_config_data);
/* PCI memory space */
pci_set_region(hose->regions + 0,
CONFIG_PCI_MEM_BUS,
CONFIG_PCI_MEM_PHYS,
CONFIG_PCI_MEM_SIZE,
PCI_REGION_MEM);
hose->region_count++;
/* PCI IO space */
pci_set_region(hose->regions + 1,
CONFIG_PCI_IO_BUS,
CONFIG_PCI_IO_PHYS,
CONFIG_PCI_IO_SIZE,
PCI_REGION_IO);
hose->region_count++;
#if defined(CONFIG_PCI_SYS_BUS)
/* PCI System Memory space */
pci_set_region(hose->regions + 2,
CONFIG_PCI_SYS_BUS,
CONFIG_PCI_SYS_PHYS,
CONFIG_PCI_SYS_SIZE,
PCI_REGION_MEM | PCI_REGION_SYS_MEMORY);
hose->region_count++;
#endif
/* setup indirect read/write function */
pci_setup_indirect(hose, pci_config_addr, pci_config_data);
/* register hose */
pci_register_hose(hose);
}
int pci_sh4_init(struct pci_controller *hose)
{
hose->first_busno = 0;
hose->region_count = 0;
hose->last_busno = 0xff;
/* PCI memory space */
pci_set_region(hose->regions + 0,
CONFIG_PCI_MEM_BUS,
CONFIG_PCI_MEM_PHYS,
CONFIG_PCI_MEM_SIZE,
PCI_REGION_MEM);
hose->region_count++;
/* PCI IO space */
pci_set_region(hose->regions + 1,
CONFIG_PCI_IO_BUS,
CONFIG_PCI_IO_PHYS,
CONFIG_PCI_IO_SIZE,
PCI_REGION_IO);
hose->region_count++;
#if defined(CONFIG_PCI_SYS_BUS)
/* PCI System Memory space */
pci_set_region(hose->regions + 2,
CONFIG_PCI_SYS_BUS,
CONFIG_PCI_SYS_PHYS,
CONFIG_PCI_SYS_SIZE,
PCI_REGION_MEM | PCI_REGION_SYS_MEMORY);
hose->region_count++;
#endif
udelay(1000);
pci_set_ops(hose,
pci_hose_read_config_byte_via_dword,
pci_hose_read_config_word_via_dword,
pci_sh4_read_config_dword,
pci_hose_write_config_byte_via_dword,
pci_hose_write_config_word_via_dword,
pci_sh4_write_config_dword);
pci_register_hose(hose);
udelay(1000);
#ifdef CONFIG_PCI_SCAN_SHOW
printf("PCI: Bus Dev VenId DevId Class Int\n");
#endif
hose->last_busno = pci_hose_scan(hose);
return 0;
}
void pci_mpc824x_init (struct pci_controller *hose)
{
hose->first_busno = 0;
hose->last_busno = 0xff;
/* System memory space */
pci_set_region(hose->regions + 0,
CHRP_PCI_MEMORY_BUS,
CHRP_PCI_MEMORY_PHYS,
CHRP_PCI_MEMORY_SIZE,
PCI_REGION_MEM | PCI_REGION_SYS_MEMORY);
/* PCI memory space */
pci_set_region(hose->regions + 1,
CHRP_PCI_MEM_BUS,
CHRP_PCI_MEM_PHYS,
CHRP_PCI_MEM_SIZE,
PCI_REGION_MEM);
/* ISA/PCI memory space */
pci_set_region(hose->regions + 2,
CHRP_ISA_MEM_BUS,
CHRP_ISA_MEM_PHYS,
CHRP_ISA_MEM_SIZE,
PCI_REGION_MEM);
/* PCI I/O space */
pci_set_region(hose->regions + 3,
CHRP_PCI_IO_BUS,
CHRP_PCI_IO_PHYS,
CHRP_PCI_IO_SIZE,
PCI_REGION_IO);
/* ISA/PCI I/O space */
pci_set_region(hose->regions + 4,
CHRP_ISA_IO_BUS,
CHRP_ISA_IO_PHYS,
CHRP_ISA_IO_SIZE,
PCI_REGION_IO);
hose->region_count = 5;
pci_setup_indirect(hose,
CHRP_REG_ADDR,
CHRP_REG_DATA);
pci_register_hose(hose);
hose->last_busno = pci_hose_scan(hose);
}
void pci_init_board(void)
{
coreboot_hose.config_table = pci_coreboot_config_table;
coreboot_hose.first_busno = 0;
coreboot_hose.last_busno = 0;
pci_set_region(coreboot_hose.regions + 0, 0x0, 0x0, 0xffffffff,
PCI_REGION_MEM);
coreboot_hose.region_count = 1;
pci_setup_type1(&coreboot_hose);
pci_register_hose(&coreboot_hose);
pci_hose_scan(&coreboot_hose);
}
void pci_mcf547x_8x_init(struct pci_controller *hose)
{
volatile pci_t *pci = (volatile pci_t *) MMAP_PCI;
volatile gpio_t *gpio = (gpio_t *) MMAP_GPIO;
/* Port configuration */
gpio->par_pcibg =
GPIO_PAR_PCIBG_PCIBG0(3) | GPIO_PAR_PCIBG_PCIBG1(3) |
GPIO_PAR_PCIBG_PCIBG2(3) | GPIO_PAR_PCIBG_PCIBG3(3) |
GPIO_PAR_PCIBG_PCIBG4(3);
gpio->par_pcibr =
GPIO_PAR_PCIBR_PCIBR0(3) | GPIO_PAR_PCIBR_PCIBR1(3) |
GPIO_PAR_PCIBR_PCIBR2(3) | GPIO_PAR_PCIBR_PCIBR3(3) |
GPIO_PAR_PCIBR_PCIBR4(3);
/* Assert reset bit */
pci->gscr |= PCI_GSCR_PR;
pci->tcr1 = PCI_TCR1_P;
/* Initiator windows */
pci->iw0btar = CFG_PCI_MEM_PHYS | (CFG_PCI_MEM_PHYS >> 16);
pci->iw1btar = CFG_PCI_IO_PHYS | (CFG_PCI_IO_PHYS >> 16);
pci->iw2btar = CFG_PCI_CFG_PHYS | (CFG_PCI_CFG_PHYS >> 16);
pci->iwcr =
PCI_IWCR_W0C_EN | PCI_IWCR_W1C_EN | PCI_IWCR_W1C_IO |
PCI_IWCR_W2C_EN | PCI_IWCR_W2C_IO;
pci->icr = 0;
/* Enable bus master and mem access */
pci->scr = PCI_SCR_B | PCI_SCR_M;
/* Cache line size and master latency */
pci->cr1 = PCI_CR1_CLS(8) | PCI_CR1_LTMR(0xF8);
pci->cr2 = 0;
#ifdef CFG_PCI_BAR0
pci->bar0 = PCI_BAR_BAR0(CFG_PCI_BAR0);
pci->tbatr0a = CFG_PCI_TBATR0 | PCI_TBATR_EN;
#endif
#ifdef CFG_PCI_BAR1
pci->bar1 = PCI_BAR_BAR1(CFG_PCI_BAR1);
pci->tbatr1a = CFG_PCI_TBATR1 | PCI_TBATR_EN;
#endif
/* Deassert reset bit */
pci->gscr &= ~PCI_GSCR_PR;
udelay(1000);
/* Enable PCI bus master support */
hose->first_busno = 0;
hose->last_busno = 0xff;
pci_set_region(hose->regions + 0, CFG_PCI_MEM_BUS, CFG_PCI_MEM_PHYS,
CFG_PCI_MEM_SIZE, PCI_REGION_MEM);
pci_set_region(hose->regions + 1, CFG_PCI_IO_BUS, CFG_PCI_IO_PHYS,
CFG_PCI_IO_SIZE, PCI_REGION_IO);
pci_set_region(hose->regions + 2, CFG_PCI_SYS_MEM_BUS,
CFG_PCI_SYS_MEM_PHYS, CFG_PCI_SYS_MEM_SIZE,
PCI_REGION_MEM | PCI_REGION_MEMORY);
hose->region_count = 3;
hose->cfg_addr = &(pci->car);
hose->cfg_data = (volatile unsigned char *)CFG_PCI_CFG_BUS;
pci_set_ops(hose, pci_read_cfg_byte, pci_read_cfg_word,
pci_read_cfg_dword, pci_write_cfg_byte, pci_write_cfg_word,
pci_write_cfg_dword);
/* Hose scan */
pci_register_hose(hose);
hose->last_busno = pci_hose_scan(hose);
}
PCI_INIT_RET_TYPE
pci_init_board (void)
{
#ifdef CONFIG_ATH_EMULATION
prmsg("--- Skipping %s for emulation\n", __func__);
#else
uint32_t cmd;
if (is_drqfn() && !is_qca953x()) {
/*
* Dont enable PCIe in DRQFN package as it has some issues
* related to PCIe
*/
PCI_INIT_RETURN;
}
#if defined(CONFIG_MACH_QCA953x)
if (ath_reg_rd(RST_BOOTSTRAP_ADDRESS) & RST_BOOTSTRAP_TESTROM_ENABLE_MASK) {
ath_reg_rmw_clear(RST_MISC2_ADDRESS, RST_MISC2_PERSTN_RCPHY_SET(1));
ath_reg_wr(PCIE_PHY_REG_1_ADDRESS, PCIE_PHY_REG_1_RESET_1);
ath_reg_wr(PCIE_PHY_REG_3_ADDRESS, PCIE_PHY_REG_3_RESET_1);
ath_reg_rmw_set(PCIE_PWR_MGMT_ADDRESS, PCIE_PWR_MGMT_ASSERT_CLKREQN_SET(1));
ath_reg_rmw_set(PCIE_PLL_CONFIG_ADDRESS, PCIE_PLL_CONFIG_PLLPWD_SET(1));
ath_reg_rmw_set(RST_RESET_ADDRESS, RST_RESET_PCIE_RESET_SET(1));
ath_reg_rmw_set(RST_RESET_ADDRESS, RST_RESET_PCIE_PHY_RESET_SET(1));
ath_reg_rmw_clear(RST_CLKGAT_EN_ADDRESS, RST_CLKGAT_EN_PCIE_RC_SET(1));
PCI_INIT_RETURN;
} else {
/* Honeybee -The PCIe reference clock frequency is being changed
to vary from 99.968MHz to 99.999MHz using SS modulation */
ath_reg_wr_nf(PCIE_PLL_DITHER_DIV_MAX_ADDRESS,
PCIE_PLL_DITHER_DIV_MAX_EN_DITHER_SET(0x1) |
PCIE_PLL_DITHER_DIV_MAX_USE_MAX_SET(0x1) |
PCIE_PLL_DITHER_DIV_MAX_DIV_MAX_INT_SET(0x17) |
PCIE_PLL_DITHER_DIV_MAX_DIV_MAX_FRAC_SET(0x3fff));
ath_reg_wr_nf(PCIE_PLL_DITHER_DIV_MIN_ADDRESS,
PCIE_PLL_DITHER_DIV_MIN_DIV_MIN_FRAC_SET(0x3f84)|
PCIE_PLL_DITHER_DIV_MIN_DIV_MIN_INT_SET(0x17));
}
#else
#if defined(CONFIG_MACH_QCA956x)
ath_reg_rmw_set(PCIE_PHY_REG_1_ADDRESS, PCIE_PHY_REG_1_S_SET(PCIE_PHY_REG_1_S_RESET));
ath_reg_wr_nf(PCIE_PLL_DITHER_DIV_MAX_ADDRESS,
PCIE_PLL_DITHER_DIV_MAX_USE_MAX_SET(0x1) |
PCIE_PLL_DITHER_DIV_MAX_DIV_MAX_INT_SET(0x17) |
PCIE_PLL_DITHER_DIV_MAX_DIV_MAX_FRAC_SET(0x3fff));
ath_reg_wr_nf(PCIE_PLL_DITHER_DIV_MIN_ADDRESS,
PCIE_PLL_DITHER_DIV_MIN_DIV_MIN_FRAC_SET(0x3f84) |
PCIE_PLL_DITHER_DIV_MIN_DIV_MIN_INT_SET(0x17));
#else
// common for rc1 and rc2
ath_reg_wr_nf(PCIE_PLL_DITHER_DIV_MAX_ADDRESS,
PCIE_PLL_DITHER_DIV_MAX_EN_DITHER_SET(0x1) |
PCIE_PLL_DITHER_DIV_MAX_USE_MAX_SET(0x1) |
PCIE_PLL_DITHER_DIV_MAX_DIV_MAX_INT_SET(0x14) |
PCIE_PLL_DITHER_DIV_MAX_DIV_MAX_FRAC_SET(0x3ff));
ath_reg_wr_nf(PCIE_PLL_DITHER_DIV_MIN_ADDRESS,
PCIE_PLL_DITHER_DIV_MIN_DIV_MIN_INT_SET(0x14));
#endif
#endif
ath_reg_wr_nf(PCIE_PLL_CONFIG_ADDRESS,
PCIE_PLL_CONFIG_REFDIV_SET(1) |
PCIE_PLL_CONFIG_BYPASS_SET(1) |
PCIE_PLL_CONFIG_PLLPWD_SET(1));
udelay(10000);
ath_reg_rmw_clear(PCIE_PLL_CONFIG_ADDRESS, PCIE_PLL_CONFIG_PLLPWD_SET(1));
udelay(1000);
ath_reg_rmw_clear(PCIE_PLL_CONFIG_ADDRESS, PCIE_PLL_CONFIG_BYPASS_SET(1));
udelay(1000);
#if !defined(CONFIG_MACH_QCA956x)
#ifdef PCIE2_APP_ADDRESS
if (!(ath_reg_rd(RST_BOOTSTRAP_ADDRESS) & RST_BOOTSTRAP_PCIE_RC_EP_SELECT_MASK)) {
pci_rc2_init_board();
return;
}
#endif
ath_reg_rmw_set(RST_RESET_ADDRESS, RST_RESET_PCIE_PHY_RESET_SET(1));
udelay(10000);
ath_reg_rmw_set(RST_RESET_ADDRESS, RST_RESET_PCIE_RESET_SET(1));
udelay(10000);
#ifdef PCIE2_APP_ADDRESS
ath_reg_rmw_clear(RST_MISC2_ADDRESS, RST_MISC2_PERSTN_RCPHY_SET(1));
udelay(10000);
#endif
ath_reg_wr_nf(PCIE_RESET_ADDRESS, 0); // Put endpoint in reset
udelay(100000);
#ifdef PCIE2_APP_ADDRESS
ath_reg_rmw_set(RST_MISC2_ADDRESS, RST_MISC2_PERSTN_RCPHY_SET(1));
udelay(10000);
#endif
ath_reg_rmw_clear(RST_RESET_ADDRESS, RST_RESET_PCIE_PHY_RESET_SET(1));
udelay(10000);
ath_reg_rmw_clear(RST_RESET_ADDRESS, RST_RESET_PCIE_RESET_SET(1));
udelay(10000);
ath_reg_wr_nf(PCIE_APP_ADDRESS, PCIE_APP_PCIE_BAR_MSN_SET(1) |
PCIE_APP_CFG_BE_SET(0xf) |
PCIE_APP_SLV_RESP_ERR_MAP_SET(0x3f) |
PCIE_APP_LTSSM_ENABLE_SET(1));
cmd = PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER | PCI_COMMAND_INVALIDATE |
PCI_COMMAND_PARITY | PCI_COMMAND_SERR | PCI_COMMAND_FAST_BACK;
ath_local_write_config(PCI_COMMAND, 4, cmd);
ath_local_write_config(0x20, 4, 0x1ff01000);
ath_local_write_config(0x24, 4, 0x1ff01000);
ath_reg_wr_nf(PCIE_RESET_ADDRESS, 4); // Pull endpoint out of reset
udelay(100000);
/*
* Check if the WLAN PCI-E H/W is present, If the
* WLAN H/W is not present, skip the PCI platform
* initialization code and return
*/
if (((ath_reg_rd(PCIE_RESET_ADDRESS)) & 0x1) == 0x0) {
prmsg("*** Warning *** : PCIe WLAN Module not found !!!\n");
}
#endif
#ifdef PCIE2_APP_ADDRESS
pci_rc2_init_board();
#endif
#ifndef COMPRESSED_UBOOT
/*
* Now, configure for u-boot tools
*/
hose.first_busno = 0;
hose.last_busno = 0xff;
/* System space */
pci_set_region( &hose.regions[0],
0x80000000,
0x00000000,
32 * 1024 * 1024,
PCI_REGION_MEM | PCI_REGION_MEMORY);
/* PCI memory space */
pci_set_region( &hose.regions[1],
0x10000000,
0x10000000,
128 * 1024 * 1024,
PCI_REGION_MEM);
hose.region_count = 2;
pci_register_hose(&hose);
pci_set_ops( &hose,
pci_hose_read_config_byte_via_dword,
pci_hose_read_config_word_via_dword,
ath_pci_read_config,
pci_hose_write_config_byte_via_dword,
pci_hose_write_config_word_via_dword,
ath_pci_write_config);
#endif
plat_dev_init();
#endif /* CONFIG_ATH_EMULATION */
PCI_INIT_RETURN;
}
void
pci_init_board(void)
{
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
uint io_sel = (gur->pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19;
uint host_agent = (gur->porbmsr & MPC85xx_PORBMSR_HA) >> 16;
#ifdef CONFIG_PCI1
{
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCI1_ADDR;
struct pci_controller *hose = &pci1_hose;
struct pci_config_table *table;
struct pci_region *r = hose->regions;
uint pci_32 = gur->pordevsr & MPC85xx_PORDEVSR_PCI1_PCI32; /* PORDEVSR[15] */
uint pci_arb = gur->pordevsr & MPC85xx_PORDEVSR_PCI1_ARB; /* PORDEVSR[14] */
uint pci_clk_sel = gur->porpllsr & MPC85xx_PORDEVSR_PCI1_SPD; /* PORPLLSR[16] */
uint pci_agent = (host_agent == 3) || (host_agent == 4 ) || (host_agent == 6);
uint pci_speed = get_clock_freq (); /* PCI PSPEED in [4:5] */
if (!(gur->devdisr & MPC85xx_DEVDISR_PCI1)) {
printf (" PCI: %d bit, %s MHz, %s, %s, %s\n",
(pci_32) ? 32 : 64,
(pci_speed == 33333000) ? "33" :
(pci_speed == 66666000) ? "66" : "unknown",
pci_clk_sel ? "sync" : "async",
pci_agent ? "agent" : "host",
pci_arb ? "arbiter" : "external-arbiter"
);
/* inbound */
r += fsl_pci_setup_inbound_windows(r);
/* outbound memory */
pci_set_region(r++,
CONFIG_SYS_PCI1_MEM_BASE,
CONFIG_SYS_PCI1_MEM_PHYS,
CONFIG_SYS_PCI1_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
pci_set_region(r++,
CONFIG_SYS_PCI1_IO_BASE,
CONFIG_SYS_PCI1_IO_PHYS,
CONFIG_SYS_PCI1_IO_SIZE,
PCI_REGION_IO);
hose->region_count = r - hose->regions;
/* relocate config table pointers */
hose->config_table = \
(struct pci_config_table *)((uint)hose->config_table + gd->reloc_off);
for (table = hose->config_table; table && table->vendor; table++)
table->config_device += gd->reloc_off;
hose->first_busno=first_free_busno;
pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
fsl_pci_init(hose);
first_free_busno=hose->last_busno+1;
printf ("PCI on bus %02x - %02x\n",hose->first_busno,hose->last_busno);
#ifdef CONFIG_PCIX_CHECK
if (!(gur->pordevsr & PORDEVSR_PCI)) {
/* PCI-X init */
if (CONFIG_SYS_CLK_FREQ < 66000000)
printf("PCI-X will only work at 66 MHz\n");
reg16 = PCI_X_CMD_MAX_SPLIT | PCI_X_CMD_MAX_READ
| PCI_X_CMD_ERO | PCI_X_CMD_DPERR_E;
pci_hose_write_config_word(hose, bus, PCIX_COMMAND, reg16);
}
#endif
} else {
printf (" PCI: disabled\n");
}
}
#else
gur->devdisr |= MPC85xx_DEVDISR_PCI1; /* disable */
#endif
#ifdef CONFIG_PCI2
{
uint pci2_clk_sel = gur->porpllsr & 0x4000; /* PORPLLSR[17] */
uint pci_dual = get_pci_dual (); /* PCI DUAL in CM_PCI[3] */
if (pci_dual) {
printf (" PCI2: 32 bit, 66 MHz, %s\n",
pci2_clk_sel ? "sync" : "async");
} else {
printf (" PCI2: disabled\n");
}
}
#else
gur->devdisr |= MPC85xx_DEVDISR_PCI2; /* disable */
#endif /* CONFIG_PCI2 */
#ifdef CONFIG_PCIE1
{
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE1_ADDR;
struct pci_controller *hose = &pcie1_hose;
int pcie_ep = (host_agent == 0) || (host_agent == 2 ) || (host_agent == 3);
struct pci_region *r = hose->regions;
int pcie_configured = io_sel >= 1;
if (pcie_configured && !(gur->devdisr & MPC85xx_DEVDISR_PCIE)){
printf ("\n PCIE connected to slot as %s (base address %x)",
pcie_ep ? "End Point" : "Root Complex",
(uint)pci);
if (pci->pme_msg_det) {
pci->pme_msg_det = 0xffffffff;
debug (" with errors. Clearing. Now 0x%08x",pci->pme_msg_det);
}
printf ("\n");
/* inbound */
r += fsl_pci_setup_inbound_windows(r);
/* outbound memory */
pci_set_region(r++,
CONFIG_SYS_PCIE1_MEM_BASE,
CONFIG_SYS_PCIE1_MEM_PHYS,
CONFIG_SYS_PCIE1_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
pci_set_region(r++,
CONFIG_SYS_PCIE1_IO_BASE,
CONFIG_SYS_PCIE1_IO_PHYS,
CONFIG_SYS_PCIE1_IO_SIZE,
PCI_REGION_IO);
hose->region_count = r - hose->regions;
hose->first_busno=first_free_busno;
pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
fsl_pci_init(hose);
printf ("PCIE on bus %d - %d\n",hose->first_busno,hose->last_busno);
first_free_busno=hose->last_busno+1;
} else {
printf (" PCIE: disabled\n");
}
}
#else
gur->devdisr |= MPC85xx_DEVDISR_PCIE; /* disable */
#endif
}
void
pci_init_board(void)
{
volatile ccsr_gur_t *gur = (void *)(CFG_MPC85xx_GUTS_ADDR);
uint io_sel = (gur->pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19;
uint host_agent = (gur->porbmsr & MPC85xx_PORBMSR_HA) >> 16;
#ifdef CONFIG_PCI1
{
pib_init();
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CFG_PCI1_ADDR;
extern void fsl_pci_init(struct pci_controller *hose);
struct pci_controller *hose = &pci1_hose;
uint pci_32 = 1; /* PORDEVSR[15] */
uint pci_arb = gur->pordevsr & MPC85xx_PORDEVSR_PCI1_ARB; /* PORDEVSR[14] */
uint pci_clk_sel = gur->porpllsr & MPC85xx_PORDEVSR_PCI1_SPD; /* PORPLLSR[16] */
uint pci_agent = (host_agent == 3) || (host_agent == 4 ) || (host_agent == 6);
uint pci_speed = 66666000;
if (!(gur->devdisr & MPC85xx_DEVDISR_PCI1)) {
printf (" PCI: %d bit, %s MHz, %s, %s, %s\n",
(pci_32) ? 32 : 64,
(pci_speed == 33333000) ? "33" :
(pci_speed == 66666000) ? "66" : "unknown",
pci_clk_sel ? "sync" : "async",
pci_agent ? "agent" : "host",
pci_arb ? "arbiter" : "external-arbiter"
);
/* inbound */
pci_set_region(hose->regions + 0,
CFG_PCI_MEMORY_BUS,
CFG_PCI_MEMORY_PHYS,
CFG_PCI_MEMORY_SIZE,
PCI_REGION_MEM | PCI_REGION_MEMORY);
/* outbound memory */
pci_set_region(hose->regions + 1,
CFG_PCI1_MEM_BASE,
CFG_PCI1_MEM_PHYS,
CFG_PCI1_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
pci_set_region(hose->regions + 2,
CFG_PCI1_IO_BASE,
CFG_PCI1_IO_PHYS,
CFG_PCI1_IO_SIZE,
PCI_REGION_IO);
hose->region_count = 3;
hose->first_busno = first_free_busno;
pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
fsl_pci_init(hose);
first_free_busno = hose->last_busno+1;
printf ("PCI on bus %02x - %02x\n",hose->first_busno,hose->last_busno);
} else {
printf (" PCI: disabled\n");
}
}
#else
gur->devdisr |= MPC85xx_DEVDISR_PCI1; /* disable */
#endif
#ifdef CONFIG_PCIE1
{
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CFG_PCIE1_ADDR;
extern void fsl_pci_init(struct pci_controller *hose);
struct pci_controller *hose = &pcie1_hose;
int pcie_ep = (host_agent == 0) || (host_agent == 2 ) || (host_agent == 3);
int pcie_configured = io_sel >= 1;
if (pcie_configured && !(gur->devdisr & MPC85xx_DEVDISR_PCIE)){
printf ("\n PCIE connected to slot as %s (base address %x)",
pcie_ep ? "End Point" : "Root Complex",
(uint)pci);
if (pci->pme_msg_det) {
pci->pme_msg_det = 0xffffffff;
debug (" with errors. Clearing. Now 0x%08x",pci->pme_msg_det);
}
printf ("\n");
/* inbound */
pci_set_region(hose->regions + 0,
CFG_PCI_MEMORY_BUS,
CFG_PCI_MEMORY_PHYS,
CFG_PCI_MEMORY_SIZE,
PCI_REGION_MEM | PCI_REGION_MEMORY);
/* outbound memory */
pci_set_region(hose->regions + 1,
CFG_PCIE1_MEM_BASE,
CFG_PCIE1_MEM_PHYS,
CFG_PCIE1_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
pci_set_region(hose->regions + 2,
CFG_PCIE1_IO_BASE,
CFG_PCIE1_IO_PHYS,
CFG_PCIE1_IO_SIZE,
PCI_REGION_IO);
hose->region_count = 3;
hose->first_busno=first_free_busno;
pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
fsl_pci_init(hose);
printf ("PCIE on bus %02x - %02x\n",hose->first_busno,hose->last_busno);
first_free_busno=hose->last_busno+1;
} else {
printf (" PCIE: disabled\n");
}
}
#else
gur->devdisr |= MPC85xx_DEVDISR_PCIE; /* disable */
#endif
}
void pci_init_board(void)
{
#ifdef CONFIG_PCI1
{
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCI1_ADDR;
struct pci_controller *hose = &pci1_hose;
struct pci_region *r = hose->regions;
volatile immap_t *immap = (immap_t *) CONFIG_SYS_CCSRBAR;
volatile ccsr_gur_t *gur = &immap->im_gur;
uint devdisr = gur->devdisr;
uint io_sel = (gur->pordevsr & MPC8641_PORDEVSR_IO_SEL)
>> MPC8641_PORDEVSR_IO_SEL_SHIFT;
#ifdef DEBUG
uint host1_agent = (gur->porbmsr & MPC8641_PORBMSR_HA)
>> MPC8641_PORBMSR_HA_SHIFT;
uint pex1_agent = (host1_agent == 0) || (host1_agent == 1);
#endif
if ((io_sel == 2 || io_sel == 3 || io_sel == 5
|| io_sel == 6 || io_sel == 7 || io_sel == 0xF)
&& !(devdisr & MPC86xx_DEVDISR_PCIEX1)) {
debug("PCI-EXPRESS 1: %s \n", pex1_agent ? "Agent" : "Host");
debug("0x%08x=0x%08x ", &pci->pme_msg_det, pci->pme_msg_det);
if (pci->pme_msg_det) {
pci->pme_msg_det = 0xffffffff;
debug(" with errors. Clearing. Now 0x%08x",
pci->pme_msg_det);
}
debug("\n");
/* outbound memory */
pci_set_region(r++,
CONFIG_SYS_PCI1_MEM_BUS,
CONFIG_SYS_PCI1_MEM_PHYS,
CONFIG_SYS_PCI1_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
pci_set_region(r++,
CONFIG_SYS_PCI1_IO_BUS,
CONFIG_SYS_PCI1_IO_PHYS,
CONFIG_SYS_PCI1_IO_SIZE,
PCI_REGION_IO);
/* inbound */
r += fsl_pci_setup_inbound_windows(r);
hose->region_count = r - hose->regions;
hose->first_busno=first_free_busno;
pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
fsl_pci_init(hose);
first_free_busno=hose->last_busno+1;
printf (" PCI-EXPRESS 1 on bus %02x - %02x\n",
hose->first_busno,hose->last_busno);
/*
* Activate ULI1575 legacy chip by performing a fake
* memory access. Needed to make ULI RTC work.
*/
in_be32((unsigned *) ((char *)(CONFIG_SYS_PCI1_MEM_VIRT
+ CONFIG_SYS_PCI1_MEM_SIZE - 0x1000000)));
} else {
puts("PCI-EXPRESS 1: Disabled\n");
}
}
#else
puts("PCI-EXPRESS1: Disabled\n");
#endif /* CONFIG_PCI1 */
#ifdef CONFIG_PCI2
{
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCI2_ADDR;
struct pci_controller *hose = &pci2_hose;
struct pci_region *r = hose->regions;
/* outbound memory */
pci_set_region(r++,
CONFIG_SYS_PCI2_MEM_BUS,
CONFIG_SYS_PCI2_MEM_PHYS,
CONFIG_SYS_PCI2_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
pci_set_region(r++,
CONFIG_SYS_PCI2_IO_BUS,
CONFIG_SYS_PCI2_IO_PHYS,
CONFIG_SYS_PCI2_IO_SIZE,
PCI_REGION_IO);
/* inbound */
r += fsl_pci_setup_inbound_windows(r);
hose->region_count = r - hose->regions;
hose->first_busno=first_free_busno;
pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
fsl_pci_init(hose);
first_free_busno=hose->last_busno+1;
printf (" PCI-EXPRESS 2 on bus %02x - %02x\n",
hose->first_busno,hose->last_busno);
}
#else
puts("PCI-EXPRESS 2: Disabled\n");
#endif /* CONFIG_PCI2 */
}
static inline void init_pci1(void)
{
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
#ifdef CONFIG_PCI1
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *)CONFIG_SYS_PCI1_ADDR;
struct pci_controller *hose = &pci1_hose;
struct pci_region *r = hose->regions;
/* PORDEVSR[15] */
uint pci_32 = gur->pordevsr & MPC85xx_PORDEVSR_PCI1_PCI32;
/* PORDEVSR[14] */
uint pci_arb = gur->pordevsr & MPC85xx_PORDEVSR_PCI1_ARB;
/* PORPLLSR[16] */
uint pci_clk_sel = gur->porpllsr & MPC85xx_PORDEVSR_PCI1_SPD;
int pci_agent = fsl_setup_hose(hose, CONFIG_SYS_PCI1_ADDR);
uint pci_speed = CONFIG_SYS_CLK_FREQ; /* PCI PSPEED in [4:5] */
if (!(gur->devdisr & MPC85xx_DEVDISR_PCI1)) {
printf ("PCI1: %d bit, %s MHz, %s, %s, %s\n",
(pci_32) ? 32 : 64,
(pci_speed == 33333333) ? "33" :
(pci_speed == 66666666) ? "66" : "unknown",
pci_clk_sel ? "sync" : "async",
pci_agent ? "agent" : "host",
pci_arb ? "arbiter" : "external-arbiter");
/* outbound memory */
pci_set_region (r++,
CONFIG_SYS_PCI1_MEM_BASE,
CONFIG_SYS_PCI1_MEM_PHYS,
CONFIG_SYS_PCI1_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
pci_set_region (r++,
CONFIG_SYS_PCI1_IO_BASE,
CONFIG_SYS_PCI1_IO_PHYS,
CONFIG_SYS_PCI1_IO_SIZE,
PCI_REGION_IO);
hose->region_count = r - hose->regions;
hose->first_busno = first_free_busno;
fsl_pci_init(hose, (u32)&pci->cfg_addr, (u32)&pci->cfg_data);
printf (" PCI on bus %02x..%02x\n",
hose->first_busno, hose->last_busno);
first_free_busno = hose->last_busno + 1;
#ifdef CONFIG_PCIX_CHECK
if (!(gur->pordevsr & MPC85xx_PORDEVSR_PCI1)) {
ushort reg16 =
PCI_X_CMD_MAX_SPLIT | PCI_X_CMD_MAX_READ |
PCI_X_CMD_ERO | PCI_X_CMD_DPERR_E;
uint dev = PCI_BDF(hose->first_busno, 0, 0);
/* PCI-X init */
if (CONFIG_SYS_CLK_FREQ < 66000000)
puts ("PCI-X will only work at 66 MHz\n");
pci_hose_write_config_word (hose, dev, PCIX_COMMAND,
reg16);
}
#endif
} else {
puts ("PCI1: disabled\n");
}
#else /* !CONFIG_PCI1 */
gur->devdisr |= MPC85xx_DEVDISR_PCI1; /* disable */
#endif /* CONFIG_PCI1 */
}
int pci_440_init (struct pci_controller *hose)
{
int reg_num = 0;
#ifndef CONFIG_DISABLE_PISE_TEST
/*--------------------------------------------------------------------------+
* The PCI initialization sequence enable bit must be set ... if not abort
* pci setup since updating the bit requires chip reset.
*--------------------------------------------------------------------------*/
#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE)
unsigned long strap;
mfsdr(sdr_sdstp1,strap);
if ((strap & SDR0_SDSTP1_PISE_MASK) == 0) {
printf("PCI: SDR0_STRP1[PISE] not set.\n");
printf("PCI: Configuration aborted.\n");
return -1;
}
#elif defined(CONFIG_440GP)
unsigned long strap;
strap = mfdcr(cpc0_strp1);
if ((strap & CPC0_STRP1_PISE_MASK) == 0) {
printf("PCI: CPC0_STRP1[PISE] not set.\n");
printf("PCI: Configuration aborted.\n");
return -1;
}
#endif
#endif /* CONFIG_DISABLE_PISE_TEST */
/*--------------------------------------------------------------------------+
* PCI controller init
*--------------------------------------------------------------------------*/
hose->first_busno = 0;
hose->last_busno = 0;
/* PCI I/O space */
pci_set_region(hose->regions + reg_num++,
0x00000000,
PCIX0_IOBASE,
0x10000,
PCI_REGION_IO);
/* PCI memory space */
pci_set_region(hose->regions + reg_num++,
CONFIG_SYS_PCI_TARGBASE,
CONFIG_SYS_PCI_MEMBASE,
#ifdef CONFIG_SYS_PCI_MEMSIZE
CONFIG_SYS_PCI_MEMSIZE,
#else
0x10000000,
#endif
PCI_REGION_MEM );
#if defined(CONFIG_PCI_SYS_MEM_BUS) && defined(CONFIG_PCI_SYS_MEM_PHYS) && \
defined(CONFIG_PCI_SYS_MEM_SIZE)
/* System memory space */
pci_set_region(hose->regions + reg_num++,
CONFIG_PCI_SYS_MEM_BUS,
CONFIG_PCI_SYS_MEM_PHYS,
CONFIG_PCI_SYS_MEM_SIZE,
PCI_REGION_MEM | PCI_REGION_SYS_MEMORY );
#endif
hose->region_count = reg_num;
pci_setup_indirect(hose, PCIX0_CFGADR, PCIX0_CFGDATA);
/* Let board change/modify hose & do initial checks */
if (pci_pre_init (hose) == 0) {
printf("PCI: Board-specific initialization failed.\n");
printf("PCI: Configuration aborted.\n");
return -1;
}
pci_register_hose( hose );
/*--------------------------------------------------------------------------+
* PCI target init
*--------------------------------------------------------------------------*/
#if defined(CONFIG_SYS_PCI_TARGET_INIT)
pci_target_init(hose); /* Let board setup pci target */
#else
out16r( PCIX0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
out16r( PCIX0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_ID );
out16r( PCIX0_CLS, 0x00060000 ); /* Bridge, host bridge */
#endif
#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \
defined(CONFIG_460EX) || defined(CONFIG_460GT)
out32r( PCIX0_BRDGOPT1, 0x04000060 ); /* PLB Rq pri highest */
out32r( PCIX0_BRDGOPT2, in32(PCIX0_BRDGOPT2) | 0x83 ); /* Enable host config, clear Timeout, ensure int src1 */
#elif defined(PCIX0_BRDGOPT1)
out32r( PCIX0_BRDGOPT1, 0x10000060 ); /* PLB Rq pri highest */
out32r( PCIX0_BRDGOPT2, in32(PCIX0_BRDGOPT2) | 1 ); /* Enable host config */
#endif
/*--------------------------------------------------------------------------+
* PCI master init: default is one 256MB region for PCI memory:
* 0x3_00000000 - 0x3_0FFFFFFF ==> CONFIG_SYS_PCI_MEMBASE
*--------------------------------------------------------------------------*/
#if defined(CONFIG_SYS_PCI_MASTER_INIT)
pci_master_init(hose); /* Let board setup pci master */
#else
out32r( PCIX0_POM0SA, 0 ); /* disable */
out32r( PCIX0_POM1SA, 0 ); /* disable */
out32r( PCIX0_POM2SA, 0 ); /* disable */
#if defined(CONFIG_440SPE) || \
defined(CONFIG_460EX) || defined(CONFIG_460GT)
out32r( PCIX0_POM0LAL, 0x10000000 );
out32r( PCIX0_POM0LAH, 0x0000000c );
#else
out32r( PCIX0_POM0LAL, 0x00000000 );
out32r( PCIX0_POM0LAH, 0x00000003 );
#endif
out32r( PCIX0_POM0PCIAL, CONFIG_SYS_PCI_MEMBASE );
out32r( PCIX0_POM0PCIAH, 0x00000000 );
out32r( PCIX0_POM0SA, 0xf0000001 ); /* 256MB, enabled */
out32r( PCIX0_STS, in32r( PCIX0_STS ) & ~0x0000fff8 );
#endif
/*--------------------------------------------------------------------------+
* PCI host configuration -- we don't make any assumptions here ... the
* _board_must_indicate_ what to do -- there's just too many runtime
* scenarios in environments like cPCI, PPMC, etc. to make a determination
* based on hard-coded values or state of arbiter enable.
*--------------------------------------------------------------------------*/
if (is_pci_host(hose)) {
#ifdef CONFIG_PCI_SCAN_SHOW
printf("PCI: Bus Dev VenId DevId Class Int\n");
#endif
#if !defined(CONFIG_440EP) && !defined(CONFIG_440GR) && \
!defined(CONFIG_440EPX) && !defined(CONFIG_440GRX)
out16r( PCIX0_CMD, in16r( PCIX0_CMD ) | PCI_COMMAND_MASTER);
#endif
hose->last_busno = pci_hose_scan(hose);
}
return hose->last_busno;
}
/*-----------------------------------------------------------------------------+
* pci_init. Initializes the 405GP PCI Configuration regs.
*-----------------------------------------------------------------------------*/
void pci_405gp_init(struct pci_controller *hose)
{
int i, reg_num = 0;
bd_t *bd = gd->bd;
unsigned short temp_short;
unsigned long ptmpcila[2] = {CONFIG_SYS_PCI_PTM1PCI, CONFIG_SYS_PCI_PTM2PCI};
#if defined(CONFIG_CPCI405) || defined(CONFIG_PMC405)
char *ptmla_str, *ptmms_str;
#endif
unsigned long ptmla[2] = {CONFIG_SYS_PCI_PTM1LA, CONFIG_SYS_PCI_PTM2LA};
unsigned long ptmms[2] = {CONFIG_SYS_PCI_PTM1MS, CONFIG_SYS_PCI_PTM2MS};
#if defined(CONFIG_PIP405) || defined (CONFIG_MIP405)
unsigned long pmmla[3] = {0x80000000, 0xA0000000, 0};
unsigned long pmmma[3] = {0xE0000001, 0xE0000001, 0};
unsigned long pmmpcila[3] = {0x80000000, 0x00000000, 0};
unsigned long pmmpciha[3] = {0x00000000, 0x00000000, 0};
#else
unsigned long pmmla[3] = {0x80000000, 0,0};
unsigned long pmmma[3] = {0xC0000001, 0,0};
unsigned long pmmpcila[3] = {0x80000000, 0,0};
unsigned long pmmpciha[3] = {0x00000000, 0,0};
#endif
#ifdef CONFIG_PCI_PNP
#if (CONFIG_PCI_HOST == PCI_HOST_AUTO)
char *s;
#endif
#endif
#if defined(CONFIG_CPCI405) || defined(CONFIG_PMC405)
ptmla_str = getenv("ptm1la");
ptmms_str = getenv("ptm1ms");
if(NULL != ptmla_str && NULL != ptmms_str ) {
ptmla[0] = simple_strtoul (ptmla_str, NULL, 16);
ptmms[0] = simple_strtoul (ptmms_str, NULL, 16);
}
ptmla_str = getenv("ptm2la");
ptmms_str = getenv("ptm2ms");
if(NULL != ptmla_str && NULL != ptmms_str ) {
ptmla[1] = simple_strtoul (ptmla_str, NULL, 16);
ptmms[1] = simple_strtoul (ptmms_str, NULL, 16);
}
#endif
/*
* Register the hose
*/
hose->first_busno = 0;
hose->last_busno = 0xff;
/* ISA/PCI I/O space */
pci_set_region(hose->regions + reg_num++,
MIN_PCI_PCI_IOADDR,
MIN_PLB_PCI_IOADDR,
0x10000,
PCI_REGION_IO);
/* PCI I/O space */
pci_set_region(hose->regions + reg_num++,
0x00800000,
0xe8800000,
0x03800000,
PCI_REGION_IO);
reg_num = 2;
/* Memory spaces */
for (i=0; i<2; i++)
if (ptmms[i] & 1)
{
if (!i) hose->pci_fb = hose->regions + reg_num;
pci_set_region(hose->regions + reg_num++,
ptmpcila[i], ptmla[i],
~(ptmms[i] & 0xfffff000) + 1,
PCI_REGION_MEM |
PCI_REGION_SYS_MEMORY);
}
/* PCI memory spaces */
for (i=0; i<3; i++)
if (pmmma[i] & 1)
{
pci_set_region(hose->regions + reg_num++,
pmmpcila[i], pmmla[i],
~(pmmma[i] & 0xfffff000) + 1,
PCI_REGION_MEM);
}
hose->region_count = reg_num;
pci_setup_indirect(hose,
PCICFGADR,
PCICFGDATA);
if (hose->pci_fb)
pciauto_region_init(hose->pci_fb);
/* Let board change/modify hose & do initial checks */
if (pci_pre_init (hose) == 0) {
printf("PCI: Board-specific initialization failed.\n");
printf("PCI: Configuration aborted.\n");
return;
}
pci_register_hose(hose);
/*--------------------------------------------------------------------------+
* 405GP PCI Master configuration.
* Map one 512 MB range of PLB/processor addresses to PCI memory space.
* PLB address 0x80000000-0xBFFFFFFF ==> PCI address 0x80000000-0xBFFFFFFF
* Use byte reversed out routines to handle endianess.
*--------------------------------------------------------------------------*/
out32r(PMM0MA, (pmmma[0]&~0x1)); /* disable, configure PMMxLA, PMMxPCILA first */
out32r(PMM0LA, pmmla[0]);
out32r(PMM0PCILA, pmmpcila[0]);
out32r(PMM0PCIHA, pmmpciha[0]);
out32r(PMM0MA, pmmma[0]);
/*--------------------------------------------------------------------------+
* PMM1 is not used. Initialize them to zero.
*--------------------------------------------------------------------------*/
out32r(PMM1MA, (pmmma[1]&~0x1));
out32r(PMM1LA, pmmla[1]);
out32r(PMM1PCILA, pmmpcila[1]);
out32r(PMM1PCIHA, pmmpciha[1]);
out32r(PMM1MA, pmmma[1]);
/*--------------------------------------------------------------------------+
* PMM2 is not used. Initialize them to zero.
*--------------------------------------------------------------------------*/
out32r(PMM2MA, (pmmma[2]&~0x1));
out32r(PMM2LA, pmmla[2]);
out32r(PMM2PCILA, pmmpcila[2]);
out32r(PMM2PCIHA, pmmpciha[2]);
out32r(PMM2MA, pmmma[2]);
/*--------------------------------------------------------------------------+
* 405GP PCI Target configuration. (PTM1)
* Note: PTM1MS is hardwire enabled but we set the enable bit anyway.
*--------------------------------------------------------------------------*/
out32r(PTM1LA, ptmla[0]); /* insert address */
out32r(PTM1MS, ptmms[0]); /* insert size, enable bit is 1 */
pci_write_config_dword(PCIDEVID_405GP, PCI_BASE_ADDRESS_1, ptmpcila[0]);
/*--------------------------------------------------------------------------+
* 405GP PCI Target configuration. (PTM2)
*--------------------------------------------------------------------------*/
out32r(PTM2LA, ptmla[1]); /* insert address */
pci_write_config_dword(PCIDEVID_405GP, PCI_BASE_ADDRESS_2, ptmpcila[1]);
if (ptmms[1] == 0)
{
out32r(PTM2MS, 0x00000001); /* set enable bit */
pci_write_config_dword(PCIDEVID_405GP, PCI_BASE_ADDRESS_2, 0x00000000);
out32r(PTM2MS, 0x00000000); /* disable */
}
else
{
out32r(PTM2MS, ptmms[1]); /* insert size, enable bit is 1 */
}
/*
* Insert Subsystem Vendor and Device ID
*/
pci_write_config_word(PCIDEVID_405GP, PCI_SUBSYSTEM_VENDOR_ID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
#ifdef CONFIG_CPCI405
if (mfdcr(strap) & PSR_PCI_ARBIT_EN)
pci_write_config_word(PCIDEVID_405GP, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
else
pci_write_config_word(PCIDEVID_405GP, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_DEVICEID2);
#else
pci_write_config_word(PCIDEVID_405GP, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
#endif
/*
* Insert Class-code
*/
#ifdef CONFIG_SYS_PCI_CLASSCODE
pci_write_config_word(PCIDEVID_405GP, PCI_CLASS_SUB_CODE, CONFIG_SYS_PCI_CLASSCODE);
#endif /* CONFIG_SYS_PCI_CLASSCODE */
/*--------------------------------------------------------------------------+
* If PCI speed = 66MHz, set 66MHz capable bit.
*--------------------------------------------------------------------------*/
if (bd->bi_pci_busfreq >= 66000000) {
pci_read_config_word(PCIDEVID_405GP, PCI_STATUS, &temp_short);
pci_write_config_word(PCIDEVID_405GP,PCI_STATUS,(temp_short|PCI_STATUS_66MHZ));
}
#if (CONFIG_PCI_HOST != PCI_HOST_ADAPTER)
#if (CONFIG_PCI_HOST == PCI_HOST_AUTO)
if ((mfdcr(strap) & PSR_PCI_ARBIT_EN) ||
(((s = getenv("pciscan")) != NULL) && (strcmp(s, "yes") == 0)))
#endif
{
/*--------------------------------------------------------------------------+
* Write the 405GP PCI Configuration regs.
* Enable 405GP to be a master on the PCI bus (PMM).
* Enable 405GP to act as a PCI memory target (PTM).
*--------------------------------------------------------------------------*/
pci_read_config_word(PCIDEVID_405GP, PCI_COMMAND, &temp_short);
pci_write_config_word(PCIDEVID_405GP, PCI_COMMAND, temp_short |
PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY);
}
#endif
#if defined(CONFIG_405EP) /* on ppc405ep vendor id is not set */
pci_write_config_word(PCIDEVID_405GP, PCI_VENDOR_ID, 0x1014); /* IBM */
#endif
/*
* Set HCE bit (Host Configuration Enabled)
*/
pci_read_config_word(PCIDEVID_405GP, PCIBRDGOPT2, &temp_short);
pci_write_config_word(PCIDEVID_405GP, PCIBRDGOPT2, (temp_short | 0x0001));
#ifdef CONFIG_PCI_PNP
/*--------------------------------------------------------------------------+
* Scan the PCI bus and configure devices found.
*--------------------------------------------------------------------------*/
#if (CONFIG_PCI_HOST == PCI_HOST_AUTO)
if ((mfdcr(strap) & PSR_PCI_ARBIT_EN) ||
(((s = getenv("pciscan")) != NULL) && (strcmp(s, "yes") == 0)))
#endif
{
#ifdef CONFIG_PCI_SCAN_SHOW
printf("PCI: Bus Dev VenId DevId Class Int\n");
#endif
hose->last_busno = pci_hose_scan(hose);
}
#endif /* CONFIG_PCI_PNP */
}
void pci_init_board(void)
{
volatile immap_t *immap = (immap_t *) CFG_CCSRBAR;
volatile ccsr_gur_t *gur = &immap->im_gur;
uint devdisr = gur->devdisr;
uint io_sel = (gur->pordevsr & MPC8641_PORDEVSR_IO_SEL)
>> MPC8641_PORDEVSR_IO_SEL_SHIFT;
#ifdef CONFIG_PCI1
{
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CFG_PCI1_ADDR;
extern void fsl_pci_init(struct pci_controller *hose);
struct pci_controller *hose = &pci1_hose;
#ifdef DEBUG
uint host1_agent = (gur->porbmsr & MPC8641_PORBMSR_HA)
>> MPC8641_PORBMSR_HA_SHIFT;
uint pex1_agent = (host1_agent == 0) || (host1_agent == 1);
#endif
if ((io_sel == 2 || io_sel == 3 || io_sel == 5
|| io_sel == 6 || io_sel == 7 || io_sel == 0xF)
&& !(devdisr & MPC86xx_DEVDISR_PCIEX1)) {
debug("PCI-EXPRESS 1: %s \n", pex1_agent ? "Agent" : "Host");
debug("0x%08x=0x%08x ", &pci->pme_msg_det, pci->pme_msg_det);
if (pci->pme_msg_det) {
pci->pme_msg_det = 0xffffffff;
debug(" with errors. Clearing. Now 0x%08x",
pci->pme_msg_det);
}
debug("\n");
/* inbound */
pci_set_region(hose->regions + 0,
CFG_PCI_MEMORY_BUS,
CFG_PCI_MEMORY_PHYS,
CFG_PCI_MEMORY_SIZE,
PCI_REGION_MEM | PCI_REGION_MEMORY);
/* outbound memory */
pci_set_region(hose->regions + 1,
CFG_PCI1_MEM_BASE,
CFG_PCI1_MEM_PHYS,
CFG_PCI1_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
pci_set_region(hose->regions + 2,
CFG_PCI1_IO_BASE,
CFG_PCI1_IO_PHYS,
CFG_PCI1_IO_SIZE,
PCI_REGION_IO);
hose->region_count = 3;
hose->first_busno=first_free_busno;
pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
fsl_pci_init(hose);
first_free_busno=hose->last_busno+1;
printf (" PCI-EXPRESS 1 on bus %02x - %02x\n",
hose->first_busno,hose->last_busno);
} else {
puts("PCI-EXPRESS 1: Disabled\n");
}
}
#else
puts("PCI-EXPRESS1: Disabled\n");
#endif /* CONFIG_PCI1 */
#ifdef CONFIG_PCI2
{
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CFG_PCI2_ADDR;
extern void fsl_pci_init(struct pci_controller *hose);
struct pci_controller *hose = &pci2_hose;
/* inbound */
pci_set_region(hose->regions + 0,
CFG_PCI_MEMORY_BUS,
CFG_PCI_MEMORY_PHYS,
CFG_PCI_MEMORY_SIZE,
PCI_REGION_MEM | PCI_REGION_MEMORY);
/* outbound memory */
pci_set_region(hose->regions + 1,
CFG_PCI2_MEM_BASE,
CFG_PCI2_MEM_PHYS,
CFG_PCI2_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
pci_set_region(hose->regions + 2,
CFG_PCI2_IO_BASE,
CFG_PCI2_IO_PHYS,
CFG_PCI2_IO_SIZE,
PCI_REGION_IO);
hose->region_count = 3;
hose->first_busno=first_free_busno;
pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
fsl_pci_init(hose);
first_free_busno=hose->last_busno+1;
printf (" PCI-EXPRESS 2 on bus %02x - %02x\n",
hose->first_busno,hose->last_busno);
}
#else
puts("PCI-EXPRESS 2: Disabled\n");
#endif /* CONFIG_PCI2 */
}
void pci_init_board(void)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_CCSRBAR;
volatile ccsr_gur_t *gur = &immap->im_gur;
uint devdisr = gur->devdisr;
uint io_sel = (gur->pordevsr & MPC8610_PORDEVSR_IO_SEL)
>> MPC8610_PORDEVSR_IO_SEL_SHIFT;
uint host_agent = (gur->porbmsr & MPC8610_PORBMSR_HA)
>> MPC8610_PORBMSR_HA_SHIFT;
printf( " pci_init_board: devdisr=%x, io_sel=%x, host_agent=%x\n",
devdisr, io_sel, host_agent);
#ifdef CONFIG_PCIE1
{
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE1_ADDR;
struct pci_controller *hose = &pcie1_hose;
int pcie_configured = (io_sel == 1) || (io_sel == 4);
int pcie_ep = (host_agent == 0) || (host_agent == 2) ||
(host_agent == 5);
struct pci_region *r = hose->regions;
if (pcie_configured && !(devdisr & MPC86xx_DEVDISR_PCIE1)) {
printf(" PCIe 1 connected to Uli as %s (base address %x)\n",
pcie_ep ? "End Point" : "Root Complex",
(uint)pci);
if (pci->pme_msg_det)
pci->pme_msg_det = 0xffffffff;
/* inbound */
r += fsl_pci_setup_inbound_windows(r);
/* outbound memory */
pci_set_region(r++,
CONFIG_SYS_PCIE1_MEM_BUS,
CONFIG_SYS_PCIE1_MEM_PHYS,
CONFIG_SYS_PCIE1_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
pci_set_region(r++,
CONFIG_SYS_PCIE1_IO_BUS,
CONFIG_SYS_PCIE1_IO_PHYS,
CONFIG_SYS_PCIE1_IO_SIZE,
PCI_REGION_IO);
hose->region_count = r - hose->regions;
hose->first_busno = first_free_busno;
pci_setup_indirect(hose, (int)&pci->cfg_addr,
(int)&pci->cfg_data);
fsl_pci_init(hose);
first_free_busno = hose->last_busno + 1;
printf(" PCI-Express 1 on bus %02x - %02x\n",
hose->first_busno, hose->last_busno);
} else
puts(" PCI-Express 1: Disabled\n");
}
#else
puts("PCI-Express 1: Disabled\n");
#endif /* CONFIG_PCIE1 */
#ifdef CONFIG_PCIE2
{
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE2_ADDR;
struct pci_controller *hose = &pcie2_hose;
struct pci_region *r = hose->regions;
int pcie_configured = (io_sel == 0) || (io_sel == 4);
int pcie_ep = (host_agent == 0) || (host_agent == 1) ||
(host_agent == 4);
if (pcie_configured && !(devdisr & MPC86xx_DEVDISR_PCIE2)) {
printf(" PCI-Express 2 connected to slot as %s" \
" (base address %x)\n",
pcie_ep ? "End Point" : "Root Complex",
(uint)pci);
if (pci->pme_msg_det)
pci->pme_msg_det = 0xffffffff;
/* inbound */
r += fsl_pci_setup_inbound_windows(r);
/* outbound memory */
pci_set_region(r++,
CONFIG_SYS_PCIE2_MEM_BUS,
CONFIG_SYS_PCIE2_MEM_PHYS,
CONFIG_SYS_PCIE2_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
pci_set_region(r++,
CONFIG_SYS_PCIE2_IO_BUS,
CONFIG_SYS_PCIE2_IO_PHYS,
CONFIG_SYS_PCIE2_IO_SIZE,
PCI_REGION_IO);
hose->region_count = r - hose->regions;
hose->first_busno = first_free_busno;
pci_setup_indirect(hose, (int)&pci->cfg_addr,
(int)&pci->cfg_data);
fsl_pci_init(hose);
first_free_busno = hose->last_busno + 1;
printf(" PCI-Express 2 on bus %02x - %02x\n",
hose->first_busno, hose->last_busno);
} else
puts(" PCI-Express 2: Disabled\n");
}
#else
puts("PCI-Express 2: Disabled\n");
#endif /* CONFIG_PCIE2 */
#ifdef CONFIG_PCI1
{
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCI1_ADDR;
struct pci_controller *hose = &pci1_hose;
int pci_agent = (host_agent >= 4) && (host_agent <= 6);
struct pci_region *r = hose->regions;
if ( !(devdisr & MPC86xx_DEVDISR_PCI1)) {
printf(" PCI connected to PCI slots as %s" \
" (base address %x)\n",
pci_agent ? "Agent" : "Host",
(uint)pci);
/* inbound */
r += fsl_pci_setup_inbound_windows(r);
/* outbound memory */
pci_set_region(r++,
CONFIG_SYS_PCI1_MEM_BUS,
CONFIG_SYS_PCI1_MEM_PHYS,
CONFIG_SYS_PCI1_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
pci_set_region(r++,
CONFIG_SYS_PCI1_IO_BUS,
CONFIG_SYS_PCI1_IO_PHYS,
CONFIG_SYS_PCI1_IO_SIZE,
PCI_REGION_IO);
hose->region_count = r - hose->regions;
hose->first_busno = first_free_busno;
pci_setup_indirect(hose, (int) &pci->cfg_addr,
(int) &pci->cfg_data);
fsl_pci_init(hose);
first_free_busno = hose->last_busno + 1;
printf(" PCI on bus %02x - %02x\n",
hose->first_busno, hose->last_busno);
} else
puts(" PCI: Disabled\n");
}
#endif /* CONFIG_PCI1 */
}
void
pci_init_board(void)
{
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
uint devdisr = gur->devdisr;
uint io_sel = (gur->pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19;
uint host_agent = (gur->porbmsr & MPC85xx_PORBMSR_HA) >> 16;
debug (" pci_init_board: devdisr=%x, io_sel=%x, host_agent=%x\n",
devdisr, io_sel, host_agent);
if (io_sel & 1) {
if (!(gur->pordevsr & MPC85xx_PORDEVSR_SGMII1_DIS))
printf (" eTSEC1 is in sgmii mode.\n");
if (!(gur->pordevsr & MPC85xx_PORDEVSR_SGMII3_DIS))
printf (" eTSEC3 is in sgmii mode.\n");
}
#ifdef CONFIG_PCIE3
{
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE3_ADDR;
struct pci_controller *hose = &pcie3_hose;
int pcie_ep = (host_agent == 1);
int pcie_configured = io_sel >= 6;
struct pci_region *r = hose->regions;
if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE)){
printf ("\n PCIE3 connected to ULI as %s (base address %x)",
pcie_ep ? "End Point" : "Root Complex",
(uint)pci);
if (pci->pme_msg_det) {
pci->pme_msg_det = 0xffffffff;
debug (" with errors. Clearing. Now 0x%08x",pci->pme_msg_det);
}
printf ("\n");
/* inbound */
r += fsl_pci_setup_inbound_windows(r);
/* outbound memory */
pci_set_region(r++,
CONFIG_SYS_PCIE3_MEM_BUS,
CONFIG_SYS_PCIE3_MEM_PHYS,
CONFIG_SYS_PCIE3_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
pci_set_region(r++,
CONFIG_SYS_PCIE3_IO_BUS,
CONFIG_SYS_PCIE3_IO_PHYS,
CONFIG_SYS_PCIE3_IO_SIZE,
PCI_REGION_IO);
#ifdef CONFIG_SYS_PCIE3_MEM_BUS2
/* outbound memory */
pci_set_region(r++,
CONFIG_SYS_PCIE3_MEM_BUS2,
CONFIG_SYS_PCIE3_MEM_PHYS2,
CONFIG_SYS_PCIE3_MEM_SIZE2,
PCI_REGION_MEM);
#endif
hose->region_count = r - hose->regions;
hose->first_busno=first_free_busno;
pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
fsl_pci_init(hose);
first_free_busno=hose->last_busno+1;
printf (" PCIE3 on bus %02x - %02x\n",
hose->first_busno,hose->last_busno);
/*
* Activate ULI1575 legacy chip by performing a fake
* memory access. Needed to make ULI RTC work.
*/
in_be32((u32 *)CONFIG_SYS_PCIE3_MEM_BUS);
} else {
printf (" PCIE3: disabled\n");
}
}
#else
gur->devdisr |= MPC85xx_DEVDISR_PCIE3; /* disable */
#endif
#ifdef CONFIG_PCIE1
{
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE1_ADDR;
struct pci_controller *hose = &pcie1_hose;
int pcie_ep = (host_agent == 5);
int pcie_configured = io_sel >= 2;
struct pci_region *r = hose->regions;
if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE)){
printf ("\n PCIE1 connected to Slot2 as %s (base address %x)",
pcie_ep ? "End Point" : "Root Complex",
(uint)pci);
if (pci->pme_msg_det) {
pci->pme_msg_det = 0xffffffff;
debug (" with errors. Clearing. Now 0x%08x",pci->pme_msg_det);
}
printf ("\n");
/* inbound */
r += fsl_pci_setup_inbound_windows(r);
/* outbound memory */
pci_set_region(r++,
CONFIG_SYS_PCIE1_MEM_BUS,
CONFIG_SYS_PCIE1_MEM_PHYS,
CONFIG_SYS_PCIE1_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
pci_set_region(r++,
CONFIG_SYS_PCIE1_IO_BUS,
CONFIG_SYS_PCIE1_IO_PHYS,
CONFIG_SYS_PCIE1_IO_SIZE,
PCI_REGION_IO);
#ifdef CONFIG_SYS_PCIE1_MEM_BUS2
/* outbound memory */
pci_set_region(r++,
CONFIG_SYS_PCIE1_MEM_BUS2,
CONFIG_SYS_PCIE1_MEM_PHYS2,
CONFIG_SYS_PCIE1_MEM_SIZE2,
PCI_REGION_MEM);
#endif
hose->region_count = r - hose->regions;
hose->first_busno=first_free_busno;
pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
fsl_pci_init(hose);
first_free_busno=hose->last_busno+1;
printf(" PCIE1 on bus %02x - %02x\n",
hose->first_busno,hose->last_busno);
} else {
printf (" PCIE1: disabled\n");
}
}
#else
gur->devdisr |= MPC85xx_DEVDISR_PCIE; /* disable */
#endif
#ifdef CONFIG_PCIE2
{
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE2_ADDR;
struct pci_controller *hose = &pcie2_hose;
int pcie_ep = (host_agent == 3);
int pcie_configured = io_sel >= 4;
struct pci_region *r = hose->regions;
if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE)){
printf ("\n PCIE2 connected to Slot 1 as %s (base address %x)",
pcie_ep ? "End Point" : "Root Complex",
(uint)pci);
if (pci->pme_msg_det) {
pci->pme_msg_det = 0xffffffff;
debug (" with errors. Clearing. Now 0x%08x",pci->pme_msg_det);
}
printf ("\n");
/* inbound */
r += fsl_pci_setup_inbound_windows(r);
/* outbound memory */
pci_set_region(r++,
CONFIG_SYS_PCIE2_MEM_BUS,
CONFIG_SYS_PCIE2_MEM_PHYS,
CONFIG_SYS_PCIE2_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
pci_set_region(r++,
CONFIG_SYS_PCIE2_IO_BUS,
CONFIG_SYS_PCIE2_IO_PHYS,
CONFIG_SYS_PCIE2_IO_SIZE,
PCI_REGION_IO);
#ifdef CONFIG_SYS_PCIE2_MEM_BUS2
/* outbound memory */
pci_set_region(r++,
CONFIG_SYS_PCIE2_MEM_BUS2,
CONFIG_SYS_PCIE2_MEM_PHYS2,
CONFIG_SYS_PCIE2_MEM_SIZE2,
PCI_REGION_MEM);
#endif
hose->region_count = r - hose->regions;
hose->first_busno=first_free_busno;
pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
fsl_pci_init(hose);
first_free_busno=hose->last_busno+1;
printf (" PCIE2 on bus %02x - %02x\n",
hose->first_busno,hose->last_busno);
} else {
printf (" PCIE2: disabled\n");
}
}
#else
gur->devdisr |= MPC85xx_DEVDISR_PCIE2; /* disable */
#endif
#ifdef CONFIG_PCI1
{
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCI1_ADDR;
struct pci_controller *hose = &pci1_hose;
struct pci_region *r = hose->regions;
uint pci_agent = (host_agent == 6);
uint pci_speed = 66666000; /*get_clock_freq (); PCI PSPEED in [4:5] */
uint pci_32 = 1;
uint pci_arb = gur->pordevsr & MPC85xx_PORDEVSR_PCI1_ARB; /* PORDEVSR[14] */
uint pci_clk_sel = gur->porpllsr & MPC85xx_PORDEVSR_PCI1_SPD; /* PORPLLSR[16] */
if (!(devdisr & MPC85xx_DEVDISR_PCI1)) {
printf ("\n PCI: %d bit, %s MHz, %s, %s, %s (base address %x)\n",
(pci_32) ? 32 : 64,
(pci_speed == 33333000) ? "33" :
(pci_speed == 66666000) ? "66" : "unknown",
pci_clk_sel ? "sync" : "async",
pci_agent ? "agent" : "host",
pci_arb ? "arbiter" : "external-arbiter",
(uint)pci
);
/* inbound */
r += fsl_pci_setup_inbound_windows(r);
/* outbound memory */
pci_set_region(r++,
CONFIG_SYS_PCI1_MEM_BUS,
CONFIG_SYS_PCI1_MEM_PHYS,
CONFIG_SYS_PCI1_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
pci_set_region(r++,
CONFIG_SYS_PCI1_IO_BUS,
CONFIG_SYS_PCI1_IO_PHYS,
CONFIG_SYS_PCI1_IO_SIZE,
PCI_REGION_IO);
#ifdef CONFIG_SYS_PCIE3_MEM_BUS2
/* outbound memory */
pci_set_region(r++,
CONFIG_SYS_PCIE3_MEM_BUS2,
CONFIG_SYS_PCIE3_MEM_PHYS2,
CONFIG_SYS_PCIE3_MEM_SIZE2,
PCI_REGION_MEM);
#endif
hose->region_count = r - hose->regions;
hose->first_busno=first_free_busno;
pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
fsl_pci_init(hose);
first_free_busno=hose->last_busno+1;
printf ("PCI on bus %02x - %02x\n",
hose->first_busno,hose->last_busno);
} else {
printf (" PCI: disabled\n");
}
}
#else
gur->devdisr |= MPC85xx_DEVDISR_PCI1; /* disable */
#endif
}
/**************************************************************************
* pci_init_board()
*
* NOTICE: PCI2 is not supported. There is only one
* physical PCI slot on the board.
*
*/
void
pci_init_board(void)
{
volatile immap_t * immr;
volatile clk83xx_t * clk;
volatile law83xx_t * pci_law;
volatile pot83xx_t * pci_pot;
volatile pcictrl83xx_t * pci_ctrl;
volatile pciconf83xx_t * pci_conf;
u16 reg16;
u32 reg32;
u32 dev;
struct pci_controller * hose;
immr = (immap_t *)CONFIG_SYS_IMMR;
clk = (clk83xx_t *)&immr->clk;
pci_law = immr->sysconf.pcilaw;
pci_pot = immr->ios.pot;
pci_ctrl = immr->pci_ctrl;
pci_conf = immr->pci_conf;
hose = &pci_hose[0];
/*
* Configure PCI controller and PCI_CLK_OUTPUT both in 66M mode
*/
reg32 = clk->occr;
udelay(2000);
clk->occr = 0xff000000;
udelay(2000);
/*
* Release PCI RST Output signal
*/
pci_ctrl[0].gcr = 0;
udelay(2000);
pci_ctrl[0].gcr = 1;
#ifdef CONFIG_MPC83XX_PCI2
pci_ctrl[1].gcr = 0;
udelay(2000);
pci_ctrl[1].gcr = 1;
#endif
/* We need to wait at least a 1sec based on PCI specs */
{
int i;
for (i = 0; i < 1000; ++i)
udelay (1000);
}
/*
* Configure PCI Local Access Windows
*/
pci_law[0].bar = CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR;
pci_law[0].ar = LAWAR_EN | LAWAR_SIZE_1G;
pci_law[1].bar = CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR;
pci_law[1].ar = LAWAR_EN | LAWAR_SIZE_4M;
/*
* Configure PCI Outbound Translation Windows
*/
/* PCI1 mem space - prefetch */
pci_pot[0].potar = (CONFIG_SYS_PCI1_MEM_BASE >> 12) & POTAR_TA_MASK;
pci_pot[0].pobar = (CONFIG_SYS_PCI1_MEM_PHYS >> 12) & POBAR_BA_MASK;
pci_pot[0].pocmr = POCMR_EN | POCMR_PREFETCH_EN | (POCMR_CM_256M & POCMR_CM_MASK);
/* PCI1 IO space */
pci_pot[1].potar = (CONFIG_SYS_PCI1_IO_BASE >> 12) & POTAR_TA_MASK;
pci_pot[1].pobar = (CONFIG_SYS_PCI1_IO_PHYS >> 12) & POBAR_BA_MASK;
pci_pot[1].pocmr = POCMR_EN | POCMR_IO | (POCMR_CM_1M & POCMR_CM_MASK);
/* PCI1 mmio - non-prefetch mem space */
pci_pot[2].potar = (CONFIG_SYS_PCI1_MMIO_BASE >> 12) & POTAR_TA_MASK;
pci_pot[2].pobar = (CONFIG_SYS_PCI1_MMIO_PHYS >> 12) & POBAR_BA_MASK;
pci_pot[2].pocmr = POCMR_EN | (POCMR_CM_256M & POCMR_CM_MASK);
/*
* Configure PCI Inbound Translation Windows
*/
/* we need RAM mapped to PCI space for the devices to
* access main memory */
pci_ctrl[0].pitar1 = 0x0;
pci_ctrl[0].pibar1 = 0x0;
pci_ctrl[0].piebar1 = 0x0;
pci_ctrl[0].piwar1 = PIWAR_EN | PIWAR_PF | PIWAR_RTT_SNOOP | PIWAR_WTT_SNOOP | (__ilog2(gd->ram_size) - 1);
hose->first_busno = 0;
hose->last_busno = 0xff;
/* PCI memory prefetch space */
pci_set_region(hose->regions + 0,
CONFIG_SYS_PCI1_MEM_BASE,
CONFIG_SYS_PCI1_MEM_PHYS,
CONFIG_SYS_PCI1_MEM_SIZE,
PCI_REGION_MEM|PCI_REGION_PREFETCH);
/* PCI memory space */
pci_set_region(hose->regions + 1,
CONFIG_SYS_PCI1_MMIO_BASE,
CONFIG_SYS_PCI1_MMIO_PHYS,
CONFIG_SYS_PCI1_MMIO_SIZE,
PCI_REGION_MEM);
/* PCI IO space */
pci_set_region(hose->regions + 2,
CONFIG_SYS_PCI1_IO_BASE,
CONFIG_SYS_PCI1_IO_PHYS,
CONFIG_SYS_PCI1_IO_SIZE,
PCI_REGION_IO);
/* System memory space */
pci_set_region(hose->regions + 3,
CONFIG_PCI_SYS_MEM_BUS,
CONFIG_PCI_SYS_MEM_PHYS,
gd->ram_size,
PCI_REGION_MEM | PCI_REGION_SYS_MEMORY);
hose->region_count = 4;
pci_setup_indirect(hose,
(CONFIG_SYS_IMMR+0x8300),
(CONFIG_SYS_IMMR+0x8304));
pci_register_hose(hose);
/*
* Write to Command register
*/
reg16 = 0xff;
dev = PCI_BDF(hose->first_busno, 0, 0);
pci_hose_read_config_word (hose, dev, PCI_COMMAND, ®16);
reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
pci_hose_write_config_word(hose, dev, PCI_COMMAND, reg16);
/*
* Clear non-reserved bits in status register.
*/
pci_hose_write_config_word(hose, dev, PCI_STATUS, 0xffff);
pci_hose_write_config_byte(hose, dev, PCI_LATENCY_TIMER, 0x80);
pci_hose_write_config_byte(hose, dev, PCI_CACHE_LINE_SIZE, 0x08);
#ifdef CONFIG_PCI_SCAN_SHOW
printf("PCI: Bus Dev VenId DevId Class Int\n");
#endif
/*
* Hose scan.
*/
hose->last_busno = pci_hose_scan(hose);
#ifdef CONFIG_MPC83XX_PCI2
hose = &pci_hose[1];
/*
* Configure PCI Outbound Translation Windows
*/
/* PCI2 mem space - prefetch */
pci_pot[3].potar = (CONFIG_SYS_PCI2_MEM_BASE >> 12) & POTAR_TA_MASK;
pci_pot[3].pobar = (CONFIG_SYS_PCI2_MEM_PHYS >> 12) & POBAR_BA_MASK;
pci_pot[3].pocmr = POCMR_EN | POCMR_PCI2 | POCMR_PREFETCH_EN | (POCMR_CM_256M & POCMR_CM_MASK);
/* PCI2 IO space */
pci_pot[4].potar = (CONFIG_SYS_PCI2_IO_BASE >> 12) & POTAR_TA_MASK;
pci_pot[4].pobar = (CONFIG_SYS_PCI2_IO_PHYS >> 12) & POBAR_BA_MASK;
pci_pot[4].pocmr = POCMR_EN | POCMR_PCI2 | POCMR_IO | (POCMR_CM_1M & POCMR_CM_MASK);
/* PCI2 mmio - non-prefetch mem space */
pci_pot[5].potar = (CONFIG_SYS_PCI2_MMIO_BASE >> 12) & POTAR_TA_MASK;
pci_pot[5].pobar = (CONFIG_SYS_PCI2_MMIO_PHYS >> 12) & POBAR_BA_MASK;
pci_pot[5].pocmr = POCMR_EN | POCMR_PCI2 | (POCMR_CM_256M & POCMR_CM_MASK);
/*
* Configure PCI Inbound Translation Windows
*/
/* we need RAM mapped to PCI space for the devices to
* access main memory */
pci_ctrl[1].pitar1 = 0x0;
pci_ctrl[1].pibar1 = 0x0;
pci_ctrl[1].piebar1 = 0x0;
pci_ctrl[1].piwar1 = PIWAR_EN | PIWAR_PF | PIWAR_RTT_SNOOP | PIWAR_WTT_SNOOP | (__ilog2(gd->ram_size) - 1);
hose->first_busno = pci_hose[0].last_busno + 1;
hose->last_busno = 0xff;
/* PCI memory prefetch space */
pci_set_region(hose->regions + 0,
CONFIG_SYS_PCI2_MEM_BASE,
CONFIG_SYS_PCI2_MEM_PHYS,
CONFIG_SYS_PCI2_MEM_SIZE,
PCI_REGION_MEM|PCI_REGION_PREFETCH);
/* PCI memory space */
pci_set_region(hose->regions + 1,
CONFIG_SYS_PCI2_MMIO_BASE,
CONFIG_SYS_PCI2_MMIO_PHYS,
CONFIG_SYS_PCI2_MMIO_SIZE,
PCI_REGION_MEM);
/* PCI IO space */
pci_set_region(hose->regions + 2,
CONFIG_SYS_PCI2_IO_BASE,
CONFIG_SYS_PCI2_IO_PHYS,
CONFIG_SYS_PCI2_IO_SIZE,
PCI_REGION_IO);
/* System memory space */
pci_set_region(hose->regions + 3,
CONFIG_PCI_SYS_MEM_BUS,
CONFIG_PCI_SYS_MEM_PHYS,
gd->ram_size,
PCI_REGION_MEM | PCI_REGION_SYS_MEMORY);
hose->region_count = 4;
pci_setup_indirect(hose,
(CONFIG_SYS_IMMR+0x8380),
(CONFIG_SYS_IMMR+0x8384));
pci_register_hose(hose);
/*
* Write to Command register
*/
reg16 = 0xff;
dev = PCI_BDF(hose->first_busno, 0, 0);
pci_hose_read_config_word (hose, dev, PCI_COMMAND, ®16);
reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
pci_hose_write_config_word(hose, dev, PCI_COMMAND, reg16);
/*
* Clear non-reserved bits in status register.
*/
pci_hose_write_config_word(hose, dev, PCI_STATUS, 0xffff);
pci_hose_write_config_byte(hose, dev, PCI_LATENCY_TIMER, 0x80);
pci_hose_write_config_byte(hose, dev, PCI_CACHE_LINE_SIZE, 0x08);
/*
* Hose scan.
*/
hose->last_busno = pci_hose_scan(hose);
#endif
}
void pcie_setup_hoses(int busno)
{
struct pci_controller *hose;
int i, bus;
char *env;
unsigned int delay;
/*
* assume we're called after the PCIX hose is initialized, which takes
* bus ID 0 and therefore start numbering PCIe's from 1.
*/
bus = busno;
for (i = 0; i <= 2; i++) {
/* Check for yucca card presence */
if (!yucca_pcie_card_present(i))
continue;
#ifdef PCIE_ENDPOINT
yucca_setup_pcie_fpga_endpoint(i);
if (ppc440spe_init_pcie_endport(i)) {
#else
yucca_setup_pcie_fpga_rootpoint(i);
if (ppc440spe_init_pcie_rootport(i)) {
#endif
printf("PCIE%d: initialization failed\n", i);
continue;
}
hose = &pcie_hose[i];
hose->first_busno = bus;
hose->last_busno = bus;
hose->current_busno = bus;
/* setup mem resource */
pci_set_region(hose->regions + 0,
CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE,
CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE,
CFG_PCIE_MEMSIZE,
PCI_REGION_MEM
);
hose->region_count = 1;
pci_register_hose(hose);
#ifdef PCIE_ENDPOINT
ppc440spe_setup_pcie_endpoint(hose, i);
/*
* Reson for no scanning is endpoint can not generate
* upstream configuration accesses.
*/
#else
ppc440spe_setup_pcie_rootpoint(hose, i);
env = getenv ("pciscandelay");
if (env != NULL) {
delay = simple_strtoul (env, NULL, 10);
if (delay > 5)
printf ("Warning, expect noticable delay before PCIe"
"scan due to 'pciscandelay' value!\n");
mdelay (delay * 1000);
}
/*
* Config access can only go down stream
*/
hose->last_busno = pci_hose_scan(hose);
bus = hose->last_busno + 1;
#endif
}
}
#endif /* defined(CONFIG_PCI) */
int misc_init_f (void)
{
uint reg;
#if defined(CONFIG_STRESS)
uint i ;
uint disp;
#endif
out16(FPGA_REG10, (in16(FPGA_REG10) &
~(FPGA_REG10_AUTO_NEG_DIS|FPGA_REG10_RESET_ETH)) |
FPGA_REG10_10MHZ_ENABLE |
FPGA_REG10_100MHZ_ENABLE |
FPGA_REG10_GIGABIT_ENABLE |
FPGA_REG10_FULL_DUPLEX );
udelay(10000); /* wait 10ms */
out16(FPGA_REG10, (in16(FPGA_REG10) | FPGA_REG10_RESET_ETH));
/* minimal init for PCIe */
/* pci express 0 Endpoint Mode */
mfsdr(SDR0_PE0DLPSET, reg);
reg &= (~0x00400000);
mtsdr(SDR0_PE0DLPSET, reg);
/* pci express 1 Rootpoint Mode */
mfsdr(SDR0_PE1DLPSET, reg);
reg |= 0x00400000;
mtsdr(SDR0_PE1DLPSET, reg);
/* pci express 2 Rootpoint Mode */
mfsdr(SDR0_PE2DLPSET, reg);
reg |= 0x00400000;
mtsdr(SDR0_PE2DLPSET, reg);
out16(FPGA_REG1C,(in16 (FPGA_REG1C) &
~FPGA_REG1C_PE0_ROOTPOINT &
~FPGA_REG1C_PE1_ENDPOINT &
~FPGA_REG1C_PE2_ENDPOINT));
#if defined(CONFIG_STRESS)
/*
* all this setting done by linux only needed by stress an charac. test
* procedure
* PCIe 1 Rootpoint PCIe2 Endpoint
* PCIe 0 FIR Pre-emphasis Filter Coefficients & Transmit Driver
* Power Level
*/
for (i = 0, disp = 0; i < 8; i++, disp += 3) {
mfsdr(SDR0_PE0HSSSET1L0 + disp, reg);
reg |= 0x33000000;
mtsdr(SDR0_PE0HSSSET1L0 + disp, reg);
}
/*
* PCIe 1 FIR Pre-emphasis Filter Coefficients & Transmit Driver
* Power Level
*/
for (i = 0, disp = 0; i < 4; i++, disp += 3) {
mfsdr(SDR0_PE1HSSSET1L0 + disp, reg);
reg |= 0x33000000;
mtsdr(SDR0_PE1HSSSET1L0 + disp, reg);
}
/*
* PCIE 2 FIR Pre-emphasis Filter Coefficients & Transmit Driver
* Power Level
*/
for (i = 0, disp = 0; i < 4; i++, disp += 3) {
mfsdr(SDR0_PE2HSSSET1L0 + disp, reg);
reg |= 0x33000000;
mtsdr(SDR0_PE2HSSSET1L0 + disp, reg);
}
reg = 0x21242222;
mtsdr(SDR0_PE2UTLSET1, reg);
reg = 0x11000000;
mtsdr(SDR0_PE2UTLSET2, reg);
/* pci express 1 Endpoint Mode */
reg = 0x00004000;
mtsdr(SDR0_PE2DLPSET, reg);
mtsdr(SDR0_UART1, 0x2080005a); /* patch for TG */
#endif
return 0;
}
void pci_init_board(void)
{
int mem_target, mem_attr, i;
int bus = 0;
u32 reg;
u32 soc_ctrl = readl(MVEBU_SYSTEM_REG_BASE + 0x4);
/* Check SoC Control Power State */
debug("%s: SoC Control %08x, 0en %01lx, 1en %01lx, 2en %01lx\n",
__func__, soc_ctrl, SELECT(soc_ctrl, 0), SELECT(soc_ctrl, 1),
SELECT(soc_ctrl, 2));
for (i = 0; i < MAX_PEX; i++) {
struct mvebu_pcie *pcie = &pcie_bus[i];
struct pci_controller *hose = &pcie->hose;
/* Get port number, lane number and memory target / attr */
mvebu_get_port_lane(pcie, i, &mem_target, &mem_attr);
/* Don't read at all from pci registers if port power is down */
if (pcie->lane == 0 && SELECT(soc_ctrl, pcie->port) == 0) {
i += 3;
debug("%s: skipping port %d\n", __func__, pcie->port);
continue;
}
pcie->base = (void __iomem *)PCIE_BASE(i);
/* Check link and skip ports that have no link */
if (!mvebu_pcie_link_up(pcie)) {
debug("%s: PCIe %d.%d - down\n", __func__,
pcie->port, pcie->lane);
continue;
}
debug("%s: PCIe %d.%d - up, base %08x\n", __func__,
pcie->port, pcie->lane, (u32)pcie->base);
/* Read Id info and local bus/dev */
debug("direct conf read %08x, local bus %d, local dev %d\n",
readl(pcie->base), mvebu_pcie_get_local_bus_nr(pcie),
mvebu_pcie_get_local_dev_nr(pcie));
mvebu_pcie_set_local_bus_nr(pcie, bus);
mvebu_pcie_set_local_dev_nr(pcie, 0);
pcie->dev = PCI_BDF(bus, 0, 0);
pcie->mem.start = (u32)mvebu_pcie_membase;
pcie->mem.end = pcie->mem.start + PCIE_MEM_SIZE - 1;
mvebu_pcie_membase += PCIE_MEM_SIZE;
if (mvebu_mbus_add_window_by_id(mem_target, mem_attr,
(phys_addr_t)pcie->mem.start,
PCIE_MEM_SIZE)) {
printf("PCIe unable to add mbus window for mem at %08x+%08x\n",
(u32)pcie->mem.start, PCIE_MEM_SIZE);
}
/* Setup windows and configure host bridge */
mvebu_pcie_setup_wins(pcie);
/* Master + slave enable. */
reg = readl(pcie->base + PCIE_CMD_OFF);
reg |= PCI_COMMAND_MEMORY;
reg |= PCI_COMMAND_MASTER;
reg |= BIT(10); /* disable interrupts */
writel(reg, pcie->base + PCIE_CMD_OFF);
/* Setup U-Boot PCI Controller */
hose->first_busno = 0;
hose->current_busno = bus;
/* PCI memory space */
pci_set_region(hose->regions + 0, pcie->mem.start,
pcie->mem.start, PCIE_MEM_SIZE, PCI_REGION_MEM);
pci_set_region(hose->regions + 1,
0, 0,
gd->ram_size,
PCI_REGION_MEM | PCI_REGION_SYS_MEMORY);
hose->region_count = 2;
pci_set_ops(hose,
pci_hose_read_config_byte_via_dword,
pci_hose_read_config_word_via_dword,
mvebu_pcie_read_config_dword,
pci_hose_write_config_byte_via_dword,
pci_hose_write_config_word_via_dword,
mvebu_pcie_write_config_dword);
pci_register_hose(hose);
hose->last_busno = pci_hose_scan(hose);
/* Set BAR0 to internal registers */
writel(SOC_REGS_PHY_BASE, pcie->base + PCIE_BAR_LO_OFF(0));
writel(0, pcie->base + PCIE_BAR_HI_OFF(0));
bus = hose->last_busno + 1;
}
}
void pci_mcf5445x_init(struct pci_controller *hose)
{
pci_t *pci = (pci_t *)MMAP_PCI;
pciarb_t *pciarb = (pciarb_t *)MMAP_PCIARB;
gpio_t *gpio = (gpio_t *) MMAP_GPIO;
u32 barEn = 0;
out_be32(&pciarb->acr, 0x001f001f);
/* Set PCIGNT1, PCIREQ1, PCIREQ0/PCIGNTIN, PCIGNT0/PCIREQOUT,
PCIREQ2, PCIGNT2 */
out_be16(&gpio->par_pci,
GPIO_PAR_PCI_GNT3_GNT3 | GPIO_PAR_PCI_GNT2 |
GPIO_PAR_PCI_GNT1 | GPIO_PAR_PCI_GNT0 |
GPIO_PAR_PCI_REQ3_REQ3 | GPIO_PAR_PCI_REQ2 |
GPIO_PAR_PCI_REQ1 | GPIO_PAR_PCI_REQ0);
/* Assert reset bit */
setbits_be32(&pci->gscr, PCI_GSCR_PR);
setbits_be32(&pci->tcr1, PCI_TCR1_P);
/* Initiator windows */
out_be32(&pci->iw0btar,
CONFIG_SYS_PCI_MEM_PHYS | (CONFIG_SYS_PCI_MEM_PHYS >> 16));
out_be32(&pci->iw1btar,
CONFIG_SYS_PCI_IO_PHYS | (CONFIG_SYS_PCI_IO_PHYS >> 16));
out_be32(&pci->iw2btar,
CONFIG_SYS_PCI_CFG_PHYS | (CONFIG_SYS_PCI_CFG_PHYS >> 16));
out_be32(&pci->iwcr,
PCI_IWCR_W0C_EN | PCI_IWCR_W1C_EN | PCI_IWCR_W1C_IO |
PCI_IWCR_W2C_EN | PCI_IWCR_W2C_IO);
out_be32(&pci->icr, 0);
/* Enable bus master and mem access */
out_be32(&pci->scr, PCI_SCR_B | PCI_SCR_M);
/* Cache line size and master latency */
out_be32(&pci->cr1, PCI_CR1_CLS(8) | PCI_CR1_LTMR(0xF8));
out_be32(&pci->cr2, 0);
#ifdef CONFIG_SYS_PCI_BAR0
out_be32(&pci->bar0, PCI_BAR_BAR0(CONFIG_SYS_PCI_BAR0));
out_be32(&pci->tbatr0, CONFIG_SYS_PCI_TBATR0 | PCI_TBATR_EN);
barEn |= PCI_TCR2_B0E;
#endif
#ifdef CONFIG_SYS_PCI_BAR1
out_be32(&pci->bar1, PCI_BAR_BAR1(CONFIG_SYS_PCI_BAR1));
out_be32(&pci->tbatr1, CONFIG_SYS_PCI_TBATR1 | PCI_TBATR_EN);
barEn |= PCI_TCR2_B1E;
#endif
#ifdef CONFIG_SYS_PCI_BAR2
out_be32(&pci->bar2, PCI_BAR_BAR2(CONFIG_SYS_PCI_BAR2));
out_be32(&pci->tbatr2, CONFIG_SYS_PCI_TBATR2 | PCI_TBATR_EN);
barEn |= PCI_TCR2_B2E;
#endif
#ifdef CONFIG_SYS_PCI_BAR3
out_be32(&pci->bar3, PCI_BAR_BAR3(CONFIG_SYS_PCI_BAR3));
out_be32(&pci->tbatr3, CONFIG_SYS_PCI_TBATR3 | PCI_TBATR_EN);
barEn |= PCI_TCR2_B3E;
#endif
#ifdef CONFIG_SYS_PCI_BAR4
out_be32(&pci->bar4, PCI_BAR_BAR4(CONFIG_SYS_PCI_BAR4));
out_be32(&pci->tbatr4, CONFIG_SYS_PCI_TBATR4 | PCI_TBATR_EN);
barEn |= PCI_TCR2_B4E;
#endif
#ifdef CONFIG_SYS_PCI_BAR5
out_be32(&pci->bar5, PCI_BAR_BAR5(CONFIG_SYS_PCI_BAR5));
out_be32(&pci->tbatr5, CONFIG_SYS_PCI_TBATR5 | PCI_TBATR_EN);
barEn |= PCI_TCR2_B5E;
#endif
out_be32(&pci->tcr2, barEn);
/* Deassert reset bit */
clrbits_be32(&pci->gscr, PCI_GSCR_PR);
udelay(1000);
/* Enable PCI bus master support */
hose->first_busno = 0;
hose->last_busno = 0xff;
pci_set_region(hose->regions + 0, CONFIG_SYS_PCI_MEM_BUS, CONFIG_SYS_PCI_MEM_PHYS,
CONFIG_SYS_PCI_MEM_SIZE, PCI_REGION_MEM);
pci_set_region(hose->regions + 1, CONFIG_SYS_PCI_IO_BUS, CONFIG_SYS_PCI_IO_PHYS,
CONFIG_SYS_PCI_IO_SIZE, PCI_REGION_IO);
pci_set_region(hose->regions + 2, CONFIG_SYS_PCI_SYS_MEM_BUS,
CONFIG_SYS_PCI_SYS_MEM_PHYS, CONFIG_SYS_PCI_SYS_MEM_SIZE,
PCI_REGION_MEM | PCI_REGION_SYS_MEMORY);
hose->region_count = 3;
hose->cfg_addr = &(pci->car);
hose->cfg_data = (volatile unsigned char *)CONFIG_SYS_PCI_CFG_BUS;
pci_set_ops(hose, pci_read_cfg_byte, pci_read_cfg_word,
pci_read_cfg_dword, pci_write_cfg_byte, pci_write_cfg_word,
pci_write_cfg_dword);
/* Hose scan */
pci_register_hose(hose);
hose->last_busno = pci_hose_scan(hose);
}
void pci_init_board(void)
{
struct pci_controller* hose = (struct pci_controller *)&local_hose;
u32 reg32;
u16 reg16;
hose->first_busno = 0;
hose->last_busno = 0xff;
pci_set_region(hose->regions + 0,
CFG_PCI_MEMORY_BUS,
CFG_PCI_MEMORY_PHYS,
/*
* Attention: pci_hose_phys_to_bus() failes in address compare,
* so we need (CFG_PCI_MEMORY_SIZE-1)
*/
CFG_PCI_MEMORY_SIZE-1,
PCI_REGION_MEM | PCI_REGION_MEMORY);
/* PCI memory space */
pci_set_region(hose->regions + 1,
CFG_PCI_MEM_BUS,
CFG_PCI_MEM_PHYS,
CFG_PCI_MEM_SIZE,
PCI_REGION_MEM);
/* ISA/PCI memory space */
pci_set_region(hose->regions + 2,
CFG_ISA_MEM_BUS,
CFG_ISA_MEM_PHYS,
CFG_ISA_MEM_SIZE,
PCI_REGION_MEM);
/* PCI I/O space */
pci_set_region(hose->regions + 3,
CFG_PCI_IO_BUS,
CFG_PCI_IO_PHYS,
CFG_PCI_IO_SIZE,
PCI_REGION_IO);
/* ISA/PCI I/O space */
pci_set_region(hose->regions + 4,
CFG_ISA_IO_BUS,
CFG_ISA_IO_PHYS,
CFG_ISA_IO_SIZE,
PCI_REGION_IO);
hose->region_count = 5;
pci_setup_indirect(hose,
MPC106_REG_ADDR,
MPC106_REG_DATA);
pci_register_hose(hose);
hose->last_busno = pci_hose_scan(hose);
/* Initialises the MPC10x PCI Configuration regs. */
pci_read_config_dword (PCI_BDF(0,0,0), PCI_PICR2, ®32);
reg32 |= PICR2_CF_SNOOP_WS(3) |
PICR2_CF_FLUSH_L2 |
PICR2_CF_L2_HIT_DELAY(3) |
PICR2_CF_APHASE_WS(3);
reg32 &= ~(PICR2_L2_EN | PICR2_L2_UPDATE_EN);
pci_write_config_dword (PCI_BDF(0,0,0), PCI_PICR2, reg32);
pci_read_config_word (PCI_BDF(0,0,0), PCI_COMMAND, ®16);
reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
pci_write_config_word(PCI_BDF(0,0,0), PCI_COMMAND, reg16);
/* Clear non-reserved bits in status register */
pci_write_config_word(PCI_BDF(0,0,0), PCI_STATUS, 0xffff);
pci_read_config_dword (PCI_BDF(0,0,0), PCI_PICR1, ®32);
reg32 |= PICR1_CF_CBA(63) |
PICR1_CF_BREAD_WS(2) |
PICR1_MCP_EN |
PICR1_CF_DPARK |
PICR1_PROC_TYPE_604 |
PICR1_CF_LOOP_SNOOP |
PICR1_CF_APARK;
pci_write_config_dword (PCI_BDF(0,0,0), PCI_PICR1, reg32);
}
void
pci_init_board(void)
{
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
uint devdisr = gur->devdisr;
uint io_sel = (gur->pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19;
uint host_agent = (gur->porbmsr & MPC85xx_PORBMSR_HA) >> 16;
debug (" pci_init_board: devdisr=%x, io_sel=%x, host_agent=%x\n",
devdisr, io_sel, host_agent);
/* explicitly set 'Clock out select register' to echo SYSCLK input to our CPLD */
gur->clkocr |= MPC85xx_ATUM_CLKOCR;
if (io_sel & 1) {
if (!(gur->pordevsr & MPC85xx_PORDEVSR_SGMII1_DIS))
printf (" eTSEC1 is in sgmii mode.\n");
if (!(gur->pordevsr & MPC85xx_PORDEVSR_SGMII2_DIS))
printf (" eTSEC2 is in sgmii mode.\n");
if (!(gur->pordevsr & MPC85xx_PORDEVSR_SGMII3_DIS))
printf (" eTSEC3 is in sgmii mode.\n");
if (!(gur->pordevsr & MPC85xx_PORDEVSR_SGMII4_DIS))
printf (" eTSEC4 is in sgmii mode.\n");
}
#ifdef CONFIG_PCIE1
{
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE1_ADDR;
struct pci_controller *hose = &pcie1_hose;
int pcie_ep = (host_agent == 5);
int pcie_configured = io_sel & 6;
struct pci_region *r = hose->regions;
if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE)){
printf ("\n PCIE1 connected to slot as %s (base address %x)",
pcie_ep ? "End Point" : "Root Complex",
(uint)pci);
if (pci->pme_msg_det) {
pci->pme_msg_det = 0xffffffff;
debug (" with errors. Clearing. Now 0x%08x",pci->pme_msg_det);
}
printf ("\n");
/* inbound */
r += fsl_pci_setup_inbound_windows(r);
/* outbound memory */
pci_set_region(r++,
CONFIG_SYS_PCIE1_MEM_BASE,
CONFIG_SYS_PCIE1_MEM_PHYS,
CONFIG_SYS_PCIE1_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
pci_set_region(r++,
CONFIG_SYS_PCIE1_IO_BASE,
CONFIG_SYS_PCIE1_IO_PHYS,
CONFIG_SYS_PCIE1_IO_SIZE,
PCI_REGION_IO);
#ifdef CONFIG_SYS_PCIE1_MEM_BASE2
/* outbound memory */
pci_set_region(r++,
CONFIG_SYS_PCIE1_MEM_BASE2,
CONFIG_SYS_PCIE1_MEM_PHYS2,
CONFIG_SYS_PCIE1_MEM_SIZE2,
PCI_REGION_MEM);
#endif
hose->region_count = r - hose->regions;
hose->first_busno=first_free_busno;
pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
fsl_pci_init(hose);
first_free_busno=hose->last_busno+1;
printf(" PCIE1 on bus %02x - %02x\n",
hose->first_busno,hose->last_busno);
} else {
printf (" PCIE1: disabled\n");
}
}
#else
gur->devdisr |= MPC85xx_DEVDISR_PCIE; /* disable */
#endif
#ifdef CONFIG_PCI1
{
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCI1_ADDR;
struct pci_controller *hose = &pci1_hose;
struct pci_region *r = hose->regions;
uint pci_agent = (host_agent == 6);
uint pci_speed = 33333000; /*get_clock_freq (); PCI PSPEED in [4:5] */
uint pci_32 = gur->pordevsr & MPC85xx_PORDEVSR_PCI1_PCI32; /* PORDEVSR[15] */
uint pci_arb = gur->pordevsr & MPC85xx_PORDEVSR_PCI1_ARB; /* PORDEVSR[14] */
uint pci_clk_sel = gur->porpllsr & MPC85xx_PORDEVSR_PCI1_SPD; /* PORPLLSR[16] */
if (!(devdisr & MPC85xx_DEVDISR_PCI1)) {
printf ("\n PCI1: %d bit, %s MHz, %s, %s, %s (base address %x)\n",
(pci_32) ? 32 : 64,
(pci_speed == 33333000) ? "33" :
(pci_speed == 66666000) ? "66" : "unknown",
pci_clk_sel ? "sync" : "async",
pci_agent ? "agent" : "host",
pci_arb ? "arbiter" : "external-arbiter",
(uint)pci
);
/* inbound */
r += fsl_pci_setup_inbound_windows(r);
/* outbound memory */
pci_set_region(r++,
CONFIG_SYS_PCI1_MEM_BASE,
CONFIG_SYS_PCI1_MEM_PHYS,
CONFIG_SYS_PCI1_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
pci_set_region(r++,
CONFIG_SYS_PCI1_IO_BASE,
CONFIG_SYS_PCI1_IO_PHYS,
CONFIG_SYS_PCI1_IO_SIZE,
PCI_REGION_IO);
hose->region_count = r - hose->regions;
hose->first_busno=first_free_busno;
pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
fsl_pci_init(hose);
first_free_busno=hose->last_busno+1;
printf ("PCI1 on bus %02x - %02x\n",
hose->first_busno,hose->last_busno);
} else {
printf (" PCI1: disabled\n");
}
}
#else
gur->devdisr |= MPC85xx_DEVDISR_PCI1; /* disable */
#endif
#ifdef CONFIG_PCI2
{
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCI2_ADDR;
struct pci_controller *hose = &pci2_hose;
struct pci_region *r = hose->regions;
if (!(devdisr & MPC85xx_DEVDISR_PCI2)) {
r += fsl_pci_setup_inbound_windows(r);
pci_set_region(r++,
CONFIG_SYS_PCI2_MEM_BASE,
CONFIG_SYS_PCI2_MEM_PHYS,
CONFIG_SYS_PCI2_MEM_SIZE,
PCI_REGION_MEM);
pci_set_region(r++,
CONFIG_SYS_PCI2_IO_BASE,
CONFIG_SYS_PCI2_IO_PHYS,
CONFIG_SYS_PCI2_IO_SIZE,
PCI_REGION_IO);
hose->region_count = r - hose->regions;
hose->first_busno=first_free_busno;
pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
fsl_pci_init(hose);
first_free_busno=hose->last_busno+1;
printf ("PCI2 on bus %02x - %02x\n",
hose->first_busno,hose->last_busno);
} else {
printf (" PCI2: disabled\n");
}
}
#else
gur->devdisr |= MPC85xx_DEVDISR_PCI2;
#endif
}
void pcie_setup_hoses(int busno)
{
struct pci_controller *hose;
int i, bus;
int ret = 0;
char *env;
unsigned int delay;
/*
* assume we're called after the PCIX hose is initialized, which takes
* bus ID 0 and therefore start numbering PCIe's from 1.
*/
bus = busno;
for (i = 0; i <= 2; i++) {
/* Check for katmai card presence */
if (!katmai_pcie_card_present(i))
continue;
if (is_end_point(i))
ret = ppc4xx_init_pcie_endport(i);
else
ret = ppc4xx_init_pcie_rootport(i);
if (ret) {
printf("PCIE%d: initialization as %s failed\n", i,
is_end_point(i) ? "endpoint" : "root-complex");
continue;
}
hose = &pcie_hose[i];
hose->first_busno = bus;
hose->last_busno = bus;
hose->current_busno = bus;
/* setup mem resource */
pci_set_region(hose->regions + 0,
CONFIG_SYS_PCIE_MEMBASE + i * CONFIG_SYS_PCIE_MEMSIZE,
CONFIG_SYS_PCIE_MEMBASE + i * CONFIG_SYS_PCIE_MEMSIZE,
CONFIG_SYS_PCIE_MEMSIZE,
PCI_REGION_MEM);
hose->region_count = 1;
pci_register_hose(hose);
if (is_end_point(i)) {
ppc4xx_setup_pcie_endpoint(hose, i);
/*
* Reson for no scanning is endpoint can not generate
* upstream configuration accesses.
*/
} else {
ppc4xx_setup_pcie_rootpoint(hose, i);
env = getenv ("pciscandelay");
if (env != NULL) {
delay = simple_strtoul(env, NULL, 10);
if (delay > 5)
printf("Warning, expect noticable delay before "
"PCIe scan due to 'pciscandelay' value!\n");
mdelay(delay * 1000);
}
/*
* Config access can only go down stream
*/
hose->last_busno = pci_hose_scan(hose);
bus = hose->last_busno + 1;
}
}
}
void pci_mpc8250_init (struct pci_controller *hose)
{
u16 tempShort;
volatile immap_t *immap = (immap_t *) CFG_IMMR;
pci_dev_t host_devno = PCI_BDF (0, 0, 0);
pci_setup_indirect (hose, CFG_IMMR + PCI_CFG_ADDR_REG,
CFG_IMMR + PCI_CFG_DATA_REG);
/*
* Setting required to enable local bus for PCI (SIUMCR [LBPC]).
*/
#ifdef CONFIG_MPC8266ADS
immap->im_siu_conf.sc_siumcr =
(immap->im_siu_conf.sc_siumcr & ~SIUMCR_LBPC11)
| SIUMCR_LBPC01;
#elif defined CONFIG_MPC8272
immap->im_siu_conf.sc_siumcr = (immap->im_siu_conf.sc_siumcr &
~SIUMCR_BBD &
~SIUMCR_ESE &
~SIUMCR_PBSE &
~SIUMCR_CDIS &
~SIUMCR_DPPC11 &
~SIUMCR_L2CPC11 &
~SIUMCR_LBPC11 &
~SIUMCR_APPC11 &
~SIUMCR_CS10PC11 &
~SIUMCR_BCTLC11 &
~SIUMCR_MMR11)
| SIUMCR_DPPC11
| SIUMCR_L2CPC01
| SIUMCR_LBPC00
| SIUMCR_APPC10
| SIUMCR_CS10PC00
| SIUMCR_BCTLC00
| SIUMCR_MMR11;
#elif defined(CONFIG_TQM8272)
/* nothing to do for this Board here */
#else
/*
* Setting required to enable IRQ1-IRQ7 (SIUMCR [DPPC]),
* and local bus for PCI (SIUMCR [LBPC]).
*/
immap->im_siu_conf.sc_siumcr = (immap->im_siu_conf.sc_siumcr &
~SIUMCR_LBPC11 &
~SIUMCR_CS10PC11 &
~SIUMCR_LBPC11) |
SIUMCR_LBPC01 |
SIUMCR_CS10PC01 |
SIUMCR_APPC10;
#endif
/* Make PCI lowest priority */
/* Each 4 bits is a device bus request and the MS 4bits
is highest priority */
/* Bus 4bit value
--- ----------
CPM high 0b0000
CPM middle 0b0001
CPM low 0b0010
PCI reguest 0b0011
Reserved 0b0100
Reserved 0b0101
Internal Core 0b0110
External Master 1 0b0111
External Master 2 0b1000
External Master 3 0b1001
The rest are reserved */
immap->im_siu_conf.sc_ppc_alrh = 0x61207893;
/* Park bus on core while modifying PCI Bus accesses */
immap->im_siu_conf.sc_ppc_acr = 0x6;
/*
* Set up master windows that allow the CPU to access PCI space. These
* windows are set up using the two SIU PCIBR registers.
*/
immap->im_memctl.memc_pcimsk0 = PCIMSK0_MASK;
immap->im_memctl.memc_pcibr0 = PCI_MSTR0_LOCAL | PCIBR_ENABLE;
#if defined CONFIG_MPC8266ADS || defined CONFIG_MPC8272
immap->im_memctl.memc_pcimsk1 = PCIMSK1_MASK;
immap->im_memctl.memc_pcibr1 = PCI_MSTR1_LOCAL | PCIBR_ENABLE;
#endif
/* Release PCI RST (by default the PCI RST signal is held low) */
immap->im_pci.pci_gcr = cpu_to_le32 (PCIGCR_PCI_BUS_EN);
/* give it some time */
{
#if defined CONFIG_MPC8266ADS || defined CONFIG_MPC8272
/* Give the PCI cards more time to initialize before query
This might be good for other boards also
*/
int i;
for (i = 0; i < 1000; ++i)
#endif
udelay (1000);
}
/*
* Set up master window that allows the CPU to access PCI Memory (prefetch)
* space. This window is set up using the first set of Outbound ATU registers.
*/
immap->im_pci.pci_potar0 = cpu_to_le32 (PCI_MSTR_MEM_BUS >> 12); /* PCI base */
immap->im_pci.pci_pobar0 = cpu_to_le32 (PCI_MSTR_MEM_LOCAL >> 12); /* Local base */
immap->im_pci.pci_pocmr0 = cpu_to_le32 (POCMR0_MASK_ATTRIB); /* Size & attribute */
/*
* Set up master window that allows the CPU to access PCI Memory (non-prefetch)
* space. This window is set up using the second set of Outbound ATU registers.
*/
immap->im_pci.pci_potar1 = cpu_to_le32 (PCI_MSTR_MEMIO_BUS >> 12); /* PCI base */
immap->im_pci.pci_pobar1 = cpu_to_le32 (PCI_MSTR_MEMIO_LOCAL >> 12); /* Local base */
immap->im_pci.pci_pocmr1 = cpu_to_le32 (POCMR1_MASK_ATTRIB); /* Size & attribute */
/*
* Set up master window that allows the CPU to access PCI IO space. This window
* is set up using the third set of Outbound ATU registers.
*/
immap->im_pci.pci_potar2 = cpu_to_le32 (PCI_MSTR_IO_BUS >> 12); /* PCI base */
immap->im_pci.pci_pobar2 = cpu_to_le32 (PCI_MSTR_IO_LOCAL >> 12); /* Local base */
immap->im_pci.pci_pocmr2 = cpu_to_le32 (POCMR2_MASK_ATTRIB); /* Size & attribute */
/*
* Set up slave window that allows PCI masters to access MPC826x local memory.
* This window is set up using the first set of Inbound ATU registers
*/
immap->im_pci.pci_pitar0 = cpu_to_le32 (PCI_SLV_MEM_LOCAL >> 12); /* PCI base */
immap->im_pci.pci_pibar0 = cpu_to_le32 (PCI_SLV_MEM_BUS >> 12); /* Local base */
immap->im_pci.pci_picmr0 = cpu_to_le32 (PICMR0_MASK_ATTRIB); /* Size & attribute */
/* See above for description - puts PCI request as highest priority */
#ifdef CONFIG_MPC8272
immap->im_siu_conf.sc_ppc_alrh = 0x01236745;
#else
immap->im_siu_conf.sc_ppc_alrh = 0x03124567;
#endif
/* Park the bus on the PCI */
immap->im_siu_conf.sc_ppc_acr = PPC_ACR_BUS_PARK_PCI;
/* Host mode - specify the bridge as a host-PCI bridge */
pci_hose_write_config_byte (hose, host_devno, PCI_CLASS_CODE,
PCI_CLASS_BRIDGE_CTLR);
/* Enable the host bridge to be a master on the PCI bus, and to act as a PCI memory target */
pci_hose_read_config_word (hose, host_devno, PCI_COMMAND, &tempShort);
pci_hose_write_config_word (hose, host_devno, PCI_COMMAND,
tempShort | PCI_COMMAND_MASTER |
PCI_COMMAND_MEMORY);
/* do some bridge init, should be done on all 8260 based bridges */
pci_hose_write_config_byte (hose, host_devno, PCI_CACHE_LINE_SIZE,
0x08);
pci_hose_write_config_byte (hose, host_devno, PCI_LATENCY_TIMER,
0xF8);
hose->first_busno = 0;
hose->last_busno = 0xff;
/* System memory space */
#if defined CONFIG_MPC8266ADS || defined CONFIG_MPC8272 || defined CONFIG_PM826
pci_set_region (hose->regions + 0,
PCI_SLV_MEM_BUS,
PCI_SLV_MEM_LOCAL,
gd->ram_size, PCI_REGION_MEM | PCI_REGION_MEMORY);
#else
pci_set_region (hose->regions + 0,
CFG_SDRAM_BASE,
CFG_SDRAM_BASE,
0x4000000, PCI_REGION_MEM | PCI_REGION_MEMORY);
#endif
/* PCI memory space */
#if defined CONFIG_MPC8266ADS || defined CONFIG_MPC8272
pci_set_region (hose->regions + 1,
PCI_MSTR_MEMIO_BUS,
PCI_MSTR_MEMIO_LOCAL,
PCI_MSTR_MEMIO_SIZE, PCI_REGION_MEM);
#else
pci_set_region (hose->regions + 1,
PCI_MSTR_MEM_BUS,
PCI_MSTR_MEM_LOCAL,
PCI_MSTR_MEM_SIZE, PCI_REGION_MEM);
#endif
/* PCI I/O space */
pci_set_region (hose->regions + 2,
PCI_MSTR_IO_BUS,
PCI_MSTR_IO_LOCAL, PCI_MSTR_IO_SIZE, PCI_REGION_IO);
hose->region_count = 3;
pci_register_hose (hose);
/* Mask off master abort machine checks */
immap->im_pci.pci_emr &= cpu_to_le32 (~PCI_ERROR_PCI_NO_RSP);
eieio ();
hose->last_busno = pci_hose_scan (hose);
/* clear the error in the error status register */
immap->im_pci.pci_esr = cpu_to_le32 (PCI_ERROR_PCI_NO_RSP);
/* unmask master abort machine checks */
immap->im_pci.pci_emr |= cpu_to_le32 (PCI_ERROR_PCI_NO_RSP);
}
static int fsl_pci_setup_inbound_windows(struct pci_controller *hose,
u64 out_lo, u8 pcie_cap,
volatile pit_t *pi)
{
struct pci_region *r = hose->regions + hose->region_count;
u64 sz = min((u64)gd->ram_size, (1ull << 32));
phys_addr_t phys_start = CONFIG_SYS_PCI_MEMORY_PHYS;
pci_addr_t bus_start = CONFIG_SYS_PCI_MEMORY_BUS;
pci_size_t pci_sz;
/* we have no space available for inbound memory mapping */
if (bus_start > out_lo) {
printf ("no space for inbound mapping of memory\n");
return 0;
}
/* limit size */
if ((bus_start + sz) > out_lo) {
sz = out_lo - bus_start;
debug ("limiting size to %llx\n", sz);
}
pci_sz = 1ull << __ilog2_u64(sz);
/*
* we can overlap inbound/outbound windows on PCI-E since RX & TX
* links a separate
*/
if ((pcie_cap == PCI_CAP_ID_EXP) && (pci_sz < sz)) {
debug ("R0 bus_start: %llx phys_start: %llx size: %llx\n",
(u64)bus_start, (u64)phys_start, (u64)sz);
pci_set_region(r, bus_start, phys_start, sz,
PCI_REGION_MEM | PCI_REGION_SYS_MEMORY |
PCI_REGION_PREFETCH);
/* if we aren't an exact power of two match, pci_sz is smaller
* round it up to the next power of two. We report the actual
* size to pci region tracking.
*/
if (pci_sz != sz)
sz = 2ull << __ilog2_u64(sz);
set_inbound_window(pi--, r++, sz);
sz = 0; /* make sure we dont set the R2 window */
} else {
debug ("R0 bus_start: %llx phys_start: %llx size: %llx\n",
(u64)bus_start, (u64)phys_start, (u64)pci_sz);
pci_set_region(r, bus_start, phys_start, pci_sz,
PCI_REGION_MEM | PCI_REGION_SYS_MEMORY |
PCI_REGION_PREFETCH);
set_inbound_window(pi--, r++, pci_sz);
sz -= pci_sz;
bus_start += pci_sz;
phys_start += pci_sz;
pci_sz = 1ull << __ilog2_u64(sz);
if (sz) {
debug ("R1 bus_start: %llx phys_start: %llx size: %llx\n",
(u64)bus_start, (u64)phys_start, (u64)pci_sz);
pci_set_region(r, bus_start, phys_start, pci_sz,
PCI_REGION_MEM | PCI_REGION_SYS_MEMORY |
PCI_REGION_PREFETCH);
set_inbound_window(pi--, r++, pci_sz);
sz -= pci_sz;
bus_start += pci_sz;
phys_start += pci_sz;
}
}
#if defined(CONFIG_PHYS_64BIT) && defined(CONFIG_SYS_PCI_64BIT)
/*
* On 64-bit capable systems, set up a mapping for all of DRAM
* in high pci address space.
*/
pci_sz = 1ull << __ilog2_u64(gd->ram_size);
/* round up to the next largest power of two */
if (gd->ram_size > pci_sz)
pci_sz = 1ull << (__ilog2_u64(gd->ram_size) + 1);
debug ("R64 bus_start: %llx phys_start: %llx size: %llx\n",
(u64)CONFIG_SYS_PCI64_MEMORY_BUS,
(u64)CONFIG_SYS_PCI_MEMORY_PHYS,
(u64)pci_sz);
pci_set_region(r,
CONFIG_SYS_PCI64_MEMORY_BUS,
CONFIG_SYS_PCI_MEMORY_PHYS,
pci_sz,
PCI_REGION_MEM | PCI_REGION_SYS_MEMORY |
PCI_REGION_PREFETCH);
set_inbound_window(pi--, r++, pci_sz);
#else
pci_sz = 1ull << __ilog2_u64(sz);
if (sz) {
debug ("R2 bus_start: %llx phys_start: %llx size: %llx\n",
(u64)bus_start, (u64)phys_start, (u64)pci_sz);
pci_set_region(r, bus_start, phys_start, pci_sz,
PCI_REGION_MEM | PCI_REGION_SYS_MEMORY |
PCI_REGION_PREFETCH);
sz -= pci_sz;
bus_start += pci_sz;
phys_start += pci_sz;
set_inbound_window(pi--, r++, pci_sz);
}
#endif
#ifdef CONFIG_PHYS_64BIT
if (sz && (((u64)gd->ram_size) < (1ull << 32)))
printf("Was not able to map all of memory via "
"inbound windows -- %lld remaining\n", sz);
#endif
hose->region_count = r - hose->regions;
return 1;
}
