/**
* xgene_ahci_do_hardreset - Issue the actual COMRESET
* @link: link to reset
* @deadline: deadline jiffies for the operation
* @online: Return value to indicate if device online
*
* Due to the limitation of the hardware PHY, a difference set of setting is
* required for each supported disk speed - Gen3 (6.0Gbps), Gen2 (3.0Gbps),
* and Gen1 (1.5Gbps). Otherwise during long IO stress test, the PHY will
* report disparity error and etc. In addition, during COMRESET, there can
* be error reported in the register PORT_SCR_ERR. For SERR_DISPARITY and
* SERR_10B_8B_ERR, the PHY receiver line must be reseted. The following
* algorithm is followed to proper configure the hardware PHY during COMRESET:
*
* Alg Part 1:
* 1. Start the PHY at Gen3 speed (default setting)
* 2. Issue the COMRESET
* 3. If no link, go to Alg Part 3
* 4. If link up, determine if the negotiated speed matches the PHY
* configured speed
* 5. If they matched, go to Alg Part 2
* 6. If they do not matched and first time, configure the PHY for the linked
* up disk speed and repeat step 2
* 7. Go to Alg Part 2
*
* Alg Part 2:
* 1. On link up, if there are any SERR_DISPARITY and SERR_10B_8B_ERR error
* reported in the register PORT_SCR_ERR, then reset the PHY receiver line
* 2. Go to Alg Part 3
*
* Alg Part 3:
* 1. Clear any pending from register PORT_SCR_ERR.
*
* NOTE: For the initial version, we will NOT support Gen1/Gen2. In addition
* and until the underlying PHY supports an method to reset the receiver
* line, on detection of SERR_DISPARITY or SERR_10B_8B_ERR errors,
* an warning message will be printed.
*/
static int xgene_ahci_do_hardreset(struct ata_link *link,
unsigned long deadline, bool *online)
{
const unsigned long *timing = sata_ehc_deb_timing(&link->eh_context);
struct ata_port *ap = link->ap;
struct ahci_host_priv *hpriv = ap->host->private_data;
struct xgene_ahci_context *ctx = hpriv->plat_data;
struct ahci_port_priv *pp = ap->private_data;
u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
void __iomem *port_mmio = ahci_port_base(ap);
struct ata_taskfile tf;
int rc;
u32 val;
/* clear D2H reception area to properly wait for D2H FIS */
ata_tf_init(link->device, &tf);
tf.command = ATA_BUSY;
ata_tf_to_fis(&tf, 0, 0, d2h_fis);
rc = sata_link_hardreset(link, timing, deadline, online,
ahci_check_ready);
val = readl(port_mmio + PORT_SCR_ERR);
if (val & (SERR_DISPARITY | SERR_10B_8B_ERR))
dev_warn(ctx->dev, "link has error\n");
/* clear all errors if any pending */
val = readl(port_mmio + PORT_SCR_ERR);
writel(val, port_mmio + PORT_SCR_ERR);
return rc;
}
ahci_init_controller(host);
}
static int ahci_vt8251_hardreset(struct ata_link *link, unsigned int *class,
unsigned long deadline)
{
struct ata_port *ap = link->ap;
bool online;
int rc;
DPRINTK("ENTER\n");
ahci_stop_engine(ap);
rc = sata_link_hardreset(link, sata_ehc_deb_timing(&link->eh_context),
deadline, &online, NULL);
ahci_start_engine(ap);
DPRINTK("EXIT, rc=%d, class=%u\n", rc, *class);
/* vt8251 doesn't clear BSY on signature FIS reception,
* request follow-up softreset.
*/
return online ? -EAGAIN : rc;
}
static int ahci_p5wdh_hardreset(struct ata_link *link, unsigned int *class,
unsigned long deadline)
{
struct ata_port *ap = link->ap;
* Kernel thread context (may sleep)
*
* RETURNS:
* 0 on success, -errno otherwise.
*/
int sata_pmp_std_hardreset(struct ata_link *link, unsigned int *class,
unsigned long deadline)
{
const unsigned long *timing = sata_ehc_deb_timing(&link->eh_context);
u32 tmp;
int rc;
DPRINTK("ENTER\n");
/* do hardreset */
rc = sata_link_hardreset(link, timing, deadline);
if (rc) {
ata_link_printk(link, KERN_ERR,
"COMRESET failed (errno=%d)\n", rc);
goto out;
}
/* clear SError bits including .X which blocks the port when set */
rc = sata_scr_write(link, SCR_ERROR, 0xffffffff);
if (rc) {
ata_link_printk(link, KERN_ERR, "failed to clear SError "
"during hardreset (errno=%d)\n", rc);
goto out;
}
/* if device is present, follow up with srst to wait for !BSY */
