int main(void)
{
/* USER CODE BEGIN 1 */
/* USER CODE END 1 */
/* MCU Configuration----------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* Configure the system clock */
SystemClock_Config();
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_DMA_Init();
MX_I2C3_Init();
MX_TIM1_Init();
MX_TIM2_Init();
MX_TIM3_Init();
MX_TIM4_Init();
MX_TIM5_Init();
MX_USART1_UART_Init();
MX_USART2_UART_Init();
MX_TIM11_Init();
/* USER CODE BEGIN 2 */
HAL_TIM_Base_Start_IT(&htim11); // 100 msec timer
initSonar( MAX_SONAR);
initSerOutput();
/* USER CODE END 2 */
/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
{
/* USER CODE END WHILE */
/* USER CODE BEGIN 3 */
// >>>>> Sonar reading
triggerSonar( COUPLE_0_2);
HAL_Delay(49);
triggerSonar( COUPLE_1_3);
HAL_Delay(49);
// <<<<< Sonar reading
// >>>>> Serial Output
convertMeasures();
sendMeasures();
// <<<<< Serial Output
}
/* USER CODE END 3 */
}
int main(void)
{
/* USER CODE BEGIN 1 */
/* USER CODE END 1 */
/* MCU Configuration----------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* Configure the system clock */
SystemClock_Config();
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_DMA_Init();
MX_ADC1_Init();
MX_I2C1_Init();
MX_RTC_Init();
MX_SPI2_Init();
MX_TIM1_Init();
MX_TIM2_Init();
MX_TIM3_Init();
MX_TIM4_Init();
MX_USART3_UART_Init();
/* USER CODE BEGIN 2 */
encoderInit();
pwmInit();
// adcInit();
uartInit();
timInterruptInit();
gyroInit(GYROHIGH);
calibrateGyro();
// rotaryRight(800);
// HAL_Delay(500);
// rotaryLeft(800);
drive(VEL);
/* USER CODE END 2 */
/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
{
/* USER CODE END WHILE */
/* USER CODE BEGIN 3 */
}
/* USER CODE END 3 */
}
int main(void) {
HAL_Init();
Nucleo_BSP_Init();
MX_TIM3_Init();
HAL_TIM_Base_Start_IT(&htim3);
while (1);
}
int main(void) {
HAL_Init();
Nucleo_BSP_Init();
MX_TIM3_Init();
HAL_TIM_OnePulse_Start(&htim3, TIM_CHANNEL_1);
while (1);
}
// --- Load and start FE PWM ---
void startPWM_FE(uint16_t period, uint16_t width)
{
// Setup PWM timer
MX_TIM3_Init();
htim3.Instance->CCR3 = width;
htim3.Init.Period = period;
HAL_TIM_Base_Init(&htim3);
HAL_TIM_PWM_Start(&htim3, TIM_CHANNEL_3);
}
int main(void)
{
int autorun;
// double calcfreq;
// double CurrentFreq = 144e6;
/* MCU Configuration----------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* Configure the system clock */
SystemClock_Config();
/* Initialize all configured peripherals */
MX_GPIO_Init();
//MX_SPI1_Init();
HAL_GPIO_WritePin(GPIOB, GPIO_PIN_1, GPIO_PIN_SET);
MX_TIM3_Init();
MX_TIM14_Init();
MX_USB_DEVICE_Init();
Morse_Init();
// prepare_pll();
// UpdateFrequencyRegisters(CurrentFreq, 50000000.0, 5000, 1, 1, &calcfreq);
// PLL_Sync();
autorun = cmd_isautorun() ;
/* Infinite loop */
while (1)
{
if (is_line_received())
{
// Process received line
cmd_proc(get_line_buffer());
}
HAL_Delay(10); ar_count++;
if ((ar_count > 1000) & (autorun>0))
{
// Start Autorun
cmd_autorun(autorun);
cw_autorunning = 1;
while(cw_autorunning) HAL_Delay(10);
}
}
}
int main(void)
{
/* USER CODE BEGIN 1 */
SCB->VTOR = FLASH_START_SECTOR_ADDR;
SEGGER_RTT_Init();
/* USER CODE END 1 */
/* MCU Configuration----------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* Configure the system clock */
SystemClock_Config();
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_ADC1_Init();
MX_I2C1_Init();
MX_I2C2_Init();
MX_SPI1_Init();
MX_TIM3_Init();
MX_USART2_UART_Init();
MX_RTC_Init();
/* USER CODE BEGIN 2 */
//as7000_init();
/* USER CODE END 2 */
/* Call init function for freertos objects (in freertos.c) */
MX_FREERTOS_Init();
/* Start scheduler */
osKernelStart();
/* We should never get here as control is now taken by the scheduler */
/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
{
/* USER CODE END WHILE */
/* USER CODE BEGIN 3 */
}
/* USER CODE END 3 */
}
int main(void)
{
/* USER CODE BEGIN 1 */
/* USER CODE END 1 */
/* MCU Configuration----------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* Configure the system clock */
SystemClock_Config();
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_COMP1_Init();
MX_COMP2_Init();
MX_I2C1_Init();
MX_TIM3_Init();
MX_USART1_UART_Init();
MX_ADC_Init();
MX_DMA_Init();
/* USER CODE BEGIN 2 */
init_all();
/* USER CODE END 2 */
/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
{
period_time_check_flags();
// if (HAL_GPIO_ReadPin(GPIOB, GPIO_PIN_4) != GPIO_PIN_RESET)
// {
// HAL_GPIO_TogglePin(GPIOC, GPIO_PIN_10);
// buzzer(beeps,1);
// buzzer_speed(100);
// }
/* USER CODE END WHILE */
/* USER CODE BEGIN 3 */
speed_counter++;
}
/* USER CODE END 3 */
}
int main(void)
{
/* USER CODE BEGIN 1 */
/* USER CODE END 1 */
/* MCU Configuration----------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* Configure the system clock */
SystemClock_Config();
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_DMA_Init();
MX_SPI1_Init();
MX_TIM2_Init();
MX_TIM3_Init();
MX_TIM7_Init();
MX_TIM10_Init();
MX_TIM11_Init();
MX_TIM13_Init();
MX_TIM14_Init();
MX_USART1_UART_Init();
MX_USART2_UART_Init();
/* USER CODE BEGIN 2 */
HAL_TIM_PWM_Start(&htim2, TIM_CHANNEL_1); //Motor1
HAL_TIM_PWM_Start(&htim2, TIM_CHANNEL_4); //Motor2
HAL_TIM_PWM_Start(&htim3, TIM_CHANNEL_1); //Motor3
HAL_TIM_PWM_Start(&htim3, TIM_CHANNEL_4); //Motor4
/* USER CODE END 2 */
/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
{
/* USER CODE END WHILE */
/* USER CODE BEGIN 3 */
}
/* USER CODE END 3 */
}
int main(void)
{
/* USER CODE BEGIN 1 */
/* USER CODE END 1 */
/* MCU Configuration----------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* Configure the system clock */
SystemClock_Config();
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_DMA_Init();
MX_ADC1_Init();
MX_I2C1_Init();
MX_IWDG_Init();
MX_SDADC1_Init();
MX_SDADC2_Init();
MX_TSC_Init();
MX_TIM2_Init();
MX_TIM3_Init();
MX_SDADC3_Init();
MX_USB_DEVICE_Init();
MX_RTC_Init();
MX_TIM6_Init();
MX_TIM7_Init();
/* USER CODE BEGIN 2 */
Setup();
/* USER CODE END 2 */
/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
{
/* USER CODE END WHILE */
/* USER CODE BEGIN 3 */
loop();
}
/* USER CODE END 3 */
}
int main(void)
{
USB_HIDDEVICE_Keyboard_t Keyboard_Data;
/* USER CODE BEGIN 1 */
/* USER CODE END 1 */
/* MCU Configuration----------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* Configure the system clock */
SystemClock_Config();
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_TIM3_Init();
MX_USB_DEVICE_Init();
/* USER CODE BEGIN 2 */
/* USER CODE END 2 */
/* Infinite loop */
/* USER CODE BEGIN WHILE */
delay_ms(1000);
// MX_USB_DEVICE_SendHIDAction(0x01);
USB_HIDDEVICE_KeyboardStructInit(&Keyboard_Data);
Keyboard_Data.Key1 = 0x01;
USB_HIDDEVICE_KeyboardSend(&Keyboard_Data);
while (1)
{
/* USER CODE END WHILE */
/* USER CODE BEGIN 3 */
}
/* USER CODE END 3 */
}
int main(void)
{
/* USER CODE BEGIN 1 */
/* USER CODE END 1 */
/* MCU Configuration----------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* Configure the system clock */
SystemClock_Config();
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_DMA_Init();
MX_USART2_UART_Init();
MX_USART3_UART_Init();
MX_TIM3_Init();
/* USER CODE BEGIN 2 */
HAL_TIM_Base_Start_IT(&htim3);
HAL_UART_Transmit_DMA(&huart3,g_cUart3_Buff,BUFFSIZE);
/* USER CODE END 2 */
/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
{
/* USER CODE END WHILE */
HAL_UART_Receive_DMA(&huart3,g_cUart3_Buff,BUFFSIZE);
//HAL_UART_Transmit_IT(&huart3,g_cUart3_Buff,5);
/* USER CODE BEGIN 3 */
}
/* USER CODE END 3 */
}
int main(void) {
uint16_t IV[200];
float angle;
HAL_Init();
Nucleo_BSP_Init();
MX_TIM3_Init();
for (uint8_t i = 0; i < 200; i++) {
angle = ASR*(float)i;
IV[i] = (uint16_t) rint(100 + 99*sinf(angle*(PI/180)));
}
HAL_TIM_PWM_Start_DMA(&htim3, TIM_CHANNEL_1, (uint32_t *)IV, 200);
while (1);
}
int main(void)
{
/* USER CODE BEGIN 1 */
/* USER CODE END 1 */
/* MCU Configuration----------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* Configure the system clock */
SystemClock_Config();
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_I2C1_Init();
MX_TIM1_Init();
MX_TIM3_Init();
MX_ADC1_Init();
MX_TIM2_Init();
/* USER CODE BEGIN 2 */
//Start PWM
HAL_TIM_Base_Start(&htim1);
HAL_TIM_PWM_Start(&htim1, TIM_CHANNEL_ALL);
/* USER CODE END 2 */
/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
{
HAL_GPIO_TogglePin(GPIOA, GPIO_PIN_5);
HAL_Delay(100);
/* USER CODE END WHILE */
/* USER CODE BEGIN 3 */
}
/* USER CODE END 3 */
}
int main(void)
{
/* USER CODE BEGIN 1 */
/* USER CODE END 1 */
/* MCU Configuration----------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* Configure the system clock */
SystemClock_Config();
/* System interrupt init*/
/* Sets the priority grouping field */
HAL_NVIC_SetPriorityGrouping(NVIC_PRIORITYGROUP_0);
HAL_NVIC_SetPriority(SysTick_IRQn, 0, 0);
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_DMA_Init();
MX_I2C1_Init();
MX_I2S2_Init();
MX_I2S3_Init();
MX_SPI1_Init();
MX_SPI4_Init();
MX_TIM3_Init();
MX_USART2_UART_Init();
MX_USB_DEVICE_Init();
/* USER CODE BEGIN 2 */
/* USER CODE END 2 */
/*## FatFS: Link the USER disk I/O driver ###############################*/
USER_DriverNum = FATFS_LinkDriver(&USER_Driver, USER_Path);
/* USER CODE BEGIN 3 */
dabstick_loop(); // endless
return 0;
/* USER CODE END 3 */
}
int main(void)
{
/* USER CODE BEGIN 1 */
/* USER CODE END 1 */
/* MCU Configuration----------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* Configure the system clock */
SystemClock_Config();
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_DMA_Init();
MX_ADC1_Init();
MX_ADC2_Init();
MX_DAC_Init();
MX_TIM2_Init();
MX_TIM3_Init();
/* USER CODE BEGIN 2 */
configure_modem();
acquisition_init();
acquisition_start();
/* USER CODE END 2 */
/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
{
/* USER CODE END WHILE */
/* USER CODE BEGIN 3 */
}
/* USER CODE END 3 */
}
int main(void)
{
/* USER CODE BEGIN 1 */
/* USER CODE END 1 */
/* MCU Configuration----------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* Configure the system clock */
SystemClock_Config();
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_USART1_UART_Init();
MX_SPI1_Init();
MX_TIM1_Init();
MX_TIM3_Init();
HAL_TIM_Base_Start(&htim1);
static char buf[50];
NRF24L01_Reset();
NRF24L01_Initialize();
HAL_Delay(150);
CX10_init();
HAL_Delay(50);
CX10_bind();
while (1) {
process_CX10();
HAL_Delay(6);
}
}
int main(void)
{
/* USER CODE BEGIN 1 */
/* USER CODE END 1 */
/* MCU Configuration----------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* Configure the system clock */
SystemClock_Config();
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_ADC1_Init();
MX_ADC2_Init();
MX_TIM3_Init();
MX_TIM5_Init();
MX_USART2_UART_Init();
MX_USART3_UART_Init();
MX_USB_OTG_FS_PCD_Init();
/* USER CODE BEGIN 2 */
/* USER CODE END 2 */
/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
{
/* USER CODE END WHILE */
/* USER CODE BEGIN 3 */
}
/* USER CODE END 3 */
}
int main(void)
{
/* USER CODE BEGIN 1 */
/* USER CODE END 1 */
/* MCU Configuration----------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* Configure the system clock */
SystemClock_Config();
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_RTC_Init();
//if(!(*(volatile uint32_t *) (BDCR_RTCEN_BB)))__HAL_RCC_RTC_ENABLE();
MX_TIM2_Init();
MX_TIM3_Init();
MX_USART1_UART_Init();
MX_USART2_UART_Init();
/* USER CODE BEGIN 2 */
/* USER CODE END 2 */
/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
{
/* USER CODE END WHILE */
/* USER CODE BEGIN 3 */
HAL_RTC_GetTime(&hrtc, &myTime, FORMAT_BIN);
HAL_RTC_GetDate(&hrtc, &myDate, FORMAT_BIN);
}
/* USER CODE END 3 */
}
int main(void)
{
/* USER CODE BEGIN 1 */
/* USER CODE END 1 */
/* MCU Configuration----------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* Configure the system clock */
SystemClock_Config();
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_TIM3_Init();
MX_USB_DEVICE_Init();
/* USER CODE BEGIN 2 */
HAL_TIM_IC_Start_IT(&htim3, TIM_CHANNEL_1);
/* USER CODE END 2 */
/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
{
/* USER CODE END WHILE */
/* USER CODE BEGIN 3 */
if (data_ready)
{
USBD_HID_SendReport(&hUsbDeviceFS, (uint8_t*)rc_data, 10);
data_ready = 0;
}
}
/* USER CODE END 3 */
}
/* --- AOS Initialization --- */
void AOS_init(void)
{
/* MCU Configuration */
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* Configure the system clock */
SystemClock_Config();
/* Unlock the Flash Program Erase controller */
//HAL_FLASH_Unlock();
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_UART_Init();
MX_TIM2_Init();
MX_TIM7_Init();
/* PWM Timers will override P1, P3 & P4 */
MX_TIM3_Init();
MX_TIM15_Init();
#ifndef TX
MX_ADC_Init();
#endif
/* AOS Initialization */
/* Startup indicator sequence */
blink(500);
HAL_Delay(100);
blink(100);
HAL_Delay(100);
blink(100);
/* Initialize random seed for PRNG */
srand(atoi(_firmTime));
}
void board_Init(void)
{
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* Init Timer */
timer_init();
/* Configure the system clock */
SystemClock_Config();
/* Initialize all configured peripherals */
LED_Init();
MX_GPIO_Init();
//MX_I2C1_Init(); /* TODO: Init */
MX_I2C2_Init();
MX_SPI2_Init();
MX_SPI3_Init();
MX_TIM1_Init();
MX_TIM3_Init();
eUARTInit(&xUARTHandle, uartUARTx);
}
int main(void) {
HAL_Init();
Nucleo_BSP_Init();
MX_TIM3_Init();
HAL_TIM_PWM_Start(&htim3, TIM_CHANNEL_1);
/* Connect a LED to PA6 pin to see the fading effect */
uint16_t dutyCycle = HAL_TIM_ReadCapturedValue(&htim3, TIM_CHANNEL_1);
while(1) {
while(dutyCycle < __HAL_TIM_GET_AUTORELOAD(&htim3)) {
__HAL_TIM_SET_COMPARE(&htim3, TIM_CHANNEL_1, ++dutyCycle);
HAL_Delay(1);
}
while(dutyCycle > 0) {
__HAL_TIM_SET_COMPARE(&htim3, TIM_CHANNEL_1, --dutyCycle);
HAL_Delay(1);
}
}
}
int main(void)
{
/* USER CODE BEGIN 1 */
/* USER CODE END 1 */
/* MCU Configuration----------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* Configure the system clock */
SystemClock_Config();
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_TIM3_Init();
HAL_TIM_Base_Start_IT(&htim3);
HAL_GPIO_WritePin(GPIOA, GPIO_PIN_5|GPIO_PIN_6, GPIO_PIN_RESET);
/* USER CODE BEGIN 2 */
/* USER CODE END 2 */
/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
{
/* USER CODE END WHILE */
/* USER CODE BEGIN 3 */
}
/* USER CODE END 3 */
}
/**
* @brief The application entry point.
*
* @retval None
*/
int main(void)
{
/* USER CODE BEGIN 1 */
/* USER CODE END 1 */
/* MCU Configuration----------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* USER CODE BEGIN Init */
/* USER CODE END Init */
/* Configure the system clock */
SystemClock_Config();
/* USER CODE BEGIN SysInit */
/* USER CODE END SysInit */
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_I2C1_Init();
MX_TIM3_Init();
//MX_IWDG_Init();
MX_TIM14_Init();
MX_TIM16_Init();
MX_TIM17_Init();
/* USER CODE BEGIN 2 */
HAL_TIM_Encoder_Start(&htim3, TIM_CHANNEL_ALL);
HAL_NVIC_SetPriority(TIM3_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(TIM3_IRQn);
HAL_TIM_Base_Start_IT(&htim3);
// Seconds Counter startup duty
HAL_TIM_Base_Start_IT(&htim14);
HAL_TIM_Base_Stop_IT(&htim14);
HAL_TIM_Base_Start_IT(&htim16);
HAL_TIM_Base_Start_IT(&htim17);
HAL_GPIO_WritePin(GPIOA, LED_RED_PIN, GPIO_PIN_RESET);
ssd1306_Init();
current_cursor = exposition;
/* USER CODE END 2 */
/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
{
/* USER CODE END WHILE */
/* USER CODE BEGIN 3 */
//HAL_IWDG_Refresh(&hiwdg);
if(__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_HSE) HAL_GPIO_WritePin(GPIOA, LED_GREEN_PIN, GPIO_PIN_SET);
else HAL_GPIO_WritePin(GPIOA, LED_GREEN_PIN, GPIO_PIN_RESET);
if (update_screen_flag)
{
ssd1306_Fill(Black);
ssd1306_UpdateScreen();
update_screen_flag = 0;
}
if (seconds_counter > STOP_TIME_SEC) //if more than 10 s need to stop
{
// Entering STOP Mode Procedure
seconds_counter = 0;
GPIO_InitTypeDef GPIO_InitStruct;
ssd1306_WriteCommand(0xAE); // OLED Off
GPIO_InitStruct.Pin = ENC_BUTTON_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_EVT_RISING_FALLING;
GPIO_InitStruct.Pull = GPIO_PULLDOWN;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
HAL_NVIC_SetPriority(EXTI4_15_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(EXTI4_15_IRQn);
HAL_GPIO_WritePin(GPIOA, LED_GREEN_PIN|LED_RED_PIN|GATE_PIN|FOCUS_PIN, GPIO_PIN_RESET);
HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFE);
// Exit from STOP Mode procedure
SystemClock_Config();
ssd1306_WriteCommand(0xAF); // OLED On
GPIO_InitStruct.Pin = ENC_BUTTON_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_PULLDOWN;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
current_state = menu_navigation;
}
Menu();
if (current_state == running_timer || current_state == running_interval)
{
if(gate_flag)
{
// Reset Gate & Focus
HAL_GPIO_WritePin(GPIOA, FOCUS_PIN, GPIO_PIN_RESET);
HAL_GPIO_WritePin(GPIOA, GATE_PIN, GPIO_PIN_RESET);
HAL_TIM_Base_Stop_IT(&htim14);
HAL_Delay(500);
__HAL_TIM_SET_COUNTER(&htim14, 0);
HAL_TIM_Base_Start_IT(&htim14);
gate_flag = 0;
// If not last shot, go to Interval state
if(tmp_num_shots != 0)
{
tmp_int_minutes = set_int_minutes;
tmp_int_sec = set_int_sec;
tmp_exp_minutes = set_exp_minutes;
tmp_exp_sec = set_exp_sec;
current_state = running_interval;
HAL_GPIO_WritePin(GPIOA, LED_RED_PIN,GPIO_PIN_RESET); // 1s LED Off
}
else
{
HAL_TIM_Base_Stop_IT(&htim14);
__HAL_TIM_SET_COUNTER(&htim14, 0);
HAL_GPIO_WritePin(GPIOA, LED_RED_PIN,GPIO_PIN_RESET); // 1s LED Off
tmp_exp_minutes = set_exp_minutes;
tmp_exp_sec = set_exp_sec;
current_state = menu_navigation;
update_screen_flag = 1;
}
}
}
if (exiting_run)
{
HAL_TIM_Base_Stop_IT(&htim16);
HAL_Delay(1000);
exiting_run = 0;
HAL_TIM_Base_Start_IT(&htim16);
HAL_GPIO_WritePin(GPIOA, FOCUS_PIN, GPIO_PIN_RESET);
HAL_GPIO_WritePin(GPIOA, GATE_PIN, GPIO_PIN_RESET);
}
}
/* USER CODE END 3 */
}
void ultrasound_generator( uint32_t chanel ){
/* ##-1- Configure the TIM peripheral ****************************************************************************
TIM2 Configuration: generate 4 PWM signals with 4 different duty cycles.
In this example TIM2 input clock (TIM2CLK) is set to APB1 clock (PCLK1),
since APB1 prescaler is equal to 1.
TIM2CLK = PCLK1
PCLK1 = HCLK
=> TIM2CLK = HCLK = SystemCoreClock
To get TIM2 counter clock at 16 MHz, the prescaler is computed as follows:
Prescaler = (TIM2CLK / TIM2 counter clock) - 1
Prescaler = ((SystemCoreClock) /16 MHz) - 1
To get TIM2 output clock at 24 KHz, the period (ARR)) is computed as follows:
ARR = (TIM2 counter clock / TIM2 output clock) - 1
= 665
TIM2 Channel1 duty cycle = (TIM2_CCR1/ TIM2_ARR + 1)* 100 = 50%
**************************
20KHz-> Prescaler = ( (48MHz) / 20KHz) - 1=799
30KHz-> Prescaler = ( (48MHz) / 30KHz) - 1=399
*/
SystemClock_Config_48MHz();
MX_TIM3_Init();
HAL_TIM_PWM_Init(&htim3);
sConfigOC.Pulse=0;
HAL_GPIO_WritePin( DCDC_EN_GPIO_Port , DCDC_EN_Pin , 1 ); ///DCDC konverter engedélyezése (+15V)
HAL_TIM_PWM_ConfigChannel( &htim3 , &sConfigOC , TIM_CHANNEL_1);
HAL_TIM_PWM_ConfigChannel( &htim3 , &sConfigOC , TIM_CHANNEL_2);
HAL_TIM_PWM_ConfigChannel( &htim3 , &sConfigOC , TIM_CHANNEL_3);
HAL_TIM_PWM_ConfigChannel( &htim3 , &sConfigOC , TIM_CHANNEL_4);
HAL_TIM_PWM_Start(&htim3, TIM_CHANNEL_1);
HAL_TIM_PWM_Start(&htim3, TIM_CHANNEL_2);
HAL_TIM_PWM_Start(&htim3, TIM_CHANNEL_3);
HAL_TIM_PWM_Start(&htim3, TIM_CHANNEL_4);
for(int i=400; i < 700; i++){
//HAL_TIM_PWM_Stop(&htim3,chanel);
__HAL_TIM_SetAutoreload(&htim3,i*2);
__HAL_TIM_SetCompare(&htim3,chanel, i);
//HAL_TIM_OC_Init(&htim3);
//TIM_OC2_SetConfig( TIM3, &sConfigOC);
//HAL_TIM_PWM_Start( &htim3 , chanel );
HAL_Delay(30);
}
__HAL_TIM_SetCompare(&htim3,chanel, 0);
HAL_TIM_PWM_Stop( &htim3 , chanel );
HAL_TIM_PWM_DeInit( &htim3 );
HAL_TIM_Base_DeInit(&htim3);
GPIO_TIM3_OFF();
HAL_GPIO_WritePin( DCDC_EN_GPIO_Port , DCDC_EN_Pin , 0);
SystemClock_Config_8MHz();
}
void ultrasound (uint8_t bridge){ //ez a fv egyszerre csak egy hidat hajt meg!
uint16_t i,old_i,temp_i,f;
uint32_t CH1,CH2,CHx,CHy,tim,tim_now;
//bridge1=0,bridge2=1-> hogy melyik hidat hajtsa meg
if(bridge){ //bridge1
CH1=(uint32_t)TIM_CHANNEL_1;
CH2=(uint32_t)TIM_CHANNEL_2;
CHx=(uint32_t)TIM_CHANNEL_3;
CHy=(uint32_t)TIM_CHANNEL_4;
}else{ //bridge2
CH1=(uint32_t)TIM_CHANNEL_3;
CH2=(uint32_t)TIM_CHANNEL_4;
CHx=(uint32_t)TIM_CHANNEL_1;
CHy=(uint32_t)TIM_CHANNEL_2;
}
SystemClock_Config_48MHz();
HAL_Delay(20);
MX_TIM3_Init();
HAL_TIM_PWM_Init(&htim3);
sConfigOC.OCMode = TIM_OCMODE_PWM1;
sConfigOC.Pulse = 0;
sConfigOC.OCPolarity = TIM_OCPOLARITY_LOW;
sConfigOC.OCFastMode = TIM_OCFAST_DISABLE;
HAL_TIM_PWM_ConfigChannel( &htim3 , &sConfigOC , CH1);
sConfigOC.OCPolarity = TIM_OCPOLARITY_HIGH;
HAL_TIM_PWM_ConfigChannel( &htim3 , &sConfigOC , CH2);
HAL_TIM_PWM_ConfigChannel( &htim3 , &sConfigOC , CHx);
HAL_TIM_PWM_ConfigChannel( &htim3 , &sConfigOC , CHy);
HAL_TIM_PWM_Start(&htim3, CH1);
HAL_TIM_PWM_Start(&htim3, CH2);
HAL_TIM_PWM_Start(&htim3, CHx);
HAL_TIM_PWM_Start(&htim3, CHy);
//csattanás csökkentés, 19khz kiadás eloszor
HAL_GPIO_WritePin( DCDC_EN_GPIO_Port , DCDC_EN_Pin , 0 );
// HAL_GPIO_WritePin( DCDC_PWR_GPIO_Port , DCDC_PWR_Pin , 0 ); //open drain kimenet,pch fet,
//*****************************************
/*for( i=900 ; i >= 620 ; i-=3){
__HAL_TIM_SetAutoreload(&htim3,i*2);
__HAL_TIM_SetCompare(&htim3,CH1, i);
__HAL_TIM_SetCompare(&htim3,CH2, i);
HAL_Delay(1);
}*/
/***********************************
HAL_Delay(100);
__HAL_TIM_SetAutoreload(&htim3,i*2);
__HAL_TIM_SetCompare(&htim3,CH1, i);
__HAL_TIM_SetCompare(&htim3,CH2, i);
HAL_Delay(1000);*/
HAL_GPIO_WritePin( DCDC_EN_GPIO_Port , DCDC_EN_Pin , 1 );
HAL_Delay(100);
//19KHz-620 // 27KHz-440
old_i=i;
for(uint8_t x=0; x < soundNum; x++){
// a következo hanghoz kis lépésenként jutunk, ígty nincs csattanás
srand(HAL_GetTick());
i=(rand()%210)+440;
//i=210+440;
/*
if( old_i < i){
// ha az új hang kissebb frekvenciájó -> nagyobb i
for( temp_i=old_i ; i >= temp_i; temp_i++){
__HAL_TIM_SetAutoreload(&htim3,temp_i*2);
__HAL_TIM_SetCompare(&htim3,CH1, temp_i);
__HAL_TIM_SetCompare(&htim3,CH2, temp_i);
HAL_Delay(1);
}
}else{
//ha az uj hang nagypbb frekvenciáju-> kisebb i
for( temp_i=old_i ; i <= temp_i; temp_i--){
__HAL_TIM_SetAutoreload(&htim3,temp_i*2);
__HAL_TIM_SetCompare(&htim3,CH1, temp_i);
__HAL_TIM_SetCompare(&htim3,CH2, temp_i);
HAL_Delay(1);
}
}
*/
__HAL_TIM_SetAutoreload(&htim3,i*2);
__HAL_TIM_SetCompare(&htim3,CH1, i);
__HAL_TIM_SetCompare(&htim3,CH2, i);
old_i=i;
tim=HAL_GetTick(); //jelenlegi ido lekérdezés
tim_now=HAL_GetTick();
f=i%5;
while( sDelay >= (tim_now-tim) && tim <= tim_now ){ ///késleltetés
if(f==3){
for(temp_i=0 ; temp_i < 10 ;temp_i++){ //itt nagyobb lesz a frekvencia
i+=1;
__HAL_TIM_SetAutoreload(&htim3,i*2);
__HAL_TIM_SetCompare(&htim3,CH1, i);
__HAL_TIM_SetCompare(&htim3,CH2, i);
HAL_Delay(1);
}
for(temp_i=0 ; temp_i < 10 ;temp_i++){ //itt kissebb lesz a frekvencia
i-=1;
__HAL_TIM_SetAutoreload(&htim3,i*2);
__HAL_TIM_SetCompare(&htim3,CH1, i);
__HAL_TIM_SetCompare(&htim3,CH2, i);
HAL_Delay(1);
}
}
tim_now=HAL_GetTick();
}
// HAL_Delay(sDelay);
randCount++;
}
//csattanás csökkentés, 19khz kiadás eloszor
HAL_GPIO_WritePin( DCDC_EN_GPIO_Port , DCDC_EN_Pin , 0);
for( i=i ; i <= 900 ; i+=3){
__HAL_TIM_SetAutoreload(&htim3,i*2);
__HAL_TIM_SetCompare(&htim3,CH1, i);
__HAL_TIM_SetCompare(&htim3,CH2, i);
HAL_Delay(1);
}
HAL_Delay(100);
HAL_TIM_PWM_Stop( &htim3 , CH1 );
HAL_TIM_PWM_Stop( &htim3 , CH2 );
HAL_TIM_PWM_Stop( &htim3 , CHx );
HAL_TIM_PWM_Stop( &htim3 , CHy );
HAL_TIM_PWM_DeInit( &htim3 );
// HAL_GPIO_WritePin( DCDC_PWR_GPIO_Port , DCDC_PWR_Pin , 1); //open drain kimenet,pch fet,
HAL_Delay(100);
SystemClock_Config_8MHz();
GPIO_TIM3_OFF();
HAL_Delay(100);
}
void beeps (uint8_t num,uint8_t bridge){
uint16_t temp1;
uint32_t CH1,CH2,CHx,CHy;
// HAL_GPIO_WritePin( DCDC_PWR_GPIO_Port , DCDC_PWR_Pin , 0 ); //open drain kimenet,pch fet,
HAL_Delay(100);
HAL_GPIO_WritePin( DCDC_EN_GPIO_Port , DCDC_EN_Pin , 1 ); //open drain kimenet,pch fet,
//bridge1=0,bridge2=1-> hogy melyik hidat hajtsa meg
if(bridge){ //bridge1
CH1=(uint32_t)TIM_CHANNEL_1;
CH2=(uint32_t)TIM_CHANNEL_2;
CHx=(uint32_t)TIM_CHANNEL_3;
CHy=(uint32_t)TIM_CHANNEL_4;
}else{ //bridge2
CH1=(uint32_t)TIM_CHANNEL_3;
CH2=(uint32_t)TIM_CHANNEL_4;
CHx=(uint32_t)TIM_CHANNEL_1;
CHy=(uint32_t)TIM_CHANNEL_2;
}
//SystemClock_Config_48MHz();
MX_TIM3_Init();
HAL_TIM_PWM_Init(&htim3);
sConfigOC.OCMode = TIM_OCMODE_PWM1;
sConfigOC.Pulse = 0;
sConfigOC.OCPolarity = TIM_OCPOLARITY_LOW;
sConfigOC.OCFastMode = TIM_OCFAST_DISABLE;
HAL_TIM_PWM_ConfigChannel( &htim3 , &sConfigOC , CH1);
sConfigOC.OCPolarity = TIM_OCPOLARITY_HIGH;
HAL_TIM_PWM_ConfigChannel( &htim3 , &sConfigOC , CH2);
HAL_TIM_PWM_ConfigChannel( &htim3 , &sConfigOC , CHx);
HAL_TIM_PWM_ConfigChannel( &htim3 , &sConfigOC , CHy);
HAL_TIM_PWM_Start(&htim3, CH1);
HAL_TIM_PWM_Start(&htim3, CH2);
HAL_TIM_PWM_Start(&htim3, CHx);
HAL_TIM_PWM_Start(&htim3, CHy);
__HAL_TIM_SetCompare(&htim3,CH2,0);
for( uint8_t i=0 ; i<num ; i++){
temp1=3500;
for(uint8_t ii=0; ii<10 ; ii++){
__HAL_TIM_SetAutoreload(&htim3,temp1*2);
__HAL_TIM_SetCompare(&htim3,CH1, temp1);
//__HAL_TIM_SetCompare(&htim3,CH2,temp1);
temp1 -=6;
HAL_Delay(18);
}/*
for(uint8_t ii=0; ii<10 ; ii++){
__HAL_TIM_SetAutoreload(&htim3,temp1*2);
__HAL_TIM_SetCompare(&htim3,CH1, temp1);
// __HAL_TIM_SetCompare(&htim3,CH2,temp1);
temp1 +=15;
HAL_Delay(9);
}*/
__HAL_TIM_SetCompare(&htim3,CH1, 0);
// __HAL_TIM_SetCompare(&htim3,CH2,0);
HAL_Delay(340);
}
__HAL_TIM_SetCompare(&htim3,CH1, 0);
HAL_TIM_PWM_Stop( &htim3 , CH1 );
HAL_TIM_PWM_Stop( &htim3 , CH2 );
HAL_TIM_PWM_Stop( &htim3 , CHx );
HAL_TIM_PWM_Stop( &htim3 , CHy );
HAL_TIM_PWM_DeInit( &htim3 );
HAL_TIM_Base_DeInit(&htim3);
GPIO_TIM3_OFF();
HAL_GPIO_WritePin( DCDC_EN_GPIO_Port , DCDC_EN_Pin , 0 ); //open drain kimenet,pch fet,
HAL_Delay(100);
// HAL_GPIO_WritePin( DCDC_PWR_GPIO_Port , DCDC_PWR_Pin , 0 );
HAL_Delay(1000);
}
void uartTester(){
//UART fogadás, teszteléshez ---------------------------------------------------------
uint8_t pData;
PutString("S");
HAL_UART_Receive(&huart1,&pData,1,100);
if(pData=='O'){
HAL_GPIO_TogglePin(Kimenet_GPIO_Port,Kimenet_Pin);
PutString("R");
HAL_UART_Receive(&huart1,&pData,1,1000);
while(pData != 'A')
HAL_UART_Receive(&huart1,&pData,1,1000);
HAL_GPIO_WritePin( DCDC_EN_GPIO_Port , DCDC_EN_Pin , 1 );
PutString("R");
HAL_UART_Receive(&huart1,&pData,8,1000);
while(pData != 'B')
HAL_UART_Receive(&huart1,&pData,8,1000);
soundNum=1;
sounDelay=10;
SystemClock_Config_48MHz();
HAL_Delay(2);
MX_TIM3_Init();
HAL_TIM_PWM_Init(&htim3);
sConfigOC.OCMode = TIM_OCMODE_PWM1;
sConfigOC.Pulse = 0;
sConfigOC.OCPolarity = TIM_OCPOLARITY_LOW;
sConfigOC.OCFastMode = TIM_OCFAST_DISABLE;
HAL_TIM_PWM_ConfigChannel( &htim3 , &sConfigOC , TIM_CHANNEL_1);
sConfigOC.OCPolarity = TIM_OCPOLARITY_HIGH;
HAL_TIM_PWM_ConfigChannel( &htim3 , &sConfigOC , TIM_CHANNEL_2);
HAL_GPIO_TogglePin(Kimenet_GPIO_Port,Kimenet_Pin);
HAL_TIM_PWM_Start(&htim3, TIM_CHANNEL_1);
HAL_TIM_PWM_Start(&htim3, TIM_CHANNEL_2);
uint16_t i=630;
__HAL_TIM_SetAutoreload(&htim3,i*2);
__HAL_TIM_SetCompare(&htim3,TIM_CHANNEL_1, i);
__HAL_TIM_SetCompare(&htim3,TIM_CHANNEL_2, i);
HAL_Delay(500);
PutString("R");
HAL_UART_Receive(&huart1,&pData,8,1000);
while(pData != 'C')
HAL_UART_Receive(&huart1,&pData,8,1000);
HAL_GPIO_WritePin( DCDC_EN_GPIO_Port , DCDC_EN_Pin , 0);
HAL_TIM_PWM_Stop( &htim3 , TIM_CHANNEL_1 );
HAL_TIM_PWM_Stop( &htim3 , TIM_CHANNEL_2 );
HAL_TIM_PWM_DeInit( &htim3 );
SystemClock_Config_8MHz();
HAL_ADC_MspDeInit(&hadc);
HAL_UART_MspDeInit(&huart1);
HAL_TIM_Base_DeInit(&htim3);
while(1){
HAL_GPIO_TogglePin(Kimenet_GPIO_Port,Kimenet_Pin);
HAL_Delay(200);
}
}
}
int main(void)
{
/* USER CODE BEGIN 1 */
CMDLINE_CONTEXT cmd_context;
const char *zhonx_info = (char *)CONFIG_ZHONX_INFO_ADDR;
/* USER CODE END 1 */
/* MCU Configuration----------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* Configure the system clock */
SystemClock_Config();
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_DMA_Init();
MX_ADC1_Init();
MX_ADC2_Init();
MX_ADC3_Init();
MX_I2C1_Init();
MX_RNG_Init();
MX_TIM1_Init();
MX_TIM2_Init();
MX_TIM3_Init();
MX_TIM4_Init();
MX_TIM5_Init();
MX_TIM6_Init();
MX_TIM7_Init();
MX_TIM8_Init();
MX_TIM11_Init();
MX_USART3_UART_Init();
/* USER CODE BEGIN 2 */
expanderInit();
HAL_Delay(100);
mainControlInit();
ssd1306Init(0);
timesBaseInit();
ledPowerBlink(990, 10);
settingsInit();
mulimeterInit();
bluetoothInit();
toneInit();
spyPostInit();
positionControlSetPositionType(GYRO);
mainControlSetFollowType(NO_FOLLOW);
toneSetVolulme(100);
tone(F4, 50);
toneItMode(A4, 50);
// Register Output callback
cmd_context.out = blockingPrintf;
// Initialize Command Line module
cmdline_init(&cmd_context);
// Check if robot name is populated in Flash
memset(zhonxName, 0, sizeof(zhonxName));
// Retrieve ZHONX information from flash if any
if (zhonx_info[0] == 'Z')
{
strcpy(zhonxName, zhonx_info);
}
while (zhonxName[0] == 0)
{
menu(zhonxNameMenu);
}
while (1)
{
menu(mainMenu);
powerOffConfirmation();
}
/* USER CODE END 2 */
/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
;
/* USER CODE END WHILE */
/* USER CODE BEGIN 3 */
/* USER CODE END 3 */
}